Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 160/216 | < Previous Page | 156 157 158 159 160 161 162 163 164 165 166 167  | Next Page >

• Setting up Windows SBS 2008 network on Xen

  - by samyboy

  I'm trying to install a Windows SBS 2008 server in a Xen environment. The OS is booting fine. Unfortunately I can't figure out how to set up the network settings. Dom0 is a Debian Lenny hosting around 10 virtual servers. Here are the settings I'm using in the hosted Windows SBS: IP address: 10.20.0.8 Network mask: 255.255.0.0 Gateway: 10.20.0.1 Note that during the installation stage, Windows set the net mask at 255.255.255.0 without letting me choose. Gross. Windows SBS tells me I have a "limited connection". I can't ping the gateway nor any other IP except localhost and it's own IP (10.20.0.8). Here is the Xen config file: kernel = '/usr/lib/xen-3.2-1/boot/hvmloader' builder = 'hvm' memory = '4096' device_model='/usr/lib/xen-3.2-1/bin/qemu-dm' acpi=1 apic=1 pae=1 vcpus=1 name = 'winexchange' # Disks disk = [ 'phy:/dev/wnghosts/exchange-disk,ioemu:hda,w', 'file:/mnt/freespace/ISO/DVD1_Installation.iso,ioemu:hdc:cdrom,r' ] # Networking vif = [ 'mac=00:16:3E:0A:D0:1B, type=ioemu, bridge=xenbr0'] # video stdvga=0 serial='pty' ne2000=0 # Behaviour boot='c' sdl=0 # VNC vfb = [ 'type=vnc' ] vnc=1 vncdisplay=1 vncunused=1 usbdevice='tablet' This config is working with others Windows XP domU's. I tried to change the ne2000 values with 0 and 1 with no effect. I am far from having good Windows administration skills so I guess I definitely need some help on this case. Thanks.

  Read the article

• How to set up DHCP-configured access through a Linux box?

  - by marcusw

  I would like an old desktop box to use my laptop as a router to access the internet. Here is my setup: I have one ethernet port in the side of my laptop which I want to use to get internet access to my desktop computer. The laptop is connected to the LAN via a wireless link. Both systems run Linux. The desktop autoconfigures itself using DHCP. The laptop is a Kubuntu system. I do not have any crossover cables, though wireshark on the laptop sees the DHCP requests from the desktop just fine, so I doubt that I need one. What do I have to do to make this work?

  Read the article

• Acer Aspire 3680 Wireless Signal Problem

  - by SHiNKiROU

  I am using Acer Aspire 3680. I recently reinstalled Windows Vista, and the wireless did not work by default. I installed the "Atheros Wireless LAN Driver" on this site: http://support.acer-euro.com/drivers/notebook/as_3680.html The result, the wireless APs are successfully scanned. However, when I tried to join a network, even with 5/5 signal, an error message showed up diagnosing signal too little. I restarted as Ubuntu, and wireless worked perfectly, with same computer position. Even more confusing, When I moved to the kitchen (2 meters close to the router), the wireless connected, when I move back to my room, wireless failed on Vista and worked on Ubuntu. It is clearly the driver problem. Acer laptops seems come with pre-installed drivers, but after re-installation, they are all gone. (I can't find the original Acer backup disc) Please do not answer "move closer to the AP" and something related to "interference", as wireless worked with Ubuntu's default driver.

  Read the article

• is my ddclient conf right ?

  - by Luc

  Hello, I bought my domain.tld and like to have it points toward my home server. I then created a zoneedit account and setted the zoneedit dns in my domain setting in my registrar web interface. I then installed ddclient on a machine behind my router, with the following conf: Configuration file for ddclient generated by debconf # /etc/ddclient.conf protocol=zoneedit1 use=if, if=eth0 server=www.zoneedit.com login=my_zoneedit_login password=my_zone_edit_password domain.tld When I open a browser and check http://domain.tld I have a site under contruction (from registrar dotsterparking). Is my ddclient conf correct ? Where can I find the errors (while updating my IP) if any ? Thanks a lot, Luc

  Read the article

• Network config for KVM on physical machine with single NIC and single public IP

  - by neo0

  I have a physical machine running CentOS 6.4 and I will rent a place to run it in a data center. I want to install KVM on that machine to run some virtual machines. The problem is my physical machine have only one NIC and the data center give me a public IP for that interface. So how should I configure network on the physical machine to make it assign for each vm a private IP that can connect to Internet. If I create a br0 bridged with eth0 interface and create a vm with option --bridge=br0 then KVM could not assign an IP for the vm so setup can not be done. Should I use NAT mode? Does KVM have any host-only network like Virtualbox? But the vm still has to connect to outside? Thank you! Update I install the guest network using NAT (--network network:default) and then I only have to port-forwarding from the host. But if I config br0 bridged with physical eth0 then the guest can not get an IP from boot. So I removed the br0 and it worked.

  Read the article

• Intel Atom overheating in ASUS EEE Box 1501P

  - by Sergey L.

  I have had an ASUS EEE Box 1501P for just a little bit over a year. Of course it breaks 2 months after the warranty runs out. http://www.asus.com/Eee/EeeBox_PC/EeeBox_PC_EB1501P/ I have been using the box as a Home Media Center. Running mostly 24/7 often pausing a video overnight. Since last week the fan started running extremely loud. After some digging I found that the Intel Atom CPU in it is overheating and the built-in sensor is reporting temperatures way over 105°C. This got me worried, so I took the unit apart. Completely vacuumed the heat sink, oiled the fan, but the unit is still showing the same behaviour. After turning it on and just observing the hardware monitor in the BIOS the temperature slowly rises from 40°C to over 95°C in appx 5 min. I am running the newest BIOS and a lightweight Linux OPENELEC OS with XBMC on it. Now I am wondering if it could be a faulty heat sensor in the Atom. Recommended running temperature is up to 85°C, but I have not detected any performance hits when running at the above mentioned 105°C and there seem to be no software faults. How can an Atom with an attached heat sink and a fan running at full capacity even get this hot in the first place at 0 load? Aren't those things designed to generate virtually no heat? Could it be a faulty heat sensor? What shall I try to fix this? I would prefer not to damage the CPU, since it is hard fused into the motherboard and cannot be replaced. I could remove the heat pipe/heat sink, but it is getting hot, so heat is properly transferring from the CPU to the heat pipe, the fan is running at full capacity, is recently oiled and warm air is making it out of the exhaust. Edit: One more note: The North-bridge (or whatever it is called nowadays) is on the same heat pipe.

  Read the article

• How can I express this nginx config as apache2 rewrite rules?

  - by codecowboy

  if (!-e $request_filename){ rewrite /iOS/(.*jpg)$ /$1 last; rewrite /iOS/(.*jpeg)$ /$1 last; rewrite /iOS/(.*png)$ /$1 last; rewrite /iOS/(.*css)$ /$1 last; rewrite /iOS/(.*js)$ /$1 last; rewrite /Android/(.*jpg)$ /$1 last; rewrite /Android/(.*jpeg)$ /$1 last; rewrite /Android/(.*png)$ /$1 last; rewrite /Android/(.*css)$ /$1 last; rewrite /Android/(.*js)$ /$1 last; rewrite ^/(.*)$ /?route=$1 last; } There are some vanity URLs e.g. mysite.com/yourdetails which are handled internally by a router class (its a PHP app with index.php as the entry point) and they seem to work fine on nginx but not Apache :-/ I tried this but the vanity URLs are not working RewriteEngine On RewriteBase / RewriteCond %{REQUEST_URI} !=/favicon.ico RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ index.php?route=$1 [L] I'd like to rule out Apache config first before I get too deep into the code.

  Read the article

• GlusterFS is failing to mount on boot

  - by J. Pablo Fernández

  I'm running the official GlusterFS 3.5 packages on Ubuntu 12.04 and everything seems to be working fine, except mounting the GlusterFS volumes at boot time. This is what I see in the log files: [2014-06-13 08:52:28.139382] I [glusterfsd.c:1959:main] 0-/usr/sbin/glusterfs: Started running /usr/sbin/glusterfs version 3.5.0 (/usr/sbin/glusterfs --volfile-server=koraga --volfile-id=/private_uploads /var/www/shared/private/uploads) [2014-06-13 08:52:28.147186] I [socket.c:3561:socket_init] 0-glusterfs: SSL support is NOT enabled [2014-06-13 08:52:28.147237] I [socket.c:3576:socket_init] 0-glusterfs: using system polling thread [2014-06-13 08:52:28.148183] E [socket.c:2161:socket_connect_finish] 0-glusterfs: connection to 176.58.113.205:24007 failed (Connection refused) [2014-06-13 08:52:28.148236] E [glusterfsd-mgmt.c:1601:mgmt_rpc_notify] 0-glusterfsd-mgmt: failed to connect with remote-host: koraga (No data available) [2014-06-13 08:52:28.148251] I [glusterfsd-mgmt.c:1607:mgmt_rpc_notify] 0-glusterfsd-mgmt: Exhausted all volfile servers [2014-06-13 08:52:28.148477] W [glusterfsd.c:1095:cleanup_and_exit] (-->/usr/lib/x86_64-linux-gnu/libgfrpc.so.0(rpc_transport_notify+0x27) [0x7fe077f8e0f7] (-->/usr/lib/x86_64-linux-gnu/libgfrpc.so.0(rpc_clnt_notify+0x1a4) [0x7fe077f91cc4] (-->/usr/sbin/glusterfs(+0xcada) [0x7fe078655ada]))) 0-: received signum (1), shutting down [2014-06-13 08:52:28.148513] I [fuse-bridge.c:5444:fini] 0-fuse: Unmounting '/var/www/shared/private/uploads'. My fstab contains: proc /proc proc defaults 0 0 /dev/xvda / ext4 noatime,errors=remount-ro 0 1 /dev/xvdb none swap sw 0 0 /dev/xvdc /var/lib/glusterfs/brick01 ext4 defaults 1 2 koraga:/private_uploads /var/www/shared/private/uploads glusterfs defaults,_netdev 0 0 Any ideas what's going on and/or how to fix it?

  Read the article

• Using AddEncoding x-gzip .gz without actual files

  - by STATUS_ACCESS_DENIED

  With Apache (2.2 and later) how can I achieve the following. I want to transparently compress using GZip encoding (not plain Deflate) the output when a certain file is queried with its name plus the extension .gz, where the .gz version doesn't physically exist on disk. So let's say I have a file named /path/foo.bar and no file foo.bar.gz in the folder to which the URI /path maps, how can I get Apache to serve the contents of /path/foo.bar but with AddEncoding x-gzip ... applied to the (non-existing) file? The rewrite part appears to be easy, but the problem is how to apply the encoding to a non-existent item. The other way around also seems to be simple as long as the client supports the encoding. Is the only solution really a script that does this on the fly? I'm aware of mod_deflate and mod_gzip and it is not what I'm looking for - at least not alone. In particular I need an actual GZIP file and not just a deflated stream. Now I was thinking of using mod_ext_filter, but couldn't bridge the gap between rewriting the name of the (non-existent) file.gz to file on one side and the LocationMatch on the other. Here's what I have. RewriteRule ^(.*?\.ext)\.gz$ $1 [L] ExtFilterDefine gzip mode=output cmd="/bin/gzip" <LocationMatch "/my-files/special-path/.*?\.ext\.gz"> AddType application/octet-stream .ext.gz SetOutputFilter gzip Header set Content-Encoding gzip </LocationMatch> Note that the header for Content-Encoding isn't really needed by the clients in this case. They expect to see actual GZIP files, but I want to do this on-the-fly without caching (this is a test scenario).

  Read the article

• "The directory name is invalid" when trying to install drivers in Windows 7 via Device Manager

  - by Luke

  First off, this computer is not mine, it's a customer's system. Having said that... The hard drive was moved to a new motherboard, CPU, RAM combo, and booted up fine. Customer puts in driver CD, drivers won't load. He brings it into me. Under Device Manager for Windows 7 x64, I see lots of PCI to PCI bridge, one SMBus Controller, and about 20 Unknown Devices. Greeeeeat... So I start with the SMBus driver directly from the Asus website for the motherboard (P8H77-M Pro). If I install from the setup program, it tells me to reboot, then it starts the install. It gets half way through the setup, then fails (An unknown error occurred. Setup will exit). When I try to point to the folder from Device Manager, it starts copying files for the driver, even presents me with the proper name of the device, but says that an error has occurred there as well: The directory name is invalid. Doing some Googling, I saw that many people had this issue with Vista. K, Vista and 7 are similar, maybe the solutions are the same... But they aren't. I tried: Copying the entire driver folder and setup utility to the Program Files folder and running it / selecting it in DM Downloading another set of drivers in case this one is corrupt Disabling UAC Deleting and recreating the %WINDIR%\TEMP folder Removing all references to previous hardware that I could find, even in Device Manager's hidden mode So far, nothing has worked. A wipe and reload will be out of the question

  Read the article

• How can I route packets from one application to a virtual machine in windows 7?

  - by user836045

  I am trying to test an application running in windows 7, and I would like to send the packets it generates to a server VM (I am using virtualbox) on the local machine which will act as a simulation for when packets will be really sent over the internet to a distant server. I need to check for correctness of the packets in certain situations. Is there a way on windows to take packets produced by an application and instead of passing it to my router, pass it along to another process, i.e. my virtual machine. I'd prefer not to change any of the code on my application and would rather find an outside solution. Is there such a solution for windows 7?

  Read the article

• Two identical fiber optic broadband lines working as one

  - by Katafalkas

  I have been trying to find an answer to this, but all I can find is hobbyists trying to connect their Linksys devices to get some magic out of them. I am looking for a way I could combine two 100Mbit fiber optic lines into a single connection for our office. I assume it involves some Cisco learning or something similar. Do I need to configure some big router to load-balance the NATing in some way? I assume that many of you have done something similar and hope someone could share their knowledge or at least provide me some tips on how to do this.

  Read the article

• Manage MS SQL server over SSH (putty)

  - by adopilot

  There is great implementation of PuttY for Symbian S60 devices, and last versions of Nokia phones with full QWERTY keyboard offers comfort for using Putty and SSH goodies. I start wondering is there a way to access MSSQL over SSH and send T-SQL commands. I am able to connect my router which running on FreeBSD OS, also other CentOS server with MYSQL are able to me over SSH. I want to try access MS-SQL-2005 from my mobile phone, Probably this is not going to have daily use, it is just for geeky and justification to myself: why I had to buy so expensive a toy

  Read the article

• DNS resolution over DHCP

  - by Eric

  I have a m0n0wall router a VMWare workstation running ubuntu a windows 7 workstation running the VM The ubuntu hostname is "renraku" From the windows machine I can't resolve dns automatically for this host. For example, when I ping renraku Ping request could not find host renraku. Please check the name and try again. However nslookup seems to work nslookup renraku Server: m0n0wall.local Address: 192.168.123.254 Name: renraku Address: 192.168.123.248 I don't get how to have ping to work with hostnames. The main goal behind this is to have my web server to work with hostnames instead of ip addresses EDIT : ping 192.168.123.248 works

  Read the article

• Setting a Static IP Running FreeBSD8 in VirtualBox hosted on Windows 7

  - by gvkv

  I'm using VirtualBox on Windows 7 (host) to run a FreeBSD (guest) based web server. I`ve assigned a static ip of 192.168.80. 1 to the (virtualized) NIC which is run in bridged mode. The problem is that when I ping an external server (such as google.com) I get a No route to host error: dimetro# ping google.com PING google.com (66.249.90.104): 56 data bytes ping: sendto: No route to host ... I can ping the BSD server from both another virtualized machine and my host machine and from the server, I can ping everything on the network. The router ip is 192.168.1.1/16. ADDENDUM: I have the following lines in /etc/rc.conf on the BSD VM to configure networking: defaultrouter="192.168.1.1" ifconfig_em0="inet 192.168.80.1 netmask 255.255.0.0"

  Read the article

• Process for configuring network settings on a headless rack mount device

  - by PherricOxide

  I'm with a small company that plans to sell a rack mounted network appliance which is configurable via a web interface (think of a router configuration page sort of deal), and I'm wondering in large data center like environments what the process usually is for the initial setup of such systems. The main question is, if the system is headless, how do you get initial remote access to it? Do companies usually first plug a server into a monitor/keyboard/mouse in order to configure the network settings before mounting it in a rack? How else would they know what the IP address of the machine was if DHCP (and it can't be hard coded because of IP conflict potential)?

  Read the article

• ICS as guest in Ubuntu 12.04 host

  - by oshirowanen

  I have installed Android as per this guide as a guess os via VirtualBox: http://www.android-x86.org/documents/virtualboxhowto Using the following ISO: android-x86-4.0-RC1-eeepc.iso But I am unable to connect to the internet from within the android virtual machine. The host OS is Ubuntu 12.04 where the internet works fine. I have internet access via a usb wireless connection to the home router. All this is fine. If I install Ubuntu 12.04 as a guest, where the host is also Ubuntu 12.04. The guest os'es internet works fine out of the box. But for some reason, I can't get the above androids internet to work out of the box as the guest os. Anyone know what I am doing wrong?

  Read the article

• Why would image thumbnails not be showing in all search engines in all browsers?

  - by Edward Tanguay

  For over a week now, when I search for a word at Google, it correctly gives me some preview image thumbnails: But when I click on "images", it doesn't show me any thumbnails: The same thing happens at Bing.com, when I search Bing itself it gives me some thumbnails on the general search result page: But when I click on "images", it doesn't show me any thumbnails: The same thing happens at Yahoo: If I click on one of the broken thumbnails, it shows me the picture fine: Thumbnails at youtube also work fine: It seems each search engine is hanging on different URLs as shown above: t1.gstatic.com ts3.mm.bing.net thm-a02.yimg.com so it doesn't seem to be the problem of one specific URL not sending thumbnails, it is just a problem with search engine image thumbnails in general. Also, this happens in every browser I try: Explorer, Firefox, Chrome. What could be the problem? Is it my computer, some setting somewhere, my router, my Internet provider (T-Online, Germany)? Has anyone ever had this problem and solved it?

  Read the article

• Ubuntu to Ubuntu VNC over SSH tunnel

  - by rxt

  I have a Linux Ubuntu desktop at home, ssh enabled, vnc server installed, router rule configured. It all works, and at home I can connect via the local network from my Mac. From the outside I can login via ssh. I've configured putty as follows: session: host name and port number connection ssh tunnel: forwarded ports: L5900|192.168.0.23 the local address is: 192.168.1.45 When I make the connection I can login to the remote machine. Then I open Remote Desktop Viewer. I click connect protocol: vnc host: ? use host as ssh tunnel: ? I don't know what to use for the last two options. Which ip-addresses should I use?

  Read the article

• DYNDNS setup with TightVNC on Windows Server 2008 R2

  - by StealthRT

  Hey all, i seem to be having a problem with getting ports to forward on my Windows Server 2008 R2 PC. I already set all my port forwarding for 5900/5800 on my router for my PC's IP address (192.168.1.22) but when i try to use the TightVNC PFPortChecker on port 5900 it tells me its not opened! I can not even connect to my DYNDNS server name (xxxxxxx.dyndns.org). As a side note, i am running Windows XP SP3 within a VirtaulBox inside Windows Server 2008 R2 but running the PFPortChecker in Windows 2008 R2 brings the same results as it does in the VM. I also added them to the Windows Firewall Advanced Security form to add those inbound ports for full access. What could i possibly be missing? Thanks for your time! David

  Read the article

• WEP key not working on laptop running Ubuntu

  - by stupid-idiot

  I can't connect to my router via wifi from my laptop (running Ubuntu) even if I'm 100% sure the WEP key I punch in is correct. It works via LAN though. I'm also not able to ping localhost 127.0.0.1. I had some problems setting up the radio on my network card but I think that that works since it finds some wireless networks. (Although it's much much faster than Windows it's useless since I can't download any libraries for development.) What could be wrong with my setup?

  Read the article

• Chipset fan on the frtiz - compressed air hasn't fixed anything - is there anything I can do?

  - by Anthony

  Yesterday, my computer started to make an annoying whining noise. Knowing that this is likely a fan issue, I opened the case and proceeded to determine which fan was causing the issue. I got some compressed air and tried cleaning out the dust around it (and the rest of the computer while I was at it). This hasn't seemed to fix the issue. Now, if it were just any fan, I would probably just replace the fan - they're relatively cheap after all. However, this is a special fan. Aside: For what its worth, I feel bad that the graphics card blocks part of the fan, but it is the only slot the graphics card fits, so I had no choice. After pulling out my motherboard user guide, it looks like this is a fan placed directly on top of the chipset. To be perfectly honest, I have no clue what the purpose of the chipset is - but it sounds important. After some quick research, I see that it is responsible for providing the bridge between my CPU, RAM and graphics, among other things. Just a quick search at Newegg tells me that chipset fans can be purchased at pretty reasonable prices (< 20 dollars). Is it practical to replace this fan? It is an old computer as computers go and I wouldn't be terribly upset to upgrade the motherboard and processor, so perhaps this is a sign. Hardware Specs: Motherboard: Asus A8N-E Chipset: NVIDIA nForce4 Ultra

  Read the article

• How should I remotely manage Dell Poweredge 2850 running Ubuntu server?

  - by Saul

  First I've got to say I'm a Linux / Ubuntu novice, so go gentle on me as I'm on day 3. I've managed to get Ubuntu server Ubuntu 8.04 LTS installed and running on the Poweredge 1850 I bought off ebay. The box will go in a rack at my office but I want to be able to work on it and power on and off from home and I gather that (maybe) IPMI over LAN might be the way to do this, or maybe its something to do with BMC or something? I want to be able to administer/manage from a client PC at home running XP. I will be configuring the office router to port forward port 80 and 443 to the Ubuntu server running Apache2, and I'm puzzled about how the remote management works (unless it comes on a different port forwarded to a different internal IP) Thanks for any help

  Read the article

• Internet Connection Sharing on OSX causes delayed web requests

  - by Vanthel

  I have an iMac connected to my router via WiFi, and a PC connected by ethernet to the iMac. The iMac is sharing its connection. I've never had a problem with this in the past (pre Lion anyway) but now all web page requests take an eon to resolve on the iMac (they are instant on the PC). It suggests to me the iMac is attempting to resolve it through the PC first every time? I've tried reordering the connections in the network settings but that made no difference.

  Read the article

• Can OpenVPN invoke DHCP Client?

  - by Ency

  I have got working VPN connection through openvpn, but I would like to use also my DHCP server and not openvpn's push feature. Currently everything works fine, but I have to manually start dhcp client, eg. dhclient tap0 and I get IP and other important stuff from my DHCP, is there any directive which start DHCP Client when connection is established? There is my client's config: remote there.is.server.com float dev tap tls-client #pull port 1194 proto tcp-client persist-tun dev tap0 #ifconfig 192.168.69.201 255.255.255.0 #route-up "dhclient tap0" #dhcp-renew ifconfig 0.0.0.0 255.255.255.0 ifconfig-noexec ifconfig-nowarn ca /etc/openvpn/ca.crt cert /etc/openvpn/encyNtb_openvpn_client.crt key /etc/openvpn/encyNtb_openvpn_client.key dh /etc/openvpn/dh-openvpn.dh ping 10 ping-restart 120 comp-lzo verb 5 log-append /var/log/openvpn.log Here comes server's config: mode server tls-server dev tap0 local servers.ip.here port 1194 proto tcp-server server-bridge # Allow comunication between clients client-to-client # Allowing duplicate users per one certificate duplicate-cn # CA Certificate, VPN Server Certificate, key, DH and Revocation list ca /etc/ssl/CA/certs/ca.crt cert /etc/ssl/CA/certs/openvpn_server.crt key /etc/ssl/CA/private/openvpn_server.key dh /etc/ssl/CA/dh/dh-openvpn.dh crl-verify /etc/ssl/CA/crl.pem # When no response is recieved within 120seconds, client is disconected keepalive 10 60 persist-tun persist-key user openvpn group openvpn # Log and Connected clients file log-append /var/log/openvpn verb 3 status /var/run/openvpn/vpn.status 10 # Compression comp-lzo #Push data to client push "route-gateway 192.168.69.1" push "redirect-gateway def1"

  Read the article

< Previous Page | 156 157 158 159 160 161 162 163 164 165 166 167  | Next Page >