Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 162/216 | < Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >

• Virtual machines interconnection inside Proxmox 2.1 Cluster

  - by Anton

  We have 3 physical servers (each with 1 NIC) in different datacentres, all of them are interconnected by openvpn bridged private network (10.x.x.x). Inside this network we have fully functional 3 nodes Proxmox 2.1 cluster. So, actually question is: Is there any "proper" way to make "global" local network (172.16.x.x) for all VMs inside cluster, so even if we move VM from one node to other we could reach it by static IP regardless of it's physical location? BTW, we can't add dedicated NIC to each server. Thanks in advance. EDIT: I have tried to make a separate openvpn bridge for 172.16.x.x, now I have at each server two interfaces: SRV1: openvpnbr1 - 172.16.13.1 vmbr0 - 172.16.1.1 SRV2: openvpnbr1 - 172.16.13.2 vmbr0 - 172.16.2.1 But now there is no connection between those ifaces: SRV1: ping 172.16.13.2 From 172.16.1.1 icmp_seq=2 Destination Host Unreachable SRV2: ping 172.16.13.1 From 172.16.2.1 icmp_seq=2 Destination Host Unreachable If I shut down vmbr0 interfaces, so there is connection between servers over openvpn, but vmbr0 is used by Proxmox... Where I am wrong?

  Read the article

• How to get started with tcp/ip v6?

  - by Johan

  Hi Now and then there is "news" about that the ip numbers will run out in X years, and we must change to tcp/ip v6... And even thou this crisis never really happens it has waken a question, how do you get started with tcp/ip v6? What can I do at home and is this a good or bad idea? Can you use IPv4 and IPv6 in the same cables in the same LAN, or do you need to physically separate them? Can you have some translation box so you can reach the "normal" internet from the IPv6 connected devices? (Just like a NAT-Router) Can someone please clarify the situation a little bit? Thanks Johan

  Read the article

• How can I view my IIS hosted sites on other machines on my network

  - by Truegilly

  Hello, at home i have a simple network setup conatining 2 machines and 1 belkin router. On one machine i have a site hosted with IIS7. Rather than the standard localhost/index.htm address i have added an entry in the HOSTS file pointing the local ip (127.0.0.1) to this domain - www.mysite.dev. i can access the site with www.mysite.dev with no problem. what i would like to do is be able to view this site from my other machine on the network. initially i assumed this could be done with a url like so MACHINE-NAME/www.mysite.dev, but the connection always times out. But I can ping MACHINE-NAME without problems. For testing purposes i have diabled the windows firewall on both machines but to no joy. Like a typical web developer, my techy/network skills are pretty poor. Can anyone see where im going wrong ?? thank you for your time Truegilly :)

  Read the article

• Analyze a wireless network that constantly drops/has speed issues

  - by Eddie Parker

  Hello, I'm curious what the best tools are to use for analyzing problems with a WiFi network. Here's the scenario: I have a WiFi router (Belkin N+) that's setup in AP mode. I have three RT-N13U's that I've purchased to use as 'repeaters', but I've had so many problems when more than one of them is running (bad routes) that I've only got one active. Sometimes certain boxes on my network can't talk to others, and drops are quite frequent and quite aggravating. I'm running Mac, Windows, and Linux (Gentoo) boxes on this network, so any software, or steps I should take that work for any of those boxes should be sufficient. Apologies if this is answered somewhere else - I'll close it as a dupe if so.

  Read the article

• VNC on Xen failure

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• Forward one RDP port on one machine to multiple external users at the same time

  - by matnagel

  We have a windows server 2003 machine with rdp service listening on the standard port 3389. For security reasons this port is not opened on the router, but we have freesshd service running and a remote admin can login via ssh and this port is forwarded to external port 33001 for the first external user. This works great. Now we have another admin who wants to work remote (he uses a different windows account, but needs to work on the same machine.) So this is basically a ssh port forwarding question. Will the other user be able to login at the same time using the same port 33001 ? Please keep in mind that there will be a second tunnel, and this second tunnel will also use the local port 3389 on the windows server.

  Read the article

• wireless access point

  - by Warren Bullock III

  I'm hoping to get some suggestions for possible Wireless Access point/router models which will allow us to have two separate networks. We run an internal network on 10.x.x.x IP range where we have shares and other network resources for which we would like to have our regular users access. However, we would also like to offer a separate wireless network for guests which ideally would be on 192.168.x.x and these users would not be able to see any of the resources sitting on the 10.x.x.x network. Anyone have any recommendations on single devices that might be able to get the job done? I was looking at the Linksys E4200 and it seems to support what I'm looking to do... any others? Thanks in advance for any suggestions.

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Why does TeamViewer launch a web server?

  - by OverTheRainbow

  Hello I just read this article which I find concerning: "After 90 minutes of troubleshooting, Nash traced the problem to TeamViewer, which he used to remotely administer the client's servers. It turns out the program had opened up its own webserver on the client's machine as soon as Apache went down and in the process made it impossible for the client, a large provider of business software, to restart its proper website." http://www.theregister.co.uk/2009/07/24/teamviewer_snafu/ I started using TeamViewer recently because it's just much better than UltraVNC (runs on both XP and Vista, the server dials out instead of requiring the user to open a port on their router + better performance than UVNC)... but I thought that TeamViewer had both the server and client connect out to TV's web server for data to flow between the two hosts. Why does TV even need to open a web server on the server host? Thank you.

  Read the article

• Shaping outbound Traffic to Control Download Speeds with Linux

  - by Kyle Brandt

  I have a situation where a server makes lots of requests from big webservers all at the same time. Currently, I have not control over the amount of requests or the rate of the requests from the application that does this. The responses from these webservers is more than the internet line can handle. (Basically, we are launching a DoS on ourselves). I am going to get push to get this fixed at the application level, but for the time being, is there anyway I can use traffic shaping on the Linux server to control this? I know I can only shape outbound traffic, but maybe there is a way I can slow the TCP responses so the other side will detect congestion and this will help my situation? If there is anything like this with tc, what might the configuration look like? The idea is that the traffic control might help me control which packets get dropped before they reach my router.

  Read the article

• Wireless printer going offline upon entering power save mode

  - by Regmi

  I recently bought a printer, Samsung ML1865W, a wireless laser printer. It works very well, wirelessly until after a while, it goes to power save mode when the printer goes offline. I then cannot connect to the printer (pinging the ip and various ports associated with it do not give any response) until I power cycle the printer. I have checked my wireless settings and my router, I have installed the printer software in WinXP, Win2000 and in Mac and the printer behaves just the same. Any ideas if the printer hardware itself is broken or that its something on my network/application side that's the culprit. If you own the printer, have you had any trouble like that at any time?

  Read the article

• Can't ping some IP addresses in the same subnet (LAN) Windows 2011 Server

  - by Ricardo

  Hi I’m running in Windows Small Server 2011 server standard (192.168.1.108), it’s my dhcp and dns server too, but suddenly all other users can’t get internet. My gateway is 192.168.1.1. After a lots of tested I can saw that my server can’t get into the router (192.168.1.1), and also into some others computers, but some other computers answer the ping command. In fact the same computer with the IP 192.168.1.9 didn't answer, but with the IP 192.168.1.63, it response! I have no routers, firewall, vlans or anything that disallow the traffic between computers, in fact when I changed the server IP address (192.168.1.109), I be able to ping the other computers and gateway, but if a back to the 192.168.1.108 the trouble comeback. I hope you can help me with this issue Ricardo

  Read the article

• Configure Nginx On Separate Server For Zimbra Webmail

  - by alphadogg

  How do I properly configure a server with nginx to front for a Zimbra server with multiple domains? I run a small SOHO network. I NAT/port forwarding on my Comcast router to get traffic to my handful of servers. I setup a server with Zimbra, call it host1.internal.local. The server currently has two domains, call them domain1.com and domain2.com. Both offer webmail access at webmail.domain1.com and webmail.domain2.com. I have a separate server with nginx. I want to configure nginx to reverse proxy, such that I can direct all HTTP/HTTPS, and send webmail traffic via matched host address/headers to the Zimbra server. If possible, I'd like to know how to map IMAP, POP and SMTP traffic too. How would I do this?

  Read the article

• TCP failure on Solaris

  - by anurag kohli

  Hi All, I recently ran into a problem where a Solaris server could not establish a TCP socket on port 2126. From a packet capture I see this (note: A is a Solaris server, B is a router): A sends SYN to B B sends SYN, ACK to A Notice A (Solaris) does not acknowledge the SYN from B. Due to the business impact of the problem, I had to reboot the server to fix the problem. That said, I want to know the next time the problem occurs, what can I do to get a root cause (ie before server reboot)? Thanks in advance.

  Read the article

• TightVNC grey screen?

  - by gary

  I'm trying to help my mom remotely with some PC problems. She's not too computer savvy, so to keep the firewall stuff on my side of things, I tried to use a reverse VNC connection: On my machine, I set up TightVNC client in listening mode. I also opened TCP port 5500 on my router and firewall, and checked it using http://canyouseeme.org/. On her machine, I (instructed her to) set up TightVNC server, and connect to my machine's IP ('Add New Client...'). Both machines run Windows XP & TightVNC 1.3.10. The problem: When she tries to connect, a TightVNC window with grey background pops up on my machine, but I never get to see the remote desktop. It just remains grey. However, it seems that I control the mouse on the remote side (she says it's moving). I tried to reverse-connect from another machine on my LAN and it works without a problem. Any idea what the problem could be?

  Read the article

• Creating self-signed SSL on IIS - Remote access problem

  - by ile

  I followed these instructions to create self-signed ssl: http://www.visualwin.com/SelfSSL/ (I opened SelfSSL and typed selfssl /T) When I access https: //localhost/ than it works, but when I try to access it remotely (i set up my router to port forward to localhost), for example https: //myip the page does not load. Also, I noticed one other thing. When I access localhost locally then I am asked to enter user/pass, but if I access remotely the I get the following warning: Under Construction The site you were trying to reach does not currently have a default page. It may be in the process of being upgraded and configured. ... I don't know if it is related with this but I hope someone know the answer. Thanks, Ile

  Read the article

• Wireless network unavailable, no networks found after Windows update

  - by jacobsee

  Old Dell Inspiron 8200 laptop with Linksys Wireless G network adapter card (WPC54G v2). Wireless connection was working fine. Then I ran a bunch of windows updates, I think the last one was the recent .NET 3.5 service pack update. Now wireless networks won't connect. Using windows to manage wireless, no networks show up. I'm typing right now on another laptop where wireless is working fine. I've restarted router & Dell laptop several times. Tried to Repair wireless connection and refresh network list. Also restarted DHCP and WZC service, all to no avail. I then uninstalled .NET 3.5 SP (don't remember number) and .NET 3.0 SP2. I don't remember all the windows updates that I just ran because I haven't used this laptop in a while so had to catch up on some updates.

  Read the article

• Splitting Ethernet cable

  - by Nathan

  I am looking for the best way to network my small business. I have an office where my router/modem are located, and then 2 more computers in another room. I can route Ethernet to this room with about 75 ft of cabling, and I would like to do this because my computers on Ethernet are getting 3x the speed as computers on wireless. Is there any way I can use just one Ethernet cable to span the 75 feet, and then maybe 2 smaller ones to go to the two computers from there? If there's a simple way to do this, maybe with a connector that would be ideal, as opposed to buying over 150 ft of cabling. Thanks!

  Read the article

• Block a URL at browser level

  - by Farseeker

  Does anyone have a solution (that doesn't involve editing the hosts file) to block a particular URL from FireFox? Basic back story is that I'm trying to discipline myself. I'm spending FAR too much time over at Server Fault that I want to genuinely block the site from my work PC so that every time I find myself flicking to it during work time I can't see it, but I'd like to be able to disable it during my lunch break. (So I only spend 40 minutes a day there, rather than 4 hours). That said I don't want to block it at the router, nor for anyone else.

  Read the article

• European wireless data

  - by drewk

  I am on my way to Europe for 20 days with the wife and teenage kids. Among us, we have 3 iPhones, 1 Blackberry, 2 iPad 3G and 2 Macbook Pro laptops. Each has Skype. I am very concerned about AT&T data charges, and I am looking for a sensible alternative. For example, the AT&T data plans for the phones and iPads are $200 EACH for 200 MB per device. That is $1,200 and does not even cover the laptops. Ouch!!! I am thinking about a prepaid data plan from a European cell system of some sort combined with a GSM data modem and a Cradlepoint router, such as the CTR500. So, questions: 1) Anyone know of a GSM data source in Europe where I can buy a GSM Modem compatible with the CTR500 at a reasonable prepaid rate? 2) Experience with the CTR500?

  Read the article

• Slash Notation IP - What is what?

  - by Nirmal

  We just signed up with a new ISP and we got a static IP from them. Our previous ISP just gave one IP and we were able to configure our web server using that. Now, we have got this new IP with a slash notation. This type is new to me. When I used the CIDR calculator, it gave me the following results: 202.184.7.52/30 IP: 202.184.7.52 Netmask: 255.255.255.252 Number of hosts: 2 Network address: 202.184.7.52 Broadcast address: 202.184.7.55 Can someone please help me by explaining what these are? I could not understand what the number of hosts means. Is that telling that I can use two different IP for DNS (A) records? Also, which one should I setup in my router? The network address or broadcast address? Thank you very much for any answer you may provide.

  Read the article

• Newbie one: Virtual Networks - Hyper-V - Remote Destktop - Only one phisical NIC

  - by josecortesp

  Hello everyone, I'll try to explain my situation and I'll apreciate any help: I have a phisical server (quad core, 4Gb ram, 1TB raid 10, etc) with Win Server 2008 R2 enterprise, running IIS, Printing, etc... Also, I want to set up 2 virtual Servers with 2008 R2 standart one with SQL Server and the other with Team Foundation. What i need is: Being able to access from inside the private phisical network, to Remote Desktops on each of the Virtual and the phisical Servers Had Access from the outside, using a router and port Forwarding, to the TFS server and the IIS server (one is virtualized, the other is phisical) This is it, but note that I only have one Phisical Nic. How do I configure this to work. When i set up the hyper-v role, on the wizard something like it showed up but I don't remmember what i choose, and right now, I cannot access none of the servers from remote desktop, not even from the phisical private network. Can anybody point me, what can i do? Thanks in advance (sorry 4 my english, i'm a spanish talker and my english isn't that good)

  Read the article

• How to access website on localhost from internet?

  - by Nitesh Panchal

  Hello, I turned my pc into router by allowing port forwarding on port 80 and got my hostname(xyz.donexist.org) registered through dyndns.com. Now i when i type my public ip address in browser i get redirected to my browser. I have installed glassfish and have my website deployed in glassfish. I want that when i type xyz.donexist.org my website should be opened. What all steps more i need to take? I have made a entry in etc/hosts file as :- 127.0.0.1 xyz.donexist.org Please guide me. I am and beginner. Thanks in advance :)

  Read the article

• Drawbacks of installing linux on usb stick?

  - by Znarkus

  I am setting up a router/nas/http/whatever server based on an ION mini-ITX board. I've installed Ubuntu Server on an old 160 GB drive, but it generates a lot more heat and vibrates more than my other new drive (storage). It just doesn't fit the concept, and worse: it takes up a SATA port. As SSD's are crazy expensive I'm thinking of buying an extra 4 GB USB stick, and raid0 it. From my point of view, these are the pros/cons: Pros Low power consumption No vibrations No heat Smaller Get to buy new, larger USB stick (:D) Cons Shorter life time Slower Raid 0 More work maintaing/installing? I think the pros overweighs the cons. Shorter life time and raid 0 is countered by regular backups of the configs/settings. Slower is partially countered by raid 0, and I don't know about the last one. What do You think? Experience? Another solution?

  Read the article

< Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >