Search Results

Search found 5436 results on 218 pages for 'transfer rate'.

Page 164/218 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

  • How to restrict zone transfers to specific authorized servers only

    - by JonoB
    I recently failed a PCI compliance scan because of the following: This DNS server allows unrestricted zone transfers. Attackers may be able to use this information to gain knowledge on the structure of your networks to aid in device discovery prior to an actual attack. And the suggested solution is as follows: Reconfigure this DNS server to restrict zone transfers to specific authorized servers only. I am running a dedicated Linux Centos server. My understanding is that I have to edit the /etc/named.conf file, which I have done and the the relevant part is as follows: options { acl "trusted" { 127.0.0.1; xxx.xxx.xxx.001; //this is one of the server's ip's xxx.xxx.xxx.002; //this is another server's ip }; allow-recursion { trusted; }; allow-notify { trusted; }; allow-transfer { trusted; }; }; I then restarted the named service /etc/rc.d/init.d/named restart and requested a re-scan, which failed again for the same reason. Am I missing something obvious here?

    Read the article

  • What do "Unknown SSAP" and "Unknown DSAP" mean in tcpdump?

    - by lacker
    While trying to fix a problem with intermittently losing internet connection on a machine with a wireless connection to a router, I ran tcpdump and noticed packets with "Unknown SSAP" and "Unknown DSAP" errors coming at a rate of a few per second. 20:27:21.703178 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xe2 Information, send seq 0, rcv seq 16, Flags [Response], length 171 20:27:21.724726 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xe2 Information, send seq 0, rcv seq 16, Flags [Response], length 104 20:27:21.746449 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xe4 Information, send seq 0, rcv seq 16, Flags [Response], length 88 20:27:21.970963 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xe8 Information, send seq 0, rcv seq 16, Flags [Response], length 76 20:27:22.016565 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xea Information, send seq 0, rcv seq 16, Flags [Response], length 88 20:27:22.038471 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xea Information, send seq 0, rcv seq 16, Flags [Response], length 171 What does the "Unknown SSAP" and "Unknown DSAP" mean, and does it indicate a problem?

    Read the article

  • virtualbox snapshot size

    - by intuited
    I've started using Windows 7 under VirtualBox on an Ubuntu 10.10 host. I took about 6 snapshots over the course of setting up the VM from the Windows restore image that came with the computer. My installations were more or less limited to windows updates, antivirus, and the VB Guest Additions. I uninstalled much more than I installed. The VM was running for about 24 hours total. The snapshots increased in size at a worrisome rate, even when the machine was idle: the snapshot .vdi file for the period between 11:22 PM and 9:02 AM is 6 gigs in size; during that time very little happened. The other .vdi files are between 0.5 and 3 GB, most between 1 and 2 GB. The corresponding .sav files are between 0.5 and 1 GB. The Internet connection where I was doing this is limited to 30KB/s download, which, constantly saturated, works out to less than 3 GB per 24 hour period. Is this normal? Is there something that can be done to make snapshots more practical? update On starting up the VM again, I've noticed that mscorsvw is using significant processing time. Apparently this process [precompiles .NET assemblies]. This may have been going on during the period when I was taking snapshots, which might explain some of the snapshot size increase. I would be somewhat surprised to learn that this could be responsible for over 10 GB of additional disk usage, or that it would run for roughly 24 hours. Is this possible?

    Read the article

  • Why does my Internet slow to a crawl unless I reboot my router every few days?

    - by Lord Torgamus
    A few weeks ago, I noticed that my Internet connection had slowed down to a crawl. I waited a few days hoping it would go away on its own, but it didn't get better. So I asked this question about how to make it faster. The problem went away after I updated to the latest firmware, so I didn't follow up too carefully. But every few days since then, my Internet has slowed down again. Unlike before, all I have to do to fix it is open the router administration page and press the "Reboot" button. Nothing else seems to work, though I'm sure there are options I haven't tried. If it makes a difference, my girlfriend and I both transfer large amounts of data fairly routinely for school (videoconferencing, downloading entire recorded lectures). The router is a Cisco/Linksys 160N V3 that's about a year old. Most of the time, it deals with just two standard Windows 7 laptops. The only thing I came across while searching for answers/dupes was this question, which seems similar superficially, but probably doesn't have the same root issue. Anyways, it's not resolved. What could be causing these slowdowns, and how can I get rid of them?

    Read the article

  • Squirrelmail receiving duplicate emails

    - by Austin
    A client of mine is experiencing issues with his email, it appears that whenever he receives email from a certain domain it comes as duplicates. Not only are they duplicates but the duplicated items have a (+) sign next to them which usually indicates an attachment. Could this be because of a forwarding issue? Here are the headers: Return-Path: <[email protected]> Received: from bigcat.centralmasswebdesign.com (root@localhost) by tarbellconstruction.com (8.13.1/8.13.1) with ESMTP id o4OFnO23003379 for <[email protected]>; Mon, 24 May 2010 11:49:24 -0400 X-ClientAddr: 72.249.26.200 Received: from mf3.spamfiltering.com (mf3.spamfiltering.com [72.249.26.200]) by bigcat.centralmasswebdesign.com (8.13.1/8.13.1) with ESMTP id o4OFnOjF005520 for <[email protected]>; Mon, 24 May 2010 11:49:24 -0400 X-Envelope-From: [email protected] X-Envelope-To: [email protected] Received: From 67-132-16-226.dia.static.qwest.net (67.132.16.226) by mf3.spamfiltering.com (MAILFOUNDRY) id 6lzIAmdLEd+oFQAw for [email protected]; Mon, 24 May 2010 15:49:23 -0000 (GMT) Received: from mail pickup service by WMA2-EXCH1.NELCO-USA.net with Microsoft SMTPSVC; Mon, 24 May 2010 11:49:18 -0400 Content-Transfer-Encoding: 7bit Importance: normal Priority: normal X-MimeOLE: Produced By Microsoft MimeOLE V6.00.3790.4325 Content-Class: urn:content-classes:message MIME-Version: 1.0 Content-Type: multipart/mixed; boundary="----_=_NextPart_001_01CAFB58.AAB268D0" Subject: weekly activity report for week ending May 22, 2010 Date: Mon, 24 May 2010 11:49:16 -0400 Message-ID: <15BCC4D99E8CBF48A2FA37A318CFF5C801209CCC@wma2-exch1.NELCO-USA.net> X-MS-Has-Attach: yes X-MS-TNEF-Correlator: Thread-Topic: weekly activity report for week ending May 22, 2010 thread-index: Acr7WKpdCelRCiocT1eBY2YN5Ma8DA== From: "Mike LeBlanc" <[email protected]> To: "Keith Berube" <[email protected]>, "Ken Tarbell" <[email protected]> X-OriginalArrivalTime: 24 May 2010 15:49:18.0361 (UTC) FILETIME=[AB546890:01CAFB58]

    Read the article

  • Toshiba Satellite U500 - Totally Damaged LCD

    - by ivan
    I accidentally damaged my Toshiba Satellite U500 laptop which resulted in a totally unusable LCD. The LCD panel has some cracks on it, and I can only see black & white spots; the laptop frame became broken/bent to where I can partially see inside the PC; the accident disassembled the CD tray, and bent the keyboard frame (which now has a weird hump). The system is still working though. It responds to my inputs (eg, turning it on/off, typing my password @ Windows Login, etc). What I want to do now is to transfer all of my important data from that laptop to my external drive. But I don't know how since the LCD screen is unreadable. I know I can connect it to an external monitor or a TV (I have a Samsung 1080p TV) but I don't know how. What cable should I purchase to connect the TV? Which ports on the laptop and TV should I connect it to? Do I need press something while/after connecting it? Can I boot my laptop using the TV?

    Read the article

  • How do I export address book from N97

    - by mplungjan
    Hi, I need to copy my numbers from my private Nokia to my office BB. I have not found a way to export my phone numbers from ovi or elsewhere. On Mac iSync stopped working with snow leopard and OVI on windows does not export. I do not mind using a windows suggestion. I lost a description on how to use the ovi backup files in another program. What I have done so far terminal: sudo open -a iSync.app - it launched but iSync said "this device is not supported by iSync" went here http://europe.nokia.com/support/product-support/isync/compatibility-and-download found a plugin (I am sure that was not there a while ago :| ) Checked software version 22.0.110 installed plugin Ran iSync which found and installed my N97 device successfully. synced. It stopped with The connection was lost while talking to the phone. http://discussions.europe.nokia.com/t5/Nseries-and-S60-Smartphones/N97-iSync-Multimedia-Transfer-Modem/m-p/568560 no news since Jan 2010. Tried to download and install http://best-vcard.en.softonic.com/symbian but the installer fails :( I simply do not understand why Nokia is giving us such a hard time. I would not have considered switching from Nokia if Mac had been better supported. It is so frustrating that they just seem not to care losing Nokia fanbois like me - especially since I am this outspoken on the net and what i say on popular forums gets indexed by google fast. I am very close to just go iPhone here. Hope someone has Nokia's ears UPDATE: I Downloaded NbuExplorer from sourceforge. It will extract everything from an OVI backup into VCF, VCS and VMG files. Very useful software and free.

    Read the article

  • How to set up QoS on ADSL router (terracom) for prioritizing browsing

    - by DBZ_A
    I want to configure the ADSL router which connects 10+ machines to the internet. I want to give maximum priority to browsing (ports 80,443) and set low priority for bittorrent etc.(port 42180) I have been experimenting with settings , but with no luck. There are three settings which confuse me, along with my understanding. 802.1 Priority - Related to LAN level, possible values 0-7 , higher numbers means higher priority. 'Mark traffic priority' - clueless about this. IPP/DS - IP Precedence - possible values 0-7 ; 6 & 7 are reserved, so set 5 for highest priority. Or when using DSCP - set 46 for highest priority. Please help me in getting this done... Similer question for another model of router here , but with less number of confusing options :) How to configure QoS on home router Update: from discussion on another thread, QoS can control only upstream traffic (from router to the internet) , while this may in turn affect downstream traffic rate, there is no direct control over data coming into the router.

    Read the article

  • Security and data backup for Ubuntu usb installation

    - by AMS949
    Due to encryption on my corporate laptop I opted to install Ubuntu 9.10 on a flash drive and just use it as my hard drive. I tried the vmware but it crashed my xp a couple of times. Now I have a couple of concerns since I am totally new to Ubuntu and Linux. First, would it be possible for me to transfer my installation to a new usb drive? I now have a 4gb and it may get filled up soon, I don't seem to be able to see my actual files when I browse the usb drive. I also tried copying all files from this usb to another and boot from it but that failed. Second, whenever the system boots up I am never prompted for a password, it is always the username ubuntu. Which I guess means if I lose my usb drive my data is open wide. Is there a way to secure it or to use users and groups as on a regular hard drive installation? As a background, I created this by going into a working Ubuntu installation, System - Administration - USB Starter Disk Creator (was that the right way to start with?) Thanks!

    Read the article

  • Dropbox failing to update?

    - by Mick
    I have two PC's at home. One XP the other Windows 7-64bit. I have a word document that I edit on either PC - to enable this I have the file stored in a Dropbox folder. This usually works fine - but sometimes I find that the file does not get updated on my windows7 PC. I.e. I edit the file on my Windows XP machine, then go to my Windows 7 PC and see that there is a previous, old, datestamp on the file and sure enough if I open up the file to have a look, I see that the latest edits are not included. If I right-click on the file and select "Browse on Dropbox website" I see that the latest file is correctly there. Surely there must be some option to say please update this file - but can find no such thing. Has something gone wrong? I should point out that my wireless internet connection is a little intermittent - could this have caused some glitch? By the way I do not leave the old file open in word on my Windows-7 PC as I can well imagine that would cause trouble. Also I should mention that the icon on the document has the little green tick on it showing that Dropbox is not in the process of doing a transfer. Also the Dropbox icon in my system tray also has the green tick - so Dropbox is not busy transferring some other file(s). If I hover the mouse over the Dropbox icon I get the tooltip "All files up to date".

    Read the article

  • Embedding a WMV file on the web via URL in a Powerpoint presentation

    - by Dave
    I've got a situation where I want to distribute a Powerpoint presentation to several people. I want to be able to embed several large videos in this presentation by linking to a URL, for the following specific reasons: the videos are highly confidential, and I would like to be able to delete them at some later date, but still allow them to see it in the presentation while it is online. I want to send the presentation via email (so it should be small), and put the links on a server with a faster upload speed Maybe I'd like to change the video at some point without changing the presentation One option that addresses #1 is to hook up a webcam and allow them to see video stream from the office, but our upload rate is too slow for this to be a viable option. I've tried embedding a video and giving Powerpoint the URL. It seems to work initially, because the first frame appears in my slideshow. However, when I play the slideshow, nothing happens. I looked at the network traffic on my computer, and nothing was getting downloaded from the remote server. Any suggestions on how to make this work, or how to at least satisfy the criteria listed above would be great!

    Read the article

  • Replacing local home server with VPS: Suggestions?

    - by CamronBute
    So right now, I'm running an old box with a 2TB HDD in it. I use this as a file server for the home network, as well as a box for downloading large files which are synced via Dropbox. Lots of other tinkering things, too. Basically, I'm sick of paying extra for the power and having to worry about drive failures and whatnot. I'd rather get a remote server, let someone else manage it and provide access from the Internet. So, I've been looking for a Windows VPS that would give me access to install things and tinker, and I'm having a problem finding a host that offers more than 100GB of hard drive space. If they do offer a package with 100GB of storage, everything else is waaayyyy more than what I actually need. The idea is to create a permanent VPN connection from the cloud server to my home network to provide a transparent solution so I'm not having to go to lengths to transfer files or whatnot. I think a VPS solution will allow me to do this. I would like 1TB of storage space, minimum 100Mbps Internet connection, minimum 250GB bandwidth, admin access. Anyone have anything? Or am I being unreasonable? If I am, why?

    Read the article

  • Strange ASP.NET Queue Performance Counters Behavior?

    - by LemurTech
    We have an ASP.NET 2.0 site running in classic mode. I am seeing very strange behavior in the performance counter values. Perhaps these are bugs (I've been all over Google trying to verify this, without much luck), or perhaps it is just my inexperience with monitoring these things. This PerfMon graph (http://imgur.com/Jv5io5J) represents a load test where I add up to 350 virtual users to the site, at a rate of about 1/sec, performing relatively simple page browsing. At the end of the test, I gradually taper off the number of users. This is a 4 CPU server. Machine.config settings for are at the defaults. The solid blue line is ASP.NET Apps v2.x\Requests Executing for the application in question. The profile makes perfect sense, with a quick ramp-up to 32 executing requests (minWorkerThreads x 4CPUs), followed by a slower ramp-up to 48 ((maxWorkerThreads - minWorkerThreads) x 4CPUs). The solid yellow line is ASP.NET v2.x\Requests Queued. Again, this makes sense: after the initial 32 request threads are activated, the queue begins to build as new thread initialization can't keep pace with incoming requests. But as executing requests reaches its highest possible value of 48, the counter for ASP.NET Apps v2.x\Requests Queued (green solid line) suddenly springs to life and maintains step with the yellow counter. As far as I can tell, and with no other apps running on the server, these two counters should have had the same values from the start. One other odd thing: The counter for ASP.NET v2.x\Request Wait Time (dotted yellow line) also does not spring to life until executing requests reaches 48. Shouldn't I be seeing values here from the moment ASP.NET v2.x\Requests Queued begins to build? And likewise, why would ASP.NET Apps v2.x\Request Execution Time (dotted blue) increase significantly only after that peak of 48 is reached? Shouldn't it ramp-up gradually along with queued requests?

    Read the article

  • Apache process consuming all memory on the server

    - by jemmille
    I have an apache process that suddenly appears on a particular server. When it shows up it starts consuming memory at a very rapid rate, then moves on to all the swap. In all it consumes about 11GB (including swap) of memory and the server eventually becomes unresponsive. The load on the server is under 1 at all other times. The process runs as nobody and I am having a hard time tracking down the source. If i run an strace on the process and all it did was continuously dump out mprotect over and over again If i run lsof -p <pid>, I get this, but only sometimes: httpd 19229 nobody 152u IPv4 175050 crawl-66-249-67-216.googlebot.com:62336 (CLOSE_WAIT) httpd 19229 nobody 153u IPv4 179104 crawl-66-249-71-167.googlebot.com:58012 (ESTABLISHED) As long as I catch it, I can kill the process and the server almost immediately stabilizes. I have on site on the server that is getting a few thousand hits a a day that I think might be the source, but I still can't find the exact reason. Also, this is a cPanel server and I have upcp'd the server, rebuilt apache with easy apache, and rebuilt httpd.conf. It is not spawing any related processes, meaning I can find any php, mysql, cgi, etc. processes that relate to this process. It's just a loner process that balloons fast and consumes ever last MB of memory. This is on a XenServer 5.6 based VM. No other servers in the cluster are having this issue.

    Read the article

  • Improving abysmal 802.11n wireless network

    - by concept
    I am in desperate need of help to improve the abysmal performance of my 802.11n wireless network. At best I get 30Mbs (this is an internet download) from a technology that boasts 300Mbs, even worse is the LAN where to date best i have ever gotten is 1Mbs. It is literally quicker to copy the file to a USB and walk it to the other computer. Infrastructure is this AP 802.11n only broadcasting at both 2.4GHz and 5GHz Mac with 802.11a/b/g/n card is connected to the AP via 5GHz Linux with 802.11a/b/g/n card is connected to AP via 2.4GHz I have conducted the following tests (results at end of post) Internet based speed test wired and wireless LAN file copy wired and wireless I have read: http://nutsaboutnets.com/troubleshooting-wi-fi-problems/ http://www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-- speed http colon //www.wi-fiplanet dot com/tutorials/7-tips-to-increase-wi-fi-performance.html Slow file transfer on network between two 802.11n laptops (connected directly together via access point) Wireless Network Performance Issues Slower than expected 802.11n wireless network speeds I have made the following optimizations AP broadcasts only 802.11n on both 2.4GHz and 5GHz frequencies 2.4GHz is on a channel with least interference (live in an apartment with lots of APs), this did make a 10Mb/sec improvement Our AP is the only one transmitting on the 5GHz freq. Security: WPA Personal WPA2 AES encryption Bandwidth: 20MHz / 40MHz (i assume this to be channel bonding) I have tried the following with 0 improvement Dropped the Fragment Threshold to 512 Dropped the Request To Send (RTS) Threshold to 512 and 1 Even thought of buying a frequency spectrum analyzer, until i saw the cost of them!!! Speed test results Linux Wired: DOWNLOAD 128.40Mb/s UPLOAD 10.62Mb/s www dot speedtest dot net/my-result/2948381853 Mac Wired: DOWNLOAD 118.02Mb/s UPLOAD 10.56Mb/s www dot speedtest dot net/my-result/2948384406 Linux Wireless: DOWNLOAD 23.99Mb/s UPLOAD 10.31Mb/s www.speedtest dot net/my-result/2948394990 Mac Wireless: DOWNLOAD 22.55Mb/s UPLOAD 10.36Mb/s www.speedtest dot net/my-result/2948396489 LAN NFS 53,345,087 bytes (51Mb) file Linux Mac NFS Wired: 65.6959 Mb/sec Linux Mac NFS Wireless: .9443 Mb/sec All help is appreciated, even testing methods will be accepted.

    Read the article

  • How to solve SocketException: Permission denied: connect

    - by luxinxian
    I recently encountered a problem that is giving me a headache and I need help ... The System consists of two subsystems, called A and B, each running on a standalone Tomcat instance and currently running on the same machine. A invokes B's service via Spring httpInvoker (i.e. over HTTP). B system also invokes the other system's services via HTTP. Symptoms: the system starts to run and appears to work normally for around 10-15 days; the system will run for a period of time after an exception: org.springframework.remoting.RemoteAccessException: Could not access HTTP invoker remote service at [http://xxx.xxx.xxx.xxx/remoting/call]; The nested exception is java. net.SocketException: **Permission denied: connect** when the exception occurs, the system continues. This happens always, not only occasionally. (It looks like some resources are exhausted, but CPU rate < 5%, memory < 15%, network < 5%). when the system call between A and B fails, the B system call over HTTP to an external service also failed, with the same exception. Restarting both Tomcat services makes the whole system work properly. So repeatedly following steps 1 - 5, I have not found the root reason. Environment: windows 2008 R2 tomcat7.0.42 x86_64 oralce-jdk-1.7.0_40 Any ideas?

    Read the article

  • Reducing IO caused by nginx

    - by glumbo
    I have a lot of free RAM but my IO is always 100 %util or very close. What ways can I reduce IO by using more RAM? My iotop shows nginx worker processes with the highest io rate. This is a file server serving files ranging from 1mb to 2gb. Here is my nginx.conf #user nobody; worker_processes 32; worker_rlimit_nofile 10240; worker_rlimit_sigpending 32768; error_log logs/error.log crit; #pid logs/nginx.pid; events { worker_connections 51200; } http { include mime.types; default_type application/octet-stream; access_log off; limit_conn_log_level info; log_format xfs '$arg_id|$arg_usr|$remote_addr|$body_bytes_sent|$status'; sendfile off; tcp_nopush off; tcp_nodelay on; directio 4m; output_buffers 3 512k; reset_timedout_connection on; open_file_cache max=5000 inactive=20s; open_file_cache_valid 30s; open_file_cache_min_uses 2; open_file_cache_errors on; client_body_buffer_size 32k; server_tokens off; autoindex off; keepalive_timeout 0; #keepalive_timeout 65;

    Read the article

  • Cisco ASA5505 won't sync with NTP

    - by Martijn Heemels
    Today I noticed that the clock my Cisco ASA 5505 firewall was running about 15 minutes late, which surprised me since I've set up the NTP client. My two NTP servers 10.10.0.1 and 10.10.0.2 are virtualized Windows Server 2008 R2 domain controllers, and both have the correct time. As shown below, the ASA knows about the two servers, can ping them and seems to poll them periodically, so I suppose it can reach them both. The ASA claims its time source is NTP, however the clock is unsynchronized. Neither host is marked as synced. Result of the command: "ping 10.10.0.1" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.10.0.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Result of the command: "sh ntp ass" address ref clock st when poll reach delay offset disp ~10.10.0.1 .LOCL. 1 78 1024 377 0.5 643.69 17.0 ~10.10.0.2 10.10.0.1 2 190 1024 377 0.9 655.91 58.4 * master (synced), # master (unsynced), + selected, - candidate, ~ configured Result of the command: "sh ntp stat" Clock is unsynchronized, stratum 16, no reference clock nominal freq is 99.9984 Hz, actual freq is 99.9984 Hz, precision is 2**6 reference time is 00000000.00000000 (07:28:16.000 CEST Thu Feb 7 2036) clock offset is 0.0000 msec, root delay is 0.00 msec root dispersion is 0.00 msec, peer dispersion is 0.00 msec Result of the command: "sh clock detail" 10:33:23.769 CEDT Tue Jun 26 2012 Time source is NTP UTC time is: 08:33:23 UTC Tue Jun 26 2012 Summer time starts 02:00:00 CEST Sun Mar 25 2012 Summer time ends 03:00:00 CEDT Sun Oct 28 2012 I've tried the basic steps of manually setting the time and removing and adding the timeservers, to no avail. My ASA's ntp config is simply: ntp server 10.10.0.1 ntp server 10.10.0.2 Do I need to enable authentication to use a Windows NTP server? Any thoughts?

    Read the article

  • Copying large files from USB devices to the internal hard drive fails on Mac OS

    - by John M. P. Knox
    I have a second-generation 13" MacBook Air running Mac OS X 10.6.6 with a 2.13 GHz processor, 4 GB of RAM, and a 256 GB SSD hard disk. I often get failures when I attempt to copy a large file or large collection of files from an external USB drive (typically a "Firewire" generation Drobo) to the internal drive. The failure behaves almost exactly as if I had pulled the USB cable from the computer in mid-transfer. I get a warning that I have removed the hard disk improperly. After this event, the drive no longer appears mounted in the finder, and I have to unplug and reinsert the USB cable to mount the drive again. I have also seen a similar problem when using Aperture 3 to import a large number of photos and videos from a USB Compact Flash card reader. The import will fail and I will have to unplug the Card Reader and import the missing items. Oddly, reversing the direction of the copy seems pretty reliable. I've never had a problem copying a large file to a USB device, meaning that I have quite a few large files which are stranded on my Drobo. Model Identifier: MacBookAir3,2 Boot ROM Version: MBA31.0061.B01 I have seen a similar issue reported on Apple's website: http://discussions.apple.com/thread.jspa?threadID=2648590&tstart=0 The only suggested resolutions there seems to be switching to another form of connectivity (e.g. firewire, which does not exist on MacBook Air), or downgrading to Mac OS 10.6.4, or reverting the USB kernel extensions to the 10.6.4 versions: http://discussions.apple.com/message.jspa?messageID=12566073#12582956 I'm not too keen on the idea of downgrading kernel extensions. Does anyone know of a hardware revision without this issue that I can trade up to? Are there any other potential solutions out there?

    Read the article

  • SSH client and Command Prompt replacements Windows look-and-feel

    - by Oddthinking
    The Problem I've worked exclusively in Windows. I can handle that. I've worked exclusively in DOS (a long time ago!). I can handle that. I've worked exclusively in Unix. I can handle that. Right now, I am developing a command-line (python) application on a Windows machine, testing it in a DOS box (i.e. Windows' Command prompt), and then deploying it to Linux, and running it with PuTTY. I cannot handle that. My productivity drops dramatically when CTRL-C cuts in one window (Windows) and kills the process in another (DOS, Linux). My productivity drops dramatically when Enter copies the selection in one window (DOS), and deletes the selection in another (Windows), and runs the current half-edited command in the third (PuTTY). My productivity drops dramatically when I cannot hit Undo, Home or End. The Solution I am Seeking An SSH/Bash command-line client that runs on Windows and, to the extent possible, uses all the standard Windows shortcuts (Cut, Copy, Paste, Undo, Home, End, Insert, Shift-Arrows, etc.) work on a bash command line. Bonus points if it puts the cursor between letters, rather than on them. Plus, an equivalent DOS command-line drop-in that runs on Windows, and provides the same interface. I appreciate there may need to be special buttons to actually transfer CTRL codes (like CTRL-C) through in the cases I need them. I suspect the SSH client will need to be specific to a shell (so it knows when it is at the command prompt, and when it is inside a running app.) I know there are many SSH clients, but I am looking for advice for a particular need. PuTTY feels like an escape route for Unix programmers stuck on Windows. I am the opposite. Can anyone recommend one (or maybe a combination of an SSH client and an Command-Line replacement)?

    Read the article

  • Servers in DMZ will not communicate with each other

    - by Tukaro
    (Full disclosure: I rate barely above "noob" when it comes to networking.) My workplace recent got a new web server. Since we're nearing the end of an overhaul of our website, we're doing a slooooow migration between the old web server and the new one. The old webserver (we'll call it SERVOLD) is Windows Server 2008 with IIS 7. It does not have SQL Server installed. The new server (SERVNEW) is Windows Server 2008 R2, IIS 7.5, with the same version of SQL Server installed. Both are located in the DMZ for our network, and both have their own outward-facing IP address (.3 and .4, respectively). Each server can communicate fine with computers within the domain (not in the DMZ), and those same computers have no trouble communicating with either server. Both servers are also accessible from the internet just fine. However, no matter what, these two servers just refuse to recognize each other. They have the same Workgroup name listed (WORKGROUP), and I thought that would be enough for them to recognize each other. What needs to happen such that I can get these two servers to communicate with each other? We want to do a gradual roll-over to the new website (new one uses ASP.NET, old one uses CFMX), so being able to use one database between both servers is a necessity. Thanks!

    Read the article

  • Postfix Problem (helo/hostname mismatch)!

    - by CuSS
    Hi all, I have a server, and it is running a error for one email only (all other mails in that domain are working). How can i fix it? (The error is above:) May 17 11:43:56 webserver postfix/policyd-weight[5596]: weighted check: IN_DYN_PBL_SPAMHAUS=3.25 NOT_IN_SBL_XBL_SPAMHAUS=-1.5 NOT_IN_SPAMCOP=-1.5 NOT_IN_BL_NJABL=-1.5 DSBL_ORG=ERR(0) CL_IP_NE_HELO=4.75 RESOLVED_IP_IS_NOT_HELO=1.5 HELO_NUMERIC=10.625 (check from: .eticagest. - helo: .[10.0.0.17]. - helo-domain: .17].) FROM_NOT_FAILED_HELO(DOMAIN)=6.25; <client=188.80.139.211> <helo=[10.0.0.17]> <[email protected]> <[email protected]>; rate: 21.875 May 17 11:43:56 webserver postfix/policyd-weight[5596]: decided action=550 Mail appeared to be SPAM or forged. Ask your Mail/DNS-Administrator to correct HELO and DNS MX settings or to get removed from DNSBLs; MTA helo: [10.0.0.17], MTA hostname: bl15-139-211.dsl.telepac.pt[188.80.139.211] (helo/hostname mismatch); <client=188.80.139.211> <helo=[10.0.0.17]> <[email protected]> <[email protected]>; delay: 6s

    Read the article

  • Why are FMS logs filled with 'play' event status code 408 for a failed webcast?

    - by Stu Thompson
    Recently we had a live webcast event go horribly wrong. I'm doing the technical post-mortem, with limited information. We know that the hardware encoder (a Digital Rapid Touch Stream Web HDI) was unable to send upstream at a sustained reliable high rate. What we don't know is if the encoder's connection was problematic (Zürich), or that of the streaming server (in Frankfurt). Unfortunately, I've got three different vendors all blaming each other (the CDN who runs the server, the on-site ISP and the on-site encoding team.) In the FMS log files I see a couple of interesting things: Zillions of Status Code 408 on play event entries for clients. Adobe's documentation stats that this "Stream stopped because client disconnected". ("Zillions" would be a ratio of 10 events for every individual IP address.) Several unpublish / (re)publish events per hour for the encoder I'd like to know if all those 408s could tell me with authority that the FMS server was starved for bandwidth, or that the encoding signal was starved (and hence the server was disconnecting clients.) Any clues?

    Read the article

  • iOrgSoft Video Converter for Mac

    - by terryhao
    [url=http://www.iorgsoft.com/Video-Converter-for-Mac/]video converter for mac[/url] IOrgSoft[url=http://www.iorgsoft.com/Video-Converter-for-Mac/]video converter for mac[/url] is an excellent video converting and editing software for Macintosh users. A built-in powerful video player, trimming, splitter/joiner/merger tools give you everything you need to manage your videos on mac. This mac converter supports many video formats like AVI, MP4, WMV, MPEG-1,2, YouTube(FLV), Limewire, Realplayer(RM,RMVB), Quicktime(MOV), MKV, MOD, TOD, ASF, 3GP, 3G2, AVCHD/M2TS/MTS/TS/TRP/TS, MXF, etc. Video Converter for Mac features a very clean user interface which makes this task a breeze. You can trim/clip any segments and optionally merge/join and sort them to create your personal movie, crop frame size to remove any unwanted area in the frame just like a pair of smart scissors and set the output video parameters such as video resolution, video frame rate, audio codec, video codec and video quality. Converted videos can be imported into imovie/itunes/FCE/FCP/QuickTime Pro or played on iPad, iPod touch, iPod classic, iPod nano, iPhone, iPhone 3GS, Apple TV, PSP, PS3, Creative Zen, iRiver PMP, Archos, mobile phones and other MP4/MP3 players. Video Converter for Mac makes video conversion easy. Free download now and have a try for yourself! [url=http://www.iorgsoft.com/Video-Editor-for-Mac/]Video Editor for Mac[/url] [url=http://www.iorgsoft.com/Mod-Converter/]mod converter[/url] [url=http://www.iorgsoft.com/Mod-Converter-for-Mac/]mod converter for mac[/url]

    Read the article

  • KVM guest VLAN aware problems

    - by baraka
    Hi, We are using Centos 5.5. as KVM host. It has two nics. One for management and the other one for services. As we have services in multiple vlans this nic is configured as a 802.1Q trunk. Any VM must be able to have access to any vlan, so host trunk interface is bridged to its tap interface and vlan is configured inside VM. Everything works fine while there is not heavy traffic. I can not find any log on guest or host, but, after some certain sustained big file transfer (about 6Gb) bridging stop working. Other guest on the same host continue working without problems. tcpdump on bridge interface is Ok, but on guest tap inferface I can see only outgoing traffic. Restarting bridge or rejoining tap interface doesn't provide any clue. Rebooting guest turns on bridge again. Bridge configuration is minimal: just addbr and addif (no stp). Any idea welcome!

    Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >