Search Results

Search found 462 results on 19 pages for 'spin docta'.

Page 17/19 | < Previous Page | 13 14 15 16 17 18 19  | Next Page >

  • Can this USB3 behaviour be anything else than a hardware failure?

    - by Jonas Wielicki
    While my motherboard is half a year old now (ASUS M5A99X EVO), I only recently made use of the USB3 boards (after purchase of USB3 external harddrive). However, I am encountering issues. I am running linux 3.6.7-4.fc16.x86_64. Initially, the harddrive worked fine with USB3 (amazing ˜160MB/s), but I had some problems after putting after putting the harddrive to sleep manually after use (backup) with hdparm -Y. After some time, the device disappears from lsusb and i see the following in dmesg: [ 1924.091107] xhci_hcd 0000:05:00.0: xHCI host not responding to stop endpoint command. [ 1924.091114] xhci_hcd 0000:05:00.0: Assuming host is dying, halting host. [ 1924.091147] xhci_hcd 0000:05:00.0: HC died; cleaning up [ 1924.091233] usb 11-1: USB disconnect, device number 2 [ 1924.091272] sd 6:0:0:0: Device offlined - not ready after error recovery Testing with my (USB3 capable) notebook, I could not immediately reproduce the behaivour. I put the drive to sleep with hdparm -Y and waited for like an hour, but it was still listed in lsusb and responded after a few seconds delay when I tried after the hour of waiting. After an hour, on the desktop, the device would've usually vanished. Googling for this issue, I came across hints that playing around with IOMMU settings and upgrading the BIOS might help. I upgraded the BIOS and tried both with and without IOMMU enabled, got similar results. Most disturbing is, that one of the two USB 3.0 hubs sometimes also disappears from lsusb (or does not show up after boot at all). I've also heard that there are some hardware issues with ASUS USB3 ports. Applying mechanic force to the capble doesn't push the issue to one side or the other. Also, udev seems to reenumerate all devices if I plug the HDD into the USB 3.0 port without success (I can notice from my keyboard layout being changed to the default, which I do not use normally). The drive is externally powered and the external power supply is plugged in (it also stays powered when unplugging from USB, although it will spin down then). So before I try to return the board, I wanted to find out whether this can be anything else than a failure on the motherboard?

    Read the article

  • Recover strategy single bad sector in moricon

    - by Damon
    This week, my harddisk made me an early christmas present in the form of a single defect sector. To make up for the puny size of the present, it chose a sector inside moricons.dll for that. This means that now the system takes about 5 minutes to boot before Windows gives up and moves on, and there's 2 dozen scary "critical failure" entries in the system log after every boot, which is annoying. OK, admittedly, I shouldn't complain, it could be worse, the bad sector could be in ntldr... SMART info more or less indicates (for what SMART can indicate anyway) that the drive is mostly OK. Soft Read Error Rate has a score of 96, and Current Pending Sector Count has a raw value of 8, which translates to a score of 100. Acronis DriveMonitor makes this an issue (lowering the overall rating to 75%), HDD Health calls it "excellent", giving an overall rating of 95% (which is what this harddisk from day one). No single score is below 95 (power on hours and spin up count), and most are 100 anyway. Well, whatever, I've seen drives with perfect SMART values fail from one second to the other, and drives with moderate values work for years. So, I'm inclined not to put too much weight into that overall. TL;DR Now... to the problem: I don't feel like trashing the disk just yet (that's planned with a new OS install upgrading to Win7 early next year, independently of this issue), but in the mean time, I would still like to have a smoothly running system again. Therefore, I feel tempted to tamper with it, but before I render my system entirely unusable (since I've never done this before), I'd like to verify that my planned procedere is likely to suceed in having a working system again: Copy moricons.dl_ from the Windows install disk, rename it to moricons.zip, and unzip it. This gives an intact 5.1.2600.2180 version (the broken one is 5.1.2600.5512 - but I guess this makes not much of a difference, since it's an icon-only DLL, and an outdated copy should work better than one that can't be read) Run chkdsk /r /f` which will "repair" the file (i.e. delete the file without asking, tell the drive to remap the sector, and toss some unreadable junk into a file with a hexadecimal number) Hopefully Windows still boots after this (is that a reasonable expectation, or do I need to have something like BartPE ready? -- but then again, what's that good for in case chkdsk has nuked the entire file system...) Delete the junk file generated by chkdsk, copy the new DLL to %windir%\system32 Reboot. Pray. Maybe I just shouldn't touch anything, since it still kind of works... if annoying, but it works. Unsure... But, is there anything fundamentally wrong with the planned approach? Is this a sensible approach at all?

    Read the article

  • System won't boot: Gigabyte HD 7790 1GB OC GPU issue or Corsair VS550 PSU issue?

    - by MGOwen
    Installed a new GPU, and PC won't boot. Turn it on and: No monitor signal at all (tried HDMI and VGA via DVI, on 2 working monitors). CPU and GPU fans DO spin, but No system beeps, no sounds from drives (they might make a small noise in the first 1 second or so, but there's definitely no OS loading or anything like that) If hit "power off" button it turns off immediately (no holding down for 3 seconds like usual) If I put my old HD 5670 GPU back in, everything works fine. But (plot twist!) card is not totally dead. My friend put it in his PC, and it works fine (he even played a game for 15 minutes, no issues). He has a Corsair TX850 850W and a Gigabyte MB. So my main theory is: the GPU isn't getting enough power from the PSU. But is it: Bad PSU? Seems unlikely, since it works fine with the other GPU. Also, the PSU Is brand new and 550W (single 42A/504W 12V rail). Overkill for this GPU. Corsair is a decent brand, but maybe just mine is faulty? Bad GPU? Could it be drawing more power than it should be, somehow, or something? Supposedly HD 7790 needs only 21A/75W on the 12v rail, though this one is factory overclocked a bit... but should that triple the power requirement? Something else? Could there be a motherboard incompatibility somehow? Both MB and GPU are less than a year old and PCI Express 3.0 x16. Things I've tried: Re-seating the video card Testing PC with old GPU (works fine, same PCIe slot). Checked AMD's stated amp/watt requirements of a 7790 and my PSU (see above). My PSU can output twice the amps (single rail) and 5x the Wattage a 7790 needs. Here are the full specs: Gigabyte HD 7790 1GB OC GPU Corsair VS550 550W PSU 4GB RAM AsRock H61M U3S3 motherboard i3-2100 500GB SATA HDD (2007-ish) blu-ray drive (new) PCI 802.11g card Edit: Motherboard BIOS Update seems to have fixed it. (If anyone has same problem and it doesn't work, comment here).

    Read the article

  • What is wrong with my gtkrc file?

    - by PP
    I have written following gtkrc file from some other theme gtkrc file. This theme is normal theme with buttons using pixmap theme engine. I have also given background image to GtkEntry. Problem is that, When i use this theme my buttons doesn't show text one them and my entry box does not show cursor. Plus in engine "pixmap" tag I need to specify image name with it's path as I have already mentioned pixmap_path on the top of rc file but why I still need to specify the path in file = "xxx" # gtkrc file. pixmap_path "./backgrounds:./icons:./buttons:./emotions" gtk-button-images = 1 #Icon Sizes and color definitions gtk-icon-sizes = "gtk-small-toolbar=16,16:gtk-large-toolbar=24,24:gtk-button=16,16" gtk-toolbar-icon-size = GTK_ICON_SIZE_SMALL_TOOLBAR gtk_color_scheme = "fg_color:#000000\nbg_color:#848484\nbase_color:#000000\ntext_color:#000000\nselected_bg_color:#f39638\nselected_fg_color:#000000\ntooltip_bg_color:#634110\ntooltip_fg_color:#ffffff" style "theme-default" { xthickness = 10 ythickness = 10 GtkEntry::honors-transparent-bg-hint = 0 GtkMenuItem::arrow-spacing = 20 GtkMenuItem::horizontal-padding = 50 GtkMenuItem::toggle-spacing = 30 GtkOptionMenu::indicator-size = {11, 5} GtkOptionMenu::indicator-spacing = {6, 5, 4, 4} GtkTreeView::horizontal_separator = 5 GtkTreeView::odd_row_color = "#efefef" GtkTreeView::even_row_color = "#e3e3e3" GtkWidget::link-color = "#0062dc" # blue GtkWidget::visited-link-color = "#8c00dc" #purple GtkButton::default_border = { 0, 0, 0, 0 } GtkButton::child-displacement-x = 0 GtkButton::child-displacement-y = 1 GtkWidget::focus-padding = 0 GtkRange::trough-border = 0 GtkRange::slider-width = 19 GtkRange::stepper-size = 19 GtkScrollbar::min_slider_length = 36 GtkScrollbar::has-secondary-backward-stepper = 1 GtkPaned::handle_size = 8 GtkMenuBar::internal-padding = 0 GtkTreeView::expander_size = 13 #15 GtkExpander::expander_size = 13 #17 GtkScale::slider-length = 35 GtkScale::slider-width = 17 GtkScale::trough-border = 0 GtkWidget::link-color = "#0062dc" GtkWidget::visited-link-color = "#8c00dc" #purple WnckTasklist::fade-overlay-rect = 0 WnckTasklist::fade-loop-time = 5.0 # 5 seconds WnckTasklist::fade-opacity = 0.5 # final opacity #makes menu only overlap border GtkMenu::horizontal-offset = -1 #removes extra padding at top and bottom of menus. Makes menuitem overlap border GtkMenu::vertical-padding = 0 #set to the same as roundness, used for better hotspot selection of tabs GtkNotebook::tab-curvature = 2 GtkNotebook::tab-overlap = 4 GtkMenuItem::arrow-spacing = 10 GtkOptionMenu ::indicator-size = {11, 5} GtkCheckButton ::indicator-size = 16 GtkCheckButton ::indicator-spacing = 1 GtkRadioButton ::indicator-size = 16 GtkTreeView::horizontal_separator = 2 GtkTreeView::odd_row_color = "#efefef" GtkTreeView::even_row_color = "#e3e3e3" NautilusIconContainer::normal_icon_color = "#ff0000" GtkEntry::inner-border = {0, 0, 0, 0} GtkScrolledWindow::scrollbar-spacing = 0 GtkScrolledWindow::scrollbars-within-bevel = 1 fg[NORMAL] = @fg_color fg[ACTIVE] = @fg_color fg[PRELIGHT] = @fg_color fg[SELECTED] = @selected_fg_color fg[INSENSITIVE] = shade (3.0,@fg_color) bg[NORMAL] = @bg_color bg[ACTIVE] = shade (0.95,@bg_color) bg[PRELIGHT] = mix(0.92, shade (1.1,@bg_color), @selected_bg_color) bg[SELECTED] = @selected_bg_color bg[INSENSITIVE] = shade (1.06,@bg_color) base[NORMAL] = @base_color base[ACTIVE] = shade (0.65,@base_color) base[PRELIGHT] = @base_color base[SELECTED] = @selected_bg_color base[INSENSITIVE] = shade (1.025,@bg_color) text[NORMAL] = @text_color text[ACTIVE] = shade (0.95,@base_color) text[PRELIGHT] = @text_color text[SELECTED] = @selected_fg_color text[INSENSITIVE] = mix (0.675,shade (0.95,@bg_color),@fg_color) } style "theme-entry" { xthickness = 10 ythickness = 10 GtkEntry::inner-border = {10, 10, 10, 10} GtkEntry::progress-border = {10, 10, 10, 10} GtkEntry::icon-prelight = 1 GtkEntry::state-hintt = 1 #GtkEntry::honors-transparent-bg-hint = 1 text[NORMAL] = "#000000" text[ACTIVE] = "#787878" text[INSENSITIVE] = "#787878" text[SELECTED] = "#FFFFFF" engine "pixmap" { image { function = FLAT_BOX state = NORMAL recolorable = FALSE file = "./backgrounds/entry_background.png" border = { 0, 0, 0, 0 } stretch = TRUE } image { function = FLAT_BOX state = PRELIGHT recolorable = FALSE file = "./backgrounds/entry_background.png" border = { 0, 0, 0, 0 } stretch = TRUE } image { function = FLAT_BOX state = ACTIVE recolorable = FALSE file = "./backgrounds/entry_background.png" border = { 0, 0, 0, 0 } stretch = TRUE } } } #----------------------------------------------- #Chat Balloon Incoming background. style "theme-event-box-top-in" { xthickness = 1 ythickness = 1 GtkEventBox::inner-border = {0, 0, 0, 0} engine "pixmap" { image { function = FLAT_BOX state = NORMAL recolorable = TRUE file = "./backgrounds/chat_in_top.png" border = { 0, 0, 0, 0 } stretch = TRUE } } } style "theme-event-box-mid-in" { xthickness = 1 ythickness = 1 GtkEventBox::inner-border = {0, 0, 0, 0} engine "pixmap" { image { function = FLAT_BOX state = NORMAL recolorable = TRUE file = "./backgrounds/chat_in_mid.png" border = { 0, 0, 0, 0 } stretch = TRUE } } } style "theme-event-box-bot-in" { xthickness = 1 ythickness = 1 GtkEventBox::inner-border = {0, 0, 0, 0} engine "pixmap" { image { function = FLAT_BOX state = NORMAL recolorable = TRUE file = "./backgrounds/chat_in_bot.png" border = { 0, 0, 0, 0 } stretch = TRUE } } } #----------------------------------------------- #Chat Balloon Outgoing background. style "theme-event-box-top-out" { xthickness = 1 ythickness = 1 GtkEventBox::inner-border = {0, 0, 0, 0} engine "pixmap" { image { function = FLAT_BOX state = NORMAL recolorable = TRUE file = "./backgrounds/chat_out_top.png" border = { 0, 0, 0, 0 } stretch = TRUE } } } style "theme-event-box-mid-out" { xthickness = 1 ythickness = 1 GtkEventBox::inner-border = {0, 0, 0, 0} engine "pixmap" { image { function = FLAT_BOX state = NORMAL recolorable = TRUE file = "./backgrounds/chat_out_mid.png" border = { 0, 0, 0, 0 } stretch = TRUE } } } style "theme-event-box-bot-out" { xthickness = 1 ythickness = 1 GtkEventBox::inner-border = {0, 0, 0, 0} engine "pixmap" { image { function = FLAT_BOX state = NORMAL recolorable = TRUE file = "./backgrounds/chat_out_bot.png" border = { 0, 0, 0, 0 } stretch = TRUE } } } style "theme-wide" = "theme-default" { xthickness = 2 ythickness = 2 } style "theme-wider" = "theme-default" { xthickness = 3 ythickness = 3 } style "theme-button" { GtkButton::inner-border = {0, 0, 0, 0} GtkWidget::focus-line-width = 0 GtkWidget::focus-padding = 0 bg[NORMAL] = "#414143" bg[ACTIVE] = "#c19676" bg[PRELIGHT] = "#7f4426" bg[SELECTED] = "#ff0000" bg[INSENSITIVE] = "#434346" fg[NORMAL] = "#ffffff" fg[INSENSITIVE] = "#000000" fg[PRELIGHT] = "#ffffff" fg[SELECTED] = "#ffffff" fg[ACTIVE] = "#ffffff" text[NORMAL] = "#ff0000" text[INSENSITIVE] = "#ff0000" text[PRELIGHT] = "#ff0000" text[SELECTED] = "#ff0000" text[INSENSITIVE] = "#434346" text[ACTIVE] = "#ff0000" base[NORMAL] = "#ff0000" base[INSENSITIVE] = "#ff0000" base[PRELIGHT] = "#ff0000" base[SELECTED] = "#ff0000" base[INSENSITIVE] = "#ff0000" engine "pixmap" { image { function = BOX state = NORMAL recolorable = TRUE file = "./buttons/LightButtonAct.png" border = { 0, 0, 0, 0 } stretch = TRUE } image { function = BOX state = PRELIGHT recolorable = TRUE file = "./buttons/LightButtonRoll.png" border = { 0, 0, 0, 0 } stretch = TRUE } image { function = BOX state = ACTIVE recolorable = TRUE file = "./buttons/LightButtonClicked.png" border = { 0, 0, 0, 0 } stretch = TRUE } image { function = BOX state = INSENSITIVE recolorable = TRUE file = "./buttons/LightButtonInact.png" border = { 0, 0, 0, 0 } stretch = TRUE } } } style "theme-toolbar" { xthickness = 2 ythickness = 2 bg[NORMAL] = shade (1.078,@bg_color) } style "theme-handlebox" { bg[NORMAL] = shade (0.95,@bg_color) } style "theme-scale" { bg[NORMAL] = shade (1.06, @bg_color) bg[PRELIGHT] = mix(0.85, shade (1.1,@bg_color), @selected_bg_color) bg[SELECTED] = "#4d4d55" } style "theme-range" { bg[NORMAL] = shade (1.12,@bg_color) bg[ACTIVE] = @bg_color bg[PRELIGHT] = mix(0.95, shade (1.10,@bg_color), @selected_bg_color) #Arrows text[NORMAL] = shade (0.275,@selected_fg_color) text[PRELIGHT] = @selected_fg_color text[ACTIVE] = shade (0.10,@selected_fg_color) text[INSENSITIVE] = mix (0.80,shade (0.90,@bg_color),@fg_color) } style "theme-notebook" = "theme-wider" { xthickness = 4 ythickness = 4 GtkNotebook::tab-curvature = 5 GtkNotebook::tab-vborder = 1 GtkNotebook::tab-overlap = 1 GtkNotebook::tab-vborder = 1 bg[NORMAL] = "#d2d2d2" bg[ACTIVE] = "#e3e3e3" bg[PRELIGHT] = "#848484" bg[SELECTED] = "#848484" bg[INSENSITIVE] = "#848484" text[PRELIGHT] = @selected_fg_color text[NORMAL] = "#000000" text[ACTIVE] = "#737373" text[SELECTED] = "#000000" text[INSENSITIVE] = "#737373" fg[PRELIGHT] = @selected_fg_color fg[NORMAL] = "#000000" fg[ACTIVE] = "#737373" fg[SELECTED] = "#000000" fg[INSENSITIVE] = "#737373" } style "theme-paned" { bg[PRELIGHT] = shade (1.1,@bg_color) } style "theme-panel" { # Menu fg[PRELIGHT] = @selected_fg_color font_name = "Bold 9" text[PRELIGHT] = @selected_fg_color } style "theme-menu" { xthickness = 0 ythickness = 0 bg[NORMAL] = shade (1.16,@bg_color) bg[SELECTED] = "#ff9a00" text[PRELIGHT] = @selected_fg_color fg[PRELIGHT] = @selected_fg_color } style "theme-menu-item" = "theme-menu" { xthickness = 3 ythickness = 3 base[SELECTED] = "#ff9a00" base[NORMAL] = "#ff9a00" base[PRELIGHT] = "#ff9a00" base[INSENSITIVE] = "#ff9a00" base[ACTIVE] = "#ff9a00" bg[SELECTED] = "#ff9a00" bg[NORMAL] = shade (1.16,@bg_color) } style "theme-menubar" { #TODO } style "theme-menubar-item" = "theme-menu-item" { #TODO bg[SELECTED] = "#ff9a00" } style "theme-tree" { xthickness = 2 ythickness = 1 font_name = "Bold 9" GtkWidget::focus-padding = 0 bg[NORMAL] = "#5a595a" bg[PRELIGHT] = "#5a595a" bg[ACTIVE] = "#5a5a5a" fg[NORMAL] = "#ffffff" fg[ACTIVE] = "#ffffff" fg[SELECTED] = "#ff9a00" fg[PRELIGHT] = "#ffffff" bg[SELECTED] = "#ff9a00" base[SELECTED] = "#ff9a00" base[NORMAL] = "#ff9a00" base[PRELIGHT] = "#ff9a00" base[INSENSITIVE] = "#ff9a00" base[ACTIVE] = "#ff9a00" text[NORMAL] = "#000000" text[PRELIGHT] = "#ff9a00" text[ACTIVE] = "#ff9a00" text[SELECTED] = "#ff9a00" text[INSENSITIVE] = "#434346" } style "theme-tree-arrow" { bg[NORMAL] = mix(0.70, shade (0.60,@bg_color), shade (0.80,@selected_bg_color)) bg[PRELIGHT] = mix(0.80, @bg_color, @selected_bg_color) } style "theme-progressbar" { font_name = "Bold" bg[SELECTED] = @selected_bg_color fg[PRELIGHT] = @selected_fg_color bg[ACTIVE] = "#fe7e00" bg[NORMAL] = "#ffba00" } style "theme-tooltips" = "theme-wider" { font_name = "Liberation sans 10" bg[NORMAL] = @tooltip_bg_color fg[NORMAL] = @tooltip_fg_color text[NORMAL] = @tooltip_fg_color } style "theme-combo" = "theme-button" { xthickness = 4 ythickness = 4 text[NORMAL] = "#fd7d00" text[INSENSITIVE] = "#8a8a8a" base[NORMAL] = "#e0e0e0" base[INSENSITIVE] = "#aeaeae" } style "theme-combo-box" = "theme-button" { xthickness = 3 ythickness = 2 bg[NORMAL] = "#343539" bg[PRELIGHT] = "#343539" bg[ACTIVE] = "#26272b" bg[INSENSITIVE] = "#404145" } style "theme-entry-combo-box" { xthickness = 6 ythickness = 3 text[NORMAL] = "#000000" text[INSENSITIVE] = "#8a8a8a" base[NORMAL] = "#ffffff" base[INSENSITIVE] = "#aeaeae" } style "theme-combo-arrow" = "theme-button" { xthickness = 1 ythickness = 1 } style "theme-view" { xthickness = 0 ythickness = 0 } style "theme-check-radio-buttons" { GtkWidget::interior-focus = 0 GtkWidget::focus-padding = 1 text[NORMAL] = "#ff0000" base[NORMAL] = "#ff0000" text[SELECTED] = "#ffffff" text[INSENSITIVE] = shade (0.625,@bg_color) base[PRELIGHT] = mix(0.80, @base_color, @selected_bg_color) bg[NORMAL] = "#438FC6" bg[INSENSITIVE] = "#aeaeae" bg[SELECTED] = "#ff8a01" } style "theme-radio-buttons" = "theme-button" { GtkWidget::interior-focus = 0 GtkWidget::focus-padding = 1 text[SELECTED] = @selected_fg_color text[INSENSITIVE] = shade (0.625,@bg_color) base[PRELIGHT] = mix(0.80, @base_color, @selected_bg_color) bg[NORMAL] = "#ffffff" bg[INSENSITIVE] = "#dcdcdc" bg[SELECTED] = @selected_bg_color } style "theme-spin-button" { bg[NORMAL] = "#d2d2d2" bg[ACTIVE] = "#868686" bg[PRELIGHT] = "#7f4426" bg[SELECTED] = shade(1.10,@selected_bg_color) bg[INSENSITIVE] = "#dcdcdc" base[NORMAL] = "#ffffff" base[INSENSITIVE] = "#dcdcdc" text[NORMAL] = "#000000" text[INSENSITIVE] = "#aeaeae" } style "theme-calendar" { xthickness = 0 ythickness = 0 bg[NORMAL] = "#676767" bg[PRELIGHT] = shade(0.92,@bg_color) bg[ACTIVE] = "#ff0000" bg[INSENSITIVE] = "#ff0000" bg[SELECTED] = "#ff0000" text[PRELIGHT] = "#000000" text[NORMAL] = "#000000" text[INSENSITIVE]= "#000000" text[SELECTED] = "#ffffff" text[ACTIVE] = "#000000" fg[NORMAL] = "#ffffff" fg[PRELIGHT] = "#ffffff" fg[INSENSITIVE] = "#ffffff" fg[SELECTED] = "#ffffff" fg[ACTIVE] = "#ffffff" base[NORMAL] = "#ff0000" base[NORMAL] = "#aeaeae" base[INSENSITIVE] = "#00ff00" base[SELECTED] = "#f3720d" base[ACTIVE] = "#f3720d" } style "theme-separator-menu-item" { xthickness = 1 ythickness = 0 GtkSeparatorMenuItem::horizontal-padding = 2 # We are setting the desired height by using wide-separators # There is no other way to get the odd height ... GtkWidget::wide-separators = 1 GtkWidget::separator-width = 1 GtkWidget::separator-height = 5 } style "theme-frame" { xthickness = 10 ythickness = 0 GtkWidget::LABEL-SIDE-PAD = 14 GtkWidget::LABEL-PAD = 23 fg[NORMAL] = "#000000" fg[ACTIVE] = "#000000" fg[PRELIGHT] = "#000000" fg[SELECTED] = "#000000" fg[INSENSITIVE] = "#000000" bg[NORMAL] = "#e2e2e2" bg[ACTIVE] = "#000000" bg[PRELIGHT] = "#000000" bg[SELECTED] = "#000000" bg[INSENSITIVE] = "#000000" base[NORMAL] = "#000000" base[ACTIVE] = "#000000" base[PRELIGHT] = "#000000" base[SELECTED] = "#000000" base[INSENSITIVE]= "#000000" text[NORMAL] = "#000000" text[ACTIVE] = "#000000" text[PRELIGHT] = "#000000" text[SELECTED] = "#000000" text[INSENSITIVE]= "#000000" } style "theme-textview" { text[NORMAL] = "#000000" text[ACTIVE] = "#000000" text[PRELIGHT] = "#000000" text[SELECTED] = "#000000" text[INSENSITIVE] = "#434648" bg[NORMAL] = "#ffffff" bg[ACTIVE] = "#ffffff" bg[PRELIGHT] = "#ffffff" bg[SELECTED] = "#ffffff" bg[INSENSITIVE] = "#ffffff" fg[NORMAL] = "#ffffff" fg[ACTIVE] = "#ffffff" fg[PRELIGHT] = "#ffffff" fg[SELECTED] = "#ffffff" fg[INSENSITIVE] = "#ffffff" base[NORMAL] = "#ffffff" base[ACTIVE] = "#ffffff" base[PRELIGHT] = "#ffffff" base[SELECTED] = "#ff9a00" base[INSENSITIVE] = "#ffffff" } style "theme-clist" { text[NORMAL] = "#000000" text[ACTIVE] = "#000000" text[PRELIGHT] = "#000000" text[SELECTED] = "#000000" text[INSENSITIVE] = "#434648" bg[NORMAL] = "#353438" bg[ACTIVE] = "#ff9a00" bg[PRELIGHT] = "#ff9a00" bg[SELECTED] = "#ff9a00" bg[INSENSITIVE] = "#ffffff" fg[NORMAL] = "#000000" fg[ACTIVE] = "#ff9a00" fg[PRELIGHT] = "#ff9a00" fg[SELECTED] = "#fdff00" fg[INSENSITIVE] = "#757575" base[NORMAL] = "#ffffff" base[ACTIVE] = "#fdff00" base[PRELIGHT] = "#000000" base[SELECTED] = "#fdff00" base[INSENSITIVE] = "#757575" } style "theme-label" { bg[NORMAL] = "#414143" bg[ACTIVE] = "#c19676" bg[PRELIGHT] = "#7f4426" bg[SELECTED] = "#000000" bg[INSENSITIVE] = "#434346" fg[NORMAL] = "#000000" fg[INSENSITIVE] = "#434346" fg[PRELIGHT] = "#000000" fg[SELECTED] = "#000000" fg[ACTIVE] = "#000000" text[NORMAL] = "#ffffff" text[INSENSITIVE] = "#434346" text[PRELIGHT] = "#ffffff" text[SELECTED] = "#ffffff" text[ACTIVE] = "#ffffff" base[NORMAL] = "#000000" base[INSENSITIVE] = "#00ff00" base[PRELIGHT] = "#0000ff" base[ACTIVE] = "#f39638" } style "theme-button-label" { bg[NORMAL] = "#414143" bg[ACTIVE] = "#c19676" bg[PRELIGHT] = "#7f4426" bg[SELECTED] = "#000000" bg[INSENSITIVE] = "#434346" fg[NORMAL] = "#ffffff" fg[INSENSITIVE] = "#434346" fg[PRELIGHT] = "#ffffff" fg[SELECTED] = "#ffffff" fg[ACTIVE] = "#ffffff" text[NORMAL] = "#000000" text[INSENSITIVE] = "#434346" text[PRELIGHT] = "#000000" text[SELECTED] = "#000000" text[ACTIVE] = "#000000" base[NORMAL] = "#000000" base[INSENSITIVE] = "#00ff00" base[PRELIGHT] = "#0000ff" base[SELECTED] = "#ff00ff" base[ACTIVE] = "#ffff00" } style "theme-button-check-radio-label" { bg[NORMAL] = "#414143" bg[ACTIVE] = "#c19676" bg[PRELIGHT] = "#7f4426" bg[SELECTED] = "#000000" bg[INSENSITIVE] = "#434346" fg[NORMAL] = "#000000" fg[INSENSITIVE] = "#434346" fg[PRELIGHT] = "#000000" fg[SELECTED] = "#000000" fg[ACTIVE] = "#000000" text[NORMAL] = "#ffffff" text[INSENSITIVE] = "#434346" text[PRELIGHT] = "#ffffff" text[SELECTED] = "#000000" text[ACTIVE] = "#ffffff" base[NORMAL] = "#000000" base[INSENSITIVE] = "#00ff00" base[PRELIGHT] = "#0000ff" base[SELECTED] = "#ff00ff" base[ACTIVE] = "#ffff00" } style "theme-table" { bg[NORMAL] = "#848484" bg[ACTIVE] = "#c19676" bg[PRELIGHT] = "#7f4426" bg[SELECTED] = "#000000" bg[INSENSITIVE] = "#434346" } style "theme-iconview" { GtkWidget::focus-line-width=1 bg[NORMAL] = "#000000" bg[ACTIVE] = "#c19676" bg[PRELIGHT] = "#c19676" bg[SELECTED] = "#c19676" bg[INSENSITIVE] = "#969696" fg[NORMAL] = "#ffffff" fg[INSENSITIVE] = "#ffffff" fg[PRELIGHT] = "#ffffff" fg[SELECTED] = "#ffffff" fg[ACTIVE] = "#ffffff" text[NORMAL] = "#000000" text[INSENSITIVE] = "#434346" text[PRELIGHT] = "#000000" text[SELECTED] = "#000000" text[ACTIVE] = "#000000" base[NORMAL] = "#ffffff" base[INSENSITIVE] = "#434346" base[PRELIGHT] = "#FAD184" base[SELECTED] = "#FAD184" base[ACTIVE] = "#FAD184" } # Set Widget styles class "GtkWidget" style "theme-default" class "GtkScale" style "theme-scale" class "GtkRange" style "theme-range" class "GtkPaned" style "theme-paned" class "GtkFrame" style "theme-frame" class "GtkMenu" style "theme-menu" class "GtkMenuBar" style "theme-menubar" class "GtkEntry" style "theme-entry" class "GtkProgressBar" style "theme-progressbar" class "GtkToolbar" style "theme-toolbar" class "GtkSeparator" style "theme-wide" class "GtkCalendar" style "theme-calendar" class "GtkTable" style "theme-table" widget_class "*<GtkMenuItem>*" style "theme-menu-item" widget_class "*<GtkMenuBar>.<GtkMenuItem>*" style "theme-menubar-item" widget_class "*<GtkSeparatorMenuItem>*" style "theme-separator-menu-item" widget_class "*<GtkLabel>" style "theme-label" widget_class "*<GtkButton>" style "theme-button" widget_class "*<GtkButton>*<GtkLabel>*" style "theme-button-label" widget_class "*<GtkCheckButton>" style "theme-check-radio-buttons" widget_class "*<GtkToggleButton>.<GtkLabel>*" style "theme-button" widget_class "*<GtkCheckButton>.<GtkLabel>*" style "theme-button-check-radio-label" widget_class "*<GtkRadioButton>.<GtkLabel>*" style "theme-button-check-radio-label" widget_class "*<GtkTextView>" style "theme-textview" widget_class "*<GtkList>" style "theme-textview" widget_class "*<GtkCList>" style "theme-clist" widget_class "*<GtkIconView>" style "theme-iconview" widget_class "*<GtkHandleBox>" style "theme-handlebox" widget_class "*<GtkNotebook>" style "theme-notebook" widget_class "*<GtkNotebook>*<GtkEventBox>" style "theme-notebook" widget_class "*<GtkNotebook>*<GtkDrawingArea>" style "theme-notebook" widget_class "*<GtkNotebook>*<GtkLayout>" style "theme-notebook" widget_class "*<GtkNotebook>*<GtkViewport>" style "theme-notebook" widget_class "*<GtkNotebook>.<GtkLabel>*" style "theme-notebook" #for tabs # Combo Box Stuff widget_class "*<GtkCombo>*" style "theme-combo" widget_class "*<GtkComboBox>*<GtkButton>" style "theme-combo-box" widget_class "*<GtkComboBoxEntry>*" style "theme-entry-combo-box" widget_class "*<GtkSpinButton>*" style "theme-spin-button" widget_class "*<GtkSpinButton>*<GtkArrow>*" style:highest "theme-tree-arrow" # Tool Tips Stuff widget "gtk-tooltip*" style "theme-tooltips" # Tree View Stuff widget_class "*<GtkTreeView>.<GtkButton>*" style "theme-tree" widget_class "*<GtkCTree>.<GtkButton>*" style "theme-tree" widget_class "*<GtkList>.<GtkButton>*" style "theme-tree" widget_class "*<GtkCList>.<GtkButton>*" style "theme-tree" # For arrow bg widget_class "*<GtkTreeView>.<GtkButton>*<GtkArrow>" style "theme-tree-arrow" widget_class "*<GtkCTree>.<GtkButton>*<GtkArrow>" style "theme-tree-arrow" widget_class "*<GtkList>.<GtkButton>*<GtkArrow>" style "theme-tree-arrow" ####################################################### ## GNOME specific ####################################################### widget_class "*.ETree.ECanvas" style "theme-tree" widget_class "*.ETable.ECanvas" style "theme-tree" style "panelbuttons" = "theme-button" { # As buttons are draw lower this helps center text xthickness = 3 ythickness = 3 } widget_class "*Panel*<GtkButton>*" style "panelbuttons" style "murrine-fg-is-text-color-workaround" { text[NORMAL] = "#000000" text[ACTIVE] = "#fdff00" text[SELECTED] = "#fdff00" text[INSENSITIVE] = "#757575" bg[SELECTED] = "#b85e03" bg[ACTIVE] = "#b85e03" bg[SELECTED] = "#b85e03" fg[SELECTED] = "#ffffff" fg[NORMAL] = "#ffffff" fg[ACTIVE] = "#ffffff" fg[INSENSITIVE] = "#434348" fg[PRELIGHT] = "#ffffff" base[SELECTED] = "#ff9a00" base[NORMAL] = "#ffffff" base[ACTIVE] = "#ff9a00" base[INSENSITIVE] = "#434348" base[PRELIGHT] = "#ffffff" } widget_class "*.<GtkTreeView>*" style "murrine-fg-is-text-color-workaround" style "murrine-combobox-text-color-workaround" { text[NORMAL] = "#FFFFF" text[PRELIGHT] = "#FFFFF" text[SELECTED] = "#FFFFF" text[ACTIVE] = "#FFFFF" text[INSENSITIVE] = "#FFFFF" } widget_class "*.<GtkComboBox>.<GtkCellView>" style "murrine-combobox-text-color-workaround" style "murrine-menuitem-text-is-fg-color-workaround" { bg[NORMAL] = "#0000ff" text[NORMAL] = "#ffffff" text[PRELIGHT] = "#ffffff"#"#FD7D00" text[SELECTED] = "#ffffff"#"#ff0000"# @selected_fg_color text[ACTIVE] = "#ffffff"#"#ff0000"# "#FD7D00" text[INSENSITIVE] = "#ffffff"#ff0000"# "#414143" } widget "*.gtk-combobox-popup-menu.*" style "murrine-menuitem-text-is-fg-color-workaround"

    Read the article

  • Geek Fun: Virtualized Old School Windows – Windows 95

    - by Matthew Guay
    Last week we enjoyed looking at Windows 3.1 running in VMware Player on Windows 7.  Today, let’s upgrade our 3.1 to 95, and get a look at how most of us remember Windows from the 90’s. In this demo, we’re running the first release of Windows 95 (version 4.00.950) in VMware Player 3.0 running on Windows 7 x64.  For fun, we ran the 95 upgrade on the 3.1 virtual machine we built last week. Windows 95 So let’s get started.  Here’s the first setup screen.  For the record, Windows 95 installed in about 15 minutes or less in VMware in our test. Strangely, Windows 95 offered several installation choices.  They actually let you choose what extra parts of Windows to install if you wished.  Oh, and who wants to run Windows 95 on your “Portable Computer”?  Most smartphones today are more powerful than the “portable computers” of 95. Your productivity may vastly increase if you run Windows 95.  Anyone want to switch? No, I don’t want to restart … I want to use my computer! Welcome to Windows 95!  Hey, did you know you can launch programs from the Start button? Our quick spin around Windows 95 reminded us why Windows got such a bad reputation in the ‘90’s for being unstable.  We didn’t even get our test copy fully booted after installation before we saw our first error screen.  Windows in space … was that the most popular screensaver in Windows 95, or was it just me? Hello Windows 3.1!  The UI was still outdated in some spots.   Ah, yes, Media Player before it got 101 features to compete with iTunes. But, you couldn’t even play CDs in Media Player.  Actually, CD player was one program I used almost daily in Windows 95 back in the day. Want some new programs?  This help file about new programs designed for Windows 95 lists a lot of outdated names in tech.    And, you really may want some programs.  The first edition of Windows 95 didn’t even ship with Internet Explorer.   We’ve still got Minesweeper, though! My Computer had really limited functionality, and by default opened everything in a new window.  Double click on C:, and it opens in a new window.  Ugh. But Explorer is a bit more like more modern versions. Hey, look, Start menu search!  If only it found the files you were looking for… Now I’m feeling old … this shutdown screen brought back so many memories … of shutdowns that wouldn’t shut down! But, you still have to turn off your computer.  I wonder how many old monitors had these words burned into them? So there’s yet another trip down Windows memory lane.  Most of us can remember using Windows 95, so let us know your favorite (or worst) memory of it!  At least we can all be thankful for our modern computers and operating systems today, right?  Similar Articles Productive Geek Tips Geek Fun: Remember the Old-School SkiFree Game?Geek Fun: Virtualized old school Windows 3.11Stupid Geek Tricks: Tile or Cascade Multiple Windows in Windows 7Stupid Geek Tricks: Select Multiple Windows on the TaskbarHow to Delete a System File in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

    Read the article

  • Geek Fun: Virtualized Old School Windows – Windows 95

    - by Matthew Guay
    Last week we enjoyed looking at Windows 3.1 running in VMware Player on Windows 7.  Today, let’s upgrade our 3.1 to 95, and get a look at how most of us remember Windows from the 90’s. In this demo, we’re running the first release of Windows 95 (version 4.00.950) in VMware Player 3.0 running on Windows 7 x64.  For fun, we ran the 95 upgrade on the 3.1 virtual machine we built last week. Windows 95 So let’s get started.  Here’s the first setup screen.  For the record, Windows 95 installed in about 15 minutes or less in VMware in our test. Strangely, Windows 95 offered several installation choices.  They actually let you choose what extra parts of Windows to install if you wished.  Oh, and who wants to run Windows 95 on your “Portable Computer”?  Most smartphones today are more powerful than the “portable computers” of 95. Your productivity may vastly increase if you run Windows 95.  Anyone want to switch? No, I don’t want to restart … I want to use my computer! Welcome to Windows 95!  Hey, did you know you can launch programs from the Start button? Our quick spin around Windows 95 reminded us why Windows got such a bad reputation in the ‘90’s for being unstable.  We didn’t even get our test copy fully booted after installation before we saw our first error screen.  Windows in space … was that the most popular screensaver in Windows 95, or was it just me? Hello Windows 3.1!  The UI was still outdated in some spots.   Ah, yes, Media Player before it got 101 features to compete with iTunes. But, you couldn’t even play CDs in Media Player.  Actually, CD player was one program I used almost daily in Windows 95 back in the day. Want some new programs?  This help file about new programs designed for Windows 95 lists a lot of outdated names in tech.    And, you really may want some programs.  The first edition of Windows 95 didn’t even ship with Internet Explorer.   We’ve still got Minesweeper, though! My Computer had really limited functionality, and by default opened everything in a new window.  Double click on C:, and it opens in a new window.  Ugh. But Explorer is a bit more like more modern versions. Hey, look, Start menu search!  If only it found the files you were looking for… Now I’m feeling old … this shutdown screen brought back so many memories … of shutdowns that wouldn’t shut down! But, you still have to turn off your computer.  I wonder how many old monitors had these words burned into them? So there’s yet another trip down Windows memory lane.  Most of us can remember using Windows 95, so let us know your favorite (or worst) memory of it!  At least we can all be thankful for our modern computers and operating systems today, right?  Similar Articles Productive Geek Tips Geek Fun: Remember the Old-School SkiFree Game?Geek Fun: Virtualized old school Windows 3.11Stupid Geek Tricks: Tile or Cascade Multiple Windows in Windows 7Stupid Geek Tricks: Select Multiple Windows on the TaskbarHow to Delete a System File in Windows 7 or Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

    Read the article

  • How to Animate Text and Objects in PowerPoint 2010

    - by DigitalGeekery
    Are you looking for an eye catching way to keep your audience interested in your PowerPoint presentations? Today we’ll take a look at how to add animation effects to objects in PowerPoint 2010. Select the object you wish to animate and then click the More button in the Animation group of the Animation tab.   Animations are grouped into four categories. Entrance effects, Exit effects, Emphasis effects, and Motion Paths. You can get a Live Preview of how the animation will look by hovering your mouse over an animation effect.   When you select a Motion Path, your object will move along the dashed path line as shown on the screen. (This path is not displayed in the final output) Certain aspects of the Motion Path effects are editable. When you apply a Motion Path animation to an object, you can select the path and drag the end to change the length or size of the path. The green marker along the motion path marks the beginning of the  path and the red marks the end. The effects can be rotated by clicking and the bar near the center of the effect.   You can display additional effects by choosing one of the options at the bottom. This will pop up a Change Effect window. If you have Preview Effect checked at the lower left you can preview the effects by single clicking.   Apply Multiple Animations to an Object Select the object and then click the Add Animation button to display the animation effects. Just as we did with the first effect, you can hover over to get a live preview. Click to apply the effect. The animation effects will happen in the order they are applied. Animation Pane You can view a list of the animations applied to a slide by opening the Animation Pane. Select the Animation Pane button from the Advanced Animation group to display the Animation Pane on the right. You’ll see that each animation effect in the animation pane has an assigned number to the left.    Timing Animation Effects You can change when your animation starts to play. By default it is On Click. To change it, select the effect in the Animation Pane and then choose one of the options from the Start dropdown list. With Previous starts at the same time as the previous animation and After Previous starts after the last animation. You can also edit the duration that the animations plays and also set a delay.   You can change the order in which the animation effects are applied by selecting the effect in the animation pane and clicking Move Earlier or Move Later from the Timing group on the Animation tab. Effect Options If the Effect Options button is available when your animation is selected, then that particular animation has some additional effect settings that can be configured. You can access the Effect Option by right-clicking on the the animation in the Animation Pane, or by selecting Effect Options on the ribbon.   The available options will vary by effect and not all animation effects will have Effect Options settings. In the example below, you can change the amount of spinning and whether the object will spin clockwise or counterclockwise.   Under Enhancements, you can add sound effects to your animation. When you’re finished click OK.   Animating Text Animating Text works the same as animating an object. Simply select your text box and choose an animation. Text does have some different Effect Options. By selecting a sequence, you decide whether the text appears as one object, all at once, or by paragraph. As is the case with objects, there will be different available Effect Options depending on the animation you choose. Some animations, such as the Fly In animation, will have directional options.   Testing Your Animations Click on the Preview button at any time to test how your animations look. You can also select the Play button on the Animation Pane. Conclusion Animation effects are a great way to focus audience attention on important points and hold viewers interest in your PowerPoint presentations. Another cool way to spice up your PPT 2010 presentations is to add video from the web. What tips do you guys have for making your PowerPoint presentations more interesting? Similar Articles Productive Geek Tips Center Pictures and Other Objects in Office 2007 & 2010Preview Before You Paste with Live Preview in Office 2010Embed True Type Fonts in Word and PowerPoint 2007 DocumentsHow to Add Video from the Web in PowerPoint 2010Add Artistic Effects to Your Pictures in Office 2010 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 24 Million Sites Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos Video preview of new Windows Live Essentials

    Read the article

  • Learn About Oracle’s Strategy for a Simple, Modern User Experience at OpenWorld 2012

    - by Applications User Experience
    By Kathy Miedema, Oracle Applications User Experience If you’re interested in what the best possible user experience looks like, you’ll want to hear what Oracle’s Applications User Experience team is planning for OpenWorld 2012, Sept. 30-Oct. 4 in San Francisco. This year, we will talk Fusion, Fusion, Fusion. We were among the first to show Oracle Fusion Applications in the last couple of years, and we’ll be showing it again this year so you can see what Oracle is planning for the next generation of enterprise applications. Attend our sessions to learn more about the user experience strategy in which Oracle is investing. Simplicity is the driving force behind the demos that we are unveiling now, which you can see at OpenWorld. We want to create opportunities for productivity and efficiency, and deliver enterprise data across devices to help you do your work in the way best suited to your job and needs, said Jeremy Ashley, Vice President, Oracle Applications User Experience. You can see the new look for Fusion Applications at a general session led by Ashley at 3:30 p.m. on Wednesday, Oct. 3. You’ll also have the chance to learn more about tailoring in Oracle Fusion Applications, and gain a new understanding of the investment in the user experience behind Fusion Applications at our sessions (see session information below). Inside the Oracle Applications User Experience team’s on-site lab at Oracle OpenWorld 2011. Head to the demogrounds to see new demos from the Applications User Experience team, including the new look for Fusion Applications and what we’re building for mobile platforms. Take a spin on our eye tracker, a very cool tool that we use to research the usability of a particular design. Visit the Usable Apps OpenWorld page to find out where our demopods will be located. We are also recruiting participants for our on-site lab, in which we gather feedback on new user experience designs, and taking reservations for a charter bus that will bring you to Oracle headquarters for a lab tour Thursday, Oct. 4, or Friday, Oct. 5. Tours leave at 10 a.m. and 1:45 p.m. from the Moscone Center in San Francisco. You’ll see more of our newest designs at the lab tour, and some of our research tools in action. Can’t participate in a customer feedback session or take a lab tour this time around? Visit Usable Apps to participate or book a tour another time. For more information on any OpenWorld sessions, check the content catalog – also available at www.oracle.com/openworld. For information on Applications User Experience (Apps UX) sessions and activities, go to the Usable Apps OpenWorld page. APPS UX OPENWORLD SESSIONS Oracle’s Roadmap to a Simple, Modern User Experience Presenter: Jeremy Ashley, Vice President Applications User Experience, Oracle; with Debra Lilley, Fujitsu Consulting; Basheer Khan, Innowave; and Edward Roske, InterRelSession ID: CON9467Date: Wednesday, Oct. 3 Time: 3:30 - 4:30 p.m.Location: Moscone West - 3002/3004 Jeremy Ashley Oracle Fusion Applications: Transforming Insight into Action Presenters: Killian Evers and Kristin Desmond, OracleSession ID: CON8718Date: Thursday, Oct. 4Time: 11:15 a.m. - 12:15 p.m.Location: Moscone West - 2008 “FRIENDS OF UX” OPENWORLD SESSIONS Sessions by the Oracle Usability Advisory Board (OUAB) members: Advances in Oracle Enterprise Governance, Risk, and Compliance Manager  Presenters: Koen Delaure, KPMG Advisory NV, and Oracle Usability Advisory Board member; Russell Stohr, Oracle Session ID: CON9389Date: Tuesday, Oct. 2Time: 1:15 - 2:15 p.m.Location: Palace Hotel - Concert Optimize Oracle E-Busines Suite Procure-to-Pay: Cut Inefficiences/Fraud with Oracle GRC Apps Presenters: Koen Delaure, KPMG Advisory NV, and Solveig Wagner, Seadrill Management AS, both Oracle Usability Advisory Board members; and Swarnali Bag, OracleSession ID: CON9401Date: Monday, Oct. 1Time: 12:15 - 1:15 p.m.Location: Intercontinental - Sutter Showcase of JD Edwards EnterpriseOne Mobility Presenters: Jon Wells, Westmoreland Coal Co., Oracle Usability Advisory Board member; Rob Mills and Liz Davson, Town of Oakville; Keith Sholes and Louise Farner, Oracle Session ID: CON9123Date: Tuesday, Oct. 2Time: 1:15 - 2:15 p.m.Location: InterContinental - Grand Ballroom B Sessions by the Fusion User Experience Adovcates (FXA) Usability and Features of Oracle Fusion Applications, Built upon Oracle Fusion Middleware Presenters: Debra Lilley, Fujitsu Consulting and Oracle Usability Advisory Board member; John King, King Training ResourcesSession ID: UGF10371Date: Sunday, Sept. 30Time: 11 a.m. - 11:45 a.m. Location: Moscone West – 2010 Ten Things to Love About Oracle Fusion Project Portfolio Management  Presenter: Floyd Teter, EiS TechnologiesSession ID: CON6021Date: Tuesday, Oct. 2Time: 10:15 - 11:15 a.m.Location: Moscone West – 2003

    Read the article

  • Killing Stuck Child JVM's

    - by ACShorten
    Note: This facility only applies to Oracle Utilities Application Framework products using COBOL. In some situations, the Child JVM's may spin. This causes multiple startup/shutdown Child JVM messages to be displayed and recursive child JVM's to be initiated and shunned. If the following: Unable to establish connection on port …. after waiting .. seconds.The issue can be caused intermittently by CPU spins in connection to the creation of new processes, specifically Child JVMs. Recursive (or double) invocation of the System.exit call in the remote JVM may be caused by a Process.destroy call that the parent JVM always issues when shunning a JVM. The issue may happen when the thread in the parent JVM that is responsible for the recycling gets stuck and it affects all child JVMs. If this issue occurs at your site then there are a number of options to address the issue: Configure an Operating System level kill command to force the Child JVM to be shunned when it becomes stuck. Configure a Process.destroy command to be used if the kill command is not configured or desired. Specify a time tolerance to detect stuck threads before issuing the Process.destroy or kill commands. Note: This facility is also used when the Parent JVM is also shutdown to ensure no zombie Child JVM's exit. The following additional settings must be added to the spl.properties for the Business Application Server to use this facility: spl.runtime.cobol.remote.kill.command – Specify the command to kill the Child JVM process. This can be a command or specify a script to execute to provide additional information. The kill.command property can accept two arguments, {pid} and {jvmNumber}, in the specified string. The arguments must be enclosed in curly braces as shown here. Note: The PID will be appended to the killcmd string, unless the {pid} and {jvmNumber} arguments are specified. The jvmNumber can be useful if passed to a script for logging purposes. Note: If a script is used it must be in the path and be executable by the OS user running the system. spl.runtime.cobol.remote.destroy.enabled – Specify whether to use the Process.destroy command instead of the kill command. Specify true or false. Default value is false. Note: Unless otherwise required, it is recommended to use the kill command option if shunning JVM's is an issue. There this value can remain its default value, false, unless otherwise required. spl.runtime.cobol.remote.kill.delaysecs – Specify the number of seconds to wait for the Child JVM to terminate naturally before issuing the Process.destroy or kill commands. Default is 10 seconds. For example: spl.runtime.cobol.remote.kill.command=kill -9 {pid} {jvmNumber}spl.runtime.cobol.remote.destroy.enabled=falsespl.runtime.cobol.remote.kill.delaysecs=10 When a Child JVM is to be recycled, these properties are inspected and the spl.runtime.cobol.remote.kill.command, executed if provided. This is done after waiting for spl.runtime.cobol.remote.kill.delaysecs seconds to give the JVM time to shut itself down. The spl.runtime.cobol.remote.destroy.enabled property must be set to true AND the spl.runtime.cobol.remote.kill.command omitted for the original Process.destroy command to be used on the process. Note: By default the spl.runtime.cobol.remote.destroy enabled is set to false and is therefore disabled. If neither spl.runtime.cobol.remote.kill.command nor spl.runtime.cobol.remote.destroy.enabled is specified, child JVMs will not beforcibly killed. They will be left to shut themselves down (which may lead to orphan JVMs). If both are specified, the spl.runtime.cobol.remote.kill.command is preferred and spl.runtime.cobol.remote.destroy.enabled defaulted to false.It is recommended to invoke a script to issue the direct kill command instead of directly using the kill -9 commands.For example, the following sample script ensures that the process Id is an active cobjrun process before issuing the kill command: forcequit.sh #!/bin/shTHETIME=`date +"%Y-%m-%d %H:%M:%S"`if [ "$1" = "" ]then  echo "$THETIME: Process Id is required" >>$SPLSYSTEMLOGS/forcequit.log  exit 1fijavaexec=cobjrunps e $1 | grep -c $javaexecif [ $? = 0 ]then  echo "$THETIME: Process $1 is an active $javaexec process -- issuing kill-9 $1" >>$SPLSYSTEMLOGS/forcequit.log  kill -9 $1exit 0else  echo "$THETIME: Process id $1 is not a $javaexec process or not active --  kill will not be issued" >>$SPLSYSTEMLOGS/forcequit.logexit 1fi This script's name would then be specified as the value for the spl.runtime.cobol.remote.kill.command property, for example: spl.runtime.cobol.remote.kill.command=forcequit.sh The forcequit script does not have any explicit parameters but pid is passed automatically. To use the jvmNumber parameter it must explicitly specified in the command. For example, to call script forcequit.sh and pass it the pid and the child JVM number, specify it as follows: spl.runtime.cobol.remote.kill.command=forcequit.sh {pid} {jvmNumber} The script can then use the JVM number for logging purposes or to further ensure that the correct pid is being killed.If the arguments are omitted, the pid is automatically appended to the spl.runtime.cobol.remote.kill.command string. To use this facility the following patches must be installed: Patch 13719584 for Oracle Utilities Application Framework V2.1, Patches 13684595 and 13634933 for Oracle Utilities Application Framework V2.2 Group Fix 4 (as Patch 13640668) for Oracle Utilities Application Framework V4.1.

    Read the article

  • Happy 3rd Birthday SilverlightCream!

    - by Dave Campbell
    Happy 3rd Birthday!     Yesterday (May 16) was the 'Birthday' of SilverlightCream, which started just after MIX in 2007 with a post "Interesting Silverlight posts today: Silverlight Control & Silverlight Pad". Too many good posts flying around led me to want to archive them, particularly since I was being aggregated at a new site Silverlight.net, and I could give some of that 'reach' to the community. Saturday's post was number 862, and as of that post, there were 5697 blog posts archived in the database all tagged up and searchable at SilverlightCream.com using the search page. The search needs to be better, and that's another discussion, but it does work. The blog didn't begin life as the SilverlightCream blog, as is obvious from the name, but once I realized people were following it closely, I've tried to keep the signal-to-noise ratio very high. I even secured another blog for when I just want to rant about something to keep that stuff out of this one :) If you've been around since MIX07 days you've heard all this, but after talking to some people at MIX10 I realized not everyone knows all the ways the information is presented, so I figured doing a post like this once a year probably isn't a bad idea :) I scrounge through an ever-growing list of blogs (right now sitting at 505) looking for good stuff. I try to spin through the list every day, but with the list growing that large, it's getting tough. I usually use it as a background task while working or watching TV. If I just sit and go through the blogs it takes about an hour. The list is long enough now that from time to time, I'll only get partway through it and have 10 to 13 entries, so I'll just stop there and go on the next day... I don't like to have more than 15 in any single post. It's all pattern recognition as in "seen that", "seen that", "that's new", etc... so if you're a blogger, look at a heading below for some comments about blogging from my perspective. When I see something new, I make sure you're not pulling a 'Mike Taulty' on me and dumping 6 or 8 new posts in one day :), and I tag the ones I want to review. If there's not a lot going on, I may just push the posts as I come across them. Some days there may be 60 posts in that 'to review' list! Some are non-Silverlight, some are essentially duplicates of others, some are demos, ads, new releases of something, session materials, etc. I push lots of material into a database at WynApse.com, and the "Tagged Posts" menu on the left sidebar there takes you to a tag cloud of (at this very moment) "9224 articles tagged 13915 different ways using 459 unique tags". There are links in there on Gibson guitars, Jazz Guitar instructional stuff, Ford F-250 links, and tons of technical and non-technical stuff I've been aggregating for about 5 years now. So when I decide to blog (or shoutout) something, I first push it into the database at WynApse.com. Then I tag it all up and push it into the database at SilverlightCream.com. Then it gets pushed to @SilverlightNews. For a little over a year now, we're tracking unique IP hits on posts launched from either the blog post or from one of the SilverlightCream.com pages, and the posts with top hits from unique IP addresses in the last 7 days are displayed in a 'Skim' page at SilverlightCream... and that page needs work as well. The Skim page and tracking was the brainchild of my buddy Michael Washington. What I blog/shoutout After some time doing posts, I decided there were things that probably have no need to be searchable, but are good information, so I post those as 'Shoutouts'. Eventually I also decided the Shoutouts should get posted to @SilverlightNews, and that's now taking place. Notes to bloggers Remember I said spinning throught the Big List-o-BlogsTM is pattern recognition... that means I don't spend a lot of time on any individual blog deciding if it has new content. If you're familiar with the term 'Above the Fold', then you're probably ok. If I have to scroll the page to see if there's something new, or wade through some maze of menus, I'm probably going to miss new stuff. Likewise if you only show the latest on the front page and make it a puzzle to find the rest of them, or if you make the titles and initial graphics almost identical to the previous article, I'll miss it. Another thing is name/brand-recognition. Far be it for me (WynApse) to comment on someone blogging with a pseudonym, but if you want to get get some recognition, you are going to want your name to be available somewhere. I can think right off the top of my head of a couple good blogs that I have no idea of the individuals' real names. I can pull that off a bit because I've been around so long almost everyone knows who I am, but if you're new to the blog-o-sphere, being able to be name-recognized is as important as getting your brand out there. Kick my tires Finally, stuff happens... I may hit the wrong key and delete your blog, or a post might slip past me and I not realize it's new because of the naming, and never blog it. If you think I missed something, send me an email or use the submit page at SilverlightCream.com. Some bloggers have figured out that if they submit (one way or another) to me, their posts will go out next. I try to honor anyone that takes the time to submit with a quicker 'Cream posting. Thanks! Finally, thanks to everyone that contributes to the community as a whole... the blogs, the videos, and the presentations. A special thanks to everyone that reads SilverlightCream, or follows @WynApse or @SilverlightNews. Keep it all coming, and... Stay in the 'Light

    Read the article

  • Find the best OpenWorld sessions for learning about UX highlights

    - by mvaughan
    By Kathy Miedema, Oracle Applications User Experience  Have you clicked through the Oracle OpenWorld 2012 catalog? It’s amazingly dense, as usual. But one thing we noticed this year is that nearly half of the sessions mention some component of user experience, which is a sea change in our world. It means that more people understand, appreciate, and desire an effective user experience, and it also means that Oracle’s investment in its next-generation applications user experience, such as Oracle Fusion Applications, is increasingly apparent and interesting to its customers. So how do you choose the user experience sessions that make the most sense for you and your organization? Read our list to find out which sessions we think offer the most value for those interested in finding out more about the Oracle Applications user experience. If you’re interested in Oracle’s strategy for its user experience: CON9438: Oracle Fusion Applications: Transforming Insight into Action10:15 - 11:15 a.m. Tuesday, Oct. 2; Moscone West – 2007 CON9467: Oracle’s Roadmap to a Simple, Modern User Experience3:30 - 4:30 p.m. Wednesday, Oct. 3; Moscone West - 3002/3004 CON8718: Oracle Fusion Applications: Customizing and Extending with Oracle Composers11:15 a.m. - 12:15 p.m. Thursday, Oct. 4; Moscone West – 2008 GEN9663: General Session: A Panel of Masterminds—Where Are Oracle Applications Headed?1:45 - 2:45 p.m. Monday, Oct. 1; Moscone North - Hall D If you’re interested in PeopleSoft/PeopleTools: GEN8928: General Session: PeopleSoft Update and Product Roadmap3:15 - 4:15 p.m. Monday, Oct. 1; Moscone West - 3002/3004 CON9183: PeopleSoft PeopleTools Technology Roadmap4:45 - 5:45 p.m. Monday, Oct. 1; Moscone West - 3002/3004 CON8932: New Functional PeopleSoft PeopleTools Capabilities for the Line-of-Business User5:00 - 6:00 p.m. Tuesday, Oct. 2; Moscone West – 3007 If you’re interested in E-Business Suite: GEN8474: General Session: Oracle E-Business Suite—Strategy, Update, and Roadmap12:15 - 1:15 p.m. Monday, Oct. 1; Moscone West - 2002/2004 CON9026: Latest Oracle E-Business Suite 12.1 User Interface and Usability Enhancements1:15 - 2:15 p.m. Tuesday, Oct. 2; Moscone West – 2016 If you’re interested in Siebel: CON9700: Siebel CRM Overview, Strategy, and Roadmap12:15 - 1:15 p.m. Monday, Oct. 1; Moscone West – 2009 CON9703: User Interface Innovations with the New Siebel “Open UI”10:15 - 11:15 a.m. Tuesday, Oct. 2; Moscone West – 2009 If you’re interested in JD Edwards EnterpriseOne: HOL10452: JD Edwards EnterpriseOne 9.1 User Interface Changes10:15 - 11:15 a.m. Wednesday, Oct. 3; Marriott Marquis - Nob Hill AB CON9160: Showcase of the JD Edwards EnterpriseOne User Experience1:15 - 2:15 p.m. Wednesday, Oct. 3; InterContinental - Grand Ballroom B CON9159: Euphoria with the JD Edwards EnterpriseOne User Experience11:45 a.m. - 12:45 p.m. Wednesday, Oct. 3; InterContinental - Grand Ballroom B If you’re interested in Oracle Fusion Applications user experience design patterns: Functional design patterns that helped create the Oracle Fusion Applications user experience are now available. Learn more about these new, reusable usability solutions and best-practices at the Oracle JDeveloper and Oracle ADF demopods during Oracle OpenWorld 2012. Or visit the OTN Lounge between 4:30 p.m. and 6 p.m. on Wednesday, Oct. 3, to talk to Ultan O'Broin from the Oracle Applications User Experience team.    Demopod location: Moscone Center, South Exhibition Hall Level 1, S-207 OTN (Oracle Technology Network) Lounge: Howard Street tent On the demogrounds: Head to the demogrounds to see new demos from the Applications User Experience team, including the new look for Fusion Applications and what we’re building for mobile platforms. Take a spin on our eye tracker, a very cool tool that we use to research the usability of a particular design. Visit the Usable Apps OpenWorld page to find out where our demopods will be located.Photo by Martin Taylor, Oracle Applications User ExperienceA tour takes place in one of the usability labs at Oracle’s headquarters in Redwood Shores, Calif. At our labs, on-site and at HQ: We are also recruiting participants for our on-site lab, in which we gather feedback on new user experience designs, and taking reservations for a charter bus that will bring you to Oracle headquarters for a lab tour Thursday, Oct. 4, or Friday, Oct. 5. Tours leave at 10 a.m. and 1:45 p.m. from the Moscone Center in San Francisco. You’ll see more of our newest designs at the lab tour, and some of our research tools in action. For more information on any OpenWorld sessions, check the content catalog, also available at www.oracle.com/openworld. For information on Applications User Experience (Apps UX) sessions and activities, go to the Usable Apps OpenWorld page.

    Read the article

  • How to Answer a Stupid Interview Question the Right Way

    - by AjarnMark
    Have you ever been asked a stupid question during an interview; one that seemed to have no relation to the job responsibilities at all?  Tech people are often caught off-guard by these apparently irrelevant questions, but there is a way you can turn these to your favor.  Here is one idea. While chatting with a couple of folks between sessions at SQLSaturday 43 last weekend, one of them expressed frustration over a seemingly ridiculous and trivial question that she was asked during an interview, and she believes it cost her the job opportunity.  The question, as I remember it being described was, “What is the largest byte measurement?”.  The candidate made up a guess (“zetabyte”) during the interview, which is actually closer than she may have realized.  According to Wikipedia, there is a measurement known as zettabyte which is 10^21, and the largest one listed there is yottabyte at 10^24. My first reaction to this question was, “That’s just a hiring manager that doesn’t really know what they’re looking for in a candidate.  Furthermore, this tells me that this manager really does not understand how to build a team.”  In most companies, team interaction is more important than uber-knowledge.  I didn’t ask, but this could also be another geek on the team trying to establish their Alpha-Geek stature.  I suppose that there are a few, very few, companies that can build their businesses on hiring only the extreme alpha-geeks, but that certainly does not represent the majority of businesses in America. My friend who was there suggested that the appropriate response to this silly question would be, “And how does this apply to the work I will be doing?” Of course this is an understandable response when you’re frustrated because you know you can handle the technical aspects of the job, and it seems like the interviewer is just being silly.  But it is also a direct challenge, which may not be the best approach in interviewing.  I do have to admit, though, that there are those folks who just won’t respect you until you do challenge them, but again, I don’t think that is the majority. So after some thought, here is my suggestion: “Well, I know that there are petabytes and exabytes and things even larger than that, but I haven’t been keeping up on my list of Greek prefixes that have not yet been used, so I would have to look up the exact answer if you need it.  However, I have worked with databases as large as 30 Terabytes.  How big are the largest databases here at X Corporation?”  Perhaps with a follow-up of, “Typically, what I have seen in companies that have databases of your size, is that the three biggest challenges they face are: A, B, and C.  What would you say are the top 3 concerns that you would like the person you hire to be able to address?…Here is how I have dealt with those concerns in the past (or ‘Here is how I would tackle those issues for you…’).” Wait! What just happened?!  We took a seemingly irrelevant and frustrating question and turned it around into an opportunity to highlight our relevant skills and guide the conversation back in a direction more to our liking and benefit.  In more generic terms, here is what we did: Admit that you don’t know the specific answer off the top of your head, but can get it if it’s truly important to the company. Maybe for some reason it really is important to them. Mention something similar or related that you do know, reassuring them that you do have some knowledge in that subject area. Draw a parallel to your past work experience. Ask follow-up questions about the company’s specific needs and discuss how you can fulfill those. This type of thing requires practice and some forethought.  I didn’t come up with this answer until a day later, which is too late when you’re interviewing.  I still think it is silly for an interviewer to ask something like that, but at least this is one way to spin it to your advantage while you consider whether you really want to work for someone who would ask a thing like that.  Remember, interviewing is a two-way process.  You’re deciding whether you want to work there just as much as they are deciding whether they want you. There is always the possibility that this was a calculated maneuver on the part of the hiring manager just to see how quickly you think on your feet and how you handle stupid questions.  Maybe he knows something about the work environment and he’s trying to gauge whether you’ll actually fit in okay.  And if that’s the case, then the above response still works quite well.

    Read the article

  • NoSQL Java API for MySQL Cluster: Questions & Answers

    - by Mat Keep
    The MySQL Cluster engineering team recently ran a live webinar, available now on-demand demonstrating the ClusterJ and ClusterJPA NoSQL APIs for MySQL Cluster, and how these can be used in building real-time, high scale Java-based services that require continuous availability. Attendees asked a number of great questions during the webinar, and I thought it would be useful to share those here, so others are also able to learn more about the Java NoSQL APIs. First, a little bit about why we developed these APIs and why they are interesting to Java developers. ClusterJ and Cluster JPA ClusterJ is a Java interface to MySQL Cluster that provides either a static or dynamic domain object model, similar to the data model used by JDO, JPA, and Hibernate. A simple API gives users extremely high performance for common operations: insert, delete, update, and query. ClusterJPA works with ClusterJ to extend functionality, including - Persistent classes - Relationships - Joins in queries - Lazy loading - Table and index creation from object model By eliminating data transformations via SQL, users get lower data access latency and higher throughput. In addition, Java developers have a more natural programming method to directly manage their data, with a complete, feature-rich solution for Object/Relational Mapping. As a result, the development of Java applications is simplified with faster development cycles resulting in accelerated time to market for new services. MySQL Cluster offers multiple NoSQL APIs alongside Java: - Memcached for a persistent, high performance, write-scalable Key/Value store, - HTTP/REST via an Apache module - C++ via the NDB API for the lowest absolute latency. Developers can use SQL as well as NoSQL APIs for access to the same data set via multiple query patterns – from simple Primary Key lookups or inserts to complex cross-shard JOINs using Adaptive Query Localization Marrying NoSQL and SQL access to an ACID-compliant database offers developers a number of benefits. MySQL Cluster’s distributed, shared-nothing architecture with auto-sharding and real time performance makes it a great fit for workloads requiring high volume OLTP. Users also get the added flexibility of being able to run real-time analytics across the same OLTP data set for real-time business insight. OK – hopefully you now have a better idea of why ClusterJ and JPA are available. Now, for the Q&A. Q & A Q. Why would I use Connector/J vs. ClusterJ? A. Partly it's a question of whether you prefer to work with SQL (Connector/J) or objects (ClusterJ). Performance of ClusterJ will be better as there is no need to pass through the MySQL Server. A ClusterJ operation can only act on a single table (e.g. no joins) - ClusterJPA extends that capability Q. Can I mix different APIs (ie ClusterJ, Connector/J) in our application for different query types? A. Yes. You can mix and match all of the API types, SQL, JDBC, ODBC, ClusterJ, Memcached, REST, C++. They all access the exact same data in the data nodes. Update through one API and new data is instantly visible to all of the others. Q. How many TCP connections would a SessionFactory instance create for a cluster of 8 data nodes? A. SessionFactory has a connection to the mgmd (management node) but otherwise is just a vehicle to create Sessions. Without using connection pooling, a SessionFactory will have one connection open with each data node. Using optional connection pooling allows multiple connections from the SessionFactory to increase throughput. Q. Can you give details of how Cluster J optimizes sharding to enhance performance of distributed query processing? A. Each data node in a cluster runs a Transaction Coordinator (TC), which begins and ends the transaction, but also serves as a resource to operate on the result rows. While an API node (such as a ClusterJ process) can send queries to any TC/data node, there are performance gains if the TC is where most of the result data is stored. ClusterJ computes the shard (partition) key to choose the data node where the row resides as the TC. Q. What happens if we perform two primary key lookups within the same transaction? Are they sent to the data node in one transaction? A. ClusterJ will send identical PK lookups to the same data node. Q. How is distributed query processing handled by MySQL Cluster ? A. If the data is split between data nodes then all of the information will be transparently combined and passed back to the application. The session will connect to a data node - typically by hashing the primary key - which then interacts with its neighboring nodes to collect the data needed to fulfil the query. Q. Can I use Foreign Keys with MySQL Cluster A. Support for Foreign Keys is included in the MySQL Cluster 7.3 Early Access release Summary The NoSQL Java APIs are packaged with MySQL Cluster, available for download here so feel free to take them for a spin today! Key Resources MySQL Cluster on-line demo  MySQL ClusterJ and JPA On-demand webinar  MySQL ClusterJ and JPA documentation MySQL ClusterJ and JPA whitepaper and tutorial

    Read the article

  • problems with my slotgame [delphi]

    - by Raiden2k
    hey guys im coding at the moment on a slotgame for the learning effect. here is the source code. my questions are below: unit Unit1; {$mode objfpc}{$H+} interface uses Classes, SysUtils, Windows, FileUtil, Forms, Controls, Graphics, Dialogs, StdCtrls, ExtCtrls, ComCtrls, Menus, ActnList, Spin, FileCtrl; type { TForm1 } TForm1 = class(TForm) FloatSpinEdit1: TFloatSpinEdit; Guthabenlb: TLabel; s4: TLabel; s5: TLabel; s6: TLabel; s7: TLabel; s8: TLabel; s9: TLabel; Timer3: TTimer; Winlb: TLabel; Loselb: TLabel; slotbn: TButton; s1: TLabel; s2: TLabel; s3: TLabel; Timer1: TTimer; Timer2: TTimer; procedure FormCreate(Sender: TObject); procedure slotbnClick(Sender: TObject); procedure Timer1Timer(Sender: TObject); procedure Timer2Timer(Sender: TObject); procedure Timer3Timer(Sender: TObject); private { private declarations } FRollen : array [0..2, 0..9] of String; public { public declarations } end; var Form1: TForm1; wins,loses : Integer; guthaben : Double = 10; implementation {$R *.lfm} { TForm1 } procedure TForm1.slotbnClick(Sender: TObject); begin Guthaben := Guthaben - 1.00; Guthabenlb.Caption := FloatToStr(guthaben) + (' €'); Timer1.Enabled := True; Timer2.Enabled := True; slotbn.Enabled := false; end; procedure TForm1.FormCreate(Sender: TObject); var i: integer; j: integer; n: integer; digits: TStringlist; begin Digits := TStringList.Create; try for i := low(FRollen) to high(FRollen) do begin for j := low(FRollen[i]) to high(FRollen[i]) do Digits.Add(IntToStr(j)); for j := low(FRollen[i]) to high(FRollen[i]) do begin n := Random(Digits.Count); FRollen[i, j] := Digits[n]; Digits.Delete(n); end; end finally Digits.Free; end; for i:=low(FRollen) to high(FRollen) do begin end; end; //==================================================================================================\\ // Drehen der Slots im Zufallsmodus //==================================================================================================// procedure TForm1.Timer1Timer(Sender: TObject); begin s1.Caption := IntToStr(Random(9)); s2.Caption := IntToStr(Random(9)); s3.Caption := IntToStr(Random(9)); s4.Caption := IntToStr(Random(9)); s5.Caption := IntToStr(Random(9)); s6.Caption := IntToStr(Random(9)); s7.Caption := IntToStr(Random(9)); s8.Caption := IntToStr(Random(9)); s9.Caption := IntToStr(Random(9)); end; //==================================================================================================// //===================================================================================================\\ // Gewonnen / Verloren abfrage //===================================================================================================// procedure TForm1.Timer2Timer(Sender: TObject); begin Timer1.Enabled := False; Timer2.Enabled := false; if (s1.Caption = s5.Caption) and (s1.Caption = s9.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else if (s1.Caption = s4.Caption) and (s1.Caption = s7.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else if (s2.Caption = s5.Caption) and (s2.Caption = s8.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else if (s3.Caption = s6.Caption) and (s3.Caption = s9.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else if (s3.Caption = s5.Caption) and (s3.Caption = s7.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else Inc(loses); slotbn.Enabled := True; Loselb.Caption := 'Loses: ' + IntToStr(loses); Winlb.Caption := 'Wins: ' + IntTostr(Wins); end; procedure TForm1.Timer3Timer(Sender: TObject); begin if (guthaben = 0) or (guthaben < 0) then begin Timer3.Enabled := False; MessageBox(handle,'Du hast verloren!','Verlierer!',MB_OK); close(); end; end; //======================================================================================================\\ end. How can i replace the labels through icons 16 x 16 pixels? How can i adjust the winning sum according to the icons.(for example 3 crowns give you 40 € and 3 apples only 10 €) How can i adhust the winning sum with a sum for every round?

    Read the article

  • .NET development on a Retina MacBook Pro with Windows 8

    - by Jeff
    I remember sitting in Building 5 at Microsoft with some of my coworkers, when one of them came in with a shiny new 11” MacBook Air. It was nearly two years ago, and we found it pretty odd that the OEM’s building Windows machines sucked at industrial design in a way that defied logic. While Dell and HP were in a race to the bottom building commodity crap, Apple was staying out of the low-end market completely, and focusing on better design. In the process, they managed to build machines people actually wanted, and maintain an insanely high margin in the process. I stopped buying the commodity crap and custom builds in 2006, when Apple went Intel. As a .NET guy, I was still in it for Microsoft’s stack of development tools, which I found awesome, but had back to back crappy laptops from HP and Dell. After that original 15” MacBook Pro, I also had a Mac Pro tower (that I sold after three years for $1,500!), a 27” iMac, and my favorite, a 17” MacBook Pro (the unibody style) with an SSD added from OWC. The 17” was a little much to carry around because it was heavy, but it sure was nice getting as much as eight hours of battery life, and the screen was amazing. When the rumors started about a 15” model with a “retina” screen inspired by the Air, I made up my mind I wanted one, and ordered it the day it came out. I sold my 17”, after three years, for $750 to a friend who is really enjoying it. I got the base model with the upgrade to 16 gigs of RAM. It feels solid for being so thin, and if you’ve used the third generation iPad or the newer iPhone, you’ll be just as thrilled with the screen resolution. I’m typically getting just over six hours of battery life while running a VM, but Parallels 8 allegedly makes some power improvements, so we’ll see what happens. (It was just released today.) The nice thing about VM’s are that you can run more than one at a time. Primarily I run the Windows 8 VM with four cores (the laptop is quad-core, but has 8 logical cores due to hyperthreading or whatever Intel calls it) and 8 gigs of RAM. I also have a Windows Server 2008 R2 VM I spin up when I need to test stuff in a “real” server environment, and I give it two cores and 4 gigs of RAM. The Windows 8 VM spins up in about 8 seconds. Visual Studio 2012 takes a few more seconds, but count part of that as the “ReSharper tax” as it does its startup magic. The real beauty, the thing I looked most forward to, is that beautifully crisp C# text. Consolas has never looked as good as it does at 10pt. as it does on this display. You know how it looks great at 80pt. when conference speakers demo stuff on a projector? Think that sharpness, only tiny. It’s just gorgeous. Beyond that, everything is just so responsive and fast. Builds of large projects happen in seconds, hundreds of unit tests run in seconds… you just don’t spend a lot of time waiting for stuff. It’s kind of painful to go back to my 27” iMac (which would be better if I put an SSD in it before its third birthday). Are there negatives? A few minor issues, yes. As is the case with OS X, not everything scales right. You’ll see some weirdness at times with splash screens and icons and such. Chrome’s text rendering (in Windows) is apparently not aware of how to deal with higher DPI’s, so text is fuzzy (the OS X version is super sharp, however). You’ll also have to do some fiddling with keyboard settings to use the Windows 8 keyboard shortcuts. Overall, it’s as close to a no-compromise development experience as I’ve ever had. I’m not even going to bother with Boot Camp because the VM route already exceeds my expectations. You definitely get what you pay for. If this one also lasts three years and I can turn around and sell it, it’s worth it for something I use every day.

    Read the article

  • Session Report - Java on the Raspberry Pi

    - by Janice J. Heiss
    On mid-day Wednesday, the always colorful Oracle Evangelist Simon Ritter demonstrated Java on the Raspberry Pi at his session, “Do You Like Coffee with Your Dessert?”. The Raspberry Pi consists of a credit card-sized single-board computer developed in the UK with the intention of stimulating the teaching of basic computer science in schools. “I don't think there is a single feature that makes the Raspberry Pi significant,” observed Ritter, “but a combination of things really makes it stand out. First, it's $35 for what is effectively a completely usable computer. You do have to add a power supply, SD card for storage and maybe a screen, keyboard and mouse, but this is still way cheaper than a typical PC. The choice of an ARM (Advanced RISC Machine and Acorn RISC Machine) processor is noteworthy, because it avoids problems like cooling (no heat sink or fan) and can use a USB power brick. When you add in the enormous community support, it offers a great platform for teaching everyone about computing.”Some 200 enthusiastic attendees were present at the session which had the feel of Simon Ritter sharing a fun toy with friends. The main point of the session was to show what Oracle was doing to support Java on the Raspberry Pi in a way that is entertaining and fun. Ritter pointed out that, in addition to being great for teaching, it’s an excellent introduction to the ARM architecture, and runs well with Java and will get better once it has official hard float support. The possibilities are vast.Ritter explained that the Raspberry Pi Project started in 2006 with the goal of devising a computer to inspire children; it drew inspiration from the BBC Micro literacy project of 1981 that produced a series of microcomputers created by the Acorn Computer company. It was officially launched on February 29, 2012, with a first production of 10,000 boards. There were 100,000 pre-orders in one day; currently about 4,000 boards are produced a day. Ritter described the specification as follows:* CPU: ARM 11 core running at 700MHz Broadcom SoC package Can now be overclocked to 1GHz (without breaking the warranty!) * Memory: 256Mb* I/O: HDMI and composite video 2 x USB ports (Model B only) Ethernet (Model B only) Header pins for GPIO, UART, SPI and I2C He took attendees through a brief history of ARM Architecture:* Acorn BBC Micro (6502 based) Not powerful enough for Acorn’s plans for a business computer * Berkeley RISC Project UNIX kernel only used 30% of instruction set of Motorola 68000 More registers, less instructions (Register windows) One chip architecture to come from this was… SPARC * Acorn RISC Machine (ARM) 32-bit data, 26-bit address space, 27 registers First machine was Acorn Archimedes * Spin off from Acorn, Advanced RISC MachinesNext he presented its features:* 32-bit RISC Architecture–  ARM accounts for 75% of embedded 32-bit CPUs today– 6.1 Billion chips sold last year (zero manufactured by ARM)* Abstract architecture and microprocessor core designs– Raspberry Pi is ARM11 using ARMv6 instruction set* Low power consumption– Good for mobile devices– Raspberry Pi can be powered from 700mA 5V only PSU– Raspberry Pi does not require heatsink or fanHe described the current ARM Technology:* ARMv6– ARM 11, ARM Cortex-M* ARMv7– ARM Cortex-A, ARM Cortex-M, ARM Cortex-R* ARMv8 (Announced)– Will support 64-bit data and addressingHe next gave the Java Specifics for ARM: Floating point operations* Despite being an ARMv6 processor it does include an FPU– FPU only became standard as of ARMv7* FPU (Hard Float, or HF) is much faster than a software library* Linux distros and Oracle JVM for ARM assume no HF on ARMv6– Need special build of both– Raspbian distro build now available– Oracle JVM is in the works, release date TBDNot So RISCPerformance Improvements* DSP Enhancements* Jazelle* Thumb / Thumb2 / ThumbEE* Floating Point (VFP)* NEON* Security Enhancements (TrustZone)He spent a few minutes going over the challenges of using Java on the Raspberry Pi and covered:* Sound* Vision * Serial (TTL UART)* USB* GPIOTo implement sound with Java he pointed out:* Sound drivers are now included in new distros* Java Sound API– Remember to add audio to user’s groups– Some bits work, others not so much* Playing (the right format) WAV file works* Using MIDI hangs trying to open a synthesizer* FreeTTS text-to-speech– Should work once sound works properlyHe turned to JavaFX on the Raspberry Pi:* Currently internal builds only– Will be released as technology preview soon* Work involves optimal implementation of Prism graphics engine– X11?* Once the JavaFX implementation is completed there will be little of concern to developers-- It’s just Java (WORA). He explained the basis of the Serial Port:* UART provides TTL level signals (3.3V)* RS-232 uses 12V signals* Use MAX3232 chip to convert* Use this for access to serial consoleHe summarized his key points. The Raspberry Pi is a very cool (and cheap) computer that is great for teaching, a great introduction to ARM that works very well with Java and will work better in the future. The opportunities are limitless. For further info, check out, Raspberry Pi User Guide by Eben Upton and Gareth Halfacree. From there, Ritter tried out several fun demos, some of which worked better than others, but all of which were greeted with considerable enthusiasm and support and good humor (even when he ran into some glitches).  All in all, this was a fun and lively session.

    Read the article

  • Problems with my slotgame

    - by Raiden2k
    I'm coding a slot game for learning. Here's the source code. My questions are below. unit Unit1; {$mode objfpc}{$H+} interface uses Classes, SysUtils, Windows, FileUtil, Forms, Controls, Graphics, Dialogs, StdCtrls, ExtCtrls, ComCtrls, Menus, ActnList, Spin, FileCtrl; type { TForm1 } TForm1 = class(TForm) FloatSpinEdit1: TFloatSpinEdit; Guthabenlb: TLabel; s4: TLabel; s5: TLabel; s6: TLabel; s7: TLabel; s8: TLabel; s9: TLabel; Timer3: TTimer; Winlb: TLabel; Loselb: TLabel; slotbn: TButton; s1: TLabel; s2: TLabel; s3: TLabel; Timer1: TTimer; Timer2: TTimer; procedure FormCreate(Sender: TObject); procedure slotbnClick(Sender: TObject); procedure Timer1Timer(Sender: TObject); procedure Timer2Timer(Sender: TObject); procedure Timer3Timer(Sender: TObject); private { private declarations } FRollen : array [0..2, 0..9] of String; public { public declarations } end; var Form1: TForm1; wins,loses : Integer; guthaben : Double = 10; implementation {$R *.lfm} { TForm1 } procedure TForm1.slotbnClick(Sender: TObject); begin Guthaben := Guthaben - 1.00; Guthabenlb.Caption := FloatToStr(guthaben) + (' €'); Timer1.Enabled := True; Timer2.Enabled := True; slotbn.Enabled := false; end; procedure TForm1.FormCreate(Sender: TObject); var i: integer; j: integer; n: integer; digits: TStringlist; begin Digits := TStringList.Create; try for i := low(FRollen) to high(FRollen) do begin for j := low(FRollen[i]) to high(FRollen[i]) do Digits.Add(IntToStr(j)); for j := low(FRollen[i]) to high(FRollen[i]) do begin n := Random(Digits.Count); FRollen[i, j] := Digits[n]; Digits.Delete(n); end; end finally Digits.Free; end; for i:=low(FRollen) to high(FRollen) do begin end; end; //==================================================================================================\\ // Drehen der Slots im Zufallsmodus //==================================================================================================// procedure TForm1.Timer1Timer(Sender: TObject); begin s1.Caption := IntToStr(Random(9)); s2.Caption := IntToStr(Random(9)); s3.Caption := IntToStr(Random(9)); s4.Caption := IntToStr(Random(9)); s5.Caption := IntToStr(Random(9)); s6.Caption := IntToStr(Random(9)); s7.Caption := IntToStr(Random(9)); s8.Caption := IntToStr(Random(9)); s9.Caption := IntToStr(Random(9)); end; //==================================================================================================// //===================================================================================================\\ // Gewonnen / Verloren abfrage //===================================================================================================// procedure TForm1.Timer2Timer(Sender: TObject); begin Timer1.Enabled := False; Timer2.Enabled := false; if (s1.Caption = s5.Caption) and (s1.Caption = s9.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else if (s1.Caption = s4.Caption) and (s1.Caption = s7.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else if (s2.Caption = s5.Caption) and (s2.Caption = s8.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else if (s3.Caption = s6.Caption) and (s3.Caption = s9.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else if (s3.Caption = s5.Caption) and (s3.Caption = s7.Caption) then begin Guthaben := Guthaben + 5.00; Inc(wins); end else Inc(loses); slotbn.Enabled := True; Loselb.Caption := 'Loses: ' + IntToStr(loses); Winlb.Caption := 'Wins: ' + IntTostr(Wins); end; procedure TForm1.Timer3Timer(Sender: TObject); begin if (guthaben = 0) or (guthaben < 0) then begin Timer3.Enabled := False; MessageBox(handle,'Du hast verloren!','Verlierer!',MB_OK); close(); end; end; //======================================================================================================\\ end. How can I replace the labels through icons 16 x 16 pixels? How can I adjust the winning sum according to the icons? (for example 3 crowns give you 40 € and 3 apples only 10 €) How can I adjust the winning sum with a sum for every round?

    Read the article

  • NetBeans, JSF, and MySQL Primary Keys using AUTO_INCREMENT

    - by MarkH
    I recently had the opportunity to spin up a small web application using JSF and MySQL. Having developed JSF apps with Oracle Database back-ends before and possessing some small familiarity with MySQL (sans JSF), I thought this would be a cakewalk. Things did go pretty smoothly...but there was one little "gotcha" that took more time than the few seconds it really warranted. The Problem Every DBMS has its own way of automatically generating primary keys, and each has its pros and cons. For the Oracle Database, you use a sequence and point your Java classes to it using annotations that look something like this: @GeneratedValue(strategy=GenerationType.SEQUENCE, generator="POC_ID_SEQ") @SequenceGenerator(name="POC_ID_SEQ", sequenceName="POC_ID_SEQ", allocationSize=1) Between creating the actual sequence in the database and making sure you have your annotations right (watch those typos!), it seems a bit cumbersome. But it typically "just works", without fuss. Enter MySQL. Designating an integer-based field as PRIMARY KEY and using the keyword AUTO_INCREMENT makes the same task seem much simpler. And it is, mostly. But while NetBeans cranks out a superb "first cut" for a basic JSF CRUD app, there are a couple of small things you'll need to bring to the mix in order to be able to actually (C)reate records. The (RUD) performs fine out of the gate. The Solution Omitting all design considerations and activity (!), here is the basic sequence of events I followed to create, then resolve, the JSF/MySQL "Primary Key Perfect Storm": Fire up NetBeans. Create JSF project. Create Entity Classes from Database. Create JSF Pages from Entity Classes. Test run. Try to create record and hit error. It's a simple fix, but one that was fun to find in its completeness. :-) Even though you've told it what to do for a primary key, a MySQL table requires a gentle nudge to actually generate that new key value. Two things are needed to make the magic happen. First, you need to ensure the following annotation is in place in your Java entity classes: @GeneratedValue(strategy = GenerationType.IDENTITY) All well and good, but the real key is this: in your controller class(es), you'll have a create() function that looks something like this, minus the comment line and the setId() call in bold red type:     public String create() {         try {             // Assign 0 to ID for MySQL to properly auto_increment the primary key.             current.setId(0);             getFacade().create(current);             JsfUtil.addSuccessMessage(ResourceBundle.getBundle("/Bundle").getString("CategoryCreated"));             return prepareCreate();         } catch (Exception e) {             JsfUtil.addErrorMessage(e, ResourceBundle.getBundle("/Bundle").getString("PersistenceErrorOccured"));             return null;         }     } Setting the current object's primary key attribute to zero (0) prior to saving it tells MySQL to get the next available value and assign it to that record's key field. Short and simple…but not inherently obvious if you've never used that particular combination of NetBeans/JSF/MySQL before. Hope this helps! All the best, Mark

    Read the article

  • Relative cam movement and momentum on arbitrary surface

    - by user29244
    I have been working on a game for quite long, think sonic classic physics in 3D or tony hawk psx, with unity3D. However I'm stuck at the most fundamental aspect of movement. The requirement is that I need to move the character in mario 64 fashion (or sonic adventure) aka relative cam input: the camera's forward direction always point input forward the screen, left or right input point toward left or right of the screen. when input are resting, the camera direction is independent from the character direction and the camera can orbit the character when input are pressed the character rotate itself until his direction align with the direction the input is pointing at. It's super easy to do as long your movement are parallel to the global horizontal (or any world axis). However when you try to do this on arbitrary surface (think moving along complex curved surface) with the character sticking to the surface normal (basically moving on wall and ceiling freely), it seems harder. What I want is to achieve the same finesse of movement than in mario but on arbitrary angled surfaces. There is more problem (jumping and transitioning back to the real world alignment and then back on a surface while keeping momentum) but so far I didn't even take off the basics. So far I have accomplish moving along the curved surface and the relative cam input, but for some reason direction fail all the time (point number 3, the character align slowly to the input direction). Do you have an idea how to achieve that? Here is the code and some demo so far: The demo: https://dl.dropbox.com/u/24530447/flash%20build/litesonicengine/LiteSonicEngine5.html Camera code: using UnityEngine; using System.Collections; public class CameraDrive : MonoBehaviour { public GameObject targetObject; public Transform camPivot, camTarget, camRoot, relcamdirDebug; float rot = 0; //---------------------------------------------------------------------------------------------------------- void Start() { this.transform.position = targetObject.transform.position; this.transform.rotation = targetObject.transform.rotation; } void FixedUpdate() { //the pivot system camRoot.position = targetObject.transform.position; //input on pivot orientation rot = 0; float mouse_x = Input.GetAxisRaw( "camera_analog_X" ); // rot = rot + ( 0.1f * Time.deltaTime * mouse_x ); // wrapAngle( rot ); // //when the target object rotate, it rotate too, this should not happen UpdateOrientation(this.transform.forward,targetObject.transform.up); camRoot.transform.RotateAround(camRoot.transform.up,rot); //debug the relcam dir RelativeCamDirection() ; //this camera this.transform.position = camPivot.position; //set the camera to the pivot this.transform.LookAt( camTarget.position ); // } //---------------------------------------------------------------------------------------------------------- public float wrapAngle ( float Degree ) { while (Degree < 0.0f) { Degree = Degree + 360.0f; } while (Degree >= 360.0f) { Degree = Degree - 360.0f; } return Degree; } private void UpdateOrientation( Vector3 forward_vector, Vector3 ground_normal ) { Vector3 projected_forward_to_normal_surface = forward_vector - ( Vector3.Dot( forward_vector, ground_normal ) ) * ground_normal; camRoot.transform.rotation = Quaternion.LookRotation( projected_forward_to_normal_surface, ground_normal ); } float GetOffsetAngle( float targetAngle, float DestAngle ) { return ((targetAngle - DestAngle + 180)% 360) - 180; } //---------------------------------------------------------------------------------------------------------- void OnDrawGizmos() { Gizmos.DrawCube( camPivot.transform.position, new Vector3(1,1,1) ); Gizmos.DrawCube( camTarget.transform.position, new Vector3(1,5,1) ); Gizmos.DrawCube( camRoot.transform.position, new Vector3(1,1,1) ); } void OnGUI() { GUI.Label(new Rect(0,80,1000,20*10), "targetObject.transform.up : " + targetObject.transform.up.ToString()); GUI.Label(new Rect(0,100,1000,20*10), "target euler : " + targetObject.transform.eulerAngles.y.ToString()); GUI.Label(new Rect(0,100,1000,20*10), "rot : " + rot.ToString()); } //---------------------------------------------------------------------------------------------------------- void RelativeCamDirection() { float input_vertical_movement = Input.GetAxisRaw( "Vertical" ), input_horizontal_movement = Input.GetAxisRaw( "Horizontal" ); Vector3 relative_forward = Vector3.forward, relative_right = Vector3.right, relative_direction = ( relative_forward * input_vertical_movement ) + ( relative_right * input_horizontal_movement ) ; MovementController MC = targetObject.GetComponent<MovementController>(); MC.motion = relative_direction.normalized * MC.acceleration * Time.fixedDeltaTime; MC.motion = this.transform.TransformDirection( MC.motion ); //MC.transform.Rotate(Vector3.up, input_horizontal_movement * 10f * Time.fixedDeltaTime); } } Mouvement code: using UnityEngine; using System.Collections; public class MovementController : MonoBehaviour { public float deadZoneValue = 0.1f, angle, acceleration = 50.0f; public Vector3 motion ; //-------------------------------------------------------------------------------------------- void OnGUI() { GUILayout.Label( "transform.rotation : " + transform.rotation ); GUILayout.Label( "transform.position : " + transform.position ); GUILayout.Label( "angle : " + angle ); } void FixedUpdate () { Ray ground_check_ray = new Ray( gameObject.transform.position, -gameObject.transform.up ); RaycastHit raycast_result; Rigidbody rigid_body = gameObject.rigidbody; if ( Physics.Raycast( ground_check_ray, out raycast_result ) ) { Vector3 next_position; //UpdateOrientation( gameObject.transform.forward, raycast_result.normal ); UpdateOrientation( gameObject.transform.forward, raycast_result.normal ); next_position = GetNextPosition( raycast_result.point ); rigid_body.MovePosition( next_position ); } } //-------------------------------------------------------------------------------------------- private void UpdateOrientation( Vector3 forward_vector, Vector3 ground_normal ) { Vector3 projected_forward_to_normal_surface = forward_vector - ( Vector3.Dot( forward_vector, ground_normal ) ) * ground_normal; transform.rotation = Quaternion.LookRotation( projected_forward_to_normal_surface, ground_normal ); } private Vector3 GetNextPosition( Vector3 current_ground_position ) { Vector3 next_position; // //-------------------------------------------------------------------- // angle = 0; // Vector3 dir = this.transform.InverseTransformDirection(motion); // angle = Vector3.Angle(Vector3.forward, dir);// * 1f * Time.fixedDeltaTime; // // if(angle > 0) this.transform.Rotate(0,angle,0); // //-------------------------------------------------------------------- next_position = current_ground_position + gameObject.transform.up * 0.5f + motion ; return next_position; } } Some observation: I have the correct input, I have the correct translation in the camera direction ... but whenever I attempt to slowly lerp the direction of the character in direction of the input, all I get is wild spin! Sad Also discovered that strafing to the right (immediately at the beginning without moving forward) has major singularity trapping on the equator!! I'm totally lost and crush (I have already done a much more featured version which fail at the same aspect)

    Read the article

  • The application called an interface that was marshalled for a different thread

    - by X-Ray
    i'm writing a delphi app that communicates with excel. one thing i noticed is that if i call the Save method on the Excel workbook object, it can appear to hang because excel has a dialog box open for the user. i'm using the late binding. i'd like for my app to be able to notice when Save takes several seconds and then take some kind of action like show a dialog box telling this is what's happening. i figured this'd be fairly easy. all i'd need to do is create a thread that calls Save and have that thread call Excel's Save routine. if it takes too long, i can take some action. procedure TOfficeConnect.Save; var Thread:TOfficeHangThread; begin // spin off as thread so we can control timeout Thread:=TOfficeSaveThread.Create(m_vExcelWorkbook); if WaitForSingleObject(Thread.Handle, 5 {s} * 1000 {ms/s})=WAIT_TIMEOUT then begin Thread.FreeOnTerminate:=true; raise Exception.Create(_('The Office spreadsheet program seems to be busy.')); end; Thread.Free; end; TOfficeSaveThread = class(TThread) private { Private declarations } m_vExcelWorkbook:variant; protected procedure Execute; override; procedure DoSave; public constructor Create(vExcelWorkbook:variant); end; { TOfficeSaveThread } constructor TOfficeSaveThread.Create(vExcelWorkbook:variant); begin inherited Create(true); m_vExcelWorkbook:=vExcelWorkbook; Resume; end; procedure TOfficeSaveThread.Execute; begin m_vExcelWorkbook.Save; end; i understand this problem happens because the OLE object was created from another thread (absolutely). how can i get around this problem? most likely i'll need to "re-marshall" for this call somehow... any ideas? thank you!

    Read the article

  • MVC 2 View Layout CSS Control Layout

    - by Cory Mathewson
    I'm new to a lot of what I'm trying to do with the development of a new MVC2 web application so this is a beginner question. I need to understand my options for control and content layout on a web page. I’m using MVC2 so I’m using Controllers, Views, ViewModels, and View Templates. What I need to spin up on…fast…is control the granular layout of controls and content on any particular view. Below I’ve pasted two examples of auto generated templates that illustrate my challenge. I see that layout is controlled by CSS in my Site.css document. In the first example I get a sequential flow of DisplayLabel and DisplayField. I prefer the adjacent layout of DisplayLabel on the same line as DisplayField produced from example 2. However, example 2 is too simple because the formatting is applied to the Label and the Field. I think the correct way to tackle this learning curve is Microsoft Expression but I don’t have personal bandwidth at the moment to tackle Expression. Can anyone point me to a resource that will expose me to lots of examples for CSS formatting? I have lots of syntax questions. For instance, I believe is referencing the Site.css but I can’t find a "display-label" section in Site.css. Example 1 <fieldset> <legend>Fields</legend> <div class="display-label">DocTitle</div> <div class="display-field"><%: Model.DocTitle %></div> <div class="display-label">DocoumentPropertiesID</div> <div class="display-field"><%: Model.DocumentPropertiesID %></div> Example 2 <h2>Title: <%: Model.DocTitle %></h2> <h2>Created: <%: Model.Created %></h2> <h2>Modified: <%: Model.Modified %></h2> <h2>Author: <%: Model.tbl_Author.Name %></h2> <h2>Genre: <%: Model.tbl_DocumentGenre.GenreName %></h2>

    Read the article

  • Using 32bit COM object from C# or VBS on Vista 64bit and getting error 80004005

    - by alexandroid
    I need some mind reading here, since I am trying to do what I do not completely understand. There is a 32-bit application (electronic trading application called CQG) which provides a COM API for external access. I have sample programs and scripts which access this API from Excel, .NET (C++, VB and C#) and shell VBScript. I have these .NET applications as source code and as compiled executables (32-bit, compiled on Windows XP). Now I have Windows Vista Home 64-bit which makes my head to spin. Excel examples work just fine (in Excel 2003). Compiled .NET sample executables work as well. But when I am trying to run .NET C# sample converted to and compiled by Visual Studio C# Expression, or run the VBScript script, I am getting error 80004005 when trying to create an object. Initially the .NET application also gave me 80040154 but then I figured how to make it produce 32-bit code and not 64-bit, so now the errors in C# and VBScript applications are the same. That's all the progress I got for now. And yes, I tried running 32-bit versions of cscript.exe/WScript from SysWOW64 folder on my VBS, but still the result is the same (80004005). How to solve this problem? I am almost ready to believe it is practically impossible, but the fact that Excel VBA works and .NET executables compiled on Windows XP run just fine just makes me angry. There should be a way to beat this thing (some secret which probably only Windows Vista developers know)! I will appreciate any help! PS: I believe code samples do not make much sense here, but this is the line of VBScript which fails: Set CEL = WScript.CreateObject("CQG.CQGCEL.4.0", "CEL_") And this is C#: CQGCEL CEL = new CQGCEL(); Update: Forgot to say UAC is off, of course. And I am working from account with administrator priviledges. I also tried watching which registry keys are read using Process Monitor but everything looks OK for GUIDs of this object. I could not recognize some other GUIDs so I am not sure whether they were critical or not. Is there a chance that this COM object uses Internet Explorer and gets the wrong one (like Internet Explorer 7 instead of Internet Explorer 6 engine or something)?

    Read the article

  • Stumbleupon type query...

    - by Chris Denman
    Wow, makes your head spin! I am about to start a project, and although my mySql is OK, I can't get my head around what required for this: I have a table of web addresses. id,url 1,http://www.url1.com 2,http://www.url2.com 3,http://www.url3.com 4,http://www.url4.com I have a table of users. id,name 1,fred bloggs 2,john bloggs 3,amy bloggs I have a table of categories. id,name 1,science 2,tech 3,adult 4,stackoverflow I have a table of categories the user likes as numerical ref relating to the category unique ref. For example: user,category 1,4 1,6 1,7 1,10 2,3 2,4 3,5 . . . I have a table of scores relating to each website address. When a user visits one of these sites and says they like it, it's stored like so: url_ref,category 4,2 4,3 4,6 4,2 4,3 5,2 5,3 . . . So based on the above data, URL 4 would score (in it's own right) as follows: 2=2 3=2 6=1 What I was hoping to do was pick out a random URL from over 2,000,000 records based on the current users interests. So if the logged in user likes categories 1,2,3 then I would like to ORDER BY a score generated based on their interest. If the logged in user likes categories 2 3 and 6 then the total score would be 5. However, if the current logged in user only like categories 2 and 6, the URL score would be 3. So the order by would be in context of the logged in users interests. Think of stumbleupon. I was thinking of using a set of VIEWS to help with sub queries. I'm guessing that all 2,000,000 records will need to be looked at and based on the id of the url it will look to see what scores it has based on each selected category of the current user. So we need to know the user ID and this gets passed into the query as a constant from the start. Ain't got a clue! Chris Denman

    Read the article

  • Why does Python's math.factorial not play nice with threads?

    - by W1N9Zr0
    Why does math.factorial act so weird in a thread? Here is an example, it creates three threads: thread that just sleeps for a while thread that increments an int for a while thread that does math.factorial on a large number. It calls start on the threads, then join with a timeout The sleep and spin threads work as expected and return from start right away, and then sit in the join for the timeout. The factorial thread on the other hand does not return from start until it runs to the end! import sys from threading import Thread from time import sleep, time from math import factorial # Helper class that stores a start time to compare to class timed_thread(Thread): def __init__(self, time_start): Thread.__init__(self) self.time_start = time_start # Thread that just executes sleep() class sleep_thread(timed_thread): def run(self): sleep(15) print "st DONE:\t%f" % (time() - time_start) # Thread that increments a number for a while class spin_thread(timed_thread): def run(self): x = 1 while x < 120000000: x += 1 print "sp DONE:\t%f" % (time() - time_start) # Thread that calls math.factorial with a large number class factorial_thread(timed_thread): def run(self): factorial(50000) print "ft DONE:\t%f" % (time() - time_start) # the tests print print "sleep_thread test" time_start = time() st = sleep_thread(time_start) st.start() print "st.start:\t%f" % (time() - time_start) st.join(2) print "st.join:\t%f" % (time() - time_start) print "sleep alive:\t%r" % st.isAlive() print print "spin_thread test" time_start = time() sp = spin_thread(time_start) sp.start() print "sp.start:\t%f" % (time() - time_start) sp.join(2) print "sp.join:\t%f" % (time() - time_start) print "sp alive:\t%r" % sp.isAlive() print print "factorial_thread test" time_start = time() ft = factorial_thread(time_start) ft.start() print "ft.start:\t%f" % (time() - time_start) ft.join(2) print "ft.join:\t%f" % (time() - time_start) print "ft alive:\t%r" % ft.isAlive() And here is the output on Python 2.6.5 on CentOS x64: sleep_thread test st.start: 0.000675 st.join: 2.006963 sleep alive: True spin_thread test sp.start: 0.000595 sp.join: 2.010066 sp alive: True factorial_thread test ft DONE: 4.475453 ft.start: 4.475589 ft.join: 4.475615 ft alive: False st DONE: 10.994519 sp DONE: 12.054668 I've tried this on python 2.6.5 on CentOS x64, 2.7.2 on Windows x86 and the factorial thread does not return from start on either of them until the thread is done executing. I've also tried this with PyPy 1.8.0 on Windows x86, and there result is slightly different. The start does return immediately, but then the join doesn't time out! sleep_thread test st.start: 0.001000 st.join: 2.001000 sleep alive: True spin_thread test sp.start: 0.000000 sp DONE: 0.197000 sp.join: 0.236000 sp alive: False factorial_thread test ft.start: 0.032000 ft DONE: 9.011000 ft.join: 9.012000 ft alive: False st DONE: 12.763000

    Read the article

  • How to set and get the id for the items in the spinner in Android

    - by Haresh Chaudhary
    I have a problem in my project that i am displaying a activity which would contain the details of the project which is previously added in Project Management System.. Now the fields in it are like: Fields of the Activity Name Of Project: ABC(EditText) Name Of Developer : ________(Spinner) Deadline : ________(Date Picker) Created On : _______(TextView) . . Now, the Spinner contains the Names of all developers working in the Company..I have used the ArrayAdapter with a array having the names of all the developers which is fetched from the database.. The problem is that when i update the Name Of Developer field, i get Only the Name of the Developer which is not enough to update the data as their can be multiple developers with the same name in the Company..So now I require the id of the developers to update it.. How to store that id of the developers with the Spinner so that i can achieve this.. Please help me to sort this out. Actually what i want to do like is as that we do in html:: <select> <option id="1">Developer1</option> <option id="2">Developer2</option> <option id="3">Developer2</option> <option id="4">Developer2</option> </select> where the id attached would be the database id....I want to imitate this in our android.... This the code that i have used to store the names in the array:: String alldevelopers = null; try { ArrayList<NameValuePair> postP = new ArrayList<NameValuePair>(); alldevelopers = CustomHttpClient.executeHttpPost( "/fetchdevelopers.php", postP); String respcl = alldevelopers.toString(); alldevelopersParser dev = new alldevelopersParser(); ow = dev.parseByDOM(respcl); } catch (Exception e) { e.printStackTrace(); } String developers[] = new String[ow.length]; //dev is a class object for (int n = 0; n < ow.length; n++) { developers[n] = ow.developer[n][2]; } This is the Spinner that would spin the array.. final Spinner devl = (Spinner) findViewById(R.id.towner); devl.setOnItemSelectedListener(managetasks.this); ArrayAdapter<String> b = new ArrayAdapter<String>getApplicationContext(), android.R.layout.simple_spinner_item,developers); b.setDropDownViewResource(android.R.layout.simple_dropdown_item_1line); devl.setAdapter(b);

    Read the article

< Previous Page | 13 14 15 16 17 18 19  | Next Page >