Search Results

Search found 426 results on 18 pages for 'scsi'.

Page 16/18 | < Previous Page | 12 13 14 15 16 17 18  | Next Page >

• Almost All Logical Volumes Disappeared - Recovery?

  - by Alex

  We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top.

  Read the article

• Low 'Burst Rate' from SATA drive in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks UPDATE: Acorting to this page on the HDTune website... An important parameter of the test is the Burst Rate. This value should always be higher than the maximum transfer rate. A lower value is usually an indication of a configuration problem. So what might be the configuration problem?

  Read the article

• Windows XP VM on VMWare ESXi 4.1 "pausing" / blocked occasionally

  - by FelixD

  We have an issue with Windows XP SP3 VMs on VMWare ESXi 4.1.0 (the free version): They sometimes seem to "pause" for several minutes. This happens rarely (maybe once a month per VM, at least noticed only that often), but still is an issue for us. It happens for three different but similar VMs on three pretty different hosts (different hardware). I have the feeling that the "pausing" is not actually the CPU blocking, but probably the harddisks, but not 100% sure. The servers have one IDE disk (C:) and one SCSI (D:) and it might be either of the two. I have seen scheduled tasks simply not starting for up to 9 minutes and then running normally again with normal speed. They were totally blocked. This is not a load issue, the VMWare hosts have average load and the VMs in question already have reserved CPU resources plus high priorities for CPU and disk. The Windows boxes run mainly MySQL, Tomcat, FileZilla server, Cygwin stuff, Java + R applications, VMWare client, Elusiva Terminal Server pro, Nagios client. Not sure if this might be related with any of that software (e.g. Elusiva). Trying to debug this, there was nothing visible in Windows Event log, other logs in C:\Windows, VMWare events etc. Unfortunately the vmware.log file ends with "Log throttled". We found that we ran into 2 VMWare bugs there: The VMWare client writes lots on bogus messages in the vmware.log, which we now disabled (log level error setting) plus the bug that VMWare does not unthrottle the log (at least so far despite VM reboots). I know there is not much guidance and that may also be the reason why I so far didn't find anything related on the web or on ServerFault, but maybe some of this rings a bell with someone? Or please direct me to what more info to post. I hope that the vmware.logs get unthrottled eventually (can't easily restart the hosts at the moment). Thanks for any input!

  Read the article

• Running Windows 7 physical disk virtualized under Linux

  - by CajunLuke

  I have an existing Windows 7 installation that I'd like to virtualize under Linux. Windows boots fine on Disk A, Linux boots fine on Disk B. (Both disks are SATA.) I can mount the Windows disk when in Linux. I've tried VirtualBox and VMWare Player and neither will allow me to boot from the other disk. VirtualBox doesn't seem to have the option to do so. VMWare Player has the option to have an IDE drive exposed to the virtual environment as a SCSI disk. I've tried that, but it throws the error "Cannot connect virtual device ide1:0 because no corresponding device is available on the host." I've verified that it's pointing to the correct hard drive. I'm willing to try other virtualization products, and I'm not averse to spending a little money to get this to work. I've seen this other question, and it's not a duplicate, as I haven't gotten that far yet. I'm also interested in solutions going the other way (Linux on Windows), but that'd be lagniappe. Gory Hardware Details: Lenovo T410, 2.4 GHz Core i5 (has virtualization extensions), 4GiB RAM, 2x 320 GiB SATA HDD, one in optical bay. Fedora 14 2.6.35.10-74.fc14.x86_64, Windows 7 32-bit.

  Read the article

• How can I undo what I did when I accidentally booted linux host inside itself with VMware?

  - by ThomasGHenry

  Hello, I'm dual booting XP and Kubuntu. I wanted to boot to my existing raw scsi XP partition inside Kubuntu, not a virtual XP instance. I accidentally booted Kubuntu inside itself. I know this is a big mistake, so I interrupted the VM, which saved the state and closed. I rebooted the host and now I can't load the Kubuntu partition at boot time. I get a maintenance shell and the Kubuntu partition is read-only. I am able to boot XP as usual. I removed the HDD and tried to mount it on another computer as an external drive and neither partition (XP or Kubuntu) will be recognized, it just appears to be one device that still mounts and appears empty. From the maintenance shell I can see all the files are still on the Kubuntu partition. How can I undo what I did when I accidentally booted Kubuntu inside itself? Is it a matter of unlocking some files somewhere? how can I do that on a RO filesystem? Thanks!

  Read the article

• Is it safe to format this partition?

  - by xanesis4

  On a ubuntu server I own, I am running out of space. When I ran sudo parted /dev/sda -l to find all available drives, I got this: Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 256MB 255MB primary ext2 boot 2 257MB 1000GB 1000GB extended 5 257MB 1000GB 1000GB logical lvm Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-swap_1: 2135MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2135MB 2135MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-root: 998GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 998GB 998GB ext4 I understand /dev/mapper/server--vg-root is the filesystem, and /dev/sda1 has some stuff related to GRUB. But, what about /dev/sda2 and /dev/sda5? When I tried to mount /dev/sda2, it said that I needed to specify the file system, which according to the table, is nonexistent. So, is it safe to format this with, say ext4 and mount it? Also, when I tried to mount /dev/sd5, it gave me this error: mount: unknown filesystem type 'LVM2_member' I assume it is NOT save to reformat this. If I'm wrong, then that would be great, because I could save some space. Please let me know either way. Thanks in advance! UPDATE: Here is the result of mount: /dev/mapper/server--vg-root on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot type ext2 (rw,acl) /dev/sda1 on /media/hd2 type ext2 (rw)

  Read the article

• OSX / Kernel extensions: problem locating a driver (that extends IOSCSIPeripheralDeviceType00)

  - by LG

  Hi, I'm implementing a driver that extends IOSCSIPeripheralDeviceType00 as I need to send custom SCSI commands to a device. I'm following the VendorSpecificType00 and SimpleUserClient examples and http://wagerlabs.com/writing-a-mac-osx-usb-device-driver-that-impl as an example. I built my kernel extension and it loads fine with kextload and it shows up in kextstat. The problem is that I can't locate it in my user space code. Here's the important (I think) part of: my driver code: #define super IOSCSIPeripheralDeviceType00 OSDefineMetaClassAndStructors(com_mycompany_driver_Foo, IOSCSIPeripheralDeviceType00) my user client code: #define super IOUserClient OSDefineMetaClassAndStructors(com_mycompany_driver_FooUserClient, IOUserClient) the plist: CFBundleIdentifier -> com.mycompany.driver.Foo IOCLass -> com_mycompany_driver_Foo IOUserClientClass -> com_mycompany_driver_FooUserClient IOProviderClass -> IOSCSIPeripheralDeviceNub Here's how I try to locate the driver in my user space code (similar to SimpleUserClient): dictRef = IOServiceMatching("com_mycompany_driver_Foo"); kernResult = IOServiceGetMatchingServices(kIOMasterPortDefault, dictRef, &iterator); When I execute the code, iterator is 0. I noticed that in the VendorSpecificType00 code, the localization of the driver is done differently: dictRef = IOServiceMatching("IOBlockStorageServices"); kr = IOServiceGetMatchingServices(kIOMasterPortDefault, dictRef, &iter); while ((service = IOIteratorNext(iter))) { io_registry_entry_t parent; kr = IORegistryEntryGetParentEntry(service, kIOServicePlane, &parent); ... // We're only interested in the parent object if it's our driver class. if (IOObjectConformsTo(parent, "com_apple_dts_driver_VendorSpecificType00")) { I tried doing that but it didn't work either. Thanks for reading and your help, -L

  Read the article

• The enterprise vendor con - connecting SSD's using SATA 2 (3Gbits) thus limiting there performance

  - by tonyrogerson

  When comparing SSD against Hard drive performance it really makes me cross when folk think comparing an array of SSD running on 3GBits/sec to hard drives running on 6GBits/second is somehow valid. In a paper from DELL (http://www.dell.com/downloads/global/products/pvaul/en/PowerEdge-PowerVaultH800-CacheCade-final.pdf) on increasing database performance using the DELL PERC H800 with Solid State Drives they compare four SSD drives connected at 3Gbits/sec against ten 10Krpm drives connected at 6Gbits [Tony slaps forehead while shouting DOH!]. It is true in the case of hard drives it probably doesn’t make much difference 3Gbit or 6Gbit because SAS and SATA are both end to end protocols rather than shared bus architecture like SCSI, so the hard drive doesn’t share bandwidth and probably can’t get near the 600MiBytes/second throughput that 6Gbit gives unless you are doing contiguous reads, in my own tests on a single 15Krpm SAS disk using IOMeter (8 worker threads, queue depth of 16 with a stripe size of 64KiB, an 8KiB transfer size on a drive formatted with an allocation size of 8KiB for a 100% sequential read test) I only get 347MiBytes per second sustained throughput at an average latency of 2.87ms per IO equating to 44.5K IOps, ok, if that was 3GBits it would be less – around 280MiBytes per second, oh, but wait a minute [...fingers tap desk] You’ll struggle to find in the commodity space an SSD that doesn’t have the SATA 3 (6GBits) interface, SSD’s are fast not only low latency and high IOps but they also offer a very large sustained transfer rate, consider the OCZ Agility 3 it so happens that in my masters dissertation I did the same test but on a difference box, I got 374MiBytes per second at an average latency of 2.67ms per IO equating to 47.9K IOps – cost of an 240GB Agility 3 is £174.24 (http://www.scan.co.uk/products/240gb-ocz-agility-3-ssd-25-sata-6gb-s-sandforce-2281-read-525mb-s-write-500mb-s-85k-iops), but that same drive set in a box connected with SATA 2 (3Gbits) would only yield around 280MiBytes per second thus losing almost 100MiBytes per second throughput and a ton of IOps too. So why the hell are “enterprise” vendors still only connecting SSD’s at 3GBits? Well, my conspiracy states that they have no interest in you moving to SSD because they’ll lose so much money, the argument that they use SATA 2 doesn’t wash, SATA 3 has been out for some time now and all the commodity stuff you buy uses it now. Consider the cost, not in terms of price per GB but price per IOps, SSD absolutely thrash Hard Drives on that, it was true that the opposite was also true that Hard Drives thrashed SSD’s on price per GB, but is that true now, I’m not so sure – a 300GByte 2.5” 15Krpm SAS drive costs £329.76 ex VAT (http://www.scan.co.uk/products/300gb-seagate-st9300653ss-savvio-15k3-25-hdd-sas-6gb-s-15000rpm-64mb-cache-27ms) which equates to £1.09 per GB compared to a 480GB OCZ Agility 3 costing £422.10 ex VAT (http://www.scan.co.uk/products/480gb-ocz-agility-3-ssd-25-sata-6gb-s-sandforce-2281-read-525mb-s-write-410mb-s-30k-iops) which equates to £0.88 per GB. Ok, I compared an “enterprise” hard drive with a “commodity” SSD, ok, so things get a little more complicated here, most “enterprise” SSD’s are SLC and most commodity are MLC, SLC gives more performance and wear, I’ll talk about that another day. For now though, don’t get sucked in by vendor marketing, SATA 2 (3Gbit) just doesn’t cut it, SSD need 6Gbit to breath and even that SSD’s are pushing. Alas, SSD’s are connected using SATA so all the controllers I’ve seen thus far from HP and DELL only do SATA 2 – deliberate? Well, I’ll let you decide on that one.

  Read the article

• Cannot Mount USB 3.0 Hard Disk ?!!

  - by Tenken

  Hi, I have a USB 3.0 external hard disk which I am unable to mount. The entry appears in the "lsusb" command, but I do not exactly understand how to mount it. This is the output for my lsusb command. "ASMedia Technology Inc." is the USB 3.0 device. I would appreciate some help in mounting and accessing the hard disk. This the relevant output of my "lsusb -v" : Bus 009 Device 002: ID 174c:5106 ASMedia Technology Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x174c ASMedia Technology Inc. idProduct 0x5106 bcdDevice 0.01 iManufacturer 2 ASMedia iProduct 3 AS2105 iSerial 1 00000000000000000000 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.35-28-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:04:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0503 highspeed power enable connect Port 4: 0000.0503 highspeed power enable connect Device Status: 0x0003 Self Powered Remote Wakeup Enabled This is the error given when I try to mount the hard drive: shinso@shinso-IdeaPad:~$ sudo mount /dev/sdb /mnt [sudo] password for shinso: mount: /dev/sdb: unknown device This the output of "dmesg|tail": [30062.774178] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [30535.800977] usb 9-4: USB disconnect, address 3 [30659.237342] Valid eCryptfs headers not found in file header region or xattr region [30659.237351] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [31259.268310] Valid eCryptfs headers not found in file header region or xattr region [31259.268313] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [31860.059058] Valid eCryptfs headers not found in file header region or xattr region [31860.059062] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [32465.220590] Valid eCryptfs headers not found in file header region or xattr region [32465.220593] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO I am using Ubuntu 10.10 (64 bit). Any help is appreciated.

  Read the article

• HP DAT72x6 autoloader

  - by ericmayo

  Hoping someone here has seen this similar issue and can offer soem advise... I have an HP DAT72x6 auto loader tape backup unit. The external kind, here is a link to an owner's manual I found of it. http://www.dectrader.com/docs/set2/emr_na-c00070400-1.pdf I purchased the unit used about 6 months ago. The unit stopped working after 3-4 back-ups, it's used one day a month to do a monthly backup of another system. Suffice it to say the unit gets very little usage. There is an amber light on the front of the unit called the OAR (Operator Attention Required). The manual states to call for service when this light comes on and stays on. I've tried a few things to resolve but none are working. I've tried power cycling, re-securing the SCSI cables at both ends. Unit was used so I didn't pay much ($500) and so I don't want to spend a lot to have it fixed; might as well buy something new one if fixing this is going to cost more than $100-$150 bucks. I'm curious to see if anyone here has been around these devices or possibly is an HP repair person that can give me some things to try to resolve. The manual states that a solid amber OAR light indicates a hardware failure. When I power cycle the unit I see one of two scenarios so far. The unit powers up, shows self test in the LCD, then LCD changes to show all possible images and the OAR light comes on. The unit powers up, LCD is completely blank, the green lights go through some sort of process of going on and off and later the amber OAR light comes on and stays on. If it's a simple misalignment issue, I may be able to fix myself but not knowing what could cause the OAR light to come on gives me no where to even start. Google around gave no help either. I hoping someone here has experience with this and can help or point me in the right direction. Also, I don't have the HP Diagnostic tools mentioned in many manuals. The unit is connected to a Linux box. The 3-4 backups I've done with it so far have had no issues. We run amanda backup. Before this incident the unit was backing up and reading tapes fine. Thanks for any help or suggestions.

  Read the article

• DPM 2010 "Disk failed or disk not found"

  - by SysAdmin

  I have an HP Proliant ML110 G5 server with Windows server 2008R2 only dedicated for DPM 2010. This server has a limit in HD of 8TB which has already been met. I'm now stuck in this situation where my disk keeps failing "Disk failed or Disk not found" in the disk management. Only after I reboot the system the disk comes back up. Today I was running my monthly tape backup on a certain protection group and the disk failed again while the tape job was running (so the job wasn't completed). This is the description of the error in the alerts: "The disk Disk 1 - Hitachi HDS722020ALA330 SCSI Disk Device cannot be detected or has stopped responding. All subsequent protection activities that use this disk will fail until the disk is brought back online. (ID 3120)". My backup system is becoming useless! I don't think that is a hardware issue (please correct me if I'm wrong) since the HD works fine for a certain period of time which is becoming shorter and shorter. I basically have no more option to fix this problem. I tried to fix any error that was coming up in the event viewer with no luck (included one regarding the SQL2008 compatibility issue). The disk keeps failing! Now I'm only trying to recover/migrate the data from the disk that is having problem but my issue now is that I cannot add any drives to my server since I already got installed the maximum storage capacity 8TB. I thought about 2 simple options. Please tell me what you guys think about it; Unplug one of the 2 storage pool disks (disk0, that one without problem) from the machine and install a new one in order to migrate the data with the Migration tool for DPM. Remove the defective disk (disk1), put back the disk0 and run the synchronization/consistency check on all the groups to recreate replicas and recovery points. Run diskpart.exe and clean up the disk (loosing all data) and hoping that he will work after I sync all the protection groups. Both solutions are not elegant but I have no better options at the moment. Please I need some help. Thanks for your time Angelo

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Looking for a new backup solution to replace dying tape drive

  - by E3 Group

  We're running Windows Server 2003 SBS and another machine with Server 2003 Standard on it. The SBS server is about 7 years old running pretty much 24/7 - a HP server of some description. We have an Ultrium 448 cycling LTO2 400GB tapes daily and incrementally backing up approximately 100gb worth of data (20gb C:\ and system state, 40gb exchange, 40gb database for some crap marketing software) on BackupExec 10D. As of 5 months ago, the backups have been consistently failing with IO errors, bad reads and some write errors. When I say consistent, I mean every time and we haven't had a proper backup for the entire 5 months - So if the server explodes tomorrow, 7 years worth of data will just cease to exist. I've only just recently rejoined the company and am looking at rectifying the more concerning problems, so the first thing I did was try a backup to an USB2.0 external drive. It was excruciatingly slow. In fact it was so slow it took 40 hours and it still wasn't finished. I ended up cancelling it and reconfiguring the selections again to reduce file size. This, however, isn't a permanent solution. I concluded that the IO error was either from a faulty tape drive (which has a tape stuck in there right now and not coming out) or from a dying SCSI controller. Neither of them are good news and both are extremely expensive to fix. I'm operating on an extremely low budget so have been looking at outsourcing the backups. A company in Sydney (where I'm located) offer incremental online backups via a NAS. It costs almost double a new tape drive but offers monthly repayments which will let us get through times when cash flow is minimal. It seems like a sweet deal but it is still a little bit pricey. So I'm looking for a cheaper, yet reliable solution. Maybe some in-house NAS or something offsite? The idea is to avoid using tapes. Are there any recommendations for rectifying my current situation? Or are tapes the only way to go? I'm concerned that the server will die one day in the near future and I must be able to restore it to another server with different hardware.

  Read the article

• Disk IO causing high load on Xen/CentOS guest

  - by Peter Lindqvist

  I'm having serious issues with a xen based server, this is on the guest partition. It's a paravirtualized CentOS 5.5. The following numbers are taken from top while copying a large file over the network. If i copy the file another time the speed decreases in relation to load average. So the second time it's half the speed of the first time. It needs some time to cool off after this. Load average slowly decreases until it's once again usable. ls / takes about 30 seconds. top - 13:26:44 up 13 days, 21:44, 2 users, load average: 7.03, 5.08, 3.15 Tasks: 134 total, 2 running, 132 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.1%sy, 0.0%ni, 25.3%id, 74.5%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 1048752k total, 1041460k used, 7292k free, 3116k buffers Swap: 2129912k total, 40k used, 2129872k free, 904740k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1506 root 10 -5 0 0 0 S 0.3 0.0 0:03.94 cifsd 1 root 15 0 2172 644 556 S 0.0 0.1 0:00.08 init Meanwhile the host is ~0.5 load avg and steady over time. ~50% wait Server hardware is dual xeon, 3gb ram, 170gb scsi 320 10k rpm, and shouldn't have any problems with copying files over the network. disk = [ "tap:aio:/vm/dev01.img,xvda,w" ] I also get these in the log INFO: task syslogd:1350 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syslogd D 00062E4F 2208 1350 1 1353 1312 (NOTLB) c0ef0ed0 00000286 6e71a411 00062e4f c0ef0f18 00000009 c0f20000 6e738bfd 00062e4f 0001e7ec c0f2010c c181a724 c1abd200 00000000 ffffffff c0ef0ecc c041a180 00000000 c0ef0ed8 c03d6a50 00000000 00000000 c03d6a00 00000000 Call Trace: [<c041a180>] __wake_up+0x2a/0x3d [<ee06a1ea>] log_wait_commit+0x80/0xc7 [jbd] [<c043128b>] autoremove_wake_function+0x0/0x2d [<ee065661>] journal_stop+0x195/0x1ba [jbd] [<c0490a32>] __writeback_single_inode+0x1a3/0x2af [<c04568ea>] do_writepages+0x2b/0x32 [<c045239b>] __filemap_fdatawrite_range+0x66/0x72 [<c04910ce>] sync_inode+0x19/0x24 [<ee09b007>] ext3_sync_file+0xaf/0xc4 [ext3] [<c047426f>] do_fsync+0x41/0x83 [<c04742ce>] __do_fsync+0x1d/0x2b [<c0405413>] syscall_call+0x7/0xb ======================= I have tried disabling irqbalanced as suggested here but it does not seem to make any difference.

  Read the article

• Partition table corrupted (USB flash drive)

  - by 13ren

  It's an 8 GB Patriot thumb drive, which I've used extensively with lots of data. Today, it is detected, but all data is gone: (EDIT at least some data is still there, but the partition table is gone) EDIT @Sathya (thanks) here's the relevant output from sudo fdisk -l: Disk /dev/sdc: 8019 MB, 8019509248 bytes 247 heads, 62 sectors/track, 1022 cylinders Units = cylinders of 15314 * 512 = 7840768 bytes Disk /dev/sdc doesn't contain a valid partition table It looks like it is /dev/sdc, with that 8 GB... and no partition table. I tried to mount /dev/sdc (and then dmesg | tail): /media> sudo mount /dev/sdc mytmp mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so /media> dmesg | tail [ 24.300000] sdc: unknown partition table [ 24.320000] sd 2:0:0:0: Attached scsi removable disk sdc [ 24.370000] usb-storage: device scan complete [ 26.870000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 26.870000] EXT2-fs: group descriptors corrupted! [ 50.420000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 5565.470000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 5565.470000] EXT2-fs: group descriptors corrupted! EDIT @Col: results from testdisk Disk /dev/sdc - 8013 MB / 7642 MiB - CHS 1022 247 62 Current partition structure: Partition Start End Size in sectors Partition sector doesn't have the endmark 0xAA55 After I hit [proceed], it says: Structure: Ok. Keys A: add partition, L: load backup, Enter: to continue The "Structure: Ok." seems reassuring... will "A: add partition" make my old data accessible (if it's still there), or will it make a new, fresh partition? Another option is "[ MBR Code ] Write TestDisk MBR code to first sector" - would it be better to do this? EDIT I found that at least some of my data is still on the flash drive, by using the below, and searching for English text in less (like " the "): cat /dev/sde | tr -cd '\11\12\40\1540-\176' | less (The drive changed from "/dev/sdb" to "/dev/sde" because I connected some extra drives today). I've learnt that "/dev/sde1" would be the first partition; and "/dev/sde" is the whole drive. Because unix treats these devices just like files, you can use all the ordinary unix file commands on them, like cat, and then process them like any other stream of data. The tr above removes non-printable characters ("\40" is space, which I wanted to preserve). In less, you can use "/" to search, similar to Vim. How can I get my data back (assuming it's still there)? If only the partition table is corrupted, is there a standard "partition recovery tool"? Is there a way to "repartition" without deleting everything?

  Read the article

• server 2008 r2 - wbadmin systemstatebackup - system writer not found in the backup

  - by TWood

  I am trying to manually run a systemstatebackup command on my server 2008 r2 box and I am getting an error code '2155347997' when I view the backup event log details. The command line tells me that I have log files written to the c:\windows\logs\windowsserverbackup\ path but I have no files of the .log type there. My command window tells me "System Writer is not found in the backup". However when I run vssadmin list writers I find System Writer in the list and it shows normal status with no last errors stored. I am running this from an elevated command prompt as well as from a logged on administrator account. My backup target path has permission for network service to have full control and it has plenty of free space. Looking in eventlog I have two VSS error 8194 that happen immediately before the Backup error 517 which has the errorcode 2155347997 listed. All three of these errors are a result of trying to run the command for the systemstatebackup. It's my belief that some VSS related permission is failing and exiting the backup process before it ever gets started. Because of this the initial code that creates the log files must not be running and this is why I have no files. When running the systemstatebackup command from the command prompt and watching the windowsserverbackup directory I do see that I have a Wbadmin.0.etl file which gets created but it is deleted when the backup errors out and stops. I have looked online and there are numerous opinions as to the cause of this error. These are the things I have corrected to try and fix this issue before posting here: Machine runs a HP 1410i smart array controller but at one time also used a LSI scsi card. Used networkadminkb.com's kb# a467 to find one LSI_SCSI entry in HKLMSysCurrentControlSetServices which start was set to 0x0 and I modified to 0x3. No changes. In HKLMSystemCurrentControlSetServicesVSSDiag I gave network service full control where it previously only had "Special Permission". No changes. I followed KB2009272 to manually try to fix system writer. These are all of the things I have tried. What else should I look at to resolve this issue? It may be important to note that I run Mozy Pro on this server and that was known in the past to use VSS for copying operations and it occasionally threw an error. However since an update last year those error event log entries have stopped.

  Read the article

• How to get an inactive RAID device working again?

  - by Jonik

  After booting, my RAID1 device (/dev/md_d0 *) sometimes goes in some funny state and I cannot mount it. * Originally I created /dev/md0 but it has somehow changed itself into /dev/md_d0. # mount /opt mount: wrong fs type, bad option, bad superblock on /dev/md_d0, missing codepage or helper program, or other error (could this be the IDE device where you in fact use ide-scsi so that sr0 or sda or so is needed?) In some cases useful info is found in syslog - try dmesg | tail or so The RAID device appears to be inactive somehow: # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d0 : inactive sda4[0](S) 241095104 blocks # mdadm --detail /dev/md_d0 mdadm: md device /dev/md_d0 does not appear to be active. Question is, how to make the device active again (using mdmadm, I presume)? (Other times it's alright (active) after boot, and I can mount it manually without problems. But it still won't mount automatically even though I have it in /etc/fstab: /dev/md_d0 /opt ext4 defaults 0 0 So a bonus question: what should I do to make the RAID device automatically mount at /opt at boot time?) This is an Ubuntu 9.10 workstation. Background info about my RAID setup in this question. Edit: My /etc/mdadm/mdadm.conf looks like this. I've never touched this file, at least by hand. # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR <my mail address> # definitions of existing MD arrays # This file was auto-generated on Wed, 27 Jan 2010 17:14:36 +0200 In /proc/partitions the last entry is md_d0 at least now, after reboot, when the device happens to be active again. (I'm not sure if it would be the same when it's inactive.) Resolution: as Jimmy Hedman suggested, I took the output of mdadm --examine --scan: ARRAY /dev/md0 level=raid1 num-devices=2 UUID=de8fbd92[...] and added it in /etc/mdadm/mdadm.conf, which seems to have fixed the main problem. After changing /etc/fstab to use /dev/md0 again (instead of /dev/md_d0), the RAID device also gets automatically mounted!

  Read the article

• Ubuntu stopped recognizing my iPod

  - by flashnode

  Rythmbox on Ubuntu 10.10 used to recognize my 3rd gen Nano and transfer mp3s. Now I plug it in and Ubuntu doesn't pop-up that box that asks what you want to do anymore. It is only recognized if I reboot and the thing is plugged in. Here is the output to 'lsusb -v -s bus:device' Bus 001 Device 008: ID 05ac:1262 Apple, Inc. iPod Nano 3.Gen Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x05ac Apple, Inc. idProduct 0x1262 iPod Nano 3.Gen bcdDevice 0.01 iManufacturer 1 Apple Inc. iProduct 2 iPod iSerial 3 000A27001A670128 bNumConfigurations 2 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 149 bNumInterfaces 3 bConfigurationValue 2 iConfiguration 4 iPod USB Interface bmAttributes 0xc0 Self Powered MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 1 Audio bInterfaceSubClass 1 Control Device bInterfaceProtocol 0 iInterface 0 AudioControl Interface Descriptor: bLength 9 bDescriptorType 36 bDescriptorSubtype 1 (HEADER) bcdADC 1.00 wTotalLength 30 bInCollection 1 baInterfaceNr( 0) 1 AudioControl Interface Descriptor: bLength 12 bDescriptorType 36 bDescriptorSubtype 2 (INPUT_TERMINAL) bTerminalID 1 wTerminalType 0x0201 Microphone bAssocTerminal 2 bNrChannels 2 wChannelConfig 0x0003 Left Front (L) Right Front (R) iChannelNames 0 iTerminal 0 AudioControl Interface Descriptor: bLength 9 bDescriptorType 36 bDescriptorSubtype 3 (OUTPUT_TERMINAL) bTerminalID 2 wTerminalType 0x0101 USB Streaming bAssocTerminal 1 bSourceID 1 iTerminal 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 1 Audio bInterfaceSubClass 2 Streaming bInterfaceProtocol 0 iInterface 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 1 bNumEndpoints 1 bInterfaceClass 1 Audio bInterfaceSubClass 2 Streaming bInterfaceProtocol 0 iInterface 0 AudioStreaming Interface Descriptor: bLength 7 bDescriptorType 36 bDescriptorSubtype 1 (AS_GENERAL) bTerminalLink 2 bDelay 1 frames wFormatTag 1 PCM AudioStreaming Interface Descriptor: bLength 35 bDescriptorType 36 bDescriptorSubtype 2 (FORMAT_TYPE) bFormatType 1 (FORMAT_TYPE_I) bNrChannels 2 bSubframeSize 2 bBitResolution 16 bSamFreqType 9 Discrete tSamFreq[ 0] 8000 tSamFreq[ 1] 11025 tSamFreq[ 2] 12000 tSamFreq[ 3] 16000 tSamFreq[ 4] 22050 tSamFreq[ 5] 24000 tSamFreq[ 6] 32000 tSamFreq[ 7] 44100 tSamFreq[ 8] 48000 Endpoint Descriptor: bLength 9 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 1 Transfer Type Isochronous Synch Type None Usage Type Data wMaxPacketSize 0x00c0 1x 192 bytes bInterval 4 bRefresh 0 bSynchAddress 0 AudioControl Endpoint Descriptor: bLength 7 bDescriptorType 37 bDescriptorSubtype 1 (EP_GENERAL) bmAttributes 0x01 Sampling Frequency bLockDelayUnits 0 Undefined wLockDelay 0 Undefined Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 0 No Subclass bInterfaceProtocol 0 None iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.01 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 208 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 2 Device Status: 0x0000 (Bus Powered) This ubuntu forum told me to check the automount settings under /apps/nautilus/preferences/media_automount_open in gconf-editor. And I did that. Any clues?

  Read the article

• DVD not detected?

  - by Benjamin

  As i insert a DVD in my drive (on a laptop) using Kubuntu 12.04, the DVD is not detected. The drive takes the DVD, I can hear it munching on it for a while, and then nothing. Even ejecting the DVD becomes a hassle, I need to do that at boot time otherwise the OS won't allow me to eject. Kubuntu 12.04 used to read and mount the same DVDs just fine a week ago. Edit: since I am able to boot from CD, can I safely assume the issue is not a hardware issue? How can I fix this? wodim --devices returns: wodim: Overview of accessible drives (1 found) : ------------------------------------------------------------------------- 0 dev='/dev/sg1' rwrw-- : 'Optiarc' 'DVD+-RW AD-7640A' ------------------------------------------------------------------------- sudo lshw -class disk returns: *-cdrom description: DVD-RAM writer product: DVD+-RW AD-7640A vendor: Optiarc physical id: 0.0.0 bus info: scsi@3:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/dvdrw2 logical name: /dev/sr0 version: JD06 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=open lspci returns: 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 0c) 00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3) 00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 03) 00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03) 06:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:05.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 08:05.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 02) 08:05.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) and lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0c45:63e0 Microdia Sonix Integrated Webcam Bus 003 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader The /etc/modprobe.d/blacklist.conf contains: # This file lists those modules which we don't want to be loaded by # alias expansion, usually so some other driver will be loaded for the # device instead. # evbug is a debug tool that should be loaded explicitly blacklist evbug # these drivers are very simple, the HID drivers are usually preferred blacklist usbmouse blacklist usbkbd # replaced by e100 blacklist eepro100 # replaced by tulip blacklist de4x5 # causes no end of confusion by creating unexpected network interfaces blacklist eth1394 # snd_intel8x0m can interfere with snd_intel8x0, doesn't seem to support much # hardware on its own (Ubuntu bug #2011, #6810) blacklist snd_intel8x0m # Conflicts with dvb driver (which is better for handling this device) blacklist snd_aw2 # causes failure to suspend on HP compaq nc6000 (Ubuntu: #10306) blacklist i2c_i801 # replaced by p54pci blacklist prism54 # replaced by b43 and ssb. blacklist bcm43xx # most apps now use garmin usb driver directly (Ubuntu: #114565) blacklist garmin_gps # replaced by asus-laptop (Ubuntu: #184721) blacklist asus_acpi # low-quality, just noise when being used for sound playback, causes # hangs at desktop session start (Ubuntu: #246969) blacklist snd_pcsp # ugly and loud noise, getting on everyone's nerves; this should be done by a # nice pulseaudio bing (Ubuntu: #77010) blacklist pcspkr # EDAC driver for amd76x clashes with the agp driver preventing the aperture # from being initialised (Ubuntu: #297750). Blacklist so that the driver # continues to build and is installable for the few cases where its # really needed. blacklist amd76x_edac

  Read the article

• ImgBurn fails to burn data CD-R disk due to "Layouts do not match" error

  - by 0xAether

  I have a reoccurring problem with the program ImgBurn. Whenever I try and burn anything to a CD-R using ImgBurn it burns just fine, except for when I go and verify the disk. It tells me that the "Layouts do not match". Windows 7 shows the disk as completely blank. Although, I see on the bottom of the disk it has been written to. I can burn ISO files to DVD-R's just fine. This only seems to happen with CD-R's. The CD-R's I'm using are Memorex Cool Colors 52x CD-R's. I have looked on Google, and it seems like I'm not the only one this happens to. Unfortunately, no one is able to provide an explanation. I have included the log file from the last CD I just burnt. If you need anything else to better diagnose this problem, I will gladly provide it. ; //****************************************\\ ; ImgBurn Version 2.5.7.0 - Log ; Monday, 19 November 2012, 16:11:57 ; \\****************************************// ; ; I 16:04:55 ImgBurn Version 2.5.7.0 started! I 16:04:55 Microsoft Windows 7 Ultimate x64 Edition (6.1, Build 7601 : Service Pack 1) I 16:04:55 Total Physical Memory: 4,156,380 KB - Available: 3,317,144 KB I 16:04:55 Initialising SPTI... I 16:04:55 Searching for SCSI / ATAPI devices... I 16:04:56 -> Drive 1 - Info: Optiarc DVD RW AD-7560S SH03 (D:) (SATA) I 16:04:56 Found 1 DVD±RW/RAM! I 16:05:37 Operation Started! I 16:05:37 Source File: C:\Users\Aaron\Desktop\VMware Workstation 9.iso I 16:05:37 Source File Sectors: 223,057 (MODE1/2048) I 16:05:37 Source File Size: 456,820,736 bytes I 16:05:37 Source File Volume Identifier: VMwareWorksta9 I 16:05:37 Source File Volume Set Identifier: 20121119_2102 I 16:05:37 Source File File System(s): ISO9660, Joliet I 16:05:37 Destination Device: [1:0:0] Optiarc DVD RW AD-7560S SH03 (D:) (SATA) I 16:05:37 Destination Media Type: CD-R (Disc ID: 97m17s06f, Moser Baer India) I 16:05:37 Destination Media Supported Write Speeds: 10x, 16x, 20x, 24x I 16:05:37 Destination Media Sectors: 359,847 I 16:05:37 Write Mode: CD I 16:05:37 Write Type: SAO I 16:05:37 Write Speed: 6x I 16:05:37 Lock Volume: Yes I 16:05:37 Test Mode: No I 16:05:37 OPC: No I 16:05:37 BURN-Proof: Enabled W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - Wanted: 1,058 KB/s (6x), Got: 1,764 KB/s (10x) / 11,080 KB/s (63x) W 16:05:37 The drive only supports writing these discs at 10x, 16x, 20x, 24x. I 16:05:38 Filling Buffer... (80 MB) I 16:05:40 Writing LeadIn... I 16:06:07 Writing Session 1 of 1... (1 Track, LBA: 0 - 223056) I 16:06:07 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 223056) I 16:11:00 Synchronising Cache... I 16:11:18 Exporting Graph Data... I 16:11:18 Graph Data File: C:\Users\Aaron\AppData\Roaming\ImgBurn\Graph Data Files\Optiarc_DVD_RW_AD-7560S_SH03_MONDAY-NOVEMBER-19-2012_4-05_PM_97m17s06f_6x.ibg I 16:11:18 Export Successfully Completed! I 16:11:18 Operation Successfully Completed! - Duration: 00:05:41 I 16:11:18 Average Write Rate: 1,522 KB/s (10.1x) - Maximum Write Rate: 1,544 KB/s (10.3x) I 16:11:18 Cycling Tray before Verify... W 16:11:23 Waiting for device to become ready... I 16:11:47 Device Ready! E 16:11:47 CompareImageFileLayouts Failed! - Session Count Not Equal (1/0) E 16:11:47 Verify Failed! - Reason: Layouts do not match. I 16:11:57 Close Request Acknowledged I 16:11:57 Closing Down... I 16:11:57 Shutting down SPTI... I 16:11:57 ImgBurn closed!

  Read the article

• How do I determine if my controller is in IDE or AHCI mode in Linux?

  - by philcolbourn

  I have an old MacBook Pro 4,1 (early 2008) - but I suspect an answer would apply to many MacBook Pros. It has an Intel IDE/SATA controller (ICH8M/ICH8M-E). I have installed a patched MBR that is supposed to put my controller into AHCI mode. It does this by setting some controller port value that I don't understand. This seems to work as I get this from lspci: 00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) 00:1f.2 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03) Now most, perhaps all, sites that provide a solution (enabling AHCI) suggest that after a sleep/wake cycle that a controller will revert to IDE mode due to how Apple support Windows. They recommend disabling sleep. From author of patchedcode.bin I think Enabling AHCI for Windows on MacBooks NB: I do not have bootcamp installed and I do not have Windows installed. Is there a way to prove that my controller is in IDE or AHCI mode? Background Data Using patchedcode.bin MBR I get this in syslog: Jun 12 22:33:22 max kernel: [ 1.860955] ahci 0000:00:1f.2: version 3.0 Jun 12 22:33:22 max kernel: [ 1.861052] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X Jun 12 22:33:22 max kernel: [ 1.861117] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps 0x1 impl SATA mode Jun 12 22:33:22 max kernel: [ 1.861120] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems Jun 12 22:33:22 max kernel: [ 1.861130] ahci 0000:00:1f.2: setting latency timer to 64 Jun 12 22:33:22 max kernel: [ 1.880880] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) Jun 12 22:33:22 max kernel: [ 1.880983] scsi2 : ahci Jun 12 22:33:22 max kernel: [ 1.884552] scsi3 : ahci Jun 12 22:33:22 max kernel: [ 1.886932] scsi4 : ahci Jun 12 22:33:22 max kernel: [ 1.886998] ata3: SATA max UDMA/133 abar m2048@0xdb504000 port 0xdb504100 irq 45 Jun 12 22:33:22 max kernel: [ 1.887000] ata4: DUMMY Jun 12 22:33:22 max kernel: [ 1.887002] ata5: DUMMY Jun 12 22:33:22 max kernel: [ 2.204103] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jun 12 22:33:22 max kernel: [ 2.204656] ata3.00: ATA-8: FUJITSU MHY2200BH, 0081000D, max UDMA/100 Jun 12 22:33:22 max kernel: [ 2.204662] ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32), AA Jun 12 22:33:22 max kernel: [ 2.205324] ata3.00: configured for UDMA/100 Jun 12 22:33:22 max kernel: [ 2.205554] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHY2200B 0081 PQ: 0 ANSI: 5 Using my original MBR I get this from syslog: Jun 13 18:07:13 max kernel: [ 0.622861] ata_piix 0000:00:1f.1: version 2.13 Jun 13 18:07:13 max kernel: [ 0.622869] ata_piix 0000:00:1f.1: power state changed by ACPI to D0 Jun 13 18:07:13 max kernel: [ 0.622924] ata_piix 0000:00:1f.1: setting latency timer to 64 Jun 13 18:07:13 max kernel: [ 0.623339] scsi0 : ata_piix Jun 13 18:07:13 max kernel: [ 0.623730] scsi1 : ata_piix Jun 13 18:07:13 max kernel: [ 0.623765] ata1: PATA max UDMA/100 cmd 0x8108 ctl 0x811c bmdma 0x80e0 irq 21 Jun 13 18:07:13 max kernel: [ 0.623767] ata2: PATA max UDMA/100 cmd 0x8100 ctl 0x8118 bmdma 0x80e8 irq 21 Jun 13 18:07:13 max kernel: [ 0.623810] ata_piix 0000:00:1f.2: MAP [ Jun 13 18:07:13 max kernel: [ 0.623811] P0 -- -- -- ] Jun 13 18:07:13 max kernel: [ 0.623866] ata_piix 0000:00:1f.2: setting latency timer to 64 Jun 13 18:07:13 max kernel: [ 0.624241] scsi2 : ata_piix Jun 13 18:07:13 max kernel: [ 0.624558] scsi3 : ata_piix Jun 13 18:07:13 max kernel: [ 0.624862] ata3: SATA max UDMA/133 cmd 0x80f8 ctl 0x8114 bmdma 0x8020 irq 18 Jun 13 18:07:13 max kernel: [ 0.624865] ata4: SATA max UDMA/133 cmd 0x80f0 ctl 0x8110 bmdma 0x8028 irq 18 Jun 13 18:07:13 max kernel: [ 1.208879] ata3.00: ATA-8: FUJITSU MHY2200BH, 0081000D, max UDMA/100 Jun 13 18:07:13 max kernel: [ 1.208882] ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 0/32) Jun 13 18:07:13 max kernel: [ 1.208961] ata1.01: ATAPI: MATSHITA DVD+/-RW UJ-867S, 1.00, max UDMA/33 Jun 13 18:07:13 max kernel: [ 1.216186] ata3.00: configured for UDMA/100 Jun 13 18:07:13 max kernel: [ 1.224396] ata1.01: configured for UDMA/33

  Read the article

• SATA drive problems with two SIL RAID cards

  - by Jon Topper

  I've just put a second SiI 3114 SATARaid card in my home server so that I could add another pair of SATA drives and increase my storage space. Annoyingly, it doesn't seem to work: [ 32.816030] ata5: lost interrupt (Status 0x0) [ 32.816072] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 32.816091] ata5.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in [ 32.816094] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 32.816101] ata5.00: status: { DRDY } [ 32.816117] ata5: hard resetting link [ 33.136082] ata5: SATA link down (SStatus 0 SControl 0) [ 36.060940] irq 18: nobody cared (try booting with the "irqpoll" option) [ 36.060949] Pid: 0, comm: swapper Not tainted 2.6.31-20-generic #58-Ubuntu [ 36.060954] Call Trace: [ 36.060977] [] ? printk+0x18/0x1c [ 36.060997] [] __report_bad_irq+0x27/0x90 [ 36.061005] [] note_interrupt+0x150/0x190 [ 36.061011] [] handle_fasteoi_irq+0xac/0xd0 [ 36.061023] [] handle_irq+0x18/0x30 [ 36.061029] [] do_IRQ+0x47/0xc0 [ 36.061042] [] ? irq_exit+0x50/0x70 [ 36.061058] [] ? smp_apic_timer_interrupt+0x57/0x90 [ 36.061065] [] common_interrupt+0x30/0x40 [ 36.061075] [] ? native_safe_halt+0x5/0x10 [ 36.061082] [] default_idle+0x46/0xd0 [ 36.061088] [] cpu_idle+0x8c/0xd0 [ 36.061103] [] rest_init+0x55/0x60 [ 36.061111] [] start_kernel+0x2e6/0x2ec [ 36.061117] [] ? unknown_bootoption+0x0/0x19e [ 36.061133] [] i386_start_kernel+0x7c/0x83 [ 36.061137] handlers: [ 36.061139] [] (sil_interrupt+0x0/0xb0) [ 36.061151] Disabling IRQ #18 [ 38.136014] ata5: hard resetting link [ 38.456022] ata5: SATA link down (SStatus 0 SControl 0) [ 43.456013] ata5: hard resetting link [ 43.776022] ata5: SATA link down (SStatus 0 SControl 0) [ 43.776035] ata5.00: disabled [ 43.776055] ata5.00: device reported invalid CHS sector 0 [ 43.776074] sd 4:0:0:0: [sde] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 43.776082] sd 4:0:0:0: [sde] Sense Key : Aborted Command [current] [descriptor] [ 43.776092] Descriptor sense data with sense descriptors (in hex): [ 43.776097] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 43.776112] 00 00 00 00 [ 43.776118] sd 4:0:0:0: [sde] Add. Sense: No additional sense information [ 43.776127] end_request: I/O error, dev sde, sector 0 [ 43.776136] Buffer I/O error on device sde, logical block 0 [ 43.776170] ata5: EH complete [ 43.776187] ata5.00: detaching (SCSI 4:0:0:0) root@core:~# cat /proc/interrupts CPU0 0: 47 IO-APIC-edge timer 1: 8 IO-APIC-edge i8042 6: 3 IO-APIC-edge floppy 7: 0 IO-APIC-edge parport0 8: 0 IO-APIC-edge rtc0 9: 0 IO-APIC-fasteoi acpi 14: 53069 IO-APIC-edge pata_sis 15: 53004 IO-APIC-edge pata_sis 17: 112265 IO-APIC-fasteoi sata_sil 18: 200002 IO-APIC-fasteoi sata_sil, SiS SI7012 19: 111140 IO-APIC-fasteoi eth0 20: 0 IO-APIC-fasteoi ohci_hcd:usb2 21: 0 IO-APIC-fasteoi ohci_hcd:usb3 23: 0 IO-APIC-fasteoi ehci_hcd:usb1 NMI: 0 Non-maskable interrupts LOC: 6650492 Local timer interrupts SPU: 0 Spurious interrupts CNT: 0 Performance counter interrupts PND: 0 Performance pending work RES: 0 Rescheduling interrupts CAL: 0 Function call interrupts TLB: 0 TLB shootdowns TRM: 0 Thermal event interrupts THR: 0 Threshold APIC interrupts MCE: 0 Machine check exceptions MCP: 160 Machine check polls ERR: 0 MIS: 0 root@core:~# lspci | grep Raid 00:09.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 00:0a.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) root@core:~# lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 9.10 Release: 9.10 Codename: karmic root@core:~# uname -a Linux core.topper.me.uk 2.6.31-20-generic #58-Ubuntu SMP Fri Mar 12 05:23:09 UTC 2010 i686 GNU/Linux I've tried a combination of different kernel options (irqpoll, noapic, noacpi, pci=noapic) all to no avail. Does anyone have any bright ideas about how I can go about making this work? Swapping PCI cards around isn't an option as there are only two slots in this motherboard (an ASRock K7S41GX). The BIOS doesn't look to have too much in the way of configuration options regarding IRQ usage. Plan B is to ditch this server completely and buy a new QNAP for these drives to go in, but I was hoping to avoid doing this right now.

  Read the article

• Exchange Server 2007 Setup

  - by AlamedaDad

  Hi, I'm working on a upgrade to Exchange 2007 and I wanted to get some advise on hardware choices. We currently have an Exchange 2003 STD server with 400 users split between 6 AD Sites, that is housed on a single server. We need to move to a redundant, fault tolerant system to support our users. I'm planning on installing 2 Dell 1950 servers with W2k8-std to act as CAS and Hub servers, with NLB to allow abstraction of the actual server name to the users. There won't be an edge system since we have a Barracuda box already that will handle in/out spam/virus filtering. Backend I'm planning on 2 mailbox servers which will be Dell 2950s with 16GB RAM, 2 either dual-core or quad-core CPUs and 6 300GB SAS drives in some RAID config. These systems will be clustered using W2k8 Ent clustering and running CCR in Exchange. My questions are as follows: Is 16GB enough RAM for serving that many mailboxes along with the windows clustering and ccr? I'm trying to figure out disk layouts and I'm unsure of whether to use all local disk or some local and some SAN, via an OpenFiler iSCSI server. The SAN would be a Dell 2850 with 6 - 300GB SCSI drives and a PERC controller to slice as I want, with 8GB RAM. Option 1: 2 drives, RAID 1 - OS 2 drives, RAID 1 - Logs 2 drives, RAID 1 - Mail stores Option 2: 2 drives, RAID 1 - OS and logs 4 drives, RAID 5 - Mail Stores and scratch space for eseutil. Option 3: 2 drives, RAID 1 - OS 2 drives, RAID 1 - Logs 2 drives, RAID 0 - scratch space ~300GB iSCSI volume for mail stores Option 4: 2 drives, RAID 1 - OS 4 drives, RAID 5 - scratch space ~300GB iSCSI volume for mail stores ~300GB iSCSI volume for logs I have 2 sockets for CPUs and need to chose between dual and quad cores. The dual core have faster clocks but less cache and I'm thinking older architecture. Am I better off with more cores and cache while sacraficing clock speed? I am planning on adding the new E2K7 cluster to the E2K3 server and then move each mailbox over, all at once, then remove the old server. This seems more complicated than simply getting rid of the 2003 server and then adding the 2007 cluster and restoring the mailboxes using PowerControls or exmerge. The migration option lets me do this on my time, where a cutover means it all needs to work at once. If I go with the cutover method, how can I prebuild the servers and add them to the domain right after removing the 2003 server, or can't I? I think the answer is no and the migration is my only real option if I want to prebuild. I need to also migrate about 30GB of Public Folders. Is there anything special about this, other than specifying in the E2K7 install that I want older Outlook clients and PF's setup? I guess I could even keep the E2K3 server to host just the PFs? Lastly, if I have a mix of Outlook 200, 2003 and 2007 what do I need to do to make sure they all have access to the GAL and OAB? At time of cutover, we'll be at like 90% 2007, but we will have some older stuff around. My plan is to use Outlook Anywhere on laptops that are used outside the physical network. Are there any gotchas involved in that? I'm even thinking about using is for all Outlook clients, does anyone do that? The reason I'm considering it is that our WAN is really VPN tunnels over internet connections, so not a fully messhed, stable WAN. Thank you all very much for the assistance in advance and I look forward to discussion of these points! Regards...Michael

  Read the article

• dvd drive I/O error?

  - by bobby

  i get dis error evry time i burn a cd/dvd thru my dvd drive...!! Nero Burning ROM bobby 4C85-200E-4005-0004-0000-7660-0800-35X3-0000-407M-MX37-**** (*) Windows XP 6.1 IA32 WinAspi: - NT-SPTI used Nero Version: 7.11.3. Internal Version: 7, 11, 3, (Nero Express) Recorder: Version: UL01 - HA 1 TA 1 - 7.11.3.0 Adapter driver: HA 1 Drive buffer : 2048kB Bus Type : default CD-ROM: Version: 52PP - HA 1 TA 0 - 7.11.3.0 Adapter driver: HA 1 === Scsi-Device-Map === === CDRom-Device-Map === ATAPI-CD ROM-DRIVE-52MAX F: CdRom0 HL-DT-ST DVDRAM GSA-H12N G: CdRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 958MB (981560kB) Free physical memory: 309MB (317024kB) Memory in use : 67 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 11.6.2010 CD Image 10:43:02 AM #1 Text 0 File SCSIPTICommands.cpp, Line 450 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 10:43:02 AM #2 Text 0 File Burncd.cpp, Line 3186 HL-DT-ST DVDRAM GSA-H12N Buffer underrun protection activated 10:43:02 AM #3 Text 0 File Burncd.cpp, Line 3500 Turn on Disc-At-Once, using CD-R/RW media 10:43:02 AM #4 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 359848 ( 79:59.73) Last address to be written: 318783 ( 70:52.33) 10:43:02 AM #5 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 10:43:02 AM #6 Text 0 File DlgWaitCD.cpp, Line 2988 Recorder: HL-DT-ST DVDRAM G SA-H12N; CDR co de: 00 97 27 18; O SJ entry from: Pla smon Data systems Ltd. ATIP Data: Special Info [hex] 1: D0 00 A0, 2: 61 1B 12 (LI 97:27.18), 3: 4F 3B 4A ( LO 79:59.74) Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 0 0 00 (invalid) 10:43:02 AM #7 Text 0 File DlgWaitCD.cpp, Line 493 Protocol of DlgWaitCD activities: TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 318784 blo cks [G: HL-DT-ST DVDRAM GSA-H12N] -------------------------------------------------------------- 10:43:02 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 986 Prepare [G: HL-DT-ST DVDRAM GSA-H12N] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Se ssion Clo sed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next T rk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 6531768 32, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ -150 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 -150 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 318784 | 318784 | 0x00 318784 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 10:43:02 AM #10 Text 0 File SCSIPTICommands.cpp, Line 240 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 10:43:02 AM #11 Text 0 File Burncd.cpp, Line 4286 Caching options: cache CDRom or Network-Yes, small files-Yes ( ON 10:43:03 AM #19 Text 0 File MMC.cpp, Line 18034 CueData, Len=32 41 00 00 14 00 00 00 00 41 01 00 10 00 00 00 00 41 01 01 10 00 00 02 00 41 aa 01 14 00 46 34 22 10:43:03 AM #20 Text 0 File ThreadedTransfer.cpp, Line 268 Pipe memory size 83836800 10:43:16 AM #21 Text 0 File Cdrdrv.cpp, Line 1405 10:43:16.806 - G: HL-DT-ST DVDRAM GSA-H12N : Queue again later 10:43:42 AM #22 SPTI -1502 File SCSIPassThrough.cpp, Line 181 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1502) Sense Key: 0x04 (KEY_HARDWARE_ERROR) Nero Report 2 Nero Burning ROM Sense Code: 0x08 Sense Qual: 0x03 CDB Data: 0x2A 00 00 00 4D 00 00 00 20 00 00 00 Sense Area: 0x70 00 04 00 00 00 00 10 53 29 A1 80 08 03 Buffer x0c7d9a40: Len x10000 0xDC 87 EB 41 6E AC 61 5A 07 B2 DB 78 B5 D4 D9 24 0x8D BC 51 38 46 56 0F EE 16 15 5C 5B E3 B0 10 16 0x14 B1 C3 6E 30 2B C4 78 15 AB D5 92 09 B7 81 23 10:43:42 AM #23 CDR -1502 File Writer.cpp, Line 306 DMA-driver error, CRC error G: HL-DT-ST DVDRAM GSA-H12N 10:43:55 AM #24 Phase 38 File dlgbrnst.cpp, Line 1767 Burn process failed at 48x (7,200 KB/s) 10:43:55 AM #25 Text 0 File SCSIPTICommands.cpp, Line 287 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 10:44:01 AM #26 Text 0 File Cdrdrv.cpp, Line 11412 DriveLocker: UnLockVolume completed 10:44:01 AM #27 Text 0 File SCSIPTICommands.cpp, Line 450 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon Nero Report 3

  Read the article

< Previous Page | 12 13 14 15 16 17 18  | Next Page >