Search Results

Search found 7845 results on 314 pages for 'connected'.

Page 173/314 | < Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >

• Establish direct cable connection between Windows 8 PCs in home network

  - by Marie. P.

  I'm running two PCs, a desktop and a laptop with Windows 8 Release Preview ("Build 8400"). They are connected to the same router in infrastructure mode, thereby having wireless internet. Due to often file synchronization between the machines I want to establish a cable connection that allows direct file transfer, without needing to use the wireless. When I plug in the cable (normal, not cross-over), I see in "Control Panel\Network and Internet\Network Connections": "Ethernet - unidentified Network" on both PCs. Transferring a file between both still only uses the WiFi via the Router. I noticed that when turning off the wifi on one PC, I can set up a shared internet connection that will work via Ethernet-cable, but since sometimes only one PC runs, sometimes the other one, I do not want to have the internet of one machine to be dependent on the other one being switched on. I do not have a crossover-cable, but since I did connect the PCs already successfully (just without both being on the internet), I'm sure that this should also work with a normal ethernet cable.

  Read the article

• Windows 7 Won't connect to Wireless Router too far away (but still have 3 bars)

  - by Kerry

  I have found this problem a couple of times. Windows 7 with Intel AGN 5100 won't connect to a WPA2-PSK router when it's too far away. Both times I've had this happen I was in a foreign country (London and Stockholm), and both times I was upstairs while the router was downstairs. Now, it still has 2-3 bars when looking at local WiFi, but I get the "will not connect" error, and debugging doesn't help at all (it doesn't know what's wrong). I went downstairs and it connected immediately (but I need to be able to have it upstairs). My Android Cell Phone and iPad were able to connect upstairs just fine. Any suggestions?

  Read the article

• Router used as ethernet bridge wont show up

  - by user1255271

  I have a Netgear router in my living room that has the wireless signal. It is connected to a Powerline plug that goes up to my bedroom. That is plugged into another router that is used as an ethernet hub. It's cables go into my PS3 and my server. The second router shows up as a hidden network on my laptop, and I can connect to it. But it is not listed as an attached device on my main router, and my laptop says that it connects straight to the main router, not the second one. How can I connect to this router? Aside from swapping the two? Thanks in advance.

  Read the article

• How to reach a Global Scope IPv6 host?

  - by Vaibhav Bajpai

  I have setup DNS64+NAT64 on a machine with 2 interfaces: eth0: public IPv4 address (connected to outside world) eth1: global scope IPv6 address: 2001::/64 I can successfully use ping6 google.com on this machine. Now I want to connect my MacBook to this machine by making it an IPv6-only client and perform some tests, but I do not have an IPv6 address assigned on this MacBook. I'm wondering, how should I manually assign one so as to route all my IPv6 traffic (I will disable IPv4 on my MacBook) to this machine, which will be picked up by DNS64+NAT64 to be converted to IPv4 requests and sent to the outside world?

  Read the article

• Default user logon on Windows Server system

  - by Robert Koritnik

  I installed Remote Desktop Services role (ex Terminal Services) on my Windows Server 2008 R2 machine. After installation when I try to logon locally, there's no default user as it used to be. Can I tweak group policy to have my default user back? I did enable to remember last logon user, but it didn't work... Obviously RDS (ex TS) ignores this policy setting. Additional note: I'm not connected to a domain. It's a standalone development machine running server OS. No domain needed for it.

  Read the article

• Multiple connections to the same Wireless Network in Windows 7

  - by Jamek

  Hello, my university just limited bandwidth to 512 kbps (that's 64 kB/s!) for each connection. I was thinking to make multiple connection to the same wireless network (called "internet"), is this possible under Windows 7? I know it's possible to connect to more than one WLAN through the "hostednetwork" concept in netsh: netsh wlan set hostednetwork mode=allow ssid=xxxxx netsh wlan start hostednetwork However this method doesn't seem to work, I don't know if it's due to the authentication method (through certificates while hostednetwork seems to support just a "passphrase") or because I'm already connected to that network with the same MAC. Can you think to some tool able to do this?

  Read the article

• How to connect Microsoft Bluetooth Mouse 5000 to Windows 7?

  - by davidshen84

  I have a Microsoft Bluetooth 5000 mouse, and I used it with my Linux and Windows 7 system. In Linux, the mouse can always connect to the system normally. But on Windows 7, after I have successfully added the mouse to Windows 7, if I have connected the mouse to the Linux system, it will not be able to connect to the Windows 7 system any more - unless I remove the mouse and add it again. I tried to play all settings I could find in the Bluetooth settings on Windows 7, but cannot fix this problem. How can I use the mouse without having to remove and add it again ?

  Read the article

• Why is the pavucontrol level indicator jumping while nothing plays?

  - by EnterTheLiquidToasterFamily

  The level indicator in the screenshot does jump around even if nothing is playing. The indicator also reasonably represents sound levels when music is playing. I dont have any mediaservers running or noisy browsertabs open. Also no mic connected. When I turn the volume to max in software and on the amp, there is no noise from the speakers at all. Played music is loud and not distorted. Hardware: Realtek ALC889 over optical audio connector to a generic amp. Software: Debian Wheezy with latest backport kernel 3.14 (same thing on wheezy 3.2 stock), wheezy pulseaudio, xfce session, a custom asound.conf that enables pulseaudio to push sound over optical port. /etc/asound.conf pcm.a52 { @args [CARD] @args.CARD { type string } type rate slave { pcm { type a52 bitrate 448 channels 6 card $CARD } rate 48000 #required somehow, otherwise nothing happens in PulseAudio } }

  Read the article

• XenServer 5.6.1-fp1. Can't get network working

  - by casey_miller

  I have a PC where XenServer 5.6.1 fp-1 has been successfully installed. I've manually set the network settings: 192.168.1.50 255.255.255.0 192.168.1.1 but it's set to xenbr0 iface. While eth0 is empty. When I click on "Configure Management Inteface" it shows that eth0 is connected. But when I ping a default gateway (which is 100% should be accessible) it fails. I used to another shell (Alt+F3) and logged as root. I also failed to ping. with both: ping -I eth0 192.168.1.1 and ping -I xenbr0 192.168.1.1 Be assured that: Cable works Ethernet adapter is 100% functional (prev OS was Ubuntu it was working) There is no firewall rule to deny anything. (everything is allowed) So the question is: What is a problem???

  Read the article

• Little server for a little network: Asus TS Mini + Windows Home Server or other?

  - by microspino

  Hello, I'm building a little network with 4 computer a plotter, 3 printers an a HP Fax/Scan/Copy/Print machine. The network is connected to the web by a D-Link router/firewall. I would like to add little server to have file sharing (reachable via VPN from outside by a single user-road-warrior), automatic backups. I would like to avoid big electrics bills or, to say It in a green way, I would like to avoid useless power consumption made by a big server with hot-plug, Raid, double PSU because I don't need all this stuff. The server must work 24/7 and the budget is between 400€ and 1000€. I'm evaluating the Asus EEE Box (with XP), a TranquilPC (with XP), a FitPC (again with XP), and an Asus TS Mini (with Windows Home Server). I like the latter but since I'm Europe I don't know where I can buy It. Do you have any suggestion/experience to share with me about: which hardware do I have to buy ? which O.S. ?

  Read the article

• How to route traffic from VM (Parallels) over an Open VPN connection on the host (OS X)

  - by withakay

  Scenario: I have a Mac running Lion that is connected to an OpenVPN server I have a Windows XP VM (running on parallels, but I don't think this is important) I want to be able to route traffic from the XP VM via the host Mac's OpenVPN connection so that I can log on to a domain. The remote network is 172.16.0.0/23 (255.255.254.0) Open VPN is configured to supply address in the 10.100.101.0/24 range and sets up the routing to 172.16.0.0 using the gateway 10.100.101.1/32 My local network is 192.16.1.0/24 NOTE: I do not want to install OpenVPN into the XP virtual machine as I would have to use a passwordless key in order for OpenVPN to connect before logon. Anyone got any ideas?

  Read the article

• Is it possible to kill a RAS connection which won't disconnect.

  - by sgmoore

  I have a Windows 2003 Server which has a number or RAS Connections to some of our customers. Occasionally the connections go into a mode where there are connected, but not working. Disconnecting and reconnecting solves the problem. However sometimes you can not disconnect as I get the following error message It is not possible to disconnect at this time. The connection is currently busy with a connect or disconnect operation. There are no visible connection dialog boxes when this message occurs and I usually end up having to restart the server which obviously affects all the other users. I know that if you have a service that is stuck 'stopping' you can just kill it. Is there anything similar that you can do to reset a ras connection?

  Read the article

• Access device with local ip over internet

  - by Joe Perrin

  I apologize up front if this is the wrong place to post this question. It seemed like the best fit. I have a device which is connected to my local network which has an IP of 192.168.1.10 from my router. Additionally I use a Windows 7 machine that runs some software called DirectUpdate which allows me to resolve the local IP of the Windows 7 machine (192.168.1.5) to be accessible to the internet via my domain (example.com) - Basic dynamic DNS updating. I'd like to access the device from example.com. I am unsure how to do this as I don't have any way to install DirectUpdate (or any software) on the device to make the device available to the internet. Any insight here would be appreciated. Thank you.

  Read the article

• Monitor status while using VNC

  - by kumar

  So after connecting to a vnc server via vnc viewer to my desktop (remotely), Is it possible to know whether the monitor connected to the CPU is switched ON or not. Simply put, from command prompt how do you know whether monitor is ON/OFF from command line. Here, Basically I am bit worried about privacy as my monitor can be viewed by anyone while accessed remotely. Any solution? Obviously there is a option to switch off the monitor while starting the vnc server at remote side but I am looking for a better solution to control monitor(possible??) remotely. Thanks!

  Read the article

• Keyboard not responding during boot

  - by Peri

  My keyboard just stopped responding during boot. So I cannot go to BIOS or select system which I want to start. It is USB keyboard and it was working before. I borrowed PS2 keyboard and it also isn't working during boot. Lately I have been having problems with hard disk. Once every 2-5 minutes LED was on for 30 seconds and win7 wasn't responsive. I connected disk to another controller on motherboard and seems it is working now. All that suggests that to me that that motherboard is broken. What can I check? Or maybe you have some other suggestions?

  Read the article

• Routing between two subnets. (Need Solution)

  - by rehanplus

  Need help according to scenario given: Client end PCs: 400 + Network : Server 1 (Linux) : 192.168.2.0/24 (For Application, Internet not working) GW: 192.168.2.1 Clients: 192.168.2.1 - 254 Server 2 (Linux) : 192.168.3.0/24 (For Internet users) GW: 192.168.3.1 Clients: 192.168.3.2 - 254 Server 2 is connected to DSL Broadband. Server 1 and Server 2 both are on same physical network i.e. Same switches. Current issue: i have to deploy a file and print server but this server will be accessed by both (192.168.2.x and 192.168.3.x) one same workgroup. as both subnets are on same switched network. Limitations: Currently there is no hardware routers and firewall. Need to complete this task with Linux / Windows / AD. Tested / Worked so far: Configured one PC with two NIC's With the IPS: NIC 1 : 192.168.3.2 GW: 192.168.3.1 Subnet: 255.255.255.0 NIC 2 : 192.168.2.2 GW: Empty Subnet: 255.255.255.0 Kindly provide any solution what should i do to get sharing enable on both Subnets. Thank you All

  Read the article

• Cannot resolve a single A Record from client machine

  - by Alex

  I set up a simple Bind server on my VPS and it is working properly. The problem occurs with my local windows machines, which are connected to internet through the home router. I created an A-record named 'dev' and it is invisible from my local network for some reason, though people from other locations can resolve dev.mydomain.com. Ironically, dev.mydomain.com cannot be resolved for myself only. If I add another A-record, say, 'gamma' then it becomes visible from my local windows machines instantly. So this is just for that particular 'dev' name. The only difference is that I had dev.mydomain.com server on another IP but that was a month ago; all nameservers have been changed since then. I tried to reboot my router and flushed dns cache on windows machines: no result. Thank you in advance.

  Read the article

• Esxi with iSCSI SAN slows down with many multiple VMs running

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas). Those two machines are connected to each other with Gigabit ethernet, and a procurve switch in between. After a while, if I have many(4-5 or more) vms running, they start to get un-responsive (long delays before anything happens). We are trying to find the reason behind this. Today we looked at esxtop, and found that DAVG of that iSCSI LUN stays at 70-80. I read that +30 is critical! What could be causing those high response-times?

  Read the article

• Strange RDP / Remote Desktop problem

  - by John Landheer

  I'll try to be as specific as I can be: Server is running SBS 2008 R2 (with all updates) Server is connected to the internet Server has 2 NIC's, one is disabled Server is running RDP Service (accessible directly from the internet, I know, not as secure as it should be) Computers A and B are on the same local net. Computers A and B are both Windows 7. Users X and Y are both admins on the server Computer A can connect as user X to the server with mstsc Computer A can connect as user Y to the server with mstsc Computer B can connect as user X to the server with mstsc computer B CANNOT connect as user Y to the server with mstsc! The last point is the problem, I get an authentication error. This used to work flawlessly for the last year. The server and desktops have been rebooted. I find it very strange....

  Read the article

• Add a server between router and switch (production)

  - by Kossel

  I have a small office network basically like below, there are more router/pc connected in S1. As you can see, the router is doing job of DHCP, DNS. but now I wish to add a Linux server between R1 and S1, So I can monitor the network traffic and do other more advance server admin stuff. the whole office network is 192.168.1.x and people are using their computer everyday. What network configuration should the new Linux server have (both interfaces) in order to minimize the changes need in the network? tried to change R1 ip to 192.168.100.1 them add the server with FE0/0 192.168.100.1 and FE0/1 192.168.1.1 but looks cannot ping the original Router..

  Read the article

• wireless dropping out

  - by Sam

  My wireless network connection is dropping out and its driving me nuts. It is weird because it happens at totally random intervals and other devices work while my computer has been dropped. Both my USB dongle and wifi card randomly disconnect from the router and I am unable to connect for a couple of minutes. It is especially irritating because two different adapters are failing at the same time, sounds like a software problem to me, but where? Both my laptop and iPod remain connected when the connection drops. What on earth is happening? I doubt its the router because the other devices would disconnect as well.

  Read the article

• Mac OS X desktop background gets reset to "Andromeda Galaxy.jpg" when users log out

  - by smokris

  I'm running Mac OS 10.6 server, and have a set of 10.6 and 10.7 workstations connected to it for authentication and MCX. Users have network profiles (home folder stored on server, via AFP). When users are logged in, they can change their desktop background. So far so good. However, the next time they log in, their desktop background has been reset to "Andromeda Galaxy.jpg". Though MCX is enabled and used to control other settings, MCX is disabled for the Desktop. What is keeping the users' desktop background from being preserved? How can I fix it?

  Read the article

• SQL connection is too slow

  - by user66905

  We have a business web application in ASP.NET + SQL Server 2008. In the beginning, SQL Server and IIS were on the same machine. Now we bought another machine. Current configuration is IIS machine plus SQL Server machine, and they are connected by a 1gb LAN connection. With this configuration our web application is slower than before. Max bandwidth is 1-2% of network, about 15mbps. When we use another threads to the same SQL Server from the same IIS machine, network use is higher. So this is no problem with SQL Server. Ho we can make higher bandwidth for this SQL connection? Specs: .Net 3.5 SQL Server 2008 Standard file transfer can use 100% of LAN SQL connection by TCP/IP protocol SQL logins Pool tested with enable and

  Read the article

• Bind dns server in Solaris 10 and win xp clients

  - by stevecomptech

  Hi, Added this in zone db file, i am running solaris 10 _ldap._tcp.mydomain.com. SRV 0 0 389 dc.mydomain.com. _kerberos._tcp.mydomain.com. SRV 0 0 88 dc.mydomain.com. _ldap._tcp.dc._msdcs.mydomain.com. SRV 0 0 389 dc.mydomain.com. _kerberos._tcp.dc._msdcs.mydomain.com. SRV 0 0 88 host.mydomain.com. Now i get this error when i try to join win xp to the domain The query was for the SRV record for _ldap._tcp.dc._msdcs.mydomain.com The following domain controllers were identified by the query: host.mydomain.com Common causes of this error include: Host (A) records that map the name of the domain controller to its IP addresses are missing or contain incorrect addresses. Domain controllers registered in DNS are not connected to the network or are not running. What do i need to change in order my win xp join the domain

  Read the article

• Filemaker Server Not Installing and Windows Problems

  - by Shelly

  When I tried installing Filemaker Server 8.0 on Windows 2003 Server Standard Edition R2, an error message pop up that states: MMC has detected an error in a snap-in. It is recommended that you shut down and restart MMC. After this message pops up, Filemaker Server freezes. I'm also having problems with openssl and running executable files, but am not sure if the 2 are related. Error message for openssl states: Openssl.exe encountered a problem and needed to close. In one of the computers connected to the network running this same Server 2003 R2, when I tried double-clicking on Dr. Web antivirus to do a scan, nothing happens. I have done this many times before reinstalling the server, and it never gave trouble before this. Any help given is appreciated.

  Read the article

< Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >