Search Results

Search found 22877 results on 916 pages for 'network storage'.

Page 159/916 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

• Disabling RAID feature on HP Smart Array P400

  - by Arie K

  I'm planning to use ZFS on my system (HP ML370 G5, Smart Array P400, 8 SAS disk). I want ZFS to manage all disks individually, so it can utilize better scheduling (i.e. I want to use software RAID feature in ZFS). The problem is, I can't find a way to disable RAID feature on the RAID controller. Right now, the controller aggregates all of the disks into one big RAID-5 volume. So ZFS can't see individual disk. Is there any way to acomplish this setup?

  Read the article

• Why do my Taskbar icons disappear after a reboot

  - by cruz

  W7 Pro 64 bit is networked and configured the reg key %USERPROFILE%\Desktop as [driveletter]:\Desktop. After a power off\power on, it shows all my Desktop icons & Taskbar pinned icons.

  Read the article

• Copy windows shared file from cmd

  - by Bogdan Gusiev

  Is there a downloading tool that supports Windows Shared files and works from command line? Standard copy is getting hanged with no action on my side. Tried wget but seems it doesn't 'eat' the link.

  Read the article

• Is there a small business router that shows bandwidth usage graphs in the admin panel?

  - by Robert Drake

  I support a large number of public libraries that are having their networks upgraded in response to a grant application. These libraries are generally home to between 6-15 computers and have little or no tech services either onsite or contracted remotely. In order to justify current and future purchases, a number of the libraries have requested routers that can provide bandwidth usage graphs that they can show to their managing boards. Is there a small business router that displays traffic graphs in the router administration web interface? The router needs to suppport DHCP and basic firewalling. No other features are required. Further, the reports just need to show overall trends. It is not necessary to show traffic by IP, by protocol/application, or by time of day. They just need an overall week to week, month to month, trend line. I'm familiar with MRTG/PRTG/tools that collect SNMP data from the router, but the libraries don't have the expertise for the configuration. I've considered installing the tomato firmware on some cheap home/home office routers, but if there's a commercial product that can be purchased that would be significantly simpler. Also the library boards would be much more likely to approve the purchase of a commercial product over a 'hacked' one. Any assistance would be appreciated.

  Read the article

• fast way to find network user computer on domain hogging all wan bandwidth

  - by dasko

  i have a network of about 40 domain users and i have huge latency wan issues, like 1400ms for google.com pings. I have noticed that the problem goes away after everyone goes home for the day. I would like to know if i should use something like a hub with wireshark on the router or modem to see if there are any irregular activity. I am open to suggestions but i need to isolate which user has the bug. I am assuming it is either downloads or someone spamming out heavily and not knowing. It would be best to trace to ip number so i can just look into dns and find the pc hostname with the problem? This is the first client i have this problem with so never really needed to address it before but not suprised as users don't actually listen to any best practices that we have suggested. Please help, thanks. just to update, pc's to routers and other computers have ping latency of 1ms so it is right after i hit the wan, using tracert to a web site (random), that i get the massive delay in the responses. As well this is a dsl line with 5mb down and 650kb up (maybe upload saturation?) thanks.

  Read the article

• How can I setup apache+mod_proxy so when I connect to mod_proxy on interface X, it sends the traffic

  - by aspitzer

  We use a service that allots us X number of requests per IP and has allows us to setup 5 IPs with such a limit (I know.. it seems stupid they could not just up the limit 5x on one IP). Pretend I have a linux box with the following address on the internet: 66.249.90.104 - that is an Google IP and not mine... so feel free to try to hack into it :) I setup apache+mod_proxy as a forwarding proxy (ProxyRequests On). i.e. you can setup firefox to use 66.249.90.104:8080 as a proxy, and all firefox traffic comes out as 66.249.90.104. So far so good. Problem: Now I add more alias interfaces so the total looks like this: eth0: 66.249.90.104 eth0:1 66.249.90.105 eth0:2 66.249.90.106 eth0:3 66.249.90.107 eth0:4 66.249.90.108 I run apache+mod_proxy (single apache instance) which binds to all interfaces, but no matter which address I connect to use the forwarding proxy, all traffic goes out to the internet as 66.249.90.104 I have also tried running 5 different apaches, each binding to its own interface only, but that still sends the outbound request through 66.249.90.104. I was hoping to get it to work as follows: I connect to 66.249.90.108 and make a proxy request, and it goes out as 66.249.90.108. I connect to 66.249.90.107 and make a proxy request, and it goes out as 66.249.90.107. etc. Has anyone else had to deal with this issue? The fall back solution would be to just run apache on 5 separate boxes, but I would prefer it to all work on one box. Thanks!

  Read the article

• setup mtu automatically after system reboot

  - by Gopalakrishnan Subramani

  I have issues with slow internet and by changing mtu works fine for me. I use Ubuntu 9.10 64bit system. I have dynamic ip address setup All the time after system bootup, I need to do the following command to make mtu setting take effect. sudo ifconfig eth0 mtu 1492 Are there any way I can set it up using startup program. As you know, sudo prompt me root password.

  Read the article

• DHCP over WiFi on CentOS 6 [closed]

  - by dongle26

  Using CentOS 6 I cannot get my WiFi interface to configure over DHCP. Here is my ifcfg-wlan0: This does not work (although it is correct): DEVICE=wlan0 BOOTPROTO=dhcp ONBOOT=yes HWADDR=xx:xx:xx:xx:xx:xx TYPE=Wireless This works: DEVICE=wlan0 BOOTPROTO=none ONBOOT=yes IPADDR=192.168.0.253 NETMASK=255.255.255.0 DNS1=192.168.0.99 GATEWAY=192.168.0.99 HWADDR=xx:xx:xx:xx:xx:xx TYPE=Wireless I don't want a static IP address, I want a DHCP assigned address. Update: Both of the above configs are correct. Please don't downvote, this really didn't work for me. It must be a bug in CentOS or my wireless driver. See my answer for details.

  Read the article

• Incremental backups from Rackspace Cloud Files to Amazon Glacier

  - by Martin Wilson

  Is there a software product/module (open-source or commercial) that can provide incremental backups from Rackspace Cloud Files to Amazon Glacier? We are looking for something that will provide the following functionality (or achieve the same result, i.e. a cost-effective backup strategy for files stored in Rackspace Cloud Files): Work out which files have been added to or modified in a Rackspace Cloud account (since the last backup). Create a ZIP (or similar) of these files and store them in Amazon Glacier. Keep a record of which files are in which ZIPs. Ideally, restore either a single file or all files from Glacier back into Rackspace.

  Read the article

• Mapping drives on MacOSX (Leopard/Snow Leopard) permanently inside LAN

  - by Shyam

  Hi, How do I "map" shared folders on a Mac, permanently? With map, I do not mean 'connect', but permanently add it to the system so it exists after reboot. Since workstations tend to shutdown, I wonder also the symptoms and cures in case that happens. In Linux, this can be done using the fstab file, but I noticed that volumes are mounted in a different structure than Linux. I need this to backup some workstations, doing a recursive job over a single directory, that should contain the shared folders. I use Terminal to access the main system, so by preference, the solution would be nice that works within a bash shell vs GUI. I can access all folders in Finder. Thanks!

  Read the article

• Headless VirtualBox VM NAT Network

  - by dirt

  I have a remote linux server accessible through SSH only. My goal is to host multiple Virtual Machines on this host server using VirtualBox. The host server has 1 IP address, so NAT will be used to route to the VMs for example 10022 will forward to server1:22 and 20022 will forward to server2:22. I have installed VirtualBox and copied a pre-configured CentOS VM to the host server. I start the VM, but cannot establish a connection to the server for example ssh -p 10022 127.0.0.1 times out. I've tried many things: Method 1: Copied existing .vdi, attached to new VM Method 2: Imported .Ova VM (thought it would help any MAC re-init issues?) NAT network type, tried natnet1 192.168/16 and 10.0/16 VBoxManage modifyvm "hermes.awoms.com" --natnet1 "192.168/16" Port forwarding with and without specifying VM ip in modifyvm --natpf1 command VBoxManage modifyvm "hermes" --natpf1 "guestssh,tcp,,10022,,,22" VBoxManage modifyvm "hermes" --natpf1 "guestssh,tcp,,10022,192.168.0.15,22" I can't see if VM is even booting (VBoxHeadless "hermes" --start & runs with no errors) I can't tell if VM is getting an IP address Is there anything else I can do to get more information from VirtualBox or the VM starting up when the only access I have is SSH?

  Read the article

• My uncle is the family historian. We need to host about 5-15 TB of images and video. Any inexpensive

  - by Citizen

  Basically we have hq scans of thousands of old family photos. Plus tons of family video. We want to host them where we can still have total control over the content and restrict access. I'm a php programmer, so the security is not an issue. What is an issue is finding a host to store 10 TB of data and not be paying a ton of money. We really are not planning on a lot of traffic. Maybe 1-10 visitors a day; family only. Kind of like an online library.

  Read the article

• Determine Users Accessing a Shared Folder Using PowerShell

  - by MagicAndi

  Hi, I need to determine the users/sessions accessing a shared folder on a Windows XP (SP2) machine using a PowerShell script (v 1.0). This is the information displayed using Computer Management | System Tools | Shared Folders | Sessions. Can anyone give me pointers on how to go about this? I'm guessing it will require a WMI query, but my initial search online didn't reveal what the query details will be. Thanks, MagicAndi

  Read the article

• IOmeter Hanging

  - by Xiuhtecuhtli

  am attempting to setup a test bed with 2 server using IOmeter.exe I have IoMeter & Dynamo running on My Manger server @ 10.0.0.3 i have another machine running only Dynamo @ 10.0.0.4 so. on 10.0.0.4 i run "Dyanmo.exe /i 10.0.0.4 /m 10.0.0.3" at this point the Iometer.exe on 10.0.0.3 Hangs and stops responding. Any Thoughts?

  Read the article

• KVM network bridge with two NICs

  - by Eil

  Greetings, I'm trying to set up bridged networking with KVM and am getting nowhere. There are docs and tutorials on the subject, but they all seem to conflict or don't provide enough info. I was wondering if someone can give me a high-level overview of how to get this working. I can probably work out the details myself (configuring the interfaces, adding routes, etc), I just need help on the big picture: how everything is interconnected. I have a RHEL5 server with KVM installed and running. It has two physical NICs, eth0 and eth1 in the same VLAN. I would like to use eth1 for all traffic between the guests and the rest of the network and reserve eth0 for host management, guest migrations, etc if possible. I'm not picky about which one gets the default route, although it would be nice if we could make it eth0. All of the guests will have static IPs. I would prefer that when a new guest is added, the networking configuration only needs to be set from within the guest itself. Basically, I want this: eth0: all host traffic eth1: all guest traffic Open to any other suggestions if this isn't possible or will be kludgy/difficult. Pointers to existing documentation might not be helpful since I've already been though just about everything out there. Thanks for any help.

  Read the article

• Bug in CDP implementation

  - by Suraj

  We are developing a Linux based ethernet switch which has 6 ports. We are done with CDP protocol. I have connected a Cisco device to port 2. When I quiery for the Cisco device, I get the reply and instead of getting lan1 (port 1 - lan0 .. port 6 = lan5), I always get the interface name as eth0. The same is the case for all the ports. What changes are required to get the correct interface name? I will be very thankful for the information. The snap packet is received in the routine snap_rcv() in the file "linux._2.6.XX/net/802/psnap.c"; Regards, Suraj..

  Read the article

• Free FTP Virtual Drive Software for Windows (if not on Linux)

  - by asksuperuser

  Is there something equivalent to WebDrive but free or open source ? Update: I want on Windows if possible and be able to save a file on a virtual ftp drive from any software. I know already I can type "ftp://[email protected]" into an Explorer address as suggested below but that doesn't transform it into a true virtual drive as i cannot save file from notepad for example.

  Read the article

• Since upgrading to Windows 8.1, I can't open any files on a SMB share shared by my OS X Mavericks Mac

  - by Gary

  I have a PC with Windows 8.1 and a Mac with Mavericks. I have a folder on the Mac that is shared with the PC. When I'm on the PC and I try to open a file that is shared by the Mac, such as an ISO file (a disk image), then I get a message saying that I cannot open the file, or the file is in use (it depends on the app/filetype). I have the same problem when I open a video file. Strangely, text files and PDF files are just fine. And if I copy any of the problematic files to the local Windows disk, then I can open them just fine. The specific error messages are: AVI files opened in VLC: "Your input can't be opened. VLC is unable to open the MRL." ISO files opened by Windows Explorer: "Sorry, there was a problem mounting the file." This only started happening after I upgraded to Windows 8.1 on the PC and Mavericks on the Mac. Mavericks upgraded its SMB version from SMB1 to SMB2, so perhaps that is related? Does anyone know what the problem might be, and how I could fix it? Thanks in advance!

  Read the article

• File open fails initially when trying to open a file located on a win2k8 share but eventually can su

  - by Ruddy Douglass

  Core of the problem: I receive "(0x80070002) The system cannot find the file specified" for roughly 8 to 9 seconds before it can open it successfully. In a nutshell, we have two COM components. Component A calls into Component B and asks for a UNC filename to write to - the filename returned doesn't exist yet, but the path does - it then does its work, creates and populates the file, and tells Component B its done by making another com call. At that point Component B will call MoveFile to rename the file to its "official" name. This code has worked for (literally) years. Its works fine on win2k3. Its works fine when its running on win2k8 and points to a share on a win2k3 server. It also runs fine, if the share is actually located on the same win2k8 machine that the code is running on. But if you run it on win2k8 and point it to a share on a different win2k8 server, it fails. Both Component A & component B exist in their own Windows Service running with as a domain admin account. The shares are configured for "Everyone/Full control" in all test environments, similarly so are the underlying folders that the share points to. All machines are in the same domain. During debugging I realized the file actually does exist by the time I get to checking manually for it - after several iterations it occurred to me that the file doesn't "show up" until some delay passes by - so I put in the loop below in component B as shown below: int nCounter = 0; while (true) { CFileStatus fs; if (CFile::GetStatus(tempname, fs)) break; SleepEx(100, FALSE); nCounter++; } This code does, in fact, exit and nCounter is generally between 80 & 90 iterations when it does -- indicating the file "appears" approx 8 to 9 seconds later. Once that loop exits the code can successfully rename the file and all further processing appears to work. I put a CFile::GetStatus in component A immediately before it calls into Component B and that indicates success - it can see the file and get its true size yet the call into component b made immediately after can not see the file until the above indicated delay passes. I have verified the pathnames are precisely the same, even though it would clearly have to be for the calls to eventually succeed after a pause of 8 to 9 seconds... When something like this occurs I always assume there is a bug in my code until proven otherwise, but given (a) this code has executed properly for a very long time and (other than my diagnostic loop added) has not changed, and (b) it works in all environments except the win2k8 - win2k8 share, I'm guessing there is some OS issue in here that i do not understand. Any insight would be helpful. Thanks!

  Read the article

• MediaShield RAID 5 is showing up as 760GB when the actual size is 2.7TB

  - by Ilya Volodin

  I just finished setting up Windows 2003 Server on my new server. And I started setting up a RAID 5 for it. I have 4x1TB Hard Drives. From MediaSheild RAID Utility (at boot time) the RAID size is displayed as 2.7TB. Linux also shows it as 2.7TB. However, in Windows, everything (including Windows Disk Management as well as Windows based MediaShield utility) is reporting only 760Gb. I already tried converting partitioning table to GUID from MBR, because I read somewhere that Windows can only handle up to 2TB MBR tables, that didn't help much. Tried searching for partitioning utilities that I could use, but couldn't find anything free. Formatted the disk as NTFS partition from within Linux, it stop showing in Windows all together, even MediaShield windows utility isn't showing at anymore. Windows is installed on a separate 500Gb hard drive, that's setup not to support RAID. Any ideas?

  Read the article

• Redundant OpenVPN connections with advanced Linux routing over an unreliable network

  - by konrad

  I am currently living in a country that blocks many websites and has unreliable network connections to the outside world. I have two OpenVPN endpoints (say: vpn1 and vpn2) on Linux servers that I use to circumvent the firewall. I have full access to these servers. This works quite well, except for the high package loss on my VPN connections. This packet loss varies between 1% and 30% depending on time and seems to have a low correlation, most of the time it seems random. I am thinking about setting up a home router (also on Linux) that maintains OpenVPN connections to both endpoints and sends all packets twice, to both endpoints. vpn2 would send all packets from home to vpn1. Return trafic would be send both directly from vpn1 to home, and also through vpn2. +------------+ | home | +------------+ | | | OpenVPN | | links | | | ~~~~~~~~~~~~~~~~~~ unreliable connection | | +----------+ +----------+ | vpn1 |---| vpn2 | +----------+ +----------+ | +------------+ | HTTP proxy | +------------+ | (internet) For clarity: all packets between home and the HTTP proxy will be duplicated and sent over different paths, to increase the chances one of them will arrive. If both arrive, the first second one can be silently discarded. Bandwidth usage is not an issue, both on the home side and endpoint side. vpn1 and vpn2 are close to each other (3ms ping) and have a reliable connection. Any pointers on how this could be achieved using the advanced routing policies available in Linux?

  Read the article

• Mac OS X & Linux: mount_nfs: can't access /nfs: Permission denied

  - by MountainX

  I have an Ubuntu 12.04 NFS server and I have an iMac NFS client running OS X 10.6.8. I believe I have everything set up properly, yet I still get this error on the Mac: mount_nfs: can't access /nfs: Permission denied My exports on the Linux server uses the insecure option like this: /export/home/me/ 192.168.100.132(rw,subtree_check,insecure,nohide) Where 192.168.100.132 is the address of my Mac. I have even tried using -o resvport on the Mac (in addition to insecure on Linux) and I still get the same error as above. $ sudo mount -t nfs -o resvport 192.168.100.1:/home/me /Users/me/mount Here is the output of showmount: # showmount -e 192.168.100.1 Export list for 192.168.100.1: /export/home/me 192.168.100.132 .... I have reviewed this similar question: How to mount NFS export on Mac OS X? And I have reviewed this frequently recommended tutorial: http://www.cyberciti.biz/faq/apple-mac-osx-nfs-mount-command-tutorial/ I still can't find a solution. Any ideas?

  Read the article

• Is RAID 5 or SnapRAID the better alternative for a media server raid system?

  - by rubo77

  I am using a raid 5 system for my ubuntu 12.04 xmbc media server with 5 disks. Since the data isn't changing a lot and a total loss wouldn't be so bad, cause I have another backup anyway I am thinking about using SnapRAID It sais: SnapRAID is mainly targeted for a home media center, where you have a lot of big files that rarely change The main advantage for me would be power-saving, cause not all disks have to run all the time. Would you recomment using this? (with a regular resync script once a day)

  Read the article

• Setting request-user on IPP printer in CUPS

  - by Maciej Piechotka

  I need to send a request to CUPS server with the specific request-user parameter - remote_user instead of local_user. How should I set the local CUPS server?

  Read the article

• Why is my Network Connections list empty?

  - by DealerNextDoor

  I'm sure this question has been asked before, but none of the links I have found have worked. I've been trying to find fixes for the past couple of weeks. This all started a few days after I got my router. At first, I thought it was just something that would fix it self. But as usual, it never does. I am trying to update my router's wireless card to try and fix this problem, but I need to get the card's information to update it on the HP website. And since my Network Connections list is empty, I can't get any information about it. So to get around this, I tried to go to 'Manage Wireless Networks', and when I tried to get the properties from there, I get this error: Windows has encounter an error saving the wireless profile. Specific Error: The data is invalid. So, what all can I do to try and fix this? Any help will be appreciated. EDIT: Sorry, forgot to put router info. Router Model: WNR1000v2-V2 Router Maker: NETGEAR Router Firmware Version: V1.0.0.12NA The router is up-to-date on all updates.

  Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >