Search Results

Search found 531 results on 22 pages for 'blacklist prevention'.

Page 17/22 | < Previous Page | 13 14 15 16 17 18 19 20 21 22  | Next Page >

  • Atheros wireless not working

    - by Chandru1
    I have been struggling hard since i have installed Ubuntu 10.10 but it has been difficult for me to get my wifi working. So here is what i tried. First i checked whether i have the driver using the ifconfig command and it shows the wireless lan driver as wlan0. Next, i tried the command iwlist wlan0 scanning by becoming the root which gave me the output as no scan results. Next, i visited this link https://help.ubuntu.com/community/WifiDocs/Driver/Atheros to see as to what problem my laptop may have. I do own have an ath5k chipset. And as i followed the instructions in the above link in one of the blacklist-ath_pci.conf file had this written in it. For some Atheros 5K RF MACs, the madwifi driver loads buts fails to correctly initialize the hardware, leaving it in a state from which ath5k cannot recover. To prevent this condition, stop madwifi from loading by default. Use Jockey to select one driver or the other. (Ubuntu: #315056, #323830 I am not that good at Linux but i have given it a try. I am desperate to have my wifi working and i would be glad if this community could help. ADDED: If anyone would like to know as to what drivers i am using this is the output. network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wlan0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath5k driverversion=2.6.35-24-generic firmware=N/A latency=168 link=no maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11bg resources: irq:18 memory:d0000000-d000ffff Some more information and output as to what i have done. lsmod | grep ath ath5k 130083 0 mac80211 231541 1 ath5k ath 8153 1 ath5k cfg80211 144470 3 ath5k,mac80211,ath led_class 2633 1 ath5k

    Read the article

  • How do i disable intel graphics in a hybrid graphics setup?

    - by Eshwar
    Hi, I have a Dell Vostro 3700 version A10. The relevant bits from lspci -v | grep VGA are: 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) and 01:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 330M] (rev a2) so as you can see this is one of those hybrid graphics laptops. Now, I have no interest in any kind of switching. I would like to completely disable the Intel Graphics thats on the processor. I checked in the xorg.log file and it shows that the intel card is in use. from lsmod i see it uses the i915 module. I tried blacklisting that module in /etc/modprobe.d/blacklist.conf but that didn't really work because i still couldn't use the nvidia card for display. I wish there was a BIOS option to disable, but there isn't. Some people have also suggested changing the SATA mode to compatibility, but that does not work either in this case as the intel vga controller still shows up in lspci I tried setting the busid manually in the /etc/X11/xorg.conf file but it still didn't work. It gave me an error that said something along the lines of screen not detected. any bits of xorg.log that you'd like me to attach? So what I am looking for is some solution that allows me to completely disable the use of the intel vga controller. if it was blocked somehow it'd be nice. as if it were not present. Any suggestions? I am desperate here actually. Because I cannot use the HDMI port right now on my laptop for that reason. My guess is this applies to desktops that also have Core i5 processors with onchip graphics as well as dedicated graphics cards. How would they go about solving the problem?

    Read the article

  • Qualcomm Gobi WWAN modem no longer appears in Network Manager

    - by Andy E
    Not sure what happened here. I installed Cinnamon on my Ubuntu 12.10 environment yesterday, rebooted when finished and everything was working fine. I even used my WWAN modem after my fixed line broadband went down. However, after starting my machine this morning and seeing that my fixed line is still having problems (intermittently), I clicked the network applet and my WWAN device wasn't listed. It's not in the main network manager window either. It is still present on the system, however: $ lsusb Bus 001 Device 003: ID 05ca:18b0 Ricoh Co., Ltd Sony Vaio Integrated Webcam Bus 001 Device 004: ID 05c6:9221 Qualcomm, Inc. Gobi Wireless Modem (QDL mode) Bus 002 Device 005: ID 04e8:6865 Samsung Electronics Co., Ltd Bus 002 Device 002: ID 0409:005a NEC Corp. HighSpeed Hub Bus 003 Device 002: ID 147e:1000 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 008 Device 002: ID 044e:3017 Alps Electric Co., Ltd BCM2046 Bluetooth Device Debug output from modem-manager, refers to a device that is blacklisted: modem-manager[10186]: [1355478137.024491] [mm-manager.c:866] device_added(): (tty/ttyUSB0): port's parent device is blacklisted modem-manager[10186]: [1355478137.024607] [mm-manager.c:875] device_added(): (tty/ttyS0): port's parent platform driver is not whitelisted modem-manager[10186]: [1355478137.024700] [mm-manager.c:875] device_added(): (tty/ttyS1): port's parent platform driver is not whitelisted ... I couldn't see anything relevant in the debug output for network-manager, but I've created a paste for it just in case. In /lib/udev/rules.d/77-mm-qdl-device-blacklist.rules, I found the following line that matches the device IDs from the lsusb output: # Generic Gobi QDL device ATTRS{idVendor}=="05c6", ATTRS{idProduct}=="9221", ENV{ID_MM_DEVICE_IGNORE}="1" I tried commenting out the second line and restarting network-manager/modem-manager but it didn't help. I've no idea where to go from here, does anyone else have any ideas?

    Read the article

  • HP Envy 15 3040nr sound issues

    - by Lenny
    I have successfully set up my Envy 15" for Ubuntu 12.04 except for the sound, anyone have any ideas about how to get it working? I had to blacklist snd-usb-audio to my alsa to stop pulseaudio from freezing on login and logout, but now no sound plays. Could anyone provide me with some guidance? lspci info 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:01.2 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) 00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series] 09:00.0 Network controller: Intel Corporation Centrino Advanced-N 6230 (rev 34) 0a:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5116 PCI Express Card Reader (rev 01) 10:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) 11:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

    Read the article

  • NVIDIA proprietary driver logging me to console instead of GUI

    - by Woozie
    Firstly i want to apologise for any mistakes, English is not my native language. My problem is I can't get NVIDIA proprietary drivers to work. I tried to install it on Ubuntu 12.04.1 32 and 64 bits, Ubuntu 12.10 Beta 2, Linux Mint 13 Cinnamon 64 bits and openSUSE 12.2 64 bits and the error code and symptoms (logging to tty1 instead of GUI logging, low-res bootscreen) are the same for all of these distros. Right, I didn't tell what's the error code. It appears on sudo startx. NVIDIA: could not open the device file /dev/nvidia0 (Input/output error). I know that's the common problem, but I tried to blacklist or even remove the noveau drivers, install NVIDIA driver from repo/from official script/in "Additional drivers", editing xorg.conf and using Xorg -configurate and nvidia-xconfig, actualizing the kernel and entire distro and many, many things that I don't remember. But the problem is even better: entire Cinnamon (Mint) is freezing during the work. I found the error code, which appears during the freeze: Oct 1 20:57:17 WoozieLaptop kernel: [ 308.120176] [drm] nouveau 0000:01:00.0: PFIFO_CACHE_ERROR - Ch 4/1 Mthd 0z0060 Data 0xbcef0201 My Xorg.0.log is here. It was made on Ubuntu 12.04.1 after installing NVIDIA drivers (obviously). inxi -G from Mint: Graphics: Card: NVIDIA GT216 [GeForce GT 240M] X.org: 1.11.3 drivers: (unloaded: nvidia) FAILED: nouveau,vesa,fbdev tty size: 80x25 Advanced Data: N/A for root out of X lspci -k | grep -A2 VGA from Mint: 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 240M] (rev a2) Subsystem: Lenovo Device 38ff Kernel driver in use: nvidia My hardware is: Lenovo IdeaPad Y550 Intel C2D T6600 NVIDIA GeForce GT 240M 4 GB of RAM Any help will be appreciated. This problem totally disabled my laptop from daily using. Cheers, Woozie

    Read the article

  • How to update Adobe's software unattendedly?

    - by jubel
    I would like to use unattended-upgrade to update the Adobe Reader, Flash Player and everything else of the Canonical partners. There fore, I added in /etc/apt/apt.conf.d/50unattended-upgrades Unattended-Upgrade::Allowed-Origins { "${distro_id} ${distro_codename}-security"; "${distro_id} ${distro_codename}-updates"; "Canonical ${distro_codename}"; // "${distro_id} ${distro_codename}-proposed"; // "${distro_id} ${distro_codename}-backports"; }; sudo unattended-upgrade --dry-run -d says Initial blacklisted packages: Starting unattended upgrades script Allowed origins are: ['o=Ubuntu,a=oneiric-security', 'o=Ubuntu,a=oneiric-updates', 'o=Canonical,a=oneiric'] Checking: acroread-common (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobe-flash-properties-gtk (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobe-flashplugin (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: adobereader-deu (["<Origin component:'partner' archive:'' origin:'' label:'' site:'archive.canonical.com' isTrusted:False>"]) Checking: handbrake-cli (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-stebbins-handbrake-snapshots' label:'HandBrake Snapshots' site:'ppa.launchpad.net' isTrusted:True>"]) Checking: handbrake-gtk (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-stebbins-handbrake-snapshots' label:'HandBrake Snapshots' site:'ppa.launchpad.net' isTrusted:True>"]) Checking: sopcast-player (["<Origin component:'main' archive:'oneiric' origin:'LP-PPA-ferramroberto-sopcast' label:'LffL Sopcast' site:'ppa.launchpad.net' isTrusted:True>"]) pkgs that look like they should be upgraded: Fetched 0 B in 0s (0 B/s) blacklist: [] InstCount=0 DelCount=0 BrokenCout=0 No packages found that can be upgraded unattended And it won't update. How can I update the third-party software automatically?

    Read the article

  • I have problem on 12.10 64bit with nvidia graphics driver opensource and proprietary ! Can't change resolution on 3d games

    - by digitalcrow
    I have problem with nvidia graphics driver opensource and proprietary ! Can't change resolution on 3d games and there's a bug there are no kernel sources installed and thus jockey can't install proprietary drivers. I can't change resolution while on games fullscreen. I tried to install proprietary driver and i couldn't plus i couldn't login to ubuntu it showed only the desktop photo no dash no nothing. -tried to install kernel sources and blacklist+remove Nouveau drivers and then installed the proprietary drivers i hope succesfully. -The problem is the same i can't change resolution on 3d games while on fullscreen. I've installed the sources and be able to install the proprietary nvidia drivers but the problem remains, look what i got in the output of a 3d game exited while i tried to change resolution: X Error of failed request: BadValue (integer parameter out of range for operation) Major opcode of failed request: 150 (XFree86-VidModeExtension) Minor opcode of failed request: 10 (XF86VidModeSwitchToMode) Value in failed request: 0x25b Serial number of failed request: 497 Current serial number in output stream: 499 I'm giving you more details about my system: i have an nvidia geforce gts 250 , 3,4 ghz quadcore amd phenom2 , 8gbytes of ram. The output of: sudo lshw -C display; lsb_release -a; uname -a Is the following: *-display description: VGA compatible controller product: G92 [GeForce GTS 250] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:ef00(size=128) memory:fb000000-fb01ffff No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.10 Release: 12.10 Codename: quantal Linux darkpc 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I like ubuntu's style and user interface but i hate the bad quality of work they do.

    Read the article

  • New mainboard with 890GX chipset disables lightdm, even when using old graphics card instead of onboard graphics, startx works (Xubuntu 12.04)

    - by user99250
    I am trying to migrate an installed Xubuntu 12.04 to a new mainbaord with 890GX chipset. The Chipset has a built-in Radeon HD 4290 graphics. The system boots, but X won't start. The most suspicious message in Xorg.0.log is "ddxSigGiveUp: Closing log". When searching for this message, I found some answers like "remove your xorg.conf" (but there is none on my system). Or bug reports for fglrx (but that's not installed on my system). Or NVidia-related questions ... Interestingly, "startx" succeeds in opening a basic XFCE session. Then, I tried to disable the onboard graphics in the BIOS setup and use the old PCIe graphics card (Radeon HD 5450). No change. I don't think I can just blacklist a module, because the graphics card and the onboard graphics are covered by the same module. At the moment, use the free radeon drivers, not the restricted fglrx driver. If possible, I would like to stay on the free driver for two reasons: The fglrx driver from the ubuntu packages fails to build the kernel module. In past, I had bad experiences with the fglrx driver and changing screen config with RandR. When I connect the harddisk and the graphics card to my old mainboard, everything works again. This means, I have not screwed up my system configuration wile installing and removing the fglrx drivers. When I ordered this mainboard, I thought the 890GX is old enough to be supported and if not, I could still use my graphics card as backup solution. But without even the backup soluton, I'm screwed ... Any ideas ? Thanks and Regards, Kubuntu-Man (now switched to Xubuntu)

    Read the article

  • Ask a DNS server what sites it hosts - and how to possibly prevent misuse

    - by Exit
    I've got a server which I host my company website as well as some of my clients. I noticed a domain which I created, but never used, was being attacked by a poke and hope hacker. I imagine that the hacker collected the domain from either hitting my DNS server and requesting what domains are hosted. So, in the interest of prevention and better server management, how would I ask my own DNS server (Linux CentOS 4) what sites are being hosted on it? Also, is there a way to prevent these types of attacks by hiding this information? I would assume that DNS servers would need to keep some information public, but I'm not sure if there is something that most hosts do to help prevent these bandwidth wasting poke and hope attacks. Thanks in advance.

    Read the article

  • Are there any differences between SQL Server and MySQL when it comes to preventing SQL injection?

    - by Derek Adair
    I am used to developing in PHP/MySQL and have no experience developing with SQL Server. I've skimmed over the PHP MSSQL documentation and it looks similar to MySQLi in some of the methods I read about. For example, with MySQL I utilize the function mysql_real_excape_string(). Is there a similar function with PHP/SQL Server? What steps do I need to take in order to protect against SQL injection with SQL Server? What are the differences between SQL Server and MySQL pertaining to SQL injection prevention? also - is this post accurate? is the escape string character for SQL Server a single quote?

    Read the article

  • Using C preprocessor to construct a string literal for scanf?

    - by Brett
    I'm attempting to create an sscanf string literal to aid in buffer overrun prevention in C99. The goal is something like: #define MAX_ARG_LEN 16 char arg[MAX_ARG_LEN] = ""; if (sscanf(arg, "%"(MAX_ARG_LEN-1)"X", &input) > 0) The obvious "manual" solution is something like: #define MAX_ARG_LEN 16 #define MAX_ARG_CHARS "15" char arg[MAX_ARG_LEN] = ""; if (sscanf(arg, "%"MAX_ARG_CHARS"X", &input) > 0) However, I would prefer something to automatically generate "%15X" given a buffer size of 16. This link is almost works for my application: http://stackoverflow.com/questions/240353/convert-a-preprocessor-token-to-a-string but it does not handle the -1. Suggestions?

    Read the article

  • SQL server 2005 remote connection problem, cannot solve it help please thank you

    - by user287745
    note:- if this question does not fit this site please do not just close it but also redirect the question to the fitting sister site, thank you" the steps taken and the error are mentioned please help, i am stuck here! installed sql server 2005 express on both computers installed sql server management studio express on both computers ran each management studio and connect to instance sqlserver using windows authentication ( one computer connection example "A-63A9D4D7E7834\SQLEXPRESS" ) created a database in the databases named as "test1" created a few tables with data saved and exit. did everything what this site says " How to configure SQL Server 2005 to allow remote connections" [add h t t p here as spam prevention] ://support.microsoft.com/kb/914277/en-us" but i have just disable the firewalls completely :turn off connecting to A-63A9D4D7E7834 started "SQL Server Management Studio Express" on computer A-63A9D4D7E7834 sever name: "ALL-E425BE6C41D\SQLEXPRESS" authentication: "windows authentication" and CONNECT I GET THE FOLLOWING ERROR Cannot connect to ALL-E425BE6C41D\SQLEXPRESS. ADDITIONAL INFORMATION: Login failed for user 'ALL-E425BE6C41D\Guest'. (Microsoft SQL Server, Error: 18456) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=18456&LinkId=20476 BUTTONS: OK HELP

    Read the article

  • Another answer to the CAPTCHA problem?

    - by Xeoncross
    Most sites at least employ server access log checking and banning along with some kind of bot prevention measure like a CAPTCHA (those messed-up text images). The problem with CAPTCHAs is that they poss a threat to the user experience. Luckily they now come with user friendly features like refresh and audio versions. Anyway, like linux vs windows, it isn't worth the time of a spammer to customize and/or build a script to handle a custom CAPTCHA example that only pertains to one site. Therefore, I was wondering if there might be better ways to handle the whole CAPTCHA thing. In A Better CAPTCHA Peter Bromberg mentions that one way would be to convert the image to HTML and display it embedded in the page. On http://shiflett.org/ Chris simply asks users to type his name into an input. Examples like this are ways to simplifying the CAPTCHA experience while decreasing the value for spammers. Does anyone know of more good examples I could use or see any problem with the embedded image idea?

    Read the article

  • Are there any differences between MSSQL and MySQL when it comes to preventing SQL injection?

    - by Derek Adair
    I am used to developing in PHP/MySQL and have no experience developing with MSSQL. I've skimmed over the PHP MSSQL documentation and it looks similar to MySQLi in some of the methods I read about. For example, with MySQL I utilize the function mysql_real_excape_string(). Is there a similar function with PHP/MSSQL? What steps do I need to take in order to protect against SQL injection with MSSQL? What are the differences between MSSQL and MySQL pertaining to SQL injection prevention?

    Read the article

  • SQL server 2055 remote connection problem, cannot solve it help please thank you

    - by user287745
    note:- if this question does not fit this site please do not just close it but also redirect the question to the fitting sister site, thank you" the steps taken and the error are mentioned please help, i am stuck here! installed sql server 2005 express on both computers installed sql server management studio express on both computers ran each management studio and connect to instance sqlserver using windows authentication ( one computer connection example "A-63A9D4D7E7834\SQLEXPRESS" ) created a database in the databases named as "test1" created a few tables with data saved and exit. did everything what this site says " How to configure SQL Server 2005 to allow remote connections" [add h t t p here as spam prevention] ://support.microsoft.com/kb/914277/en-us" but i have just disable the firewalls completely :turn off connecting to A-63A9D4D7E7834 started "SQL Server Management Studio Express" on computer A-63A9D4D7E7834 sever name: "ALL-E425BE6C41D\SQLEXPRESS" authentication: "windows authentication" and CONNECT I GET THE FOLLOWING ERROR Cannot connect to ALL-E425BE6C41D\SQLEXPRESS. ADDITIONAL INFORMATION: Login failed for user 'ALL-E425BE6C41D\Guest'. (Microsoft SQL Server, Error: 18456) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=18456&LinkId=20476 BUTTONS: OK HELP

    Read the article

  • I still can't ask the question I want to ask! [closed]

    - by Dennis
    Possible Duplicate: Unable to post question despite having no hyperlinks I'm trying to leave a real question but I keep getting this error: We're sorry, but as a spam prevention mechanism, new users can only post a maximum of one hyperlink. Earn 10 reputation to post more hyperlinks. I have removed all the hyper links in the question but I'm still getting the error. Is there someone I can email the code to so we can figure out what the problem is? And I really didn't appreciate the smart ass comment left by whom ever close my last question.

    Read the article

  • html5media & flowplayer wmode issues...

    - by minusidea
    I'm working on our new homepage and need to implement a solution that will run a video across iphone/ipad and the standard web browsers. I found a pretty decent solution with html5media - http://code.google.com/p/html5media/ but ran across an issue with a jquery dropdown falling behind the the swf object (this only happens on FF & IE - works fine on Safari & Chrome because it's loading mp4 instead of a swf object). I know the issue is the wmode setting but can not for the life of me figure out where to set it in the html5media (http://html5media.googlecode.com/svn/trunk/src/html5media.min.js). I'm hoping someone can help me or possibly give me a better solution of implementing the video. You can see the development page at idssite(dot)com/development/index.php - Sorry I can't link I'm being stopped by the spam prevention mechanism. Thanks

    Read the article

  • Why does Google append while(1); in front of their JSON responses?

    - by Andrew Koester
    This is something I've always been curious about, is exactly why Google appends while(1); in front of their (private) JSON responses. For example, here's a response while turning a calendar on and off in Google Calendar: while(1);[['u',[['smsSentFlag','false'],['hideInvitations','false'],['remindOnRespondedEventsOnly','true'],['hideInvitations_remindOnRespondedEventsOnly','false_true'],['Calendar ID stripped for privacy','false'],['smsVerifiedFlag','true']]]] I would assume this is to prevent people from doing an eval() on it, but all you'd really have to do is replace the while and then you'd be set. I would assume eval prevention is to make sure people write safe JSON parsing code. I've seen this used in a couple other places, too, but a lot more so with Google (Mail, Calendar, Contacts, etc.) Strangely enough, Google Docs starts with &&&START&&& instead, and Google Contacts seems to start with while(1); &&&START&&&. Does anyone know what's going on here?

    Read the article

  • Preventing SQL injecting in a database class

    - by Josh
    I'm building a database class and thought it'd be a good idea to incorporate some form of SQL injection prevention (duh!). Here's the method that runs a database query: class DB { var $db_host = 'localhost'; var $db_user = 'root'; var $db_passwd = ''; var $db_name = 'whatever'; function query($sql) { $this->result = mysql_query($sql, $this->link); if(!$this->result) { $this->error(mysql_error()); } else { return $this->result; } } } There's more in the class than that but I'm cutting it down just for this. The problem I'm facing is if I just use mysql_real_escape_string($sql, $this->link); then it escapes the entire query and leads to a SQL syntax error. How can I dynamically find the variables that need to be escaped? I want to avoid using mysql_real_escape_string() in my main code blocks, i'd rather have it in a function. Thanks.

    Read the article

  • Are you cashing in on the MVP complimentary subscriptions ?

    - by Tarun Arora
    The two most asked questions in the Microsoft technology communities around the Microsoft MVP program are, 1. How do I become a Microsoft MVP? 2. What benefits do I get as an MVP? The answer to the first question has been well answered here. In this blog post, I’ll try and answer the second question.           Please find a comprehensive list of Not for Resale personal subscriptions of various products that Microsoft MVP’s are eligible for Product Description Details JetBrains Resharper, dotTrace, dotCover & WebStorm  https://www.jetbrains.com/resharper/buy/mvp.html RedGate Sql server development, database administration, .net development, azure development (merged with Cerebrata), mySQL development, Oracle development http://www.red-gate.com/community/mvp-program Pluralsight Pluralsight on demand training http://blog.pluralsight.com/2011/02/28/pluralsight-for-mvp/ Cerebrata Cloud storage studio and Azure Diagnostic Manager (part of redgate now) https://www.cerebrata.com/Offers/mvp.aspx Telerik Telerik Ultimate collection & Telerik TeamPulse http://blogs.telerik.com/blogs/posts/11-03-01/telerik-gift-for-microsoft-mvps.aspx Developer Express DevEx controls http://www.devexpress.com/Home/Community/mvp.xml InnerWorking 600 hours of .net training catalogue http://www.innerworkings.com/mvp Typemock Typemock Isolator, Typemock Isolator for Sharepoint developers, Typemock Isolator for web developers, TestDriven.NET http://www.typemock.com/mvp SpeakFlow A suite of tools for creating, managing, and delivering non-linear presentations http://www.speakflow.com/ TechSmith Camtasia Studio, SnagIt, screen cast http://www.techsmith.com/camtasia.html Altova Altova XML spy http://www.altova.com/xml-editor/ Visual SVN VisualSVN Subversion integration plug-in for Visual Studio http://www.visualsvn.com/visualsvn/purchase/mvp/ PreEmptive Solution Professional PreEmptive Analytics, Dotfuscator http://www.preemptive.com/landing/mvp Armadillo Armadillo Adaptive Bug Prevention http://www.armadilloverdrive.com/ IS Decisions NFR license to Userlock, RemoteExec, FileAudit & WinReporter http://www.isdecisions.com/download/mvp-mct-program.htm Idera SQL tools http://www.idera.com/Content/Home.aspx West Wind Help Builder Help builder solution http://www.west-wind.com/weblog/posts/2005/Mar/09/Are-you-a-Microsoft-MVP-Get-a-FREE-copy-of-West-Wind-Html-Help-Builder Bamboo Sharepoint tools http://community.bamboosolutions.com/blogs/partner-advantage-program/archive/2008/08/01/partner-advantage-program-mvp.aspx Nitriq Nitriq code analysis http://blog.nitriq.com/FreeLicensesForMicrosoftMVPs.aspx ByteScout Components, Libraries and Developer Tools http://bytescout.com/buy/purchase_nfr_for_mvp.html YourKit Java and .net Profiler http://yourkit.com/.net/profiler/index.jsp Aspose .NET components http://www.aspose.com/corporate/community/2012_05_08_nfr-licenses-for-community-leaders.aspx Apart from google bing fu; stackoverflow and breathtech were a great help in compiling the above list. If you know of any other benefits, offers or complimentary subscriptions on offer for MVPs not cover in the list above, please add to the comment thread and I’ll have it updated in the list. Enjoy

    Read the article

  • Walking to the North Pole to raise money to protect children from cruelty.

    - by jessica.ebbelaar
    Hi, my name is Luca. I joined Oracle in 2005 and I am currently working as a Dell EMEA Channel Manager UK, Ireland and Iberia and I am responsible for the Oracle Dell relationship for the above 3 countries. On the 31st of March 2011 I will set out to complete the ultimate challenge. I will walk and ski across the frozen Arctic to the Top of The World: the GEOGRAPHIC North Pole. While dragging all my supplies over 60 Nautical miles of moving sea ice, in temperatures as low as minus 30 degrees Celsius. I will spend 8 to 10 days preparing, working, living and travelling to the North Pole to 90 degree north. In November I spent a full week of training for this trip.( watch my video). This gave me the opportunity to meet the rest of the team, testing all the gear and carrying an 18inch tyre around the country side for 8 hours per day. I am honored to embark this challenging journey to support the National Society for the Prevention of Cruelty to Children (NSPCC). The NSPCC helped more than 750,000 young people to speak out for the first time about abuse they had suffered. I am a firm believer that in order to build a stronger, healthier and wiser society we need to support and help future generations from the beginning of their life journey. This is why cruelty to children must stop. FULL STOP.   Through Virgin Money Giving, you can sponsor me and donations will be quickly processed and passed to NSPCC. Virgin Money Giving is a non-profit organization and will claim gift aid on a charity's behalf where the donor is eligible for this. If you are a UK tax payer please don't forget to select Gift Aid. Gift Aid is great because it means charities get extra money added to their donations at no extra cost to the donor. For every £1 donated, the charity currently receives £1.28 when you add Gift Aid. Anyone who would like to find out more can visit my Facebook page ‘Luca North Pole charity fundraising trip’ I really appreciate all your support and thank you for supporting the NSPCC. Tags van Technorati: Channel Manager,challenge,Arctic,North Pole,NSPCC,cruelty to children,Luca North Pole charity fundraising trip. If fou have any questions related to this article contact [email protected].

    Read the article

  • SOLVED Install MythTV & 11.10 on Lenovo S12 (Intel atom) with wireless

    - by keepitsimpleengineer
    This is how I installed Ubuntu 11.10 and MythTV client on my Lenovo S12 (Intel Atom) laptop and use it using WiFi (see additional notes at end). I did this because the upgrade from 11.04 bricked the laptop. Note that the partitions on the Lenovo standard disk were already in place for this installation. Also note that my LAN is setup for fixed IP addresses. Downloaded and burned 11.10 x86 Desktop Ubuntu CD Connected the power supply cord, LAN wire and the external DVD USB drive. Ran Windows XP and made sure performance level "Performance" was set and "Wireless" was enabled. Booted S12 from CD Disabled Networking from icon on upper left panel icon Edited Connections… "Wired connection 1" ? Set IP address, accepted default netmask and set gateway. Also set DNS server. Good idea to check "Connection Information" here to verify everything's O.K. Selected Install Ubuntu from the initial "Install" window Verified the three items were checked (required disk space available, plugged into a power source, & connected to the Internet) Selected Download updates while installing and third party software. Hit Continue… At wireless selected don't want to connect…WiFi…now. Continue… At Installation type, selected Something else. Continue… At partition tale, selected the ext4 Linux partition, set the mount point as "/", and marked for formatting. Here I selected the main disk (/sda) for installing the boot manager. Continue… Selected or verified my Time zone. Continue… Selected my keyboard layout. Continue… Filled in the who are you fields. Make sure password is required to sign in is checked. Continue… Chose a picture. Continue… I selected import no accounts. Continue… Wait as the Install creeps along. If your screen goes blank, tap the space bar ? apparently the screen saver/power plan does this. There are several progress bars. The longest was "Installing system", and it was the next to the last one. Installation Complete window appears, Restart Now… Wait as it stops, The screen blanks then the message "…remove…media…close tray…press enter" I just unplugged the USB DVD and hit enter… It was disheartening but the screen turned Ubuntu Purple-beige and nothing happened, so I help down the power key until it shut down, the pressed it again and the Grub Boot screen appeared. Select Ubuntu… 25.The screen went blank with the little flashing underscore cursor on it and the disk light would occasionally flash. I hit the enter key and eventuality Ubuntu started. After a somewhat long time the unity desktop appeared. 11.10, unlike earlier versions, retains the connection information. Check this by checking the network icon on the upper left applet panel. Here the touch-pad·mouse quit working and I had to reboot. It takes and extremely long time to boot, sometimes requiring several power off/ power on (cold boot). You can try to get the default network manager to work, but it might not, it didn't on mine for WiFi. Thanks to: Chris at URL here's what to do… disconnect your wired Internet connection. input your wireless information into network manager open a terminal (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "terminal". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. click to open a terminal, and type in: sudo rmmod acer_wmi && echo "blacklist acer_wmi" >> /etc/modprobe.d/blacklist.conf and hit enter. type in your password as asked. if you have correctly entered your WiFi information and you are near your AP, you should connect immediately if not, see the URL above ? you might need to replace "network manager" with "wicd" ? I did with 11.04. Update the new 11.10, in the upper left panel applet weird·gear icon is menu with a line about updating. It's the new way to invoke Update Manager. Your lenovo S12 (intel atom) should now run the new unity Ubuntu. Point your elbow at the ceiling and pat yourself on the back. Installing Mythbuntu Client 24.1 Open mythbuntu.org/repos (I urge you not to directly use Ubuntu Software Center for this) Install Mythbuntu Repos Save the file (in ~/Downloads, the default) Run the file ? it will update your repositories so that you will get the proper installation sources ? it will start Ubuntu Software Center to do this ? Click Install… You will need your password. Debconf window will open, select by making sure check mark is in the little box "Would you like to activate…". Forward… Which version? At the time of writing the current "Stable" version was 24.1, select 0.24.x… Forward… Read the message, then forward… Delete the downloaded file. Install synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "synaptic". Click on the synaptic icon. Ubuntu Software Center will open and allow you to install synaptic package manager. Open Synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "Synaptic". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. Run synaptic, read the intro, and close the intro window. Type in mythbuntu-control-centre in the Quick filter text box, and then select it "Mark for installation" by clicking on the box next to it's name. Marvel at the additional to be installed items, then select "?Mark"… At the top of the synaptic window click on the "? Apply" button. Marvel at the amount of stuff to be installed, the click on "Apply". When finished, close finished window and synaptic. Open mythbuntu-control-centre (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythbuntu". Might be a good idea to drag and drop the mythbuntu-control-centre icon to the terminal, it's easy to get rid of later. You can now configure and install the frontend. Go down the icon totem on the right side of the window and click as needed… System roles. ? No Backend, Desktop Frontend, and Ubuntu Desktop. Apply… & Apply changes… & Password… MySQL Configuration ? from backend ? Setup General Alt-N(ext) Alt-N(ext) Stetting Access Setup PIN code: ~~~~ Input Security key and click "Test Connection", if ?, then Apply… & Apply… {note: for some inexplicable reason, control centre hung on this, but when I restarted it, it was set properly} Graphics drivers, When I did this, only the Broadcom wireless driver showed up. I closed without doing anything. Services. I enabled SSH & Samba. Apply… & Apply… Repositories. Asked & Answered. MythExport. Pass, I believe it requires backend on the same system. Proprietary Codec Support. Check to enable, Apply… & Apply… System Updates. No action necessary, will be a part of the Ubuntu update mechanism. Themes and Artwork. For themes, I selected Enable/Update all. Apply… & Apply… Infrared & Startup behavior and Plugins. Defer until you know more. Close software centre. Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Incorrect Group Membership. Fix this by clicking "Yes"… Log out/end. Do this by clicking "Yes"… For my Lenovo S12, I had to manually restart Ubuntu - and still with the very long restart…/no start/cold boot/reboot/pressing the shift key required Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Will open with Select country & language. Do so. then get message with "No", hit "Ok" and arrive at the data base Configuration 1/2 screen. You will need your brackend password, from backend ? Setup General Database Configuration 1/2 Password:~? Enter this Hit Alt-n to go to the next page. Select "Use custom id…", then enter a custom ID, I use the machine's name. Hit finish, and MythTV should start up with all default settings. For the lenovo S12, the first thing you want to do is to set Playback profiles to "Normal". From Setup TV Settings Playback Alt-N(ext) Alt-N(ext) Playback Profiles (3/8) : Change Current Video Playback Profile to "Normal". You can fiddle with this setting later. For the lenovo S12, the second thing is to get the sound going. From Setup General Alt-N(ext) Alt-N(ext) Alt-N(ext) Audio System: The top of the screen is a button title "Scan for audio devices", move the highlight there and press the Space bar. Then Tab down to Audio Output Device: and left-right arrow until "ALSA:hw:Card=Intel,DEV=0" is selected. Then Alt-N(ext) until "Finish". Now you should have sound. You should now have MythTV working nicely on the Lenovo S12 Notes about wireless: Running Lenovo S12 on wireless is demanding on both power and WiFi connection. Best results will be obtained when running on power and wired connection. I run my S12 on wireless, actually two serial connections with two access points, something that is not easy to achieve. Here Mythbuntu client-server (in den) <? wireless link 1 <?office LAN? wireless link 2 <? Lenovo S12 Ubuntu 11.10 The office LAN is fixed IP behind an Untangle firewall router. There is another MythTV client on Ubuntu 10.10 computer in the office (which has always worked well). ProblemMythbuntu\Win7 client hangs with frozen frames, short segment of audio repeating. Hardware Rosewill RNX-G300EX IEEE 802.11b/g PCI Wireless Card on client-server 2 Linksys WRT54GL wireless broadband routers on LAN for link1 and link 2 WRT54GL FirmwareDD-WRT v24-sp2(07/22/09) voip set up to act as an access point. Note? many people advised this was an unworkable scheme, and in probably most cases it will be. Solution? Set up DD-WRT with the following Wireless settings… Basic Channel: Different fixed channels at least 4 difference, I use 6 & 11 Basic Sensitivity Range (ACK timing): 50 MAC filter use filter: Enable, Selected Permit only clients listed to access… Requires adding MAC addresses in "Edit MAC Filter List" This causes the 54GL's to ignore any but the listed MAC address, down side, no "guest" capability. Advanced Basic rate: All Advanced CTS Protection Mode: Off Advanced Frame Burst: Enable Advanced Max associate clients: 4 for client link 2, 1 for client-server link 1 Advanced AP isolation: Enable Advanced Preamble: Short Advanced Afterburner: On Advanced Wireless GUI access: Off Advanced WMM support: Off Other settings: default for supplied firmware. Why I suspect this worked? The 54GL Access Points's with the firmware's setting are set to handle a multiple client, wide area situation. With these mods I reconfigured them for a small area, few client situation, disabling Advanced WMM probably the most important. In addition, the client mythtv when used all other users of its access point are turned off except for a Skype phone. Also, the client-server is set up to allow other connections though it's LAN connection, and these are used to connect the TV and disc players, not used when client is being used.

    Read the article

  • Issue 15: Oracle Exadata Marketing Campaigns

    - by rituchhibber
         PARTNER FOCUS Oracle ExadataMarketing Campaign Steve McNickleVP Europe, cVidya Steve McNickle is VP Europe for cVidya, an innovative provider of revenue intelligence solutions for telecom, media and entertainment service providers including AT&T, BT, Deutsche Telecom and Vodafone. The company's product portfolio helps operators and service providers maximise margins, improve customer experience and optimise ecosystem relationships through revenue assurance, fraud and security management, sales performance management, pricing analytics, and inter-carrier services. cVidya has partnered with Oracle for more than a decade. RESOURCES -- Oracle PartnerNetwork (OPN) Oracle Exastack Program Oracle Exastack Optimized Oracle Exastack Labs and Enablement Resources Oracle Engineered Systems Oracle Communications cVidya SUBSCRIBE FEEDBACK PREVIOUS ISSUES Are you ready for Oracle OpenWorld this October? -- -- Please could you tell us a little about cVidya's partnering history with Oracle, and expand on your Oracle Exastack accreditations? "cVidya was established just over ten years ago and we've had a strong relationship with Oracle almost since the very beginning. Through our Revenue Intelligence work with some of the world's largest service providers we collect tremendous amounts of information, amounting to billions of records per day. We help our clients to collect, store and analyse that data to ensure that their end customers are getting the best levels of service, are billed correctly, and are happy that they are on the correct price plan. We have been an Oracle Gold level partner for seven years, and crucially just two months ago we were also accredited as Oracle Exastack Optimized for MoneyMap, our core Revenue Assurance solution. Very soon we also expect to be Oracle Exastack Optimized DRMap, our Data Retention solution." What unique capabilities and customer benefits does Oracle Exastack add to your applications? "Oracle Exastack enables us to deliver radical benefits to our customers. A typical mobile operator in the UK might handle between 500 million and two billion call data record details daily. Each transaction needs to be validated, billed correctly and fraud checked. Because of the enormous volumes involved, our clients demand scalable infrastructure that allows them to efficiently acquire, store and process all that data within controlled cost, space and environmental constraints. We have proved that the Oracle Exadata system can process data up to seven times faster and load it as much as 20 times faster than other standard best-of-breed server approaches. With the Oracle Exadata Database Machine they can reduce their datacentre equipment from say, the six or seven cabinets that they needed in the past, down to just one. This dramatic simplification delivers incredible value to the customer by cutting down enormously on all of their significant cost, space, energy, cooling and maintenance overheads." "The Oracle Exastack Program has given our clients the ability to switch their focus from reactive to proactive. Traditionally they may have spent 80 percent of their day processing, and just 20 percent enabling end customers to see advanced analytics, and avoiding issues before they occur. With our solutions and Oracle Exadata they can now switch that balance around entirely, resulting not only in reduced revenue leakage, but a far higher focus on proactive leakage prevention. How has the Oracle Exastack Program transformed your customer business? "We can already see the impact. Oracle solutions allow our delivery teams to achieve successful deployments, happy customers and self-satisfaction, and the power of Oracle's Exa solutions is easy to measure in terms of their transformational ability. We gained our first sale into a major European telco by demonstrating the major performance gains that would transform their business. Clients can measure the ease of organisational change, the early prevention of business issues, the reduction in manpower required to provide protection and coverage across all their products and services, plus of course end customer satisfaction. If customers know that that service is provided accurately and that their bills are calculated correctly, then over time this satisfaction can be attributed to revenue intelligence and the underlying systems which provide it. Combine this with the further integration we have with the other layers of the Oracle stack, including the telecommunications offerings such as NCC, OCDM and BRM, and the result is even greater customer value—not to mention the increased speed to market and the reduced project risk." What does the Oracle Exastack community bring to cVidya, both in terms of general benefits, and also tangible new opportunities and partnerships? "A great deal. We have participated in the Oracle Exastack community heavily over the past year, and have had lots of meetings with Oracle and our peers around the globe. It brings us into contact with like-minded, innovative partners, who like us are not happy to just stand still and want to take fresh technology to their customer base in order to gain enhanced value. We identified three new partnerships in each of two recent meetings, and hope these will open up new opportunities, not only in areas that exactly match where we operate today, but also in some new associative areas that will expand our reach into new business sectors. Notably, thanks to the Exastack community we were invited on stage at last year's Oracle OpenWorld conference. Appearing so publically with Oracle senior VP Judson Althoff elevated awareness and visibility of cVidya and has enabled us to participate in a number of other events with Oracle over the past eight months. We've been involved in speaking opportunities, forums and exhibitions, providing us with invaluable opportunities that we wouldn't otherwise have got close to." How has Exastack differentiated cVidya as an ISV, and helped you to evolve your business to the next level? "When we are selling to our core customer base of Tier 1 telecommunications providers, we know that they want more than just software. They want an enduring partnership that will last many years, they want innovation, and a forward thinking partner who knows how to guide them on where they need to be to meet market demand three, five or seven years down the line. Membership of respected global bodies, such as the Telemanagement Forum enables us to lead standard adherence in our area of business, giving us a lot of credibility, but Oracle is also involved in this forum with its own telecommunications portfolio, strengthening our position still further. When we approach CEOs, CTOs and CIOs at the very largest Tier 1 operators, not only can we easily show them that our technology is fantastic, we can also talk about our strong partnership with Oracle, and our joint embracing of today's standards and tomorrow's innovation." Where would you like cVidya to be in one year's time? "We want to get all of our relevant products Oracle Exastack Optimized. Our MoneyMap Revenue Assurance solution is already Exastack Optimised, our DRMAP Data Retention Solution should be Exastack Optimised within the next month, and our FraudView Fraud Management solution within the next two to three months. We'd then like to extend our Oracle accreditation out to include other members of the Oracle Engineered Systems family. We are moving into the 'Big Data' space, and so we're obviously very keen to work closely with Oracle to conduct pilots, map new technologies onto Oracle Big Data platforms, and embrace and measure the benefits of other Oracle systems, namely Oracle Exalogic Elastic Cloud, the Oracle Exalytics In-Memory Machine and the Oracle SPARC SuperCluster. We would also like to examine how the Oracle Database Appliance might benefit our Tier 2 service provider customers. Finally, we'd also like to continue working with the Oracle Communications Global Business Unit (CGBU), furthering our integration with Oracle billing products so that we are able to quickly deploy fraud solutions into Oracle's Engineered System stack, give operational benefits to our clients that are pre-integrated, more cost-effective, and can be rapidly deployed rapidly and producing benefits in three months, not nine months." Chris Baker ,Senior Vice President, Oracle Worldwide ISV-OEM-Java Sales Chris Baker is the Global Head of ISV/OEM Sales responsible for working with ISV/OEM partners to maximise Oracle's business through those partners, whilst maximising those partners' business to their end users. Chris works with partners, customers, innovators, investors and employees to develop innovative business solutions using Oracle products, services and skills. Firstly, could you please explain Oracle's current strategy for ISV partners, globally and in EMEA? "Oracle customers use independent software vendor (ISV) applications to run their businesses. They use them to generate revenue and to fulfil obligations to their own customers. Our strategy is very straight-forward. We want all of our ISV partners and OEMs to concentrate on the things that they do the best – building applications to meet the unique industry and functional requirements of their customer. We want to ensure that we deliver a best in class application platform so the ISV is free to concentrate their effort on their application functionality and user experience We invest over four billion dollars in research and development every year, and we want our ISVs to benefit from all of that investment in operating systems, virtualisation, databases, middleware, engineered systems, and other hardware. By doing this, we help them to reduce their costs, gain more consistency and agility for quicker implementations, and also rapidly differentiate themselves from other application vendors. It's all about simplification because we believe that around 25 to 30 percent of the development costs incurred by many ISVs are caused by customising infrastructure and have nothing to do with their applications. Our strategy is to enable our ISV partners to standardise their application platform using engineered architecture, so they can write once to the Oracle stack and deploy seamlessly in the cloud, on-premise, or in hybrid deployments. It's really important that architecture is the same in order to keep cost and time overheads at a minimum, so we provide standardisation and an environment that enables our ISVs to concentrate on the core business that makes them the most money and brings them success." How do you believe this strategy is helping the ISVs to work hand-in-hand with Oracle to ensure that end customers get the industry-leading solutions that they need? "We work with our ISVs not just to help them be successful, but also to help them market themselves. We have something called the 'Oracle Exastack Ready Program', which enables ISVs to publicise themselves as 'Ready' to run the core software platforms that run on Oracle's engineered systems including Exadata and Exalogic. So, for example, they can become 'Database Ready' which means that they use the latest version of Oracle Database and therefore can run their application without modification on Exadata or the Oracle Database Appliance. Alternatively, they can become WebLogic Ready, Oracle Linux Ready and Oracle Solaris Ready which means they run on the latest release and therefore can run their application, with no new porting work, on Oracle Exalogic. Those 'Ready' logos are important in helping ISVs advertise to their customers that they are using the latest technologies which have been fully tested. We now also have Exadata Ready and Exalogic Ready programmes which allow ISVs to promote the certification of their applications on these platforms. This highlights these partners to Oracle customers as having solutions that run fluently on the Oracle Exadata Database Machine, the Oracle Exalogic Elastic Cloud or one of our other engineered systems. This makes it easy for customers to identify solutions and provides ISVs with an avenue to connect with Oracle customers who are rapidly adopting engineered systems. We have also taken this programme to the next level in the shape of 'Oracle Exastack Optimized' for partners whose applications run best on the Oracle stack and have invested the time to fully optimise application performance. We ensure that Exastack Optimized partner status is promoted and supported by press releases, and we help our ISVs go to market and differentiate themselves through the use our technology and the standardisation it delivers. To date we have had several hundred organisations successfully work through our Exastack Optimized programme." How does Oracle's strategy of offering pre-integrated open platform software and hardware allow ISVs to bring their products to market more quickly? "One of the problems for many ISVs is that they have to think very carefully about the technology on which their solutions will be deployed, particularly in the cloud or hosted environments. They have to think hard about how they secure these environments, whether the concern is, for example, middleware, identity management, or securing personal data. If they don't use the technology that we build-in to our products to help them to fulfil these roles, they then have to build it themselves. This takes time, requires testing, and must be maintained. By taking advantage of our technology, partners will now know that they have a standard platform. They will know that they can confidently talk about implementation being the same every time they do it. Very large ISV applications could once take a year or two to be implemented at an on-premise environment. But it wasn't just the configuration of the application that took the time, it was actually the infrastructure - the different hardware configurations, operating systems and configurations of databases and middleware. Now we strongly believe that it's all about standardisation and repeatability. It's about making sure that our partners can do it once and are then able to roll it out many different times using standard componentry." What actions would you recommend for existing ISV partners that are looking to do more business with Oracle and its customer base, not only to maximise benefits, but also to maximise partner relationships? "My team, around the world and in the EMEA region, is available and ready to talk to any of our ISVs and to explore the possibilities together. We run programmes like 'Excite' and 'Insight' to help us to understand how we can help ISVs with architecture and widen their environments. But we also want to work with, and look at, new opportunities - for example, the Machine-to-Machine (M2M) market or 'The Internet of Things'. Over the next few years, many millions, indeed billions of devices will be collecting massive amounts of data and communicating it back to the central systems where ISVs will be running their applications. The only way that our partners will be able to provide a single vendor 'end-to-end' solution is to use Oracle integrated systems at the back end and Java on the 'smart' devices collecting the data – a complete solution from device to data centre. So there are huge opportunities to work closely with our ISVs, using Oracle's complete M2M platform, to provide the infrastructure that enables them to extract maximum value from the data collected. If any partners don't know where to start or who to contact, then they can contact me directly at [email protected] or indeed any of our teams across the EMEA region. We want to work with ISVs to help them to be as successful as they possibly can through simplification and speed to market, and we also want all of the top ISVs in the world based on Oracle." What opportunities are immediately opened to new ISV partners joining the OPN? "As you know OPN is very, very important. New members will discover a huge amount of content that instantly becomes accessible to them. They can access a wealth of no-cost training and enablement materials to build their expertise in Oracle technology. They can download Oracle software and use it for development projects. They can help themselves become more competent by becoming part of a true community and uncovering new opportunities by working with Oracle and their peers in the Oracle Partner Network. As well as publishing massive amounts of information on OPN, we also hold our global Oracle OpenWorld event, at which partners play a huge role. This takes place at the end of September and the beginning of October in San Francisco. Attending ISV partners have an unrivalled opportunity to contribute to elements such as the OpenWorld / OPN Exchange, at which they can talk to other partners and really begin thinking about how they can move their businesses on and play key roles in a very large ecosystem which revolves around technology and standardisation." Finally, are there any other messages that you would like to share with the Oracle ISV community? "The crucial message that I always like to reinforce is architecture, architecture and architecture! The key opportunities that ISVs have today revolve around standardising their architectures so that they can confidently think: “I will I be able to do exactly the same thing whenever a customer is looking to deploy on-premise, hosted or in the cloud”. The right architecture is critical to being competitive and to really start changing the game. We want to help our ISV partners to do just that; to establish standard architecture and to seize the opportunities it opens up for them. New market opportunities like M2M are enormous - just look at how many devices are all around you right now. We can help our partners to interface with these devices more effectively while thinking about their entire ecosystem, rather than just the piece that they have traditionally focused upon. With standardised architecture, we can help people dramatically improve their speed, reach, agility and delivery of enhanced customer satisfaction and value all the way from the Java side to their centralised systems. All Oracle ISV partners must take advantage of these opportunities, which is why Oracle will continue to invest in and support them." -- Gergely Strbik is Oracle Hardware and Software Product Manager for Avnet in Hungary. Avnet Technology Solutions is an OracleValue Added Distributor focused on the development of the existing Oracle channel. This includes the recruitment and enablement of Oracle partners as well as driving deeper adoption of Oracle's technology and application products within the IT channel. "The main business benefits of ODA for our customers and partners are scalability, flexibility, a great price point for the high performance delivered, and the easily configurable embedded Linux operating system. People welcome a lower point of entry and the ability to grow capacity on demand as their business expands." "Marketing and selling the ODA requires another way of thinking because it is an appliance. We have to transform the ways in which our partners and customers think from buying hardware and software independently to buying complete solutions. Successful early adopters and satisfied customer reactions will certainly help us to sell the ODA. We will have more experience with the product after the first deliveries and installations—end users need to see the power and benefits for themselves." "Our typical ODA customers will be those looking for complete solutions from a single reseller partner who is also able to manage the appliance. They will have enjoyed using Oracle Database but now want a new product that is able to unlock new levels of performance. A higher proportion of potential customers will come from our existing Oracle base, with around 30% from new business, but we intend to evangelise the ODA on the market to see how we can change this balance as all our customers adjust to the concept of 'Hardware and Software, Engineered to Work Together'. -- Back to the welcome page

    Read the article

  • New hidden parameters in Oracle 11.2

    - by Mike Dietrich
    We really welcome every external review of our slides. And also recommendations from customers visiting our workshops. So it happened to me more than a week ago that Marco Patzwahl, the owner of MuniqSoft GmbH, had a very lengthy train ride in Germany (as the engine drivers go on strike this week it could have become even worse) and nothing better to do then reviewing our slide set. And he had plenty of recommendations. Besides that he pointed us to something at least I was not aware of and added it to the slides: In patch set 11.2.0.2 a new behaviour for datafile write errors has been implemented. With this release ANY write error to a datafile will cause the instance to abort. Before 11.2.0.2 those errors usually led to an offline datafile if the database operates in archivelog mode (your production database do, don’t they?!) and the datafile does not belong to the SYSTEM tablespace. Internal discussion found this behaviour not up-to-date and alligned with RAC systems and modern storages. Therefore it has been changed and a new underscore parameter got introduced. _DATAFILE_WRITE_ERRORS_CRASH_INSTANCE=TRUE This is the default setting´and the new behaviour beginning with Oracle 11.2.0.2 If you would like to revert to the pre-11.2.0.2 behaviour you’ll have to set in your init.ora/spfile this parameter to false. But keep in mind that there’s a reason why this has been changed. You’ll find more info in MOS Note: 7691270.8 and this topic in the current version of the slides on slide 255. Thanks to Marco for the review!!   And then I received an email from Kurt Van Meerbeeck today. Kurt is pretty well known in the Oracle community. And he’s the owner of jDUL/DUDE, a database unloading tool which bypasses the Oracle database engine and access data direclty from the blocks. Kurt visited the upgrade workshop two weeks ago in Belgium and did highlight to me that since Oracle 11.2.0.1 even though you haven’t set neither SGA_TARGET nor MEMORY_TARGET the database might still do resize operations. Reason why this behaviour has been changed: Prevention of ORA-4031 errors. But on databases with extremly high loads this can cause trouble. Further information can be found in MOS Note:1269139.1 . And the parameter set to TRUE by default is called _MEMORY_IMM_MODE_WITHOUT_AUTOSGA=TRUE This can be found now in the slide set as well on slide number 240. And thanks to Kurt for this information!!

    Read the article

  • ArchBeat Top 10 for November 18-24, 2012

    - by Bob Rhubart
    The Top 10 most popular items shared on the OTN ArchBeat Facebook page for the week of November 18-24, 2012. One-Stop Shop for over 200 On-Demand Oracle Webcasts Webcasts can be a great way to get information about Oracle products without having to go cross-eyed reading yet another document off your computer screen. Oracle's new Webcast Center offers selectable filtering to make it easy to get to the information you want. Yes, you have to register to gain access, but that process is quick, and with over 200 webcasts to choose from you know you'll find useful content. Oracle SOA Suite 11g PS 5 introduces BPEL with conditional correlation for aggregation scenarios | Lucas Jellema An extensive, detailed technical post from Oracle ACE Director Lucas Jellema. Oracle Utilities Application Framework V4.2.0.0.0 Released | Anthony Shorten Principal Product Manager Anthony Shorten shares an overview of the changes implemented in the new release. Fault Handling and Prevention - Part 1 | Guido Schmutz and Ronald van Luttikhuizen In this technical article, part one of a four part series, Oracle ACE Directors Guido Schmutz and Ronald van Luttikhuizen guide you through an introduction to fault handling in a service-oriented environment using Oracle SOA Suite and Oracle Service Bus. Oracle BPM Process Accelerators and process excellence | Andrew Richards "Process Accelerators are ready-to-deploy solutions based on best practices to simplify process management requirements," says Capgemini's Andrew Richards. "They are considered to be 'product grade,' meaning they have been designed; engineered, documented and tested by Oracle themselves to a level that they can be deployed as-is for a solution to a problem or extended as appropriate for a particular scenario." Videos: Getting Started with Java Embedded | The Java Source Interested in Java Embedded? You'll want to check out these videos provided Tori Weildt, including interviews with Oracle's James Allen and Kevin Smith, recorded at ARM TechCon. JPA SQL and Fetching tuning ( EclipseLink ) | Edwin Biemond Oracle ACE Edwin Biemond's post illustrates how to "use the department and employee entity of the HR Oracle demo schema to explain the JPA options you have to control the SQL statements and the JPA relation Fetching." Devoxx 2012 Trip Report - clouds and sunshine | Markus Eisele Oracle ACE Director Markus Eisele shares an extensive and entertaining account of his experience at Devoxx 2012. Towards Ultra-Reusability for ADF - Adaptive Bindings | Duncan Mills "The task flow mechanism embodies one of the key value propositions of the ADF Framework," says Duncan Mills. "However, what if we could do more? How could we make task flows even more re-usable than they are today?" As you might expect, Duncan has answers for those questions. Java Specification Requests in Numbers | Markus Eisele Oracle ACE Director Markus Eisele shares some interesting data culled from the Java Community Process site. Thought for the Day "You can't have great software without a great team, and most software teams behave like dysfunctional families." — Jim McCarthy Source: SoftwareQuotes.com

    Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22  | Next Page >