Search Results

Search found 539 results on 22 pages for 'nguyen quoc hung'.

Page 16/22 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• what's the difference between a Volume and a Partition in Windows 7 diskpart

  - by user170232

  I was trying to follow the Intel guide for setting up iRST (Intel Rapid Start Technology) on my new laptop. The Intel manual says you need to create a *Volume that is as big or bigger than your available memory, set it to a specific id (id=84), then go into the iRST tool and adjust some settings. Looking at the disk manager on the laptop, I see there is already a Partition labeled as "Hibernation Partition" which is a little bigger than the memory in my system. So it looks like iRST was already set up...BUT, it's a Partition, not a Volume. Here's what the manual says to do: (from: http://download.intel.com/support/motherboards/desktop/sb/rapid_start_technology_user_guide.pdf) diskpart list disk select disk x (where x is the disk to use, there's only one disk in this laptop) create partition primary size=X000 (where X000 is the size to create) detail disk (which lists details for the disk. This is where i get hung up) select volume Z (where Z is the *partition you created previously) ** it says the 'detail disk' command will list the volume #, but it doesn't. ** 'detail disk' only lists two "volumes" for Recovery and OS. ** if i do 'list partition', i see the 8 GB *partition labeled as "Hibernation Partition") ** so I can't continue with the following steps: set id=84 override exit The reason I went looking for the manual is because when iRST is enabled in the BIOS, the system won't resume from sleep. When it's disabled, it works fine, but the system goes into (legacy?) Hibernation mode and takes a while to come out of Hibernation. the iRST is supposed to resume from deep sleep very quickly. So, what's the difference between a Volume and a Partition? Should I delete the Hibernation Partition and create a Hibernation Volume? Anyone have any ideas? (if it matters, this is on a Dell XPS 13 with BIOS A08) Thanks! J

  Read the article

• Boot loop that I cannot bypass

  - by lonewaft

  Recently, on a laptop that I've used for a while, I had a strange issue where OS files were corrupted (device manager) and Windows 8 was hung after the login screen, so I reinstalled Windows 7 over the existing Windows 8 installation, and it worked for a couple days. Today, when I tried to use my laptop, it was stuck on a boot loop. Right after the BIOS screen, it would show a flashing underscore, then restart the computer, again and again until I removed the battery. I tried booting to a windows 7 install CD, but the same flashing underscore - reboot sequence happened when I tried. I tried moving the boot priority around (HDD first, CD/DVD first, even USB first) but nothing changed. After about an hour of tinkering with it, I listened to the HDD sounds, and it sounded like the HDD was trying to spin up, but failing (whining noise increasing in frequency that stopped and started in sync with the system restarting). I am planning to replace the HDD, but I'm still confused as to why a faulty HDD would stop the laptop from booting to my install DVD (tried it on a different computer, it booted from that CD fine). Anybody here have any idea why this might be happening?

  Read the article

• Gittornado with Nginx fails to push and pull

  - by Josh Buell

  I'm making a simple website to host git repositories, much like github. I'm using Gittornado to handle git Smart HTTP requests, and it works perfectly locally; I can clone, push, pull, etc... But when I put it behind Nginx, git commands stop working, giving no errors except: "fatal: The remote end hung up unexpectedly" I know that it's Nginx that's causing the trouble because if I open the port that tornado is running on and try my git commands through that (i.e. "git pull \http://mysite.com:8000/myrepository master" instead of "git pull \http://mysite.com/myrepository master" [backslashes added because Server Fault says I have too many links]) everything works as expected. The Nginx access and error logs don't seem to say anything interesting, so I'm reasonably sure that it has something to do with the way Nginx is compressing or chunking the requests/responses, causing git to think there's been an unexpected hangup, but I'm not sure what to do to fix it, since this is my first time with Nginx. My Nginx configuration file is basically a clone of the on found here; I've tried commenting out various likely-seeming options to see if they were causing the problem, but none of them fixed it so I assume there's some default behavior I need to suppress, I'm just not sure which. Any thoughts on how to fix this? Since it works not through Nginx, I'm considering just redirecting git requests to the tornado port itself, but this feels like a hack rather than a clean solution...

  Read the article

• Authenticating Active Directory Users to Mac OS X Mavericks Server L2TP VPN Service

  - by dean

  We have a Windows Server 2012 Active Directory Infrastructure that consists of two domain controllers. Bound to the Active Directory Domain is a Mac OS X Mavericks Server 10.9.3. The server runs Profile Manager and VPN Services. My Active Directory users are able to authenticate to the Profile Manager, but not the VPN. I have found several threads on other forums of other users reporting similar issues, here is just one of many references: https://discussions.apple.com/thread/5174619 It appears as though the issue is related to a CHAP authentication failure. Can anyone suggest what next troubleshooting steps I might take? Is there a way to liberalize the authentication mechanism to include MSCHAP? Here is an excerpt of the transaction from the logs. Please note the domain has been changed to example.com. Jun 6 15:25:03 profile-manager.example.com vpnd[10317]: Incoming call... Address given to client = 192.168.55.217 Jun 6 15:25:03 profile-manager.example.com pppd[10677]: publish_entry SCDSet() failed: Success! Jun 6 15:25:03 --- last message repeated 2 times --- Jun 6 15:25:03 profile-manager.example.com pppd[10677]: pppd 2.4.2 (Apple version 727.90.1) started by root, uid 0 Jun 6 15:25:03 profile-manager.example.com pppd[10677]: L2TP incoming call in progress from '108.46.112.181'... Jun 6 15:25:03 profile-manager.example.com racoon[257]: pfkey DELETE received: ESP 192.168.55.12[4500]->108.46.112.181[4500] spi=25137226(0x17f904a) Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP connection established. Jun 6 15:25:04 profile-manager kernel[0]: ppp0: is now delegating en0 (type 0x6, family 2, sub-family 0) Jun 6 15:25:04 profile-manager.example.com pppd[10677]: Connect: ppp0 <--> socket[34:18] Jun 6 15:25:04 profile-manager.example.com pppd[10677]: CHAP peer authentication failed for alex Jun 6 15:25:04 profile-manager.example.com pppd[10677]: Connection terminated. Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP disconnecting... Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP disconnected Jun 6 15:25:04 profile-manager.example.com vpnd[10317]: --> Client with address = 192.168.55.217 has hung up

  Read the article

• Email test deferred (mail transport unavailable) with ClamAV

  - by dirt

  I'm trying to set up a simple new mail server; when I send a test email to the server the email is getting hung up during delivery (user mapping is found) and the email is never found in /home/user/Maildir/new Here is my maillog after a fresh reboot and test email, there are a few warnings I am unfamiliar with. Can you please point me in the right direction? Oct 25 14:54:57 loki dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Oct 25 14:54:58 loki postfix/postfix-script[1369]: starting the Postfix mail system Oct 25 14:54:58 loki postfix/master[1370]: daemon started -- version 2.6.6, configuration /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: request to update table btree:/etc/postfix/smtpd_scache in non-postfix directory /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: redirecting the request to postfix-owned data_directory /var/lib/postfix Oct 25 14:56:00 loki postfix/smtpd[1455]: connect from mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/smtpd[1455]: 1CF5E20A8B: client=mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/cleanup[1461]: 1CF5E20A8B: message-id= Oct 25 14:56:01 loki postfix/qmgr[1379]: 1CF5E20A8B: from=, size=1788, nrcpt=1 (queue active) Oct 25 14:56:01 loki postfix/qmgr[1379]: warning: connect to transport private/scan: No such file or directory Oct 25 14:56:01 loki postfix/error[1462]: 1CF5E20A8B: to=, orig_to=, relay=none, delay=0.18, delays=0.15/0.02/0/0.01, dsn=4.3.0, status=deferred (mail transport unavailable) Oct 25 14:56:01 loki postfix/smtpd[1455]: disconnect from mail-ob0-f180.google.com[209.85.214.180] master.cf snippets: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd submission inet n - n - - smtpd -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING smtps inet n - n - - smtpd -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING scan unix - - n - 16 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes 127.0.0.1:10026 inet n - n - 16 smtpd -o content_filter= -o local_recipient_maps= -o relay_recipient_maps= -o smtpd_restriction_classes= -o smtpd_client_restrictions= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks_style=host -o smtpd_authorized_xforward_hosts=127.0.0.0/8

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

• How to stop/kill a virtual machine that hangs in "Stopping" state?

  - by SvetP

  Hi, I have a virtual machine that constantly hangs in the “Stopping” state. I’ve red several posts suggesting killing the vmwp.exe process of the machine but I’ve never been able to kill this process neither from the Windows Task Manager nor from an administrative command prompt by using prockill /PID xxxx /F where xxxx was the process ID. The only result that I have is that my machine enters in “Stopping-Critical” state. Even worse, from that point (having a virtual machine hung at stopping) I am unable to manage (stop or start) any other virtual machine on the same host. The only “solution” in that case for me is to stop the Virtual Machine Management Service (vmms.exe) and to restart the physical host. Without first stopping the vmms.exe service my physical host also hangs during the restart. Moreover, there is no any error logged in the Event Viewer. I’ve found some other posts complaining about them problem. On all of them the only suggestion was to kill the vmwp.exe process, which obviously doesn’t work for them too. Can somebody help us with this, pls? Thanks

  Read the article

• MySQL taking a long time to start

  - by Dscoduc

  I'm running Windows Server 2008 with MySQL installed and every time I reboot the server the MySQL Service doesn't start right away. A look into the Windows Eventlog shows that the MySQL Service was hung at startup. Looking at the Services.msc console shows the service state at Starting... Eventually, like 10 minutes, the MySQL Service actually finishes the startup process and the database becomes available for my Wordpress server... I looked at the MySQL .err files and didn't find anything that would indicate a delay in the statup process... Can anyone suggest a way to determine what is causing the delay, and more importantly, how to prevent the delay in the MySQL Startup? UPDATE: Here is the .err log contents from the shutdown to the startup complete. Notice the startup begins at 10:30:00 and the MySQL isn't ready for connections until 10:47:14, a full 17 minutes later: 100322 10:27:06 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: Normal shutdown 100322 10:27:06 [Note] Event Scheduler: Purging the queue. 0 events 100322 10:27:06 InnoDB: Starting shutdown... 100322 10:27:08 InnoDB: Shutdown completed; log sequence number 4 3854351346 100322 10:27:08 [Warning] Forcing shutdown of 1 plugins 100322 10:27:08 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: Shutdown complete 100322 10:30:00 [Note] Plugin 'FEDERATED' is disabled. 100322 10:30:01 InnoDB: Started; log sequence number 4 3854351346 100322 10:47:14 [Note] Event Scheduler: Loaded 0 events 100322 10:47:14 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: ready for connections. UPDATE 2: MySQL is configured as a service (part of the install process, nothing I did) and executes the following syntax (as it appears in the registry): "C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld" --defaults-file="C:\Program Files\MySQL\MySQL Server 5.1\my.ini" MySQL

  Read the article

• Why should one have a secondary DNS server?

  - by Sam Levin

  I'm very confused. I basically understand how DNS works. Here's an example that helps illustrate what I'm having trouble understanding. Right now, I run a small web-server. I use my provider's DNS manager, so I don't have a DNS server hosted on the machine. Let's say for a second, that I don't use my host's DNS, and I decide to set up a DNS server on my server. Hypothetical scenario: my server (entire) server goes down - DNS included. Why do I need backup DNS? If the server is down, who cares if the DNS server is down too, considering that even if I had DNS up (it wasn't on the crashed server), it wouldn't be able to forward requests anyway since the server would be down? Is the point of having secondary DNS, to be able to change the IP addresses that your DNS server points to, so if your webserver was down, you could redirect traffic to a backup? How would you switch to the secondary provider, in the event that your main DNS provider becomes unavailable? Is a backup DNS system basically up all the time? How is it configured? Is it just an exact clone of the DNS server you would have on your server? Do they run simultaneously? Hopefully someone can see what I'm hung up on, and provide some guidance. Thanks

  Read the article

• Vista WHS Client stopped resolving local names

  - by andrewcr

  I’m running Windows Home Server PP2 in my home, with 3 client computers: two XP and one Vista. I have a router that provides my local DHCP and the server has a static IP address. The other day the Vista machine hung, and on reboot stopped resolving local names. It will show the green home server client icon in the system tray, but if I attempt to log in to the console, I get a “This computer cannot connect to your home server” message. If I ping the server name from the command line, it does not resolve, and gives a “could not find host” message. Oddly enough, if I browse the network, I can see the server, but double clicking on it fails. The other machines on the local network have no problems seeing the server, and the Vista machine has no problems resolving names from the internet, it just can’t see any local machines. I’m aware that I can work around this by adding entries to my HOSTS file (it does work), but I’d like this to work the way it’s “supposed” to. I’m an experienced computer user and developer, but not a networking whiz. Can anyone tell me how local name resolution is supposed to work in my environment and/or suggest ways to troubleshoot this? Thanks, Andy

  Read the article

• another "SSH connect to host github.com port 22: Bad file number"

  - by Mariusz

  Hello. I have a problem with my first-time ssh connection. Yes, I've already done yours guides, already tried your "Dealing with firewalls and proxies" article and the problem is still occuring. I am using Win7 32bit, Windows Firewall is disabled, haven't any third-party firewalls, ESET Nod32 Antivirus is not blocking any ports, I am not using any PROXY (neither local proxy) . Here goes the logs: Ordinary SSH connection try C:\Users\Mariusz>ssh -vvv [email protected] OpenSSH_4.6p1, OpenSSL 0.9.8e 23 Feb 2007 debug2: ssh_connect: needpriv 0 debug1: Connecting to github.com [207.97.227.239] port 22. debug1: connect to address 207.97.227.239 port 22: Not owner ssh: connect to host github.com port 22: Bad file number NCAT connection try C:\Users\Mariusz>ncat github.com 22 Strange connect error from 207.97.227.239 (10013): No error 10013 = WSAEACCES I think that method called "smart-http-support" won't be usable for me because I haven't created repo yet. I have just GIT INIT locally, and finished at step GIT PUSH, which returns the same: ssh: connect to host github.com port 22: Bad file number fatal: The remote end hung up unexpectedly corkscrew method (first article from yours guide) . While PUTTYing (with pageant in bg), after inputing login - an error is occuring (MessageBox): Disconnected: No supported authentication methods available And in terminal such message is printing out: Server refused our key Key I have generated correctly, using ssh-keygen. I tried not method by editing ~/.ssh/config yet because I had thought that because I haven't PUSHed anything to my remote repo so I won't be able to CLONE anything. Method called ssh-forwarding is not for my, cause it "requires access to an external ssh server" and I haven't any at this time. What else could I do? Thanks in advance for any help. Mariusz.

  Read the article

• Ubuntu Server mdadm drbd ocfs2 kvm hangs under heavy file reading

  - by Stefano Annese

  I have deployed four ubuntu 10.04 server. They are coupled two by two in a cluster scenario. on both sides we have software raid1 disks, drbd8 and OCFS2 and on top of it some kvm machines run with qcow2 disks. I followed this: Link corosync is just used for DRBD and OCFS, the kvm machines are run "manually" When it works is fine: good performances, good I/O, but at a given time one of the two cluster started hanging. Then we tried with just one server turned on and it hangs the same. It seems to happen when an heavy READ in one of the virtual machines occurs, that is during rsyn backup. When the fact occurs the virtual machines are not reachable any more and the real server responds with good delay to the ping but no screen and no ssh is available. All we can do is force shutdown (hold the button) and restart and when it turns on again the raid on which relay drbd is resyncing. All the time it hangs we see such fact. After a couple of week of pain on one side this morning also the other cluster hung, but it has different moteherboard, ram, kvm instances. What is similar is reading for rsync scenario and Western Digital RAID Edistion disks on both side. Can anybody give me some input to solve such issue?

  Read the article

• Using git through cygwin on windows 8

  - by 9point6

  I've got a windows 8 dev preview (not sure if it's relevant, but I never had this hassle on w7) machine and I'm trying to clone a git repo from github. The problem is that my ~/.ssh/id_rsa has 440 permissions and it needs to be 400. I've tried chmodding it but the any changes on the user permissions gets reflected in the group permissions (i.e. chmod 600 results in 660, etc). This appears to be constant throughout any file in the whole filesystem. I've tried messing with the ACLs but to no avail (full control on my user and deny everyone resulted in 000) here's a few outputs to help: $ git clone [removed] Cloning into [removed]... @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: UNPROTECTED PRIVATE KEY FILE! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ Permissions 0660 for '/home/john/.ssh/id_rsa' are too open. It is required that your private key files are NOT accessible by others. This private key will be ignored. bad permissions: ignore key: /home/john/.ssh/id_rsa Permission denied (publickey). fatal: The remote end hung up unexpectedly $ ll ~/.ssh total 6 -r--r----- 1 john None 1675 Nov 30 19:15 id_rsa -rw-rw---- 1 john None 411 Nov 30 19:15 id_rsa.pub -rw-rw-r-- 1 john None 407 Nov 30 18:43 known_hosts $ chmod -v 400 ~/.ssh/id_rsa mode of `/home/john/.ssh/id_rsa' changed from 0440 (r--r-----) to 0400 (r--------) $ ll ~/.ssh total 6 -r--r----- 1 john None 1675 Nov 30 19:15 id_rsa -rw-rw---- 1 john None 411 Nov 30 19:15 id_rsa.pub -rw-rw-r-- 1 john None 407 Nov 30 18:43 known_hosts $ set | grep CYGWIN CYGWIN='sbmntsec ntsec server ntea' I realize I could use msysgit or something, but I'd prefer to be able to do everything from a single terminal Edit: Msysgit doesn't work either for the same reasons

  Read the article

• How do I create a "here document" within a shell function?

  - by BenU

  I'm working my way through William Shotts Jr.'s great The Linux Command Line on my Mac OSX 10.7.5 system. 90% of the linux that Shotts covers is close enough to Darwin that I can figure out or GTEM to figure out what's going on. I've made it to chapter 27 on "Writing Shell Scripts" and am getting hung up creating "here files" within a function. I get an syntax error: unexpected end of file error when I include the following function: report_uptime () { cat <<- _EOF_ <H2>System Uptime</H2> <PRE>$(uptime)</PRE> _EOF_ return } The error goes away if I use the following function placeholder: report_uptime () { return } Also, elsewhere in the script, outside of a function I use the cat << _EOF_ format to create a "here file" with no trouble: cat << _EOF_ <HTML> <HEAD> <TITLE>$TITLE</TITLE> </HEAD> <BODY> <H1>$TITLE</H1> <P>$TIME_STAMP</P> $(report_uptime) $(report_disk_space) $(report_home_space) </BODY> </HTML> _EOF_ If anyone has any idea what I'm doing wrong I would be grateful!

  Read the article

• Why won't this script accept any arguments?

  - by Nate Wagar

  I'm trying to write an SVN post-commit hook and, strangely, am getting hung up on what should be the easiest part. The Script: set REPO="$1" set REV="$2" set SVNBIN="/opt/CollabNet_Subversion/bin/" set SSHBIN="/usr/bin/ssh" set HOST="staging.domain.net" set timeout=30 set USERNAME="svn-usr" set E_NO_CONNECT=2 set E_WRONG_PASS=3 set E_UNKOWN=25 set CHANGED=`"$SVNBIN"svnlook changed --revision $REV $REPOS` echo "Here are changes: $CHANGED" >> /var/svn/repos/www/logs/testing echo "Command: $0; Repo: $REPO; Rev: $REV; Total: $#" >> /var/svn/repos/www/logs/testing set PROJECT "" Yet when I call it, it doesn't seem to be seeing the arguments I pass to it: /var/svn/repos/www/logs> sudo ../hooks/post-commit /var/svn/repos/www 33 svnlook: missing argument: --revision Type 'svnlook help' for usage. /var/svn/repos/www/logs> cat testing Here are changes: Command: ../hooks/post-commit; Repo: ; Rev: ; Total: 1 This is on a Solaris 10 SPARC box. I'm a bit of a script newbie, but shouldn't this be really easy??

  Read the article

• Why can't I boot in to Windows Recovery Environment to fix my HDD or salvage my data?

  - by Kevin

  I've been trying to get in to WindowsRE to salvage the files on my Sony Vaio laptop after it failed to load Vista (it finally, consistently displays "Error loading operating system" after months of such intermittent failures, usually rectified via restarts or utilizing Startup Repair or CHKDSK from WindowsRE) . The problem is, after successfully accessing it once after this failure (and many times before over the course of the laptop's life), I can no longer get it to load. During the last successful access (right after the failure), I ran startup repair, which itself failed and notified me that the boot sector was corrupt. I attempted to head in to Sony's proprietary recovery tools menu, which is accessible from WindowsRE when it is loaded from the recovery partition or recovery disk, however it hung. I have since been unable to access the recovery environment after restarting, using any of these methods: Access via the recovery partition (pressing F10 on boot) Access via recovery DVD (created using the same computer when it was healthy) Access via a Windows Vista installation DVD All three methods produce the same results: The computer acknowledges the boot attempt The computer successfully gets passed the "Windows is loading files" screen The computer successfully gets passed the Windows loading screen The computer then stalls at a black screen, while showing HDD activity (via indicator light). After a few minutes, the HDD activity ceases, and after a few more minutes, the over sized cursor that is utilized in WindowsRE appears on the black screen. The actual recovery environment, however, never appears, even after leaving the computer in such a state overnight. What is fustrating is that other bootable utilities, such as SeaTools for DOS and MemTest, boot up and run fine. In running perfectly normally, MemTest was able to produce a plethora of errors utilizing my RAM. I'm inclined to believe the RAM's faultiness may causing the WindowsRE booting to fail. Would this be a valid assumption? If I'm not mistaken, booting from external media utilizes the RAM, so such a reason is plausible, assuming my knowledge of bootloading is correct. Other than that, I can't figure out any reason why all the bootable utilities except WindowsRE run fine. Does anyone know what the problem is, or could be? Any solutions?

  Read the article

• iPhone Lag Terrible - SLOW - What's going on with the iPhone OS?

  - by Sam Schutte

  I've had my iPhone 3G for about a year now, and it seems like at least once a month, it gets bogged down and gets slower and slower - horrible lag when typing, going back to the home screen or opening an app can take 20 seconds. Has anyone else run into this and found "the" solution. What you always read on other boards is to reboot the handset (hold down home and the power button), but that doesn't improve anything for me. I've reinstalled the OS like 5 times now, and I'm getting pretty sick of doing it so often. And I don't buy that it's a hardware issue really, since it works fine for weeks after a fresh install. Anyone have a solution or an idea of what specific actions cause this kind of evident data corruption (OS corruption?) and slowness? Note - I'm looking for specific things here. That is, has anyone done the research to see exactly what on the phone operating system is getting messed up that causes this lag (which is discussed all over the internet, with no working solutions). I don't own a mac, so I can't delve into the guts of the iPhone very well to see what's up with it... Some additional info: Reboots (hold down power/home) and "Sleeps" (slide off) do nothing. Only fresh re-installs help I only have about 15 apps installed - sometimes you see the answer to uninstall apps if you have too many, I'd hope that 15 isn't too many, and even when I've had none installed, it still gets hung up after a period of time. This phone is not jailbroken, and it is running the 3.0.1 release.

  Read the article

• How can I recover a Fedora 12 installation that is showing signs of disk errors?

  - by Bob Cross

  I am currently overseas (i.e., very far from my normal library of tools) and my primary machine that would normally act as the data server in the performance test that we're trying to run is failing to boot to Fedora 12 properly. This is a machine that, as of yesterday, was booting fine. However, this morning, very strange portions of the boot process were complaining with messages such as "unexpected 0x0 in rpcbind" and "bad file descriptor" (I don't have the error in front of me - scavenged a windows installation to get onto serverfault). Eventually, the boot hung for a long time at the NFS service and then brought up what looked like the KDE login screen but neither the mouse nor keyboard functioned. In olden days, I would try to get to a point where I could manage to run fsck and pray that the bad sectors would come back into alignment just long enough for me to scrape the critical data off of the machine. However, now that we live in the future, it seems like our options in situations like this should be a little more varied. Is there a way to recover a Fedora 12 installation with bad disk sectors that won't boot properly? For completeness, I am comfortable working with bootable recovery distros-on-CD and such but I don't know which one is likely to work best with modern Fedora. In the absence of guidance, I'm frantically torrenting the Fedora 12 Live CD and DVD, hoping to try rescue mode before tomorrow morning.

  Read the article

• BTrFS crashhhh?

  - by bumbling fool

  I create a new BTrFS raid10 file system using two 250GB drives and the second partition on a third 80GB drive. I create a subvol and snapshot. I mount the snapshot and start copying 8GB of data to it. It gets to around 1GB and the Desktop disappears and what looks like a non interactive terminal comes up with dump/crash information. I don't have a camera handy or I'd take a picture and post it. It basically looks like stack trace info. CTRL-ALT F7 will eventually bring back the Desktop though but the entire BTrFS portion of the OS is hung and non responsive until I reboot. I've reformated and reproduced this problem 3 times now and I'm about to give up :( I realize it is possible this problem is not entirely BTrFS' fault because I'm on natty which is still alpha. More granular details in case I'm an idiot: 1) Create FS: sudo mkfs.btrfs -m raid10 -d raid10 /dev/sda2 /dev/sdb /dev/sdc 2) Initial temporary mount: mkdir /btrfs && sudo mount -t btrfs /dev/sda2 /btrfs 3) Create subvol btrfs s c /btrfs/vm 4) Create initial snapshot: (optional) btrfs s sn /btrfs/cantremember.snap.something 5)unmount /btrfs and mount /btrfs/vm sudo mount -t btrfs -o subvol=vm /dev/sda2 /btrfs/vm 6) Copy data to subvolume. 7) Balance data across drives: (optional) btrfs f bal <path> (never get to this step 7...) Am I doing something wrong?

  Read the article

• Remove server hangs, gets stuck. How to debug?

  - by bibstha

  I have an vps running on VmWare ESX with Ubuntu 8.04 LTS. It has been running smoothly for the past 3 months, however recently we've notices two strange bugs. a. The server hangs, today was second time. The nature of the hang is very strange. I can ping to the server server, it sends back response fine. However all other services like sshd, apache, mysql etc do not respond at all. When working, telnet servername 22 Escape character is '^]'. SSH-2.0-OpenSSH_5.X Debian-5ubuntu1 And other web services would run fine. When its hung, I can make tcp connections to 22 as well as 80 but receive no response at all. telnet servername 22 Escape character is '^]'. How can I debug this problem? Is there any daemons I can run that will periodically log status? Please tell me as to how to proceed with it. b. The another strange problem is that, of lately I am unable to transfer files larger than around 100KB, smaller files of around 1-2 KB works file. scp anotherserver:filename . or wget http://www.example.com/file would get stuck. There is still around 6GB of space remaining, so I don't think that is an issue. Any pointers where I should look into?

  Read the article

• Exchange 2010 DAG + VMWare HA = no support?

  - by Dan

  We currently have an Exchange 2003 clustered environment (two machine cluster) that we're looking to upgrade to 2010. We recently purchased a VMWare virtualization environment (three Dell R710's with an EMC NS-120 serving up NFS datastores - iSCSI is available) that we wish to use for this new environment. I'm seeing that Microsoft does not support Exchange 2010 DAGs with a virtualization high availability solution (see links below). I would like to utilize the DAG to ensure the data stays available if one host goes down, and HA to ensure that if the physical host goes down, the VM will come back up on the other available host. Does anybody know why MS does not support this? VMWare HA will only restart the VM if it is hung/down - I don't see any difference between this and restarting the physical box if someone pulled the power... Will we only run into issues with support if it has something to do with HA/DAG failover or will they see we have HA and tell us to put it on a physical box even if it has nothing to do with HA? If we disable HA for these VM's will that satisfy them on a support case? Has anybody set up an Exchange 2010 DAG on VMware with HA enabled? Will they have any issues with using an NFS datastore? We have much greater flexibility on the EMC with NFS vs iSCSI, so I would prefer to continue utilizing that. Thanks for any input! http://www.vmwareinfo.com/2010/01/verifying-microsoft-exchange-2010.html Take a look at the second image under "Not Supported" http://technet.microsoft.com/en-us/library/aa996719.aspx "Microsoft doesn't support combining Exchange high availability solutions (database availability groups (DAGs)) with hypervisor-based clustering, high availability, or migration solutions. DAGs are supported in hardware virtualization environments provided that the virtualization environment doesn't employ clustered root servers."

  Read the article

• how to back up data from a machine that keeps hanging

  - by Amit Phatarphekar

  Hello - I have a storage server running opensolaris. But lately its been acting up - it hangs at random times due to some SCSI/ATA related error messages. I've tried to fix it without any progress, so I'm giving up now. The machine keeps hanging every 30 minutes or 1 hr ...sometimes after 4 hrs. Its very unpredictable. So I've decided to just reformat the storage server and start from scratch...maybe I'll just not use solaris and install something else, since the errors are related to solaris running on ATA HDD or something. Question - Before I reformat it, I want to back up some of the important data on it. Like it has a VM with 200 GB disk files, it has a whole bunch of ISOs stored on it etc etc. I'm using a simple scp to copy the files over to a different machine. My issue is that, because the machine hangs....sometimes my file copy is incomplete and I have to start all over again. Lets say I'm trying to copy a 200GB file which takes like 4 hrs....IF the machine hangs before the whole file i copied over...I have to recopy the file from scratch. Is there a solution to copy the files over such that if the machine hangs or network goes down..the copying can resume from where it left off? - like if 50 GB of a 200GB file was copied and machine hung....next time, it'll just continue to copy rest of the amount, instead of starting all over again. Thanks Amit

  Read the article

• Grub hangs at "Starting up ..." when USB flash card reader is plugged in (on Ubuntu Hardy)

  - by Laurence Gonsalves

  I have a PC with Ubuntu Hardy installed. The machine boots fine unless my USB flash card reader (one of those N-in-1 readers by MediaGear) is plugged in at startup. If the reader is plugged in, the boot process proceeds as normal until it gets to the screen that says "Starting up ...". At that point it just hangs forever. To work around this I currently leave the reader unplugged when booting, and then plug it back in after I see that Ubuntu is actually starting. This is annoying though, especially when I reboot the machine (typically for updates), forget to unplug the reader, and walk away only to come back hours later to find the machine hung. My guess is that the presence of the reader is confusing Grub about where to find the kernel. The weird thing is that Grub is on the same drive as the kernel I want it to boot so clearly the drive is still readable even when the flash card reader is plugged in. Is there some way I can tell Grub to never go looking on the flash card reader?

  Read the article

• Sharepoint Central Administration stuck / high CPU usage

  - by johnnyb10

  I'm using WSS 3 and I recently added a new web application to my SharePoint Server. After adding it, I wasn't able to open the Central Administration site. I also noticed that there was a w3wp.exe error (Event ID 1000) in the Event Viewer. The situation now is that the w3wp.exe process is hovering around 50% CPU usage continuously. I installed a program called IIS Peek, and it shows continuous GET requests on the Central Administration site; this happens even if I stop the Central Administration site in IIS. The IP addresses identified in the GET request is my workstation, which is what I used to attempt to access Central Administration after I created the new web application. Can someone explain what's going on and how I might fix it? It seems as if my computer tried to access Central Administration and then it hung, but the page requests that were happening at the time are somehow continuing over and over again. So my two problems are the inability to access Central Administration, and the CPU Usage of w3wp.exe, which I'm assuming are two symptoms of the same problem. I'd like to know if there's anything I can do besides restarting IIS, because we have clients accessing other sites on this server. Thanks.

  Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22  | Next Page >