Search Results

Search found 18897 results on 756 pages for 'network connectivity'.

Page 17/756 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Network unreachable on Ubuntu guest after trying to set up a host only network on Virtualbox

  - by gkb0986

  I have a Mac OS X host and a bunch of guests including Ubuntu and Arch Linux. I was trying to set up a host-only network at eth1 to let me ssh into the system. But now eth0 isn't working properly either. Ubuntu can no longer connect to remote hosts or browse the internet. It tells me that the network is unreachable. What's gone wrong here? I've included some diagnostics below. $ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:10968 errors:0 dropped:0 overruns:0 frame:0 TX packets:10968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:897264 (897.2 KB) TX bytes:897264 (897.2 KB) Other diagnostic commands and the output: $sudo lspci -n 00:00.0 0600: 8086:1237 (rev 02) 00:01.0 0601: 8086:7000 00:01.1 0101: 8086:7111 (rev 01) 00:02.0 0300: 80ee:beef 00:03.0 0200: 8086:100e (rev 02) 00:04.0 0880: 80ee:cafe 00:05.0 0401: 8086:2415 (rev 01) 00:06.0 0C03: 106B:003F 00:07.0 0680: 8086:7113 (REV 08) 00:0D.0 0106: 8086:2829 (REV 02) $sudo lshw -c network *-network DISABLED description: Ethernet interface product: 82540EM Gigabit Ethernet Controller vendor: Intel Corporation physical id: 3 bus info: pci@0000:00:03.0 logical name: eth0 version: 02 serial: 08:00:27:7d:22:df size: 1Gbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm pcix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k8-NAPI duplex=full firmware=N/A latency=64 link=no mingnt=255 multicast=yes port=twisted pair speed=1Gbit/s resources: irq:19 memory:f0000000-f001ffff ioport:d010(size=8) $lsmod Module Size Used by nls_utf8 12557 1 isofs 40257 1 vboxsf 43743 2 vesafb 13844 1 snd_intel8x0 38570 2 snd_ac97_codec 134869 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97275 2 snd_intel8x0,snd_ac97_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi rfcomm 47604 0 snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event bnep 18281 2 bluetooth 180113 10 rfcomm,bnep ppdev 17113 0 psmouse 97519 0 snd_timer 29990 2 snd_pcm,snd_seq joydev 17693 0 snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq vboxvideo 12622 1 serio_raw 13211 0 snd 79041 11 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd vboxguest 235498 7 vboxsf parport_pc 32866 0 drm 241971 2 vboxvideo i2c_piix4 13301 0 snd_page_alloc 18529 2 snd_intel8x0,snd_pcm mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usbhid 47238 0 hid 99636 1 usbhid e1000 108589 0

  Read the article

• Creating an office network and monitoring all activity without a proxy

  - by Robert

  We are setting up our office network and would like to track all the websites visited by our employees. However, we would not like to use any proxy based solutions. Our work is highly dependent on applications in which you cannot configure a proxy. Hence, the approach we would like to follow is setting up a router inside a computer (something like this : http://www.techrepublic.com/article/configure-windows-server-2003-to-act-as-a-router/5844624) This will also allow us to attach multiple ethernet cards and have redundancy in internet connectivity with complete abstraction from the user about which connection is being used. But most importantly, since all the traffic will be going through the computer (configured as a router) I assume there will be a way to run packet analysis on all the request / responses being made. For example, list all the FTP servers connected to (port 21), give a graph of all the URLs visited per day by frequency. Is there already a software which does this ? Or is it possible to build something like this ?

  Read the article

• Multiple interfaces to one IP address?

  - by Delan Azabani

  At present, I have: a Netgear router with DHCP off at 192.168.0.1 my computer eth0 at 192.168.0.2 wlan0 at 192.168.0.2 The wlan0 interface always connects to the router, while the eth0 interface connects to other computers with crossover and acts as a dnsmasq DHCP server for network boot and installation. If I use the Gnome NetworkManager to enable both connections, that is, with wlan0 connected to the router/internet and eth0 to another computer, both as 192.168.0.2, I cannot access the internet while eth0 is connected. Why is this? How can I configure my computer to follow wlan0 for Internet usage, but use eth0 for itself (the latter is working but blocking wlan0).

  Read the article

• Sharing files between multiple computers?

  - by Koalatea

  At my school, we have 13 iMacs that we use to make our yearbook. Currently our school has some servers for us, but since we work with so many files ( thousands of pictures, most of which are ~3MB ) it slows down far too much. Is there a way to better share files between our computers? We are on a wireless network and the whole school shares the same servers, we have around probably 400 computers in the school. Is there a hardware fix I can do? Something like buying an external and hooking only yearbook computers to it?

  Read the article

• Configuring network to set wlan0 as primary

  - by Sheed

  I recently had to rebuild my pc and decided to go for ubuntu 14.04. I think the mistake I made was I started from a 12.04 install disk instead of the 12.10 disk I'd used previously and when given the option set my primary connection as ethernet (because the wireless option didn't work). After upgrading to 14.04 etc, I managed to get the wireless working, or more using steps like ifconfig -a and the likes I managed to prove that the wireless card etc. is all installed and working. However every time I boot without a hard wired connection plugged in I get the message "waiting for network configuration". I can then once it's booted without a network get my wirless working using sudo ifconfig wlan0 up iwlist wlan0 scan This seems to kick the wireless module into life and it appears in the GUI and I can then select a network, however all the options like edit network and disconnect etc are all greyed out. What I would like of course is if the WLAN0 was just set as my primary default network so I've been looking for a solution to this and it would seem that I need to adjust the old /etc/network/interfaces file but when I try to do so using the sudo vi /etc/network/interfaces command I, well I simply have no idea what I'm doing. Other than that typing :q! gets me out of there before I do to much damage! As far as I can tell (by navigating to the file in the GUI) the output of my /etc/network/interfaces is as follows: (obviously not including the " in each line that's just to break the heading rule of the #) "# This file describes the network interfaces available on your system "# and how to activate them. For more information, see interfaces(5). "# The loopback network interface auto lo iface lo inet loopback "# The primary network interface auto eth0 iface eth0 inet dhcp If this is the case then this clearly doesn't contain what it should do but I don't how to fix it. Nor do I even know if I'm on the right track. Any help would be appreciated thanks :)

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  Hi: I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• Network Security [closed]

  - by kapilg

  I have been a .net developer for the past three yrs. Just curious to know about the network security field. What kind of work does the developers working in these area do? I really have not much idea about network security but what my understanding is these people are involved in securing network, preventing attacks on network as obvious. Could any one please give me some details about this field and also what does it take to move to this field.

  Read the article

• Manage SQL Server Connectivity through Windows Azure Virtual Machines Remote PowerShell

  - by SQLOS Team

  Manage SQL Server Connectivity through Windows Azure Virtual Machines Remote PowerShell Blog This blog post comes from Khalid Mouss, Senior Program Manager in Microsoft SQL Server. Overview The goal of this blog is to demonstrate how we can automate through PowerShell connecting multiple SQL Server deployments in Windows Azure Virtual Machines. We would configure TCP port that we would open (and close) though Windows firewall from a remote PowerShell session to the Virtual Machine (VM). This will demonstrate how to take the advantage of the remote PowerShell support in Windows Azure Virtual Machines to automate the steps required to connect SQL Server in the same cloud service and in different cloud services.  Scenario 1: VMs connected through the same Cloud Service 2 Virtual machines configured in the same cloud service. Both VMs running different SQL Server instances on them. Both VMs configured with remote PowerShell turned on to be able to run PS and other commands directly into them remotely in order to re-configure them to allow incoming SQL connections from a remote VM or on premise machine(s). Note: RDP (Remote Desktop Protocol) is kept configured in both VMs by default to be able to remote connect to them and check the connections to SQL instances for demo purposes only; but not actually required. Step 1 – Provision VMs and Configure Ports   Provision VM1; named DemoVM1 as follows (see examples screenshots below if using the portal):   Provision VM2 (DemoVM2) with PowerShell Remoting enabled and connected to DemoVM1 above (see examples screenshots below if using the portal): After provisioning of the 2 VMs above, here is the default port configurations for example: Step2 – Verify / Confirm the TCP port used by the database Engine By the default, the port will be configured to be 1433 – this can be changed to a different port number if desired.   1. RDP to each of the VMs created below – this will also ensure the VMs complete SysPrep(ing) and complete configuration 2. Go to SQL Server Configuration Manager -> SQL Server Network Configuration -> Protocols for <SQL instance> -> TCP/IP - > IP Addresses   3. Confirm the port number used by SQL Server Engine; in this case 1433 4. Update from Windows Authentication to Mixed mode   5.       Restart SQL Server service for the change to take effect 6.       Repeat steps 3., 4., and 5. For the second VM: DemoVM2 Step 3 – Remote Powershell to DemoVM1 Enter-PSSession -ComputerName condemo.cloudapp.net -Port 61503 -Credential <username> -UseSSL -SessionOption (New-PSSessionOption -SkipCACheck -SkipCNCheck) Your will then be prompted to enter the password. Step 4 – Open 1433 port in the Windows firewall netsh advfirewall firewall add rule name="DemoVM1Port" dir=in localport=1433 protocol=TCP action=allow Output: netsh advfirewall firewall show rule name=DemoVM1Port Rule Name:                            DemoVM1Port ---------------------------------------------------------------------- Enabled:                              Yes Direction:                            In Profiles:                             Domain,Private,Public Grouping:                             LocalIP:                              Any RemoteIP:                             Any Protocol:                             TCP LocalPort:                            1433 RemotePort:                           Any Edge traversal:                       No Action:                               Allow Ok. Step 5 – Now connect from DemoVM2 to DB instance in DemoVM1 Step 6 – Close port 1433 in the Windows firewall netsh advfirewall firewall delete rule name=DemoVM1Port Output: Deleted 1 rule(s). Ok. netsh advfirewall firewall show  rule name=DemoVM1Port No rules match the specified criteria.   Step 7 – Try to connect from DemoVM2 to DB Instance in DemoVM1  Because port 1433 has been closed (in step 6) in the Windows Firewall in VM1 machine, we can longer connect from VM3 remotely to VM1. Scenario 2: VMs provisioned in different Cloud Services 2 Virtual machines configured in different cloud services. Both VMs running different SQL Server instances on them. Both VMs configured with remote PowerShell turned on to be able to run PS and other commands directly into them remotely in order to re-configure them to allow incoming SQL connections from a remote VM or on on-premise machine(s). Note: RDP (Remote Desktop Protocol) is kept configured in both VMs by default to be able to remote connect to them and check the connections to SQL instances for demo purposes only; but not actually needed. Step 1 – Provision new VM3 Provision VM3; named DemoVM3 as follows (see examples screenshots below if using the portal): After provisioning is complete, here is the default port configurations: Step 2 – Add public port to VM1 connect to from VM3’s DB instance Since VM3 and VM1 are not connected in the same cloud service, we will need to specify the full DNS address while connecting between the machines which includes the public port. We shall add a public port 57000 in this case that is linked to private port 1433 which will be used later to connect to the DB instance. Step 3 – Remote Powershell to DemoVM1 Enter-PSSession -ComputerName condemo.cloudapp.net -Port 61503 -Credential <UserName> -UseSSL -SessionOption (New-PSSessionOption -SkipCACheck -SkipCNCheck) You will then be prompted to enter the password.   Step 4 – Open 1433 port in the Windows firewall netsh advfirewall firewall add rule name="DemoVM1Port" dir=in localport=1433 protocol=TCP action=allow Output: Ok. netsh advfirewall firewall show rule name=DemoVM1Port Rule Name:                            DemoVM1Port ---------------------------------------------------------------------- Enabled:                              Yes Direction:                            In Profiles:                             Domain,Private,Public Grouping:                             LocalIP:                              Any RemoteIP:                             Any Protocol:                             TCP LocalPort:                            1433 RemotePort:                           Any Edge traversal:                       No Action:                               Allow Ok.   Step 5 – Now connect from DemoVM3 to DB instance in DemoVM1 RDP into VM3, launch SSM and Connect to VM1’s DB instance as follows. You must specify the full server name using the DNS address and public port number configured above. Step 6 – Close port 1433 in the Windows firewall netsh advfirewall firewall delete rule name=DemoVM1Port   Output: Deleted 1 rule(s). Ok. netsh advfirewall firewall show  rule name=DemoVM1Port No rules match the specified criteria.  Step 7 – Try to connect from DemoVM2 to DB Instance in DemoVM1  Because port 1433 has been closed (in step 6) in the Windows Firewall in VM1 machine, we can no longer connect from VM3 remotely to VM1. Conclusion Through the new support for remote PowerShell in Windows Azure Virtual Machines, one can script and automate many Virtual Machine and SQL management tasks. In this blog, we have demonstrated, how to start a remote PowerShell session, re-configure Virtual Machine firewall to allow (or disallow) SQL Server connections. References SQL Server in Windows Azure Virtual Machines   Originally posted at http://blogs.msdn.com/b/sqlosteam/

  Read the article

• No network connectivity (not wired or wireless) - RT5390

  - by Ben Udy

  I am starting to think I simply need to accept a small loss and sell my new ASUS K73E. Because I really don't enjoy computing when I have to deal with Windough$ and this windows 7 64 bit on my new ASUS is even worse than the old machines with XP. I have written to ASUS and they simply say "We don't support Linux" and while Ralink's website says they do support Linux I can't get anyone to tell me what model Ralink card might be in my machine. Is anyone out there who might be able to give me some useful advice???? Here is the answer to command lspci nn && lsusb && lsmod && rfkill list all: di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 Edit #2 lspci 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c49 (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 02:00.0 Network controller: RaLink Device 5390 03:00.0 Ethernet controller: Atheros Communications Device 1083 (rev c0) lsusb Bus 002 Device 002: ID 8087:0024 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 13d3:5710 IMC Networks Bus 001 Device 002: ID 8087:0024 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Thanks for the suggestion because this gave me a model for Ralink RT5390. I have now gone to Ralink.com and downloaded (via Windows 7) the driver package (it is a bz2 file). I hope I can figure out how to install it. And FYI - I was not able to run su (not authorized?) and dmidecode didn't exist (probably needs to be downloaded BUT no internet yet in Ubuntu)

  Read the article

• Ierrs on Network Interface - Pfsense/Freebsd

  - by JFA

  Hello all, We're using PfSense as an internal router/firewall (no connection to WAN). Using the Web-GUI, under Status --- Interfaces, there's one particular interface where I have some errors: In/out errors 3513/0 I then SSHed to the firewall to validate the info provided by the WebGUI and here's the output: # netstat -ni -I bce2 Name Mtu Network Address Ipkts Ierrs Opkt Oerrs Coll bce2 1500 <Link#3> 00:23:7d:cd:a2:a2 1404522323 3513 749797131 0 0 bce2 1500 10.42.1.0/24 10.42.1.24 6 - 6 - - As you can see, both present the same info (errors on incoming packets). I switched cables, changed network card, changed port on switch and I still see the errors. My 2 questions really are: 1) Is there any way I could get more info on the nature of these errors? or is this all I can get? 2) Should I be worried about this? As you can see, the errors are a VERY LOW percentage of all the total incoming packets. In other words, is this normal on a high-traffic gigabit interface? Thanks! JFA

  Read the article

• System Idle Process network traffic?-Updated

  - by Moab

  I was using NetBalancer and noticed network traffic on an unidentified service, but when I highlight it and then go to the lower center pane and click the parent process it says it is the System Idle process, it is showing incoming and outgoing traffic in the upper pane, anyone know why this Windows System Idle Process is talking on the network? Windows 7 HP 64bit . . . Edit, after blocking the traffic for that unidentified Service I checked my event viewer (Windows LogsSystem) and found 3 new events that were never recorded before and matched the time I blocked the traffic. So is this part of the Windows local DNS cache? Event ID 1014 DNS Client Events Name resolution for the name dns.msftncsi.com timed out after none of the configured DNS servers responded. dns.msftncsi.com Name resolution for the name wpad.home timed out after none of the configured DNS servers responded. wpad Name resolution for the name mscrl.microsoft.com timed out after none of the configured DNS servers responded. mscrl.microsoft.com . Then My Web Browser refused to work, I re-enabled the traffic and all returned to normal. .

  Read the article

• Protocol to mount fat32 network filesystem on Linux with ability to lock files ( not advisory locks

  - by nagul

  I have a fat32 filesystem sitting on a NAS storage device (nslu2) that I need to mount on my Ubuntu system. I've tried Samba and NFS mounts, but both don't seem to support proper locking. More specifically, I am unable to save files to the mounted drive through GNUcash, KeepassX etc, which makes the share fairly useless. Is there a protocol that allows me to achieve this ? Note that the NAS storage device is running a linux OS so I can run pretty much any protocol that has a linux implementation. The only option I'm not looking for is to reformat the partition to ext3, which I'm not able to do due to other constraints. Alternatively, has anyone managed proper locking of a fat32 system over the network using Samba ? Or, is advisory locking the best you get with a network-mounted fat32 file system ? I've thought of trying sshfs but I've not found any indication that this will solve my problem. Edit: Okay, maybe I can reformat the drive, but to any file system except ext3. The "unslung" nslu2 doesn't like more than one ext3 drive, and I already have one attached. So any solution that involves reformatting the drive to ntfs, hfs etc is fine, as long as I can mount it on linux and lock files.

  Read the article

• Problem with network policy rule in Network Policy Server

  - by Robert Moir

  Trying to configure RADIUS for a college network, and have run into the following frustration: I can't set an "AND" condition for group membership of authenticated objects in the network policy rules, e.g. I'm trying to create a NPS rule that says, essentially "IF user is a member of [list of user groups] And is authenticating from a computer in [wireless computer group] then allow access. The screenshot above is the rule I am having trouble with. It does not work as written. The rule underneath it, which is identical in every aspect except the conditions rule, does work. I've tried changing the non-working rule to define each set of groups as "Windows group" rather than specifically as machine and user groups, with no change. With the "faulty" rule enabled and the working one disabled, any attempt to login with a valid account from a machine that is in the wireless computers group gives a 6273 audit event in the windows event log: Reason code 66 - "the user attempted to use an authentication method that is not enabled on the matching network policy". Disabling the "faulty" rule, enabling the other rule and logging in with the same account and computer works just fine.

  Read the article

• Programmer configuring a new network

  - by David Lively

  I'm in the process of expanding my home network from a couple of laptops on a wireless Verizon FiOS router to include: Linksys 24-port switch Cisco Pix 515 Cisco 3640 router One new development desktop and three new machines to act as a db server, web server and a backup system. My company is moving offices and we've decommissioned some older hardware, which I was able to pick up for the cost of the labor to move it home from the office. The benefits to working with dedicated web and db servers are very valuable to me. I know very little about network topology, other than that everything plugs into the switch, which then plugs into the cheap Verizon router. (Verizon provides a coax connection that the router must translate into Ethernet before I can use it with any of this equipment). Questions: What is the recommended topology for this equipment? Verizon router - Pix - 3600 - switch? Is the 3600 even necessary or desirable? The Verizon router has one WAN port and 4 client ports, all 10/100. Is there any performance benefit at all to wiring multiple connections from the verizon router to the switch, assuming I don't use the Pix? Should I use the Pix? Software firewalls are a pain, and seem silly if I have a device like this lying around. Anything else I should know? Am I wasting my time with this? I also obtained a 7 foot rack, shelves, patch panels, UPS, patch panels, etc, which are going into a conveniently air conditioned closet. All constructive advice appreciated.

  Read the article

• Network to network VPN Centos 5

  - by Atul Kulkarni

  I am trying to follow "http://www.centos.org/docs/5/html/Deployment_Guide-en-US/ch-vpn.html#s1-ipsec-net2net" I have come up with the following On local router machine: in my ifcfg-ipsec0: ONBOOT=yes IKE_METHOD=PSK DSTGW=10.5.27.1 SRCGW=10.6.159.1 DSTNET=10.5.27.0/25 SRCNET=10.6.159.0/24 DST=205.X.X.X TYPE=IPSEC I have /etc/sysconfig/network-scripts/keys-ipsec0 file in place. On Remote Machine in the cloud if have /etc/sysconfig/network-scripts/ifcfg-ipsec1: TYPE=IPSEC ONBOOT=yes IKE_METHOD=PSK SRCGW=10.5.27.1 DSTGW=10.6.159.1 SRCNET=10.5.27.124/25 DSTNET=10.6.159.0/24 DST=38.x.x.x with its respective /etc/sysconfig/network-scripts/key-ipsec1 file. The DST in both cases are NAT'd external IPs. Is that a problem? I have made changes for port forwarding as well. When I try to bring the interfaces up it gives me output "RTNETLINK answers: Invalid argument". I am confused now and don't know what more to do? Any place I can digup what parameters were wrong? I really appreciate any help I can get. Thanks and Regards, Atul.

  Read the article

• Can't access certain web sites - reset router, any ideas?

  - by IniTech

  EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• How can I switch from a custom linux network namespace back to the default one?

  - by Martin

  With ip netns exec you can execute a command in a custom network namespace - but is there also a way to execute a command in the default namespace? For example, after executing these two commands: sudo ip netns add test_ns sudo ip netns exec test_ns bash How can the newly created bash execute programs in the default network namespace? There is no ip netns exec default or anything similar as far as I've found. My scenario is: I want to run a SSH server in a separate network namespace (to keep the rest of the system unaware of the network connection, as the system is used for network testing), but want to be able to execute programs in the default network namespace via the SSH connection. What I've found out so far: Created network namespaces are listed as files under /var/run/netns (but there is no file for the default namespace) The ip netns exec code can be found here: http://git.kernel.org/cgit/linux/kernel/git/shemminger/iproute2.git/tree/ip/ipnetns.c#n132 - I haven't grasped everything that it is doing yet, but it doesn't look very promising. ip netns identify $$ as suggested by Howto query and change network namespace on linux? returns nothing when in the default network namespace

  Read the article

• How to rename network printer on Windows 7?

  - by Adrian McCarthy

  This question is similar to How do you rename a printer device in Windows 7 64 bit, except the answers there do not work, and I'll provide more information. This is a home network, not a domain. I have set up a Brother HL-5170DN. It is a network printer connected directly to an Ethernet hub. I can connect to it with Windows 7, but on Windows 7 it defaults to the name "binary_p1 on Brn37415f", which isn't very useful. And I cannot seem to change the name. I have it working with several Windows XP and Vista machines, and I can change the name on those machines. On Windows 7 Printer properties: I can see the "binary_p1" name on the General tab. I can select the text, but I cannot change it. The field is not grayed out, but I cannot type anything into it. On the Ports tab, all of the controls are grayed out (disabled). The selected Port is called "\\Brn_37415f\binary_p1", and it's described as "Client Side Rendering Provider" and the printer field says "binary_p1". On the Security tab, I can see that my account has "Manage this printer" permissions. If I choose Printer Server Properties, I can select the port and click Configure Port, but I get a dialog that says, "An error occurred during port configuration. This option is not supported." I have found many forums with people asking the same question without getting an answer. Update: No more bounties to offer, but I'm still looking for a solution to this problem.

  Read the article

• Network topology for both direct and routed traffic between two nodes

  - by IndigoFire

  Despite it's small size, this is the most difficult network design problem I've faced. There are three nodes in this network: PC running Windows XP with an internal WiFi adapter.Base station with both WiFi and a Wireless Modem (WiModem)Mobile device with both WiFi and WiModem The modem is a low-bandwidth but high-reliability connection. We'd like to use WiFi for high-bandwidth stuff like file transfers when the mobile is nearby, and the modem for control information. Here's the tricky part: we'd like the wifi traffic to go directly from the mobile to the PC, as rebroadcasting packets on the same WiFi channel takes up double the bandwidth. We can do that with a manual configuration by giving the both the PC and the base station two IP addresses for their WiFi interfaces: one on a subnet shared with the mobile, and one on their own subnet. The routes on the PC are set up so that any traffic going to the mobile via WiModem goes through the secondary IP address so that return traffic from the mobile also goes through the WiModem. Here's what that looks like: PC WiFi 1: 192.168.2.10/24 WiFi 2: 192.168.3.10/24 Default route: 192.168.2.1 Base Station WiFi 1: 192.168.2.1/24 WiFi 2: 192.168.3.1/24 WiModem: 192.168.4.1/24 Mobile WiFi: 192.168.3.20/24 WiModem: 192.168.4.20/24 We'd like to move to having the base station automatically configure the mobile and PC, as the manual setup is problematic when you start having multiple mobiles and PCs. This means that the PC can only have 1 IP address and needs to be treated as being pretty simple. Is it possible to have a setup driven by DHCP on the base station that is efficient with bandwidth?

  Read the article

• Local Network - Windows 7 and Vista can't see each other

  - by ca8msm

  I've got a strange issue at home that has been bugging me for weeks, but I really need to get it sorted now so I'll detail as much as I can and hopefully someone can spot what might might be wrong. I have a wireless router connected to the internet and 3 devices connected to it. They are: Name OS Network IPv4 PC1 Windows 7 WORKGROUP 192.168.2.2 LAPTOP1 Vista WORKGROUP 192.168.2.3 PS3 192.168.2.4 and they all get their IP addresses dynamically. Both PC1 and LAPTOP1 can ping PS3 and get a response. PC1 and LAPTOP1 are unable to ping each other by ip address unless I ping by their name (which bizarrely shows that it is pinging via the IPv6 address). Also, to confirm this both PC1 and LAPTOP1 can ping each other via the long IPv6 address that they both have so they can obviously see each other just not via IPv4. I've disabled the firewalls on both machines as well to rule that out. I don't really know what IPv6 is used for and I've tried disabling it on both machines but all that happens then is that neither machine can see each other at all then. Does anyone have any idea of what may be stopping them seeing each other, any ways I can look at fixing this, or any network tools that may help identify where it is failing? Thanks, Mark

  Read the article

• Network programming and Packets interactions.

  - by Eyla

  Greeting, This month I will start working on my master thesis. My thesis's subject is about network security. I need to deal with network interfaces and packets. I've used shappcap before to interact with packets but I'm not sure if C# is the most powerful language to deal with network programing and packets. I worked a bit with winshark and I saw how powerful it is and as you know winsharp is open source developed using C++. I'm not sure if I should use C# or C++ for network security programming and I want your through about the best language might be for network programming and packets interaction. should I use C#, C++, or java or some thing else? please give me your advice. Thank you,

  Read the article

• Android - modes of connectivity, device identification and device inter-communication?

  - by MalcomTucker

  Can someone explain a couple of very simple concepts to me - I'm interested in mobile devices running android and how they are identified over networks. Some scenarios: Device is connected over WiFi - presumably the device has a standard IP address as with any host and can communicate with any other android host over TCP/IP (assuming it knows the participating device's IP? Device is connected over bluetooth - how are devices identified in this case? Device is connected over mobile operator's network - this is the one I'm interested in and confused by - is there anyway for two or more devices to discover each other and communicate via the mobile operator's network? How does a device communicate with a backend server in this scenario? In other words, how do apps and devices communicate when not connected to a WiFi network? Thanks for any advice..

  Read the article

• Cloud to On-Premise Connectivity Patterns

  - by Rajesh Raheja

  Do you have a requirement to convert an Opportunity in Salesforce.com to an Order/Quote in Oracle E-Business Suite? Or maybe you want the creation of an Oracle RightNow Incident to trigger an on-premise Oracle E-Business Suite Service Request creation for RMA and Field Scheduling? If so, read on. In a previous blog post, I discussed integrating TO cloud applications, however the use cases above are the reverse i.e. receiving data FROM cloud applications (SaaS) TO on-premise applications/databases that sit behind a firewall. Oracle SOA Suite is assumed to be on-premise with with Oracle Service Bus as the mediation and virtualization layer. The main considerations for the patterns are are security i.e. shielding enterprise resources; and scalability i.e. minimizing firewall latency. Let me use an analogy to help visualize the patterns: the on-premise system is your home - with your most valuable possessions - and the SaaS app is your favorite on-line store which regularly ships (inbound calls) various types of parcels/items (message types/service operations). You need the items at home (on-premise) but want to safe guard against misguided elements of society (internet threats) who may masquerade as postal workers and vandalize property (denial of service?). Let's look at the patterns. Pattern: Pull from Cloud The on-premise system polls from the SaaS apps and picks up the message instead of having it delivered. This may be done using Oracle RightNow Object Query Language or SOAP APIs. This is particularly suited for certain integration approaches wherein messages are trickling in, can be centralized and batched e.g. retrieving event notifications on an hourly schedule from the Oracle Messaging Service. To compare this pattern with the home analogy, you are avoiding any deliveries to your home and instead go to the post office/UPS/Fedex store to pick up your parcel. Every time. Pros: On-premise assets not exposed to the Internet, firewall issues avoided by only initiating outbound connections Cons: Polling mechanisms may affect performance, may not satisfy near real-time requirements Pattern: Open Firewall Ports The on-premise system exposes the web services that needs to be invoked by the cloud application. This requires opening up firewall ports, routing calls to the appropriate internal services behind the firewall. Fusion Applications uses this pattern, and auto-provisions the services on the various virtual hosts to secure the topology. This works well for service integration, but may not suffice for large volume data integration. Using the home analogy, you have now decided to receive parcels instead of going to the post office every time. A door mail slot cut out allows the postman can drop small parcels, but there is still concern about cutting new holes for larger packages. Pros: optimal pattern for near real-time needs, simpler administration once the service is provisioned Cons: Needs firewall ports to be opened up for new services, may not suffice for batch integration requiring direct database access Pattern: Virtual Private Networking The on-premise network is "extended" to the cloud (or an intermediary on-demand / managed service offering) using Virtual Private Networking (VPN) so that messages are delivered to the on-premise system in a trusted channel. Using the home analogy, you entrust a set of keys with a neighbor or property manager who receives the packages, and then drops it inside your home. Pros: Individual firewall ports don't need to be opened, more suited for high scalability needs, can support large volume data integration, easier management of one connection vs a multitude of open ports Cons: VPN setup, specific hardware support, requires cloud provider to support virtual private computing Pattern: Reverse Proxy / API Gateway The on-premise system uses a reverse proxy "API gateway" software on the DMZ to receive messages. The reverse proxy can be implemented using various mechanisms e.g. Oracle API Gateway provides firewall and proxy services along with comprehensive security, auditing, throttling benefits. If a firewall already exists, then Oracle Service Bus or Oracle HTTP Server virtual hosts can provide reverse proxy implementations on the DMZ. Custom built implementations are also possible if specific functionality (such as message store-n-forward) is needed. In the home analogy, this pattern sits in between cutting mail slots and handing over keys. Instead, you install (and maintain) a mailbox in your home premises outside your door. The post office delivers the parcels in your mailbox, from where you can securely retrieve it. Pros: Very secure, very flexible Cons: Introduces a new software component, needs DMZ deployment and management Pattern: On-Premise Agent (Tunneling) A light weight "agent" software sits behind the firewall and initiates the communication with the cloud, thereby avoiding firewall issues. It then maintains a bi-directional connection either with pull or push based approaches using (or abusing, depending on your viewpoint) the HTTP protocol. Programming protocols such as Comet, WebSockets, HTTP CONNECT, HTTP SSH Tunneling etc. are possible implementation options. In the home analogy, a resident receives the parcel from the postal worker by opening the door, however you still take precautions with chain locks and package inspections. Pros: Light weight software, IT doesn't need to setup anything Cons: May bypass critical firewall checks e.g. virus scans, separate software download, proliferation of non-IT managed software Conclusion The patterns above are some of the most commonly encountered ones for cloud to on-premise integration. Selecting the right pattern for your project involves looking at your scalability needs, security restrictions, sync vs asynchronous implementation, near real-time vs batch expectations, cloud provider capabilities, budget, and more. In some cases, the basic "Pull from Cloud" may be acceptable, whereas in others, an extensive VPN topology may be well justified. For more details on the Oracle cloud integration strategy, download this white paper.

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >