Search Results

Search found 5064 results on 203 pages for 'automatic ref counting'.

Page 154/203 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

• Virtual IPv6 Network between VirtualBox VMs

  - by Ben

  I'm trying to create a virtual IPv6 network as a test environment. I have 5 VirtualBox VMs (Ubuntu Server) with network adapters using host-only networking. You can imagine them being connected in series and every machine connects 2 subnets. I want to ping the last machine from the first one: On: 2001:db8:aaaa::100 I want to ping 2001:db8:dddd::101 (Note: there is no cccc network in between) Only static configuration and routes are used: /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::100 netmask 64 /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::101 netmask 64 auto eth1 iface eth1 inet6 static address 2001:db8:bbbb::100 netmask 64 up ip -6 route add 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 down ip -6 route del 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 I thought there might be some automatic route discovery going on. Anyway, ping6 2001:db8:dddd::100 will not work from aaaa::100 When I add the route: ip -6 route add 2001:db8:dddd::/64 via 2001:db8:aaaa::101 it will work. But the next interface in the same network dddd::101 is not reachable. How could that be? There is a machine with an interface bbbb::101 and another dddd::100 and I can ping the latter one, but the machine connected to it, dddd::101 not?? I also have also turned on forwarding. Any ideas?

  Read the article

• How can you force the start and end date of a task in Microsoft Project to be on the same day?

  - by Hauke P.

  I have a task called "Interview person A about topic X". The task's duration is set to 2 hours. The start date of the task should automatically be calculated taking dependencies and resource availabilities into account. My question boils down to: How can I force this task to start and end on the same date? Background: In my case, Microsoft Project sets the start date to a Friday at 5pm. As my working hours are set to 8am to 12am and 1pm to 6pm (Mon-Fri), Microsoft Project "splits up" the task at 6pm on Friday and plans to continue it at 8am on the following Monday. However, it does not make any sense to stop the interview on a Friday and restart it on Monday. Therefore the automatic suggestion is not helpful in this case. That's why I'm looking for a way way to force the task to start and end on the very same day. (In my example, I'd like Microsoft Project to delay the start date of the task until Monday 8am as this is the first time slot in which the task "fits in completely".) By the way: I have lots of such cases... for that reason it would be really great if there was a solution that doesn't just deal with this single special case.)

  Read the article

• My own personal use of Oracle Linux

  - by wcoekaer

  It always is easier to explain something with examples... Many people still don't seem to understand some of the convenient things around using Oracle Linux and since I personally (surprise!) use it at home, let me give you an idea. I have quite a few servers at home and I also have 2 hosted servers with a hosted provider. The servers at home I use mostly to play with random Linux related things, or with Oracle VM or just try out various new Oracle products to learn more. I like the technology, it's like a hobby really. To be able to have a good installation experience and use an officially certified Linux distribution and not waste time trying to find the right libraries, I, of course, use Oracle Linux. Now, at least I can get a copy of Oracle Linux for free (even if I was not working for Oracle) and I can/could use that on as many servers at home (or at my company if I worked elsewhere) for testing, development and production. I just go to http://edelivery.oracle.com/linux and download the version(s) I want and off I go. Now, I also have the right (and not because I am an employee) to take those images and put them on my own server and give them to someone else, I in fact, just recently set up my own mirror on my own hosted server. I don't have to remove oracle-logos, I don't have to rebuild the ISO images, I don't have to recompile anything, I can just put the whole binary distribution on my own server without contract. Perfectly free to do so. Of course the source code of all of this is there, I have a copy of the UEK code at home, just cloned from https://oss.oracle.com/git/?p=linux-2.6-unbreakable.git. And as you can see, the entire changelog, checkins, merges from Linus's tree, complete overview of everything that got changed from kernel to kernel, from patch to patch, errata to errata. No obfuscating, no tar balls and spending time with diff, or go read bug reports to find out what changed (seems silly to me). Some of my servers are on the external network and I need to be current with security errata, but guess what, no problem, my servers are hooked up to http://public-yum.oracle.com which is open, free, and completely up to date, in a consistent, reliable way with any errata, security or bugfix. So I have nothing to worry about. Also, not because I am an employee. Anyone can. And, with this, I also can, and have, set up my own mirror site that hosts these RPMs. both binary and source rpms. Because I am free to get them and distribute them. I am quite capable of supporting my servers on my own, so I don't need to rely on the support organization so I don't need to have a support subscription :-). So I don't need to pay. Neither would you, at least not with Oracle Linux. Another cool thing. The hosted servers came (unfortunately) with Centos installed. While Centos works just fine as is, I tend to prefer to be current with my security errata(reliably) and I prefer to just maintain one yum repository instead of 2, I converted them over to Oracle Linux as well (in place) so they happily receive and use the exact same RPMs. Since Oracle Linux is exactly the same from a user/application point of view as RHEL, including files like /etc/redhat-release and no changes from .el. to .centos. I know I have nothing to worry about installing one of the RHEL applications. So, OL everywhere makes my life a lot easier and why not... Next! Since I run Oracle VM and I have -tons- of VM's on my machines, in some cases on my big WOPR box I have 15-20 VMs running. Well, no problem, OL is free and I don't have to worry about counting the number of VMs, whether it's 1, or 4, or more than 10 ... like some other alternatives started doing... and finally :) I like to try out new stuff, not 3 year old stuff. So with UEK2 as part of OL6 (and 6.3 in particular) I can play with a 3.0.x based kernel and it just installs and runs perfectly clean with OL6, so quite current stuff in an environment that I know works, no need to toy around with an unsupported pre-alpha upstream distribution with libraries and versions that are not compatible with production software (I have nothing against ubuntu or fedora or opensuse... just not what I can rely on or use for what I need, and I don't need a desktop). pretty compelling. I say... and again, it doesn't matter that I work for Oracle, if I was working elsewhere, or not at all, all of the above would still apply. Student, teacher, developer, whatever. contrast this with $349 for 2 sockets and oneguest and selfsupport per year to even just get the software bits.

  Read the article

• BSOD error 0x0000006B PROCESS1_INITIALIZATION_FAILED on boot

  - by DontCare4Free

  I reinstalled League of Legends because the patcher always gave me an error. However, out of complete stupidness I didn't uninstall the old installation first because I thought that it would simply replace the files. However, when the installer bar got to 100% it simply minimized. Then I closed the application from the task manager. I tried uninstalling it after a failed attempt to start it up. The same behavior as when I installed it. Then I tried reinstalling where it simply presented the InstallShield Modify/Repair/Remove menu and I selected repair. Nothing happened. Then I tried selecting Modify, then seeing that the only option (called DefaultFeature) was unchecked. Same behaviour as install/uninstall. After seeing that it still failed, I uninstalled again. And after that I deleted C:\Program Files (x86)\League of Legends manually. When I tried installing LoL again it still thought I had it, so I chose repair. This time something actually happened, but it installed the whole game to C:\Windows. Seeing what was going on I clicked cancel and then started it up to try uninstalling it. However, I got an error message about something not being registered and then the minimization to I decided to let it repair completely. Then I uninstalled it and it gave only the minimization. However, when I rebooted another application started up complaining about some library being absent. So I decided to do a system restore. After letting it complete I got a BSOD every time I tried starting up Windows normally or in safe mode. However, system recovery mode works, although the system recovery automatic repair does not fix it. After a bit of searching I found a Microsoft KB article about it (981833) and tried following the workaround instructions. Nothing happened. I am using Windows 7 Home Premium 64-bit and Ubuntu 10.04 LTS 64-bit installed with WUBI.

  Read the article

• DVI splitter not working as expected/confusion between DVI-D and -I

  - by Freakishly

  Hey guys, thanks for looking. I have an ATI FirePro™ V3700 in my desktop machine, and I have been running a dual-monitor setup quite effortlessly, thanks to the two DVI ports on the card. I came upon a third monitor, and wanted to extend my desktop to 3 screens, so I purchased a DVI splitter from Amazon. Now, I can only duplicate the second monitor onto the third, not extend it. I've tried all possible combinations of input to no avail. Here's the setup: The ATI FirePro™ V3700 has two Dual-Link DVI-I outputs The splitter splits a single Dual-Link DVI-I port into two Dual-Link DVI-I outputs Two of the monitors are NEC E222W, and the third monitor is a Dell 2001FP. Each monitor has one D-Sub and one Dual-Link DVI-D input. Cables going from the video card to the monitors are two Dual-Link DVI-D to the NECs and one Single-Link DVI-D to the Dell. Is the problem likely with the DVI-D/DVI-I mismatch? Or is it with the cable on the Dell that is only a Single-Link? The cables are easily replaceable, the monitors not so much. Thanks for your time, I really appreciate it. http://www.amd.com/us/products/workstation/graphics/ati-firepro-3d/v3700/Pages/v3700-specs.aspx http://www.amazon.com/Cables-Unlimited-DVI-D-Splitter-PCM-2260/product-reviews/B000H09RFM/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 www dot newegg dot com/Product/Product.aspx?Item=N82E16824002495 accessories dot us dot dell dot com/sna/PopupProductDetail.aspx?cs=19&l=en&c=us&sku=320-1578 Apologies for the fudged links, I'm new here and they won't let me post more than two :P

  Read the article

• Routing and authenticating all access through squid

  - by Knight Samar

  Hi, I want to route all Internet access in my network through a Squid proxy server and authenticate and log all users. I want this to be a client-independent setting so that no one needs to do anything on their browsers or machines. I have set my network gateway as the proxy server so that all traffic will be sent to it. I have done this using options in DHCP server. Now I tried using squid as a transparent proxy, but then it won't authenticate in that mode. I tried using iptables to route all traffic to port 3128 but it won't popup the authentication dialog box from SQUID. I tried telling DHCP to give WPAD to all clients by placing a WPAD file on a webserver containing the following for automatic proxy configuration on clients: Changes in dhcpd.conf option wpad code 252 =test; option wpad "\n\000"; option wpad "http://192.168.1.5/wpad.dat\n"; The WPAD file: function FindProxyForURL(url,host) { return "PROXY squid-server-ip-address:3128 ; DIRECT "; } But the browsers (different versions of Firefox and IE) seem to ignore it. :( What should I do ?

  Read the article

• How do I do a mail merge that includes images?

  - by Ian Ringrose

  I am trying to find out the practicalities of doing a mail merge when each “record” to be merged on includes some images. I need to: print letters And envelopes Both the letters and the envelopes have: Fixed text Fixed images Text that come from the mail merge record Images that come from the mail merge record I don’t know if all images will be the same size for every record, so a bit of simple “on the fly” automatic formatting may be needed . I need to be able to repeat a single item if I get a problem (e.g when folding the letter). What problems am I likely to have? Is Word 2007 up to this sort of mail merging, or should I be looking at a report writing tool? How do I restart a print run after a printer jam etc? What format should I store the “records” and there images in? E.g Can standard software cope with images that are stored in separate files named after the “CustomerId” that is in the “record” (I can write custom software if needed, but would rather use standard “of-the-shelf” software for the printing, I am planning on custom software for the data creation, so can output in whatever format is needed)

  Read the article

• Task scheduled to wake laptop - only works when lid is open

  - by JD Pack

  I am running Windows 7 Starter on an Acer Aspire One laptop. I want my laptop to automatically run a task (backup the HDD to a network drive) once a week in the middle of the night. I scheduled the task in "Task Scheduler" and checked the box to wake the computer to run the task. I also changed the advanced power settings to allow wake timers. This was half of the solution. It now works flawlessly when the lid is open... the computer can wake itself up from either sleep or hibernate mode to perform the backup. When the lid is closed however, its sleeping beauty. Any ideas? I don't want to have to remember to open the lid once a week. It sort of defeats the purpose of an "automatic" backup. Update: I discovered that it can wake from sleep (or hybrid sleep), but not from hibernate when the lid is closed. This is good news. I'd still be curious about how to get it to work from hibernate, but I'm pretty happy about waking from sleep at least.

  Read the article

• Windows 8 Internet Explorer 11 proxy automation script

  - by Stefan Bollmann

  Similar to this post, I'd like to change my proxy settings using a script. However, it fails. When I am behind the proxy, IE does not connect to the internet. Here I try the first solution from craig: function FindProxyForURL(url, host) { if (isInNet(myIpAddress(), "myactualip", "myactualsubnetip")) return "PROXY proxyasshowninpicture:portihavetouseforthisproxy_see_picture"; else return "DIRECT"; } This script is saved as proxy.pac in c:\windows and my configuration is* in LAN settings: No automatically detected settings, yes, use automatic config script: file://c:/windows/proxy.pac No proxy server. So, what am I doing wrong? ---------------- update -------------- However, when I set up a proxy in my LAN configurations: IE -> Internet Options -> Connections -> LAN Settings check: Use a proxy Server for your LAN Address: <a pingable proxy> Port: <portnr> everything is fine for this environment. Now I try a simpler script like function FindProxyForURL(url, host) { return "PROXY <pingable proxy>:<portnr>; DIRECT"; } With a configuration described above** I am not able to get through the proxy.

  Read the article

• Getting Started in SuSE as an Ubuntu User

  - by Subhamoy Sengupta

  I am not a Linux newbie, but haven't touched SuSE in a very very long time (last time I tried it, it was SuSE 7!). Finally now I felt like giving it a try, and many things seem strange or unnecessarily complex. I have a series of questions. How do I ensure that my packages are uptodate? It sounds silly, but I tried the obvious methods already. I have disabled the default repositories that show up when you do zypper lr, and added Tumbleweed and packman repositories (Essentials, Multimedia, Extra). Then I did a sudo zypper ref --force and then sudo zypper dup, and it tells me many dependencies are not met. I have already added solder.allowVendorChange=true to /etc/zypp/zypp.conf, so it should not care which repository the latest versions are in, and just upgrade to it. Even when I chose to skip the packages with unmet dependencies, and seemed like quite a bit happened in the background, I opened Firefox afterwards and the version was 7! I am guessing things did not go as expected. But of course this is not a problem with SuSE, but I am not understanding the system right. How do I do it right? When I start typing arguments of a command, for example sudo zypper install, when I type sudo zypper ins and keep hitting TAB, nothing happens! It always worked in Ubuntu and I feel very uneasy with this. Is this how SuSE is supposed to be? When I try to install something, and I start writing its name, even though the package exists and I am sure of it, hitting TAB does not autocomplete it. This is also quite inconvenient. Why is it not happening? There are many things in SuSE that are really great, and I think I will stay with it and not go back to Ubuntu once I settle these very rudimentary issues. But right now they are giving me a lot of grief! Please help!

  Read the article

• Host system resets (crashes) when using VMWare or VirtualBox and 64-bit guest systems

  - by sinni800

  I have been trying to install virtual systems on VMWare for a while now and encountered strange behaviour from my PC. The behaviour is as follows: On "automatic" virtualization mode it either outputs a cryptic error message (can MAYBE give later, if I can reproduce) right on startup (before even the BIOS) or it resets the complete HOST system (blackscreen, bios...) If I install a Windows XP on it it works well on "binary translation" mode. If I try installing Linux on it, in "binary translation" mode it crashes 1 or 2 seconds after I hit enter on the GRUB selection screen (after the first page of kernel messages rolled in) Using VirtualBox it crashes right in the BIOS. It gave me a Bluescreen though! 0x00000101: CLOCK_WATCHDOG_TIMEOUT: a clock interrupt was not received on a secondary processor within the allocated time interval NEWS: I tried VirtualBox again and it did not completely crash the computer this time. It gave me a critical error and a log file: http://pastebin.com/yKZSDs91 In conclusion, it will crash instantly if VT-x is activated. If not, it seemingly only crashed if I try to install something with 64 bits. Another update: Yes, it ONLY crashes when the guest is 64 bit! What I tried: Reinstalling Windows (my Windows installation was quite broken so it seemed natural. Didn't work though.) New BIOS What I am certain of: Virtualization extensions are activated in the BIOS What my computer specs are: ASUS P8P67 LE mainboard, newest BIOS/EFI firmware Intel Core i5 2500k Ati Radeon HD 5770 16 GB Corsair 1333mhz DDR3 RAM, 4 X 4 GB

  Read the article

• Vmware Workstation, Win7 host, Ubuntu guests with Nat + Host-only networks but they cannot connect to the Internet

  - by Ikon

  I have a Win7 host machine with Vmware Workstation. In the workstation I have 3 Ubuntu installed. All 3 Ubuntu guests have a Nat network - to access the internet without asking the router for a local address - and a Host-only network - to connect all Ubuntu quests and the host in a private network for internal communication, without touching the router. When I try to make any of the Ubuntu quests to get data from the internet - assuming that they would figure out that the Nat-ed interface can access the requested data - they fail and report that there is no route to my query. If I disconnect the 2nd interface on the Ubuntu guests with the Host-only network and restart networking, they start to know the route to the internet. Odd, during the installation of the guests they asked which of the 2 given interfaces - with Nat and Host-only config - should be used to get updates during installation and they oddly managed to get the updates. Not so after the installation has finished and rebooted. I have checked the Virtual Network Editor that the Nat interface should use my real network card to access the net, so there should be no problem. I wish not to use the router's dhcp service to give the Ubuntu quests an address, and also I don't want the guests to be accessable from the local network directly, but only by the host - that's the Host-only network is for. Any suggestions? Edit: 192.168.189.0 is the Nat interface and 192.168.7.0 is the Host-only. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.7.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.189.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.189.2 0.0.0.0 UG 100 0 0 eth0

  Read the article

• Windows 7 Update freezes - what to do?

  - by Tom Tom

  Hi, Yesterday I shutdown my notebook, and Windows 7 Ultimate started to install automatic updates. After one hour, I noticed that the update was still running. I thought OK, I shall go to sleep and let it run. In the morning it was still running. Thus, I thought it had crashed, forced a shutdown of the notebook and then restarted it. With the same effect that the notebook is "freezing" at "Install Update 1 of 5". It does not look like it has crashed. The progress wheel is still moving. But it does not make any progress... Would appreciate any help! Edit: OK, I was able to log-in into safe mode. This way I passed the install update screen. I do not want to generally disable updates, what can I do to not install the last update, which is creating troube. Or how can I find out whats the problem with the last update?

  Read the article

• I need to preserve a tape using symantec backup exec. I'm aving trouble doing so

  - by MrVimes

  Please forgive me if this is the wrong stack exchange site. Please suggest which one I should post this to if it is. There's an automatic tape machine running in a remote location, with software (symantec backup exec 11d) Recently one of the servers being backed up had problems with its raid controller, so one of the drives has become invisible. I need to preserve the last good backup of that drive so I am trying to replace the tape with the most recent backup of that drive on it with one of the scratch tapes (blank tapes) present in the machine. I've tried the following... Associate the blank media with the media set in question (Wednesday) For the existing media (the tape with the data I want to keep) I click 'move to vault' and move it to the offline vault. I associate it with something other than 'Wednesday' (a media set called 'keep data infinitely...') I then do an inventory on that slot. The above steps I'm led to believe are supposed to put the fresh tape in the slot that had the tape I want to keep in it. But it just keeps showing up as containing the tape I want to keep after the inventory. (after refreshing the device tree) I am a complete newbie with this software. Can you tell me what I'm doing wrong, and/or tell me how to acheive my desired goal Edit: Just want to point out that I did try to get help directly from symantec with this, but having jumped through countless hoops to create an account and create a support ticket my progress was halted by requiring something called a 'tecnical contact id' at the final step with no explanation of what it is or how to get one.

  Read the article

• How could I embed formatted XML source in WORD documents?

  - by eckes

  I'm writing a documentation with WORD that contains XML source code (whole files) as examples. The way I'm embedding the currently XML is quite cumbersome and doesn't seem to me as really maintainable: I'm finishing the editing of the document in WORD and create a PDF from it using Acrobat next, I open my XML files (2x input files, 2x generated output files) with IE and print them with the PDF printer supplied by Acrobat now, I open up Acrobat Pro and attach the four XML-PDF files to my original document The problem with that work flow for me is that it involves too much manual labor in order to get the documentation done. What I've tried up to now is not really satisfying for me: converting each XML to PDF and appending them like described above opening the XML files with SCiTE, copy as RTF and paste into Word playing around with the LaTeX packages minted, pygments and listings (I could write the docs with LaTeX too) but found some unsolvable problems in each of these packages I'm searching for a way that produces my documentation more automatic. For example embedding the XML files including formatting of IE (which I find quite readable). The files should be included by reference so that I don't have to paste the XML sources manually every time the XML changes.

  Read the article

• Problems with USB-Devices using VDR

  - by emmsinator

  Hey Guys, I'm using VDR on vSphere4. It works sucessfully. I've already backuped several VMs with VDR and I like it very much. But now we got a problem. We have 2 VMs, using an USB-Device Server with a stick plugged in, which is definetely need by these 2 VMs for Licensing and so. Every time, I start the Backup process, the VMs lost the communication to the USB-Server and its stick after building the snapshot and while online. Because of that, the software on these VMs can't work correctly. I have to restart both Machines to solve this problem. These fact is bad for an automatic backup. Does VDR have a special function for those cases or is something like this already known? It would be no problem, to shutdown the servers for building snapshots on Saturday or Sunday. Can VDR initiate a shutdown before starting the backup process? Otherwise I must try to use scripts, but that wouldn't be so nice. Thanks a lot for your help.

  Read the article

• Route web traffic through a separate iterface

  - by tkane

  I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Can we do a DNSSEC 101? [closed]

  - by PAStheLoD

  Please share your opinions, FAQs, HOWTOs, best practices (or links to the one you think is the best) and your fears and thoughts about the whole migration (or should I just call it a new piece of tech?). Is DNSSEC just for DNS providers (name server operators)? What ought John Doe to do, who hosts johndoe.com at some random provider (GoDaddy, DreamHost and such)? Also, what if the provider's name server doesn't do automatic signing magic, can John do it manually? In a fire-and-forget way, without touching KSKs and ZSKs rollovers and updating and headaches?) Does it bring any change regarding CERT records? Do browsers support it? How come it became so complex? Why didn't they just merged it with SSL? DKIM is pretty straightforward, IANA/IETF could've opted for something like that. (Yes I know that creating a trust anchor would be still problematic, but browsers are already full of CA certs. So, they could've just let anyone get a cert for a domain for shiny green padlocks, or just generate one for a poor blue lock, put it into a TXT record, encrypt the other records and let the parent zone sign the whole for you with its cert.) Thanks! And for disclosure (it seemed like the customary thing to do around here), I've asked the same on the netsec subreddit.

  Read the article

• OpenVPN bridge network from routed clients

  - by gphilip

  I have the following setup: subnet 1 - 10.0.1.0/24 with a machine used as NAT and also running an OpenVPN client subnet 2 - 192.168.1/24 with an OpenVPN server (the server in subnet 1 connect here) subnet 3 - 10.0.2.0/24 that uses the NAT machine (subnet 1) to access the internet, so all non-local traffic is routed there to the eth0 interface The OpenVPN client creates the tun0 interface and appropriate routing so that I can access machines from 192.168.1/24 [root@ip-10-0-1-208 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... Connected to 192.168.1.186. Escape character is '^]'. [root@ip-10-0-1-208 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.1 10.8.0.5 255.255.255.255 UGH 0 0 0 tun0 10.8.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 169.254.169.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.0.0 10.8.0.5 255.255.0.0 UG 0 0 0 tun0 However, when I try the same from subnet 3, it can't reach that machine. [root@ip-10-0-2-61 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... I suspect that it's because subnet 3 is routed to eth0 on the NAT machine in subnet 1 and it cannot jump to tun0. What's the easiest way to resolve it? I don't want to use iptables. I can't change the routing from machines in subnet 1 because it's done in AWS and so it works only with specific interfaces. Also, the NAT machine gets its IP with DHCP and so bridging is a bit complicated. IP forwarding is set on the NAT machine [root@ip-10-0-1-208 ~]# cat /proc/sys/net/ipv4/ip_forward 1 Thank you!

  Read the article

• VMware Workstation Bridged Network Host UnReachable

  - by user2097818

  VMware Workstation 7 on Win7-64 (Home Premium). I have confirmed this on any guest running on this machine (from winxp to debian). I am using a bridged network connection for my guests (Automatic on VMnet0). All of the network configuration is done with DHCP (including on the host). Problem What I can not do: Ping my host machine from inside any VM. (either shows me "Destination Host Unreachable" or will just timeout) What I CAN do right after power up, with no problems at all. I can connect to the internet from inside the VM I can ping my router from inside the VM I can ping other machines on my network from inside the VM Other machines can ping the VM Other machines can ping the host My host machine can ping the VM (this one is important. read further) Details So I have my router assigned as 192.168.2.1/255.255.255.0, and the router provides the DHCP service (and it seems to be doing so successfully). There are no IP conflicts on the network that I am aware of. All Gateways and Subnet masks are appropriate and matching. My entire workshop is on one single subnet, with one single DHCP server and gateway. There is one method in which I can ping successfully, but it requires an active connection initiated from the host (I start pinging from host to VM). During the period of the active connection, I can successfully ping from VM to host, using explicit IP address. As soon as the host connection is closed, the VM ping starts hanging with the same old messages. My Thoughts This really feels like a firewall problem, but I have turned off all firewalls on host and VM, powered down the network, powered back up, and the problem still persists. And if it was firewall, why would only the IP address associated with bridged VM networks be blocked. I feel as though my host operating system (Win7) is somehow configured incorrectly, or, VMware Workstation is configured incorrectly from the host side. Although I have done my best to put everything in default, I feel like I am missing something silly.

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Win7 Hangs During App Install/Upgrade/Uninstall

  - by JadeMason

  I have a custom built PC that intermittently hangs when installing, uninstalling, or upgrading applications. Technical Specs ASUS P5E w/ WiFi Motherboard Intel Core2 Quad Q6600 Processor 4x 2GB G.Skill DDR2 800 SDRAM ASUS EAH2900XT / Radeon HD 2900XT 512MB Video Card Under normal operation the machine runs reliably, even under heavy load, such as video transcoding. The temperature never gets anywhere near where I would worry about it. However, the machine regularly hangs (complete lockup, no response to keyboard or mouse, no activity on-screen) when either installing a new application, uninstalling an existing application, or applying patches to existing applications or the OS. This is extremely frustrating as this machine is primarily used as a HTPC. Several apps are configured for automatic updates, and these updates sometimes cause the machine to lockup while we are watching content on the PC. In previously investigating this issue, I found one likely problem could be my Logitech Webcam. The Logitech software has a bug that leaves an entry in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ Control\SessionManager\PendingFileRenameOperations Which references the Temp directory. My registry contained this error, so I uninstalled the webcam software and deleted this registry key value. Unfortunately, the machine will still intermittently hang. I've noticed that the hangs always happen when an install/upgrade/uninstall requires elevated privileges (presumably to modify the registry). I can typically get at least one install/upgrade/uninstall to complete after a reboot, but after that it is a game of russian roulette to see if the operation will succeed or hang the machine. The event log is not helpful, as log messages end at the time of the hang, with no record of a warning or error. My only recourse when the machine hangs in this way is to perform a hard reset/power cycle. Any tips on how to further debug this issue are greatly appreciated.

  Read the article

• One Windows Domain workstation can ping gateway but gets no internet access

  - by dindeman

  One of the (Windows XP SP3) workstations of our Windows Domain could not access internet anymore, this problem suddenly happened overnight. The domain controllers (there are three of them) are all running Windows Server 2008. First I compared the output of ipconfig /all on the faulty workstation with the output of a working workstation and it was just fine as it had always been. In particular the default gateway was correct and always remained pingable from the faulty workstation. I guessed that something was wrong with the DHCP service and I restarted the DHCP server service on all of our three DCs as well as the DHCP client service on the faulty workstation. This didn't solve the issue. I then thought of renewing the DHCP lease with ipconfig /release and ipconfig /renew and here is my first question: why did this never work? The same IP address (192.168.0.45) kept being assigned despite all my attempts to renew it (note that all our workstation are getting their TCP/IP automatically.) Even by leaving the domain and changing the computer name the same address was yet again obtained... Anyway I then proceeded to switch the TCP/IP configuration for that machine manually to another free valid IP address (192.168.0.41)... and then the internet access came back! I then cleared any traces of the previous IP in the DHCP leases list and in the DNS tables of our DCs and, after setting back the TCP/IP configuration to 'automatic', finally, the new lease would be granted (192.168.0.41) alongside with the internet access. My second question: what went suddenly wrong with the original IP address?

  Read the article

• Win 7 firewall won't turn on, nor the McAfee firewall. Hit by "Win 7 Anti-virus 2012" trojan. Removed, but a downed firewall is a lasting legacy

  - by PhxTitan

  I caught the Trojan right away, I think, but both my McAfee & Win 7 (x64) firewalls are not able to be engaged/turned on now. MS Error Code 0x80070424 when attempting to turn on Win 7 firewall. No viruses. Swept it with McAfee AV, Malwarebytes Anti-Malware, Microsoft malware removal tools. Followed Microsoft's three courses of alternative actions they posted for instructions for getting the Win 7 firewall back up and on. Nothing. Same error code. The post just said see MS support if those fixes failed. So I removed McAfee altogether. Still Win 7 (professional version) firewall won't come on; and clean of detectable bugs. And I'm fully updated with MS Windows 7 updates as well, which is no longer automatic, that too a legacy of the trojan bug I think. Any thoughts on how to get the Win 7 firewall operational??? And auto updating reengaged?

  Read the article

• How to force the start and end date of a task in Microsoft Project to be on the same day?

  - by Hauke P.

  I have a task called "Interview person A about topic X". The task's duration is set to 2 hours. The start date of the task should automatically be calculated taking dependencies and resource availabilities into account. My question boils down to: How can I force this task to start and end on the same date? Background: In my case, Microsoft Project sets the start date to a Friday at 5pm. As my working hours are set to 8am to 12am and 1pm to 6pm (Mon-Fri), Microsoft Project "splits up" the task at 6pm on Friday and plans to continue it at 8am on the following Monday. However, it does not make any sense to stop the interview on a Friday and restart it on Monday. Therefore the automatic suggestion is not helpful in this case. That's why I'm looking for a way way to force the task to start and end on the very same day. (In my example, I'd like Microsoft Project to delay the start date of the task until Monday 8am as this is the first time slot in which the task "fits in completely".) By the way: I have lots of such cases... for that reason it would be really great if there was a solution that doesn't just deal with this single special case.

  Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >