Search Results

Search found 13518 results on 541 pages for 'graphical interface'.

Page 157/541 | < Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >

• How to setup dhcp3-server to advertise the DNS server the server itself has got from DHCP?

  - by Ivan

  The Ubuntu 10.04 server has eth0 Internet interface configured by means of an ISP's DHCP. At the same time the server has static eth0 LAN interface to which it provides masquerading (NAT) and LAN-internal DHCP service (dhcp3-server). As far as I've understood the manual, I had to hardcode DNS servers to advertise through LAN DHCP with option domain-name-servers in dhcpd.conf. But what if the ISP changes his DNS server IP silently (we use a SOHO-class ISP, so this won't surprise me much)? Can I configure dhcpd to advertise the DNS server the server uses itself, the one gotten by its DHCP client mechanism?

  Read the article

• Connecting via ShrewSoft VPN client means no LAN internet access (Windows 7 64 bit) - any advice please?

  - by iwishiknewmoreaboutnetworking

  I have a Windows 7 64 bit desktop machine which is connected to a LAN. I recently installed ShrewSoft VPN client v 2.1.7 on my machine so that I can connect to a license server hosted by my customer. They are running a Cisco VPN server and I originally tried (unsuccessfully!) to use the Cisco VPN client for Windows 64 bit but the default gateway wasn't being configured correctly after loading in my pcf file. Using ShrewSoft I am able to import the same pcf file, and successfully connect to the machine I need to using the VPN client software. The client machine I need to connect to has IP address 1.52.90.33. The problem is that when I am connected to the customer network using the VPN client application (and after a few minutes) I lose my LAN internet connection. I can only presume that this is because, by default the ShrewSoft VPN client application automatically tunnels all traffic through the VPN connection. I know there is an option to switch off the "Tunnel All" option on the Policy tab of the application and enter a Remote Network Resource (to "Include" or "Exclude") as "Address" and "Netmask" IP addresses however I am not sure what I need to enter here. Here is my ipconfig output before connecting to the VPN (with suffixes blanked out): Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : ***.*** Link-local IPv6 Address . . . . . : fe80::8de3:9dbe:393a:33ba%11 IPv4 Address. . . . . . . . . . . : 150.237.13.17 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.237.13.1 Tunnel adapter 6TO4 Adapter: Connection-specific DNS Suffix . : ***.*** IPv6 Address. . . . . . . . . . . : 2002:96ed:d11::96ed:d11 Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 9: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:2cf9:38c4:6912:f2ee Link-local IPv6 Address . . . . . : fe80::2cf9:38c4:6912:f2ee%12 Default Gateway . . . . . . . . . : Tunnel adapter isatap.***.***: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ***.*** Here is my route print output before connecting to the VPN: =========================================================================== Interface List 11...20 cf 30 9d ec 2a ......Realtek RTL8168D/8111D Family PCI-E Gigabit Ethern et NIC (NDIS 6.20) 1...........................Software Loopback Interface 1 14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 12...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 150.237.13.1 150.237.13.17 2 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 150.237.13.0 255.255.255.0 On-link 150.237.13.17 257 150.237.13.17 255.255.255.255 On-link 150.237.13.17 257 150.237.13.255 255.255.255.255 On-link 150.237.13.17 257 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 150.237.13.17 257 255.255.255.255 255.255.255.255 On-link 12

  Read the article

• XCache permission issue

  - by Guilhem Soulas

  I successfully installed XCache on a Linux server where WHM/cPanel is installed too. However when I go to the admin interface it shows me only the cache for the owner of the folder (= a cPanel account). So I copied the admin interface on another cPanel account of the same server and I'm surprised about the memory allocation because it seems to use the memory I set in php.ini for EACH user. So if set the memory size to 64M and I have 10 users, doesn't it mean that XCache can take up to 640M? It's not the behaviour I want because I can't control the memory in that case! I would like to set 64M only for the entire server.

  Read the article

• How to block all multicast traffic travelling through a Cisco Catalyst 3750

  - by TrueDuality

  Something changed today. I can't seem to track down what, but one of our 3750s decided that it was going to forward all the multicast traffic it saw from the ghost server across every VLAN it has. I've tried writing a simple access group that consists of the following: access-list 100 deny ip any 224.0.0.10 0.0.0.255 access-list 100 permit ip any any I apparently mistakenly assumed that once applied to an interface that it would block all of the multicast traffic on that interface regardless of VLAN. I do not want any multicast traffic flowing through this particular switch to any VLAN or even to stay on the same VLAN beyond this switch. Does anyone have any ideas?

  Read the article

• How can I setup a Firewall without NAT?

  - by SRobertJames

  We have 16 IP addresses from our ISP, and are setting up a SonicWall Firewall. I'd like to have the SonicWall do NAT for the LAN, but act as a firewall only (no NAT) for the servers which are using some of the 16 addresses. How do I set this up? If I set the WAN's subnet to include the 16 IPs, the SonicWall won't route the traffic to the LAN interface. Should I set the WAN subnet to only include the ones we are dedicating for NAT, and then keep the others on the LAN? Related point: How can I set multiple IP addresses for a SonicWall LAN interface?

  Read the article

• Monitor ESXi hosts with Nagios

  - by Kyle Brandt

  Does anyone recommend any methods for monitoring ESXi 4.1 hosts with Nagios? I have looked into SNMP but it seems to be in a pretty sorry state. Net-SNMP does not seem to be included and there is a built it SNMP daemon that I set up. However from the standard MIBs there only seems to really be network interface counters and the VMWare MIBs seem quite useless. Right now I am considering SNMP for the interface speed and trying the plugins listed at http://unimpressed.org/post/96949609/monitoring-esxi-performance-through-nagios . Anyone have a better idea? I would like to monitor the hosts directly, not through something like vCenter.

  Read the article

• having 2 ip's on a debian 7 box

  - by David

  I just installed Debian Wheezy on my homeserver. I want to assign 2 ip's to it on the same network interface, 1 static ip (eth0) and 1 dynamic ip (eth0:1). I know it doesn't make much sense but I need it to test something. I edited my /etc/network/interfaces to be like this: auto lo eth0 eth0:1 iface lo inet loopback iface eth0 inet static address 192.168.178.240 network 192.168.178.0 netmask 255.255.255.0 broadcast 192.168.178.255 gateway 192.168.178.1 iface eth0:1 inet dhcp when I bring up eth0:1 (ifup eth0:1) I get the following error (eth0 works fine) Bind socket to interface: No such device Failed to bring up eth0:1. is it even possible to have a dynamic and static ip on the same network adapter?

  Read the article

• Windows 2003 server RRAS on VPC

  - by Saif

  I'm trying to setup a L2TP VPN server(to give user access on to all my VPN instance) on a Windows 2003 instance running on my VPC. While trying to enable RRAS I'm getting error, "less than two network interfaces were detected on this machine". Eventually it's because there's only one network interface available, the which has private IP. I have elastic IP assigned to this instance as well. But RRAS can't see this. What should I do to RRAS to be able to see the interface with elastic IP?

  Read the article

• Disable ALTQ for internal network traffic

  - by javanix

  I currently have a FreeBSD 8.2 media server set up on my LAN that I use to stream my music from. I also have an SSH login that I use to do file transfers to and from this server remotely. I would like to set up ALTQ (and have gotten this working) to limit my outgoing bandwidth from the server for SSH traffic. However, configuring ALTQ this way is also limiting my internal traffic (and thus interfering with my music streaming) since I am only using a single network interface. Can anyone show me how I would use PF and ALTQ to limit outgoing WAN traffic while allowing all internal LAN traffic to go through unhindered? ext_if="eth0" int_if="eth0" altq on eth0 cbq bandwidth 1Mb queue { std, ssh } queue std bandwidth 80% cbq(default) queue ssh bandwidth 20% cbq(ecn) pass out on eth0 proto tcp to port 22 queue ssh eth0 is my LAN interface, my total WAN bandwidth on my cable connection is 1Mb/s, and my internal network is 10/100.

  Read the article

• Credentials needed for BT line on Netgear router

  - by Bali C

  I have recently bought a new Netgear router to replace my current BTHomeHub as it doesn't support wireless. I did buy a WAP but figured it would be easier to use a router with wireless built in. (It's a modem/router combo). I have got as far as setting up the router on the web interface, but then it asks for a username and password to connect to the net, I can only assume this is for the phone line? I have tried some passwords I could find written down but they don't work, the internet light comes on and then when the creds fail it goes off. I have been on the homehubs web interface and been through all the settings it has to find the credentials it is using which obviously work, but no joy. Is there anything obvious I am missing, or is there a way I can retrieve my settings from my existing router? Any pointers will be very appreciated.

  Read the article

• Remote connection to dynamic public ip & private ip addresses

  - by user51737

  Many times I connected to windows computer which has static public ip address via remote desktop over wan links. I'm wondering how could I connect to the remote computer that has dynamic public ip address & private ip addresses assigned. I've 2 systems at home: xp system-------connected to internet(dynamic public ip) & allowed other users to connected to the internet on the interface. windows vista system--------enabled dhcp on the interface to access internet from xp. How could I remotely connect from my office to the 'vista system'?. If I've a router/modem at my home it may be possible to allow the ports for the system but I don't. Any tips?

  Read the article

• Programtically get the Wireless lan config of a machine and use netsh to setup new profile

  - by Maestro1024

  Programtically get the Wireless lan config of a machine and use netsh to setup new profile I am having trouble getting the netsh command to set the ssid of a new card. I installed the drivers and plugged it in. I see in ipconfig it says the "media is disconnected" (fair enough). I then send the following command netsh wlan connect name=profile1 ssid=myNetwork interface="Wireless Network Connection 2" problem is I get an error "There is no profile "profile1" assigned to the specified interface. What is a profile for a wireless card? What should I set it to? How Can I get my SSID set and connected for the card.

  Read the article

• Access port on machine by connecting to other machine via SSH?

  - by piquadrat

  I have to access my home router's web interface on port 80. Unfortunately, the only way into the network I have at the moment is SSH to another machine on the same network. me ---|---SSH Box----Home Router My Google foo seems to have abandoned me, I couldn't didn't find anything helpful. Any ideas? Thanks! To clarify: I'm not at home right now. I do however have access to one machine on the network (a QNAP NAS) over SSH. I need to access the home router web interface on port 80 from my notebook which is outside of the home network.

  Read the article

• Recording Interfaces for OS X that are supported/work well?

  - by Troggy

  For os x, I would like to know what other audio production/music recording interface type products people have found to work well with os x? I do not want to know about stuff that only works. I want to know about solid products that work well and are supported well by the company when issues arise. I for example have a M-Audio Firewire Solo recording interface. I have found M-Audio to be a company with great mac support for their products and they integrate well with os x features and apple software. Clarification: I am wondering about the recording interfaces themselves, as in the hardware, that are compatible with os x and supported/work/integrate well.

  Read the article

• How to setup a Linux laptop as a MIDI device ?

  - by dugres

  Wich external MIDI interface will work on Linux to use a software sequencer with an external expander.

  Read the article

• windows 2008 server login screen remote desktop

  - by Marki

  how can I access a GRAPHICAL login screen (like on earlier Windows versions, or like VNC) instead of the Username/Password prompt via RDP? I'm asking because we have several servers where we have no passwords but the shutdown/reboot option is given via group policy on the login screen. Thus, instead of having to go the hardware console I'd like to be able to perform reboot/shutdown actions via terminal services. Regards, Marki

  Read the article

• Windows 7 with two network cards doesn't route traffic

  - by Tomek

  I have simple task to do: I have wni7 with two nics.I want to connect another comp(osx) to win7 through second nic to connect it to internet. I already changed the registry. Win7 interface with 192.168.2.1 has no gateway set (no point to do that) OSX interface with 192.168.2.2 has gateway set to 192.168.2.1 I do not add any routes on win7, every thing seems to be already there network on second nic is detected as "undefined network" (probably effect of no gateway) i can achieve any connectivity to internet from OSX only by enabling network connection sharing on nic with 192.168.2.1, but it enables NAT and I'm interested only in pure routing without nat(it's a setup for some research). firewall is off. It seems to me that win7 refuses to forward packets for some reason. Perhaps "undefined network" and NLA service is to blame, although i couldn't find any info about that. Below ascii schematics of my setup: internet<--router(192.168.1.1)<--(192.168.1.1) WIN7 (192.168.2.1)<--(192.168.2.2)OSX Thanks

  Read the article

• NAT : understanding about interconnection

  - by PITCHY

  English version below J'ai 2 routeurs A et B relié en série avec les ip respectives ( 10.0.0.1/30 10.0.0.2/30) sur le routeur A j'ai activé la fonction NAT avec un pool (200.0.0.1 - 200.0.0.15/28). Lorsque je sors je prends donc un ip du pool par exemple 200.0.0.10. Comment ça fonctionne sachant que ma nouvelle ip (200.0.0.10) ne se trouve pas sur le meme réseau que mon interface de destination (10.0.0.2)? English: I have 2 routers A and B, interconnected with a serial connection, with the ip's 10.0.0.1/30 for A and 10.0.0.2/30 for B. On router A NAT was activated with the pool 200.0.0.1 - 200.0.0.15/28. When connection to this router, I get an ip from the pool, for example 200.0.0.10. Knowing my new ip is 200.0.0.10, which is not on the same network as my destination interface (10.0.0.2), how can this work?

  Read the article

• cisco asa query dns external

  - by Alpacino

  my lab network asa firewall below 10.10.10.20 -- ASA --- 192.168.1.10 -- website external my client 10.10.10.20 want to access website external and i create nat nat (inside,outside) static 192.168.1.10 and access list access-list outside-acl extended permit tcp any host 10.10.10.20 eq www access-list outside-acl extended permit tcp any host 10.10.10.20 eq domain access-list inside-acl extended permit tcp 10.10.10.0 255.255.255.0 any eq www access-list inside-acl extended permit tcp 10.10.10.0 255.255.255.0 any eq domain access-group outside-acl in interface outside access-group inside-acl in interface inside when i access to website with domain name it can't access but i access website with ip address it work please help me to solve problem thank you

  Read the article

• Routing based on source address in Windows Server 2008 R2

  - by rocku

  I'm implementing a direct routing load balanced solution using Windows Server 2008 R2 as back-end server. I've configured a loopback interface with the external IP address. This works, I am receiving packets with the external IP address and respond to them appropriately. However our infrastructure requires that traffic which is being load-balanced should go through a different gateway then any other traffic originating from the server, ie. updates etc. So basicly I need to route packets based on source address (external IP) to another gateway. The built-in Windows 'route' command allows routing based on destination address only. I've tried setting a default gateway on the loopback interface and mangled with weak/strong host send/receive parameters on the interfaces, however this didn't work. Is there any way around this, possibly using third party tools?

  Read the article

• Configure FTP Server with two different IP addresses on different subnets and separate NICs

  - by Luke

  I have an FTP server that's on a low bandwidth connection. We want to set it up with a second IP address on a much higher bandwidth connection. I set up the second interface with a static IP address on the faster connection. This unfortunately does not work. I can verify that the second IP address works perfectly when I disable the first IP address. What do I need to do to get two separate interface IP addresses on different subnets working on the same server?

  Read the article

• Music player for ubuntu similar to iTunes

  - by Allwar

  Hi, I really like Itunes as a music player but i can't get it to work in ubuntu so I need another one! functions i want: shuffle, low cpu usage, a friendly interface and free of bugs. (friendly interface = esay to use) why not use rythmbox, well it has bugs, the shuffle button doesn't work because it shuffles the next song after each song. So when i use it it's just a big loop over three different songs! i want the itunes look, like it shuffles once and lets you see in what order the songs will be played. //Alvar

  Read the article

• connecting internet TV modem to repeater router, will it work?

  - by Sandro Dzneladze

  I've internet TV at home, it works via special modem which connects to router via Lan interface. I'd like to move Tv to a room which has no router. so i'd like to use wifi for internet TV. My plan is this, buy another wifi router, set it to repeat sygnal of primary router and attach this TV modem to repeater router via Lan interface. Will this work? I have limited understanding of how internet TV works, so I'm not sure if my strategy will work... does router have to have some special feature to allow this service? will my strategy work?

  Read the article

• Are there any 17-20 inch monitors that support displayport?

  - by WildJoe

  I've got dual monitors now (both 20 inch 1600x1200). After seeing the new eyefinity cards out there (and reading the CodingHorror post on three monitors) I've decided to get a third. It's time to upgrade my video card anyway. Since I don't already have a third monitor and will be buying one new, I figure it'd make sense to buy one that already had a DisplayPort interface so as to avoid the adapter issue. However, I can't seem to find any monitors on newegg that support this (it's not even an option in the power search, and a keyword search turned up only adapters and video cards). A quick google showed me several 30 inchers (like Dell's, but that's way too expensive, and I don't have that much room on my desk even if I had that money) and some 22 inch models. Again, I'm looking for a 17-20 inch with a DisplayPort interface built in. Any suggestions?

  Read the article

• how do I create a bidirectional bridge using iptables

  - by Kolzoi

  Setup: I have a samsung LCD TV that is connected via eth0 to a T41 Thinkpad running Ubuntu 10.10 which is wirelessly connected to the home router. I am trying to get Samsung's remote control app working on my iPad but the app won't allow me to put in an ip address and only discovers the tv if it's on the same subnet as the iPad (lame). So I need the laptop to route packets from eth0 to the wireless interface (wlan0), and I need about 3 ports on the wlan0 interface to be forwarded to the samsung tv. Hopefully all this makes sense. I've been messing around with iptables and samsung is now able to access internet via laptop wireless, but mapping from wlan0 back to the samsung tv is eluding me.

  Read the article

< Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >