Search Results

Search found 5987 results on 240 pages for 'nested sets'.

Page 161/240 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

  • Supermicro X8SIL-F with Enermax Modu82+ 625W PSU booting issue

    - by Richard Whitman
    I am assembling a custom PC. The configuration is below: Motherboard: Supermicro X8SIL-F Processor: Intel Xeon 3430 Power Supply: Enermax Modu82+ 625W. Memory: Kingston KVR1333D3LQ8R9S/8GEC 8GBx1 installed in DimmA1 This power switch: Frozen CPU switch When I turn on the PSU, the motherboard tries to start itself before I even push the power switch. The following happens: The CPU fan rotates like once or twice, and then stops. After 1-2 seconds, the CPU fan tries to rotate again and stops after about one or two rotations. Finally, after another 1-2 seconds, it again starts and this time it rotates for about 3-4 seconds before stopping. If I pull out the Power switch, and turn on the PSU, again the MB turns on itself and the following happens: The CPU fan rotates like once or twice, and then stops. After 1-2 seconds, the CPU fan tries to rotate again and stops after about one or two rotations. Finally, after another 1-2 seconds, it again starts and the system boots properly I am sure there is nothing wrong with any of the components, because I have two sets of identical components (2 MBs, 2 CPUs, 2 PSUs, 2 switches and so on). And both of the systems show the same symptoms. Why is the MB booting up by itself? Why does it fail to boot when the Power Switch is installed? Is something wrong with the type of Power Switch I am using? PS: the power switch is installed correctly, I have double checked the MB manual to make sure its connecting the right pins.

    Read the article

  • Running HTTP and HTTPS connections for a single domain (say, www.example.com) through a Cisco ACE SS

    - by Paddu
    My web application config has a Cisco ACE load balancing across a server farm and I want to use the ACE as an SSL endpoint as well. To make this work, the network architect has come up with a design where all secure pages have to be served from secure.my-domain.com, while non-secure pages are served up from www.my-domain.com. The reason for this is apparently that the configuring the Cisco ACE to accept HTTPS requests on port 443 for a particular public IP prevents the simultaneous acceptance of HTTP requests on port 80 for the same IP. While I'm not a networking (or Cisco) expert, this seems to be intuitively wrong, as it would prevent any website using the Cisco ACE to serve pages on http://www.my-domain.com and https://www.my-domain.com simultaneously. In this situation, my questions are: Is this truly a limitation of the Cisco ACE when used as an SSL endpoint? If not, then can I assume that we can set up the ACE to accept connections for a particular IP on ports 80 and 443, and function as an SSL endpoint for the incoming requests on 443? Links to appropriate documentation most welcome here. Assuming the setup in the previous question, can I then redirect both sets of requests to the same server farm on the same port?

    Read the article

  • Serve a specific set of error pages for different subdirectories

    - by navitronic
    I am currently trying to setup 2 different sets of Error documents for separate folders within a website. I have 2 folders within the root of a site: demo/ live/ Any requests that return 404's or 403's within the demo folder needs to load one set of pages for the Apache errordocuments, eg. ErrorDocument 404 /statuses/demo-404.html ErrorDocument 403 /statuses/demo-403.html And the live needs to go to similarly name files. ErrorDocument 404 /statuses/live-404.html ErrorDocument 403 /statuses/live-403.html So far I have tried placing an .htaccess file in both directories with the ErrorDocument directives setup pointing to the specific files, the 404 works fine and references the correct page. However, the 403s do not work and revert to the server default when trying to access forbidden folders within the demo directory, the logs indicate the following: [Wed Jun 16 04:47:44 2010] [crit] [client 115.64.131.144] (13)Permission denied: /home/abstract/public_html/demo/xxx/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable Is this correct? Would apache revert to default because it is trying to look for the htaccess in a folder it doesn't have permission in? Why wouldn't it work it's way back through the folder tree? Can I make it do this?

    Read the article

  • Overriding HOMEDRIVE and HOMEPATH as a Windows 7 user

    - by MikeC
    My employer has an Active Directory group policy which sets my Windows 7 laptop HOMEDRIVE to "M:" (a mapped network drive) and my HOMEPATH to "\". Since I have read-only permissions for the root of that shared drive, I cannot create files or directories in my windows home directory. My attempts to work with the IT department have been unsuccessful. Is there a way for me to globally change these envars at boot or login time? I need for all applications to use alternate values (such as "C:" and "\Users\myname"). I have some installed utilities (like gvim and others) that store preference files in the user's home directory. IMPORTANT: Changing these envars under "System Properties Environment Variables" does not work. I have tried setting these as both User and System Variables (including a reboot). TypingSET HOMEin a DOS window clearly shows that my settings are ignored. Also, using "Start in" in a Windows shortcut will also not solve this, as I need things like Explorer context menu items (like "Edit with Vim") to operate correctly. I do have admin rights on this company laptop, but I am not a Win7 guru. Back in the day, a boot script would have solved this in a minute. Is it even possible today? Thanks.

    Read the article

  • Trying to limit IMAP folders/mailboxes my iPhone/iPad sees

    - by QuantumMechanic
    (Note: I am using dovecot 1.0.10 on Ubuntu 8.04.4 LTS. Yes, I know I need to upgrade before next year :) (Note: The SMTP/IMAP server in question only serves my family, so there's only a very few users. Certainly what I propose below, even it it works, would be a logistical nightmare with any significant number of users). I have noticed (and have confirmed via google) that the iOS mail app is terrible in its handling of IMAP subscriptions, namespaces, etc. For example, my iPhone and iPad will see EVERYTHING (all mailboxes, folders, etc.), whereas clients like Thunderbird, alpine, etc. only see what I tell them to see. This makes it an incredible pain to move mail between mailboxes because I have to scroll through a gazillion things. The mail_location in dovecot.conf is: mail_location = mbox:%h/Mail/:INBOX=/var/mail/%u To get around this, I've been considering doing the following for user foo: Create a dovecot userdb with a foo-ios virtual user in it, whose UID is identical to that of the real (in /etc/passwd) foo user and with a homedir of /home/foo-ios. ln -s /var/mail/foo /var/mail/foo-ios mkdir -p /home/foo-ios/Mail cd /home/foo-ios/Mail ln -s /home/foo/Mail/mailbox-i-want-visible mailbox-i-want-visible Make symlinks for the rest of limited set of mailboxes/folders I want visible to the iOS mail app. chown -R foo:foo /home/foo-ios Change iOS mail app settings to log in as user foo-ios instead of user foo. Will this work or will there be some index/file corruption hell because there will be two sets of indexes (one set living in /home/foo/Mail/.imap and other set living in /home/foo-ios/Mail/.imap) indexing the same underlying mbox files? And I'd be more than happy to hear of a better way to do this with dovecot! (Or to hear that dovecot 2.x works better with iOS devices).

    Read the article

  • Manual NAT on Checkpoint (Redirect all http requests to a local web server)

    - by B. Kulakli
    We have a proxy server in our internal network and I want to redirect all internet http requests to a web server in local network. It'll be like a Network Billboard that says "No direct connection is available. Set up your proxy etc." For example: A user starts the computer Opens the browser Tries to open www.google.com Should see web server output on local network Tries another web site on internet Should see web server output on local network Sets up proxy Tries to connect to a web site Web site should be loaded I have added a simple manual NAT rule to address translation in Checkpoint firewall but it simply does not work. Here is my address translation rule Source Destination Service T.Source T.Destination T.Service MY_PC A_GOOGLE_IP ALL ORIGINAL INT_WEB_SRV ORIGINAL Then when I ping A_GOOGLE_IP, replies come from INT_WEB_SRV, as I expected. However, when I try to connect A_GOOGLE_IP from browser (http://A_GOOGLE_IP), no replies come from SYN_SENT and falls into timeout. When I look at the firewall log of INT_WEB_SRV, I can see the incoming connection requests from MY_PC is accepted and NO denies. By the way, there is no problem to see INT_WEB_SRV (http://INT_WEB_SRV) from browser. My understanding is, my NAT rule at checkpoint NGX R60 does not include return packets. I definitely need some help.

    Read the article

  • Hyper-V vss-writer not making current copies

    - by Martinnj
    I'm using diskshadow to backup live Hyper-V machines on a Windows 2008 server. The backup consists of 3 scripts, the first will create the shadow copies and expose them, the second uses robocopy to copy them to a remote location and the third unexposes the shadow copies again. The first script – the one that runs correctly but fails to do what it's supposed to: # DiskShadow script file to backup VM from a Hyper-V host # First, delete any shadow copies of the drives. System Drives needs to be included. Delete Shadows volume C: Delete Shadows volume D: Delete Shadows volume E: #Ensure that shadow copies will persist after DiskShadow has run set context persistent # make sure the path already exists set verbose on begin backup add volume D: alias VirtualDisk add volume C: alias SystemDrive # verify the "Microsoft Hyper-V VSS Writer" writer will be included in the snapshot # NOTE: The writer GUID is exclusive for this install/machine, must be changed on other machines! writer verify {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} create end backup # Backup is exposed as drive X: make sure your drive letter X is not in use Expose %VirtualDisk% X: Exit The next is just a robocopy and then an unexpose. Now, when I run the above script, I get no errors from it, except that the "BITS" writer has been excluded because none of its components are included. That's okay because I really only need the Hyper-V writer. Also I double checked the GUID for the writer, it's correct. During the time when the Hyper-V writer becomes active, 2 things will happen on the guest machines: The Debian/Linux machine will go to a saved state and restore when done, all fine. The Windows guests will "creating vss snapshop-sets" or something similar. Then X: gets exposed and I can copy the .vhd files over. The problem is, for some reason, the VHD files I get over seems to be old copies, they miss files, users and updates that are on the actual machines. I also tried putting the machines in a saved sate manually, didn't change the outcome. I hope someone here has an idea of how to solve this.

    Read the article

  • Heartbeat/DRBD failover didn't work as expected. How do I make the failover more robust?

    - by Quinn Murphy
    I had a scenario where a DRBD-heartbeat set up had a failed node but did not failover. What happened was the primary node had locked up, but didn't go down directly (it was inaccessible via ssh or with the nfs mount, but it could be pinged). The desired behavior would have been to detect this and failover to the secondary node, but it appears that since the primary didn't go full down (there is a dedicated network connection from server to server), heartbeat's detection mechanism didn't pick up on that and therefore didn't failover. Has anyone seen this? Is there something that I need to configure to have more robust cluster failover? DRBD seems to otherwise work fine (had to resync when I rebooted the old primary), but without good failover, it's use is limited. heartbeat 3.0.4 drbd84 RHEL 6.1 We are not using Pacemaker nfs03 is the primary server in this setup, and nfs01 is the secondary. ha.cf # Hearbeat Logging logfacility daemon udpport 694 ucast eth0 192.168.10.47 ucast eth0 192.168.10.42 # Cluster members node nfs01.openair.com node nfs03.openair.com # Hearbeat communication timing. # Sets the triggers and pulse time for swapping over. keepalive 1 warntime 10 deadtime 30 initdead 120 #fail back automatically auto_failback on and here is the haresources file: nfs03.openair.com IPaddr::192.168.10.50/255.255.255.0/eth0 drbddisk::data Filesystem::/dev/drbd0::/data::ext4 nfs nfslock

    Read the article

  • ubuntu 9.10 installer doesn't recognize the hard drive

    - by dan
    I downloaded Ubuntu 9.10 x86_64 and am trying to install it on a fairly modern system with a Gigabyte GA-MA770-UD3 motherboard. Ubuntu 9.04 installed fine and still will when I stick that disc in, but 9.10 doesn't see my hard drive (western digital 250GB). If I boot from the disc, I can install gparted and it does recognize the drive, but when I try to start the install process from the live disc, Ubuntu again doesn't recognize the hard drive. I checked /var/log/messages and see this: Nov 12 17:28:08 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was bad, boot with 'nodmraid'. Nov 12 17:28:08 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: no raid sets and with names: "nvidia_ciiajheb-0" Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. I checked my BIOS, SATA is enabled and is set to IDE mode, so there shouldn't be software RAID, but nonetheless, I added nodmraid to the boot line and tried again. It still doesn't recognize the drive. I checked /var/log/messages again and now see this: Nov 12 17:49:38 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was boad, boot with 'nodmraid'. Nov 12 17:49:38 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Any ideas on things to try? I've tried all of the various BIOS settings for SATA. IDE,RAID, etc. Nothing seems to work.

    Read the article

  • LVM2 volume group lost

    - by MrG
    I updated one of my servers, but - although I took care not to modify - the volume groups on /dev/sdb1 were lost, although the physical volumes seem to be still there: [root@server ~]# pvscan PV /dev/sda2 VG VolGroup lvm2 [465,16 GiB / 0 free] PV /dev/sdb1 lvm2 [1,82 TiB] Total: 2 [2,27 TiB] / in use: 1 [465,16 GiB] / in no VG: 1 [1,82 TiB] [root@server ~]# pvs -v Scanning for physical volume names PV VG Fmt Attr PSize PFree DevSize PV UUID /dev/sda2 VolGroup lvm2 a-- 465,16g 0 465,16g HftbaD-MBs0-3p7D-6O13-CrzU-T9Gb-6W0ofB /dev/sdb1 lvm2 a-- 1,82t 1,82t 1,82t dD4XZP-WStA-61xV-5Sff-ifmW-R4rR-JenHoU [root@server ~]# pvck -d -v /dev/sdb1 Scanning /dev/sdb1 Found label on /dev/sdb1, sector 1, type=LVM2 001 Found text metadata area: offset=4096, size=1044480 Found LVM2 metadata record at offset=10752, size=1037824, offset2=0 size2=0 Found LVM2 metadata record at offset=9216, size=1536, offset2=0 size2=0 Found LVM2 metadata record at offset=7168, size=2048, offset2=0 size2=0 Found LVM2 metadata record at offset=5632, size=1536, offset2=0 size2=0 I attempted to fix it as described here and was able to extract the 4 meta data sets listed above (using i.e. dd bs=1 skip=5632 count=1536 if=/dev/sdb1 of=output.file), none of them includes the lv_data which I'm missing. Please advise how I could access the files which should be on /dev/sdb1 there. Any help is appreciated!

    Read the article

  • Alfa AWUSO36H 1W dysfunctional driver

    - by BrainStorm
    I recently purchased an Alfa AWUSO36H 1W wireless USB adapter for my notebook, in order to improve signal strength and quality. I'm currently using Linux Mint 11, and the it uses the RTL8187 driver for this adapter, I'm also using a 4dbi antenna, though I have others. The problem is that this adapter does exactly the opposite of what it should, actually my internal Broadcom BCM4313 adapter works way better than the alfa. Browsing is slow, some network applications don't even work, pings against Google.com on the internal adapter runs smooth, while in the alfa it gets like 25% packets lost or more! I'm less them 50 feet from my AP, the internal adapter gets 44/70 link quality, and the alfa gets around 60/70 (iwconfig output). Also the system always sets alfa power to 20dbm(100mw), then I have to do sudo iw set reg B0 to make it 30dbm(1000mw), but apparently no significant change. I've installed wireless-compat drivers, no change either. And worst of all, in Windows 7 it works way more smoothly for browsing, though I couldn't test it properly there. I hope its a driver problem, even if it's a pain to find/compile Linux drivers for a starter, I prefer it to a hardware problem where I would need to buy another adapter, since I have no money left (except for the cantenna pieces).

    Read the article

  • "could not find suitable fingerprints matched to available hardware" error

    - by Alex
    I have a thinkpad t61 with a UPEK fingerprint reader. I'm running ubuntu 9.10, with fprint installed. Everything works fine (I am able to swipe my fingerprint to authenticate any permission dialogues or "sudo" prompts successfully) except for actually logging onto my laptop when I boot up or end my session. I receive an error below the gnome login that says "Could not locate any suitable fingerprints matched to available hardware." What is causing this? here are the contents of /etc/pam.d/common-auth file # # /etc/pam.d/common-auth - authentication settings common to all services # # This file is included from other service-specific PAM config files, # and should contain a list of the authentication modules that define # the central authentication scheme for use on the system # (e.g., /etc/shadow, LDAP, Kerberos, etc.). The default is to use the # traditional Unix authentication mechanisms. # # As of pam 1.0.1-6, this file is managed by pam-auth-update by default. # To take advantage of this, it is recommended that you configure any # local modules either before or after the default block, and use # pam-auth-update to manage selection of other modules. See # pam-auth-update(8) for details. # here are the per-package modules (the "Primary" block) auth sufficient pam_fprint.so auth [success=1 default=ignore] pam_unix.so nullok_secure # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_ecryptfs.so unwrap # end of pam-auth-update config #auth sufficient pam_fprint.so #auth required pam_unix.so nullok_secure

    Read the article

  • Why does Facebook Chat through XMPP protocol on Pidgin Portable not authorize?

    - by Sara Neff
    I heard you can use facebook chat on desktops now. Thats awsome! What i didn't hear is that it is a pain in the butt! Not awsome! I've followed six nearly identical sets of instructions from six different websides, including the one that facebook generates for you, to get facebook chat connected through Pidgin. Its the latest portable version, so from what i hear the plugin is out of the question. Whenever I go to try and connect i get a message saying "Not Authorized" and buttons to either modify the account info, or retry. NOTHING i have done has fixed this, and I can't find anything remotely usefull anywhere. I am running windows xp, and running pidgin (portable) off of a flash drive. Someone please tell me what i have to do. I read about authorizing the chat on my actual facebook page. I'd have tried that if i could find out how to do it, but if its there they hid it good. HELP?!

    Read the article

  • Correct use of SMTP "Sender" header?

    - by Eric Rath
    Our web application sends email messages to people when someone posts new content. Both sender and recipient have opted into receiving email messages from our application. When preparing such a message, we set the following SMTP headers: FROM: [email protected] TO: [email protected] SENDER: [email protected] We chose to use the author's email address in the FROM header in an attempt to provide the best experience for the recipient; when they see the message in their mail client, the author is clear. To avoid the appearance of spoofing, we added the SENDER header (with our own company email address) to make it clear that we sent the message on the author's behalf. After reading RFCs 822 and 2822, this seems to be an intended use of the sender header. Most receiving mail servers seem to handle this well; the email message is delivered normally (assuming the recipient mailbox exists, is not over quota, etc). However, when sending a message FROM an address in a domain TO an address in the same domain, some receiving domains reject the messages with a response like: 571 incorrect IP - psmtp (in reply to RCPT TO command) I think this means the receiving server only saw that the FROM header address was in its own domain, and that the message originated from a server it didn't consider authorized to send messages for that domain. In other words, the receiving server ignored the SENDER header. We have a workaround in place: the webapp keeps a list of such domains that seem to ignore the SENDER header, and when the FROM and TO headers are both in such a domain, it sets the FROM header to our own email address instead. But this list requires maintenance. Is there a better way to achieve the desired experience? We'd like to be a "good citizen" of the net, and all parties involved -- senders and recipients -- want to participate and receive these messages. One alternative is to always use our company email address in the FROM header, and prepend the author's name/address to the subject, but this seems a little clumsy.

    Read the article

  • Manual NAT on Checkpoint (Redirect all http requests to a local web server)

    - by kulakli
    Hi, We have a proxy server in internal network and I want to redirect all internet http requests to a web server in local network. It'll be like a Network Billboard that say "No direct connection is available. Set up your proxy etc." For example: A user starts the computer Opens the browser Trys to open www.google.com Should see web server output on local network Trys another web site on internet Should see web server output on local network Sets up proxy Trys to connect to a web site Web site should be loaded I have added a simple manual NAT rule to address translation in Checkpoint firewall but it simply does not work. Here is my address translation rule Source Destination Service T.Source T.Destination T.Service MY_PC A_GOOGLE_IP ALL ORIGINAL INT_WEB_SRV ORIGINAL Then when I ping A_GOOGLE_IP, replies come from INT_WEB_SRV, as I expected. However, when I try to connect A_GOOGLE_IP from browser (http://A_GOOGLE_IP), No replies come from SYN_SENT and falls into timeout. When I look at the firewall log of INT_WEB_SRV, I can see the incoming connection requests from MY_PC is accepted and NO denies. By the way, there is no problem to see INT_WEB_SRV (http://INT_WEB_SRV) from browser. My understanding is, my nat rule at checkpoint NGX R60 does not include return packets. I definitely need some help. Regards, Burak

    Read the article

  • Shuffling in windows media player

    - by Crazy Buddy
    I think media player has several issues indeed. You see, I'll be hearing songs most of the time using WMP 11 (in WinXP SP3). Today - While I was wasting my time poking some sleepy questions in SE, I also noticed this... My "Now-playing" list contains some 500 mp3s (doesn't matter). I've enabled both Shuffle and Repeat. I play those songs. When I get irritated with some song (say - the 10th song), I change it. Something mysterious happened (happens even now). A sequence of atleast 3 songs (already played before the 10th song) repeat again in the same way following the selected one... Then, I skip those somehow and arrive at another boring song (say now - 20th) and now, the sequence would've increased by about 5 songs (sometimes)... Sometimes, I even notice a specific "sequence of songs" (including the skipped one) repeating again & again. I doubt most guys would've noticed. This makes me ask a question - Why? There are a lot songs in my playlist. Why the same sets of songs? Does WMP really chooses a sequence at start and follows it. Once a change is encountered, it starts the sequence again after several songs. Is it so? Feel free to shoot it down. I don't know whether it's acceptable here. Just curious about it... Note: This is only observed when both shuffle and repeat are enabled. To confirm, I tried it in two other PCs of mine (thereby dumped 2 hours). BTW, I also didn't observe this magic in VLC, Winamp, K-Lite and not even my Nokia cellphone. I think I'm not a good Googler and so, I can't find any such issues :-)

    Read the article

  • Routing for remote gateway over VPN in Vista/7 broken?

    - by Raymond
    Hi, Situation is as follows. Home computer running Windows 7, sets up VPN connection (LT2P + IPSec, "use remote gateway" disabled) to office. Subnet is 192.168.64.x Office has Draytek Vigor 2920 router, subnet is 192.168.32.x What happens? - VPN connection itself works fine - Can ping any machine on the remote network - When trying to open a webpage from a host in the remote network, the remote server logs the incoming request, but the browser hangs on "waiting for..." and eventually times out. I have observed this problem on Windows Vista and Windows 7. On Windows XP however there is no problem like described above. The only clue I have is that there is a difference in the routing between XP and Vista/7. The output of "route print" on Windows XP looks like this: (See www.latunyi.com/routing_xp.png) So here the gateway for the 192.168.32.x subnet is the IP address that the local computer has in the remote network. The output of "route print" on Windows 7 (and Windows Vista) looks like this: (See www.latunyi.com/routing_win7.png") Now the gateway for the 192.168.32.x subnet is the IP address of the VPN router (32.1). I don't know if that causes this trouble, but it seems a bit strange. Enabling "use default gateway on remote network" doesn't make a difference. Using the new option "Disable class based route addition" in Windows 7 only makes the route to the VPN router disappear. I am really puzzled here. I assume the VPN routing can't be broken in both Vista and Windows 7, and this should just work without manually adding routes. I hope someone has a solution for this problem :-). Thanks!

    Read the article

  • IIS 7, FastCGI, PHP and custom php.ini files

    - by Marlon
    I'm running PHP 5.3, FastCGI, and IIS 7 on Windows Server 2008. I have a site which I would like to configure its own php.ini settings for but things aren't working as expected. I am following the tutorial located here. This is what I have done so far: 1) Configured a new website with it's own AppPool. 2) Selected PHP 5.3.6 from the PHP Manager available on the website home on IIS (not the web server home which sets the global version of PHP) 3) Added the following lines to the section of the applicationHost.config file located at system32/inetsrv/config <application fullPath="C:\Program Files (x86)\PHP\v5.3\php-cgi.exe" arguments="-d open_basedir=C:\inetpub\wwwroot\kickasswebsite.com" maxInstances="4" idleTimeout="300" activityTimeout="30" requestTimeout="90" instanceMaxRequests="200" protocol="NamedPipe" queueLength="1000" flushNamedPipe="false" rapidFailsPerMinute="10"> <environmentVariables> <environmentVariable name="PHPRC" value="c:\inetpub\wwwroot\kickasswebsite.com" /> </environmentVariables> </application> 4) I then create a php.ini file located in C:\inetpub\wwwroot\kickasswebsite.com (the location of the root of the website) register_globals = on 5) I then run test.php which simply outputs everything the method call to phpinfo() returns. At this point, I observe that the global setting for register_globals = off (as it should be), but the local setting for register_globals = off, even though I specified it differently in the php.ini file I created at the root of the site. Furthermore, I see these settings in the output of the php.ini Configuration File (php.ini) Path C:\Windows Loaded Configuration File C:\Program Files (x86)\PHP\v5.3\php.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) What am I messing up on, or is there a different way to go about this?

    Read the article

  • domain user disabling screensaver

    - by RASG
    I have the following situation: Due to security reasons the screensaver is activated after 10 minutes, and immediately locks the screen. There are GPOs preventing the user from changing the screensaver parameters and the background image. In order to bypass the background policy, some users are using bginfo The problem is that for some reason now the screensaver doesn't work anymore. The settings are still the same (10 minutes; locked to the user) and comparing snapshots of the registry before and after executing bginfo doesn't show any significant modification. Any hints? EDIT 1: Ok, i figured whats going on, but now i have another question. bginfo refreshes the user settings by reading HKEY_CURRENT_USER\Control Panel\Desktop, which has ScreenSaveActive. If the user set it to 0, disables the screensaver. Why isnt HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\Control Panel\Desktop, which sets ScreenSaveActive to 1, being enforced? or if it is being enforced, where is bginfo storing the value 0, and how can it bypass the policy? EDIT 2: I also discovered that after setting any value to HKEY_CURRENT_USER\Control Panel\Desktop\ScreenSaveActive, it can be deleted and the last value will remain active. For some reason HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\Control Panel\Desktop\ScreenSaveActive value is not being enforced to the user.

    Read the article

  • "one-off" use of http_proxy in a Chef remote_file resource

    - by user169200
    I have a use case where most of my remote_file resources and yum resources download files directly from an internal server. However, there is a need to download one or two files with remote_file that is outside our firewall and which must go through a HTTP proxy. If I set the http_proxy setting in /etc/chef/client.rb, it adversely affects the recipe's ability to download yum and other files from internal resources. Is there a way to have a remote_file resource download a remote URL through a proxy without setting the http_proxy value in /etc/chef/client.rb? In my sample code, below, I'm downloading a redmine bundle from rubyforge.org, which requires my servers to go through a corporate proxy. I came up with a ruby_block before and after the remote_file resource that sets the http_proxy and "unsets" it. I'm looking for a cleaner way to do this. ruby_block "setenv-http_proxy" do block do Chef::Config.http_proxy = node['redmine']['http_proxy'] ENV['http_proxy'] = node['redmine']['http_proxy'] ENV['HTTP_PROXY'] = node['redmine']['http_proxy'] end action node['redmine']['rubyforge_use_proxy'] ? :create : :nothing notifies :create_if_missing, "remote_file[redmine-bundle.zip]", :immediately end remote_file "redmine-bundle.zip" do path "#{Dir.tmpdir}/redmine-#{attrs['version']}-bundle.zip" source attrs['download_url'] mode "0644" action :create_if_missing notifies :decompress, "zipp[redmine-bundle.zip]", :immediately notifies :create, "ruby_block[unsetenv-http_proxy]", :immediately end ruby_block "unsetenv-http_proxy" do block do Chef::Config.http_proxy = nil ENV['http_proxy'] = nil ENV['HTTP_PROXY'] = nil end action node['redmine']['rubyforge_use_proxy'] ? :create : :nothing end

    Read the article

  • Mac, VNC and multiple monitors

    - by MarqueIV
    I asked a similar question here before but apparently I wasn't as clear as I had expected by the responses. That said, I'll try again. I have a Mac Pro with quad monitors which I would like to access remotely. I've been using VNC for this (either via screen sharing or a dedicated VNC client), which works, but the VNC protocol matches the physical layout/resolutions of attached monitors. One of the things I like about Microsoft's Remote Desktop (Terminal Server) client is that when you connect, it blanks out the local screens and sets the resolution to a client-specified setting. In other words, when natively running Windows, even though I'm running a physical 30" monitor flanked by 2 24" monitors as well as a 21" Cintiq monitor, I can set the Remote Desktop resolution to match my notebook's screen giving me a native, single-monitor configuration. As soon as I disconnect (and you log back in locally), the desktop un-blanks and the resolution resets back to the four physically attached monitors. Again, VNC works and yes I know I can use 5901, 5902...n to attach VNC to a specific monitor as opposed to the entire desktop, but I'm still at the mercy of trying to look at a 2560x1600 resolution on a 1280x800 screen. I'm left with either scaling (everything's too small) or panning/scrolling (it's like playing hide-and-seek with your documents!) SO... anyone know of any Mac-based remote software (client and server) that will let me connect to my Mac Pro and reset the resolution by the client, just like you can in Windows, or am I SOL?

    Read the article

  • Can I boot up a virtual machine natively?

    - by Anshul
    My question is: Is is possible to run a virtual machine natively on your hardware if you have installed the proper drivers etc? In other words, can I use a VHD as a regular hard drive to boot from? The reason I want to do this is that I do both graphics-intensive and audio-intensive work, but my computer is not powerful enough to handle both at the same time and many times I install a bunch of audio programs that I don't want affecting the stability of my graphics programs. Basically I wanted to have sandboxing between the two sets of applications. So I tried running the graphics-intensive programs in a VirtualBox VM and the audio-intensive work natively (simply because it's a pain to route ASIO audio devices in/out of VirtualBox). This kind-of works - the graphics-intensive stuff is tolerable, but still relatively slow, because it's running inside a VM. So my next idea was to just dual-boot and install the graphics and audio programs in separate partitions but I frequently use them in tandem, so it wouldn't be practical to reboot my machine every time I need to use the other set of programs. But I could live with this scenario: If I need to do more audio-intensive stuff, I'll just boot up to the audio partition and run the graphics programs in a VM, and then when I'm working heavily on the graphics part, I'll just boot the graphics partition as a regular OS directly on the hardware. Is this possible? For example by booting up a VHD as a regular hard drive? Or by setting up dual-boot, and every time the audio partition is shut down, synchronize the graphics VM VHD with the native graphics partition? Is it practical, given the above scenario? And if it's not possible, barring buying another computer, can anyone suggest a best-of-all-worlds setup (the two worlds being performance, sandboxing, and running in parallel) for the above scenario? Thanks in advance.

    Read the article

  • How can you force the start and end date of a task in Microsoft Project to be on the same day?

    - by Hauke P.
    I have a task called "Interview person A about topic X". The task's duration is set to 2 hours. The start date of the task should automatically be calculated taking dependencies and resource availabilities into account. My question boils down to: How can I force this task to start and end on the same date? Background: In my case, Microsoft Project sets the start date to a Friday at 5pm. As my working hours are set to 8am to 12am and 1pm to 6pm (Mon-Fri), Microsoft Project "splits up" the task at 6pm on Friday and plans to continue it at 8am on the following Monday. However, it does not make any sense to stop the interview on a Friday and restart it on Monday. Therefore the automatic suggestion is not helpful in this case. That's why I'm looking for a way way to force the task to start and end on the very same day. (In my example, I'd like Microsoft Project to delay the start date of the task until Monday 8am as this is the first time slot in which the task "fits in completely".) By the way: I have lots of such cases... for that reason it would be really great if there was a solution that doesn't just deal with this single special case.)

    Read the article

  • Converting a Windows 2003 server

    - by Jim Bass
    We have a legacy database system based upon MS SQL running on Windows Server 2003. The client software will only run on Windows XP. We have recently had success converting a client into a virtual machine and running it under Fusion on Mac minis. So far, it is working incredibly well. So well, in fact, that we are now considering trying to convert the server to a virtual machine. This raises several questions, though: 1. The server uses a raid array. Does the VM virtualize the raid array? I only ask because in my experience Windows products don't like it when you change core hardware. 2. Is there any reason why running SQL server on a virtual machine won't work? It will be up 24/7. 3. Is there a different converter for servers? 4. Will I have to track down the licensing for MS SQL and Server 2003 or will they come across ok? 5. The company that designed the software is no longer in business. There is some fear that the software is somehow tied to the hardware configuration. We bought the hardware, but their engineers came out and configured the system. Will the virtual machine be able to spoof particular chip sets? Thanks! Jim Bass

    Read the article

  • How to create a mysql database that can contain any character, also different languages

    - by Jakke
    I'm trying to create a database that has to contain articles in different languages. I'm using Mariadb as my server and I know bits of SQL. My knowledge doesn't really cover details like the differences between engines like MyISAM, InnoDB etc or character sets like utf8/16/32, latin 5/7/etc. I do know that the character set has importance, I guess what I'm looking for is an all-encompassing character set and an engine that best deals with this type of content. Also, is there an advantage in storing articles in multiple data rows (equivalent of different pages) to make things a little faster, or would you store a whole article in a single data row. Or does that depend on the size of the articles? Sorry for my noobish question, I know the information is all out on the internet but it would take me quite a long time to research and get a grip on everything. Would be cool if someone with experience could give me a little head start and point me in the right direction. This is for a intranet site, consider the content to be somewhat like a blog (and no, I don't want wordpress or something similar at this point). Not sure if it matters, but I tend to create and manipulate my tables with phpmyadmin, I use apache as web server and it all runs on Linux.

    Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >