Search Results

Search found 17622 results on 705 pages for 'external drive'.

Page 17/705 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Hard drive placement

  - by zm15

  I'm a video editor working with large HD files. I am building a new computer and need some help. I will be running 2 hard drives. One with the operating system and all the programs. And one with all the project files I will be working from. I am keeping these seperate. I will be purchasing a 10k rpm hard drive. So i will have a 10k rpm drive, and a 7200rpm drive. Should I put the OS on the faster drive, or put my working files on the faster drive?

  Read the article

• Syncing Large Directories/Filesystems using USB Drive [closed]

  - by Alan Lue

  Does anyone have a solution for syncing large directories/filesystems using just a USB flash drive (and specifically without using a network connection)? The objective is simply to sync a user directory between two computers. The contents of the user directory could amount to a large quantity of data—say, a quantity larger than could be stored on any single USB drive—but the aggregate size of changes that must be propagated by a single sync could easily fit on a USB drive. As an example, suppose a user directory is already synchronized between a desktop and a laptop computer. Here's a use case: Some changes are made in the user directory on the desktop. We mount a USB drive onto the desktop and copy whatever changes need to be applied to the laptop user directory in order to synchronize the desktop and laptop user directories. We now mount the USB drive onto the laptop and apply the changes. The desktop and laptop user directories are now synchronized. Any ideas? Alan

  Read the article

• Why are the external IP of my router not the same as the external IP of my computer

  - by Martin

  I have a standard network setup where all my network devices, both WIFI and ethernet, are connected to the same router. Lately, however, I've been experiencing some very strange behavior. It started as a simple connecting error, when I tried to reach an FTP server using the external IP. Of course I went right into one of those CheckMyIP sites, to double check the IP and it turned out to be correct. Then I went into my router setup, which is through a tool called aiport-tool, because I have an Apple Aiport Extreme router. Turns out the router displays a different external IP, and for some reason that external IP works when I try to access the FTP server. Can anyone explain what is going on? Why are the devices connected to the router displaying an incorrect external IP? BTW i have no VPN/proxy setups on any of my devices.

  Read the article

• EXT4 external hard drive for use with multiple systems

  - by EXTdumb

  I recently bought a external hard drive to store some data on. I use Linux but I am not a power user. If I format the drive to EXT4, is it possible for the permissions to ever screw up and I lost access to my data? I will be plugging the drive into several different linux based computers at work and I frequently hop distros on my main home machine. I need to make sure I don't lose any data because I overlooked something. I am not familiar with EXT 3 or 4. So far I have done this : Formatted drive to EXT4 ran gksudo thunar and changed the permissions to my user account and all settings to read/write Wrote all the files I need to the drive I really appreciate any help.

  Read the article

• My new Xbox 360 drive doesn't show up

  - by RobbieGee

  I bought an Xbox 360 Arcade version a while ago and today I got a 120GB drive from a shop that had a closedown sale. I put the drive on the side as per the picture on the back side of the drive. When I go to settings and look at memory, it only finds the built in memory chip, not the harddrive. Am I doing it correct? I have almost never used my Xbox so I'm not sure if there's anything more to it. I don't think I fitted the drive wrong either, it seems pretty much impossible to do it wrong. The box came with only the drive, it doesn't have any transfer kit or the likes.

  Read the article

• Options to Reformat USB Drive

  - by user8783

  I have a 64GB usb thumb drive. When I plug it into a Windows system (I have tried several machines with both Windows 7 and 8), the system attempts to read it and never completes. The drive does not show up in the device manager, nor does it appear in Computer Management - Disk Management. If I click on the "Safely Remove Hardware" icon, however, I do get an option for "Eject Mass Storage Media", although it never accomplishes anything. Also, as long as the USB drive is connected, I cannot access other USB drives or even restart my computer. It seems as though it locks up Windows Explorer. Is there any option to reformat this drive? It was a great drive up until all this craziness began and I would hate to throw it out because it was rather pricey.

  Read the article

• Syncing Large Directories/Filesystems using USB Drive

  - by Alan Lue

  Does anyone have a solution for syncing large directories/filesystems using just a USB flash drive (and specifically without using a network connection)? The objective is simply to sync a user directory between two computers. The contents of the user directory could amount to a large quantity of data—say, a quantity larger than could be stored on any single USB drive—but the aggregate size of changes that must be propagated by a single sync could easily fit on a USB drive. As an example, suppose a user directory is already synchronized between a desktop and a laptop computer. Here's a use case: Some changes are made in the user directory on the desktop. We mount a USB drive onto the desktop and copy whatever changes need to be applied to the laptop user directory in order to synchronize the desktop and laptop user directories. We now mount the USB drive onto the laptop and apply the changes. The desktop and laptop user directories are now synchronized. Any ideas? Alan

  Read the article

• External Hard Drive needs format problem

  - by Saher

  I recently bought a new ADATA external Classic hard drive 500GB. I have transferred around 29GB of data on it till I install my new windows 7 operating system. After some work with the hard drive (copying / deleting ... files) . I closed it for some reason and it couldn't open again asking me to format. I don't want to format the hard drive, I have important data I need...Is there a way I can retrieve my data. Is Recover My Files program from GetData a right choice??? part 2 of my question: why might such thing happen (require format to open), is it the hard drive problem or is it just a corrupted file or folder...??? Thanks,

  Read the article

• What makes an Apple hard drive special?

  - by Michael Shnitzer

  The Mac Pro has a specific hard drive for sale in the Apple Store for $549.00. The drive has the following specs: Serial ATA 3GB per second 7200 RPM Amazon has a hard drive with the same specs for $169.99. The only difference I can tell is that the Apple hard drive label says it has "Apple HDD Firmware". What exactly is the benefit of this firmware and is there something I am missing that make up for the price difference in these two drives? Update: My initial comparison between the two drive was unfair. Apparently 2TB drives that are 3 GB/S and 7200 RPM are quiet a bit more than $169.99. Dell has a 2 TB SATA Caviar Black from Western Digital that is $319.99, which is closer to Apple's price.

  Read the article

• Working with an external button box

  - by Scott

  I tried this question on Stack Overflow, but I was pointed here, so here goes: For a new project for myself, I am looking for a way to be able to (for example) open a pop-up window on my laptop, by pressing a button on an external device (to be build by myself, or at least bought) connected with USB. Basically I would be looking at something like a Arduino or Raspberry (IF I am looking in the right direction) with buttons on it, and as soon as I hit a button on the external box with physical buttons, a command activates on my laptop and for example opens a popup window in which I can input tekst. Does anyone know: 1) if it is possible to do this at all. 2) What equipment is needed for the external box, what programming is needed. I preffer .net (dot net) but maybe it can only be done with software from the external box. If anyone can point me in the right direction, like make/model of the external box or websites I would be very happy. I have knowledge of Visual Studio/.net but I am willing to learn other languages if .net is not an option for this project. Thanks in advance Scott PS: If anyone knows of some better tags, or at least knows what I mean and needs me to edit the question, please do tell me... I am new on Stack Overflow/Superuser.

  Read the article

• Drive still usable if Seatools reports errors?

  - by Rob

  I have a Seagate 3TB Expansion Desktop drive that was part of a Linux RAID 6 array that failed. I eventually did a zero fill both through Seagate DiscWizard and via Linux dd, neither reported errors. When I ran Seatools now, I got: Short DST - Started 5/31/2014 10:04:36 PM Short DST - Pass 5/31/2014 10:05:37 PM Long Generic - Started 5/31/2014 10:15:19 PM Bad LBA: 518242762 Not Repaired (whole bunch of bad LBAs ommited) Bad LBA: 518715255 Not Repaired Long Generic Aborted 6/1/2014 3:12:18 AM i.e. the short test passed, the long test failed. Unfortunately, the drive is out of warranty, so I can't just RMA it. But I hate tossing a drive that can still be used. So, my questions are: If the zero fill succeeded, and the short test passed, can I still use the whole drive? if not, since I'm using LVM on top of RAID, is there a way to tell either of these to just skip the bad area? If not the above, can I just create partitions before and after the part of the drive with the bad LBAs?

  Read the article

• Installing Ubuntu on an External Drive

  - by Dom

  I am trying to install ububtu on an external drive. I am a programmer who wants to start using Linux. I downloaded the usb installer from the ubuntu website and followed all the steps. But when I get to the part where I have to setup the partitioning, it says an error when moving forward "No root file system is defined". I've been doing some research and I think that I have to partition the external drive but do not know how to do so. The problem is that I only want 20gb used from that external drive and let the rest be used for storage. I am also a musician and use Pro tools so I would like to keep all my files there, but I dont want ubuntu on my main hardrive since the external one is portable. I'd appreciate it also if you could provide me the steps.

  Read the article

• Super slow Western Digial External hard drive

  - by shinokada

  I have 2TB of WD external hard drive. I use windows Vista 32x. on DELL laptop Latitude D630 and connect through USB cable. When I transfer from my C drive to external hard drive it transfer only 3KB/sec. It take 30min to transfer 6MB. It is useless at the moment. Can anyone help me how to speed up please. Thanks in advance.

  Read the article

• problems mounting an external IDE drive via USB in ubuntu

  - by Roy Rico

  I am having a problem connecting a specific IDE drive to my linux box. It's an old drive which I just want to get about 3 GB of files off of. INFO I am trying to connect a 200GB IDE Maxtor Drive, internally and externally... externally: I am using an self powered USB IDE external drive enclosure which I have used to connect various drives, under ubuntu and windows, in the past. The other posts stated it coudl be a problem I think i may have formatted the /dev/sdc partition instead of /dev/sdc1 partition when i originally formatted the drive. internally: I only have one machine left that has an internal IDE interface, and it's got XP on it. I plugged this drive internally into this machine with windows XP and used the ext2/ext3 drivers to mount this drive, but some files have question marks (?) in the file names which is messing up my copy process in windows. I can't delete the files under windows. Ubuntu Linux will not install on my only remaining machine that has IDE controller. I have tried the suggestions in the questions below http://superuser.com/questions/88182/mount-an-external-drive-in-ubuntu http://superuser.com/questions/23210/ubuntu-fails-to-mount-usb-drive it looks like i can see the drive in /proc/partitions $ cat /proc/partitions major minor #blocks name 8 0 78125000 sda 8 1 74894998 sda1 8 2 1 sda2 8 5 3229033 sda5 8 16 199148544 sdb <-- could be my drive? but it's not listed under fdisk -l $ fdisk -l Disk /dev/sda: 80.0 GB, 80000000000 bytes 255 heads, 63 sectors/track, 9726 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xd0f4738c Device Boot Start End Blocks Id System /dev/sda1 * 1 9324 74894998+ 83 Linux /dev/sda2 9325 9726 3229065 5 Extended /dev/sda5 9325 9726 3229033+ 82 Linux swap / Solaris and here is my log of /var/log/messages. with a bunch of weird output, can someone let me know what that weird output is? Mar 3 19:49:40 mala kernel: [687455.112029] usb 1-7: new high speed USB device using ehci_hcd and address 3 Mar 3 19:49:41 mala kernel: [687455.248576] usb 1-7: configuration #1 chosen from 1 choice Mar 3 19:49:41 mala kernel: [687455.267450] Initializing USB Mass Storage driver... Mar 3 19:49:41 mala kernel: [687455.269180] scsi4 : SCSI emulation for USB Mass Storage devices Mar 3 19:49:41 mala kernel: [687455.269410] usbcore: registered new interface driver usb-storage Mar 3 19:49:41 mala kernel: [687455.269416] USB Mass Storage support registered. Mar 3 19:49:46 mala kernel: [687460.270917] scsi 4:0:0:0: Direct-Access Maxtor 6 Y200P0 YAR4 PQ: 0 ANSI: 2 Mar 3 19:49:46 mala kernel: [687460.271485] sd 4:0:0:0: Attached scsi generic sg2 type 0 Mar 3 19:49:46 mala kernel: [687460.278858] sd 4:0:0:0: [sdb] 398297088 512-byte logical blocks: (203 GB/189 GiB) Mar 3 19:49:46 mala kernel: [687460.280866] sd 4:0:0:0: [sdb] Write Protect is off Mar 3 19:50:16 mala kernel: [687460.283784] sdb: Mar 3 19:50:16 mala kernel: [687491.112020] usb 1-7: reset high speed USB device using ehci_hcd and address 3 Mar 3 19:50:47 mala kernel: [687522.120030] usb 1-7: reset high speed USB device using ehci_hcd and address 3 Mar 3 19:51:18 mala kernel: [687553.112034] usb 1-7: reset high speed USB device using ehci_hcd and address 3 Mar 3 19:51:49 mala kernel: [687584.116025] usb 1-7: reset high speed USB device using ehci_hcd and address 3 Mar 3 19:52:02 mala kernel: [687596.170632] type=1505 audit(1267671122.035:31): operation="profile_replace" pid=8426 name=/usr/lib/cups/backend/cups-pdf Mar 3 19:52:02 mala kernel: [687596.171551] type=1505 audit(1267671122.035:32): operation="profile_replace" pid=8426 name=/usr/sbin/cupsd Mar 3 19:52:06 mala kernel: [687600.908056] async/0 D c08145c0 0 7655 2 0x00000000 Mar 3 19:52:06 mala kernel: [687600.908062] e5601d38 00000046 e5774000 c08145c0 e4c2a848 c08145c0 d203973a 0002713d Mar 3 19:52:06 mala kernel: [687600.908072] c08145c0 c08145c0 e4c2a848 c08145c0 00000000 0002713d c08145c0 f0a98c00 Mar 3 19:52:06 mala kernel: [687600.908079] e4c2a5b0 c20125c0 00000002 e5601d80 e5601d44 c056f3be e5601d78 e5601d4c Mar 3 19:52:06 mala kernel: [687600.908087] Call Trace: Mar 3 19:52:06 mala kernel: [687600.908099] [<c056f3be>] io_schedule+0x1e/0x30 Mar 3 19:52:06 mala kernel: [687600.908107] [<c01b2cf5>] sync_page+0x35/0x40 Mar 3 19:52:06 mala kernel: [687600.908111] [<c056f8f7>] __wait_on_bit_lock+0x47/0x90 Mar 3 19:52:06 mala kernel: [687600.908115] [<c01b2cc0>] ? sync_page+0x0/0x40 Mar 3 19:52:06 mala kernel: [687600.908121] [<c020f390>] ? blkdev_readpage+0x0/0x20 Mar 3 19:52:06 mala kernel: [687600.908125] [<c01b2ca9>] __lock_page+0x79/0x80 Mar 3 19:52:06 mala kernel: [687600.908130] [<c015c130>] ? wake_bit_function+0x0/0x50 Mar 3 19:52:06 mala kernel: [687600.908135] [<c01b459f>] read_cache_page_async+0xbf/0xd0 Mar 3 19:52:06 mala kernel: [687600.908139] [<c01b45c2>] read_cache_page+0x12/0x60 Mar 3 19:52:06 mala kernel: [687600.908144] [<c0232dca>] read_dev_sector+0x3a/0x80 Mar 3 19:52:06 mala kernel: [687600.908148] [<c0233d3e>] adfspart_check_ICS+0x1e/0x160 Mar 3 19:52:06 mala kernel: [687600.908152] [<c023339f>] ? disk_name+0xaf/0xc0 Mar 3 19:52:06 mala kernel: [687600.908157] [<c0233d20>] ? adfspart_check_ICS+0x0/0x160 Mar 3 19:52:06 mala kernel: [687600.908161] [<c02334de>] check_partition+0x10e/0x180 Mar 3 19:52:06 mala kernel: [687600.908165] [<c02335f6>] rescan_partitions+0xa6/0x330 Mar 3 19:52:06 mala kernel: [687600.908171] [<c0312472>] ? kobject_get+0x12/0x20 Mar 3 19:52:06 mala kernel: [687600.908175] [<c0312472>] ? kobject_get+0x12/0x20 Mar 3 19:52:06 mala kernel: [687600.908180] [<c039fc43>] ? get_device+0x13/0x20 Mar 3 19:52:06 mala kernel: [687600.908185] [<c03c263f>] ? sd_open+0x5f/0x1b0 Mar 3 19:52:06 mala kernel: [687600.908189] [<c020fda0>] __blkdev_get+0x140/0x310 Mar 3 19:52:06 mala kernel: [687600.908194] [<c020f0ac>] ? bdget+0xec/0x100 Mar 3 19:52:06 mala kernel: [687600.908198] [<c020ff7a>] blkdev_get+0xa/0x10 Mar 3 19:52:06 mala kernel: [687600.908202] [<c0232f30>] register_disk+0x120/0x140 Mar 3 19:52:06 mala kernel: [687600.908207] [<c0308b4d>] ? blk_register_region+0x2d/0x40 Mar 3 19:52:06 mala kernel: [687600.908211] [<c03084f0>] ? exact_match+0x0/0x10 Mar 3 19:52:06 mala kernel: [687600.908216] [<c0308cf0>] add_disk+0x80/0x140 Mar 3 19:52:06 mala kernel: [687600.908221] [<c03084f0>] ? exact_match+0x0/0x10 Mar 3 19:52:06 mala kernel: [687600.908225] [<c0308860>] ? exact_lock+0x0/0x20 Mar 3 19:52:06 mala kernel: [687600.908230] [<c03c53df>] sd_probe_async+0xff/0x1c0

  Read the article

• Use an Ubuntu Live CD to Securely Wipe Your PC’s Hard Drive

  - by Trevor Bekolay

  Deleting files or quickly formatting a drive isn’t enough for sensitive personal information. We’ll show you how to get rid of it for good using a Ubuntu Live CD. When you delete a file in Windows, Ubuntu, or any other operating system, it doesn’t actually destroy the data stored on your hard drive, it just marks that data as “deleted.” If you overwrite it later, then that data is generally unrecoverable, but if the operating system don’t happen to overwrite it, then your data is still stored on your hard drive, recoverable by anyone who has the right software. By securely delete files or entire hard drives, your data will be gone for good. Note: Modern hard drives are extremely sophisticated, as are the experts who recover data for a living. There is no guarantee that the methods covered in this article will make your data completely unrecoverable; however, they will make your data unrecoverable to the majority of recovery methods, and all methods that are readily available to the general public. Shred individual files Most of the data stored on your hard drive is harmless, and doesn’t reveal anything about you. If there are just a few files that you know you don’t want someone else to see, then the easiest way to get rid of them is a built-in Linux utility called shred. Open a terminal window by clicking on Applications at the top-left of the screen, then expanding the Accessories menu and clicking on Terminal. Navigate to the file that you want to delete using cd to change directories and ls to list the files and folders in the current directory. As an example, we’ve got a file called BankInfo.txt on a Windows NTFS-formatted hard drive. We want to delete it securely, so we’ll call shred by entering the following in the terminal window: shred <file> which is, in our example: shred BankInfo.txt Notice that our BankInfo.txt file still exists, even though we’ve shredded it. A quick look at the contents of BankInfo.txt make it obvious that the file has indeed been securely overwritten. We can use some command-line arguments to make shred delete the file from the hard drive as well. We can also be extra-careful about the shredding process by upping the number of times shred overwrites the original file. To do this, in the terminal, type in: shred –remove –iterations=<num> <file> By default, shred overwrites the file 25 times. We’ll double this, giving us the following command: shred –remove –iterations=50 BankInfo.txt BankInfo.txt has now been securely wiped on the physical disk, and also no longer shows up in the directory listing. Repeat this process for any sensitive files on your hard drive! Wipe entire hard drives If you’re disposing of an old hard drive, or giving it to someone else, then you might instead want to wipe your entire hard drive. shred can be invoked on hard drives, but on modern file systems, the shred process may be reversible. We’ll use the program wipe to securely delete all of the data on a hard drive. Unlike shred, wipe is not included in Ubuntu by default, so we have to install it. Open up the Synaptic Package Manager by clicking on System in the top-left corner of the screen, then expanding the Administration folder and clicking on Synaptic Package Manager. wipe is part of the Universe repository, which is not enabled by default. We’ll enable it by clicking on Settings > Repositories in the Synaptic Package Manager window. Check the checkbox next to “Community-maintained Open Source software (universe)”. Click Close. You’ll need to reload Synaptic’s package list. Click on the Reload button in the main Synaptic Package Manager window. Once the package list has been reloaded, the text over the search field will change to “Rebuilding search index”. Wait until it reads “Quick search,” and then type “wipe” into the search field. The wipe package should come up, along with some other packages that perform similar functions. Click on the checkbox to the left of the label “wipe” and select “Mark for Installation”. Click on the Apply button to start the installation process. Click the Apply button on the Summary window that pops up. Once the installation is done, click the Close button and close the Synaptic Package Manager window. Open a terminal window by clicking on Applications in the top-left of the screen, then Accessories > Terminal. You need to figure our the correct hard drive to wipe. If you wipe the wrong hard drive, that data will not be recoverable, so exercise caution! In the terminal window, type in: sudo fdisk -l A list of your hard drives will show up. A few factors will help you identify the right hard drive. One is the file system, found in the System column of  the list – Windows hard drives are usually formatted as NTFS (which shows up as HPFS/NTFS). Another good identifier is the size of the hard drive, which appears after its identifier (highlighted in the following screenshot). In our case, the hard drive we want to wipe is only around 1 GB large, and is formatted as NTFS. We make a note of the label found under the the Device column heading. If you have multiple partitions on this hard drive, then there will be more than one device in this list. The wipe developers recommend wiping each partition separately. To start the wiping process, type the following into the terminal: sudo wipe <device label> In our case, this is: sudo wipe /dev/sda1 Again, exercise caution – this is the point of no return! Your hard drive will be completely wiped. It may take some time to complete, depending on the size of the drive you’re wiping. Conclusion If you have sensitive information on your hard drive – and chances are you probably do – then it’s a good idea to securely delete sensitive files before you give away or dispose of your hard drive. The most secure way to delete your data is with a few swings of a hammer, but shred and wipe from a Ubuntu Live CD is a good alternative! Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDScan a Windows PC for Viruses from a Ubuntu Live CDRecover Deleted Files on an NTFS Hard Drive from a Ubuntu Live CDCreate a Bootable Ubuntu 9.10 USB Flash DriveCreate a Bootable Ubuntu USB Flash Drive the Easy Way TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Office 2010 Product Guides Google Maps Place marks – Pizza, Guns or Strip Clubs Monitor Applications With Kiwi LocPDF is a Visual PDF Search Tool Download Free iPad Wallpapers at iPad Decor Get Your Delicious Bookmarks In Firefox’s Awesome Bar

  Read the article

• Boot From a USB Drive Even if your BIOS Won’t Let You

  - by Trevor Bekolay

  You’ve always got a trusty bootable USB flash drive with you to solve computer problems, but what if a PC’s BIOS won’t let you boot from USB? We’ll show you how to make a CD or floppy disk that will let you boot from your USB drive. This boot menu, like many created before USB drives became cheap and commonplace, does not include an option to boot from a USB drive. A piece of freeware called PLoP Boot Manager solves this problem, offering an image that can burned to a CD or put on a floppy disk, and enables you to boot to a variety of devices, including USB drives. Put PLoP on a CD PLoP comes as a zip file, which includes a variety of files. To put PLoP on a CD, you will need either plpbt.iso or plpbtnoemul.iso from that zip file. Either disc image should work on most computers, though if in doubt plpbtnoemul.iso should work “everywhere,” according to the readme included with PLoP Boot Manager. Burn plpbtnoemul.iso or plpbt.iso to a CD and then skip to the “booting PLoP Boot Manager” section. Put PLoP on a Floppy Disk If your computer is old enough to still have a floppy drive, then you will need to put the contents of the plpbt.img image file found in PLoP’s zip file on a floppy disk. To do this, we’ll use a freeware utility called RawWrite for Windows. We aren’t fortunate enough to have a floppy drive installed, but if you do it should be listed in the Floppy drive drop-down box. Select your floppy drive, then click on the “…” button and browse to plpbt.img. Press the Write button to write PLoP boot manager to your floppy disk. Booting PLoP Boot Manager To boot PLoP, you will need to have your CD or floppy drive boot with higher precedence than your hard drive. In many cases, especially with floppy disks, this is done by default. If the CD or floppy drive is not set to boot first, then you will need to access your BIOS’s boot menu, or the setup menu. The exact steps to do this vary depending on your BIOS – to get a detailed description of the process, search for your motherboard’s manual (or your laptop’s manual if you’re working with a laptop). In general, however, as the computer boots up, some important keyboard strokes are noted somewhere prominent on the screen. In our case, they are at the bottom of the screen. Press Escape to bring up the Boot Menu. Previously, we burned a CD with PLoP Boot Manager on it, so we will select the CD-ROM Drive option and hit Enter. If your BIOS does not have a Boot Menu, then you will need to access the Setup menu and change the boot order to give the floppy disk or CD-ROM Drive higher precedence than the hard drive. Usually this setting is found in the “Boot” or “Advanced” section of the Setup menu. If done correctly, PLoP Boot Manager will load up, giving a number of boot options. Highlight USB and press Enter. PLoP begins loading from the USB drive. Despite our BIOS not having the option, we’re now booting using the USB drive, which in our case holds an Ubuntu Live CD! This is a pretty geeky way to get your PC to boot from a USB…provided your computer still has a floppy drive. Of course if your BIOS won’t boot from a USB it probably has one…or you really need to update it. Download PLoP Boot Manager Download RawWrite for Windows Similar Articles Productive Geek Tips Create a Bootable Ubuntu 9.10 USB Flash DriveReinstall Ubuntu Grub Bootloader After Windows Wipes it OutCreate a Bootable Ubuntu USB Flash Drive the Easy WayBuilding a New Computer – Part 3: Setting it UpInstall Windows XP on Your Pre-Installed Windows Vista Computer TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Office 2010 reviewed in depth by Ed Bott FoxClocks adds World Times in your Statusbar (Firefox) Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7

  Read the article

• Strange performance differences in read/write from/to USB flash drive

  - by Mario De Schaepmeester

  When copying files from my 8GB USB 2.0 flash drive with Windows 7 to a traditional hard drive, the average speed is between 25 and 30 MB/s. When doing the reverse, copying to the USB drive, the speed is 5MB/s average. I have tested this with about 4.5GB of files, a mixture of smaller and larger ones. The observations were the same on both FAT32 and exFAT file systems on the USB drive, NTFS on the internal hard disk. I don't think I can be mistaken in saying that flash memory has a lot higher performance than a spinning hard drive in both terms of reading and writing. For both memory types, reading should be faster than writing too. Now I wonder, how can it be that copying files from a fast read memory to a faster write memory is actually slower than copying files from a fast read memory to a slow write memory? I think that the files are stored in RAM before being copied over too, and there's caching as well, but I don't see how even that could tip the balance. It can only be in the advantage of writing to the USB drive, since it is "closer" to the SATA system than the USB port and it will receive data from the internal SATA HDD faster. Perhaps my way of thinking is all wrong or it just depends on the manufacturer of the USB pen. But I am curious.

  Read the article

• BIOS not detecting working SATA hard drive.

  - by Evan

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• BIOS not detecting working SATA hard drive

  - by user28927

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• SATA DVD drive refuses to read movie DVDs

  - by poke

  Hey, I have a problem with my DVD Drive (Asus DRW-2014L1T, most current firmware installed) on Windows 7 x64. When I insert a DVD movie and Windows starts to access the drive (for autoplay, or when I manually click on the drive icon), my computer hangs up in a particular way, while trying to read the disk. Explorer stops reacting and several programs won't run or their launch is horribly delayed (like the device manager). In th end, I can't access the movie and can't even eject the disk (probably because Windows is still trying to access it). To get the disk out of the drive I then have to reboot (which sometimes doesn't work either) and eject the disk before Windows boots. BIOS recognizes the drive just fine, and Windows is also able to read data disks (tried it with some software disks), but just refuses any movies. I have checked the region code in the device manager, but it is correct. My notebook is reading the disks just fine btw.. I remember having the same problem with an older drive as well, but I don't remember what I did to make it work again (maybe I didn't even fix the problem back then). I do remember however that booting with the disk inserted made Windows recognize the disk, however this doesn't work in this situation either. Do you have any idea what to do to fix that problem?

  Read the article

• Recover data from hard drive with partitions (but not most data) overwritten

  - by Macha

  I have a 500GB hard drive I've been keeping around to recover data from that I removed from a failing NAS drive that got sort of... erratic at the end. I finally got rid of the NAS when during a firmware update it removed the partition table. Fast forward to a week ago, when I was building a new PC, and a mixup resulted in me placing the hard drive in question in the new PC and installing Windows XP on the first 100GB. I'm presuming any data on that first 100GB is now gone, but for the rest of it, is there any way I can recover it at home, as professional data recovery is currently too expensive? I have a blank 1TB HDD if I can store any images of that hard drive on. The problem was definitely with the NAS and not the hard drive, as the hard drive had a successful install of Windows when mistakenly place in the new PC, and there were capacitors in the NAS's circuitry clearly broken. The data I want to recover (in order of priority) is: High: Some jpgs of family photos. Medium: Some RAW files. (There are also jpg versions of all of these) Low: Some mp3s, avis and ISOs, I can re-rip most of these if need be, but it'd be handy not to have to. (I don't need a backup lecture, and if you can hold it in from nagging Jeff Atwood for it, you can hold it in from nagging me for it) In short: The partition tables are gone and overwritten. The data is not overwritten, except for an amount equal to the size of a Windows XP SP3 installation.

  Read the article

• Replacing Failing RAID 1 Drive

  - by mrduclaw

  I hope this is a simple question, but I simply don't know anything about RAID. Some time ago I received a machine that, as I understand it, has two drives in it under RAID 1 (or so that one drive is mirrored on the other and appears as just 1 drive to the OS). Recently, one of these drives has started marking a clicking noise and I would like to replace it. I believe the machine has a hardware RAID controller on the motherboard that handles the RAID stuff, but if it matters the Operating System is Windows XP 32-bit. Is the solution to my problem as simple as buying another drive that is of the same capacity and plugging it in where the clicking drive is currently? Or could I possibly lose everything if the drive that's clicking is the one being mirrored on to the other drive? Is there some menu I need to find before unhooking things? Any best practices out there? I'm sure I'm leaving out some required information, so please just tell me what I'm missing. Thanks!

  Read the article

• Putting and configuring grub on an external drive

  - by HisDudeness

  I want to put a bunch of minor emergency operating systems (such as GParted Live, DSL, Puppy Linux and so on) on a partitioned USB pen drive, with a dedicated grub boot loader on it, which I want to start when I select the drive in the BIOS to boot. The problem is: when writing grub boot options I must tell where kernel and initial ram files are located, but the USB drive can have different letters depending on when I did plug it in, if some others external drive were mounted. So, how can I write appropriate options which automatically refer to the drive grub is installed on without having to specify absolute paths, which might change (I mean, like (hd1,msdos1) ot /dev/sdb1)? And, while we are at it, can I have grub working on a device without an operating system on it to which it can refer? I mean, I want to address the command sudo grub-install /dev/sdb from the LMDE system I'm on right now, but I won't have LMDE on my pen drive. Is that a problem? And installing grub on another device, will I keep the grub I have right now on my HDD?

  Read the article

• how can i safely remove an external hard drive?

  - by Edmond Condillac

  Two of the three icons of the drive's partitions show on the desktop. One has disappeared and the contents are not accessible. Right clicking on the desktop icon of the partition gives the option to eject. Then the error message shows that the drive is busy and cannot be shut down. The drive is continually pinning. Kindly advise if possible how to safely remove the drive. Can the lost icon of the third drive and the datd contained in it be found, please? Kind regards

  Read the article

• External USB drive is failing

  - by dma_k

  I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >