Search Results

Search found 9608 results on 385 pages for 'flash drives'.

Page 174/385 | < Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >

• How can I set up FakeRAID/SoftRAID using mdadm without losing data?

  - by Danatela

  There is RAID0 of 2 drives connected through Silicon Image 3132 SATA SoftRAID controller. Under Windows it was partitioned as one dynamic GPT-disk having 4 TB NTFS volume. There is a lot of music and movies on the drive. I'm trying to get him to be seen under Ubuntu as a single disk, not as 2 by 2 terabytes. I tried to read it through dmraid, had no success, it is not displayed in /dev/mapper. Also tried to configure the kernel, but did not find anything suspicious, the driver for my controller was on. There is also a driver from the manufacturer, but it is only available for RHEL and SLES. Here it's reported that SoftRAID is supported by the kernel, but apparently not completely. If I thrust drives in the AMD controller, built into the motherboard, the drive is seen as a single, but the data is lost. I know about mdadm that it is able to ditch all the information on the disks. So, is it possible to somehow create an array without actually recording information on used drives and to make the system correctly identify sections on it later? Information about the array: /dev/sdf - Disk 0 /dev/sdg - Disk 1 Array type: Stripe Block Size: 64KB Also, a device /dev/md1 is created using command mknod /dev/md1 b 9 1

  Read the article

• How to re-add RAID-10 dropped drive?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• Start frei für die Exadata Community im neuen Look!

  - by Frank Schneede (Exadata Community)

  Endlich ist es soweit! Pünktlich mit dem Start der DOAG Konferenz 2012, die vom 20.11. - 22.11.2012 in Nürnberg stattfindet, geht die Deutsche Exadata Community in völlig neu gestaltetem Outfit an den Start. Sie werden hier regelmäßig über neue Ankündigungen sowie Tipps und Tricks im Umgang mit Exadata informiert. Durch das freiere Blogformat werden an dieser Stelle auch Berichte über Exadata Projekte erscheinen, die besonders hervorhebenswert sind. Ich denke, Sie dürfen gespannt sein! Vieles hat sich seit dem letzten Update in der Community getan, denn auf der diesjährigen Oracle Open World in San Franzisco wurde eine ganze Reihe spannender Ankündigungen rund um Exadata gemacht. Die kürzlich vorgestellten Modelle Exadata Database Machine X3-2 und X3-8 sind in der grundlegenden Architektur zwar unverändert geblieben, jedoch sind die Modelle mit aktuellen Prozessoren in SandyBridge Mikroprozessorarchitektur noch leistungsfähiger als bisher. Der vierfach vergrößerte Flash Cache nimmt wesentlich mehr Daten auf und macht die Exadata so zur "In-Memory" Database Machine. Mit der neuen Exadata Software 11.2.3.2 kann der Flash Cache nun als persistenter Write Back Flash Cache verwendet werden. Durch das neuartige Caching profitieren auch OLTP Applikationen, die eine hohe Last von schreibenden Transaktionen verursachen, stärker von der Exadata Technologie. Ein neues Einstiegsmodell, das Exadata X3-2 Eighth Rack, vervollständigt die Produktfamilie und senkt abermals die Einstiegshürde für die Kunden.  Die beiden Community Tipps zur Exadata Hardware wurden aktualisiert. Lesen Sie alles über die Exadata Database Machine X3-2 und deren große Schwester, die Exadata Database Machine X3-8.

  Read the article

• SDcardReader/Writer is not connected

  - by Insuk

  My IOGEAR sdCardReader/Writer is recongized on Ubutu(by using VM ware) but when I tried to connect to "Removable Devices - Alcor Micro Flash Card Reader/Writer" , the follwoing message is appeared. " The connection for the USB device "Alcor Micro Flash Card Reader/Writer" was unsuccessful. The device is currently in use. " But I think it is not used. Should I use IOGEAR driver for this one? When I connect the card reader, Ubuntu automatically got the "Alcor Micro Flash Card Reader/Writer" . How can I fix the problem? Thank you, Insuk the result of lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0b95:7720 ASIX Electronics Corp. AX88772 Bus 002 Device 002: ID 0e0f:0003 VMware, Inc. Virtual Mouse Bus 002 Device 003: ID 0e0f:0002 VMware, Inc. Virtual USB Hub Bus 002 Device 004: ID 0e0f:0008 VMware, Inc. Bus 002 Device 005: ID 0403:bcda Future Technology Devices International, Ltd From the vmware log : 2013-10-18T09:00:07.494-06:00| vmx| I120: USB-CCID: Could not establish context: SCARD_E_NO_SERVICE(0x8010001d). 2013-10-18T09:00:07.494-06:00| vmx| I120: USB-CCID: Could not establish context: SCARD_E_NO_SERVICE(0x8010001d).

  Read the article

• why doesn't my computer resume after sleeping overnight?

  - by bamdad

  i'm having a weird, weird bug that's been haunting me since 11.10. if i listen to music or watch a video and my computer automatically goes to sleep at night, it won't properly resume in the morning. otherwise, suspend and resume works just fine. what happens is that the wi-fi and bluetooth indicator (that turns from white to orange when suspending) stays orange, the display doesn't turn on, and the only option i have is to hard reset the machine. here's what i've tried so far: installing (and uninstalling and reinstalling) laptop-mode-tools switching the proprietary wireless driver (broadcom-wl) to the open source one (brcmsmac & bcma) and back unloading (and blacklisting) all bluetooth modules (rfcomm, btusb, bnep, bluetooth) and stopping (# stop bluetooth) and disabling (# echo 'manual' /etc/init/bluetooth.override) the bluetooth service creating a custom pm sleep action as suggested here: http://ubuntuforums.org/showthread.php?p=11926504 not watching youtube / any stuff that uses flash before going to sleep (i have flashblock, and i checked $ ps aux | grep flash) because i suspected flash to be the culprit trying out different versions of fglrx (the one from the repos, then installing the latest one from amd's site via generated .deb files, then back to the official ones) none of these worked. i remember back in the days of 10.04, there was a gconf key called network sleep: i thought about disabling that, since re-enabling the wireless card seems to be the problem (according to the indicator led), but the option appears to be missing from gnome 3 (unity-2d, whatever). does anyone have any ideas? thanks, bamdad

  Read the article

• Why can't I boot from portable HD?

  - by user11239

  I've been trying to get Ubuntu 10.04-LTS 32-bit desktop installed onto a 250GB FreeAgent Go drive from Seagate. I've been able to install onto a USB flash drive and boot successfully from this. I have installed Ubuntu onto the jump drive using Universal USB Installer, and this was a total success in terms of getting Ubuntu to run off a flash drive. I was unable to accomplish this with the portable HDD. I then, following instructions, attempted to install the OS onto the HDD once booted up from the flash drive. After installing the OS on the HDD, the computer would simply not load the OS when the HDD medium was selected for booting from. However, as there is no System-> Preferences-> Removable Drives and Media I could not complete this step. Is this vital? How do I do this under Ubuntu 10.04? I have formmated the MBR on the HDD and repeated the above, still with no success. I have also browsed some forums that mention there may be something related to spin-up speeds, but nothing explained in detail the issue or how to solve it, and I'm not familiar enough with system booting to understand if this could be an issue. Basically, what I'm trying to do is get Ubuntu to boot off the HDD, I've attempted several things, and the result is, after selecting the HDD from BIOS, the OS never starts booting (after waiting upwards of ten minutes). I just have a white cursor blinking. I can always get it to boot from the jump drive. Related question

  Read the article

• Hard time installing Ubuntu

  - by Nick

  I have a MSI GT780DXR that currently is booting windows 7. I've been trying to dual boot windows 7 and ubuntu for some time now. Here's specs that I think would make a difference Windows 7 500GB*2 RAID 0 hard drives. (Hardware RAID I'm not sure if it's a dedicated RAID card though) 7200RPM Nvidia GT570M Background: I tried to install 12.04 (64 bit) a few times but the Desktop live cd and pendrive boots with a black screen. I've tried wubi but it boots to a black screen as well. I then tried the alternative 12.04 (64 bit) and went through the installation all the way til partitioning. I let Ubuntu notice the raid setup and I setup my swap, /, and home drives, I used my free space to create the three partitions. I tried to resize the windows drive and it told me I couldn't and to be happy with my current setup. When I finally got past I got an error on installing GRUB 2 and decided to skip it and continued on to finish installation. When I tried to boot up I got an invalid partition table error. Windows recovery disc, and a GPARTED live cd couldn't find any hard drives. I ended up following advice and typed this into the recovery command prompt. bootrec /fixmbr bootrec /fixboot bootrec /rebuildBcd It worked and here I am now. The question is, how would I be able to dual boot windows 7 and Ubuntu 12.04 with this information? Thanks,

  Read the article

• cannot boot ubuntu 13.10 with my usb, Can i change the kernal on my laptop to run it?

  - by Carlos Dunick

  Currently i am running 12.04 and looking for an upgrade to 13.10 I first tried a bootable 64bit usb and failed. With the message saying "Kernal requires an x86-64 CPU but only detected an I686 CPU Unable to boot please use a kernal appropriate for your CPU" then tried 32bit and same message came up. Is this due to my laptop simply being to slow? or can/should i change the kernal somehow? Acer Aspire 5710z Intel Pentium dual core processor, 1.73Ghz, 533 MHz FSB, 1 MB L2 cache. 2GB DDR2 lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) 00:1c.2 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02) 04:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02) 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 06:00.0 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller 06:00.1 SD Host controller: ENE Technology Inc ENE PCI SmartMedia / xD Card Reader Controller 06:00.2 FLASH memory: ENE Technology Inc Memory Stick Card Reader Controller 06:00.3 FLASH memory: ENE Technology Inc ENE PCI Secure Digital / MMC Card Reader Controller

  Read the article

• Why is my HDD going back from standy?

  - by Pablo

  My hard drives, connected to Ubuntu server are producing the following log every exactly 5 minutes. Nov 1 14:10:50 localhost kernel: [ 1602.884936] ata2.00: hard resetting link Nov 1 14:10:51 localhost kernel: [ 1603.226804] ata2.01: hard resetting link Nov 1 14:10:52 localhost kernel: [ 1604.274533] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Nov 1 14:10:52 localhost kernel: [ 1604.274548] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Nov 1 14:10:52 localhost kernel: [ 1604.356669] ata2.00: configured for UDMA/133 Nov 1 14:10:52 localhost kernel: [ 1604.375247] ata2.01: configured for UDMA/133 Nov 1 14:10:52 localhost kernel: [ 1604.375265] ata2: EH complete I don't think this is related to hard drive failure, because it happens for ALL hard drives connected and ONLY when I write spindown_time = 12 in /etc/hdparm.conf. The reason I add this value is to put disks into standby mode after 60 seconds, which is happening after that period (checked with hdparm -C). The first clue I thought that smartd was running and spinning the drive. However, I couldn't find it in ps -aux | grep smart. Additionally, iostat does show that nobody accessed those drives, since Blk_read, Blk_wrtn remain unchanged. I also killed all processes that may be doing something with hdd(eg SAMBA). So I guess the problem is solely with hdparm... I have no more clue where that 5 minute value hides.

  Read the article

• how do I fix 12.04 which has crashed after the latest update

  - by user70261

  I added a new drive to my system because the old one was full and stopped. I installed 12.04 at the same time, onto the new drive using a flash disk while off line. The system performs fine on 12.04 from the flash disk and it booted from the new drive OK and I was able to recover all my old data. The updater suggested that I update, so I went ahead and did so. At the end of which it wanted to reboot. I went ahead but on reboot I get to the log in prompt and then the whole system crashes. It tries to recover and then performs a bug report during which it tells me that a whole bunch of files are out of date (these would be the new ones I just updated!) and the screen goes black. Game over. I've tried to reboot several times ... same result. I can boot off the flash drive OK. How do I restore the system I had before the update, without over writing all my hard earned recovered data? Or how do I identify the "new updates" that are causing me grief?

  Read the article

• 2012?7?14???My Oracle Support

  - by user763198

  Normal 0 7.8 ? 0 2 false false false EN-US ZH-CN X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:????; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} ?2012?7?14?,??????My Oracle Support? ?????????????????????????????,????????Flash? ????????My Oracle Support Mobile?????????????????????,????????????? ????? ????????,2012?7?14???12:00??,??My Oracle Support ???????5??????????????????????????????????????,??????? Oracle ????? ???????? ????????? My Oracle Support HTML ????,????Flash????????HTML?????????: Oracle Configuration Manager Patch ?? On Demand ?CRM On Demand ?????????? ? ????????? ??????Flash???,????????????????,My Oracle Support?HTML????????Internet Explorer6(IE6)?????,???? Article ID 1453756.1 ???????,?????????? My Oracle Support Mobile ??????,??????? My Oracle Support Mobile ?????,???: ????????bugs ???? (RFCs) (??On Demand ??) ??????(???????) ? ?????????,????? My Oracle Support Article ID 1453756.1 ????????????,???? My Oracle Support?????? “Contact Us” ????????????? ???? ?????

  Read the article

• Club Platinum 2010 ??! ~???:???????~

  - by Urakawa

  ?????Platinum Club??????????Platinum Club???ORACLE MASTER Platinum??????????????????????????????????????Platinum Club?????????????Club Platinum?(????????)????5?19??????????!   ??????Oracle Database?????????????????????????? ?????????? ?????????? ?????? ?? ???????????Platinum????????????????????????? ???????????????????3?????????(?????????? ?? ????? ????? ?????????????!)????Oracle?????! DB????????Oracle Database/Exadata ??7???????????3???????!?????????????????????????????? ???????Oracle Database 11g R2?????????ASM????????????(ACFS)???RAC One Node??????????????????????????USB???????????ACFS???????????!????????!????????!?????????????????????   ???????Oracle Exadata??Exadata Smart Flash Cache???Data Loading?????US?Oracle Corporation???????????????????????Smart Flash Cache??????DB?Flash Cache?????Data Loading????????????????????????????????????!??Tips???!?????????????????????????????????????????????????Oracle??????????????????????????!Oracle?????? Inside the Oracle Optimizer Kevin Closson's Oracle Blog   ???????????Oracle Exadata??Exadata Smart Scan???Exadata Hybrid Columnar Compression?????????????????????????????????????????????????????????????????????·?????????????IT?????????????????????????????????????????????????Oracle Database 11g: Real-Time SQL Monitoring?SQL Monitor active report?????????????!?????????   ????????!???????????????!????????????????????Platinum Club????????????????????????????Oracle Exadata??????????????????????????????????????????????????????m(_ _)m?????? Oracle Database 11g R2 ??????(PDF) (Platinum Club????)   ???????ORACLE MASTER??????????ORACLE MASTER?????????????????? ??????? ?????????????????ORACLE MASTER???update????????????Oracle Exadata?????????????!?Oracle Database 11g???????????????ORACLE MASTER Expert????Oracle E-Business Suite???DBA??????????????????????????????????????????Blog????????????????????????????   ????1????????????????????????????????Platinum of the Year????!~???~

  Read the article

• Animating gradient displays line artifacts in ActionScript

  - by TheDarkIn1978

  i've programatically created a simple gradient (blue to red) sprite rect using my own basic class called GradientRect, but moving or animation the sprite exhibits line artifacts. when the sprite is rotating, it kind of resembles bad reception of an old television set. i'm almost certain the cause is because each line slice of the gradient is vector so there are gaps between the lines - this is visible when the sprite is zoomed in. var colorPickerRect:GradientRect = new GradientRect(200, 200, 0x0000FF, 0xFF0000); addChild(colorPickerRect); colorPickerRect.cacheAsBitmap = true; colorPickerRect.x = colorPickerRect.y = 100; colorPickerRect.addEventListener(Event.ENTER_FRAME, rotate); function rotate(evt:Event):void { evt.target.rotation += 1; } ________________________ //CLASS PACKAGE package { import flash.display.CapsStyle; import flash.display.GradientType; import flash.display.LineScaleMode; import flash.display.Sprite; import flash.geom.Matrix; public class GradientRect extends Sprite { public function GradientRect(gradientRectWidth:Number, gradientRectHeight:Number, ...leftToRightColors) { init(gradientRectWidth, gradientRectHeight, leftToRightColors); } private function init(gradientRectWidth:Number, gradientRectHeight:Number, leftToRightColors:Array):void { var leftToRightAlphas:Array = new Array(); var leftToRightRatios:Array = new Array(); var leftToRightPartition:Number = 255 / (leftToRightColors.length - 1); var pixelColor:Number; var i:int; //Push arrays for (i = 0; i < leftToRightColors.length; i++) { leftToRightAlphas.push(1); leftToRightRatios.push(i * leftToRightPartition); } //Graphics matrix and lineStyle var leftToRightColorsMatrix:Matrix = new Matrix(); leftToRightColorsMatrix.createGradientBox(gradientRectWidth, 1); graphics.lineStyle(1, 0, 1, false, LineScaleMode.NONE, CapsStyle.NONE); for (i = 0; i < gradientRectWidth; i++) { graphics.lineGradientStyle(GradientType.LINEAR, leftToRightColors, leftToRightAlphas, leftToRightRatios, leftToRightColorsMatrix); graphics.moveTo(i, 0); graphics.lineTo(i, gradientRectHeight); } } } } how can i solve this problem?

  Read the article

• Error in playing a swf file on internet explorer

  - by Rajeev

  In the below code i get an error saying Error #2007: Parameter url must be non-null on Ineternet explorer only.What am i doing wrong here html <OBJECT classid="clsid:D27CDB6E-AE6D-11cf-96B8-444553540000" WIDTH="50" HEIGHT="50" id="myMovieName"> <PARAM NAME="movie" VALUE="/media/players/testsound.swf" /> <PARAM NAME="quality" VALUE="high" /> <PARAM NAME="bgcolor" VALUE="#FFFFFF" /> <EMBED href="/media/players/testsound.swf" src="/media/players/testsound.swf" flashvars="soundUrl=sound.mp3" quality=high bgcolor=#FFFFFF NAME="myMovieName" ALIGN="" TYPE="application/x-shockwave-flash"> </EMBED> </OBJECT> mxml ; import flash.net.; import mx.controls.Alert; import mx.controls.Button; import flash.events.Event; import flash.media.Sound; import flash.net.URLRequest; private function clickhandler(event:Event):void { var musicfile:String; var s:Sound = new Sound(); s.addEventListener(Event.COMPLETE, onSoundLoaded); var req:URLRequest = new URLRequest("/opt/cloodon/site/media/players/sound.mp3"); //musicfile = stage.loaderInfo.parameters["soundUrl"]; //var req:URLRequest = new URLRequest(musicfile); s.load(req); } private function onSoundLoaded(event:Event):void { //Alert.show("1"); //var localSound:Sound = event.currentTarget as Sound; var localSound:Sound = event.target as Sound; localSound.play(); } ]]> </fx:Script> <fx:Declarations> <!-- Place non-visual elements (e.g., services, value objects) here --> </fx:Declarations> <!--<mx:Button id="play" label="PLAY" click="clickhandler(event)" />--> <mx:Image id="loader1" source="@Embed(source='/opt/cloodon/site/media/img/speaker.gif')" click="clickhandler(event)" /> </s:Application>

  Read the article

• Stubbing a before_filter with RSpec

  - by TheDelChop

  Guys, I'm having trouble understanding why I can't seem to stub this controller method :load_user, since all of my tests fail if I change the actual implementation of :load_user to not return and instance of @user. Can anybody see why my stub (controller.stub!(:load_user).and_return(@user)) seems to fail to actually get called when RSpec makes a request to the controller? require 'spec_helper' describe TasksController do before(:each) do @user = Factory(:user) sign_in @user @task = Factory(:task) User.stub_chain(:where, :first).and_return(@user) controller.stub!(:load_user).and_return(@user) end #GET Index describe "GET Index" do before(:each) do @tasks = 7.times{Factory(:task, :user = @user)} @user.stub!(:tasks).and_return(@tasks) end it "should should find all of the tasks owned by a user" do @user.should_receive(:tasks).and_return(@tasks) get :index, :user_id = @user.id end it "should assign all of the user's tasks to the view" do get :index, :user_id = @user.id assigns[:tasks].should be(@tasks) end end #GET New describe "GET New" do before(:each) do @user.stub_chain(:tasks, :new).and_return(@task) end it "should return a new Task" do @user.tasks.should_receive(:new).and_return(@task) get :new, :user_id = @user.id end end #POST Create describe "POST Create" do before(:each) do @user.stub_chain(:tasks, :new).and_return(@task) end it "should create a new task" do @user.tasks.should_receive(:new).and_return(@task) post :create, :user_id = @user.id, :task = @task.to_s end it "saves the task" do @task.should_receive(:save) post :create, :user_id = @user.id, :task = @task end context "when the task is saved successfully" do before(:each) do @task.stub!(:save).and_return(true) end it "should set the flash[:notice] message to 'Task Added Successfully'"do post :create, :user_id = @user.id, :task = @task flash[:notice].should == "Task Added Successfully!" end it "should redirect to the user's task page" do post :create, :user_id = @user.id, :task = @task response.should redirect_to(user_tasks_path(@user.id)) end end context "when the task isn't saved successfully" do before(:each) do @task.stub(:save).and_return(false) end it "should return to the 'Create New Task' page do" do post :create, :user_id = @user.id, :task = @task response.should render_template('new') end end end it "should attempt to authenticate and load the user who owns the tasks" do context "when the tasks belong to the currently logged in user" do it "should set the user instance variable to the currently logged in user" do pending end end context "when the tasks belong to another user" do it "should set the flash[:notice] to 'Sorry but you can't view other people's tasks.'" do pending end it "should redirect to the home page" do pending end end end end class TasksController < ApplicationController before_filter :load_user def index @tasks = @user.tasks end def new @task = @user.tasks.new end def create @task = @user.tasks.new if @task.save flash[:notice] = "Task Added Successfully!" redirect_to user_tasks_path(@user.id) else render :action => 'new' end end private def load_user if current_user.id == params[:user_id].to_i @user = User.where(:id => params[:user_id]).first else flash[:notice] = "Sorry but you can't view other people's tasks." redirect_to root_path end end end Can anybody see why my stub doesnt' work? Like I said, my tests only pass if I make sure that load_user works, if not, all my tests fail which makes my think that RSpec isn't using the stub I created. Thanks, Joe

  Read the article

• A standard event messaging system with AJAX?

  - by Gutzofter

  Is there any standards or messaging framework for AJAX? Right now I have a single page that loads content using Ajax. Because I had a complex form for data entry as part of my content, I need to validate certain events that can occur in my form. So after some adjustments driven by my tests: asyncShould("search customer list click", 3, function() { stop(1000); $('#content').show(); var forCustomerList = newCustomerListRequest(); var forShipAndCharge = newShipAndChargeRequest(forCustomerList); forCustomerList.page = '../../vt/' + forCustomerList.page; forShipAndCharge.page = 'helpers/helper.php'; forShipAndCharge.data = { 'action': 'shipAndCharge', 'DB': '11001' }; var originalComplete = forShipAndCharge.complete; forShipAndCharge.complete = function(xhr, status) { originalComplete(xhr, status); ok($('#customer_edit').is(":visible"), 'Shows customer editor'); $('#search').click(); ok($('#customer_list').is(":visible"), 'Shows customer list'); ok($('#customer_edit').is(":hidden"), 'Does not show customer editor'); start(); }; testController.getContent(forShipAndCharge); }); Here is the controller for getting content: getContent: function (request) { $.ajax({ type: 'GET', url: request.page, dataType: 'json', data: request.data, async: request.async, success: request.success, complete: request.complete }); }, And here is the request event: function newShipAndChargeRequest(serverRequest) { var that = { serverRequest: serverRequest, page: 'nodes/orders/sc.php', data: 'customer_id=-1', complete: errorHandler, success: function(msg) { shipAndChargeHandler(msg); initWhenCustomer(that.serverRequest); }, async: true }; return that; } And here is a success handler: function shipAndChargeHandler(msg) { $('.contentContainer').html(msg.html); if (msg.status == 'flash') { flash(msg.flash); } } And on my server side I end up with a JSON structure that looks like this: $message['status'] = 'success'; $message['data'] = array(); $message['flash'] = ''; $message['html'] = ''; echo json_encode($message); So now loading content consists of two parts: HTML, this is the presentation of the form. DATA, this is any data that needs be loaded for the form FLASH, any validation or server errors STATUS tells client what happened on server. My question is: Is this a valid way to handle event messaging on the client-side or am I going down a path of heartache and pain?

  Read the article

• cannot make ubuntu 64-bit v12.04 install work

  - by honestann

  I decided it was time to update my ubuntu (single boot) computer from 64-bit v10.04 to 64-bit v12.04. Unfortunately, for some reason (or reasons) I just can't make it work. Note that I am attempting a fresh install of 64-bit v12.04 onto a new 3TB hard disk, not an upgrade of the 1TB hard disk that contains my working 64-bit v10.04 installation. To perform the attempted install of v12.04 I unplug the SATA cable from the 1TB drive and plug it into the 3TB drive (to avoid risking damage to my working v10.04 installation). I downloaded the ubuntu 64-bit v12.04 install DVD ISO file (~1.6 GB) from the ubuntu releases webpage and burned it onto a DVD. I have downloaded the DVD ISO file 3 times and burned 3 of these installation DVDs (twice with v10.04 and once with my winxp64 system), but none of them work. I run the "check disk" on the DVDs at the beginning of the installation process to assure the DVD is valid. When installation completes and the system boots the 3TB drive, it reports "unknown filesystem". After installation on the 250GB drives, the system boots up fine. During every install I plug the same SATA cable (sda) into only one disk drive (the 3TB or one of the 250GB drives) and leave the other disk drives unconnected (for simplicity). It is my understanding that 64-bit ubuntu (and 64-bit linux in general) has no problem with 3TB disk drives. In the BIOS I have tried having EFI set to "enabled" and "auto" with no apparent difference (no success). I never bothered setting the BIOS to "non-EFI". I have tried partitioning the drive in a few ways to see if that makes a difference, but so far it has not mattered. Typically I manually create partitions something like this: 8GB /boot ext4 8GB swap 3TB / ext4 But I've also tried the following, just in case it matters: 8GB boot efi 8GB swap 8GB /boot ext4 3TB / ext4 Note: In the partition dialog I specify bootup on the same drive I am partitioning and installing ubuntu v12.04 onto. It is a VERY DANGEROUS FACT that the default for this always comes up with the wrong drive (some other drive, generally the external drive). Unless I'm stupid or misunderstanding something, this is very wrong and very dangerous default behavior. Note: If I connect the SATA cable to the 1TB drive that has been my ubuntu 64-bit v10.04 system drive for the past 2 years, it boots up and runs fine. I guess there must be a log file somewhere, and maybe it gives some hints as to what the problem is. I should be able to boot off the 1TB drive with the 3TB drive connected as a secondary (non-boot) drive and get the log file, assuming there is one and someone tells me the name (and where to find it if the name is very generic). After installation on the 3TB drive completes and the system reboots, the following prints out on a black screen: Loading Operating System ... Boot from CD/DVD : Boot from CD/DVD : error: unknown filesystem grub rescue> Note: I have two DVD burners in the system, hence the duplicate line above. Note: I install and boot 64-bit ubuntu v12.04 on both of my 250GB in this same system, but still cannot make the 3TB drive boot. Sigh. Any ideas? ========== motherboard == gigabyte 990FXA-UD7 CPU == AMD FX-8150 8-core bulldozer @ 3.6 GHz RAM == 8GB of DDR3 in 2 sticks (matched pair) HDD == seagate 3TB SATA3 @ 7200 rpm (new install 64-bit v12.04 FAILS) HDD == seagate 1TB SATA3 @ 7200 rpm (64-bit v10.04 WORKS for two years) HDD == seagate 250GB SATA2 @ 7200 rpm (new install 64-bit v12.04 WORKS) HDD == seagate 250GB SATA2 @ 7200 rpm (new install 64-bit v12.04 WORKS) GPU == nvidia GTX-285 ??? == no overclocking or other funky business USB == external seagate 2TB HDD for making backups DVD == one bluray burner (SATA) DVD == one DVD burner (SATA) 64-bit ubuntu v10.04 has booted and run fine on the seagate 1TB drive for 2 years.

  Read the article

• Ask the Readers: Backing Your Files Up – Local Storage versus the Cloud

  - by Asian Angel

  Backing up important files is something that all of us should do on a regular basis, but may not have given as much thought to as we should. This week we would like to know if you use local storage, cloud storage, or a combination of both to back your files up. Photo by camknows. For some people local storage media may be the most convenient and/or affordable way to back up their files. Having those files stored on media under your control can also provide a sense of security and peace of mind. But storing your files locally may also have drawbacks if something happens to your storage media. So how do you know whether the benefits outweigh the disadvantages or not? Here are some possible pros and cons that may affect your decision to use local storage to back up your files: Local Storage Pros You are in control of your data Your files are portable and can go with you when needed if using external or flash drives Files are accessible without an internet connection You can easily add more storage capacity as needed (additional drives, etc.) Cons You need to arrange room for your storage media (if you have multiple externals drives, etc.) Possible hardware failure No access to your files if you forget to bring your storage media with you or it is too bulky to bring along Theft and/or loss of home with all contents due to circumstances like fire If you are someone who is always on the go and needs to travel as lightly as possible, cloud storage may be the perfect way for you to back up and access your files. Perhaps your laptop has a hard-drive failure or gets stolen…unhappy events to be sure, but you will still have a copy of your files available. Perhaps a company wants to make sure their records, files, and other information are backed up off site in case of a major hardware or system failure…expensive and/or frustrating to fix if it happens, but once again there is a nice backup ready to go once things are fixed. As with local storage, here are some possible pros and cons that may influence your choice of cloud storage to back up your files: Cloud Storage Pros No need to carry around flash or bulky external drives All of your files are accessible wherever there is an internet connection No need to deal with local storage media (or its’ upkeep) Your files are still safe if your home is broken into or other unfortunate circumstances occur Cons Your files and data are not 100% under your control Possible hardware failure or loss of files on the part of your cloud storage provider (this could include a disgruntled employee wreaking havoc) No access to your files if you do not have an internet connection The cloud storage provider may eventually shutdown due to financial hardship or other unforeseen circumstances The possibility of your files and data being stolen by hackers due to a security breach on the part of your cloud storage provider You may also prefer to try and cover all of the possibilities by using both local and cloud storage to back up your files. If something happens to one, you always have the other to fall back on. Need access to those files at or away from home? As long as you have access to either your storage media or an internet connection, you are good to go. Maybe you are getting ready to choose a backup solution but are not sure which one would work better for you. Here is your chance to ask your fellow HTG readers which one they would recommend. Got a great backup solution already in place? Then be sure to share it with your fellow readers! How-To Geek Polls require Javascript. Please Click Here to View the Poll. Latest Features How-To Geek ETC The 20 Best How-To Geek Explainer Topics for 2010 How to Disable Caps Lock Key in Windows 7 or Vista How to Use the Avira Rescue CD to Clean Your Infected PC The Complete List of iPad Tips, Tricks, and Tutorials Is Your Desktop Printer More Expensive Than Printing Services? 20 OS X Keyboard Shortcuts You Might Not Know Winter Sunset by a Mountain Stream Wallpaper Add Sleek Style to Your Desktop with the Aston Martin Theme for Windows 7 Awesome WebGL Demo – Flight of the Navigator from Mozilla Sunrise on the Alien Desert Planet Wallpaper Add Falling Snow to Webpages with the Snowfall Extension for Opera [Browser Fun] Automatically Keep Up With the Latest Releases from Mozilla Labs in Firefox 4.0

  Read the article

• Oracle TimesTen In-Memory Database Performance on SPARC T4-2

  - by Brian

  The Oracle TimesTen In-Memory Database is optimized to run on Oracle's SPARC T4 processor platforms running Oracle Solaris 11 providing unsurpassed scalability, performance, upgradability, protection of investment and return on investment. The following demonstrate the value of combining Oracle TimesTen In-Memory Database with SPARC T4 servers and Oracle Solaris 11: On a Mobile Call Processing test, the 2-socket SPARC T4-2 server outperforms: Oracle's SPARC Enterprise M4000 server (4 x 2.66 GHz SPARC64 VII+) by 34%. Oracle's SPARC T3-4 (4 x 1.65 GHz SPARC T3) by 2.7x, or 5.4x per processor. Utilizing the TimesTen Performance Throughput Benchmark (TPTBM), the SPARC T4-2 server protects investments with: 2.1x the overall performance of a 4-socket SPARC Enterprise M4000 server in read-only mode and 1.5x the performance in update-only testing. This is 4.2x more performance per processor than the SPARC64 VII+ 2.66 GHz based system. 10x more performance per processor than the SPARC T2+ 1.4 GHz server. 1.6x better performance per processor than the SPARC T3 1.65 GHz based server. In replication testing, the two socket SPARC T4-2 server is over 3x faster than the performance of a four socket SPARC Enterprise T5440 server in both asynchronous replication environment and the highly available 2-Safe replication. This testing emphasizes parallel replication between systems. Performance Landscape Mobile Call Processing Test Performance System Processor Sockets/Cores/Threads Tps SPARC T4-2 SPARC T4, 2.85 GHz 2 16 128 218,400 M4000 SPARC64 VII+, 2.66 GHz 4 16 32 162,900 SPARC T3-4 SPARC T3, 1.65 GHz 4 64 512 80,400 TimesTen Performance Throughput Benchmark (TPTBM) Read-Only System Processor Sockets/Cores/Threads Tps SPARC T3-4 SPARC T3, 1.65 GHz 4 64 512 7.9M SPARC T4-2 SPARC T4, 2.85 GHz 2 16 128 6.5M M4000 SPARC64 VII+, 2.66 GHz 4 16 32 3.1M T5440 SPARC T2+, 1.4 GHz 4 32 256 3.1M TimesTen Performance Throughput Benchmark (TPTBM) Update-Only System Processor Sockets/Cores/Threads Tps SPARC T4-2 SPARC T4, 2.85 GHz 2 16 128 547,800 M4000 SPARC64 VII+, 2.66 GHz 4 16 32 363,800 SPARC T3-4 SPARC T3, 1.65 GHz 4 64 512 240,500 TimesTen Replication Tests System Processor Sockets/Cores/Threads Asynchronous 2-Safe SPARC T4-2 SPARC T4, 2.85 GHz 2 16 128 38,024 13,701 SPARC T5440 SPARC T2+, 1.4 GHz 4 32 256 11,621 4,615 Configuration Summary Hardware Configurations: SPARC T4-2 server 2 x SPARC T4 processors, 2.85 GHz 256 GB memory 1 x 8 Gbs FC Qlogic HBA 1 x 6 Gbs SAS HBA 4 x 300 GB internal disks Sun Storage F5100 Flash Array (40 x 24 GB flash modules) 1 x Sun Fire X4275 server configured as COMSTAR head SPARC T3-4 server 4 x SPARC T3 processors, 1.6 GHz 512 GB memory 1 x 8 Gbs FC Qlogic HBA 8 x 146 GB internal disks 1 x Sun Fire X4275 server configured as COMSTAR head SPARC Enterprise M4000 server 4 x SPARC64 VII+ processors, 2.66 GHz 128 GB memory 1 x 8 Gbs FC Qlogic HBA 1 x 6 Gbs SAS HBA 2 x 146 GB internal disks Sun Storage F5100 Flash Array (40 x 24 GB flash modules) 1 x Sun Fire X4275 server configured as COMSTAR head Software Configuration: Oracle Solaris 11 11/11 Oracle TimesTen 11.2.2.4 Benchmark Descriptions TimesTen Performance Throughput BenchMark (TPTBM) is shipped with TimesTen and measures the total throughput of the system. The workload can test read-only, update-only, delete and insert operations as required. Mobile Call Processing is a customer-based workload for processing calls made by mobile phone subscribers. The workload has a mixture of read-only, update, and insert-only transactions. The peak throughput performance is measured from multiple concurrent processes executing the transactions until a peak performance is reached via saturation of the available resources. Parallel Replication tests using both asynchronous and 2-Safe replication methods. For asynchronous replication, transactions are processed in batches to maximize the throughput capabilities of the replication server and network. In 2-Safe replication, also known as no data-loss or high availability, transactions are replicated between servers immediately emphasizing low latency. For both environments, performance is measured in the number of parallel replication servers and the maximum transactions-per-second for all concurrent processes. See Also SPARC T4-2 Server oracle.com OTN Oracle TimesTen In-Memory Database oracle.com OTN Oracle Solaris oracle.com OTN Oracle Database 11g Release 2 Enterprise Edition oracle.com OTN Disclosure Statement Copyright 2012, Oracle and/or its affiliates. All rights reserved. Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners. Results as of 1 October 2012.

  Read the article

• Do I need to be worried about these SMART drive temperatures?

  - by Steve Lorimer

  I have 5 hard drives in a machine sitting in a cupboard. /dev/sda is a 500GB Seagate drive, and is the boot disk. /dev/sd{b,c,d,e} are 2TB drives in a raid6 configuration. smartctl is showing significantly higher temperatures (like ~140 degrees celsius) on the raid drives than the boot drive. Do I need to be worried? /dev/sdb and /dev/sde are new Western Digital Black drives (new=1 week) /dev/sdc and /dev/sdd are 5 year old Hitachi drives /dev/sda [SAT], Temperature_Celsius changed from 40 to 39 /dev/sdc [SAT], Temperature_Celsius changed from 142 to 146 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 142 /dev/sdd [SAT], Temperature_Celsius changed from 142 to 146 /dev/sda [SAT], Airflow_Temperature_Cel changed from 61 to 62 /dev/sda [SAT], Temperature_Celsius changed from 39 to 38 /dev/sde [SAT], Temperature_Celsius changed from 107 to 108 /dev/sdb [SAT], Temperature_Celsius changed from 108 to 109 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sda [SAT], Airflow_Temperature_Cel changed from 62 to 61 /dev/sda [SAT], Temperature_Celsius changed from 38 to 39 Update: Adding detailed drive information as per request: /dev/sda =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Pipeline HD 5900.2 Device Model: ST3500312CS Serial Number: 5VV47HXA LU WWN Device Id: 5 000c50 02aad5ad6 Firmware Version: SC13 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5900 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdb =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1398726 LU WWN Device Id: 5 0014ee 003b8bd25 Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdc =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WSTUD LU WWN Device Id: 5 000cca 369cc9f5d Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdd =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WST4D LU WWN Device Id: 5 000cca 369cc9f48 Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sde =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1483782 LU WWN Device Id: 5 0014ee 3002d235c Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled

  Read the article

• ArchBeat Link-o-Rama Top 10 for August 2012

  - by Bob Rhubart

  The Top 10 most popular items shared via the OTN ArchBeat Facebook page for the month of August 2012. Now Available: Oracle SQL Developer 3.2 (3.2.09.23) New features include APEX listener, UI enhancements, and 12c database support. The Role of Oracle VM Server for SPARC in a Virtualization Strategy In this article, Matthias Pfutzner discusses hardware, desktop, and operating system virtualization, along with various Oracle virtualization technologies, including Oracle VM Server for SPARC. How to Manually Install Flash Player Plugin to see the Oracle Enterprise Manager Performance Page | Kai Yu So, you're a DBA and you want to check the Performance page in Oracle Enterprise Manager (11g or 12c). So you click the Performance tab and… nothing. Zip. Nada. The Flash plugin is a no-show. Relax! Oracle ACE Director Kai Yu shows you what you need to do to see all the pretty colors instead of that dull grey screen. Relationally Challenged (CX - CRM - EQ/RQ/CRQ) | Chris Warticki Self-proclaimed Oracle Support "spokesmodel" Chris Chris Warticki has some advice for those interested in Customer Relationship Management: "How about we just dumb it down, strip it to the core, keep it simple and LISTEN?! No more focus groups, no more surveys, and no need to gather more data. We have plenty of that. Why not just provide the customer what they are asking for?" Free WebLogic Server Course | Middleware Magic So you want to sharpen your Oracle WebLogic Server skills, but you prefer to skip the whole classroom bit and don't want to be bothered with dealing with an instructor? No problem! Oracle ACE Rene van Wijk, a prolific Middleware Magic blogger, has information on an Oracle WebLogic course you can take on your own time, at your own pace. Oracle VM VirtualBox 4.1.20 released Oracle VM VirtualBox 4.1.20 was just released at the community and Oracle download sites, reports the Fat Bloke. This is a maintenance release containing bug fixes and stability improvements. Optimizing OLTP Oracle Database Performance using Dell Express Flash PCIe SSDs | Kai Yu Oracle ACE Director Kai Yu shares resources based on "several extensive performance studies on a single node Oracle 11g R2 database as well as a two node 11gR2 Oracle Real Application clusters (RAC) database running on Dell PowerEdge R720 servers with Dell Express Flash PCIe SSDs on Oracle Enterprise Linux 6.2 platform." Oracle ACE sessions at Oracle OpenWorld With so many great sessions at this year's event, building your Oracle OpenWorld schedule can involve making a lot of tough choices. But you'll find that the sessions led by Oracle ACEs just might be the icing on the cake for your OpenWorld experience. MySQL Update: The Cleveland MySQL Meetup (Independence, OH) Oracle MySQL team member Benjamin Wood, a MySQL engineer and five year veteran of the MySQL organization, will speak at the Cleveland MySQL Meetup event on September 12. The presentation will include a MySQL 5.5 Overview, Oracle's Roadmap for MySQL, including specifics on MySQL 5.6, best practices and how to overcome development and operational MySQL challenges, and the new MySQL commercial extensions. Click the link for time and location information. Parsing XML in Oracle Database | Martijn van der Kamp Martijn van der Kamp's post deals with processing XML in PL/SQL code and processing the data into the database. Thought for the Day "Walking on water and developing software from a specification are easy if both are frozen." — Edward V. Berard Source: SoftwareQuotes.com

  Read the article

• Must go through Windows Boot Loader to get to Grub

  - by Zach

  I just installed a fresh copy of Precise alongside Windows 7. I have to separate 750GB hard drives; /dev/sda holds the Windows partitions and /dev/sdb holds the Ubuntu partitions. Other than that, these are fresh installs of both Windows 7 and Ubuntu 12.04. Whenever I boot, Grub doesn't load, instead it goes to a black screen with a single blinking (horizontal bar) cursor in the top right corner. However, if I boot, hit escape right as the BIOS/POST screen finishes up, see the Windows Boot Loader and hit escape to make it go back to the BIOS screen. After the BIOS screen, grub shows up and everything functions normally; I can boot into Ubuntu or Win7. I don't want to have to do the Escape, Escape, Wait, Boot trick every time. I have no idea what would be wrong or what information I could give you guys to help diagnose. I have run a sudo update-grub and it found everything normally. I tried adding nomodeset flag in the /etc/default/grub line GRUB_CMDLINE_LINUX_DEFAULT which searching around made me think might work. Thoughts on what I could do to fix this? EDIT: I've tried changing the boot order so that both drives in the BIOS (both are labeled as "Internal HDD") have had a try booting first. I think the problem may be that every time I boot, the BIOS boot order is different... and I have to reset it. It seems to not be stable... but I'm not sure how to go about fixing that either. The machine has both traditional BIOS and UEFI. It came standard in "Legacy" mode; so it is currently set to boot through Legacy mode. I've reinstalled Ubuntu now, and now if I hit escape at the end of the BIOS/POST startup screen, it takes me to GRUB menu. Otherwise it automatically loads Windows. It seems like GRUB is now the acting bootloader, it just doesn't automatically start that unless I ask it to open a bootloader. In my other machines, it has always automatically started at the end of BIOS/POST. EDIT2: Using gparted, I just looked at my partitions, it would seem that my linux-swap partition is currently flagged as the boot partition for my Ubuntu install. I currently only have 2 partitions: one of "ext4" with a mount point of "/" and flag " "; and the "linux-swap" with mount point " " and flag "boot." If I change the boot flag to be on "/," it does not reliably solve the problem. After 10 boots: 2 Booted successfully to GRUB 5 Booted directly to Windows 7 3 booted to the black screen with the cursor and hung there Further research makes me think this is an issue of the BIOS not reliably booting hard drives in the same order or not finding both hard drives. If I ask it to create a "boot menu" sometimes it has 2 entries for "Internal HDD," sometimes 1. Also the list it creates changes order every time I bring it up; so it is not following a consistent boot sequence. Will report back if this is not an issue with GRUB.

  Read the article

• problem on my site [closed]

  - by ali

  Errors found while checking this document as XHTML How and from where repaired ,please help my hello, I have a problem on my site, was discovered by the program (A1 website analyzer) you can fix my site? Because I really do not know about the programming language, if it please email me and thank you please see this link it http://jigsaw.w3.org/css-validator/validator?uri=http://www.moneybillion.com/#errors Validation Output: 19 Errors Line 193, Column 261: there is no attribute "data-count" …ass="twitter-share-button" data-count="horizontal" data-via="elibeto1199"Twee…? You have used the attribute named above in your document, but the document type you are using does not support that attribute for this element. This error is often caused by incorrect use of the "Strict" document type with a document that uses frames (e.g. you must use the "Transitional" document type to get the "target" attribute), or by using vendor proprietary extensions such as "marginheight" (this is usually fixed by using CSS to achieve the desired effect instead). This error may also result if the element itself is not supported in the document type you are using, as an undefined element will have no supported attributes; in this case, see the element-undefined error message for further information. How to fix: check the spelling and case of the element and attribute, (Remember XHTML is all lower-case) and/or check that they are both allowed in the chosen document type, and/or use CSS instead of this attribute. If you received this error when using the element to incorporate flash media in a Web page, see the FAQ item on valid flash. Line 193, Column 283: there is no attribute "data-via" …ton" data-count="horizontal" data-via="elibeto1199"Tweet This error may also result if the element itself is not supported in the document type you are using, as an undefined element will have no supported attributes; in this case, see the element-undefined error message for further information. How to fix: check the spelling and case of the element and attribute, (Remember XHTML is all lower-case) and/or check that they are both allowed in the chosen document type, and/or use CSS instead of this attribute. If you received this error when using the element to incorporate flash media in a Web page, see the FAQ item on valid flash. Line 193, Column 393: required attribute "type" not specified …ript" src="//platform.twitter.com/widgets.js"var facebook = {? The attribute given above is required for an element that you've used, but you have omitted it. For instance, in most HTML and XHTML document types the "type" attribute is required on the "script" element and the "alt" attribute is required for the "img" element. Typical values for type are type="text/css" for and type="text/javascript" for . Line 194, Column 23: element "data:post.url" undefined url : "",? You have used the element named above in your document, but the document type you are using does not define an element of that name. This error is often caused by: incorrect use of the "Strict" document type with a document that uses frames (e.g. you must use the "Frameset" document type to get the "" element), by using vendor proprietary extensions such as "" or "" (this is usually fixed by using CSS to achieve the desired effect instead). by using upper-case tags in XHTML (in XHTML attributes and elements must be all lower-case). Line 197, Column 62: required attribute "type" not specified src="http://orkut-share.googlecode.com/svn/trunk/facebook.js"?

  Read the article

• Jquery Fancybox not working after postback

  - by Lee Englestone

  I have a Fancybox (or more accurately) a number of fancy boxes on an asp.net page. My Fancybox (jquery plugin) works fine until a postback occurs on the page then it refuses to work. Any thoughts? Anyone experienced similar behaviour? UPDATE : Some Code.. I have a databound repeater with a fancybox on each repeating item. They are instanciated by (outside the repeater) $(document).ready(function() { $("a.watchvideo").fancybox({ 'overlayShow': false, 'frameWidth' : 480, 'frameHeight' : 400 }); }); The anchor tag is repeated.. href="#watchvideo_<%#Eval("VideoId")%" As is a div with id="watchvideo_<%#Eval("VideoId") %> As is a script element that instanciates the flash movies Yes the VideoIds are being output the the page. UPDATE : It's not a problem with the flash.. It is not a problem with the flash as i've tried it without the flash, it wont even pop a window with a simple message in. UPDATE : I wonder if it is the updatepanel. http://stackoverflow.com/questions/301473/rebinding-events-in-jquery-after-ajax-update-updatepanel -- lee

  Read the article

• Problem Rendering SIFR with revision 436 on IE6 and IE7

  - by Mark

  Hi, I seem to have a problem with SIFR3. I'm using version 436 and from all my testing it appears to be a problem associated with IE6 and IE7 as I cannot replicate the issue in Firefox, Chrome, Safari for Windows, or even IE8. The problem is occurring on my company's website and can be seen here: http://www.wyldeia.co.uk/blog.php When you first go to the page in IE6 or IE7 it appears to render fine. However if you click away onto another page and then click the back button in the browser, all of the text is replaced by an error saying "Rendered with sIFR3 revision 436". If you refresh the page, then the problem goes away, that is until you browse away and come back again. I've tried this on two separate machines both running IE7.0.6000.16809, and a further separate machine running IE6 which I then upgraded to IE8. I thought initially it might be Flash player related but on upgrading from version 9 to 10 of the flash player the problem remains. Further digging around indicated that the error can be caused by having a corrupted flash font file, or having one present that was generated with a previous revision of SIFR3. However I have exported the flash font file using the supplied fla with revision 436 but the problem remains. Usually I like to track the answer down myself but as it is I'm at a bit of a loss on this one so if anyone has any ideas what might be happening here then I would be very grateful! Regards, Mark

  Read the article

< Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >