Search Results

Search found 609 results on 25 pages for 'kitten 94'.

Page 17/25 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Resolving CloudFlare DNS related mail delivery problems

  - by Andy Castles

  I recently started using CloudFlare and am having a few teething problems. Our domain is netlanguages.com and while we have a lot of sub-domains listen, we are currently only trialling a few of the servers through the CloudFlare CDN (for example, www.netlanguages.com is enabled for CDN, netlanguages.com is not). The actual CDN service seems to be reliable, but the problem that we are having is with DNS, and specifically with mail delivery. The background is that we have contact forms on our web site which use PHP mail() to send the details to end-users' email addresses, with the "from" address of the messages being [email protected] which is a valid address on our mail server. Most of the mails are arriving correctly, but a few specific people are not receiving them. The webserver uses qmail to deliver the messages, and the qmail log files show us some of the errors that the receiving mail servers return when they reject the mail delivery attempt. Two examples: Connected to 94.100.176.20 but sender was rejected./Remote host said: 421 DNS problem (interdominios.netlanguages.com). Try again later Connected to 213.186.33.29 but sender was rejected./Remote host said: 451 DNS temporary failure (#4.3.0) From what I can tell, the receiving SMTP server is doing a DNS lookup of some description on either the host of the "from" email address (netlanguages.com) or the server name given in the EHLO command of the SMTP conversation (in the first example above, interdominios.netlanguages.com), both of which should resolve to non-CloudFlare IP addresses. I've read that the CloudFlare DNS service is very reliable and fast but both of the problems above seem to point to a problem with remote servers unable to do DNS lookups. I should also point out that we changed our DNS to CloudFlare on 6th Feb, and since then started experiencing these mail delivery problems. On 22nd Feb we moved our DNS away from CloudFlare to see if the issues were related to CloudFlare and after a few hours delivery began to work. Then on 26th Feb I moved the DNS back to CloudFlare again and delivery problems started again. The issues definitely seems to be related to DNS, but I don't know if it's a configuration issue, or something else. Finally, I should say that our two DNS MX records point to non-CDN A record IP addresses, interdominios.netlanguages.com (the web and qmail server) also points to a non-CDN A record IP address. Does anyone know what the problem could be here? Any light you can shed on this will be most appreciated. Many thanks, Andy

  Read the article

• Disk IO causing high load on Xen/CentOS guest

  - by Peter Lindqvist

  I'm having serious issues with a xen based server, this is on the guest partition. It's a paravirtualized CentOS 5.5. The following numbers are taken from top while copying a large file over the network. If i copy the file another time the speed decreases in relation to load average. So the second time it's half the speed of the first time. It needs some time to cool off after this. Load average slowly decreases until it's once again usable. ls / takes about 30 seconds. top - 13:26:44 up 13 days, 21:44, 2 users, load average: 7.03, 5.08, 3.15 Tasks: 134 total, 2 running, 132 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.1%sy, 0.0%ni, 25.3%id, 74.5%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 1048752k total, 1041460k used, 7292k free, 3116k buffers Swap: 2129912k total, 40k used, 2129872k free, 904740k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1506 root 10 -5 0 0 0 S 0.3 0.0 0:03.94 cifsd 1 root 15 0 2172 644 556 S 0.0 0.1 0:00.08 init Meanwhile the host is ~0.5 load avg and steady over time. ~50% wait Server hardware is dual xeon, 3gb ram, 170gb scsi 320 10k rpm, and shouldn't have any problems with copying files over the network. disk = [ "tap:aio:/vm/dev01.img,xvda,w" ] I also get these in the log INFO: task syslogd:1350 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syslogd D 00062E4F 2208 1350 1 1353 1312 (NOTLB) c0ef0ed0 00000286 6e71a411 00062e4f c0ef0f18 00000009 c0f20000 6e738bfd 00062e4f 0001e7ec c0f2010c c181a724 c1abd200 00000000 ffffffff c0ef0ecc c041a180 00000000 c0ef0ed8 c03d6a50 00000000 00000000 c03d6a00 00000000 Call Trace: [<c041a180>] __wake_up+0x2a/0x3d [<ee06a1ea>] log_wait_commit+0x80/0xc7 [jbd] [<c043128b>] autoremove_wake_function+0x0/0x2d [<ee065661>] journal_stop+0x195/0x1ba [jbd] [<c0490a32>] __writeback_single_inode+0x1a3/0x2af [<c04568ea>] do_writepages+0x2b/0x32 [<c045239b>] __filemap_fdatawrite_range+0x66/0x72 [<c04910ce>] sync_inode+0x19/0x24 [<ee09b007>] ext3_sync_file+0xaf/0xc4 [ext3] [<c047426f>] do_fsync+0x41/0x83 [<c04742ce>] __do_fsync+0x1d/0x2b [<c0405413>] syscall_call+0x7/0xb ======================= I have tried disabling irqbalanced as suggested here but it does not seem to make any difference.

  Read the article

• Why can I view my site over a 3G connection but not through my wifi?

  - by Jonathan

  So, I am sitting in my office with four computers on the same network and internet connection. Two of the computers can visit this particular website. Two of the computer get a message "Google Chrome could not find". I have tried FF and IE also with the same problem. I can view the site 90% of the time on two of the working computers although the site seems slow and sometimes I also get the same errors as the other two computers. I have flushed the DNS, reset the router, tested the site on other peoples computers with success. Is this likely to be a site issue, an ISP issue, a hosting issue? Any advice is greatly appreciated. Here is the ping from the working machine: C:\Users\Jon>ping www.balihaicruises.com Pinging www.balihaicruises.com [208.113.173.102] with 32 bytes of data: Reply from 208.113.173.102: bytes=32 time=331ms TTL=47 Reply from 208.113.173.102: bytes=32 time=327ms TTL=47 Reply from 208.113.173.102: bytes=32 time=326ms TTL=47 Reply from 208.113.173.102: bytes=32 time=329ms TTL=47 Ping statistics for 208.113.173.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 326ms, Maximum = 331ms, Average = 328ms Traceroute: Tracing route to www.balihaicruises.com [208.113.173.102] over a maximum of 30 hops: 1 1 ms 17 ms 3 ms 192.168.1.1 2 42 ms 37 ms 36 ms 180.254.224.1 3 39 ms 47 ms 40 ms 180.252.1.69 4 36 ms 616 ms 57 ms 61.94.115.221 5 84 ms 76 ms 80 ms 180.240.191.98 6 73 ms 80 ms 72 ms 180.240.191.97 7 157 ms 143 ms 116 ms 180.240.190.82 8 115 ms 113 ms 120 ms ae1-123.hkg11.ip4.tinet.net [183.182.80.93] 9 331 ms 332 ms 335 ms xe-3-2-1.was14.ip4.tinet.net [89.149.184.30] 10 327 ms 330 ms 331 ms internap-gw.ip4.tinet.net [77.67.69.254] 11 437 ms 415 ms 350 ms border10.pc2-bbnet2.wdc002.pnap.net [216.52.127.73] 12 322 ms 823 ms 398 ms dreamhost-2.border10.wdc002.pnap.net [216.52.125.74] 13 328 ms 336 ms 326 ms ip-208-113-156-4.dreamhost.com [208.113.156.4] 14 326 ms 328 ms 336 ms ip-208-113-156-14.dreamhost.com [208.113.156.14] 15 327 ms 331 ms 333 ms apache2-udder.crisp.dreamhost.com [208.113.173.102] And then for the machine that doesn't work: C:\Users\Microsoft>ping www.balihaicruises.com Ping request could not find host www.balihaicruises.com. Please check the name and try again. C:\Users\Microsoft>tracert www.balihaicruises.com Unable to resolve target system name www.balihaicruises.com.

  Read the article

• Increase Timeout for remote sessions in Debian 5 Lenny

  - by Ash

  I always get a remote connection time out when using PuTTy and also when i send emails with attachments from a mail sever installed on Debian. I always get this error. I'm not sure if this is firewall or the new Debian 5 installation which i made. Is there any settings i need to fix after fresh install. Any inputs are highly appreciated. This error is pulling my brains out. Thanks. Error: 2011-01-10 15:21:13,454 INFO [btpool0-23://69.19.19.89/service/upload?fmt=extended] [[email protected];mid=72;ip=10.10.01.78;ua=Mozilla/5.0 (Windows;; U;; Windows NT 5.2;; en-US;; rv:1.9.2.13) Gecko/20101203 Firefox/3.6.13 (.NET CLR 3.5.30729);] FileUploadServlet - File upload failed org.apache.commons.fileupload.FileUploadBase$IOFileUploadException: Processing of multipart/form-data request failed. timeout at org.apache.commons.fileupload.FileUploadBase.parseRequest(FileUploadBase.java:367) at org.apache.commons.fileupload.servlet.ServletFileUpload.parseRequest(ServletFileUpload.java:126) at com.zimbra.cs.service.FileUploadServlet.handleMultipartUpload(FileUploadServlet.java:430) at com.zimbra.cs.service.FileUploadServlet.doPost(FileUploadServlet.java:412) at javax.servlet.http.HttpServlet.service(HttpServlet.java:727) at com.zimbra.cs.servlet.ZimbraServlet.service(ZimbraServlet.java:181) at javax.servlet.http.HttpServlet.service(HttpServlet.java:820) at org.mortbay.jetty.servlet.ServletHolder.handle(ServletHolder.java:511) at org.mortbay.jetty.servlet.ServletHandler$CachedChain.doFilter(ServletHandler.java:1166) at com.zimbra.cs.servlet.SetHeaderFilter.doFilter(SetHeaderFilter.java:79) at org.mortbay.jetty.servlet.ServletHandler$CachedChain.doFilter(ServletHandler.java:1157) at org.mortbay.servlet.UserAgentFilter.doFilter(UserAgentFilter.java:81) at org.mortbay.servlet.GzipFilter.doFilter(GzipFilter.java:132) at org.mortbay.jetty.servlet.ServletHandler$CachedChain.doFilter(ServletHandler.java:1157) at org.mortbay.jetty.servlet.ServletHandler.handle(ServletHandler.java:388) at org.mortbay.jetty.security.SecurityHandler.handle(SecurityHandler.java:218) at org.mortbay.jetty.servlet.SessionHandler.handle(SessionHandler.java:182) at org.mortbay.jetty.handler.ContextHandler.handle(ContextHandler.java:765) at org.mortbay.jetty.webapp.WebAppContext.handle(WebAppContext.java:418) at org.mortbay.jetty.handler.ContextHandlerCollection.handle(ContextHandlerCollection.java:230) at org.mortbay.jetty.handler.HandlerCollection.handle(HandlerCollection.java:114) at org.mortbay.jetty.handler.HandlerWrapper.handle(HandlerWrapper.java:152) at org.mortbay.jetty.handler.rewrite.RewriteHandler.handle(RewriteHandler.java:230) at org.mortbay.jetty.handler.HandlerWrapper.handle(HandlerWrapper.java:152) at org.mortbay.jetty.handler.DebugHandler.handle(DebugHandler.java:77) at org.mortbay.jetty.handler.HandlerWrapper.handle(HandlerWrapper.java:152) at org.mortbay.jetty.Server.handle(Server.java:326) at org.mortbay.jetty.HttpConnection.handleRequest(HttpConnection.java:543) at org.mortbay.jetty.HttpConnection$RequestHandler.content(HttpConnection.java:939) at org.mortbay.jetty.HttpParser.parseNext(HttpParser.java:755) at org.mortbay.jetty.HttpParser.parseAvailable(HttpParser.java:218) at org.mortbay.jetty.HttpConnection.handle(HttpConnection.java:405) at org.mortbay.io.nio.SelectChannelEndPoint.run(SelectChannelEndPoint.java:413) at org.mortbay.thread.BoundedThreadPool$PoolThread.run(BoundedThreadPool.java:451) Caused by: org.mortbay.jetty.EofException: timeout at org.mortbay.jetty.HttpParser$Input.blockForContent(HttpParser.java:1172) at org.mortbay.jetty.HttpParser$Input.read(HttpParser.java:1122) at org.apache.commons.fileupload.MultipartStream$ItemInputStream.makeAvailable(MultipartStream.java:977) at org.apache.commons.fileupload.MultipartStream$ItemInputStream.read(MultipartStream.java:887) at java.io.InputStream.read(InputStream.java:85) at org.apache.commons.fileupload.util.Streams.copy(Streams.java:94) at org.apache.commons.fileupload.util.Streams.copy(Streams.java:64) at org.apache.commons.fileupload.FileUploadBase.parseRequest(FileUploadBase.java:362) ... 33 more

  Read the article

• ssh refuses to authenticate keys

  - by MixturaDementiae

  So I am setting up a connection between my machine [fedora 17] and a virtual machine running in Virtual Box in which is running CentOS 5. I have installed openssh from the repositories on CentOS, and I have configured everything as it follows: Protocol 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key SyslogFacility AUTHPRIV PermitRootLogin yes RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile /home/pigreco/.ssh/authorized_keys PasswordAuthentication no ChallengeResponseAuthentication yes GSSAPIAuthentication yes GSSAPICleanupCredentials yes UsePAM yes AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL LANGUAGE AcceptEnv XMODIFIERS X11Forwarding yes Subsystem sftp /usr/libexec/openssh/sftp-server this is the configuration file sshd_config on the server i.e. on the CentOS. Moreover I have created a public/private key pair as usual on the .ssh/ folder in my home directory in my OS, i.e. Fedora, and then I've copied with scp the id_rsa.pub to the server and then I have appended its content to the file .ssh/authorized_keys on the server machine. The error that I get is the following: OpenSSH_5.9p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 50: Applying options for * debug1: Connecting to 192.168.100.13 [192.168.100.13] port 22. debug1: Connection established. debug1: identity file /home/mayhem/.ssh/identity type -1 debug1: identity file /home/mayhem/.ssh/identity-cert type -1 debug1: identity file /home/mayhem/.ssh/id_rsa type 1 debug1: identity file /home/mayhem/.ssh/id_rsa-cert type -1 debug1: identity file /home/mayhem/.ssh/id_dsa type -1 debug1: identity file /home/mayhem/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 16:e5:72:d1:37:94:1b:5e:3d:3a:e5:da:6f:df:0c:08 debug1: Host '192.168.100.13' is known and matches the RSA host key. debug1: Found key in /home/mayhem/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,keyboard-interactive debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/mayhem/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 279 Agent admitted failure to sign using the key. debug1: Trying private key: /home/mayhem/.ssh/identity debug1: Trying private key: /home/mayhem/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Do you have some good suggestion of what I can do? thank you

  Read the article

• Apache won't serve images larger than ~2K

  - by dtbaker

  Hello, Just upgraded an old box to Ubuntu to 10.04.2 LTS. Apache will not display images to a browser that are over about 2K. Small images seem to display fine. Static HTML and PHP continues to works fine as well. Installed: apache2 2.2.14-5ubuntu8.4 apache2-mpm-prefork 2.2.14-5ubuntu8.4 apache2-utils 2.2.14-5ubuntu8.4 apache2.2-bin 2.2.14-5ubuntu8.4 apache2.2-common 2.2.14-5ubuntu8.4 here is an ngrep of an image that doesn't display fine in the browser: T 192.168.0.4:32907 - 192.168.0.54:80 [AP] GET /path/path/logo.png HTTP/1.1..Host: 192.1 68.0.54..Connection: keep-alive..Accept: application/xml,application/xhtml+ xml,text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5..User-Ag ent: Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/534.13 (KHTML, like Gecko) Chrome/9.0.597.98 Safari/534.13..Accept-Enco ding: gzip,deflate,sdch..Accept-Language: en-US,en;q=0.8..Accept- Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3.... T 192.168.0.54:80 - 192.168.0.4:32907 [A] HTTP/1.1 200 OK..Date: Wed, 09 Mar 2011 05:28:38 GMT..Server: Apa che/2.2.14 (Ubuntu)..Last-Modified: Tue, 05 Oct 2010 11:59:17 GMT ..ETag: "17b6f4-15fe-491dd63eb2f40"..Accept-Ranges: bytes..Conten t-Length: 5630..Keep-Alive: timeout=15, max=100..Connection: Keep -Alive..Content-Type: image/png.....PNG........IHDR...!...v...... .%.....sRGB.........bKGD..............pHYs.................tIME.. etc... This looks ok to me! I have tried firefox and chrome, both display small images fine but when a large image is requested the browser prompts to download the file. When the image file is saved to the local computer it is corrupt, it also takes a long time to save which makes me think the browser cannot see the content-length header sent from apache. Also when I look at the saved image file it includes the headers from apache, along with a bit of garbage at the top, like so: vi logo.png: ^@^UÅd^@$^]V^S^H^@E^@^Q,n!@^@@^F^@^@À¨^@6À¨^@^D^@P^Y¬rÇŹéw^P^@Ú^@^@^A^A^H ^@^GÝ^]^@pbSHTTP/1.1 200 OK^M Date: Wed, 09 Mar 2011 04:47:04 GMT^M Server: Apache/2.2.14 (Ubuntu)^M Last-Modified: Tue, 05 Oct 2010 11:59:17 GMT^M ETag: "17b6ff-157c-491dd63eb2f40"^M Accept-Ranges: bytes^M Content-Length: 5500^M Keep-Alive: timeout=15, max=94^M Connection: Keep-Alive^M Content-Type: image/png^M ^M PNG^M etc... Any ideas? It's driving me nuts. There is nothing in apache error logs, and permissions are fine (because the image data is there, it's just somewhat corrupt). There's no proxy or iptables on this ubuntu box either. Thanks heaps!! Dave ps: just tried on IE from a different computer, same problem :( pps: rebooted server, no help.

  Read the article

• How do I permanently delete e-mail messages in the sendmail queue and keep them from coming back?

  - by Steven Oxley

  I have a pretty annoying problem here. I have been testing an application and have created some test e-mails to bogus e-mail addresses (not to mention that my server isn't really set up to send e-mail anyway). Of course, sendmail is not able to send these messages and they have been getting stuck in the sendmail queue. I want to manually delete the messages that have been building up in the queue instead of waiting the 5 days that sendmail usually takes to stop retrying. I am using Ubuntu 10.04 and /var/spool/mqueue/ is the directory in which every how-to I have read says the e-mails that are queued up are kept. When I delete the files in this directory, sendmail stops trying to process the e-mails until what appears to be a cron script runs and re-populates this directory with the messages I don't want sent. Here are some lines from my syslog: Jun 2 17:35:19 sajo-laptop sm-mta[9367]: o530SlbK009365: to=, ctladdr= (33/33), delay=00:06:27, xdelay=00:06:22, mailer=esmtp, pri=120418, relay=e.mx.mail.yahoo.com. [67.195.168.230], dsn=4.0.0, stat=Deferred: Connection timed out with e.mx.mail.yahoo.com. Jun 2 17:35:48 sajo-laptop sm-mta[9149]: o4VHn3cw003597: to=, ctladdr= (33/33), delay=2+06:46:45, xdelay=00:34:12, mailer=esmtp, pri=3540649, relay=mx2.hotmail.com. [65.54.188.94], dsn=4.0.0, stat=Deferred: Connection timed out with mx2.hotmail.com. Jun 2 17:39:02 sajo-laptop CRON[9510]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -type f -cmin +$(/usr/lib/php5/maxlifetime) -print0 | xargs -n 200 -r -0 rm) Jun 2 17:39:43 sajo-laptop sm-mta[9372]: o52LHK4s007585: to=, ctladdr= (33/33), delay=03:22:18, xdelay=00:06:28, mailer=esmtp, pri=1470404, relay=c.mx.mail.yahoo.com. [206.190.54.127], dsn=4.0.0, stat=Deferred: Connection timed out with c.mx.mail.yahoo.com. Jun 2 17:39:50 sajo-laptop sm-mta[9149]: o51I8ieV004377: to=, ctladdr= (33/33), delay=1+06:31:06, xdelay=00:03:57, mailer=esmtp, pri=6601668, relay=alt4.gmail-smtp-in.l.google.com. [74.125.79.114], dsn=4.0.0, stat=Deferred: Connection timed out with alt4.gmail-smtp-in.l.google.com. Jun 2 17:40:01 sajo-laptop CRON[9523]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Does anyone know how I can get rid of these messages permanently? As a side note, I'd also like to know if there is a way to set up sendmail to "fake" sending e-mail. Is there?

  Read the article

• How to start nginx via different port(other than 80)

  - by Zhao Peng

  Hi I am a newbie on nginx, I tried to set it up on my server(running Ubuntu 4), which already has apache running. So after I apt-get install it, I tried to start nginx. Then I get the message like this: Starting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) That makes sense as Apache is using port 80. Then I tried to modify nginx.conf, I reference some articles, so I changed it like so: server { listen 8080; location / { proxy_pass http://94.143.9.34:9500; proxy_set_header Host $host:8080; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Via "nginx"; } After saving this and try to start nginx again, I still get the same error as previously. I cannot really find a related post about this, could any good people shred some light? Thanks in advance :) ========================================================================= I should post all the content in conf here: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; server { listen 81; location / { proxy_pass http://94.143.9.34:9500; proxy_set_header Host $host:81; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Via "nginx"; } } } mail { See sample authentication script at: http://wiki.nginx.org/NginxImapAuthenticateWithApachePhpScript auth_http localhost/auth.php; pop3_capabilities "TOP" "USER"; imap_capabilities "IMAP4rev1" "UIDPLUS"; server { listen localhost:110; protocol pop3; proxy on; } server { listen localhost:143; protocol imap; proxy on; } } Basically, I changed nothing except adding the server part.

  Read the article

• Windows 2012 VPN setup without Active Directory

  - by iss42

  I have followed the guide here: http://www.youtube.com/watch?v=9qbpxKRb-94 But my situation differs with respect to there being no AD (Active Directory) setup. When I try to connect I get this in the server event log: "The user xx connected from x.x.x.x but failed an authentication attempt due to the following reason: The account does not have permission to dial in." Is there a way to enable this without AD?

  Read the article

• 10.6.4 Apple Wiki: New just created users can do nothing?

  - by beefon

  Hello, After update to 10.6.4 there's an issue: any new users that I create in Server Prefs/WGM can't post to their blogs, comment, create wiki pages... They can't do anything! There's log from Wiki errors (when user DURAK tries to create new blog entry): [HTTPChannel,5,127.0.0.1] Traceback (most recent call last): [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/web/server.py", line 126, in process self.render(resrc) [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/web/server.py", line 133, in render body = resrc.render(self) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_xmlrpc_server/WebAppServer.py", line 90, in render d = defer.maybeDeferred(function, *args) [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/internet/defer.py", line 104, in maybeDeferred result = f(*args, **kw) [HTTPChannel,5,127.0.0.1] --- <exception caught here> --- [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_xmlrpc_server/ContentServiceBase.py", line 121, in xmlrpc_addEntry aPage = ContentEntry.newBundleBasedContentEntry (path = path, content = content, author = author, title = title, uid = uid, type = kind, versioned = self.versioned, templateName = template) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_wlt/ContentEntry.py", line 794, in newBundleBasedContentEntry aPage.save('First created', 'created') [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_wlt/ContentEntry.py", line 445, in save revisions.addRevision(self.serializeEntry(revisionAttributes), inComment = comment, inAuthor = updateAuthor, inChangeType = editType) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_utilities/sqlitersion.py", line 36, in _func result = f(self, *args, **kwargs) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_utilities/sqlitersion.py", line 49, in addRevision contentPlistStr = plistlib.writePlistToString(inContentDict).decode("utf-8") [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 110, in writePlistToString [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 94, in writePlist [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 251, in writeValue [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 280, in writeDict [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 238, in writeValue [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 171, in simpleElement [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 221, in _escapeAndEncode [HTTPChannel,5,127.0.0.1] exceptions.UnicodeDecodeError: 'ascii' codec can't decode byte 0xd0 in position 0: ordinal not in range(128) [HTTPChannel,5,127.0.0.1] 'Unparseable html in page, removing whatever was already written.' [HTTPChannel,5,127.0.0.1] Removing /Library/Collaboration/Users/durak/weblog/27133.page Any "old" user CAN create, modify, comment, etc. What can you recommend to fix this issue? Hope for your help...

  Read the article

• SSL connection error during handshake on Windows Server 2008 R2

  - by Thomas

  I have a Windows 2008 R2 Server that runs a HTTPS Tunneling service. The software uses a certificate that is provided via the Windows certificate store. The certificate is located in the local computer private certificates. It supports server and client authentication with signing and keyencipherment. Cert chain The certificate chain looks fine. It's a Thawte SSL123 certificate. Thawte Premium Server CA (SHA1) [?e0 ab 05 94 20 72 54 93 05 60 62 02 36 70 f7 cd 2e fc 66 66] thawte Primary Root CA [?1f a4 90 d1 d4 95 79 42 cd 23 54 5f 6e 82 3d 00 00 79 6e a2] Thawte DV SSL CA [3c a9 58 f3 e7 d6 83 7e 1c 1a cf 8b 0f 6a 2e 6d 48 7d 67 62] Server certificate Issues Most browsers accept the certificate without any warning. But IE 7 on Windows XP SP3 and Opera 12 on OSX just report an connection error. Opera complains: Secure connection: fatal error (552) https://www.example.com/ Opera was not able to connect to the server, because the server does not communicate via any secure protocol known to Opera. A connection test using openssl s_client -connect www.example.com:443 -state says: CONNECTED(00000003) SSL_connect:before/connect initialization SSL_connect:SSLv2/v3 write client hello A 52471:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:/SourceCache/OpenSSL098/OpenSSL098-35.1/src/ssl/s23_lib.c:182: ssldump -aAHd host www.example.com during curl https://www.example.com/ reports: New TCP connection #1: localhost(53302) <-> www.example.com(443) 1 1 0.0235 (0.0235) C>SV3.1(117) Handshake ClientHello Version 3.1 random[32]= 50 77 56 29 e8 23 82 3b 7f e0 ae 2d c1 31 cb ac 38 01 31 85 4f 91 39 c1 04 32 a6 68 25 cd a0 c1 cipher suites Unknown value 0x39 Unknown value 0x38 Unknown value 0x35 TLS_DHE_RSA_WITH_3DES_EDE_CBC_SHA TLS_DHE_DSS_WITH_3DES_EDE_CBC_SHA TLS_RSA_WITH_3DES_EDE_CBC_SHA Unknown value 0x33 Unknown value 0x32 Unknown value 0x2f Unknown value 0x9a Unknown value 0x99 Unknown value 0x96 TLS_RSA_WITH_RC4_128_SHA TLS_RSA_WITH_RC4_128_MD5 TLS_DHE_RSA_WITH_DES_CBC_SHA TLS_DHE_DSS_WITH_DES_CBC_SHA TLS_RSA_WITH_DES_CBC_SHA TLS_DHE_RSA_EXPORT_WITH_DES40_CBC_SHA TLS_DHE_DSS_EXPORT_WITH_DES40_CBC_SHA TLS_RSA_EXPORT_WITH_DES40_CBC_SHA TLS_RSA_EXPORT_WITH_RC2_CBC_40_MD5 TLS_RSA_EXPORT_WITH_RC4_40_MD5 Unknown value 0xff compression methods unknown value NULL 1 0.0479 (0.0243) S>C TCP FIN 1 0.0481 (0.0002) C>S TCP FIN Thawte provides two Java based SSL Checkers. The Legacy Thawte SSL Certificate Installation Checker and the sslToolBox. Both validate the certificate under Windows XP but report connection errors under OSX and Windows 2008 R2.

  Read the article

• Server 2008/Windows 7/Samba Unspecified error 80004005

  - by ancillary

  I have a Samba share on a LAN with 2008 PDC/DNS. Smb authenticates with AD and I have several Win7 Machines that can connect fine. I recently added a couple of new computers to the LAN which were imaged the same way (same software, etc.; different hardware so different drivers) as the other machines and they have the same policies set. I can not get the new machines to connect to the samba share no matter what. I am always met with either Unspecified Error 0x80004005 or Network Path not found. I've turned off the firewall; set LANMAN auth to respond to NTLM only/send LM & NTLM responses/use NTLM session security if negotiated in Local Sec Policy SEcurity Options; tried both ip and hostname to connect. SMB log shows that authentication succeeds; but then connection is immediately killed by the client. tcpdump shows nothing remarkable except that when trying to connect from the client via hostname there is an unknown packet type error: ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) Here's a couple of lines from that error: 11:18:37.964991 IP 001-client.domain.local.49372 > smb.domain.local.netbios-ssn: P 1670:2146(476) ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) [000] AA 46 96 FA D5 99 33 75 0C C4 20 CE 26 42 F3 61 \252F\226\372\325\2313u \014\304 \316&B\363a [010] F0 8C FB 65 18 17 40 A5 DB 42 BB 94 37 53 92 EC \360\214\373e\030\027@\245 \333B\273\2247S\222\354 [020] 55 98 7F C4 AE 3D 6B 10 C4 U\230\177\304\256=k\020 \304 11:18:37.964998 IP smb.domain.local.netbios-ssn > 001-client.domain.local.49372: . ack 2146 win 100 Here's smb.conf just in case (though don't see how if other machines are working fine): [global] workgroup = MYDOMAIN realm = MYDOMAIN.LOCAL server string = domain|smb share interfaces = eth1 security = ADS password server = 192.168.1.3 log level = 2 log file = /var/log/samba/%m.log smb ports = 139 strict locking = no load printers = No local master = No domain master = No wins server = 192.168.1.3 wins support = Yes idmap uid = 500-10000000 idmap gid = 500-10000000 winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes [samba-share1] comment = SMB Share path = /home/share/smb/ valid users = @"MYDOMAIN+Domain Users" admin users = @"MYDOMAIN+Domain Admins" guest ok = no read only = No create mask = 0765 force directory mode = 0777 Any ideas what else I could try or look for? Or what might be the problem? Thanks.

  Read the article

• Can't ping Ip over bridge

  - by tmn29a

  I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet 172.30.xxx.xxx to be used for KVM-Guests. ifconfig : bond0 Link encap:Ethernet HWaddr e4:11:5b:d4:94:30 inet addr:10.54.2.84 Bcast:10.54.2.127 Mask:255.255.255.192 inet6 addr: fe80::e611:5bff:fed4:9430/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:34277 errors:0 dropped:0 overruns:0 frame:0 TX packets:18379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2638709 (2.5 MiB) TX bytes:2887894 (2.7 MiB) br0 Link encap:Ethernet HWaddr f2:fc:4d:7f:15:f0 inet addr:172.30.254.66 Bcast:172.30.254.127 Mask:255.255.255.192 inet6 addr: fe80::f0fc:4dff:fe7f:15f0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:252 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:10800 (10.5 KiB) Pings : ping -I br0 172.30.xxx.65 PING 172.30.xxx.65 (172.30.xxx.65) from 172.30.xxx.66 br0: 56(84) bytes of data. --- 172.30.xxx.65 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2017ms ping -I bond0 172.30.254.65 PING 172.30.xxx.65 (172.30.xxx.65) from 10.54.2.84 bond0: 56(84) bytes of data. 64 bytes from 172.30.x.65: icmp_req=1 ttl=64 time=0.599 ms 64 bytes from 172.30.x.65: icmp_req=2 ttl=64 time=0.575 ms 64 bytes from 172.30.x.65: icmp_req=3 ttl=64 time=0.565 ms --- 172.30.x.65 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.565/0.579/0.599/0.031 ms Route : Destination Gateway Genmask Flags Metric Ref Use Iface 172.30.x.64 * 255.255.255.192 U 0 0 0 br0 10.54.x.64 * 255.255.255.192 U 0 0 0 bond0 default 10.54.x.65 0.0.0.0 UG 0 0 0 bond0 default 172.30.x.65 0.0.0.0 UG 0 0 0 br0 The Interface : cat /etc/network/interfaces auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.54.x.84 netmask 255.255.255.192 network 10.54.x.64 gateway 10.54.x.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports bond0 address 172.30.x.66 broadcast 172.30.x.127 netmask 255.255.x.192 gateway 172.30.x.65 bridge_maxwait 0 If you need more info please ask. Thanks for your help !

  Read the article

• Undelivered Mail Returned to Sender

  - by Alex

  When sending to [email protected] via PHP mail() function, I receive mails. When sending emails from external machines, I receive the following (e.g., sending from [email protected]. [mail.ru is Russian gmail]): This is the mail system at host fallback2.mail.ru. I'm sorry to have to inform you that your message could not be delivered to one or more recipients. It's attached below. For further assistance, please send mail to <postmaster> If you do so, please include this problem report. You can delete your own text from the attached returned message. The mail system <[email protected]>: lost connection with mail.mydomain.com[xxx.xxx.xxx.xxx] while receiving the initial server greeting Reporting-MTA: dns; fallback2.mail.ru X-mPOP-Fallback_MX-Queue-ID: D8C19F2411F1 X-mPOP-Fallback_MX-Sender: rfc822; [email protected] Arrival-Date: Tue, 29 Oct 2013 10:09:21 +0400 (MSK) Final-Recipient: rfc822; [email protected] Original-Recipient: rfc822;[email protected] Action: failed Status: 4.4.2 Diagnostic-Code: X-mPOP-Fallback_MX; lost connection with mail.tld.com[xxx.xxx.xxx.xxx] while receiving the initial server greeting Here is my postfix main.cf: command_directory = /usr/sbin daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix myhostname = mail.mydomain.com mydomain = mydomain.com myorigin = mydomain.com inet_interfaces = all inet_protocols = all unknown_local_recipient_reject_code = 550 in_flow_delay = 1s alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases mail_name = mydomain.com daemon debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin ddd $daemon_directory/$process_name $process_id & sleep 5 sendmail_path = /usr/sbin/sendmail.postfix newaliases_path = /usr/bin/newaliases.postfix mailq_path = /usr/bin/mailq.postfix setgid_group = postdrop html_directory = no manpage_directory = /usr/share/man sample_directory = /usr/share/doc/postfix-2.6.6/samples readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES bounce_queue_lifetime = 4h maximal_queue_lifetime = 4h delay_warning_time = 1h strict_rfc821_envelopes = yes show_user_unknown_table_name = no allow_percent_hack = no swap_bangpath = no smtpd_delay_reject = yes smtpd_error_sleep_time = 20 smtpd_soft_error_limit = 1 smtpd_hard_error_limit = 3 smtpd_junk_command_limit = 2 mydestination = mydomain.com, localhost.localdomain, localhost smtpd_client_restrictions = permit_inet_interfaces smtpd_recipient_limit = 100 virtual_alias_domains = mydomain.com virtual_alias_maps = hash:/etc/postfix/virtual smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smtpd_sasl_auth_enable = yes smtpd_relay_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination Why emails from external server are not being delivered? Thank you! Update In a log, the following lines appear a lot of times Oct 30 10:48:29 mydomain postfix/smtpd[16216]: connect from fallback5.mail.ru[94.100.176.59] Oct 30 10:48:29 mydomain postfix/smtpd[16216]: warning: SASL: Connect to private/auth failed: Connection refused Oct 30 10:48:29 mydomain postfix/smtpd[16216]: fatal: no SASL authentication mechanisms It appears I have to configure SASL? I would understand if I would like to send emails from postfix, but why do I need it to receive emails?

  Read the article

• How to replace for-loops with a functional statement in C#?

  - by Lernkurve

  A colleague once said that God is killing a kitten every time I write a for-loop. When asked how to avoid for-loops, his answer was to use a functional language. However, if you are stuck with a non-functional language, say C#, what techniques are there to avoid for-loops or to get rid of them by refactoring? With lambda expressions and LINQ perhaps? If so, how? Questions So the question boils down to: Why are for-loops bad? Or, in what context are for-loops to avoid and why? Can you provide C# code examples of how it looks before, i.e. with a loop, and afterwards without a loop?

  Read the article

• Token based Authentication for WCF HTTP/REST Services: Authentication

  - by Your DisplayName here!

  This post shows some of the implementation techniques for adding token and claims based security to HTTP/REST services written with WCF. For the theoretical background, see my previous post. Disclaimer The framework I am using/building here is not the only possible approach to tackle the problem. Based on customer feedback and requirements the code has gone through several iterations to a point where we think it is ready to handle most of the situations. Goals and requirements The framework should be able to handle typical scenarios like username/password based authentication, as well as token based authentication The framework should allow adding new supported token types Should work with WCF web programming model either self-host or IIS hosted Service code can rely on an IClaimsPrincipal on Thread.CurrentPrincipal that describes the client using claims-based identity Implementation overview In WCF the main extensibility point for this kind of security work is the ServiceAuthorizationManager. It gets invoked early enough in the pipeline, has access to the HTTP protocol details of the incoming request and can set Thread.CurrentPrincipal. The job of the SAM is simple: Check the Authorization header of the incoming HTTP request Check if a “registered” token (more on that later) is present If yes, validate the token using a security token handler, create the claims principal (including claims transformation) and set Thread.CurrentPrincipal If no, set an anonymous principal on Thread.CurrentPrincipal. By default, anonymous principals are denied access – so the request ends here with a 401 (more on that later). To wire up the custom authorization manager you need a custom service host – which in turn needs a custom service host factory. The full object model looks like this: Token handling A nice piece of existing WIF infrastructure are security token handlers. Their job is to serialize a received security token into a CLR representation, validate the token and turn the token into claims. The way this works with WS-Security based services is that WIF passes the name/namespace of the incoming token to WIF’s security token handler collection. This in turn finds out which token handler can deal with the token and returns the right instances. For HTTP based services we can do something very similar. The scheme on the Authorization header gives the service a hint how to deal with an incoming token. So the only missing link is a way to associate a token handler (or multiple token handlers) with a scheme and we are (almost) done. WIF already includes token handler for a variety of tokens like username/password or SAML 1.1/2.0. The accompanying sample has a implementation for a Simple Web Token (SWT) token handler, and as soon as JSON Web Token are ready, simply adding a corresponding token handler will add support for this token type, too. All supported schemes/token types are organized in a WebSecurityTokenHandlerCollectionManager and passed into the host factory/host/authorization manager. Adding support for basic authentication against a membership provider would e.g. look like this (in global.asax): var manager = new WebSecurityTokenHandlerCollectionManager(); manager.AddBasicAuthenticationHandler((username, password) => Membership.ValidateUser(username, password));   Adding support for Simple Web Tokens with a scheme of Bearer (the current OAuth2 scheme) requires passing in a issuer, audience and signature verification key: manager.AddSimpleWebTokenHandler(     "Bearer",     "http://identityserver.thinktecture.com/trust/initial",     "https://roadie/webservicesecurity/rest/",     "WFD7i8XRHsrUPEdwSisdHoHy08W3lM16Bk6SCT8ht6A="); In some situations, SAML token may be used as well. The following configures SAML support for a token coming from ADFS2: var registry = new ConfigurationBasedIssuerNameRegistry(); registry.AddTrustedIssuer( "d1 c5 b1 25 97 d0 36 94 65 1c e2 64 fe 48 06 01 35 f7 bd db", "ADFS"); var adfsConfig = new SecurityTokenHandlerConfiguration(); adfsConfig.AudienceRestriction.AllowedAudienceUris.Add( new Uri("https://roadie/webservicesecurity/rest/")); adfsConfig.IssuerNameRegistry = registry; adfsConfig.CertificateValidator = X509CertificateValidator.None; // token decryption (read from config) adfsConfig.ServiceTokenResolver = IdentityModelConfiguration.ServiceConfiguration.CreateAggregateTokenResolver();             manager.AddSaml11SecurityTokenHandler("SAML", adfsConfig);   Transformation The custom authorization manager will also try to invoke a configured claims authentication manager. This means that the standard WIF claims transformation logic can be used here as well. And even better, can be also shared with e.g. a “surrounding” web application. Error handling A WCF error handler takes care of turning “access denied” faults into 401 status codes and a message inspector adds the registered authentication schemes to the outgoing WWW-Authenticate header when a 401 occurs. The next post will conclude with authorization as well as the source code download.   (Wanna learn more about federation, WIF, claims, tokens etc.? Click here.)

  Read the article

• Configure IPv6 on your Linux system (Ubuntu)

  After the presentation on IPv6 at the first event of the Emtel Knowledge Series and some recent discussion on social media networks with other geeks and Linux interested IT people here in Mauritius, I thought that I should give it a try (finally) and tweak my local network infrastructure. Honestly, I have been to busy with contractual project work and it never really occurred to me to set up IPv6 in my LAN. Well, the following paragraphs are going to shed some light on those aspects of modern computer and network technology. This is the first article in a series on IPv6 configuration: Configure IPv6 on your Linux system DHCPv6: Provide IPv6 information in your local network Enabling DNS for IPv6 infrastructure Accessing your web server via IPv6 Piece of advice: This is based on my findings on the internet while reading other people's helpful articles and going through a couple of man-pages on my local system. Let's embrace IPv6 The basic configuration on Linux is actually very simple as the kernel, operating system, and user-space programs support that protocol natively. If your system is ready to go for IP (aka: IPv4), then you are good to go for anything else. At least, I didn't have to install any additional packages on my system(s). We are going to assign a static IPv6 address to the system. Hence, we have to modify the definition of interfaces and check whether we have an inet6 entry specified. Open your favourite text editor and check the following entries (it should be at least similar to this): $ sudo nano /etc/network/interfaces auto eth0# IPv4 configurationiface eth0 inet static  address 192.168.1.2  network 192.168.1.0  netmask 255.255.255.0  broadcast 192.168.1.255# IPv6 configurationiface eth0 inet6 static  pre-up modprobe ipv6  address 2001:db8:bad:a55::2  netmask 64 Of course, you might have to adjust your interface device (eth0) or you might be interested to have multiple directives for additional devices (eth1, eth2, etc.). The auto instruction takes care that your device is enabled and configured during the booting phase. The use of the pre-up directive depends on your kernel configuration but in most scenarios this might be an optional line. Anyways, it doesn't hurt to have it enabled after all - just to be on the safe side. Next, either restart your network subsystem like so: $ sudo service networking restart Or you might prefer to do it manually with identical parameters, like so: $ sudo ifconfig eth0 inet6 add 2001:db8:bad:a55::2/64 In case that you're logged in remotely into your PC (ie. via ssh), it is highly advised to opt for the second choice and add the device manually. You can check your configuration afterwards with one of the following commands (depends on whether it is installed): $ sudo ifconfig eth0eth0      Link encap:Ethernet  HWaddr 00:21:5a:50:d7:94            inet addr:192.168.160.2  Bcast:192.168.160.255  Mask:255.255.255.0          inet6 addr: fe80::221:5aff:fe50:d794/64 Scope:Link          inet6 addr: 2001:db8:bad:a55::2/64 Scope:Global          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 $ sudo ip -6 address show eth03: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000    inet6 2001:db8:bad:a55::2/64 scope global        valid_lft forever preferred_lft forever    inet6 fe80::221:5aff:fe50:d794/64 scope link        valid_lft forever preferred_lft forever In both cases, it confirms that our network device has been assigned a valid IPv6 address. That's it in general for your setup on one system. But of course, you might be interested to enable more services for IPv6, especially if you're already running a couple of them in your IP network. More details are available on the official Ubuntu Wiki. Continue to configure your network to provide IPv6 address information automatically in your local infrastructure.

  Read the article

• Wireless not working on Dell XPS 17 after installing 12.04

  - by user60622

  I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

  Read the article

• Unable to keep the connecting using a wireless bridge

  - by dan

  I am running Ubuntu 12.04 on a dell inspiron desktop (core 2 duo) and am using wicd to manage my network/wifi. I've found that the WiFi card in the machine has trouble staying connected to my router (I believe this is a function of distance between the two), so I've taken an old Belkin F5d7231 wireless router and installed dd-wrt on it to use as a wireless bridge hoping that it will have better reception. I think everything up through the wireless bridge is working OK since I have no problems accessing the internet through it with my MacBook. The problem arises when I try to hook the ubuntu machine up to the wireless bridge. It will connect for a few minutes, but it will quickly disconnect without clear triggering event; it may be more likely to disconnect if there is a heavy traffic load going over it (could be something as simple as "cat big_text_file" in an ssh session). I've tried switching from dhclient to dhcpcd without much improvement. Here is the output from the syslog when it connects: Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: exiting Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: exiting Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:10:08 Chicabuntu kernel: [15184.976127] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.010805] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: exiting Jun 30 17:10:08 Chicabuntu kernel: [15185.180156] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.212785] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:10 Chicabuntu kernel: [15187.027445] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:10:10 Chicabuntu kernel: [15187.027452] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:10:10 Chicabuntu kernel: [15187.028300] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: dhcpcd 3.2.3 starting Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: hardware address = 00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: DUID = 00:01:00:01:17:81:85:79:00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: broadcasting for a lease Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:10:20 Chicabuntu kernel: [15197.568016] eth0: no IPv6 routers present Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: offered 192.168.1.111 from 192.168.1.254 Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: checking 192.168.1.111 is available on attached networks Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: leased 192.168.1.111 for 86400 seconds Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding IP address 192.168.1.111/24 Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding default route via 192.168.1.254 metric 0 Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: exiting Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv4 for mDNS. Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Registering new address record for 192.168.1.111 on eth0.IPv4. Jun 30 17:10:30 Chicabuntu dhcpcd.sh: interface eth0 has been configured with new IP=192.168.1.111 Jun 30 17:10:39 Chicabuntu ntpdate[28439]: adjust time server 91.189.94.4 offset 0.001915 sec And here is the syslog from when it shuts down the connection without reason: Jun 30 17:12:15 Chicabuntu kernel: [15312.575455] tg3 0000:3f:00.0: eth0: Link is down Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: sending signal 1 to pid 28361 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: received SIGHUP, releasing lease Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: exiting Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for 192.168.1.111 on eth0. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing default route via 192.168.1.254 metric 0 Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: No such process Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing IP address 192.168.1.111/24 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: Cannot assign requested address Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: exiting Jun 30 17:12:16 Chicabuntu dhcpcd.sh: interface eth0 has been brought down Jun 30 17:12:17 Chicabuntu kernel: [15313.612141] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.644703] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: exiting Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: exiting Jun 30 17:12:17 Chicabuntu kernel: [15313.912147] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.944746] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:18 Chicabuntu kernel: [15315.592569] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:12:18 Chicabuntu kernel: [15315.592576] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:12:18 Chicabuntu kernel: [15315.593399] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:12:29 Chicabuntu kernel: [15325.680019] eth0: no IPv6 routers present If this isn't useful, I can also post the wicd log, but that is kind of long. If anyone could help me I would be eternally grateful.

  Read the article

• Best Practices Generating WebService Proxies for Oracle Sales Cloud (Fusion CRM)

  - by asantaga

  I've recently been building a REST Service wrapper for Oracle Sales Cloud and initially all was going well, however as soon as I added all of my Web Service proxies I started to get weird errors..  My project structure looks like this What I found out was if I only had the InteractionsService & OpportunityService WebService Proxies then all worked ok, but as soon as I added the LocationsService Proxy, I would start to see strange JAXB errors. Example of the error message Exception in thread "main" javax.xml.ws.WebServiceException: Unable to create JAXBContextat com.sun.xml.ws.model.AbstractSEIModelImpl.createJAXBContext(AbstractSEIModelImpl.java:164)at com.sun.xml.ws.model.AbstractSEIModelImpl.postProcess(AbstractSEIModelImpl.java:94)at com.sun.xml.ws.model.RuntimeModeler.buildRuntimeModel(RuntimeModeler.java:281)at com.sun.xml.ws.client.WSServiceDelegate.buildRuntimeModel(WSServiceDelegate.java:762)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate.buildRuntimeModel(WLSProvider.java:982)at com.sun.xml.ws.client.WSServiceDelegate.createSEIPortInfo(WSServiceDelegate.java:746)at com.sun.xml.ws.client.WSServiceDelegate.addSEI(WSServiceDelegate.java:737)at com.sun.xml.ws.client.WSServiceDelegate.getPort(WSServiceDelegate.java:361)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate.internalGetPort(WLSProvider.java:934)at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate$PortClientInstanceFactory.createClientInstance(WLSProvider.java:1039)...... Looking further down I see the error message is related to JAXB not being able to find an objectFactory for one of its types Caused by: java.security.PrivilegedActionException: com.sun.xml.bind.v2.runtime.IllegalAnnotationsException: 6 counts of IllegalAnnotationExceptionsThere's no ObjectFactory with an @XmlElementDecl for the element {http://xmlns.oracle.com/apps/crmCommon/activities/activitiesService/}AssigneeRsrcOrgIdthis problem is related to the following location:at protected javax.xml.bind.JAXBElement com.oracle.xmlns.apps.crmcommon.activities.activitiesservice.ActivityAssignee.assigneeRsrcOrgId at com.oracle.xmlns.apps.crmcommon.activities.activitiesservice.ActivityAssignee This is very strange... My first thoughts are that when I generated the WebService Proxy I entered the package name as "oracle.demo.pts.fusionproxy.servicename" and left the generated types as blank. This way all the generated types get put into the same package hierarchy and when deployed they get merged... Sounds resaonable and appears to work but not in this case..  To resolve this I regenerate the proxy but this time setting : Package name : To the name of my package eg. oracle.demo.pts.fusionproxy.interactionsRoot Package for Generated Types :  Package where the types will be generated to, e.g. oracle.demo.pts.fusionproxy.SalesParty.types When I ran the application now, it all works , awesome eh???? Alas no, there is a serious side effect. The problem now is that to help coding I've created a collection of helper classes , these helper classes take parameters which use some of the "generic" datatypes, like FindCriteria. e.g. This wont work any more public static FindCriteria createCustomFindCriteria(FindCriteria pFc,String pAttributes) Here lies a gremlin of a problem.. I cant use this method anymore, this is because the FindCriteria datatype is now being defined two, or more times, in the generated code for my project. If you leave the Root Package for types blank it will get generated to com.oracle.xmlns, and if you populate it then it gets generated to your custom package.. The two datatypes look the same, sound the same (and if this were a duck would sound the same), but THEY ARE NOT THE SAME... Speaking to development, they recommend you should not be entering anything in the Root Packages section, so the mystery thickens why does it work.. Well after spending sometime with some colleagues of mine in development we've identified the issue.. Alas different parts of Oracle Fusion Development have multiple schemas with the same namespace, when the WebService generator generates its classes its not seeing the other schemas properly and not generating the Object Factories correctly...  Thankfully I've found a workaround Solution Overview When generating the proxies leave the Root Package for Generated Types BLANK When you have finished generating your proxies, use the JAXB tool XJC and generate Java classes for all datatypes  Create a project within your JDeveloper11g workspace and import the java classes into this project Final bit.. within the project dependencies ensure that the JAXB/XJC generated classes are "FIRST" in the classpath Solution Details Generate the WebServices SOAP proxies When generating the proxies your generation dialog should look like this Ensure the "unwrap" parameters is selected, if it isn't then that's ok, it simply means when issuing a "get" you need to extract out the Element Generate the JAXB Classes using XJC XJC provides a command line switch called -wsdl, this (although is experimental/beta) , accepts a HTTP WSDL and will generate the relevant classes. You can put these into a single batch/shell script xjc -wsdl https://fusionservername:443/appCmmnCompInteractions/InteractionService?wsdlxjc -wsdl https://fusionservername443/opptyMgmtOpportunities/OpportunityService?wsdl Create Project in JDeveloper to store the XJC "generated" JAXB classes Within the project folder create a filesystem folder called "src" and copy the generated files into this folder. JDeveloper11g should then see the classes and display them, if it doesnt try clicking the "refresh" button In your main project ensure that the JDeveloper XJC project is selected as a dependancy and IMPORTANT make sure it is at the top of the list. This ensures that the classes are at the front of the classpath And voilà.. Hopefully you wont see any JAXB generation errors and you can use common datatypes interchangeably in your project, (e.g. FindCriteria etc)

  Read the article

• W7 routing - traffic not going to default gateway

  - by Ian Macintosh

  I have a really strange Windows 7 IPv4 routing issue that I can't get to the bottom of. The summary of the issue is that the default gateway is set to 192.168.254.253, but that it is actually using a default gateway of 192.168.254.254. Here's a network diagram: .-,( ),-. .-( )-. .-----( internet )----.--------------------------. | '-( ).-' | | | '-.( ).-' | | v v v .------------. .------. .------. | 10mb Fibre | | ADSL | | ADSL | '------------' '------' '------' | | | | | | v v v .---------------------. .--------------------. .--------------------. | Juniper Box | | Draytek DSL Router | | Draytek DSL Router | |---------------------| |--------------------| |--------------------| | (public IP address) | | 172.16.0.x | | 172.16.0.x | '---------------------' '--------------------' '--------------------' | | | | | .-------------------' | v v v .-------------------------. .-----------------. | Draytek Dual WAN Router | | Untangle GW | |-------------------------| |-----------------| | 192.168.254.254 | | 192.168.254.253 | '-------------------------' '-----------------' | | | | | v v =================================== LAN =================================== | | | | v v .----------------. .----------------. | Windows 7 W/S | | Windows 7 W/S | |----------------| |----------------| | 192.168.254.38 | | 192.168.254.77 | '----------------' '----------------' This is a recently (a few weeks ago) converted fibre site with the original 2 DSL lines still attached and running. An Untangle (firewall) was installed with the fibre line. Here is the affected PC network configuration: C:\>ipconfig /allcompartments /all Windows IP Configuration ============================================================================== Network Information for Compartment 1 (ACTIVE) ============================================================================== Host Name . . . . . . . . . . . . : COMP36 Primary Dns Suffix . . . . . . . : XXXXXX.local Node Type . . . . . . . . . . . . : Broadcast IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : XXXXXX.local Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : XXXXXX.local Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : C8-9C-DC-33-F1-65 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::3925:86a5:7066:ab92%15(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.254.38(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 22 August 2012 10:20:32 Lease Expires . . . . . . . . . . : 30 August 2012 10:20:31 Default Gateway . . . . . . . . . : 192.168.254.253 DHCP Server . . . . . . . . . . . : 192.168.254.200 DHCPv6 IAID . . . . . . . . . . . : 315137244 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-4A-17-8D-10-78-D2-74-2F-8A DNS Servers . . . . . . . . . . . : 192.168.254.200 Primary WINS Server . . . . . . . : 192.168.254.200 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter isatap.XXXXXX.local: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : XXXXXX.local Description . . . . . . . . . . . : Microsoft ISATAP Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes The routing table: C:\>route print =========================================================================== Interface List 15...c8 9c dc 33 f1 65 ......Realtek PCIe GBE Family Controller #2 1...........................Software Loopback Interface 1 10...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.254.253 192.168.254.38 10 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.254.0 255.255.255.0 On-link 192.168.254.38 266 192.168.254.38 255.255.255.255 On-link 192.168.254.38 266 192.168.254.255 255.255.255.255 On-link 192.168.254.38 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.254.38 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.254.38 266 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 15 266 fe80::/64 On-link 15 266 fe80::3925:86a5:7066:ab92/128 On-link 1 306 ff00 ::/8 On-link 15 266 ff00::/8 On-link =========================================================================== Persistent Routes: None And the strange routing as demonstrated by tracert: C:\>tracert -d www.bbc.co.uk Tracing route to www.bbc.net.uk [212.58.246.95] over a maximum of 30 hops: 1 1 ms 1 ms <1 ms 192.168.254.254 2 1 ms 1 ms 1 ms 172.16.0.254 3 17 ms 18 ms 16 ms XXXXXXXXXXXXXXX 4 18 ms 19 ms 19 ms XXXXXXXXXXXXXXX 5 22 ms 22 ms 22 ms XXXXXXXXXXXXXXX 6 22 ms 21 ms 22 ms XXXXXXXXXXXXXXX 7 21 ms 21 ms 22 ms 217.41.169.109 8 30 ms 32 ms 57 ms 109.159.251.227 9 46 ms 39 ms 35 ms 109.159.251.137 10 27 ms 66 ms 30 ms 109.159.254.116 ^C However, when done from another Windows 7 workstation: C:\Users\administrator>ipconfig /allcompartments /all Windows IP Configuration ============================================================================== Network Information for Compartment 1 (ACTIVE) ============================================================================== Host Name . . . . . . . . . . . . : PABX-BACKUP Primary Dns Suffix . . . . . . . : XXXXXX.local Node Type . . . . . . . . . . . . : Broadcast IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : XXXXXX.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : XXXXXX.local Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 8C-89-A5-94-43-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9479:1c11:6f9f:ae0b%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.254.77(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 15 August 2012 08:27:18 Lease Expires . . . . . . . . . . : 27 August 2012 08:27:31 Default Gateway . . . . . . . . . : 192.168.254.253 DHCP Server . . . . . . . . . . . : 192.168.254.200 DHCPv6 IAID . . . . . . . . . . . : 244091301 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-C2-79-BE-8C-89-A5-94-43-84 DNS Servers . . . . . . . . . . . : 192.168.254.200 Primary WINS Server . . . . . . . : 192.168.254.200 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter isatap.XXXXXX.local: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : XXXXXX.local Description . . . . . . . . . . . : Microsoft ISATAP Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft 6to4 Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes C:\Users\administrator> And finally, doing a tracert from the 2nd workstation yields expected results: C:\Users\administrator>tracert -d www.bbc.co.uk Tracing route to www.bbc.net.uk [212.58.244.67] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.254.253 2 1 ms 1 ms 1 ms 141.0.xxx.xxx 3 2 ms 2 ms 2 ms 141.0.xxx.xxx 4 7 ms 2 ms 2 ms 109.204.xxx.xxx 5 2 ms 2 ms 2 ms 95.177.0.7 6 3 ms 2 ms 2 ms 95.177.0.9 7 30 ms 2 ms 2 ms 95.177.0.2 8 2 ms 2 ms 2 ms 195.66.224.103 9 ^C As expected, it is routing via .253, and the 2nd hop is the inside interface of the Juniper NTU. I've not inspected the traffic yet. In particular, I was going to look for ICMP redirects, though why there would be an ICMP redirect at all is not really sensible? .254 used to be the default gateway before the fibre was installed. Any ideas? Doesn't make sense to me why there should be this routing issue :( The Draytek Dual WAN Router was rebooted, the PC was rebooted. The PC had the network disabled and then re-enabled. All the standard stuff when Windows looses the plot. Hopefully somebody recognises the symptoms! PS: Sorry for the long post, but I didn't want to leave something potentially relevant out. PPS: No iSCSI involved on/at this or any other workstation so Windows 7 routing traffic through the gateway for local addresses isn't the issue.

  Read the article

• Getting output parameter(SYS_REFCURSOR) from Oracle stored procedure in iBATIS 3(by using annotation

  - by yjacket

  I got an example how to call oracle SP in iBATIS 3 without a map file. And now I understand how to call it. But I got another problem that how to get a result from output parameter(Oracle cursor). A part of exception messages is "There is no setter for property named 'rs' in 'class java.lang.Class". Below is my code. Does anyone can help me? Oracle Stored Procedure: CREATE OR REPLACE PROCEDURE getProducts ( rs OUT SYS_REFCURSOR ) IS BEGIN OPEN rs FOR SELECT * FROM Products; END getProducts; Interface: public interface ProductMapper { @Select("call getProducts(#{rs,mode=OUT,jdbcType=CURSOR})") @Options(statementType = StatementType.CALLABLE) List<Product> getProducts(); } DAO: public class ProductDAO { public List<Product> getProducts() { return mapper.getProducts(); // mapper is ProductMapper } } Full Error Message: Exception in thread "main" org.apache.ibatis.exceptions.IbatisException: ### Error querying database. Cause: org.apache.ibatis.reflection.ReflectionException: Could not set property 'rs' of 'class org.apache.ibatis.reflection.MetaObject$NullObject' with value 'oracle.jdbc.driver.OracleResultSetImpl@1a001ff' Cause: org.apache.ibatis.reflection.ReflectionException: There is no setter for property named 'rs' in 'class java.lang.Class' ### The error may involve defaultParameterMap ### The error occurred while setting parameters ### Cause: org.apache.ibatis.reflection.ReflectionException: Could not set property 'rs' of 'class org.apache.ibatis.reflection.MetaObject$NullObject' with value 'oracle.jdbc.driver.OracleResultSetImpl@1a001ff' Cause: org.apache.ibatis.reflection.ReflectionException: There is no setter for property named 'rs' in 'class java.lang.Class' at org.apache.ibatis.exceptions.ExceptionFactory.wrapException(ExceptionFactory.java:8) at org.apache.ibatis.session.defaults.DefaultSqlSession.selectList(DefaultSqlSession.java:61) at org.apache.ibatis.session.defaults.DefaultSqlSession.selectList(DefaultSqlSession.java:53) at org.apache.ibatis.binding.MapperMethod.executeForList(MapperMethod.java:82) at org.apache.ibatis.binding.MapperMethod.execute(MapperMethod.java:63) at org.apache.ibatis.binding.MapperProxy.invoke(MapperProxy.java:35) at $Proxy8.getList(Unknown Source) at com.dao.ProductDAO.getList(ProductDAO.java:42) at com.Ibatis3Test.main(Ibatis3Test.java:30) Caused by: org.apache.ibatis.reflection.ReflectionException: Could not set property 'rs' of 'class org.apache.ibatis.reflection.MetaObject$NullObject' with value 'oracle.jdbc.driver.OracleResultSetImpl@1a001ff' Cause: org.apache.ibatis.reflection.ReflectionException: There is no setter for property named 'rs' in 'class java.lang.Class' at org.apache.ibatis.reflection.wrapper.BeanWrapper.setBeanProperty(BeanWrapper.java:154) at org.apache.ibatis.reflection.wrapper.BeanWrapper.set(BeanWrapper.java:36) at org.apache.ibatis.reflection.MetaObject.setValue(MetaObject.java:120) at org.apache.ibatis.executor.resultset.FastResultSetHandler.handleOutputParameters(FastResultSetHandler.java:69) at org.apache.ibatis.executor.statement.CallableStatementHandler.query(CallableStatementHandler.java:44) at org.apache.ibatis.executor.statement.RoutingStatementHandler.query(RoutingStatementHandler.java:55) at org.apache.ibatis.executor.SimpleExecutor.doQuery(SimpleExecutor.java:41) at org.apache.ibatis.executor.BaseExecutor.query(BaseExecutor.java:94) at org.apache.ibatis.executor.CachingExecutor.query(CachingExecutor.java:72) at org.apache.ibatis.session.defaults.DefaultSqlSession.selectList(DefaultSqlSession.java:59) ... 7 more Caused by: org.apache.ibatis.reflection.ReflectionException: There is no setter for property named 'rs' in 'class java.lang.Class' at org.apache.ibatis.reflection.Reflector.getSetInvoker(Reflector.java:300) at org.apache.ibatis.reflection.MetaClass.getSetInvoker(MetaClass.java:97) at org.apache.ibatis.reflection.wrapper.BeanWrapper.setBeanProperty(BeanWrapper.java:146) ... 16 more

  Read the article

• Unauthorized Sharepoint WSDL from Coldfusion 8

  - by antony.trupe

  How do I solve the error: Unable to read WSDL from URL: https://workflowtest.site.edu/_vti_bin/Lists.asmx?WSDL. Error: 401 Unauthorized. I can successfully view the WSDL from the browser using the same user account. I'm not sure which authentication is being used (Basic or Integrated). How would I find that out? The code making the call is: <cfinvoke username="username" password="password" webservice="https://workflowtest.liberty.edu/_vti_bin/Lists.asmx?WSDL" method="GetList" listName="{CB02EB71-392E-4906-B512-8EC002F72436}" > The impression I get is that coldfusion doesn't like being made to authenticate to get the WSDL. Full stack trace: coldfusion.xml.rpc.XmlRpcServiceImpl$CantFindWSDLException: Unable to read WSDL from URL: https://workflowtest.liberty.edu/_vti_bin/Lists.asmx?WSDL. at coldfusion.xml.rpc.XmlRpcServiceImpl.retrieveWSDL(XmlRpcServiceImpl.java:709) at coldfusion.xml.rpc.XmlRpcServiceImpl.access$000(XmlRpcServiceImpl.java:53) at coldfusion.xml.rpc.XmlRpcServiceImpl$1.run(XmlRpcServiceImpl.java:239) at java.security.AccessController.doPrivileged(Native Method) at coldfusion.xml.rpc.XmlRpcServiceImpl.registerWebService(XmlRpcServiceImpl.java:232) at coldfusion.xml.rpc.XmlRpcServiceImpl.getWebService(XmlRpcServiceImpl.java:496) at coldfusion.xml.rpc.XmlRpcServiceImpl.getWebServiceProxy(XmlRpcServiceImpl.java:450) at coldfusion.tagext.lang.InvokeTag.doEndTag(InvokeTag.java:413) at coldfusion.runtime.CfJspPage._emptyTcfTag(CfJspPage.java:2662) at cftonytest2ecfm1787185330.runPage(/var/www/webroot/tonytest.cfm:16) at coldfusion.runtime.CfJspPage.invoke(CfJspPage.java:196) at coldfusion.tagext.lang.IncludeTag.doStartTag(IncludeTag.java:370) at coldfusion.filter.CfincludeFilter.invoke(CfincludeFilter.java:65) at coldfusion.filter.ApplicationFilter.invoke(ApplicationFilter.java:279) at coldfusion.filter.RequestMonitorFilter.invoke(RequestMonitorFilter.java:48) at coldfusion.filter.MonitoringFilter.invoke(MonitoringFilter.java:40) at coldfusion.filter.PathFilter.invoke(PathFilter.java:86) at coldfusion.filter.ExceptionFilter.invoke(ExceptionFilter.java:70) at coldfusion.filter.BrowserDebugFilter.invoke(BrowserDebugFilter.java:74) at coldfusion.filter.ClientScopePersistenceFilter.invoke(ClientScopePersistenceFilter.java:28) at coldfusion.filter.BrowserFilter.invoke(BrowserFilter.java:38) at coldfusion.filter.NoCacheFilter.invoke(NoCacheFilter.java:46) at coldfusion.filter.GlobalsFilter.invoke(GlobalsFilter.java:38) at coldfusion.filter.DatasourceFilter.invoke(DatasourceFilter.java:22) at coldfusion.CfmServlet.service(CfmServlet.java:175) at coldfusion.bootstrap.BootstrapServlet.service(BootstrapServlet.java:89) at jrun.servlet.FilterChain.doFilter(FilterChain.java:86) at coldfusion.monitor.event.MonitoringServletFilter.doFilter(MonitoringServletFilter.java:42) at coldfusion.bootstrap.BootstrapFilter.doFilter(BootstrapFilter.java:46) at jrun.servlet.FilterChain.doFilter(FilterChain.java:94) at jrun.servlet.FilterChain.service(FilterChain.java:101) at jrun.servlet.ServletInvoker.invoke(ServletInvoker.java:106) at jrun.servlet.JRunInvokerChain.invokeNext(JRunInvokerChain.java:42) at jrun.servlet.JRunRequestDispatcher.invoke(JRunRequestDispatcher.java:286) at jrun.servlet.ServletEngineService.dispatch(ServletEngineService.java:543) at jrun.servlet.jrpp.JRunProxyService.invokeRunnable(JRunProxyService.java:203) at jrunx.scheduler.ThreadPool$DownstreamMetrics.invokeRunnable(ThreadPool.java:320) at jrunx.scheduler.ThreadPool$ThreadThrottle.invokeRunnable(ThreadPool.java:428) at jrunx.scheduler.ThreadPool$UpstreamMetrics.invokeRunnable(ThreadPool.java:266) at jrunx.scheduler.WorkerThread.run(WorkerThread.java:66)

  Read the article

• Could not import Django settings into Google App Engine

  - by gkelsall

  Hello all you Google App Engine experts, I have used Django a little before but am new to Google App Engine and am trying to use it's development web server with Django for the first time. I don't know if this is relevent but I previously had Django 1.1 and Python 2.6 on my Windows XP and even though I have uninstalled Python 2.6 there is still a folder and entries in the registry. I have followed the instructions from Google but when I browse to the GAE developemnt web server it cannot find my settings (details below). Any hints gratefully received. Regards Geoff C:\Documents and Settings\GeoffK\My Documents\ing\ingsite>echo %PATH% C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\WINDOWS \system32\WindowsPowerShell\v1.0;;C:\Python25;C:\Python25\Lib\site- packages\django\bin;C:\Documents and Settings\GeoffK\My Documents\ing \ingsite;C:\Program Files\Google\google_appengine\ C:\Documents and Settings\GeoffK\My Documents\ing\ingsite>echo %PYTHONPATH% C:\Documents and Settings\GeoffK\My Documents\ing\ingsite C:\Documents and Settings\GeoffK\My Documents\ing\ingsite>C:\Documents and Settings\GeoffK\My Documents\ing\ingsite>dev_appserver.py -- debug_imports ingiliz\ INFO 2009-08-04 07:29:45,328 appengine_rpc.py:157] Server: appengine.google. com INFO 2009-08-04 07:29:45,358 appcfg.py:322] Checking for updates to the SDK. INFO 2009-08-04 07:29:45,578 appcfg.py:336] The SDK is up to date. WARNING 2009-08-04 07:29:45,578 datastore_file_stub.py:404] Could not read data store data from c:\docume~1\geoffk\locals~1\temp \dev_appserver.datastore WARNING 2009-08-04 07:29:45,578 datastore_file_stub.py:404] Could not read data store data from c:\docume~1\geoffk\locals~1\temp \dev_appserver.datastore.history WARNING 2009-08-04 07:29:45,608 dev_appserver.py:3296] Could not initialize ima ges API; you are likely missing the Python "PIL" module. ImportError: No module named _imaging INFO 2009-08-04 07:29:45,625 dev_appserver_main.py:465] Running application ingiliz on port 8080: http://localhost:8080 ..... Now attempting to browse if need more detail here I can post ..... if not settings.DATABASE_ENGINE: File "C:\Python25\lib\site-packages\django\conf\__init__.py", line 28, in __ge tattr__ self._import_settings() File "C:\Python25\lib\site-packages\django\conf\__init__.py", line 59, in _imp ort_settings self._target = Settings(settings_module) File "C:\Python25\lib\site-packages\django\conf\__init__.py", line 94, in __in it__ raise ImportError, "Could not import settings '%s' (Is it on sys.path? Does it have syntax errors?): %s" % (self.SETTINGS_MODULE, e) ImportError: Could not import settings 'settings' (Is it on sys.path? Does it ha ve syntax errors?): No module named settings INFO 2009-08-04 07:31:02,187 dev_appserver.py:2982] "GET / HTTP/ 1.1" 500 -

  Read the article

• Add animation when user control get visible and collapsed In Wpf

  - by sanjeev40084

  I have two xaml files MainWindow.xaml and other user control WorkDetail.xaml file. MainWindow.xaml file has a textbox, button, listbox and reference to WorkDetail.xaml(user control which is collapsed). Whenever user enter any text, it gets added in listbox when the add button is clicked. When any items from the listbox is double clicked, the visibility of WorkDetail.xaml is set to Visible and it gets displayed. In WorkDetail.xaml (user control) it has textblock and button. The Textblock displays the text of selected item and close button sets the visibility of WorkDetail window to collapsed. Now i am trying to animate WorkDetail.xaml when it gets visible and collapse. When any items from listbox is double clicked and WorkDetail.xaml visibility is set to visible, i want to create an animation of moving WorkDetail.xaml window from right to left on MainWindow. When Close button from WorkDetail.xaml file is clicked and WorkDetail.xaml file is collapsed, i want to slide the WorkDetail.xaml file from left to right from MainWindow. Here is the screenshot: MainWindow.xaml code: <Window...> <Grid Background="Black" > <TextBox x:Name="enteredWork" Height="39" Margin="44,48,49,0" TextWrapping="Wrap" VerticalAlignment="Top"/> <ListBox x:Name="workListBox" Margin="26,155,38,45" FontSize="29.333" MouseDoubleClick="workListBox_MouseDoubleClick"/> <Button x:Name="addWork" Content="Add" Height="34" Margin="71,103,120,0" VerticalAlignment="Top" Click="Button_Click"/> <TestWpf:WorkDetail x:Name="WorkDetail" Visibility="Collapsed"/> </Grid> </Window> MainWindow.xaml.cs class code: namespace TestWpf { public partial class MainWindow : Window { public MainWindow() { this.InitializeComponent(); } private void Button_Click(object sender, RoutedEventArgs e) { workListBox.Items.Add(enteredWork.Text); } private void workListBox_MouseDoubleClick(object sender, MouseButtonEventArgs e) { WorkDetail.workTextBlk.Text = (string)workListBox.SelectedItem; WorkDetail.Visibility = Visibility.Visible; } } } WorkDetail.xaml code: <UserControl ..> <Grid Background="#FFD2CFCF"> <TextBlock x:Name="workTextBlk" Height="154" Margin="33,50,49,0" TextWrapping="Wrap" VerticalAlignment="Top" FontSize="29.333" Background="#FFF13939"/> <Button x:Name="btnClose" Content="Close" Height="62" Margin="70,0,94,87" VerticalAlignment="Bottom" Click="btnClose_Click"/> </Grid> </UserControl> WorkDetail.xaml.cs class code: namespace TestWpf { public partial class WorkDetail : UserControl { public WorkDetail() { this.InitializeComponent(); } private void btnClose_Click(object sender, System.Windows.RoutedEventArgs e) { Visibility = Visibility.Collapsed; } } } Can anyone tell how can i do this?

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >