Search Results

Search found 6317 results on 253 pages for 'persistent storage'.

Page 167/253 | < Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >

  • SAS instead of SATA 2 for my hard drives?

    - by jasondavis
    I am building a new system soon, I will have multiple 1-2tb hard drives for storage in it. I only have experience uasing the sataII drives but I saw somewhere that I should be using something like SAS? I read that if I were going to have 20 drives that I could use 4 SAS cables vs 20 SATA cables. Can someone help me understand this better? If it were only 4 cables then how would 20 drives hook up? Also can a regualr sata2 drive hook up to that?

    Read the article

  • FreeNAS - how to "Exclude from file" in Rsyncd (GUI)

    - by user179181
    I am trying to set rsync tasks to Pull user profiles from 11 Windows machines running DeltaCopy Server and then configure ZFS periodic snapshot tasks for a backup solution. So far this has been working fine, although i would like to exclude certain file types like .DAT or NTUSER.DAT. My Exclusion file resides on the local ZFS Dataset (Receiving side) and is as follows: Temp Temporary Internet Files NTUSER.DAT NTUSER.DAT.LOG *.dat *.tmp *.DAT.log *.ost *.pst The command i typed under Auxiliary Parameters (Rsyncd Global Conf under services)is as follows: exclude from = /mnt/Storage/User_Profiles/exclude.txt Ive tried deleting the .DAT files from the receiving end and just as i start to get excited i click refresh and there they are again

    Read the article

  • How do you passthrough native SATA drives to a guest on ESXi?

    - by John
    I have ESXi 4.0 running on an Intel DX58S0 Mothboardboard with an Intel Core i7 930 processor. VT-d is also enabled. I have three drives in the system, drive 0 is used for ESXi. Drive 1 and 2 contain data from an older machine and show up under the "Storage Adapters" section in configuration. I would like to allow a guest machine to access the data on these drives (as nativly as possible). I have enabled passthrough of the motherboard's built in SATA controller (Intel/Marvell 88SE6121 ). This controller shows up in my guest OS, but the guest shows no drives aside from the normal virtual drive. I have tried a Linux guest and Windows7. I have also configured the host machine to try IDE/RAID/ACHI modes for the SATA controller. Any ideas how I can configure one of my guests to get at the raw data on these drives?

    Read the article

  • Mysterious Windows 7 slowdown problem

    - by cletus
    I have a fairly beefy machine: Intel Q9450 8GB DDR2800 (4x2) Intel X25-M G2 80GB SSD Several other hard drives Windows 7 Ultimate 64 In the last month I've gotten a mysterious slowdown problem. When I start my IDE (IntelliJ IDEA) it usually takes about 20 seconds on the SSD. If my machine has been on for a day or two (as far as I can tell this is the only pattern) and I try to start the IDE, it brings my machine to a halt. CPU usage goes up to 25% per core (so it's basically 100% usage) and it takes up to 5 minutes to start. Other things I've noticed: iTunes will start to skip and stutter (my music is running off a second hard drive). The only persistent things I'm running are: AVG Anti-Virus Spybot (the slowdown predates this) Hamachi and Murmur (again the slowdown predates this) Apple Airport Base Agent HP OfficeJet 8500 driver/manager The browser I use is Chrome. I can't think why that'd be relevant but it's always on so I thought I'd mention it. When this happens I can't see a reason for it in the process list. No CPU hogs. No spikes in IO activity that I can see. Basically I'm at a loss to explain it and need to reboot, at which point everything returns to normal (for awhile). FWIW the Intel SSD is about 75-80% full. I know being too full can really degrade performance. I don't believe that's the issue here. Does anyone have any ideas on what I can do to fix this or at least help find what's going wrong? This same machine (sans SSD) could run Win XP and stay up fine for a month or two.

    Read the article

  • Is it possible to create a delta VM?

    - by iTayb
    I have a VM of approx. 18GB. Sometimes I need temporally clones of it, so I clone it. The problems are: * It takes a while until it's done. * Sometimes I happen to need dozen of clones and I'm running out of storage. I wonder if there's a way to create a VM that saves only the delta (difference) since the delployment out of the source machine. That way each new VM's filesize should be 100MB at most, and creating it will be much faster. I've heard that VMWare View is using this concept. Is such a thing possible for ESXi as well? I'm using ESXi 4.1 with VSphere 4.1. Thanks!

    Read the article

  • Too much free space on FreeNAS - ZFS

    - by Guillaume
    I have a FreeNAS server with 3 x 2 To disks in raidz1. I would expect to have about 4 To of space available. When I run zpool list I get: [root@freenas] ~# zpool list NAME SIZE USED AVAIL CAP HEALTH ALTROOT main_volume 5.44T 3.95T 1.49T 72% ONLINE /mnt I was expecting a size of 4 To. Also, used space as reported by zpool list does not match what's reported by du: [root@freenas] ~# du -sh /mnt/main_volume/ 2.6T /mnt/main_volume/ There are quite a few things that I dont yet completely understand about ZFS. But at the moment I am mostly worried that I misconfigured my system and that I dont have any storage redundancy. How can I make sure I did not do an horrible mistake ... For the sake of completeness, here is the output of zpool status: [root@freenas] ~# zpool status pool: main_volume state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM main_volume ONLINE 0 0 0 raidz1 ONLINE 0 0 0 gptid/d8584e45-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 gptid/d8f7df30-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 gptid/d9877cc3-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 errors: No known data errors

    Read the article

  • How to Mirror or Clone a Spanned Volume in Windows 2008

    - by Matt
    I have a spanned volume (3x6+ TB disks spanned to one 20+ TB volume) that I need to mirror or clone to a new 20+ TB (unspanned) volume. Once mirrored or cloned I'm going to destroy the original volume and reuse the storage elsewhere. Windows 2008 will not allow me to mirror it because the original is a spanned volume. I cannot simply copy the data, because there are sparse files on the volume. So the OS thinks there is 150+ TB used on the disk when there really is only around 18TB used physically. When I try to use the copy command it won't run because it thinks the destination volume needs to be 150+ TB to hold it all. A conundrum, but I figure someone here has the answer. Thanks, Matt

    Read the article

  • Distribute terrabyte files to the public from web server

    - by MarkJ
    Hi We need to set up a website which makes two or three large files publicly available - the files will be 1 or 2 terrabytes each. Although they will be public, in practise I expect only a relatively small number of scientists will want to download them. What is the best way to allow this? I've had a quick talk to a web-hosting provider (rackspace) and they suggested a hybrid solution. An entry-level managed server (we predict fairly low traffic for the website, but we do need to install some custom CGI software). Some cloud storage which hooks into Limelight Networks. This would host the large files, for download by FTP. It sounded OK to me but I know relatively little about server administration. Does it make sense? Thanks in advance, Mark

    Read the article

  • Mounting root failed. Dropping into basic maintenance shell

    - by vmsystem
    Hi, I have purchased AMD Phenom X4 955 3.2GHZ processor with supporting gigabyte GA-MA785GM-US2H mother board / 6GB DDR2 RAM / 500GB SATA drive for learning Vmware ESX 3.5 product. In the above configuration, I have installed windows xp 64 bit operating systems and continue to installed vmware workstation 6.5. From the VM workstation, I can able to install ESX3.5 update2, but I unable to start properly, please refer the below mention error. “Mounting root failed. Dropping into basic maintenance shell. To collect logs for VMware, connect a USB storage device and run 'bin/vm-support '. Machine will be rebooted when you exit from this shell.” The same was tested in the windows 2003 Enterprise Edition server / windows 7 32bit / windows 7 64bit also, Please help me to resolve the issue.

    Read the article

  • Best way to convert from IMAP to POP3?

    - by Brad
    At work, I connect to a corporate Exchange server via IMAP and Thunderbird 3. Over the course of a year or so, I've created quite a few folders on the server and have a lot of mail stored there. I'm hitting the storage limit of my mail account and want to convert to pulling mail down to my local box (running Linux) via POP3. I know that polling mail will only get mail in INBOX, but I'm wondering if there are solutions out there that could be used to pull mail from the other folders as well, or am I doomed to moving mail into the inbox manually and polling over and over again?

    Read the article

  • HDD situation - what would be best - data and backup

    - by Sam Johnson
    I just installed W8 on an Intel 330 180 GB SSD. I have 3 1TB HDDs. 1 HDD will be external for backup. 2 HDDs are then available for my PC. I do not need 2 TB of storage, so I thought I'd set these up to be exact clones of one another, so that if one dies I have a backup in the computer to go along with my external. Is this a good set up? How best would this be accomplished? I've heard people suggest RAID but I've never done RAID, have no idea what it is, and have no idea how to set it up in my BIOS. Thanks in advance

    Read the article

  • Best way to replicate servers

    - by Matthew
    I currently have two servers both with linux software RAID1 configurations. They use heartbeat and DRBD to create a shared DRBD device that hosts a a exported NFS directory. The servers run Ubuntu Server with a LXDE GUI and some IP These servers are going to be placed on fishing vessels to act has redundant storage for IP cameras. My boss wants me to figure out the most efficient way to create these servers. We might be looking at pushing out several systems a week. Each configuration will be almost identical besides IP addressing. What would be the best method to automate the configuration process? We are trying to cut down on labor costs to set these up. Imaging and Proceeding are both on my mind right now

    Read the article

  • jQuery - I'm getting unexpected outputs from a basic math formula.

    - by OllieMcCarthy
    Hi I would like to start by saying I'd greatly appreciate anyones help on this. I have built a small caculator to calculate the amount a consumer can save annually on energy by installing a ground heat pump or solar panels. As far as I can tell the mathematical formulas are correct and my client verified this yesterday when I showed him the code. Two problems. The first is that the calculator is outputting ridiculously large numbers for the first result. The second problem is that the solar result is only working when there are no zeros in the fields. Are there some quirks as to how one would write mathematical formulas in JS or jQuery? Any help greatly appreciated. Here is the link - http://www.olliemccarthy.com/test/johncmurphy/?page_id=249 And here is the code for the entire function - $jq(document).ready(function(){ // Energy Bill Saver // Declare Variables var A = ""; // Input for Oil var B = ""; // Input for Storage Heater var C = ""; // Input for Natural Gas var D = ""; // Input for LPG var E = ""; // Input for Coal var F = ""; // Input for Wood Pellets var G = ""; // Input for Number of Occupants var J = ""; var K = ""; var H = ""; var I = ""; // Declare Constants var a = "0.0816"; // Rate for Oil var b = "0.0963"; // Rate for NightRate var c = "0.0558"; // Rate for Gas var d = "0.1579"; // Rate for LPG var e = "0.121"; // Rate for Coal var f = "0.0828"; // Rate for Pellets var g = "0.02675"; // Rate for Heat Pump var x = "1226.4"; // Splittin up I to avoid error var S1 = ""; // Splitting up the calcuation for I var S2 = ""; // Splitting up the calcuation for I var S3 = ""; // Splitting up the calcuation for I var S4 = ""; // Splitting up the calcuation for I var S5 = ""; // Splitting up the calcuation for I var S6 = ""; // Splitting up the calcuation for I // Calculate H (Ground Sourced Heat Pump) $jq(".es-calculate").click(function(){ $jq(".es-result-wrap").slideDown(300); A = $jq("input.es-oil").val(); B = $jq("input.es-storage").val(); C = $jq("input.es-gas").val(); D = $jq("input.es-lpg").val(); E = $jq("input.es-coal").val(); F = $jq("input.es-pellets").val(); G = $jq("input.es-occupants").val(); J = ( A / a ) + ( B / b ) + ( C / c ) + ( D / d ) + ( E / e ) + ( F / f ) ; H = A + B + C + D + E + F - ( J * g ) ; K = ( G * x ) ; if ( A !== "0" ) { S1 = ( ( ( A / a ) / J ) * K * a ) ; } else { S1 = "0" ; } if ( B !== "0" ) { S2 = ( ( ( B / b ) / J ) * K * b ) ; } else { S2 = "0" ; } if ( C !== "0" ) { S3 = ( ( ( C / c ) / J ) * K * c ) ; } else { S3 = "0" ; } if ( D !== "0" ) { S4 = ( ( ( D / d ) / J ) * K * d ) ; } else { S4 = "0" ; } if ( E !== "0" ) { S5 = ( ( ( E / e ) / J ) * K * e ) ; } else { S5 = "0" ; } if ( F !== "0" ) { S6 = ( ( ( F / f ) / J ) * K * f ) ; } else { S6 = "0" ; } I = S1 + S2 + S3 + S4 + S5 + S6 ; if(!isNaN(H)) {$jq("span.es-result-span-h").text(H.toFixed(2));} else{$jq("span.es-result-span-h").text('Error: Please enter numerals only');} if(!isNaN(I)) {$jq("span.es-result-span-i").text(I.toFixed(2));} else{$jq("span.es-result-span-i").text('Error: Please enter numerals only');} }); });

    Read the article

  • Connect to WEP Wireless Network by command line on Ubuntu

    - by Tim
    Hi, I am a newbie to both network and Linux. I am now trying to connect to a WEP wireless network by command line on my Ubuntu 8.10, because the Network Manager does not support 64 bit WEP. (1) I firstly bring down the Network Manager and then try to connect to a wireless network, whose essid is candy and password is 5673212741. But it fails as shown in the following. I wonder why and how to do it correctly? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwconfig wlan0 essid candy opendo iwconfig wlan0 key 18018ce78e open $ sudo iwconfig wlan0 key 5673212741 open $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 9971 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. $ ping www.bbc.co.uk ping: unknown host www.bbc.co.uk (2) A less important question: why the scan for wireless networ does not work after I bring down the Network Manager? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning : Network is down Thanks and regards!

    Read the article

  • Calculating IOPS for a single HDD - what am I doing wrong?

    - by red888
    So I know there is no standardized way of calculating IOPS for a HDD, but from everything I have read it appears one of the most accurate formulas is the following: IOP/ms = + {rotational latency} + ({block size} / {data transfer rate}) Which is IOs per millisecond or what the book I've been reading calls "Disk Service Time". Also rotational latency is calculated as half of one rotation in milliseconds. This was taken from the EMC book "Information Storage and Management" -arguably a pretty reliable source right\wrong? Putting this formula into practice consider this Seagate data sheet. I am going to calculate IOPS for the ST3000DM001 model for a block size of 4kb: Seek Average (Write) = 9.5 -I'll measuring IOPS for writes Spindle speed = 7200rpm Average Data Rate = 156MB/s So my variables are: Seek Time = 9.5ms Rotational latency = (.5 / (7200rpm / 60)) = 0.004s = 4ms Data Rate = 156MB/s = (0.156MB/ms / 0.004MB) = 39 9.5ms + 4ms + 39 = IO/ms 52.5 1 / (52.5 * 0.001) = 19 IOPS 19 IOPS for this drive clearly is not right so what am I doing wrong?

    Read the article

  • Archive Outlook mail items into SQL Server

    - by marc_s
    I am looking (and so far not finding any) for a solution to archive e-mail items from my Outlook into SQL Server. My PST is beginning to get really really big, and I'd love to extract my older e-mail into SQL Server in a way so I can still easily find mails if needed. I would prefer SQL Server as the storage medium since I'm familiar with it, and it's rock solid - I don't want to have a collection of PST files or CHM files or anything like that. Does anyone know of such a solution? I'm a power/home user - I can't afford $5'000 enterprise licenses - I need a sub-$100 solution for private use.

    Read the article

  • Recommending simple appliance for DansGuardian, iptables, snort inline

    - by SRobertJames
    I'm currently using a Linksys E2000 with dd-wrt. I'd like to add DansGuardian for Content Filtering and snort-inline for IPS; but those require a more powerful box (mainly, more storage). Can you recommend a good device to use? I'm open to both overwrite-the-firmware (like dd-wrt) and designed-to-be-customized boxes. Requirements: 1. 5+ Ethernet ports, pref. GigE 2. small form factor 3. No noise (office environment) 4. low power 5. Not sure about 802.11 wireless Budget < $400, pref. less.

    Read the article

  • How to re-add a RAID-10 failed drive on Ubuntu?

    - by thiesdiggity
    I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

    Read the article

  • What are performance limits of a database?

    - by Tommy
    What are some rough performance limits (read/s, write/s) for a single database server (no master-slave architecture), assuming storage on disk? How many read/s, write/s, depending on the kind of disk? (SSD vs non-SSD) , assuming simple operations (select one row by primary key, update one row, correctly indexed). I assume this limit is dependent on disk seek/write. EDIT: My question is more about getting rough metrics of the number of operations a database supports: to be able to know for example, if a new feature triggering 300 inserts/s can be supported without scaling out with additional servers.

    Read the article

  • Why my Ldirectord check multiple times on read server every interval?

    - by garconcn
    I have a Ldirectord server and two real servers. My ldirectord used to check the request page on real server once in every interval, but now I found that it check four times. I have monitored the log on both real servers, they have the same problem. Here is my ldirectord configuration: checktimeout=10 checkinterval=5 autoreload=yes logfile="/var/log/ldirectord.log" quiescent=no virtual=192.168.1.100:80 fallback=127.0.0.1:80 real=192.168.1.10:80 gate real=192.168.1.20:80 gate service=http request="lb.html" receive="still alive" scheduler=sh persistent=60 protocol=tcp checktype=negotiate Ldirectord will connect to each real server once every 5 seconds (checkinterval) and request 192.168.0.10:80/test.html (real/request). The access log in real server: 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805"

    Read the article

  • Connect to Nonencrypted Wireless Network Using Ubuntu Commands

    - by Tim
    I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

    Read the article

  • Hyper-V vss-writer not making current copies

    - by Martinnj
    I'm using diskshadow to backup live Hyper-V machines on a Windows 2008 server. The backup consists of 3 scripts, the first will create the shadow copies and expose them, the second uses robocopy to copy them to a remote location and the third unexposes the shadow copies again. The first script – the one that runs correctly but fails to do what it's supposed to: # DiskShadow script file to backup VM from a Hyper-V host # First, delete any shadow copies of the drives. System Drives needs to be included. Delete Shadows volume C: Delete Shadows volume D: Delete Shadows volume E: #Ensure that shadow copies will persist after DiskShadow has run set context persistent # make sure the path already exists set verbose on begin backup add volume D: alias VirtualDisk add volume C: alias SystemDrive # verify the "Microsoft Hyper-V VSS Writer" writer will be included in the snapshot # NOTE: The writer GUID is exclusive for this install/machine, must be changed on other machines! writer verify {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} create end backup # Backup is exposed as drive X: make sure your drive letter X is not in use Expose %VirtualDisk% X: Exit The next is just a robocopy and then an unexpose. Now, when I run the above script, I get no errors from it, except that the "BITS" writer has been excluded because none of its components are included. That's okay because I really only need the Hyper-V writer. Also I double checked the GUID for the writer, it's correct. During the time when the Hyper-V writer becomes active, 2 things will happen on the guest machines: The Debian/Linux machine will go to a saved state and restore when done, all fine. The Windows guests will "creating vss snapshop-sets" or something similar. Then X: gets exposed and I can copy the .vhd files over. The problem is, for some reason, the VHD files I get over seems to be old copies, they miss files, users and updates that are on the actual machines. I also tried putting the machines in a saved sate manually, didn't change the outcome. I hope someone here has an idea of how to solve this.

    Read the article

  • How do I reinitialise a failed RAID 5 drive using terminal on Ubuntu Server

    - by Stephen
    I've currently put together a new system and part of that has been creating a software RAID 5 using 'mdadm' in Ubuntu Server. I successfully got to the point where I create the array using: sudo mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 I left it to do its thing overnight then used the following command to check on it: watch cat /proc/mdstat To which the following was returned: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdd1[4](S) sdc1[2] sdb1[1] sda1[0](F) 5860535808 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/2] [_UU_] unused devices: <none> It appears that one has failed (and I'm not too savvy with why another is a spare). So, just to be sure that something else isn't amiss I wanted to try and re-engage the failed drive. Can someone explain how I can do that and what I should do with the spare (if anything). And also how do I know when synchronisation is complete? The tutorial I used to get this far is located here: http://sonniesedge.co.uk/2009/06/13/software-raid-5-on-ubuntu-904/ Many thanks! p.s. Here is some extra information that may help: sudo mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Mon Jun 18 21:14:21 2012 Raid Level : raid5 Array Size : 5860535808 (5589.04 GiB 6001.19 GB) Used Dev Size : 1953511936 (1863.01 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Mon Jun 18 21:50:26 2012 State : clean, FAILED Active Devices : 2 Working Devices : 3 Failed Devices : 1 Spare Devices : 1 Layout : left-symmetric Chunk Size : 512K Name : myraidbox:0 (local to host myraidbox) UUID : a269ee94:a161600c:fb1665e7:bd2f27b3 Events : 13 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 3 0 0 3 removed 0 8 1 - faulty spare /dev/sda1 4 8 49 - spare /dev/sdd1

    Read the article

  • System has reached the maximum size allowed for the system part of the registry

    - by Bob Denny
    To be precise System has reached the maximum size allowed for the system part of the registry. Additional storage requests will be ignored. WinXP/64 running fine for 2 years (no /3Gb switch), just started happening. I used ntregopt and the problem went away at least temporarily. However, looking before and after in Windows\System32\Config I see that my System file was reduced only by 10% and is still 170+ Mb. According to my rather extensive research with Google, this is "huge" and should be more like 10-20Mb. The system runs fine. There is a System.bak that is only 11Mb and has the date when I ran ntregopt. That's what I know. Now my question: Is there anything I can do to reduce or rebuild the System registry hive given the above info?

    Read the article

  • Can someone explain the physical architecture of RAID 10 in complete layman's terms?

    - by Hank
    I am a newbie in the world of storage and I am having a hard time digesting the physical architecture of some of the RAID levels. I am particularly interested in RAID 10, and 50. I asked the question specifically about RAID 10, because I feel if I understand that, I'll understand the other. So, I get the definition of RAID 10 - "minimum 4 disks, a striped array whose segments are mirrored". If I've got 4 disks and Disks 1 and 2 are a mirrored pair, and Disks 3 and 4 are a mirrored pair - where does the data get striped? Thanks.

    Read the article

< Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >