Search Results

Search found 18773 results on 751 pages for 'router configuration'.

Page 17/751 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Fastest router for OpenWRT/etc?

  - by marienbad

  I realize OpenWRT Wiki hardware info tells CPU model and MHz for many routers, but MHz doesn't directly map to speed. So... as far as you know, what are some of the fastest OpenWRT-compatible wifi routers out there?

  Read the article

• Juniper Networks SRX240 as a office router?

  - by Jordan Mendelson

  We're a small (7 person) fast growing startup who just got our new office and we're having a 100 Mbps line installed from Cogent. I'm not familiar with Juniper devices, however the equivalent Cisco appears to be rather expensive. Features we'd like: Offsite VPN access (PPTP or L2TP IPsec) - something Mac compatible IPv6 support NAT - ideally supporting multiple outside addresses mapped to VLANs DHCP DNS forwarding would be nice QoS to keep our SIP phones happy (managed through RingCentral) VLANs for guest/internal The device is going to be connected to a set of SIP phones as well as two Ruckus 7962s for wireless access. Eventually I'd like to connect it to a Juniper ESX switch as we grow. Would a Juniper SRX240 handle this ok?

  Read the article

• Block P2P traffic on a Linksys router WRT54G with tomato firmware

  - by Kami

  Hi, I'm running a small wireless network (6 to 10 users) on a Lynksys WRT54G with tomato firmware sharing an internet connection. I don't want the users to download files with bittorrent (mainly used) and other p2p apps. I've also found some solutions about lowering p2p traffic priority using QoS. I really need to BAN p2p traffic. Does anyone know how to setup some rules to deny that kind of traffic ? I've tried to setup an Access Restriction Rule: But it's not working at all ...

  Read the article

• Sharing an Apache configuration between testing vs. production

  - by Kevin Reid

  I have a personal web site with a slightly nontrivial Apache configuration. I test changes on my personal machine before uploading them to the server. The path to the files on disk and the root URL of the site are of course different between the test and production conditions, and they occur many places in the configuration (especially <Directory blocks for special locations which have scripts or no directory listing or ...). What is the best way to share the common elements of the configuration, to make sure that my production environment matches my test environment as closely as possible? What I've thought of is to use SetEnv to store the paths for the current machine in environment variables, then Include a common configuration file with ${} everywhere there's something machine specific. Any hazards of this method?

  Read the article

• Reboot Zyxel router via Telnet

  - by Kieron

  Hi, I've got a Zyxel P-661HW-D1, I was wondering if anyone knows how to reboot it via telnet? I can't seem to find the command... Thanks, Kieron

  Read the article

• Westell router setup page

  - by eych

  I can connect to the internet, ping 192.168.1.1 with no problem, haven't changed any firewall or Anti-virus settings, but bringing up 192.168.1.1 in the browser gives 'Problem loading page'. XP machine...was able to connect to the setup page few weeks ago. Any thoughts?

  Read the article

• Where can I find WebSphere configuration files?

  - by Nicholas Key

  Hi there, I would like to know where are the WebSphere configuration details saved? Specifically, configuration details that are shown in the Administrative Console (from the web) or from the console using wsadmin. Some of the examples would be: Java and Process Management: Class loader, Process definition, Process execution Container Settings: Session management, SIP Container Settings, Web Container Settings, Portlet Container Settings Are there XML files that persist these configuration details? Nicholas

  Read the article

• Checking the configuration of two systems to determine changes

  - by None

  We are standing up a replicant data center at work and need to ensure that the new data center is configured (nearly) identically to the original. The new data center will be differently addressed and named than the original and will have differing user accounts, but all the COTS, patches, and configurations should be the same. We would normally ghost the original servers and install those images onto the new machines, however, we have a few problematic pieces of COTS that require we install them outside of an image due to how they capture the setup of the network during their installation and maintain it within their configuration information (in some cases storing it in various databases). We have tried multiple times and this piece of COTS cannot be captured within a ghost image unless the destination machine will have an identical network setup (all the same IPs, hostnames, user accounts, etc across the entire network) as the original. In truth, it is the setup of these special COTS that I want to audit the most because they are difficult to install and configure in the first place. In light of the fact that we can’t simply ghost, I’m trying to find a reasonable manner to audit the new data center and check to see if it is setup like the original (some sort of system wide configuration audit or integrity check). I’m considering using something like Tripwire for Servers to capture the configuration on the source machines and then run an audit on the destination machines. I understand that it will still show some differences due to the minor config changes, but I’m hoping that it will eliminate the majority of the work. Here are some of the constraints I’m working under: Data center is comprised of multiple Windows and Linux machines of differing versions (about 20 total) I absolutely cannot ghost or snap any other type of image of these machines … at least not in their final configuration I want to audit the final configuration to ensure all of the COTS, patches, configurations, etc are installed and setup properly (as compared to the original data center) I would rather not install any additional tools on these machines … I’d much rather run it from a standalone machine or off a DVD Price of tools is important but not an impossible burden, however, getting a solution soon is important (I can’t take the time to roll my own tools to do this) For the COTS that stores the network information, I don’t know all of the places it stores the network information … so it would be unlikely I could find a way in the near future to adjust its setup after the installation has occurred Anyone have any thoughts or alternate approaches? Can anyone recommend tools that would be usable for system wide configuration audits?

  Read the article

• Block P2P traffic on a Linksys router WRT54G with Tomato firmware

  - by Kami

  I'm running a small wireless network (6 to 10 users) on a Linksys WRT54G with Tomato firmware sharing an Internet connection. I don't want the users to download files with BitTorrent (mainly used) and other P2P apps. I've also found some solutions about lowering P2P traffic priority using QoS. I really need to ban P2P traffic. Does anyone know how to setup some rules to deny that kind of traffic? I've tried to setup an Access Restriction Rule: However it's not working at all.

  Read the article

• A home router for torrents, gaming, webbing and detailed QoS [closed]

  - by Cawas

  I want to plug in an external HD on it to torrent up never ending (mostly for seeding), with lowest priority. It should even automatically completely stop if it disturbs my net usage, and go back in later. And I want to be able to give gaming (or my computer) the highest priority, because of its ping requirements. It should be above even of Skype and any voip, which also have high priority. Web surfing and "youtubing" comes in the middle - it won't matter much if it delays a second or two. Finally, interface as simple as possible. It's fine if it's command line setup, but it needs to have a GUI. What are my options for routers / firmwares as described? Maybe Gargoyle? Or even Time Capsule? It seems to me good old DD-WRT isn't the best option out there anymore. I wonder what else could cover these grounds.

  Read the article

• Access 2 sites on same machine behind a router

  - by Luc

  Hello, I have several machines on my lan. On of them is running 2 web sites, first_web_site and second_web_site (each one in a dedicated NameVirtualHost). Another machine is running another site third_web_site. I would like to be able to access each one, within internet, with the url: first_web_site.domain.tld second_web_site.domain.tld third_web_site.domain.tld knowing that 2 sites are on the same machine. Can Apache help me to do this ? I have a machine that will have a apache server to be used for proxy purposes. I was talk to set up virtualhost on this one and use proxy server but I do not know how to do this. Could you please give me hints ? Thanks a lot, Luc

  Read the article

• OSS Router firmwares

  - by Cherian

  DD-WRT, Open WRT , Tomato or Third-party firmware projects ? What are the compelling reasons to choose between these? I used to be a great DD-WRT fan until I realized that the author was deceiving users by publishing it as a OSS, but made it very cumbersome to download the source and change it (requires you to download GB’s of source files) .Also their bandwidth monitoring feature was part of the paid version, which IMHO is a killer. Having said that, DD-WRT just worked. And I think that’s great..

  Read the article

• Toshiba laptop won't connect to D-link router

  - by user3314725

  This is Team 4786 Nicolet Fear FIRST FRC robotics, our problem is we cant get our D-Link (DAP-1522) to connect to our Toshiba (TECRA R950) laptop wireless. It has connected before in the past and we don't know why it is not working anymore. The D-links still function correctly and we think our problem lies within the Toshiba. EDIT:The Toshiba connects to the school Wifi, and other things (small FRC drive station) connect to the D-link, but they won't connect to each other.

  Read the article

• Thomson router reboots unexpectedly with an apparent remote connection attempt

  - by ChrisF

  I've got a weird problem. Every so often my rooter (a Thomson TG585 v8 running version 8.2.7.8 of it's firmware) reboots itself. It seems to be associated with this message in the event log: FIREWALL replay check (1 of 2): Protocol: ICMP Src ip: 183.178.144.177 Dst ip: xxx.xxx.xxx.xxx Type: Destination Unreachable Code: Host Unreacheable xxx.xxx.xxx.xxx is my external IP address 183.178.144.177 resolves to 183178144177.ctinets.com We've got a student from Hong Kong staying with us at the moment and the reboots seem coincidental with him starting up his laptop. I say this because a check on ctinets.com shows it to be based in Hong Kong, though our guest's laptop doesn't appear to have any software related to this company installed. I say "apparently" as he is running the Chinese version of Windows and his English doesn't cover technical subjects like this. I know this is an incoming message but I was assuming that it was in response to something on the student's laptop which is why the first thought was malware, but we've got anti virus on all the other machines and have run malwarebytes on his with a negative result so I don't think the problem is due to a virus or (known) trojan. What else can I do to stop this and identify the cause?

  Read the article

• Decreasing lagging on router, while gaming

  - by user2699451

  I had absolutely no idea where to post this question and get a professional answer for it but here goes... Okay, so I guess everyone whos is reading this had played online, and so I was playing LoL again tonight and my brother decided that now was a great time to go on youtube and start watching a movie, so my ping (connecting from South Africa to EU west server) is around 190-220 average, however it started spiking to 2000 and average was 600-800, so it arised the question, how ther hell can I "kick" him off for the time being I tried reasoning it out with him but its like playing chess with a pigeon, he's studying to be an engineer, and I just cant win an argument with him, so i need to step it up a level... I have in the past used the aireplay method by sending deauth packets but it only helped so much, is there another way of either kicking a peer of the local wifi or decreasing the lag spikes while in session or even splitting the bandwidth equally in 2 or 3,etc What do I do p.s. sorry if off topic, if it is not appropriate, just say which website will be able to help or assist me...

  Read the article

• Arch linux as a wireless router with a USB modem

  - by orlox

  I'm trying to act as an access point to share the internet I get from a USB modem on arch linux. From what I've seen so far, most of what I've found deals with installing particular distributions like DD-WRT to this purpose, but I haven't been able to find any particular and comprehensive solution. Has anyone done this before? I don't know how relevant it might be, but my wireless card is a broadcom device.

  Read the article

• Setting the Server Port in D-Link Router for eMailing Logs

  - by Synetech

  Does anyone know how to set the port for the email server in the Status->Log section of the D-Link DI-524? I’ve tried the setting below but it does not seem to work. I don’t want to use the default port 25 if I can avoid it. (No, the server and email address in the snap are irrelevant, you can replace the server with hotmail.com or whatever and address with a valid one; the question I am trying to figure out is how to set the port.)

  Read the article

• Local Only 3G Router via Broadband Device?

  - by GateKiller

  I am looking for the name/type of device which does the following: Connects to the internet via ethernet or wireless and then produces a "fake" 3G signal for my iPhone to connect to. The 3G siginal in my office is very weak or non-existant and I need a way of boosting or replacing it.

  Read the article

• Apache configuration file visualization/testing

  - by Matt Holgate

  Is there a tool available (or a debug mode built into Apache) that will allow me to interactively test and explain an Apache configuration for a given request? In particular, I'd like to be able to see which directives will apply when requesting a specific URL. For example, the output for the URL http://myserver.com/foo/bar/bar.html might look something like: Allow from 192.168.0.3 <-- From <Location /foo/bar> in myserver.com vhost Require valid user <-- From <Directory /var/www/foo> in global configuration Satisfy any <-- From <File bar.html> in global configuration [Background: why do I want this? The apache merging rules for configuration directives are quite complex to get right. It would be great to have a tool which allows you to check that your rules are doing exactly what you want, and would be a good learning tool]. If there isn't such a tool, is there a debug option in Apache that will log such information for each incoming request?

  Read the article

• Firewall/Router upgrade

  - by Atlas

  We've been using a SonicWall TZ170 for several years, it's been working fine with occasional glitches. Now we switched to a 100Mpbs broadband, and the firewall has become the bottleneck for internet access because its max throughput is around 20-30Mpbs. Any ideas for a replacement? Brand/Model?

  Read the article

• Port forwarding with router in bridged mode

  - by jipje44

  let say R1 and R2. R1 is in bridged mode and connected to R2. R2 is a dhcp server. To R2 is an internet camera connected. When i am on R2 and i do enter the ip of the camera then it will work without a problem. However i want to acces the camera from the outside. So in R2 i forwarded a port (done this one other networks without problems). However I can't connect from the outside. Can R1 blocking the port? I cant log in on R1 as long as it is in bridged mode.

  Read the article

• Install Oracle Configuration Manager's Standalone Collector

  - by Get Proactive Customer Adoption Team

  Untitled Document The Why and the How If you have heard of Oracle Configuration Manager (OCM), but haven’t installed it, I’m guessing this is for one of two reasons. Either you don’t know how it helps you or you don’t know how to install it. I’ll address both of those reasons today. First, let’s take a quick look at how My Oracle Support and the Oracle Configuration Manager work together to gain a good understanding of what their differences and roles are before we tackle the install.   Oracle Configuration Manger is the tool that actually performs the data collection task. You deploy this lightweight piece of software into your system to collect configuration information about the system and OCM uploads that data to Oracle’s customer configuration repository. Oracle Support Engineers then have the configuration data available when you file a service request. You can also view the data through My Oracle Support. The real value is that the data Oracle Configuration Manager collects can help you avoid problems and get your Service Requests solved more quickly. When you view the information in My Oracle Support’s user interface to OCM, it may help you avoid situations that create problems. The proactive tools included in Oracle Configuration Manager help you avoid issues before they occur. You also save time because you didn’t need to open a service request. For example, you can use this capability when you need to compare your system configuration at two points in time, or monitor the system health. If you make the configuration data available to Oracle Support Engineers, when you need to open a Service Request the data helps them diagnose and resolve your critical system issues more quickly, which means you get answers more quickly too. Quick Installation Process Overview Before we dive into the step-by-step details, let me provide a quick overview. For some of you, this will be all you need. Log in to My Oracle Support and download the data collector from Collector tab. If you don’t see the Collector tab, click the More tab gain access. On the Collector tab, you will find a drop-down list showing which platforms are available. You can also see more ways to the Collector can help you if you click through the carousel of benefits. After you download the software for your platform, use FTP to move that file (.zip) from your PC to the server that hosts the Oracle software. Once you have that file on the server, locate the $ORACLE_HOME directory, and unzip the file within that directory. You can then use the command line tool to start the installation process. The installation process requires the My Oracle Support credential (Support Identifier, username, and password) Proxy specification (Host IP Address, Port number, username and password) Installation Step-by-Step Download the collector zip file from My Oracle Support and place it into your $Oracle_Home Unzip the zip file you downloaded from My Oracle Support – this will create a directory named CCR with several subdirectories Using the command line go to “$ORACLE_HOME/CCR/bin” and run the following command “setupCCR” Provide your My Oracle Support credential: login, password, and Support Identifier The installer will start deploying the collector application You have installed the Collector Post Installation Now that you have installed successfully, the scheduler is ready to collect configuration information for the software available in your Oracle Home. By default, the first collection will take place the day after the installation. If you want to run an instrumentation script to start the configuration collection of your Oracle Database server, E-Business Suite, or Enterprise Manager, you will find more details on that in the Installation and Administration Guide for My Oracle Support Configuration Manager. Related documents available on My Oracle Support Oracle Configuration Manager Installation and Administration Guide [ID 728989.5] Oracle Configuration Manager Prerequisites [ID 728473.5] Oracle Configuration Manager Network Connectivity Test [ID 728970.5] Oracle Configuration Manager Collection Overview [ID 728985.5] Oracle Configuration Manager Security Overview [ID 728982.5] Oracle Software Configuration Manager: Disconnected Mode Collection [ID 453412.1]

  Read the article

• Handling Configuration Changes in Windows Azure Applications

  - by Your DisplayName here!

  While finalizing StarterSTS 1.5, I had a closer look at lifetime and configuration management in Windows Azure. (this is no new information – just some bits and pieces compiled at one single place – plus a bit of reality check) When dealing with lifetime management (and especially configuration changes), there are two mechanisms in Windows Azure – a RoleEntryPoint derived class and a couple of events on the RoleEnvironment class. You can find good documentation about RoleEntryPoint here. The RoleEnvironment class features two events that deal with configuration changes – Changing and Changed. Whenever a configuration change gets pushed out by the fabric controller (either changes in the settings section or the instance count of a role) the Changing event gets fired. The event handler receives an instance of the RoleEnvironmentChangingEventArgs type. This contains a collection of type RoleEnvironmentChange. This in turn is a base class for two other classes that detail the two types of possible configuration changes I mentioned above: RoleEnvironmentConfigurationSettingsChange (configuration settings) and RoleEnvironmentTopologyChange (instance count). The two respective classes contain information about which configuration setting and which role has been changed. Furthermore the Changing event can trigger a role recycle (aka reboot) by setting EventArgs.Cancel to true. So your typical job in the Changing event handler is to figure if your application can handle these configuration changes at runtime, or if you rather want a clean restart. Prior to the SDK 1.3 VS Templates – the following code was generated to reboot if any configuration settings have changed: private void RoleEnvironmentChanging(object sender, RoleEnvironmentChangingEventArgs e) {     // If a configuration setting is changing     if (e.Changes.Any(change => change is RoleEnvironmentConfigurationSettingChange))     {         // Set e.Cancel to true to restart this role instance         e.Cancel = true;     } } This is a little drastic as a default since most applications will work just fine with changed configuration – maybe that’s the reason this code has gone away in the 1.3 SDK templates (more). The Changed event gets fired after the configuration changes have been applied. Again the changes will get passed in just like in the Changing event. But from this point on RoleEnvironment.GetConfigurationSettingValue() will return the new values. You can still decide to recycle if some change was so drastic that you need a restart. You can use RoleEnvironment.RequestRecycle() for that (more). As a rule of thumb: When you always use GetConfigurationSettingValue to read from configuration (and there is no bigger state involved) – you typically don’t need to recycle. In the case of StarterSTS, I had to abstract away the physical configuration system and read the actual configuration (either from web.config or the Azure service configuration) at startup. I then cache the configuration settings in memory. This means I indeed need to take action when configuration changes – so in my case I simply clear the cache, and the new config values get read on the next access to my internal configuration object. No downtime – nice! Gotcha A very natural place to hook up the RoleEnvironment lifetime events is the RoleEntryPoint derived class. But with the move to the full IIS model in 1.3 – the RoleEntryPoint methods get executed in a different AppDomain (even in a different process) – see here.. You might no be able to call into your application code to e.g. clear a cache. Keep that in mind! In this case you need to handle these events from e.g. global.asax.

  Read the article

• Create kickstart configuration file from existing configuration.

  - by ÜMineiro

  Is there a script or another way to automatically generate a kickstart configuration file from the system state of an existing server so that the file can be use to replicate (not clone) the configuration of the system in another install? I know that the anaconda-ks.cfg file is stored on the /root dir. but the system in question have been extensively changed since it's installation, and the file is of no use now.

  Read the article

• Internet in the router but not in the local network.

  - by TheMouse

  I have a PC and a laptop (Windows 7 - both) which should connect through router to Internet. The router is Linksys wrt120. My ISP is using PPPoE. I have connected the Internet cable to the router, clone the MAC of my PC, writing the username and the password for my Internet connection. After seconds the router has acquired IP from my ISP. I have used the administration panel of Linksys and with the help of the ping and tracert commands which are built into it - I can connect to the world, outside the network. The problem is when I try to connect the PC or the laptop to the network. There's no problem here. The DHCP server of the router gives them appropriate addresses. The problem is that they couldn't connect to either Internet addresses (google.com) or IP addresses. But they can connect to the router and its control panel. I tried several times, reset the router..but there's no Internet..still.

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >