Search Results

Search found 4462 results on 179 pages for 'ssh'.

Page 164/179 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

  • Linux VLAN Bridge

    - by raspi
    I have home network with VLANs, one for LAN, one for WLAN and one for internet. I'd like to use bridging so that instead of configuring these same VLANs to every machine, they had own VLAN ID and bridges were LAN, WLAN and internet. I've tried it but for some reason keep-alive/ttl seems to get broken because SSH sessions etc suddenly disconnects. We have this same setup working in workplace for 4+ years with 100+ customers but it's custom firewall/router hardware so accessing it is impossible. I know that it runs Linux. So what is Debian/Ubuntu default network settings doing wrong or is it just NIC driver/hw problem? I've tried to mess araund with ttl etc settings without any luck. The bad stuff is happening in the bridge because current VLAN-only setup works fine. interfaces: auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 allow-hotplug eth1 iface eth0 inet static iface eth1 inet static auto vlan111 auto vlan222 auto vlan333 auto vlan444 auto br0 auto br1 auto br2 # LAN iface vlan111 inet static vlan_raw_device eth0 # WLAN iface vlan222 inet static vlan_raw_device eth0 # ADSL Modem iface vlan333 inet static vlan_raw_device eth1 # Internet iface vlan444 inet static vlan_raw_device eth0 # LAN bridge iface br0 inet static address 192.168.0.1 netmask 255.255.255.0 bridge_ports eth0.111 bridge_stp on # Internet bridge iface br1 inet static address x.x.x.x netmask x.x.x.x gateway x.x.x.x bridge_ports eth1.333 eth0.444 bridge_stp on post-up iptables -t nat -A POSTROUTING -o br1 -j MASQUERADE pre-down iptables -t nat -D POSTROUTING -o br1 -j MASQUERADE # WLAN bridge iface br2 inet static address 192.168.1.1 netmask 255.255.255.0 bridge_ports eth0.222 bridge_stp on Sysctl: net.ipv4.conf.default.forwarding=1

    Read the article

  • virtualbox instances dedicated-server with custom dnsmasq

    - by ovanes
    I have dedicated server where I planned to run virtualbox virtual machines. Since the VMs are managed with vagrant/chef I may end up with many different ones. I thought it would be a great idea to deploy a dnsmasq on the server, which is going to dynamically assign the ip addresses to the VMs. Since each Vagrant/Chef recipe is configured to set the VM's host name I can find/reference the appropriate VM by the host name. Finally, the entire infrastructure is not directly accessible via internet, so the dedicated Server is the OpenVPN host. So the entire infrastructure may be seen as: +-------------------------------------+ | Dedicated Server | | | | +-------------+ +------------+ | +------------------+ | | DNSMasq | | OpenVPN |<==========>| Client | | +-------------+ +------------+ | | | | ^ ^ | +------------------+ | | | | | +--+ | | | | +-------+ | | | | VM1 | | | | +-------+ | | | ... | | | +-------+ | | +-| VM2 | | | +-------+ | +-------------------------------------+ Now some questions which I am struggling with: Are there any other suggestions to access private infrastructure, because I don't want to reinvent the wheel. On the Dedicated Server I don't see the vboxnet0 interface but VirtualBox is installed without GUI. Accessing of virtual boxes via ssh works fine. Did I miss smth? DNSMasq must serve the local VMs only, otherwise there is a chance that local DNSMasq start to serve other server's on the network, what I don't want. Because I don't see vboxnet0 I tend to use no-dhcp-interface=eth0 config option. Are there any thoughts on that despite, the fact that a second NW-card (which is not the case), might start serving DHCP-Requests? How should I config the VM's network interface that I am able to access it via OpenVPN and resolve the hostnames using the DNSMasq. I think it should be the host-only network card. Should I do bridging in the OpenVPN config or is it sufficient to use routing.

    Read the article

  • Linux/hostapd: AP can ping clients, clients can access internet, can't access www@wlan1 with more than 5-6 packets at once

    - by mhambra
    Please edit the title, can't make it sound better. -- OP. Hi all, I have a Wifi USB dongle in a PC, that serves as an AP for laptop. wlan1: 192.168.2.1, netmask 255.255.255.0, routed: route add -net 192.168.2.0 netmask 255.255.255.0 gw 192.168.2.1 ping 192.168.2.2 (laptop): ping was ok for lot of packets. Now, I try to access 192.168.2.1:80/myindex.html (apache) from laptop, and can see that own 1kb test page. But, trying to access 192.168.2.1:80/my.jpg, I see the following: GET /my.jpg HTTP/1.1 200 OK <jpg header, about a kilobyte> <TCP packet retransmisson> <TCP packet retransmisson> <end of stream> It seems to be a hostapd's problem (networked stuff worked fine with Ad-Hoc), but it may be also forwarding/routing problem too. What to google for? Even more strange, SSH to that host works fine.

    Read the article

  • mysql thread count

    - by Ryan M.
    We have a web application that uses apache and mysql. Generally (according to Munin) our MySQL thread count sits between 2 and 4 at all times. The other day, our server almost came to a halt. HTTP requests were slow or wouldn't go through at all, SSH would work, but would take 30+ seconds to register keystrokes, etc.. So we pull up Munin and the only thing that's out of normal boundaries is the Mysql thread count. CPU usage was under 1%, load was under 1.0, plenty of available RAM. As mentioned before, the thread count floats around 2 to 4. At the time of our slow downs it had spiked to 14. So I start poking around the Internet and I see that in most cases, you'll start to see a higher thread count when you start running into slow queries. If I understand it correctly, the request comes in that takes a while to process, in the mean time other requests are coming in, so a new thread will be created to work on the request (yes?). But at the time of the slow down, we had 0 slow queries. My question is: What else can cause mysql to create additional threads. And would this sudden spike in threads possibly cause the server to slow down? To fix the issue, we restarted apache and everything went back to it's beautiful, normal self. Considering the the Server Vitals (CPU, RAM, Network, etc) were all ideal, and the thread count was the only thing out of place, this seems like the most logical thing to pursue as the possible cause. If it matters, we're on Mysql 5.1.40. Server is FreeBSD 7.2 and the server in question is inside a jail.

    Read the article

  • vmware esxi 5, cant create snapshots and consolidate fails, how to delete old or consolidate redo logs?

    - by Scott Szretter
    I have a VM that seems to be working ok, but when VMWare DR (or I) tries to create a snap shot, it fails, and when I view the summary page of the VM it has a warning at the top showing that the disks need to be consolidated. So I go to snapshot manager for the VM and choose consolidate (in snapshot manager, there are no snapshots actually listed by the way). If fails with this error: This virtual machine has 255 or more redo logs in a single branch of its snapshot tree. The maximum supported limit has been reached, creating new snapshots will not be allowed. To create new snapshots, please delete old snapshots or consolidate the redo logs. If I browse the data store (which has plenty of free space, 2 TB and this vm is under 40gb), in the vm folder, I do in fact see a bunch of files, numbered all the way to 0255: myvm-000255-ctk.vmdk myvm-000255-delta.vmdk myvm-000255.vmdk How can I clean all this up? Is there an SSH command line command or can I delete some of the files safely? Thanks!

    Read the article

  • Execute remote shell commands on windows XP embedded

    - by BartD
    The following situation: We have Windows XP Embedded clients that have all admin shares disabled and only have read-only shares (for security reasons). What we want to do is run remote shell (dos) commands on these machines. At first we looked at PsExec & BeyondExec applications (and all sorts of variants), but all of them rely on having at least an admin$ share, which are disabled on our systems. Telnet is not secure enough, as is RSHD servers. So we looked at the next obvious solution: and SSH server. We also prefer an open-source or freeware solution that is still maintained. I looked at freeSSH server for Windows, but that didn't run stable, I tried installing copSSH, WinSSH & openSSH for Windows, but none of these applications seem to work on Windows XP Embedded. The services can either not be installed or cannot be started. I don't know why. Some kind of dependency that is missing. So are there any other solutions out there? I don't care about having to an agent installation locally of some kind on each system, as long as the size of the software is small enough. Can someone suggest some alternatives to what I've already mentioned? Thank you very much.

    Read the article

  • Can't install xclip on Ubuntu 10.10

    - by wildster
    I'm trying to load an SSH key to Github from a new machine and this command is not working: sudo apt-get install xclip Reading package lists... Done Building dependency tree Reading state information... Done Package xclip is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package xclip has no installation candidate when I try: sudo aptitude install xclip Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done No candidate version found for xclip No candidate version found for xclip The following partially installed packages will be configured: synaptics-dkms 0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0B of archives. After unpacking 0B will be used. Writing extended state information... Done Setting up synaptics-dkms (1.1.1) ... Loading new synaptics-1.1.1 DKMS files... Error! Cannot locate /usr/src/synaptics-1.1.1.dkms.tar.gz. File does not exist. dpkg: error processing synaptics-dkms (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: synaptics-dkms E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up synaptics-dkms (1.1.1) ... Loading new synaptics-1.1.1 DKMS files... Error! Cannot locate /usr/src/synaptics-1.1.1.dkms.tar.gz. File does not exist. dpkg: error processing synaptics-dkms (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: synaptics-dkms Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Any idea how I can install this? Mucho thanks in advance

    Read the article

  • Proper web server setup

    - by DMin
    I just got myself a slicehost basic slice to play around with so I can learn how to setup web-servers. I have Ubuntu 10.04.2 installed on the server. I was able to successfully get the server up and running from scratch, these were the things I did - following this tutorial. I know this is probably just a starters tutorial, so, I was wondering if you guys can tell me what you like to do while setting up production servers. These are the steps that were followed : Update and Upgrade Ubuntu sudo apt-get install apache2 php5-mysql libapache2-mod-php5 mysql-server Backup a copy of and edit apache2.conf Set : 'ServerTokens Full' to 'ServerTokens Prod''ServerSignature On' to 'ServerSignature Off' Backup php.ini and then Change “expose_php = On” to “expose_php = Off” Restart Apache Install Shorewall firewall Configure Shorewall to only accept HTTP and SSH connections(in the rules file) Enable shorewall on startup Add the website to the server : sudo usermod -g www-data root sudo chown -R www-data:www-data /var/www sudo chmod -R 775 /var/www I want make this CommunityWiki but can't seem to find the option to do it. Please feel free to add any feedback on the processes and things I am doing right/wrong. Much appriciated, thanks! :)

    Read the article

  • openvpn problem

    - by Jared Voronik
    I have a problem with openvpn. I have already setup openvpn sucessfully on some other servers in the past (basic configuration, nothing special). On this server, I used the same config file, but for setting up nat iptables -t nat -A POSTROUTING -s 10.4.0.0/24 -o eth0 -j MASQUERADE doesn't work. It gives error: iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How do I fix this error? Also, if I can't fix this error, can I do bridging instead of routing? I have only 1 interface, and I can connect to remote server only via ssh (and need to avoid reboots if at all possible) so if briding means a whole ethernet card has to be devoted to the openvpn (and no other servers) then briding is out, otherwise I can use briding. Do you know of a simple, step by step guide to configure openvpn briding (just simple openvpn server and clients that can access internet through vpn server, nothing fancy)?

    Read the article

  • Heartbeat/DRBD failover didn't work as expected. How do I make the failover more robust?

    - by Quinn Murphy
    I had a scenario where a DRBD-heartbeat set up had a failed node but did not failover. What happened was the primary node had locked up, but didn't go down directly (it was inaccessible via ssh or with the nfs mount, but it could be pinged). The desired behavior would have been to detect this and failover to the secondary node, but it appears that since the primary didn't go full down (there is a dedicated network connection from server to server), heartbeat's detection mechanism didn't pick up on that and therefore didn't failover. Has anyone seen this? Is there something that I need to configure to have more robust cluster failover? DRBD seems to otherwise work fine (had to resync when I rebooted the old primary), but without good failover, it's use is limited. heartbeat 3.0.4 drbd84 RHEL 6.1 We are not using Pacemaker nfs03 is the primary server in this setup, and nfs01 is the secondary. ha.cf # Hearbeat Logging logfacility daemon udpport 694 ucast eth0 192.168.10.47 ucast eth0 192.168.10.42 # Cluster members node nfs01.openair.com node nfs03.openair.com # Hearbeat communication timing. # Sets the triggers and pulse time for swapping over. keepalive 1 warntime 10 deadtime 30 initdead 120 #fail back automatically auto_failback on and here is the haresources file: nfs03.openair.com IPaddr::192.168.10.50/255.255.255.0/eth0 drbddisk::data Filesystem::/dev/drbd0::/data::ext4 nfs nfslock

    Read the article

  • Java: very slow tomcat and too big war file

    - by NaN
    I created some sort of RESTful API backend for a mobile app. It's written completely in Java using Jersey as Framework. At the moment no database is used, it's all in the memory, but this is no problem so far (it's only for prototyping purposes). I ordered the smallest package from digital ocean and installed tomcat7. All in all tomcat works, but I have three major problems: 1) It takes a long time until tomcat deploys the app: I deploy it per tomcat manager and it takes about 2 minutes unit the site works (excl. war upload time). 2) The war files are quite big (16MB): I don't know why they are so big. There are no database dependencies and most logic is written in plain java. Okay, we are using jersey, but 16MB are a lot for the logic of a small webservice. 3) I have to restart tomcat all 3 days or so. It looks like a memory leak or something similar. If the app runs for a few days the response time is quite high and the server seems to be frozen. It works again, if I restart tomcat per ssh. You can find my mvn pom file right here. Do you have some tips? Are there good tomcat alternatives?

    Read the article

  • How can I remotely display images on my computer?

    - by Jakob
    What I Have: A laptop booted with Ubuntu and a stationary computer dual-booted with Ubuntu and Vista, both connected through a wireless ad-hoc network. What I Want: I want a way to display images in fullscreen on my stationary, using my laptop as a "remote control". I want to be able to choose another picture at any time and have my stationary computer remain in fullscreen mode at all times. Preferably, I should also be able to display just an empty (black) screen. How can I arrange for this? What I Have Tried: I have tried simply SSH:ing into my stationary computer and opening the image files using an image viewer, but all of the ones that I have tried (Eye of Gnome, Mirage, Gwenview, and others) open a new window for every new image. I don't know how to force them into using a single instance. I have tried using the VLC remote control command line interface, but apart from seeming somewhat unreliable (exiting with segmentation faults at one point), it also displays some images with a green border and forces me to pause playback in order for the image to remain on screen. Bonus Question: In my final setup, I also need to play music through my stationary computer's speaker and have the ability to switch to another track at any point, like with the images. Preferably, I would like to control the images and the audio through the same interface. How can I best achieve this?

    Read the article

  • Is there a way to prevent password expiration when user has no password?

    - by Eric DANNIELOU
    Okay, we all care about security so users should change their passwords on a regular basis (who said passwords are like underwear?). On redhat and centos (5.x and 6.x), it's possible to make every real user password expires after 45 days, and warn them 7 days before. /etc/shadow entry then looks like : testuser:$6$m8VQ7BWU$b3UBovxC5b9p2UxLxyT0QKKgG1RoOHoap2CV7HviDJ03AUvcFTqB.yiV4Dn7Rj6LgCBsJ1.obQpaLVCx5.Sx90:15588:1:45:7::: It works very well and most users often change their passwords. Some users find it convenient not to use any password but ssh public key (and I'd like to encourage them). Then after 45 days they can't log in as they forgot their password and are asked to change it. Is there a way to prevent password expiration if and only if password is disabled? Setting testuser:!!:15588:1:45:7::: in /etc/shadow did not work : testuser is asked to change his password after 45 days. Of course, setting back password expiration to 99999 days works but : It requires extra work. Security auditors might not be happy. Is there a system wide parameter that would prompt the user to change expired password only if he really has one ?

    Read the article

  • ESXi 5 VM Putty session hangs, vSphere client timing out

    - by user192702
    First of all I believe this is a ESXi issue but let me know if you have seen this. It started about a year ago when I noticed occasionally when I putty via SSH to my VM guests, if I do anything that makes it to display a lot of things at once, the session will hang and I have to start a new one quite often only to find the same behaviour. What I meant by display a lot of things can be any of the following: 1) tail -f filename 2) Paste a long command 3) less filename If I type in one character at a time this won't happen. I tried searching online and it always point me to flow control settings and the various suggestions I've tried have never been able to resolve the issue. Since last week, I've noticed I'm not able to connect to my POP3 server from Outlook (it's timing out from Outlook's perspective). Today I tried to connect to the ESXi via vSphere client and it gives me a time out also. Exact behavior and error I saw is similar to the one posted at the following URL but the suggested technique also failed to resolve the issue. http://davidcocke.blogspot.hk/2012/02/unable-to-login-with-vsphere-client.html Has anyone experienced this before? Any suggestions on how to troubleshoot this?

    Read the article

  • Browsing \\computer\share fails, but net use \\computer\share works?

    - by JMD
    I've had mixed results with using Windows Explorer to browse remote file shares. The setup: I'm at work on Windows XP SP3 Files are at home on Windows XP SP3 Two separate VPNs are available to access my PC at home corporate OpenVPN (10.1.2.3) a Hamachi/LogMeIn connection (5.1.2.3) With respect to my problem, it doesn't matter which IP I use. They both perform exactly the same way: I expect that if I open Windows Explorer and type in \\10.1.2.3\Shared I should be interrupted with a challenge for credentials, and then be able to interact with the files in the share. However, I just get that annoying dialog, "Windows cannot find '\10.1.2.3\Shared' Check the spelling and try again, or try searching for the item ..." However, I can take that exact same computername/sharename and with net use I can: net use * \\10.1.2.3\Shared * /user:homecomputername\username with this result: Type the password for \\5.69.83.158\C$: Drive Z: is now connected to \\5.69.83.158\C$. The command completed successfully. I can then access the files in Z: in Windows Explorer which was my original intent. Even after Z: is already mapped and the credentials are cached I still cannot bring up \\10.1.2.3\Shared in Windows Explorer. Why does the latter work, but not the former? Edit: Other services work fine, such as RDP. (I have a problem in which I can't SSH home, but I'll consider that separately.)

    Read the article

  • IP6 seems to be enabled - How do I configure it without interfering with IP4?

    - by Mister IT Guru
    I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

    Read the article

  • Find slow network nodes between two data centers

    - by 2called-chaos
    I've got a problem with syncing big amount of data between two data centers. Both machines have got a gigabit connection and are not fully occupied but the fastest that I am able to get is something between 6 and 10 Mbit = not acceptable! Yesterday I made some traceroute which indicates huge load on a LEVEL3 router but the problem exists for weeks now and the high response time is gone (20ms instead of 300ms). How can I trace this to find the actual slow node? Thought about a traceroute with bigger packages but will this work? In addition this problem might not be related to one of our servers as there are much higher transmission rates to other servers or clients. Actually office = server is faster than server <= server! Any idea is appreciated ;) Update We actually use rsync over ssh to copy the files. As encryption tends to have more bottlenecks I tried a HTTP request but unfortunately it is just as slow. We have a SLA with one of the data centers. They said they already tried to change the routing because they say this is related to a cheap network where the traffic gets routed through. It is true that it will route through a "cheapnet" but only the other way around. Our direction goes through LEVEL3 and the other way goes through lambdanet (which they said is not a good network). If I got it right (I'm a network intermediate) they simulated a longer path to force routing through LEVEL3 and they announce LEVEL3 in the AS path. I basically want to know if they're right or they're just trying to abdicate their responsibility. The thing is that the problem exists in both directions (while different routes), so I think it is in the responsibility of our hoster. And honestly, I don't believe that there is a DC2DC connection which only can handle 600kb/s - 1,5 MB/s for weeks! The question is how to detect WHERE this bottleneck is

    Read the article

  • Is there any way to force my Linux box to always boot up with a self-assigned IP address?

    - by Jeremy Friesner
    This is perhaps an unusual request: I'm trying to get a Debian Linux box to always give itself a self-assigned IP address (i.e. 169.254.x.y) on boot. In particular, I want it to do that even when there is a DHCP server present on the LAN. That is, it should not request an IP address from the DHCP server. From what I can see in the "man interfaces" text, there is an option for "manual", and an option for "dhcp". Manual assignment won't do, since I need multiple boxes to work on the same LAN without requiring any manual configuration... and "dhcp" does what I want, but only if there is no DHCP server on the LAN. (A requirement is that the functionality of these boxes should not be affected by the presence or absence of a DHCP server). Is there a trick that I can use to get this behavior? EDIT: By "no manual configuration", I mean that I should be able to take this box (headless) to any LAN anywhere, plug in the Ethernet cable, and have it do its thing. I shouldn't have to ssh to the box and edit files to get it working each time it is moved to a different LAN.

    Read the article

  • RTNETLINK answers: File exists... maybe because assigned a new mac adress

    - by steven
    I got a "RTNETLINK answers: File exists Failed to bring up eth0:1" on "ifup eth0:1". I suspect it happens because i assigned a new mac adress in my VM's network adapter. Can you tell me how to fix the issue? My configuration looks like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.1.80 netmask 255.255.255.0 gateway 192.168.1.1 dns-nameservers 192.168.1.1 # Alias being connected to 192.168.10.x Network auto eth0:1 allow-hotplug eth0:1 iface eth0:1 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 Why do I get "RTNETLINK answer: File exists.." suddenly? I worked with this configuration before without problems. All i did in the past is to renew the adapters mac adress. At the moment I am connected to the 192.168.10.x Network and if I do /etc/init.d/networking stop /etc/init.d/networking start then i got "RTNETLINK [...] falied to bring up eth0:1" but the strage thing is that i am able to connect to 192.168.10.83 via ssh from my host machine. But I cannot reach the internet from the debian client. I hope it is clear what my problem is, now. update if i change my /etc/network/interfaces like this then "ifup eth0" fails, too with the same error! # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 with verbose option enabled i got: Configuring interfache eth0=eth0 (inet) run-parts --verbose /etc/network/if-pre-up.d ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0 RTNETLINK answers: File exists Failed to bring up eth0. same if i type this manually: ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0

    Read the article

  • Converting flv and mp4 video format to '.ogg' using FFmpeg

    - by user163906
    I have HostGator VPS server with FFmpeg installed. It allows me to convert .wmv to .flv as well as .mp4 files successfully using the following commands for flv and mp4: ffmpeg -i WantsABath.wmv -b 600k -r 24 -ar 22050 -ab 96k WantsABath.flv ffmpeg -i WantsABath.wmv WantsABath.mp4 but it won't allow me to convert any file format to .ogg. I tried using the command: ffmpeg -i input.mp4 -acodec libvorbis -vcodec libtheora -f ogv output.ogv by mondain but no luck with it. I am doubting that my VPS doesn't have libtheora installed. I tried configuring it by using SSH but I don't know how to make sure if it is installed or not. I tried checking with php_info but can't find anything regarding libtheora. Here's my FFmpeg version: FFmpeg version SVN-r19795, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --enable-libmp3lame --enable-libvorbis --disable-mmx --enable-shared --prefix=/usr/ --enable-gpl libavutil 50. 3. 0 / 50. 3. 0 libavcodec 52.35. 0 / 52.35. 0 libavformat 52.38. 0 / 52.38. 0 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 1 / 0. 7. 1 This details doean't show libtheor Can anyone please suggest me something?

    Read the article

  • Freebsd jail for an small company - checklist - what shouldn't forget

    - by cajwine
    Looking for an checklist for an "small company freebsd/jail server". Having pretty common starting point: FreeBSD jail (remote/headless) for the company: public web, email, ftp server, and private (maybe in the future partially public) wiki (foswiki) 4 physical persons, (6 email addresses) + one admin - others will never use ssh) have already done usual hardening on the host side (like pf, sshguard etc). my major components are: dovecot, exim, apache22, proftpd, perl5.14. Looking for an checklist, what I shouldn't forget. My plan: openssl self-signed certificates for exim, dovecot and proftpd (wildcard keys) openssl self-signed certificate for apache (later will go for "trusted-signed" key) My questions are: is is an "good practice" having one pair of wildcard SSL-certificates for many programs? (exim, dovecot, proftpd) - or should I generate one key for each service? should I add all 4 persons as standard (unix) users, or I should go with virtual users? Asking because: have only small count of users, and it is more simple to configure everything (exim, dovecot) for local users ($HOME/Maildir), plus ability to set $HOME/.forward/vacation and etc. is here some (special) things what I should consider? (e.g. maybe, in the future we want setup our own webmail - will make this any difference?) any other recommendation? Thank you, hoping that this question fit into the http://serverfault.com/faq under the: Server and Business Workstation operating systems, hardware, software Operations, maintenance, and monitoring Looking for an checklist, but please explain why you're recommending it. See Good Subjective, Bad Subjective. related: What's your suggested mail server configuration for a FreeBSD server?

    Read the article

  • Which isn't working on linode servers (Ubuntu 10.04)?

    - by chrisjlee
    Currently trying to configure a linode server running on ubuntu 10.04. I utilized a stackscript (Default drupal profile) which seemed to run successfully. The log indicate so as well. Then ssh'd into the server (as root) to try to configure php. When i run a which php, which php5 they both return nothing. A which python returns something though. I know where the default path to php but i usually just like to use it as confirmation that php exists. Do i have to modify some configurations to enable which to work? Also tab completion doesn't seem to work for when i apt-get install? Update: Thanks for the suggestions guys. I've ran a couple commands and no luck either: [ root@ ~ ] $ dpkg -l |grep php [ root@ ~ ] $ apt-get install php5-cli Reading package lists... Done Building dependency tree Reading state information... Done Package php5-cli is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package php5-cli has no installation candidate Then i tried installing php and php cli: [ root@ ~ ] $ sudo apt-get install php5 php5-cli sudo: unable to resolve host xxxxxxx Reading package lists... Done Building dependency tree Reading state information... Done Package php5 is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package php5 has no installation candidate

    Read the article

  • Automated Linux VMs on Hyper-V 2012

    - by Mick
    I have a requirement to create a ton of linux VMs for our customers (we run managed infrastructure) on Hyper-V 2012 in the coming months and I have an issue with automating it. Here is how I need it to work: User accesses their web page and creates a VM. VM is created with a unique IP and name User logs in over SSH I know Hyper-V quite well and can work with powershell and am a C# programmer so the development side of things is taken care of. I also know enough about Linux to be at least competent: I have used it on and off for a number of years but not done anything Enterprise-level with it. All this can be done easily by manual processes but I need to be able to script or program this to automate it as there could be hundreds of them being created but I don't know how. My first thought is to have a database with random-generated names and IPs already created but I don't know how to get a Linux VM to boot up and grab one from the database... I suppose a Kickstart script would take care of it but I don't know what to do from there. Here is what is bouncing around in my head: Create a std linux build. - Easy to do Someone clicks "Create VM" and I pull a name and IP from the database and write it to a kickstart script. - Easy to do I could then open the template VHDX file and copy in the script and then save it. - Not sure if possible User boots up new VM and the kickstart script gives it the name and IP I assigned it. My problem is that I don't know how to open a VHDX file and insert a kickstart script into it... can't figure it out. I am reaching here and this solution may be miles off... I am more used to creating Windows VMs with scripts and so on which i am more familiar with... any help would be appreciated. Thanks Mick

    Read the article

  • postfix - connection refused from behind NAT

    - by manchine
    When attempting to telnet postfix from a different host in the same LAN through the FQDN (and thus the LAN's public IP), the following error occurs: root@mailer:/var/log# telnet mail.domain.com 25 Trying 1.2.3.4... telnet: Unable to connect to remote host: Connection refused Other services can be reached from the exact same host, however: root@mailer:/var/log# telnet mail.domain.com 22 Trying 1.2.3.4... Connected to mail.domain.com. Escape character is '^]'. SSH-2.0-OpenSSH_6.0p1 Debian-4+deb7u1 To make matters more intriguing, Postfix can be accessed from outside the LAN: nunos-mbp:mailog nzimas$ telnet mail.domain.com 25 Trying 1.2.3.4... Connected to mail.domain.com. Escape character is '^]'. 220 mail.domain.com ESMTP Postfix (Ubuntu) To sum thing up: a) Postfix (running on 10.10.10.4 / mail.domiain.com) refuses connection from a host in the same LAN (10.10.10.2), but only when queried through the FQDN (mail.domain.com) b) mail.domain.com accepts connections to other services (but Postfix) from 10.10.10.2 c) mail.domain.com accepts connections to all services, including Postfix, from the outside world If it were a firewall issue, then I believe it would not be possible to connect to any service from 10.10.10.2 through the FQSN / public IP. It ought to be some missing parameter in Postfix, although I haven't found any clear pointers so far.

    Read the article

  • Replace Linux Boot-Drive | ext3 to btrfs

    - by bardiir
    I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

    Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >