Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 159/1617 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

  • IBM Tivoli Network Manager IP Edition - Job does not run

    - by Thorsten Niehues
    Since our network discovery takes too long I tried to split the biggest job into two parts. The two parts use the same Perl script but have a different scope. I copied a Job (Agent) doing the following: Copied the .agnt file Copied the associated perl script The problem is that one or the other job (changes randomly) does not run. The Disco Process will fail eventually. In the log of the job which does not run I see the following error message: Wed Jul 18 08:48:54 2012 Warning: Failed to send on transport layer found in file CRivObjSockClient.cc at line 1293 - Client My_MacTable_Cis is not connected to service Helper How do I fix this problem?

    Read the article

  • All traffic is passed through OpenVPN although not requested

    - by BFH
    I have a bash script on a Ubuntu box which searches for the fastest openvpn server, connects, and binds one program to the tun0 interface. Unfortunately, all traffic is being passed through the VPN. Does anybody know what's going on? The relevant line follows: openvpn --daemon --config $cfile --auth-user-pass ipvanish.pass --status openvpn-status.log There don't seem to be any entries in iptables when I enter sudo iptables --list. The config files look like this: client dev tun proto tcp remote nyc-a04.ipvanish.com 443 resolv-retry infinite nobind persist-key persist-tun persist-remote-ip ca ca.ipvanish.com.crt tls-remote nyc-a04.ipvanish.com auth-user-pass comp-lzo verb 3 auth SHA256 cipher AES-256-CBC keysize 256 tls-cipher DHE-RSA-AES256-SHA:DHE-DSS-AES256-SHA:AES256-SHA There is nothing in there that would direct everything through tun0, so maybe it's a new vagary of Ubuntu? I don't remember this happening in the past.

    Read the article

  • Starting and stopping X11 and LXDE from command line

    - by Radian
    I have a Raspberry Pi with Debian Wheezy (Raspbian) and so far I've managed to learn quite a lot about Linux just playing around, but I have a few questions for all you seasoned Linux pros out there. 1) From command line, if I execute startx, X11 will launch followed by LXDE. If I had a monitor connected, I'm imagining I would see a transition from command line to the desktop environment. Can I launch X11 first with x, then start LXDE on top of X11 afterwards with /etc/init.d/lxdm start (is this correct?) and get to the same result as startx? 2) Instead, let's say I executed /etc/init.d/lxdm start alone, would X11 start automatically (since LXDE relies on X11)? 3) From desktop, if I CTRL+ALT+F1 to get back to command line, then I should be able to shutdown LXDE using /etc/init.d/lxdm stop. Does X11 automatically close with the termination of LXDE? 4) What is the proper/safe way to shutdown X11? Thanks

    Read the article

  • Connectiong adsl router/modem and router with bridgemode

    - by Zvonko Telefonko
    I have one adsl modem/router which is not "top" of the line and it lack allot of options which I need. I was able to acquire one Cisco router recently which has all options that I need ( like DMZ, VPN, port forwarding, etc). I'm interested, if I connect the old modem/router to new Cisco router using bridge mode, will I be able to use all the features on the Cisco? For instance, the old router is lacking of port forward options. Does this mean that I will not be able to use port forwarding on Cisco router either or, since I will be using bridge mode, this will not affect Cisco router and it will work as the modem is in him? thank you

    Read the article

  • Finding X on Excel scatter plot/trend line

    - by Wilka
    If I have some data in an scatter plot in Excel, e.g. X Y 1 10 2 20 3 30 4 40 5 50 and I want to find the Y value for X = 10, or X=3.5, or whatever (obviously this is a simplified example) I've been doing the following: Add a trend-line to the scatter plot data Format the trend-line to one that fits the data (linear in this case) Display the equation for the trend-line on the chart Type the equation into an empty cell, replacing x with a cell reference. E.g. "=10*A1" then put my X value into the cell A1 Is there a better way of doing this with Excel? It's quite a few steps, and fairly repetitive. Or maybe Excel is just a poor choice of application for doing this? (I'm using Excel 2007)

    Read the article

  • create print server port via command line error Win 8

    - by Benjamin Jones
    I need to create a Print Server Port via commandline in Windows 8 Per Google search I should be using prnport.vbs script to do so: cscript c:\Windows\System32\Printing_Admin_Scripts\en-US\prnport.vbs -a -s \\192.168.113.253 -r Xerox_192.168.113.253 However I get this error: ** Unable to connect to WMI service Error 0x800706BA The RPC Server is unavailable. ** I looked at local services and both RPC and WMI services are started . Also I made sure add remote admin rule to Windows Firewall via command line without success!: netsh advfirewall firewall set rule group="windows management instrumentation (wmi)" new enable=yes netsh advfirewall firewall set rule group="remote administration" new enable=yes NOTE: If I use the GUI to create the print server port then add the printer via command line: rundll32 printui.dll,PrintUIEntry /if /b "Xerox WorkCenter 7535" /F C:\Windows\Inf\WC7545-7556_PCL6_x64_Driver\x2DNORX.inf /r "Xerox_192.168.113.253" /m "Xerox WorkCentre 7535 PCL6" THE PRINTER IS SUCCESSFULLY ADDED. So its NOT the printer it self! So how can I successfully add a print server port via command line? Thanks

    Read the article

  • VoIP - need setup ip network with our SIP operator

    - by evgeniy.labusnkiy
    Need to make next one: for ex i'm now in UAE, but i need to make a call to my girlfriend who is in Ukraine. I need to find the way how can i make the connection to my home router and make the call from VoIP gateway using my standard phone network in Ukraine. I have some imagination about this, to do like this: Connect to router or VoIP gateway (how? soft?) using inet - Gateway make a call using standard phone line in my country. Any ideas? Best practice? What devices i need to make this? Pay attention that i don't want to use any SIP providers. Thats a lot!

    Read the article

  • ISP Load Balancing with ISA 2006

    - by Bill Best
    I understand that ISA 2006 has an integrated Network Load Balancing feature. We also recently acquired a second internet line through a second service provider. I know it is possible to purchase a NLB router for using both incoming lines but this is not the route we would like to take if at all possible. Thus, is it possible to have two ISA 2006 servers each with there own external connection, Load balanced to be viewed as one gateway? My thought was to have two ISA servers each with three NICs, one external, one internal and one for cross communication. I am under the impression that this should work but was hoping someone else has had experience with it.

    Read the article

  • How do you confirm network adapter is gigabit capable?

    - by StrandedPirate
    Upgrading my network to gigabit speeds and don't know how to determine if the NIC in one of the systems is capable of gigabit speed. The documentation from the manufacturer states this: Network adapter 10/100/1000 Ethernet LAN on system board However when I go to the properties of the NIC under Speed & Duplex my only options are: 10 Mb Full 10 Mb Half 100 Mb Full 100 Mb Half Auto Is there a command line I can run that will give me more detail about the NIC? Windows 7 x64 OS New Info: The new switch I just bought has a light to indicate 1000Mbps. I can tell from the light that this NIC is indeed negotiating at 1000Mbps but I'd still like to know how to determine this from the console in windows.

    Read the article

  • How to share internet connection on Mac os x to Virtualbox vm's using Host-only

    - by redben
    In one line : is the following possible : Airport <- osx bridge - vbox-Host-only - vm's On a mac os x, i have virtual box with a virtual machine. For now i have configured 2 interfaces for my virtual machine eth0 is normal bridge for my vm to acces the internet (when airport is connected) eth1 is set to host-only so i can access my vm from the host when there is no wifi/aiport is down. So basically it's like Adapter 1 when there is Wifi, Adapter 2 when there is not. I'd like to have only one configuration to make it simpler. I thought i could just keep the Host only configuration, and on the host (os x) go to internet sharing and select "share from airport" to vboxnet0 (the vb virtual interface). Only to find out that vboxnet0 dosn't show up in the interfaces list on os x preferences. I know that on a linux host you could install something called bridge-utils and use that to bridge the two insterfaces. Is there any thing like that for Mac ?

    Read the article

  • Wireless internet connection connects but internet does not work (no packets received). Wired does.

    - by Rodney
    When I connect my PC via ethernet cable to my ADSL router it works fine. When I connect via Wireless it connects and the internet will work for a random amount of time and then stop working. It stays connected with a strong signal but no packets are received. My laptop/iphone are right next to it and wireless works fine. If I open the Wireless USB status, it says it is connected to my SSID with full strength (54 mps - I am 3 meteres away from my router) and the activty shows as Packets 594 SENT and 105 RECEIVED (this goes up VERY slowly) I have tried the following: Turned off anitvirus and firewall completely. Tested the wifi signal- I am writing this on my laptop which is next to my PC and also has full wifi strength. Tried a different wireless adapter - I dug out an old PCI wireless card - it does the exact same thing. Compared all wireless settings to my laptop. I can ping google.com and it replies (sometimes with packet loss) When I reboot the PC it will connect for a minute or two (random time) and then just stops again. I tried Firefox, IE etc. no joy I have updated all latest versions (Netgear WG111v2) and drivers Checked Event Log - nothing unusual Ping the router (and even connect as admin for the few minutes when the internet does work) Changed the MTU down to 1200 using DrTCP Checked Device Manager for conflicts - none. I ping the router from the PC (192.168.0.10 - 192.168.0.1) and it replies with 4 packets. BUT, on my router admin page (which I access via http on my laptop wirelessly) - if I ping 192.168.0.10 all packets timeout (pinging my laptop 192.168.0.12 works fine) My router admin page shows the leased IP address for 192.168.0.10 (ie it is definitely talking to the router initially) Now I am out of ideas - please help. I think it is an OS/Software issue as I have tried 2 different wireless adapaters (PCI and USB) with the same result but all other wireless devices work fine around mine). It's not the firewall. It is getting assigned an IP address correctly (my PC gets 192.168.0.10, my laptop is .12) It is assigned by DHCP. As soon as I plug in the ethernet cable it all works fine. Repairing the adapter sometimes helps but it will always stop working after a random time. The wireless adapter always shows as connected with Excellent signal but the internet does not work. I am running Windows XP SP3 and have tried a Netgear WG111v2 USB adapter. Thanks in advance! UPDATE: The internet seems to be working, it is just either sending packets too small or slow to work (some small pages load bits of them very slowly but then hang). XP seems to have a networking diagnostic app - here is the output: Last diagnostic run time: 08/30/10 08:16:38 IP Configuration Diagnostic Invalid IP address info Valid IP address detected: 192.168.0.10 IP Layer Diagnostic Corrupted IP routing table info The default route is valid info The loopback route is valid info The local host route is valid info The local subnet route is valid Invalid ARP cache entries action The ARP cache has been flushed Gateway Diagnostic Gateway info The following proxy configuration is being used by IE: Automatically Detect Settings:Disabled Automatic Configuration Script: Proxy Server: Proxy Bypass list: info This computer has the following default gateway entry(ies): 192.168.0.1 info This computer has the following IP address(es): 192.168.0.10 info The default gateway is in the same subnet as this computer info The default gateway entry is a valid unicast address info The default gateway address was resolved via ARP in 1 try(ies) info The default gateway was reached via ICMP Ping in 1 try(ies) info TCP port 80 on host 65.55.12.249 was successfully reached info The Internet host www.microsoft.com was successfully reached info The default gateway is OK DNS Client Diagnostic DNS - Not a home user scenario info Using Web Proxy: no info Resolving name ok for (www.microsoft.com): yes No DNS servers DNS failure HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Passive): Successfully connected to ftp.microsoft.com. info HTTP: Successfully connected to www.microsoft.com. warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out error Could not make an HTTPS connection. info Redirecting user to support call WinSock Diagnostic WinSock status info All base service provider entries are present in the Winsock catalog. info The Winsock Service provider chains are valid. info Provider entry MSAFD Tcpip [TCP/IP] passed the loopback communication test. info Provider entry MSAFD Tcpip [UDP/IP] passed the loopback communication test. info Provider entry RSVP UDP Service Provider passed the loopback communication test. info Provider entry RSVP TCP Service Provider passed the loopback communication test. info Connectivity is valid for all Winsock service providers. Wireless Diagnostic Wireless - Service disabled Wireless - User SSID action User input required: Specify network name or SSID Wireless - First time setup info The Wireless Network name (SSID) to which the user would like to connect = RodSof Wifi. Wireless - Radio off info Valid IP address detected: 192.168.0.10 Wireless - Out of range Wireless - Hardware issue Wireless - Novice user Wireless - Ad-hoc network Wireless - Less preferred Wireless - 802.1x enabled Wireless - Configuration mismatch Wireless - Low SNR Network Adapter Diagnostic Network location detection info Using home Internet connection Network adapter identification info Network connection: Name=Local Area Connection 2, Device=Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC, MediaType=LAN, SubMediaType=LAN info Network connection: Name=Wireless USB, Device=NETGEAR WG111v2 54Mbps Wireless USB 2.0 Adapter, MediaType=LAN, SubMediaType=WIRELESS info Both Ethernet and Wireless connections available, prompting user for selection action User input required: Select network connection info Wireless connection selected Network adapter status info Network connection status: Connected HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Active): Successfully connected to ftp.microsoft.com. warn HTTP: Error 12007 connecting to www.microsoft.com: The server name or address could not be resolved warn HTTP: Error 12002 connecting to www.hotmail.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out error Could not make an HTTP connection. error Could not make an HTTPS connection.

    Read the article

  • PXE Boot not working

    - by Nishant
    Please explain the error in this screenshot DHCP Setting: This screenshot was taken after powering off the old comp hence he server interface is shown as the wireless card - it becomes 192.168.0.1 when I connect wires and power up the old laptop to boot via PXE. My scenario is simple. An old laptop and a new laptop . A cross over cable ( that I myself made from CAT 6 cable by cutting it and connecting 4 wires as mentioned in some doc). The new laptop ( tftp server ) has a Wirelss Card ( with which I am browsing and writing this ) . And the cable is connected between laptops . TFTP server ( new laptop details ) Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::f511:3d4a:ca01:122e%16 IPv4 Address. . . . . . . . . . . : 192.168.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.2 Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Achilles Link-local IPv6 Address . . . . . : fe80::99b1:8ae0:9e6c:f300%11 IPv4 Address. . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.1

    Read the article

  • How do I decrypt WPA2 encrypted packets using Wireshark?

    - by Rox
    I am trying to decrypt my WLAN data with Wireshark. I have already read and tried eveything on this page but without any success (well, I tried the example dump on that page and succeeded, but I fail with my own packets). I caught the four-way handshake from another client connecting to the network. My network info is as follows: SSID: test Passphrase: mypass The above info would give this preshared key: 58af7d7ce2e11faeab2278a5ef45de4944385f319b52a5b2d82389faedd3f9bf In Wireshark in the Preferences--IEEE 802.11 I have set this line as Key 1: wpa-psk:58af7d7ce2e11faeab2278a5ef45de4944385f319b52a5b2d82389faedd3f9bf I have tried the different options of "Ignore the protection bit" but none works. What could I have missed?

    Read the article

  • Discover MAC address

    - by Kami
    I've to setup a bunch of server ! I need to discover their mac address with the following situation : MacBookPro >----------< Server I'm directly connected (not behind a router/switch) to the server. I've no clues about the ip address the server is using as default setup. I can't use a display connected to the server displaying its newtwork card config. How can I discover the MAC address of the server network card ? I'm looking for a command line tool. If something exists in MacPort it's also ok !

    Read the article

  • Alternative Methods of Sharing Folders in Windows?

    - by Blaenk
    Hey guys. I'm running Windows 7 and as of now I simply share folders as one usually does in Windows. I then have a MacBook with Leopard (Now Snow Leopard) which I use to connect to my computer to mount the shares by going to Finder, then CMD + K and typing smb://BlaenkPC (The name of my PC) into the address box. This consequently connects to my computer and mounts all of the shares. The problem is that sometimes, if for example I close my MacBook (Which makes it go to sleep) or sometimes even without doing that, the connection somehow drops. Sometimes I close the MacBook and upon re-opening it, everything still works; it's random. It still shows the computer as being connected, but it just shows 'loading' indefinitely. If I hit 'eject' with the intention of re-connecting to the computer, it disappears from the sidebar (The Computer Icon) in Finder, but I cannot re-connect. Activity Monitor (or ps aux, whichever) both show hung instances of umount; one for each share that was mounted. I cannot kill these processes with kill or killall (Yes, even with sudo, and sending signal -9). This has happened to me before, and here is another person who has experienced this. My question boils down to this: Is there an alternative method of sharing folders in Windows, that my Mac can read/understand, that is possibly more reliable and preferably just as fast? I usually use the mounted shares to watch television episodes off my computer, or movies, etc. (In other words, I open them in VLC and they automatically stream from my computer). As far as I can tell, this is a problem with the Samba protocol. I have heard of NFS, but I am not sure if I would have to re-format my drives, or what. I don't mind running a service or daemon to allow the sharing of the folders, I just want it to be done and hopefully in a better way than typical Windows shares through Samba. Usually when I encounter this problem, which is often (read: every day), I have no other option but to restart the MacBook. As I stated in the first question I linked to, shutting down and restarting don't work; I have to manually force the shutdown by holding the power button. I have not modified my installation of Mac OS X in any hackish way, so I doubt it's something with the Operating System, but worst come to worst, I might end up reformatting and doing a clean install to see if that fixes anything, as I am at a complete loss as to what may be causing the problem, and no one else seems to have any idea or care, despite there being quite a few people suffering from this problem, as my research has shown. Any pieces of information that can help are extremely appreciated. You don't have to answer every question on here, but maybe even some insight as to why it might not be possible to kill those hung umount instances for example, or why I may not be able to reconnect using samba (Is it something regarding the way the protocol works?). One thing to note is that I have another computer in the home network that doesn't seem to have this problem. However, it is also running Windows 7 (Note though that I am not using the homegroup feature, but the typical windows sharing feature). My only deduction is that the problem is being caused by the way the Mac (Or Samba implementation, whichever) is handling things. Perhaps it is a limitation.

    Read the article

  • AuthInfoRequired cups overwrites

    - by mooscape
    My problem is basically identical to the following: http://bbs.archlinux.org/viewtopic.php?id=61826 Put simply, I have a machine in ubuntu trying to connect to another ubuntu machine via a network in order to use the printer attached. There is no problem printing until I restart the guest machine. Immediately it overwrites the printers.conf file (under /etc/cups/printers.conf). It always adds the same line: AuthInfoRequired username,password I stop cups and change it to *#*AuthInfoRequired username,password to comment out the command. Start cups. Works great 'til the next shutdown. Then it gets overwritten again. Googling indicates it may be GTK problem and not CUPS, but I have found no permanent solution to date. Any suggestions appreciated ....

    Read the article

  • Monitoring bandwidth/latency/jitter between 2 sites?

    - by TheCleaner
    I have 2 sites connected via an MPLS network and I'd like to do the following: setup a host on each end that can "talk" back and forth between each other and somehow report/log what kind of throughput, jitter, latency, etc. they are experiencing between each other in 5 minute intervals. Something similar to Qcheck but that can be automated. Bottom line is I'm trying to determine if the WAN network is "stable" throughout the day or if something is wrong. We have video conferences between these sites and even at 1024kbps calls we are experiencing delays and jitter. I'm hoping to exonerate the network with some testing.

    Read the article

  • Should I upgrade my LinkSys WRT54GL firmware?

    - by Reid
    I have a LinkSys WRT54GL v1.1 which currently has stock firmware version 4.30.7. I see that version 4.30.14 is available. The router works fine now, and the release notes look uninteresting except for one line in v4.30.9: "Resolves issue with Linux kernel vulnerability". I have remote management turned off. I'm aware of the 3rd-party firmwares but the stock firmware works fine for me at the moment, so I don't have an interest in those. Is the status quo fine or should I upgrade the firmware? (It's a bit of a pain since the config has to be saved and reloaded, and obviously any mucking with firmware is risky.)

    Read the article

  • Crossover LAN connection between Ubuntu And Windows 7 is not working

    - by brett
    my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

    Read the article

  • Web browsing is fast, but downloads are slow

    - by Ricket
    I work for a company on my university's campus, helping with general IT problems and some web development. But lately there has been a problem that has me and my boss completely stumped. We, plus one contractor, make up the entire IT department, so I'm reaching out to you for help. All around the office, we have wall jacks. These collect in a closet down the hall and all plug into a switch. This switch, along with our individual server jacks, plugs into another switch, and that switch plugs into our firewall hardware. Then the firewall is connected out to our campus network. Our campus internet is, well, very fast. I don't know exactly the terms, tiers, etc., but we have thousands of students and downloads can run as fast as 10 MB/s at night; uploads are sometimes even faster. I think we're practically ISP level. In short, I have a lot of faith that it is not the campus side of things that is causing a problem, combined with other evidence I'll mention in a moment. So our symptoms: web browsing is fast. Web pages, images, etc. load instantly. No problems there. But then when I go to download something, the download starts fast but very quickly (a matter of seconds) drops to nearly 0. Often it will actually drop to 0 and time out. This happens with even very small files, 1 MB or less. It smells to me like a QoS sort of thing. I'm not entirely sure, and I wanted to get your opinions first. My boss is hesitant to touch our firewall, much less let me touch it, and it was set up and is managed by a consultant remotely. These problems don't seem tied to a time of the day. I've tried downloads after 5:00 and still the same thing happens. From my desk, I can turn on my wireless adapter and pick up the campus wireless access point. If I unplug ethernet and connect to it, downloads are fast. This adds to my suspicion that it's limited to our company network. Also, a number of weeks ago the consultant upgraded our firewall firmware. Suddenly everything was very fast. I tested with downloads from Sun and speedtest.net and things were blazing fast, as they should be with our campus internet! It was wonderful, and I figured the slow speeds were an old firmware bug. In a matter of days, things steadily declined until they were back to the old symptoms. Oh, and we have antivirus installed on every computer, and we keep it up to date. Though I suppose the possibility is still there that someone could have spyware which is bogging down our internet, in which case what is the easiest/best way to find this out? (maybe this should go in a separate question) Thank you for your patience in reading all of this. Do you have any ideas as to what I can try? Is this something that you've experienced before? What sort of tools or methods can I use to try and diagnose the problem? P.S. everything here is Windows. Windows Server 2003 and 2008 on our servers, and Windows XP on employees' machines. Update: We are submitting a ticket to the university to just take a look and see if they see anything unusual and/or can suggestion methods for us to try and pinpoint our problem. Hopefully they'll be helpful! I'll update this to let you know what goes on. Update again: We found a hub (yes, a HUB) right between our campus connection and our firewall. It had only those two ethernet cables plugged into it, nothing else. After removing the hub, our speeds have jumped up to several mbps. However in talking with the campus, we got them to run a gigabit line to our firewall in place of the 100mbps line. As of friday, we are at about 65 mbps up and down (according to speedtest.net at 8am)!! Go NC State!!

    Read the article

  • My D-Link's Ethernet bridge downlink just got 10-30x slower?

    - by Jay Levitt
    TL;DR: I unplugged my network to move my desk, and now downloading via my DIR-655's Ethernet LAN bridge is 10-30x slower than the Ethernet switch it's plugged into. Background My network is SMC cable modem <-> Cisco firewall <-> Netgear switch <-> D-Link WiFi† | | | | SMC8014 ASA-5505 GS608v2 gigE DIR-655 rev A3 gigE †The DIR-655 is used as an access point, not a router (although what D-Link calls an access point, I'd call a bridge). The "WAN" port is unused; the Netgear connects to the built-in 4-port Ethernet LAN switch, inside the built- in router/firewall. Endpoints: MacBook Pro 17" mid-2010 iPhone 4S Fedora 12 Linux server running reasonably fast dual-Athlon X2, VelociRaptors, etc. All cables are <10 feet, mostly CAT-5e, some CAT-6, all premade. All WiFi endpoints are within three feet of the D-Link. Yesterday I unplugged and rearranged stuff, and now connecting via the D-Link - even through the wired switch, right next to the incoming network cable - is 30x slower than connecting directly to the Netgear switch, on both my MacBook and iPhone. How I'm measuring "slower" I'm mostly using http://speedtest.net, which of course only really measures broadband speeds. I've also installed http://www.speedtest.net/mini.php on my local server, but can't test the iPhone with that. Results Speedtest.net, closest server over Comcast business-class: CONFIG | PING (ms) | DOWN (Mbps) | UP (Mbps) Mac <-> Ethernet <-> Netgear | 9 | 31.6 | 6.8 Mac <-> Ethernet <-> D-Link | 8 | 4.1 | 6.0 Mac <-> WiFi <-> D-Link | 9 | 1.4 | 2.9 iPhone <-> WiFi <-> D-Link | 67 | 0.4 | 1.6 Speedtest Mini on Linux PC: CONFIG | DOWN (Mbps) | UP (Mbps) Mac <-> Ethernet <-> NetGear | 97.2 | 76.9 Mac <-> Ethernet <-> D-Link | 8.2 | 24.2 Mac <-> WiFi <-> D-Link | 1.0 | 8.6 Slow typing in SSH: Mac <-> Ethernet <-> Netgear <-> Linux PC: smooth Mac <-> Ethernet <-> D-Link <-> Linux PC: choppy Note that D-Link upload speeds are normal on broadband, slower locally (but I'd believe that's a D-Link limitation), and always faster than the downloads! Since ssh is choppy just with slow typing, I don't believe it's a throttling-type problem either; that's not a lot of bandwidth. What I've tried Swapping all "good" and "bad" cables Re-plugging "bad" cable from D-Link to Netgear and watching it be the "good" cable pulling cables away from power lines Verify that the Mac auto-detects the D-Link as gigE Try to verify the link speed of the D-Link <- Netgear connection, but the firmware doesn't report that Verify that the D-Link sees no TX/RX errors or collisions Use different Ethernet ports on both Netgear and D-Link Reset the D-Link to factory settings Upgrade the D-Link firmware from 1.21 to 1.35NA, 2010/11/12, the latest Reboot everything at least once On the Mac, disable Wi-Fi during the Ethernet tests, and unplug Ethernet during the Wi-Fi tests Using iStumbler, verify that the D-Link isn't picking overloaded Wi-Fi channels (usually just 1-5 neighbors on my and adjacent channels, average for my apt building) Verify that the only client connected to the Wi-Fi was the iPhone Verify that nothing was being chatty on my network according to the WISH log Enable and disable all sorts of D-Link settings, including forcing WAN auto-detect to gigE So. I don't mind buying a new access point—I wouldn't mind having a dual-link network—but as a guy who's been networking since gated v4 was a drastic rewrite, and who often used physical sniffers in the days before Wireshark, I'm baffled. I hate being baffled. What could I possibly have changed that would result in this? How can I measure it? All I can think of is a static zap—thick carpet, socks, HVAC—but I didn't feel one, and does that really happen anymore? Can I test if it's Ethernet vs. TCP layer slowness? I'm not familiar with modern network utilities; it's hard to Google without hitting "Q: Why is my network slow? A: Is your microwave on?" If I don't get an answer here, will someone big and powerful help me migrate it to serverfault without getting screamed back here? In the words of Inigo Montoya, "I must know." Don't get all Dread Pirate Roberts on me.

    Read the article

  • Bridging LXC containers to host eth0 so they can have a public IP

    - by Vianney Stroebel
    UPDATE: I found the solution there: http://www.linuxfoundation.org/collaborate/workgroups/networking/bridge#No_traffic_gets_trough_.28except_ARP_and_STP.29 # cd /proc/sys/net/bridge # ls bridge-nf-call-arptables bridge-nf-call-iptables bridge-nf-call-ip6tables bridge-nf-filter-vlan-tagged # for f in bridge-nf-*; do echo 0 $f; done But I'd like to have expert opinions on this: is it safe to disable all bridge-nf-*? What are they here for? END OF UPDATE I need to bridge LXC containers to the physical interface (eth0) of my host, reading numerous tutorials, documents and blog posts on the subject. I need the containers to have their own public IP (which I've previously done KVM/libvirt). After two days of searching and trying, I still can't make it work with LXC containers. The host runs a freshly installed Ubuntu Server Quantal (12.10) with only libvirt (which I'm not using here) and lxc installed. I created the containers with : lxc-create -t ubuntu -n mycontainer So they also run Ubuntu 12.10. Content of /var/lib/lxc/mycontainer/config is: lxc.utsname = mycontainer lxc.mount = /var/lib/lxc/test/fstab lxc.rootfs = /var/lib/lxc/test/rootfs lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.veth.pair = vethmycontainer lxc.network.ipv4 = 179.43.46.233 lxc.network.hwaddr= 02:00:00:86:5b:11 lxc.devttydir = lxc lxc.tty = 4 lxc.pts = 1024 lxc.arch = amd64 lxc.cap.drop = sys_module mac_admin mac_override lxc.pivotdir = lxc_putold # uncomment the next line to run the container unconfined: #lxc.aa_profile = unconfined lxc.cgroup.devices.deny = a # Allow any mknod (but not using the node) lxc.cgroup.devices.allow = c *:* m lxc.cgroup.devices.allow = b *:* m # /dev/null and zero lxc.cgroup.devices.allow = c 1:3 rwm lxc.cgroup.devices.allow = c 1:5 rwm # consoles lxc.cgroup.devices.allow = c 5:1 rwm lxc.cgroup.devices.allow = c 5:0 rwm #lxc.cgroup.devices.allow = c 4:0 rwm #lxc.cgroup.devices.allow = c 4:1 rwm # /dev/{,u}random lxc.cgroup.devices.allow = c 1:9 rwm lxc.cgroup.devices.allow = c 1:8 rwm lxc.cgroup.devices.allow = c 136:* rwm lxc.cgroup.devices.allow = c 5:2 rwm # rtc lxc.cgroup.devices.allow = c 254:0 rwm #fuse lxc.cgroup.devices.allow = c 10:229 rwm #tun lxc.cgroup.devices.allow = c 10:200 rwm #full lxc.cgroup.devices.allow = c 1:7 rwm #hpet lxc.cgroup.devices.allow = c 10:228 rwm #kvm lxc.cgroup.devices.allow = c 10:232 rwm Then I changed my host /etc/network/interfaces to: auto lo iface lo inet loopback auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 92.281.86.226 netmask 255.255.255.0 network 92.281.86.0 broadcast 92.281.86.255 gateway 92.281.86.254 dns-nameservers 213.186.33.99 dns-search ovh.net When I try command line configuration ("brctl addif", "ifconfig eth0", etc.) my remote host becomes inaccessible and I have to hard reboot it. I changed the content of /var/lib/lxc/mycontainer/rootfs/etc/network/interfaces to: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 179.43.46.233 netmask 255.255.255.255 broadcast 178.33.40.233 gateway 92.281.86.254 It takes several minutes for mycontainer to start (lxc-start -n mycontainer). I tried replacing gateway 92.281.86.254 by : post-up route add 92.281.86.254 dev eth0 post-up route add default gw 92.281.86.254 post-down route del 92.281.86.254 dev eth0 post-down route del default gw 92.281.86.254 My container then starts instantly. But whatever configuration I set in /var/lib/lxc/mycontainer/rootfs/etc/network/interfaces, I cannot ping from mycontainer to any IP (including the host's) : ubuntu@mycontainer:~$ ping 92.281.86.226 PING 92.281.86.226 (92.281.86.226) 56(84) bytes of data. ^C --- 92.281.86.226 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 5031ms And my host cannot ping the container: root@host:~# ping 179.43.46.233 PING 179.43.46.233 (179.43.46.233) 56(84) bytes of data. ^C --- 179.43.46.233 ping statistics --- 5 packets transmitted, 0 received, 100% packet loss, time 4000ms My container's ifconfig: ubuntu@mycontainer:~$ ifconfig eth0 Link encap:Ethernet HWaddr 02:00:00:86:5b:11 inet addr:179.43.46.233 Bcast:255.255.255.255 Mask:0.0.0.0 inet6 addr: fe80::ff:fe79:5a31/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:6 overruns:0 frame:0 TX packets:54 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4070 (4.0 KB) TX bytes:4168 (4.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2496 (2.4 KB) TX bytes:2496 (2.4 KB) My host's ifconfig: root@host:~# ifconfig br0 Link encap:Ethernet HWaddr 4c:72:b9:43:65:2b inet addr:92.281.86.226 Bcast:91.121.67.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe43:652b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1453 errors:0 dropped:18 overruns:0 frame:0 TX packets:1630 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145125 (145.1 KB) TX bytes:299943 (299.9 KB) eth0 Link encap:Ethernet HWaddr 4c:72:b9:43:65:2b UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3178 errors:0 dropped:0 overruns:0 frame:0 TX packets:1637 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:298263 (298.2 KB) TX bytes:309167 (309.1 KB) Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:300 (300.0 B) TX bytes:300 (300.0 B) vethtest Link encap:Ethernet HWaddr fe:0d:7f:3e:70:88 inet6 addr: fe80::fc0d:7fff:fe3e:7088/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:54 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4168 (4.1 KB) TX bytes:4250 (4.2 KB) virbr0 Link encap:Ethernet HWaddr de:49:c5:66:cf:84 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) I have disabled lxcbr0 (USE_LXC_BRIDGE="false" in /etc/default/lxc). root@host:~# brctl show bridge name bridge id STP enabled interfaces br0 8000.4c72b943652b no eth0 vethtest I have configured the IP 179.43.46.233 to point to 02:00:00:86:5b:11 in my hosting provider (OVH) config panel. (The IPs in this post are not the real ones.) Thanks for reading this long question! :-) Vianney

    Read the article

  • In TCP/IP terms, how does a download speed limiter in an office work?

    - by TessellatingHeckler
    Assume an office of people, they want to limit HTTP downloads to a max of 40% bandwidth of their internet connection speed so that it doesn't block other traffic. We say "it's not supported in your firewall", and they say the inevitable line "we used to be able to do it with our Netgear/DLink/DrayTek". Thinking about it, a download is like this: HTTP GET request Server sends file data as TCP packets Client acknowledges receipt of TCP packets Repeat until download finished. The speed is determined by how fast the server sends data to you, and how fast you acknowledge it. So, to limit download speed, you have two choices: 1) Instruct the server to send data to you more slowly - and I don't think there's any protocol feature to request that in TCP or HTTP. 2) Acknowledge packets more slowly by limiting your upload speed, and also ruin your upload speed. How do devices do this limiting? Is there a standard way?

    Read the article

  • How to monitor the network traffic on a router?

    - by Adi
    Here's my current network set-up: we have 3 users connecting to a Thomson Gateway router (TG585 v8) provided by my ISP. We are connecting over an ADSL line. The problem is that we have a limited data allowance (60GB) and we always exceed it. I would like to monitor how much traffic each computer makes. The best solution would be to install a software on the router (like OpenWRT) which would monitor how much traffic each computer makes. But I couldn't find any replacement firmware that would support my router. The other solution would be to install a software on each machine and then collect all the data at the end of the mount. But that's not a very good think to do. Plus, the users can always shut down the application. Any suggestions?

    Read the article

  • Determining the required depth and specifications for a server cabinet

    - by Bingu Bingme
    I'm trying to understand the considerations ("why") that go into determining the specifications ("what") for a rackmount server cabinet, in order to determine what sort of rack I should purchase for my home use. Since this is for home use, I won't be following certain best practices (eg. hot/cold aisle, not even air conditioning) and may be willing to sacrifice in various areas in order to reduce cost and footprint - but please advise if there are safety concerns or other considerations to note. The most basic specs for a server cabinet are the dimensions (external width x external depth x usable height). Width: commonly 600mm or 800mm (if the use case requires extra clearance around the sides, such as if there is lots of cabling). In my case and most common cases, I'm going to stick with 600mm. Height: Select a sufficiently tall rack to fit my equipment. But how much may I stuff into it? Eg, if there is a 15U rack, can I really populate it with 15U of servers, or should I leave 1U at top and bottom for air circulation? Depth: Racks commonly have external depth of 600mm (network equipment), 800mm, 1000mm, or even longer. I'm trying to see how to fit into the 800mm depth. With reference to http://www.server-racks.com/rack-mount-depth.html, I'm hoping to have the front and rear posts mounted ~ 28.5" (72cm) apart, which would leave only 8cm for front space and rear space. How much rear space (from rear posts to back of rack) do I really need? I won't use cable management arms, so can I mount a 72cm depth server since the power, KVM, network cables won't take up much depth? My most important equipment are all < 60cm depth (4U chassis) and should comfortably fit within the 800mm cabinet. The rest of the equipment are very old 1U servers that range from 65-72cm depth. I might still want to make further use of them, or I might discard them since they are so old. Even if the 72cm servers cannot be powered on in an 800mm rack, I should be able to use them as 1U shelves. But, what server depth can I expect to be able to operate? Or am I forced to upgrade to 1000mm depth racks in order to use any servers deeper than 60cm? With reference to best practices for HP racks, some other specs and installation considerations: There aren't any minimum recommendations for clearance on the sides of the rack. It is recommended to leave 48" front clearance. The 48" front clearance is based on 32" chassis depth, 13" to extend the rack rails and mate the inner/outer rails, and 3" for movement. If I don't use such rails (eg, use shelves instead), it should be sufficient to leave front clearance of chassis depth + 3". It is recommended to leave 30" rear clearance "to provide space for servicing the rack". I'm planning to back the rack into a corner of the room, and wheel it slightly out when I need to access the rear. If the wheeling plan is ok, I still need to know how much rear clearance is required for air circulation and ventilation purposes. Castor wheels and stabilising feet. Since I'm backing the rack into a corner of the room, I'll only be able to set the stabilising feet on the front corners. Thoughts on safety? The rack that I'm considering has front glass doors with side ventilation slits and fully perforated rear doors. I'm hoping this will be a good balance between temperature and noise (only ventilation slits facing out the front, while the rear is facing the walls). Or is the sound of high-rpm fans going to escape through the front slits anyway and destroy my sanity?

    Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >