Search Results

Search found 12481 results on 500 pages for 'date picker'.

Page 172/500 | < Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >

• Netdom to restore machine secret

  - by icelava

  I have a number of virtual machines that have not been switched on for over a month, and some others which have been rolled back to an older state. They are members of a domain, and have expired their machine secrets; thus unable to authenticate with the domain any longer. Event Type: Warning Event Source: LSASRV Event Category: SPNEGO (Negotiator) Event ID: 40960 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: The Security System detected an authentication error for the server ldap/iceland.icelava.home. The failure code from authentication protocol Kerberos was "The attempted logon is invalid. This is either due to a bad username or authentication information. (0xc000006d)". For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c000006d Event Type: Warning Event Source: LSASRV Event Category: SPNEGO (Negotiator) Event ID: 40960 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: The Security System detected an authentication error for the server cifs/iceland.icelava.home. The failure code from authentication protocol Kerberos was "The attempted logon is invalid. This is either due to a bad username or authentication information. (0xc000006d)". For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c000006d Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 3210 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: This computer could not authenticate with \\iceland.icelava.home, a Windows domain controller for domain ICELAVA, and therefore this computer might deny logon requests. This inability to authenticate might be caused by another computer on the same network using the same name or the password for this computer account is not recognized. If this message appears again, contact your system administrator. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c0000022 So I try to use netdom to re-register the machine back to the domain C:\Documents and Settings\Administrator>netdom reset tfs2008wdata /domain:icelava /UserO:enterpriseadmin /PasswordO:mypassword Logon Failure: The target account name is incorrect. The command failed to complete successfully. But have not been successful. I wonder what else needs to be done?

  Read the article

• How to manage credentials on multiserver environment

  - by rush

  I have a some software that uses its own encrypted file for password storage ( such as ftp, web and other passwords to login to external systems, there is no way to use certificates ). On each server I've several instances of this software, each instance has its own password file. At the moment number of servers is permanently growing and it's getting harder and harder to manage all passwords on all instances up to date. Unfortunately, some servers are in cegregated network and there is no access from them to some centralized storage, but it works vice versa. My first idea was to create a git repository, encrypt each password with gpg and store it there and deliver it within deployment system, but security team was not satisfied with this idea and as it is insecure to store passwords in repository even in encrypted view ( from their words ). Nothing similar comes to my mind. Is there any way to implement safe and secure password storage with minimal effort to manage all passwords up-to-date? ps. if that matters I've red hat everywhere.

  Read the article

• Prevent Outlook from automatically deleting meeting emails

  - by Wavy Crab

  I'm using Outlook Web Access to read my email. When I receive a meeting notice and acknowledge it, Outlook adds it to my calendar then deletes the email. Is there a way to disable Outlook automatically deleting the meeting email? There doesn't seem to be any way to configure this in Options - Messaging and Options - Calendar. Note that I'm using Outlook Web Access and not the desktop client. From the copyright date this appears to be Outlook 2007. Follow-up: Based on edusysadmin's comment I logged-in using IE8, which exposed a setting not available in Firefox - "Move out-of-date meeting requests and responses to the Deleted Items folder". However unchecking this box doesn't seem to impact the auto-delete behavior. Follow-up 2: Keep in mind I am using Outlook Web Access via a web browser. I do not have the thick client Outlook installed.

  Read the article

• Powershell script for setting password expiry

  - by Pierre E

  Due to mistakes by the helpdesk staff, I found that over a 100 user accounts in my company AD have been set so that their passwords never expire. To avoid the situation in which all these users suddenly find themselves unable to log in, I want to run a script to set the password expiry to a specified date. I'm using Quest AD cmdlets, but I've only used powershell for simple scripts to get lists of users. The attribute I'm trying to modify is 'PasswordStatus' and I want to set those with this attribute set as "password never expires' to a specific date. Not much of a scripting guy, so any help in this would be most welcome.

  Read the article

• DKIM, SPF, PTR records are not working properly with my domain

  - by shihon

  I configured my server and well authenticate email system with DKIM key, SPF record and PTR records, when i start to sent out mails from phplist interface to my users ~50000, my domain is spammed by google. In headers, signed by and mailed by tag shows by my domain : appmail.co, I also test my domain via check mail provide by port25, report is: This message is an automatic response from Port25's authentication verifier service at verifier.port25.com. The service allows email senders to perform a simple check of various sender authentication mechanisms. It is provided free of charge, in the hope that it is useful to the email community. While it is not officially supported, we welcome any feedback you may have at . Thank you for using the verifier, The Port25 Solutions, Inc. team ========================================================== Summary of Results SPF check: pass DomainKeys check: neutral DKIM check: pass Sender-ID check: pass SpamAssassin check: ham ========================================================== Details: HELO hostname: app.appmail.co Source IP: 108.179.192.148 mail-from: [email protected] SPF check details: Result: pass ID(s) verified: [email protected] DNS record(s): appmail.co. SPF (no records) appmail.co. 14400 IN TXT "v=spf1 +a +mx +ip4:108.179.192.148 ?all" appmail.co. 14400 IN A 108.179.192.148 DomainKeys check details: Result: neutral (message not signed) ID(s) verified: [email protected] DNS record(s): DKIM check details: Result: pass (matches From: [email protected]) ID(s) verified: header.d=appmail.co Canonicalized Headers: content-type:multipart/alternative;'20'boundary=047d7b2eda75d8544d04c17b6841'0D''0A' to:[email protected]'0D''0A' from:shashank'20'sharma'20'<[email protected]>'0D''0A' subject:Test'0D''0A' message-id:<CADnDhbH9aDBk3Ho2-CrG7gwOoD6RNX0sFq4bWL64+kmo=9HjWg@mail.gmail.com>'0D''0A' date:Sat,'20'2'20'Jun'20'2012'20'16:44:50'20'+0530'0D''0A' mime-version:1.0'0D''0A' dkim-signature:v=1;'20'a=rsa-sha256;'20'q=dns/txt;'20'c=relaxed/relaxed;'20'd=appmail.co;'20's=default;'20'h=Content-Type:To:From:Subject:Message-ID:Date:MIME-Version;'20'bh=GS6uwlT+weKcrrLJ2I+cjBtWPq9nvhwRlNAJebOiQOk=;'20'b=; Canonicalized Body: --047d7b2eda75d8544d04c17b6841'0D''0A' Content-Type:'20'text/plain;'20'charset=UTF-8'0D''0A' '0D''0A' Hello'20'Senders'0D''0A' '0D''0A' --047d7b2eda75d8544d04c17b6841'0D''0A' Content-Type:'20'text/html;'20'charset=UTF-8'0D''0A' '0D''0A' Hello'20'Senders'0D''0A' '0D''0A' --047d7b2eda75d8544d04c17b6841--'0D''0A' DNS record(s): default._domainkey.appmail.co. 14400 IN TXT "v=DKIM1; k=rsa; p=MHwwDQYJKoZIhvcNAQEBBQADawAwaAJhALGCOdMeZRxRHoatH7/KCvI1CKS0wOOsTAq0LLgPsOpMolifpVQDKOWT2zq/6LHVmDVjXLbnWO2d4ry/riy7ei66pLpnAV5ceIUSjBRusI8jcF9CZhPrh/OImsKVUb9ceQIDAQAB;" NOTE: DKIM checking has been performed based on the latest DKIM specs (RFC 4871 or draft-ietf-dkim-base-10) and verification may fail for older versions. If you are using Port25's PowerMTA, you need to use version 3.2r11 or later to get a compatible version of DKIM. Sender-ID check details: Result: pass ID(s) verified: [email protected] DNS record(s): appmail.co. SPF (no records) appmail.co. 14400 IN TXT "v=spf1 +a +mx +ip4:108.179.192.148 ?all" appmail.co. 14400 IN A 108.179.192.148 SpamAssassin check details: SpamAssassin v3.3.1 (2010-03-16) Result: ham (-0.1 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- -0.0 T_RP_MATCHES_RCVD Envelope sender domain matches handover relay domain 0.0 HTML_MESSAGE BODY: HTML included in message -0.5 BAYES_05 BODY: Bayes spam probability is 1 to 5% [score: 0.0288] -0.1 DKIM_VALID_AU Message has a valid DKIM or DK signature from author's domain 0.1 DKIM_SIGNED Message has a DKIM or DK signature, not necessarily valid -0.1 DKIM_VALID Message has at least one valid DKIM or DK signature 0.5 SINGLE_HEADER_1K A single header contains 1K-2K characters ========================================================== Original Email Return-Path: <[email protected]> Received: from app.appmail.co (108.179.192.148) by verifier.port25.com id hp7qqo11u9cc for <[email protected]>; Sat, 2 Jun 2012 07:14:52 -0400 (envelope-from <[email protected]>) Authentication-Results: verifier.port25.com; spf=pass [email protected] Authentication-Results: verifier.port25.com; domainkeys=neutral (message not signed) [email protected] Authentication-Results: verifier.port25.com; dkim=pass (matches From: [email protected]) header.d=appmail.co Authentication-Results: verifier.port25.com; sender-id=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=appmail.co; s=default; h=Content-Type:To:From:Subject:Message-ID:Date:MIME-Version; bh=GS6uwlT+weKcrrLJ2I+cjBtWPq9nvhwRlNAJebOiQOk=;b=pNw3UQNMoNyZ2Ujv8omHGodKVu/55S8YdBEsA5TbRciga/H7f+5noiKvo60vU6oXYyzVKeozFHDoOEMV6m5UTgkdBefogl+9cUIbt5CSrTWA97D7tGS97JblTDXApbZH; Received: from mail-pb0-f46.google.com ([209.85.160.46]:57831) by app.appmail.co with esmtpa (Exim 4.77) (envelope-from <[email protected]>) id 1SamIF-00055f-Om for [email protected]; Sat, 02 Jun 2012 16:44:51 +0530 Received: by pbbrp8 with SMTP id rp8so4165728pbb.5 for <[email protected]>; Sat, 02 Jun 2012 04:14:51 -0700 (PDT) MIME-Version: 1.0 Received: by 10.68.216.33 with SMTP id on1mr19414885pbc.105.1338635690988; Sat, 02 Jun 2012 04:14:50 -0700 (PDT) Received: by 10.143.66.13 with HTTP; Sat, 2 Jun 2012 04:14:50 -0700 (PDT) Date: Sat, 2 Jun 2012 16:44:50 +0530 Message-ID: <CADnDhbH9aDBk3Ho2-CrG7gwOoD6RNX0sFq4bWL64+kmo=9HjWg@mail.gmail.com> Subject: Test From: shashank sharma <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=047d7b2eda75d8544d04c17b6841 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - app.appmail.co X-AntiAbuse: Original Domain - verifier.port25.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - appmail.co --047d7b2eda75d8544d04c17b6841 Content-Type: text/plain; charset=UTF-8 Hello Senders --047d7b2eda75d8544d04c17b6841 Content-Type: text/html; charset=UTF-8 Hello Senders --047d7b2eda75d8544d04c17b6841-- I also tried to send mail on yahoo , rediff but i get mails in spam. Please help me to sort out this issue

  Read the article

• Prevent Outlook from automatically deleting meeting emails

  - by Wavy Crab

  I'm using Outlook Web Access to read my email. When I receive a meeting notice and acknowledge it, Outlook adds it to my calendar then deletes the email. Is there a way to disable Outlook automatically deleting the meeting email? There doesn't seem to be any way to configure this in Options - Messaging and Options - Calendar. Note that I'm using Outlook Web Access and not the desktop client. From the copyright date this appears to be Outlook 2007. Follow-up: Based on edusysadmin's comment I logged-in using IE8, which exposed a setting not available in Firefox - "Move out-of-date meeting requests and responses to the Deleted Items folder". However unchecking this box doesn't seem to impact the auto-delete behavior. Follow-up 2: Keep in mind I am using Outlook Web Access via a web browser. I do not have the thick client Outlook installed.

  Read the article

• Solaris Non global Zone x server

  - by ankimal

  I am not even sure if this is possible but how can I start an X server on a non-global zone? If I run startx from within my zone. I created the xorg.conf by running /usr/X11/bin/xorgconfig root@foo:/usr/X11/bin# startx xauth: creating new authority file /root/.serverauth.20957 X.Org X Server 1.5.3 Release Date: 5 November 2008 X Protocol Version 11, Revision 0 Build Operating System: SunOS 5.11 snv_108 i86pc Current Operating System: SunOS dsol101 5.11 snv_111b i86pc Build Date: 07 May 2009 04:44:56PM Solaris ABI: 64-bit SUNWxorg-server package version: 6.9.0.5.11.11100,REV=0.2009.05.07 SUNWxorg-mesa package version: 6.9.0.5.11.11100,REV=0.2009.04.02 Before reporting problems, check http://sunsolve.sun.com/ to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue Nov 10 19:17:53 2009 (==) Using config file: "/etc/X11/xorg.conf" Fatal server error: xf86OpenConsole: Cannot open /dev/fb (No such file or directory)

  Read the article

• PHP Mail() to Gmail = Spam

  - by grantw

  Recently Gmail has started marking emails sent directly from my server (using php mail()) as spam and I'm having problems trying to find the issue. If I send an exact copy of the same email from my email client it goes to the Gmail inbox. The emails are plain text, around 7 lines long and contain a URL link in plain text. As the emails sent from my client are getting through fine I'm thinking that the content isn't the issue. It would be greatly appreciated if someone could take a look at the the following headers and give me some advice why the email from the server is being marked as spam. Email from Server: Delivered-To: [email protected] Received: by 10.49.98.228 with SMTP id el4csp101784qeb; Thu, 15 Nov 2012 14:58:52 -0800 (PST) Received: by 10.60.27.166 with SMTP id u6mr2296595oeg.86.1353020331940; Thu, 15 Nov 2012 14:58:51 -0800 (PST) Return-Path: [email protected] Received: from dom.domainbrokerage.co.uk (dom.domainbrokerage.co.uk. [174.120.246.138]) by mx.google.com with ESMTPS id df4si17005013obc.50.2012.11.15.14.58.51 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 15 Nov 2012 14:58:51 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) client-ip=174.120.246.138; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=domainbrokerage.co.uk; s=default; h=Date:Message-Id:Content-Type:Reply-to:From:Subject:To; bh=2RJ9jsEaGcdcgJ1HMJgQG8QNvWevySWXIFRDqdY7EAM=; b=mGebBVOkyUhv94ONL3EabXeTgVznsT1VAwPdVvpOGDdjBtN1FabnuFi8sWbf5KEg5BUJ/h8fQ+9/2nrj+jbtoVLvKXI6L53HOXPjl7atCX9e41GkrOTAPw5ZFp+1lDbZ; Received: from grantw by dom.domainbrokerage.co.uk with local (Exim 4.80) (envelope-from [email protected]) id 1TZ8OZ-0008qC-Gy for [email protected]; Thu, 15 Nov 2012 22:58:51 +0000 To: [email protected] Subject: Offer Accepted X-PHP-Script: www.domainbrokerage.co.uk/admin.php for 95.172.231.27 From: My Name [email protected] Reply-to: [email protected] Content-Type: text/plain; charset=Windows-1251 Message-Id: [email protected] Date: Thu, 15 Nov 2012 22:58:51 +0000 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - dom.domainbrokerage.co.uk X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [500 500] / [47 12] X-AntiAbuse: Sender Address Domain - domainbrokerage.co.uk X-Get-Message-Sender-Via: dom.domainbrokerage.co.uk: authenticated_id: grantw/from_h Email from client: Delivered-To: [email protected] Received: by 10.49.98.228 with SMTP id el4csp101495qeb; Thu, 15 Nov 2012 14:54:49 -0800 (PST) Received: by 10.182.197.8 with SMTP id iq8mr2351185obc.66.1353020089244; Thu, 15 Nov 2012 14:54:49 -0800 (PST) Return-Path: [email protected] Received: from dom.domainbrokerage.co.uk (dom.domainbrokerage.co.uk. [174.120.246.138]) by mx.google.com with ESMTPS id ab5si17000486obc.44.2012.11.15.14.54.48 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 15 Nov 2012 14:54:49 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) client-ip=174.120.246.138; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=domainbrokerage.co.uk; s=default; h=Content-Transfer-Encoding:Content-Type:Subject:To:MIME-Version:From:Date:Message-ID; bh=bKNjm+yTFZQ7HUjO3lKPp9HosUBfFxv9+oqV+NuIkdU=; b=j0T2XNBuENSFG85QWeRdJ2MUgW2BvGROBNL3zvjwOLoFeyHRU3B4M+lt6m1X+OLHfJJqcoR0+GS9p/TWn4jylKCF13xozAOc6ewZ3/4Xj/YUDXuHkzmCMiNxVcGETD7l; Received: from w-27.cust-7941.ip.static.uno.uk.net ([95.172.231.27]:1450 helo=[127.0.0.1]) by dom.domainbrokerage.co.uk with esmtpa (Exim 4.80) (envelope-from [email protected]) id 1TZ8Ke-0001XH-7p for [email protected]; Thu, 15 Nov 2012 22:54:48 +0000 Message-ID: [email protected] Date: Thu, 15 Nov 2012 22:54:50 +0000 From: My Name [email protected] User-Agent: Postbox 3.0.6 (Windows/20121031) MIME-Version: 1.0 To: [email protected] Subject: Offer Accepted Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - dom.domainbrokerage.co.uk X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - domainbrokerage.co.uk X-Get-Message-Sender-Via: dom.domainbrokerage.co.uk: authenticated_id: [email protected]

  Read the article

• Unicast traffic between hosts on a switch leaving the switch by its uplink. Why?

  - by Rich Lafferty

  I have a weird thing happening on our network at my office which I can't quite get my head around. In particular I can't tell if it's a problem with a switch, or a problem with configuration. We have a Cisco SG300-52 switch (sw01) in the top of a rack in our server room, connected to another SG300-28 that acts as our core switch (core01). Both run layer 2 only, our firewalls do routing between VLANs. They have a dozen or so VLANs between them. Gi1 on sw01 is a trunk port connected to gi1 on core01. (Disclosure: There are other switches in our environment but I'm pretty sure I've isolated the problem down to these two. Happy to provide more info if necessary.) The behaviour I'm seeing is limited to one VLAN, vlan 12 -- or, at least, it's not happening on the other ones I checked (It's hard to guarantee the absence of packets), and it is: sw01 is forwarding, to core01, traffic which is between two hosts which are both plugged into sw01. (I noticed this because the IDS in our firewall gave a false positive on traffic which should not reach the firewall.) We noticed this mostly between our two dhcp/dns servers, net01 (10.12.0.10) and net02 (10.12.0.11). net01 is physical hardware and net02 is on a VMware ESX server. net01 is connected to gi44 on sw01 and net02's ESX server to gi11. [net01]----gi44-[sw01]-gi1----gi1-[core01] [net02]----gi11/ Let's see some interfaces! Remember, vlan 12 is the problem vlan. Of the others I explicitly verified that vlan 27 was not affected. Here's the two hosts' ports: esx01 contains net02. sw01#sh run int gi11 interface gigabitethernet11 description esx01 lldp med disable switchport trunk allowed vlan add 5-7,11-13,100 switchport trunk native vlan 27 ! sw01#sh run int gi44 interface gigabitethernet44 description net01-1 lldp med disable switchport mode access switchport access vlan 12 ! Here's the trunk on sw01. sw01#sh run int gi1 interface gigabitethernet1 description "trunk to core01" lldp med disable switchport trunk allowed vlan add 4-7,11-13,27,100 ! And the other end of the trunk on core01. interface gigabitethernet1 description sw01 macro description switch switchport trunk allowed vlan add 2-7,11-16,27,100 ! I have a monitor port on core01, thus: core01#sh run int gi12 interface gigabitethernet12 description "monitor port" port monitor GigabitEthernet 1 ! And the monitor port on core01 sees unicast traffic going between net01 and net02, both of which are on sw01! I've verified this with a monitor port on sw01 that sees the net01-net02 unicast traffic leaving via gi1 too. sw01 knows that both of those hosts are on ports that are not its trunk port: :) ratchet$ arp -a | grep net net02.2ndsiteinc.com (10.12.0.11) at 00:0C:29:1A:66:15 [ether] on eth0 net01.2ndsiteinc.com (10.12.0.10) at 00:11:43:D8:9F:94 [ether] on eth0 sw01#sh mac addr addr 00:0C:29:1A:66:15 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:0c:29:1a:66:15 gi11 dynamic sw01#sh mac addr addr 00:11:43:D8:9F:94 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:11:43:d8:9f:94 gi44 dynamic I also brought up an unused port on sw01 on vlan 12, but the unicast traffic was (as best as I could tell) not coming out that port. So it doesn't look like sw01 is pushing it out all its ports, just the right ports and also gi1! I've verified that sw01 is not filling up its address-table: sw01#sh mac addr count This may take some time. Capacity : 8192 Free : 7983 Used : 208 The full configs for both core01 and sw01 are available: core01, sw01. Finally, versions: sw01#sh ver SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 ) Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 ) HW version V01 core01#sh ver SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 ) Boot version 1.1.0.6 ( date 11-May-2011 time 18:31:00 ) HW version V01 So my understanding is this: sw01 should take unicast traffic for net01 and send it only out net02's port, and vice versa; none of it should go out sw01's uplink. But core01, receiving traffic on gi1 for a host it knows is on gi1, is right in sending it out all of its ports. (That is: sw01 is misbehaving, but core01 is doing what it should given the circumstances.) My question is: Why is sw01 sending that unicast traffic out its uplink, gi1? (And pre-emptively: yes, I know SG300s leave much to be desired, and yes, we should have spanning-tree enabled, but that's where I'm at right now.)

  Read the article

• china and gmail attacks

  - by doug

  "We have evidence to suggest that a primary goal of the attackers was accessing the Gmail accounts of Chinese human rights activists. Based on our investigation to date we believe their attack did not achieve that objective. Only two Gmail accounts appear to have been accessed, and that activity was limited to account information (such as the date the account was created) and subject line, rather than the content of emails themselves.” [source] I don't know much about how internet works, but as long the chines gov has access to the chines internet providers servers, why do they need to hack gmail accounts? I assume that i don't understand how submitting/writing a message(from user to gmail servers) works, in order to be sent later to the other email address. Who can tell me how submitting a message to a web form works?

  Read the article

• Use a webpage as a screen saver

  - by Stephen

  We have a number of retail stores that sell laptops. There are a number of display models on show in each retail store. At the moment screen savers are used to promote different offers and these screen savers are out of date. What I would like to do is open up a browser on these machines and just use a webpage. This way I can control exactly what is displayed and keep it up to date with our latest offers. Is it possible to have the webpage in full screen mode, with no address bar or tabs visible. As far as I'm aware these are Windows machines, probably running Windows Vista or Windows 7. Any help appreciated.

  Read the article

• Error with FTP since binding via httpcfg

  - by Linda

  I was in a similar posistion to this question and bound two IP addresses using httpcfg. Since doing this ftp does not seem to be working on IIS6 in Windows Server 2003. Any ideas what could be wrong? The command I ran was: httpcfg set iplisten -i xxx.xxx.x.x I get the following when I try to conenct via Filezilla: Error: Connection timed out Error: Failed to retrieve directory listing The log file is returning the following: #Software: Microsoft Internet Information Services 6.0 #Version: 1.0 #Date: 2009-08-17 13:54:05 #Fields: date time c-ip cs-username cs-method cs-uri-stem sc-status sc-win32-status 2009-08-17 13:54:05 91.85.70.17 Client [1]USER Client 331 0 2009-08-17 13:54:05 91.85.70.17 Client [1]PASS - 230 0 In the ftp site settings I have the site pointing to the IP address used using httpcfg and the port set to 21. Update: I can see a directory listing if I connect via the inbuilt commandline ftp client in wondows vista. If I try to connect via a windows explorer I start in the incorrect folder and no files are listed just directories.

  Read the article

• How to avoid tilde ~ in Bash prompt?

  - by Jirka

  Hello! I have set my prompt in bash in a such way that I can use it directly in scp command: My current PS1 string: PS1="\h:\w\n$" And the prompt looks like this: lnx-hladky:/tmp/plugtmp $ What I don't like at all is the fact that $HOME directory is displayed as tilde. Can this be avoided? It's causing problems when switching between different users. Example: lnx-hladky:~/DOC $ Documentation says: \w : the current working directory, with $HOME abbreviated with a tilde \W: the basename of the current working directory, with $HOME abbreviated with a tilde Is there any possibility to avoid $HOME being abbreviated with a tilde? I have found one way around but I feel like it's overcomplicated: PROMPT_COMMAND='echo -ne "\e[4;35m$(date +%T)\e[24m$(whoami)@$(hostname):$(pwd)\e[m\n"' PS1=$ Can anyone propose a better solution? I have a feeling it's not quite OK to run so many commands just to get prompt. (date,whoami,hostname,pwd). Thanks a lot! Jirka

  Read the article

• Two timer applets in notification area

  - by 1passenger

  Hi, after installig Ubuntu 10.04 Remix I can see two timer applets in the notification area. When I click on the first one, I can see the current date and the menues "Open Calendar", "Set Time and Date". When I click on the second one, I can see a small calendar of the current month and a small world map with my defined locations. I just want to have only one timer to safe some space in the notification area. How to disable one of the two applets? To click "Remove from Panel" isn't possible in the Remix edition!

  Read the article

• send command to an already running screen session

  - by aXon

  Hi I have been trying to send commands to a running gnu screen session (4.00.03) in opensolaris, but cannot get it to run any commands through any combination of screen -X Ok, I start a screen session with screen -S test, and then tried to with screen -r -X "date"to just show me the date, when I would reconnect to it. But neither an error message nor output in the screen happened. I tried with so many combinations, that I can't even remember. Any hints on how to accomplish it? The reason why I am doing this is, because I have a program, which does not come as a daemon, and I wish to start it in a screen session, so I can later on see what is going on.

  Read the article

• BSOD 0x000000f4(Probably caused by : wininit.exe)

  - by vacuum

  I have BSOD with 0x000000f4 code. It appears when system is not loaded at all. No new hardware where intalled. Only nvidia drivers where updated 3 days ago and they are up to date for now(version 296.10). System Health Report(perfmon /report) shows nothing interesting(only complained on disabled UAC) System is on SSD disk(WDC SSC-D0064SC-2100 B) Dump Spec: OS Name Microsoft Windows 7 Ultimate Version 6.1.7601 Service Pack 1 Build 7601 System Manufacturer Gigabyte Technology Co., Ltd. System Model P31-DS3L System Type x64-based PC Processor Intel(R) Core(TM)2 Duo CPU E7200 @ 2.53GHz, 2534 Mhz, 2 Core(s), 2 Logical Processor(s) BIOS Version/Date Award Software International, Inc. F9, 10.07.2008 Any suggestions?

  Read the article

• mail server administration

  - by kibs

  MY postfix does not show that it is listening to the smtp daemon getting mesaage below: The message WAS NOT relayed Reporting-MTA: dns; mail.mak.ac.ug Received-From-MTA: smtp; mail.mak.ac.ug ([127.0.0.1]) Arrival-Date: Wed, 19 May 2010 12:45:20 +0300 (EAT) Original-Recipient: rfc822;[email protected] Final-Recipient: rfc822;[email protected] Action: failed Status: 5.4.0 Remote-MTA: dns; 127.0.0.1 Diagnostic-Code: smtp; 554 5.4.0 Error: too many hops Last-Attempt-Date: Wed, 19 May 2010 12:45:20 +0300 (EAT) Final-Log-ID: 23434-08/A38QHg8z+0r7 undeliverable mail MTA BLOCKED OUTPUT FROM lsof -i tcp:25 command master 3014 root 12u IPv4 9429 TCP *:smtp (LISTEN) (Postfix as a user is missing )

  Read the article

• Set default expand/colapse state on pivot tables

  - by CLockeWork

  The Setup I have a pivot table in tabular form pulling data from an Analysis Services Cube. I want to calculate the number of days between two dates, but the setup will only allow me to pull in all date elements, not just the date. I’ve been able to deal with this easily enough by just grouping all the columns: The Problem The default state for the expand/collapse buttons in the image above is often collapsed, but that means the dates I need aren’t there and you have to open the group and manually expand them. This also happens in some random ways (as shown in the image) where only some rows expand. The Question I need a way to set these sections to always be expanded, so that the user never has to open the group to expand the rows. Ideally I’d like to avoid VBA because our end users often block it, but if that’s what’s needed then so be it. Is there a way to set my pivot table to never collapse it’s predefined groups? Note the end user is using Excel 2010

  Read the article

• Windows Server 2012 R2 application installation slowness

  - by Eric

  Good afternoon, Windows Server 2012 R2 as host fully up to date Windows Server 2012 R2 as guest fully up to date Whether I am running it as a host or guest, whenever I am installing an application that should take a couple minutes it always ends up 3x-5x longer than it should. If I take the same applications and install it on any other OS (IE 2k8, 7,) it they install very quickly. Dell server management software took 30 minutes or so when it takes 5 minutes or so on 2k8. Even a clean install not joined to domain I still experience this same slowness on applications I attempt to install. So my question to everyone is, are you or anyone else experiencing this? I cannot find anything on google so this is why I am here

  Read the article

• Temp profile used when User logs in

  - by TJ

  One of my users logged into his computer, Windows XP, last night only to be meet with an error message that it could not load his profile and he will be logged in using a temporary profile. Typically when this happens I shut the machine down and restart and the correct profile will load when they log in again. Not this time. In the user profile options under computer-properties-Advanced-user profiles it show that there are three profiles with his name. Two are the exact same size with the same modified date (5/5/10) and the other is what I would expect size wise for a new profile with a modified date of today. What are my options to restore his profile?

  Read the article

• Deployment Workbench no longer available after PXE boot

  - by Patrick

  Our build process revolves around windows Deployment Workbench. Unfortunately this was setup by someone who is no longer with the company, and no-one has ever dared/needed to make any changes. The other day it stopped working. It turns out that one of our build guys started thinking about changing some stuff in it, clicked something and now it no longer works (He is saying now that he right clicked on the 'LAB' entry in 'Deployment points' and hit 'Update', which took some time to run through apparently). The job has fallen on me to resolve and frankly I'm not sure what I'm doing. I was wondering if someone with more experience than me can provide some pointers as to troubleshooting cos I'm feeling quite a lot in the dark here. On the server I have Deployment Workbench up and running (MMC snapin) version 3.0. There is a WDS service that appears to be running ok, as does the tFTPd service. Nothing specific to this in event logs. From the client side; PXE boot works and gets you to the Win PE launch, and it has the correct company logo as the background (proving to me that its loading win PE from the network). WPEINIT runs, and asks for domain credentials, here the team simply put User/Pass/Domain in the boxes and click ok. Normally the build would kick off. Instead they get an error message saying that the \NATBLU01\Distribution$ share isn't available. Checking \NATBLU01\Distribution$ shows that its there and accessible over the network. Security/permissions seem ok, even 'ANONYMOUS LOGON' has read access to that share so I don't see that being a problem. Digging the trace files from C:\MININT\SMSOSD\OSDLOGS\ after an attempt to run the build I can see an error saying much the same - <![LOG[Validating connection to \\NATBLU01\Distribution$]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[FindFile: The file OSDConnectToUNC.exe could not be found in any standard locations.]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[The network location cannot be reached. For information about network troubleshooting, see Windows Help.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> <![LOG[ERROR - Unable to map a network drive to \\NATBLU01\Distribution$.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> BDD.LOG shows much the same. Full copies of the .LOG files can both files be found here : BDD.LOG LITETOUCH.LOG I can get to a command prompt from the Win PE that boots from PXE, however there isn't any network stuff there. IPCONFIG returns nothing so none of the tests I would usually run resolve anything. I'm at a loss frankly. I did wonder if I could perhaps start a new build process but if the change to the DeploymentWorkbench has knocked it offline I don't think I'm going to be able to create a new deployment. Failing that; we do have a deployment point labeled type 'Media' which appears to be a DVD ISO image of one of the builds, but its dated 2008, is it possible to export the network build to .ISO and build from DVD? We are looking at new hardware to run this from anyway (for the impending Windows 7 roll out) so a temporary work round isn't going to be too much of a problem. All assistance is appreciated! EDIT : OK. Got it working again. Solution was close to Newmanth's idea. The problem was that our PE image didn't appear to be connecting the network. I had an older copy of the PE boot.WIM on a stick that I had been using for other purposes. I booted that and correctly got a network connection. Showed a correct internal IP and could ping out etc etc. However I was still getting the same errors in all the logs and in when wpeinit was running. What I did seperately was to update the PE image that DeploymentWorkbench was pushing out to display a different back ground. I wanted to prove that I was working in the correct place. Turns out that I wasn't. I went and looked at the other deployment stuff we had on this machine, Windows Deployment Services was installed and although all the install images are off line the boot image was online, so I uploaded the copy from my stick to that. Booted straight off. And fixed. Working. Yay! For anyone stumbling across this in the future you may find that although your deployment images are located in the DeploymentWorkbench, the Win PE boot image you are launching from is located in the associated Windows Deployment Services images.

  Read the article

• SNMP keeps crashing

  - by jldugger

  We're using OpsView/Nagios to monitor our servers. We've added the SNMP service to all our servers and deployed the configuration via GPO, but one win2k3 server seems to have a problem; it crashes pretty regularly. The event log carries messages like: Event Type: Error Event Source: Service Control Manager Event Category: None Event ID: 7034 Date: 6/11/2009 Time: 7:11:49 PM User: N/A Computer: HOSTNNAME Description: The SNMP Service service terminated unexpectedly. It has done this 2 time(s). and also Event Type: Error Event Source: Application Error Event Category: (100) Event ID: 1000 Date: 6/11/2009 Time: 7:11:18 PM User: N/A Computer: HOSTNAME Description: Faulting application snmp.exe, version 5.2.3790.3959, faulting module ntdll.dll, version 5.2.3790.3959, fault address 0x000417af. Now, I could probably set it to simply restart on crash in perpetuity, but I think it's better to fix problems like this. Is this a known problem? If not, what should I do to diagnose it?

  Read the article

• Windows Server 2003 W3SVC Failing, Brute Force attack possibly the cause

  - by Roaders

  This week my website has disappeared twice for no apparent reason. I logged onto my server (Windows Server 2003 Service Pack 2) and restarted the World Web Publishing service, website still down. I tried restarting a few other services like DNS and Cold Fusion and the website was still down. In the end I restarted the server and the website reappeared. Last night the website went down again. This time I logged on and looked at the event log. SCARY STUFF! There were hundreds of these: Event Type: Information Event Source: TermService Event Category: None Event ID: 1012 Date: 30/01/2012 Time: 15:25:12 User: N/A Computer: SERVER51338 Description: Remote session from client name a exceeded the maximum allowed failed logon attempts. The session was forcibly terminated. At a frequency of around 3 -5 a minute. At about the time my website died there was one of these: Event Type: Information Event Source: W3SVC Event Category: None Event ID: 1074 Date: 30/01/2012 Time: 19:36:14 User: N/A Computer: SERVER51338 Description: A worker process with process id of '6308' serving application pool 'DefaultAppPool' has requested a recycle because the worker process reached its allowed processing time limit. Which is obviously what killed the web service. There were then a few of these: Event Type: Error Event Source: TermDD Event Category: None Event ID: 50 Date: 30/01/2012 Time: 20:32:51 User: N/A Computer: SERVER51338 Description: The RDP protocol component "DATA ENCRYPTION" detected an error in the protocol stream and has disconnected the client. Data: 0000: 00 00 04 00 02 00 52 00 ......R. 0008: 00 00 00 00 32 00 0a c0 ....2..À 0010: 00 00 00 00 32 00 0a c0 ....2..À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 92 01 00 00 ... With no more of the first error type. I am concerned that someone is trying to brute force their way into my server. I have disabled all the accounts apart from the IIS ones and Administrator (which I have renamed). I have also changed the password to an even more secure one. I don't know why this brute force attack caused the webservice to stop and I don't know why restarting the service didn't fix the problem. What should I do to make sure my server is secure and what should I do to make sure the webserver doesn't go down any more? Thanks.

  Read the article

• Update notification for macports

  - by Space_C0wb0y

  Is there any way or tool that I can use to receive notifications when any of my macports-packages are out-of-date?

  Read the article

• What RSS Reader can handle item-updating (JIRA search) feeds?

  - by Stephen

  Thunderbird is a good rss reader in terms of being able to connect successfully to jira authenticated search feeds (where evolution-rss and Liferea can't), but really sucks when it comes to updating. A Jira search feed will give a link id to http://jira/browse/[ticket no], and if that ticket/feed-item is updated, thunderbird refuses to update it - it already has it! (even though the item date does not match). Also, if you delete the ticket update, it will never show up again for that news account. Has anybody found an RSS reader that can work with JIRA/updating RSS items? Note: this is not the same as Jira activity feeds - those work great, as each update has a unique item id To replicate: Grab a search (any search) Get it into your rss reader Read an item, modify the linked ticket Update rss and see if the ticket bumps to most recent and unread or, generically: Get an rss feed (from your hard drive?) Modify an item in the middle changing the content, the date, and moving it to the top Update rss and see if the ticket bumps to most recent and unread

  Read the article

< Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >