Search Results

Search found 18911 results on 757 pages for 'device manager'.

Page 169/757 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

• Why do I see a large performance hit with DRBD?

  - by BHS

  I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

  Read the article

• Auto-select external soundcard?

  - by dandelion

  Just got an external usb sound card because my internal speakers broke. The new sound card works just fine after plugging it in and going to System Settings Sound, and then selecting the device. However, I was curious as to whether there was a way to make ubuntu auto-select the device without having to go through System Settings. Can it just be selected upon plugging it in? Any and all help appreciated :)) (ps its running 12.04)

  Read the article

• Haack and Walther join the speaker lineup at Web Camp Redmond!

  - by Latest Microsoft Blogs

    The Web Camp in Redmond on Friday 18th and Saturday 19th June is starting to shape up nicely with some last minute speakers added to the roster !  Phil Haack the Program Manager for ASP.NET MVC and Stephen Walther the Program Manager for Ajax Read More......(read more)

  Read the article

• ath9k driver does not weak up

  - by shantanu

  I know this is common question but i found no suitable answer, so i am asking this again. I installed ubuntu 11.10. I found the bug for ath9k, so set first network boot from BIOS menu. That's worked. I have upgraded to 12.04 yesterday. Now ath9k is creating problem again. First network boot is still enable. ath9k works at start. But failed(connect again and again) after couple of minutes. dmesg show error that it can not weak up in 500us. So i tried #compat-wireless-3.5.1-1. But result is same. I have also added #nohwcrypt=1 option in /etc/modeprob.d/ath9k.conf. Still no luck. I tried #rmmod and then modprobe sudo modprobe ath9k nohwcrypt=1 dmesg shows me error: [ 400.690086] ath9k: Driver unloaded [ 406.214329] ath9k 0000:06:00.0: enabling device (0000 -> 0002) [ 406.214348] ath9k 0000:06:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 406.214368] ath9k 0000:06:00.0: setting latency timer to 64 [ 406.428517] ath9k 0000:06:00.0: Failed to initialize device [ 406.428852] ath9k 0000:06:00.0: PCI INT A disabled [ 406.428887] ath9k: probe of 0000:06:00.0 failed with error -5 dmesg error when driver fail: 355.023521] ath: Chip reset failed [ 355.023524] ath: Unable to reset channel, reset status -22 [ 355.023556] ath: Unable to set channel [ 355.088569] ath: Failed to stop TX DMA, queues=0x10f! [ 355.122708] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff [ 355.122714] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up [ 355.263962] ath: Chip reset failed [ 355.263966] ath: Unable to reset channel (2437 MHz), reset status -22 [ 358.996063] ath: Failed to wakeup in 500us [ 364.004182] ath: Failed to wakeup in 500us I can not install fresh ubuntu because i have lots of application installed. System : Acer Aspire 4250 AMD dual core 1.6GHZ Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) EDITED Now i am in serious problem. No wifi device is not showing in ifconfig or lshw commands. Only ether-net interface shows. I tried (FN + WIFI) several times to enable the device but nothing helps. Now I have installed fresh ubuntu 12.04. Please help lshw -c network: *-network description: Ethernet interface product: 82566DC Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 02 serial: 00:19:d1:7a:8e:f9 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=2.0.0-k duplex=full firmware=1.1-0 ip=192.168.1.114 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:90300000-9031ffff memory:90324000-90324fff ioport:20c0(size=32) rfkill command does not show anything but no error.

  Read the article

• wireless LAN soft blocked on Ubuntu 13.10

  - by iacopo

  I've troubles with bluetooth and with lan. When I digit: rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: yes Hard blocked: no When I digit: lspci -v 00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Root Complex Subsystem: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Root Complex Flags: bus master, 66MHz, medium devsel, latency 0 00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Trinity [Radeon HD 7600G] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Trinity [Radeon HD 7600G] Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at c0000000 (32-bit, prefetchable) [size=256M] I/O ports at f000 [size=256] Memory at feb00000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at [disabled] Capabilities: Kernel driver in use: radeon 00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Trinity HDMI Audio Controller Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Trinity HDMI Audio Controller Flags: bus master, fast devsel, latency 0, IRQ 49 Memory at feb44000 (32-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at feb48000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: xhci_hcd 00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 40) (prog-if 01 [AHCI 1.0]) Subsystem: Advanced Micro Devices, Inc. [AMD] Device 7800 Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 45 I/O ports at f190 [size=8] I/O ports at f180 [size=4] I/O ports at f170 [size=8] I/O ports at f160 [size=4] I/O ports at f150 [size=16] Memory at feb50000 (32-bit, non-prefetchable) [size=2K] Capabilities: Kernel driver in use: ahci 00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 Memory at feb4f000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci 00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11) (prog-if 20 [EHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17 Memory at feb4e000 (32-bit, non-prefetchable) [size=256] Capabilities: Kernel driver in use: ehci-pci 00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 Memory at feb4d000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci 00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11) (prog-if 20 [EHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17 Memory at feb4c000 (32-bit, non-prefetchable) [size=256] Capabilities: Kernel driver in use: ehci-pci 00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 14) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller Flags: 66MHz, medium devsel Kernel driver in use: piix4_smbus 00:14.1 IDE interface: Advanced Micro Devices, Inc. [AMD] FCH IDE Controller (prog-if 8a [Master SecP PriP]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH IDE Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at f100 [size=16] Kernel driver in use: pata_atiixp 00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 01) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller Flags: bus master, slow devsel, latency 32, IRQ 16 Memory at feb40000 (64-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge Flags: bus master, 66MHz, medium devsel, latency 0 00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD] FCH PCI Bridge (rev 40) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, medium devsel, latency 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 Memory at feb4b000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci 00:14.7 SD Host controller: Advanced Micro Devices, Inc. [AMD] FCH SD Flash Controller (prog-if 01) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH SD Flash Controller Flags: bus master, 66MHz, medium devsel, latency 39, IRQ 16 Memory at feb4a000 (64-bit, non-prefetchable) [size=256] Kernel driver in use: sdhci-pci 00:15.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 0) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff Capabilities: Kernel driver in use: pcieport 00:15.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 1) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: fe900000-feafffff Capabilities: Kernel driver in use: pcieport 00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 0 Flags: fast devsel 00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 1 Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 2 Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 3 Flags: fast devsel Capabilities: Kernel driver in use: k10temp 00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 4 Flags: fast devsel 00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 5 Flags: fast devsel 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07) Subsystem: PC Partner Limited / Sapphire Technology Device 0123 Flags: bus master, fast devsel, latency 0, IRQ 46 I/O ports at e000 [size=256] Memory at d0004000 (64-bit, prefetchable) [size=4K] Memory at d0000000 (64-bit, prefetchable) [size=16K] Capabilities: Kernel driver in use: r8169 03:00.0 Network controller: Ralink corp. RT3290 Wireless 802.11n 1T/1R PCIe Subsystem: AzureWave Device 2b87 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at fea40000 (32-bit, non-prefetchable) [size=64K] Memory at fea30000 (32-bit, non-prefetchable) [size=64K] Capabilities: Kernel driver in use: rt2800pci 03:00.1 Bluetooth: Ralink corp. RT3290 Bluetooth Subsystem: AzureWave Device 2787 Flags: bus master, fast devsel, latency 0, IRQ 11 Memory at fea20000 (32-bit, non-prefetchable) [size=64K] Memory at fea10000 (32-bit, non-prefetchable) [size=64K] Memory at fe900000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at fea00000 [disabled] [size=64K] Capabilities: Thank you for all the help

  Read the article

• The Latest JD Edwards World Technical Enhancements

  Tom Carrell, Principal Product Strategy Manager and Mike Jepkes, Senior Technical Development Manager for JD Edwards World products discuss with Cliff how customers can take full advantage of web enablement, service enablement along with many other new JD Edwards World technical enhancements.

  Read the article

• Various roles in an Organization and their respective tasks.

  - by balu

  In various organizations(Software Company) there would be various designations having different roles. I would like to know the Industry accepted & followed trend in the organization hierarchy(..Like DBA,System Architect,Project Manager,Senior Developer,Developer,QA,Design Team,Delivery Manager etc..).And the various roles played by each of them in the various stages of the Software Development Life Cycle.Who all could possibly be sharing the responsibility mutually?

  Read the article

• Available OPN Specialization Categories & Specializations

  - by [email protected]

  DatabaseOracle Data Warehousing Specialization CriteriaOracle Database 11g Specialization CriteriaOracle Enterprise Linux Specialization CriteriaOracle Enterprise Manager Specialization Criteria MiddlewareOracle Service-Oriented Architecture Specialization CriteriaOracle Business Intelligence Foundation Specialization CriteriaOracle Enterprise ManagerOracle Enterprise Manager Specialization CriteriaOracle Enterprise LinuxOracle Enterprise Linux Specialization CriteriaAll Available Specializationshttps://competencycenter.oracle.com/opncc/glp_list.cc

  Read the article

• ATI Radeon HD 4650 AGP Video card not recognized properly

  - by PastorLarry

  I have an ASUS ATI Radeon HD 4650 AGP in this system (yeah, I know how old it is). I've been on Ubuntu since 10.04, and the system has never properly recognized the card. I have always had the VESA drivers installed. Now that I have the time to address the problem, 12.04 was listing the card as "Unknown" under the System Settings. Meanwhile, Sysinfo recognizes the card as: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 0028 So I know that this card should be using the radeon driver (or even the radeonhd driver). However, when I installed the mesa-utils package, the card is suddenly reported as: Gallium 0.4 on llvmpipe (LLVM 0x300) So now, I'm completely at a loss. It seems that the llvmpipe stuff has to do with OpenGL, but it still appears that I don't have the proper video driver installed. That being said, anyone know what I can do to force the system to recognize the card and use the radeon driver? [EDIT 05.28] I did look at some other information, including glxinfo and a couple of other commands (it was REALLY late, so I don't remember the other commands) and I got these: glxinfo | grep vendor: server glx vendor string: SGI client glx vendor string: Mesa Project and SGI OpenGL vendor string: X.org glxinfo | grep renderer: OpenGL renderer string: Gallium 0.4 on AMD RV730 One of the other commands gave a whole lot of info and near the end stated that the activation string for the radeon driver was "modprobe radeon". I've tried that from sudo and as root, but it doesn't seem to change anything. I'm at a complete loss. I've even added the xorg-edgers ppa to my Software Sources and updated and rebooted the system, but nothing has changed. Most of all, I can't seem to find any documentation on this issue, as it seems that it's assumed that the radeon driver will install automatically, no questions asked. I feel like such a newbie. Does anyone have any ideas on this? [edit 05.28] results of lsmod | grep radeon (in a more readable format than the comment below): radeon 733693 3 ttm 65344 1 radeon drm_kms_helper 45466 1 radeon drm 197692 5 radeon,ttm,drm_kms_helper i2c_algo_bit 13199 1 radeon [edit 05.29] This is my /etc/X11/xorg.conf: Section "ServerLayout" Identifier "aticonfig Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 EndSection Section "Module" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" So here is my question. Can I simply change the name of the driver in the device section to "radeon" instead of "fglrx" and have the radeon driver work? Or is ther a way to use this as a tmeplate and change the appropriate lines and activate the radeon driver through this file?

  Read the article

• How to connect nokia lumis 520 to ubuntu 12.04

  - by pavankumar

  i have done following steps sudo add-apt-repository ppa:langdalepl/gvfs-mtp sudo apt-get update and updated some upgrades from update manager after doing above steps i am able to see lumia phone name in file system.But when i try to mount device i am getting following errors Unable to mount RM-914|Nokia Lumia 520 Unable to open MTP device '[usb:001,010]' is there any way to solve these problem?

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• Before the Summit of 2012

  - by Ajarn Mark Caldwell

  Today, Monday, was the first day of the PASS Summit Preconference training events, but instead I spent the day at the free SQL in the City event put on by Red Gate. For me this was not a financial decision (pre-con sessions cost extra above the general Summit registration) but rather a matter of interest.  I had already included money for pre-cons in this year’s training budget, but none of them really stood out to me, so even if the Red-Gate event were not going on at the same time, I probably would not have gone to any pre-cons this year.  However, the topics being presented at the SQL in the City event were of great interest to me.  There promised to be good information on Continuous Integration and automated deployment of database changes, which lately has been a real hot topic at my work.  And indeed, Red-Gate announced the release of a new tool (still in Early Access Program…a.k.a. Beta) which is called the Deployment Manager.  Since we are in the middle of a TFS implementation project, it will be interesting to see how this plays out and compares to what we put together with the automated builds in TFS.  But, as I understand it, the primary focus of Deployment Manager is not to be the Build process (Red Gate uses JetBrains’ Team City for that in their shop) but rather to aid in the deployment of those build packages, as well as providing easy rollback and a good visualization of which versions of software are in which environments.  It looks promising and I’ve already downloaded the installer package to play with it later. Overall, I was quite impressed with the SQL in the City event.  Having heard many current and past members of the PASS Board of Directors describe the challenges of putting on a large conference, and the growing pains that the PASS Summit has gone through, I am even more impressed that the Red Gate event ran as smoothly as it did.  And it is quite impressive the amount of money that Red Gate must have spent given that this was a no-charge event to attend, they had a very nice hot lunch, and the after-event drinks celebration.  Well done, folks! Of course it was great to hear from a variety of speakers.  Today I listened to some folks from Red Gate like Grant Fritchey (blog | @GFritchey) and David Atkinson (Product Manager for SQL Source Control and now the Deployment Manager tool set); and also Brent Ozar (blog | @BrentO) and Buck Woody (blog | @BuckWoody).  By the way, if you have never seen either Brent or Buck speak, you really should.  Different styles, but both are very entertaining and educational at the same time.  I love Buck’s sense of humor (here’s a tip…don’t be late to Buck’s session or you’ll become part of the presentation) and I praise Brent’s slides.  Brent’s style very much reminds me of that espoused by Garr Reynolds on his Presentation Zen blog (and book) and I am impressed that he can make a technical presentation so engaging. It was a great day, a great way to kick off the week, and I am excited to get into the full Summit!

  Read the article

• New security configuration flag in UCM PS3

  - by kyle.hatlestad

  While the recent Patch Set 3 (PS3) release was mostly focused on bug fixes and such, a new configuration flag was added for security. In 10gR3 and prior versions, UCM had a component called Collaboration Manager which allowed for project folders to be created and groups of users assigned as members to collaborate on documents. With this component came access control lists (ACL) for content and folders. Users could assign specific security rights on each and every document and folder within a project. And it was possible to enable these ACL's without having the Collaboration Manager component enabled. But it took some special instructions (see technote# 603148.1) and added some extraneous pieces still related to Collaboration Manager. When 11g came out, Collaboration Manager was no longer available. But the configuration settings to turn on ACLs were still there. Well, in PS3 they've been cleaned up a bit and a new configuration flag has been added to simply turn on the ACL fields and none of the other collaboration bits. To enable ACLs: UseEntitySecurity=true Along with this configuration flag to turn ACLs on, you also need to define which Security Groups will honor the ACL fields. If an ACL is applied to a content item with a Security Group outside this list, it will be ignored. SpecialAuthGroups=HumanResources,Legal,Marketing Save the settings and restart the instance. Upon restart, two new metadata fields will be created: xClbraUserList, xClbraAliasList. If you are using OracleTextSearch as the search indexer, be sure to run a Fast Rebuild on the collection. On the Check In, Search, and Update pages, values are added by simply typing in the value and getting a type-ahead list of possible values. Select the value, click Add and then set the level of access (Read, Write, Delete, or Admin). If all of the fields are blank, then it simply falls back to just Security Group and Account access. As for how they are stored in the metadata fields, each entry starts with it's identifier: ampersand (&) symbol for users, "at" (@) symbol for groups, and colon (:) for roles. Following that is the entity name. And at the end is the level of access in paranthesis. e.g. (RWDA). And each entry is separated by a comma. So if you were populating values through batch loader or an external source, the values would be defined this way. Detailed information on Access Control Lists can be found in the Oracle Fusion Middleware System Administrator's Guide for Oracle Content Server.

  Read the article

• Webcast Replay Available: SOA Integration Options for E-Business Suite

  - by BillSawyer

  I am pleased to release the replay and presentation for the latest ATG Live Webcast: SOA Integration Options for E-Business Suite (Presentation)Abhishek Verma, Manager, Applications Technology Group and Rajesh Ghosh, Group Manager, ATG Development discussed the web service and SOA integration options for Oracle E-Business Suite. The presentation covered Oracle's integration tools and technologies, including the Oracle Applications Adapter and the Integrated SOA Gateway.Finding other recorded ATG webcastsThe catalog of ATG Live Webcast replays, presentations, and all ATG training materials is available in this blog's Webcasts and Training section.

  Read the article

• SSIS: Deploying OLAP cubes using C# script tasks and AMO

  - by DrJohn

  As part of the continuing series on Building dynamic OLAP data marts on-the-fly, this blog entry will focus on how to automate the deployment of OLAP cubes using SQL Server Integration Services (SSIS) and Analysis Services Management Objects (AMO). OLAP cube deployment is usually done using the Analysis Services Deployment Wizard. However, this option was dismissed for a variety of reasons. Firstly, invoking external processes from SSIS is fraught with problems as (a) it is not always possible to ensure SSIS waits for the external program to terminate; (b) we cannot log the outcome properly and (c) it is not always possible to control the server's configuration to ensure the executable works correctly. Another reason for rejecting the Deployment Wizard is that it requires the 'answers' to be written into four XML files. These XML files record the three things we need to change: the name of the server, the name of the OLAP database and the connection string to the data mart. Although it would be reasonably straight forward to change the content of the XML files programmatically, this adds another set of complication and level of obscurity to the overall process. When I first investigated the possibility of using C# to deploy a cube, I was surprised to find that there are no other blog entries about the topic. I can only assume everyone else is happy with the Deployment Wizard! SSIS "forgets" assembly references If you build your script task from scratch, you will have to remember how to overcome one of the major annoyances of working with SSIS script tasks: the forgetful nature of SSIS when it comes to assembly references. Basically, you can go through the process of adding an assembly reference using the Add Reference dialog, but when you close the script window, SSIS "forgets" the assembly reference so the script will not compile. After repeating the operation several times, you will find that SSIS only remembers the assembly reference when you specifically press the Save All icon in the script window. This problem is not unique to the AMO assembly and has certainly been a "feature" since SQL Server 2005, so I am not amazed it is still present in SQL Server 2008 R2! Sample Package So let's take a look at the sample SSIS package I have provided which can be downloaded from here: DeployOlapCubeExample.zip  Below is a screenshot after a successful run. Connection Managers The package has three connection managers: AsDatabaseDefinitionFile is a file connection manager pointing to the .asdatabase file you wish to deploy. Note that this can be found in the bin directory of you OLAP database project once you have clicked the "Build" button in Visual Studio TargetOlapServerCS is an Analysis Services connection manager which identifies both the deployment server and the target database name. SourceDataMart is an OLEDB connection manager pointing to the data mart which is to act as the source of data for your cube. This will be used to replace the connection string found in your .asdatabase file Once you have configured the connection managers, the sample should run and deploy your OLAP database in a few seconds. Of course, in a production environment, these connection managers would be associated with package configurations or set at runtime. When you run the sample, you should see that the script logs its activity to the output screen (see screenshot above). If you configure logging for the package, then these messages will also appear in your SSIS logging. Sample Code Walkthrough Next let's walk through the code. The first step is to parse the connection string provided by the TargetOlapServerCS connection manager and obtain the name of both the target OLAP server and also the name of the OLAP database. Note that the target database does not have to exist to be referenced in an AS connection manager, so I am using this as a convenient way to define both properties. We now connect to the server and check for the existence of the OLAP database. If it exists, we drop the database so we can re-deploy. svr.Connect(olapServerName); if (svr.Connected) { // Drop the OLAP database if it already exists Database db = svr.Databases.FindByName(olapDatabaseName); if (db != null) { db.Drop(); } // rest of script } Next we start building the XMLA command that will actually perform the deployment. Basically this is a small chuck of XML which we need to wrap around the large .asdatabase file generated by the Visual Studio build process. // Start generating the main part of the XMLA command XmlDocument xmlaCommand = new XmlDocument(); xmlaCommand.LoadXml(string.Format("<Batch Transaction='false' xmlns='http://schemas.microsoft.com/analysisservices/2003/engine'><Alter AllowCreate='true' ObjectExpansion='ExpandFull'><Object><DatabaseID>{0}</DatabaseID></Object><ObjectDefinition/></Alter></Batch>", olapDatabaseName));  Next we need to merge two XML files which we can do by simply using setting the InnerXml property of the ObjectDefinition node as follows: // load OLAP Database definition from .asdatabase file identified by connection manager XmlDocument olapCubeDef = new XmlDocument(); olapCubeDef.Load(Dts.Connections["AsDatabaseDefinitionFile"].ConnectionString); // merge the two XML files by obtain a reference to the ObjectDefinition node oaRootNode.InnerXml = olapCubeDef.InnerXml;   One hurdle I had to overcome was removing detritus from the .asdabase file left by the Visual Studio build. Through an iterative process, I found I needed to remove several nodes as they caused the deployment to fail. The XMLA error message read "Cannot set read-only node: CreatedTimestamp" or similar. In comparing the XMLA generated with by the Deployment Wizard with that generated by my code, these read-only nodes were missing, so clearly I just needed to strip them out. This was easily achieved using XPath to find the relevant XML nodes, of which I show one example below: foreach (XmlNode node in rootNode.SelectNodes("//ns1:CreatedTimestamp", nsManager)) { node.ParentNode.RemoveChild(node); } Now we need to change the database name in both the ID and Name nodes using code such as: XmlNode databaseID = xmlaCommand.SelectSingleNode("//ns1:Database/ns1:ID", nsManager); if (databaseID != null) databaseID.InnerText = olapDatabaseName; Finally we need to change the connection string to point at the relevant data mart. Again this is easily achieved using XPath to search for the relevant nodes and then replace the content of the node with the new name or connection string. XmlNode connectionStringNode = xmlaCommand.SelectSingleNode("//ns1:DataSources/ns1:DataSource/ns1:ConnectionString", nsManager); if (connectionStringNode != null) { connectionStringNode.InnerText = Dts.Connections["SourceDataMart"].ConnectionString; } Finally we need to perform the deployment using the Execute XMLA command and check the returned XmlaResultCollection for errors before setting the Dts.TaskResult. XmlaResultCollection oResults = svr.Execute(xmlaCommand.InnerXml);  // check for errors during deployment foreach (Microsoft.AnalysisServices.XmlaResult oResult in oResults) { foreach (Microsoft.AnalysisServices.XmlaMessage oMessage in oResult.Messages) { if ((oMessage.GetType().Name == "XmlaError")) { FireError(oMessage.Description); HadError = true; } } } If you are not familiar with XML programming, all this may all seem a bit daunting, but perceiver as the sample code is pretty short. If you would like the script to process the OLAP database, simply uncomment the lines in the vicinity of Process method. Of course, you can extend the script to perform your own custom processing and to even synchronize the database to a front-end server. Personally, I like to keep the deployment and processing separate as the code can become overly complex for support staff.If you want to know more, come see my session at the forthcoming SQLBits conference.

  Read the article

• Recorded Webcast Available: Extend SCOM to Optimize SQL Server Performance Management

  - by KKline

  Join me and Eric Brown, Quest Software senior product manager for SQL Server monitoring tools, as we discuss the server health-check capabilities of Systems Center Operations Manager (SCOM) in this previously recorded webcast. We delve into techniques to maximize your SCOM investment as well as ways to complement it with deeper monitoring and diagnostics. You’ll walk away from this educational session with the skills to: Take full advantage of SCOM’s value for day-to-day SQL Server monitoring Extend...(read more)

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

• John Hitchcock of Pace Describes the Oracle Agile PLM Customer Experience

  John Hitchcock, Senior Manager of Configuration Management at Pace (formerly 2Wire, Inc.), sat down for an interview during Oracle's Innovation Summit with Kerrie Foy, Manager of PLM Product Marketing at Oracle. Learn why his organization upgraded to the latest version of Agile and expanded the footprint to achieve impressive savings and productivity gains across the global, networked product value-chain.

  Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >