Search Results

Search found 8367 results on 335 pages for 'temporal difference'.

Page 174/335 | < Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >

• Is there a way to create a consistent snapshot/SnapMirror across multiple volumes?

  - by Tomer Gabel

  We use a NetApp FAS 6-series filer with an application that spans multiple volumes. For backup purposes I would like to create a consistent snapshot that spans these volumes at the same point in time (or at least with an extremely low delta); additionally, we'd like to to use SnapMirror to replace the production environment to test volumes. The problem is in creating a consistent snapshot/SnapMirror, since these commands are not transactional and do not take multiple parameters. I tried scripting consecutive "snap create" or "snapmirror resync" commands via SSH, but there's always a 0.5-2 second difference between each snapshot. It's currently "good enough", but I'm seriously concerned about the consistency impact with increased load (we're currently in pre-production). Has anyone managed to create a consistent snapshot that spans several volumes? How did you pull it off?

  Read the article

• Netgear router-speed problem after XBox use

  - by John Dudley

  When my son is at my place at the weekend, he plays XBox Live over the internet, using my wireless network (Netgear 'g' type router). This usually thrashes & crashes the router to the extent I have to hard-boot it to get it working again. However, after this weekend, on my two laptops, I'm left with the problem that the router is working, but I'm only getting 0.38Mbps out of it, at all times of the day. I've tried hard-booting the router, but no difference. Could this be a knock-on effect of the Xbox use? I can't believe the router could be damaged, but working slower? Is that possible? Tiscali haven't come back to me yet on any 'network' issues. Thanks in advance

  Read the article

• Apache log file problem

  - by Luke

  I've recently set up an Apache 2 web server and I noticed a quite a few lines in the error and access log that start with the follow sequence (but longer). Does anyone know where this comes from? ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@ ....... My set up is an Apache 2 load balancer with mod_balancer enabled and two Apache 2 web servers. All three servers write to the same log files on a share located on a NFS. My first guess is that my problem has to do with it since it's the only difference that comes to mind from other set ups I've used in the past but I'm not sure.

  Read the article

• inodes and tree-depth in ext2

  - by David Hagan

  I have an ext2 filesystem with a maximum number of inodes per directory (somewhere around 32k), and also a maximum number of inodes in the entire filesystem (somewhere around 350m). Because I'm using this filesystem as a datastore for a service that has in excess of 32k objects, I'm distributing those objects between multiple subdirectories (like a dictionary separates A-K and L-Z). My question is this: Is there any significance to the tree depth when I'm building these inodes? Is there a significant difference or limitation that's going to affect my service if I choose "/usr/www/service/data/a_k/aardvark" over "/data/a_k/aardvark"?

  Read the article

• Teredo - how to connect to host behind NAT?

  - by Signum

  All I want to achieve is to establish connection to my simple server (written in C# using TcpListener class, if it makes any difference), on my computer which is behind NAT. It has some IPv6 address (it's public IP, starting with 2001:0) on Teredo interface. However, I cannot even ping it from outside my network, for instance I'm trying to ping this address from this website http://mebsd.com/ipv6-ping-and-traceroute, result - 100% packet loss. As I understood from reading about Teredo, there is no need for some port forwarding? So where could be the problem?

  Read the article

• Virtual Machine Performance - More RAM or More Processor?

  - by webworm

  When looking to improve Virtual Machine performance what would be better ... Increasing the available RAM or increasing the processor power? Here is my choice ... Core 2 Duo @ 2.4 GHz with 8 GB RAM and integrated graphics (Mac Book Pro 13") Core i7 @ 2.6 GHz with 4 GB RAM and 512 MB dedicated graphics (Mac Book Pro 15") I plan to run Windows x64 in the VM with SQL Server 2008, Visual Studio 2010, and SharePoint 2010. I am planning to run VMWare Fusion v3. I also didn't know if a dedicated graphics card makes a difference when using a Virtual Machine. Thank you.

  Read the article

• How to make playing track in Foobar2000 more noticeable?

  - by cipricus

  The current playing track is signaled only by a very discreet arrow - no bold, no highlight, no different color. The only 'highlighting'happens by selecting tracks. In other players the difference between selected tracks and highlighted/playing tracks is obvious. Are there some settings - I don't mean skins - that would improve this? Edit considering my answer below: maybe that line $if(%isplaying%, ? ? ? ? ? ? ? ?) could be edited to make the track bold or of a certain color?

  Read the article

• Transferring websites from x64 to x86 server

  - by Ke

  Hi, I run a x64 staging server here along with the following: Solr Java etc. However, I am about to get a linode vps for production and quickly realising that x86 is the way to go for their lowest RAM package (thinking to upgrade later). My staging server is x64 with 12gb ram, so going down to 300mb ram is going to feel devilishly slow ;/ Here are my questions: 1) Will I have problems transferring my scripts, dbs etc from a x64 to x86 server? e.g. solr indexes 2) Is it worth going for the x86 package? I am probably going to upgrade later down the line and x64 might be better for the servers with more RAM? should I stick with x64 instead as there isnt much difference when using with low RAM? Cheers Ke

  Read the article

• Why is my Wifi connection slower than ethernet even though bandwidth should saturated?

  - by supercheetah

  I'm wondering why it is that my wireless connection is slower than my wired connection for things going to the outside world (so, not files being transferred within the network), which is should be faster than the outside connection, which, I would think, would mean that downloading something like an ISO or other large file from the Internet should be the same either way since that should saturate the connection anyway. Does it have something to do with the encryption (WPA)? Could it have something to do with MTU since the MTU for ethernet can be in the range of 1500 to 9000 bytes, and 2304 bytes for 802.11? Do wireless packets have to be buffered, whereas this wouldn't be an issue with ethernet? What's the math behind the difference?

  Read the article

• Understanding DHCP setting for DNS Server Options and Scope Options

  - by Saariko

  I have installed 2 DC's on my network (W2K8 R2) both serve as a replicate DC on my domain. On one of them (DC1) there is also a DHCP server running. On both I have a DNS server running. I am trying to understand the difference in the settings within the DHCP of Server Options and Scope Options. As I understand it: On the server options, I should put an external DNS for system (lets say 8.8.8.8 - google) And on the scope options, I should put both my internal dc1 and dc2 IP's as the server. - which are than distributed to my domain clients. Is that correct? Is there a better way? Do I need to add loopback address as well?

  Read the article

• Use Windows Briefcase from the command line

  - by Daniel

  I have a thumb drive on which I take many of my files with me. I would like to synchronize it with my computer automatically when I connect it. I currently have a script run every time I connect it so that I can do the many things that need to be done when it connects (check for updates to the portable applications, etc.). I want my synchronization utility to: Detect conflicts work correctly when I move files or change the folder structure tell the difference between a file that was deleted on one side and a file that was added on the other work from the command line or at least have a command that will open up a window provide a confirmation screen before doing anything The Windows Briefcase does all of these except the command line. Is there any program that does all of these, or is there a way to synchronize the briefcase from the command line?

  Read the article

• DSL vs Cable latency

  - by tovmeod

  currently I have a 10Mbps DSL line and I'm thinking to switch to a cable since they got 100Mbps for a little less than double the price I'm paying for 10Mbps. In other words the cable company is offering 100Mbps for the price of 20Mbps DSL. Since 10Mbps is more than enough for me I am worried about the latency, I saw this that is just a guy experiment, that shows that cable and DSL are the same in practical terms, and this but I couldn't grasp it, not sure if it is helpful. So my question is if there's any practical difference between cable and DSL, mainly in latency terms but I would be also interested in other advantages/disadvantages. This is for my home connection, I work from home but I don't run any server, I most of the time code, skype and eventually game.

  Read the article

• Internet connectivity issues with one router but work ok with other router

  - by user825904

  I have one Tplink ADSL ROUTER and when i enter username and password on setup page then everything works fine. Now i have one more router Netgear router then when i enter same username and password then interworks ok for some 50% websites but for other 50% websites the page is not loaded and it hangs there. In the sats bar it says website found , waiting for reply and it hnags there and no site is displayed. I wonder which setting is different on these two routers. The Tplink router i have bought is from local shop but netgear router is from different country. Can that make some difference

  Read the article

• Eclipse: would more CPU cores with HyperThreading help increase speed?

  - by Dylan

  I'm programming a very large project in Eclipse. Right now I use a dual core machine with 2GB RAM, but Eclipse is sometimes busy for minutes (refreshing/indexing/building), so I'm upgrading to a new machine (with 16GB RAM and an SSD). Now I must choose between an Intel 2500K or an Intel 2600K that has HyperThreading. The price difference is about $100. Would that be worth it, for Eclipse, or is more memory/faster drive much more important for Eclipse ? Can Eclipse make use of the HyperThreading at all?

  Read the article

• What are the quality metrics for RAM?

  - by Hi-Tech KitKat Android

  I have searched RAM and i found there are given some specification for the same capacity RAM, What are the difference and performance comparison between these? Like RAM1 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-800/PC-6400 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 400 MHz Technology DDR2 SDRAM Memory CAS Latency 4, 5, 6 RAM 2 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-667/PC2-5300 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 333 MHz Technology DDR2 SDRAM Memory CAS Latency 3, 4, 5 RAM3 General Brand Kingston Memory Type 2 GB (64 x 256 MB) 800 MHz DDR2 DIMM Compatible Device PC Pins 240-pin Error Check Non-ECC Buffered/Unbuffered Unbuffered Memory Memory Clock 200 MHz Technology DDR2 SDRAM Memory CAS Latency 6 What are the affect of the following Memory Type(given as 8 x 128 MB) Memory Clock (given in MHz) CAS Latency (given as 4,5,6) my Requirement is 2 GB DDR2 Type Desktop Please help

  Read the article

• Asterisk does not recognise DTMF tones from mobile phones

  - by Eugene van der Merwe

  We have an Asterisk 1.8.7.0 (the Elastix derivative) switchboard. Every since a month ago, seemingly out of the blue, the switchboard does not recognise DTMF tones any more from mobile phones. Testing the switchboard using 7777 works. Testing the switchboard from a normal phones works. Testing the switchboard from a mobile phone fails. Looking at the log file I can't see anything. I used 'asterisk -rvvvv' and 'tail -f /var/log/asterisk/full' to see the live output and scan the logs. I guess I don't see anything because it's simply not recognising the DTMF tones. I did brief research and found an old setting for SIP phones, 'rfc2833compensate=yes', and tried adding this to 'sip_general_custom.conf'. After that I did 'core restart when convenient' but that didn't make any difference. Could anyone give me some additional troubleshooting steps?

  Read the article

• Correct password for ssh key rejected when ssh-d into machine

  - by user20342

  When I am logged into my machine directly, I can do all git operations, and when prompted for a password, the password is accepted. When I ssh into the same box and run git operations on the same repos, the password is rejected. Relevant section of .ssh/config looks like this: # Generic settings Host * ServerAliveInterval 600 ControlPath /tmp/ssh-%r@%h:%p ControlMaster auto KeepAlive yes IdentityFile ~/.ssh/id_rsa.pub Transaction looks like this when I login when I ssh into my box: {12-12-03 9:41}hbrown-wks2:~/workspace/spt/project@master??? hbrown% git pull Enter passphrase for key '/home/hbrown/.ssh/id_rsa.pub': Enter passphrase for key '/home/hbrown/.ssh/id_rsa.pub': Enter passphrase for key '/home/hbrown/.ssh/id_rsa.pub': Permission denied (publickey). fatal: Could not read from remote repository. Please make sure you have the correct access rights and the repository exists. Using bash does not appear to make a difference (i.e. ssh-agent /bin/bash). This is a recent development, but I can't cite the change that caused it.

  Read the article

• Can I use wildcards is puppet package ensure to cover multiple releaseversion

  - by Rob van den Eijnde

  Using puppet I want to update packages on my (CentOS 5 & 6 servers) in a controlled way. Therefore I don't want to use ensure=>latest but rather ensure=>3.0.1-1. Example: class puppet::installation inherits puppet { package { "puppet": ensure => "3.0.1-1", } } The update works alright but puppet agent keeps complaining that there is a difference: /Stage[main]/Puppet::Installation/Package[puppet]/ensure: current_value 3.0.1-1.el6, should be 3.0.1-1 (noop) I can solve this by changing the ensure rule to 3.0.1-1.el6 but than that won't work on CentOS 5. Is there a short/clean way to solve this or do I have to write to seperate, os-releaseversion dependant rules. I have been googling for a solution but didn't find anything pertaining to this particular question. Any suggestion or reference to a relevant example would be appreciated.

  Read the article

• Mac keeps switching to second graphics card

  - by 1.21 gigawatts

  I have a MacBook Pro and whenever I enter certain apps (video camera app or Photoshop for example, the graphics card switched. I didn't know this was going on at first; just that the screen kept changing colors as I opened or closed different software. Later someone told me that the software was causing the OSX to switch graphics cards. It's annoying. How do I keep one graphics card (the better one) enabled all the time? I don't care about power consumption because it is plugged in all the time (though I'm curious how much difference it makes). I just want one graphics card enabled.

  Read the article

• How can I change my language/keyboard input language system-wide temporarily?

  - by Adam Lynch

  I currently have two languages set up; English and Dutch. The only difference is in keyboard input. The Dutch one uses the French/Belgian AZERTY layout and the English one uses the Irish/English QWERTY layout (@ = Shift+'). When a Belgian colleague needs to use my computer, I switch the language to NL (Dutch) (therefore the input to AZERTY) using the language bar, but it seems to be application-specific. (I.e: After changing the input to AZERTY for my colleague, if he then clicks on another program it switches back to QWERTY for that program). Is there a way I can quickly switch between the two comprehensively yet temporarily?

  Read the article

• Software: Launching League of Legends spectator mode from Command Line (Mac)

  - by Alex Popov

  Background: tl;dr at the end League of Legends has a spectator mode, in which you can watch someone else's game (essentially a replay) with a 3 minute delay. Popular LoL website OP.GG has figured out a clever way of hosting these spectator games on their own servers, thereby making them replayable, as opposed to only being available while the game is on (as Riot does it). If you request a replay from OP.GG, it sends a batch file which looks for where the League is situated and then the magic happens: @start "" "League of Legends.exe" "8394" "LoLLauncher.exe" "" "spectator fspectate.op.gg:4081 tjJbtRLQ/HMV7HuAxWV0XsXoRB4OmFBr 1391881421 NA1" This works fine on Windows. I'm trying to get it to work on Mac (which has an official client). First I tried running the same command by hand, (split for convenience) /Applications/ ... /LeagueOfLegends.app/ ... /LeagueofLegends 8393 LoLLauncher \ /Applications/ ... /LolClient spectator fspectate.op.gg:4081 tjJbtRLQ/HMV7HuAxWV0XsXoRB4OmFBr 1391881421 NA1 Running this, however, just starts the LoLLauncher, which closes all the active League processes. The exactly same thing happens if I just call /Applications/ ... /LeagueOfLegends.app/ ... /LeagueofLegends Next I tried seeing what actually happens when Spectator mode is initiated so I ran $ ps -axf | grep -i lol which showed UID PID PPID C STIME TTY TIME CMD 503 3085 1 0 Wed02pm ?? 0:00.00 (LolClient) 503 24607 1 0 9:19am ?? 0:00.98 /Applications/League of Legends.app/Contents/LOL/RADS/system/UserKernel.app/Contents/MacOS/UserKernel updateandrun lol_launcher LoLLauncher.app 503 24610 24607 0 9:19am ?? 1:08.76 /Applications/League of Legends.app/Contents/LoL/RADS/projects/lol_launcher/releases/0.0.0.122/deploy/LoLLauncher.app/Contents/MacOS/LoLLauncher 503 24611 24610 0 9:19am ?? 1:23.02 /Applications/League of Legends.app/Contents/LoL/RADS/projects/lol_air_client/releases/0.0.0.127/deploy/bin/LolClient -runtime .\ -nodebug META-INF\AIR\application.xml .\ -- 8393 503 24927 24610 0 9:44am ?? 0:03.37 /Applications/League of Legends.app/Contents/LoL/RADS/solutions/lol_game_client_sln/releases/0.0.0.117/deploy/LeagueOfLegends.app/Contents/MacOS/LeagueofLegends 8394 LoLLauncher /Applications/League of Legends.app/Contents/LoL/RADS/projects/lol_air_client/releases/0.0.0.127/deploy/bin/LolClient spectator 216.133.234.17:8088 Yn1oMX/n3LpXNebibzUa1i3Z+s2HV0ul 1400781241 NA1 Of Interest: there is (LolClient) which I cannot kill by it's PID. UserKernel updateandrun lol_launcher LoLLauncher.app is launched first. LoLLauncher is launched by the UserKernel (as we can see from the PPID) The very long command (PID: 24927) is how Spectator mode is launched, and is also launched by UserKernel. Spectator mode is launched in exactly the same way that the OP.GG .bat wanted to, with the only difference that Spectator mode connects to Riot instead of OP.GG's spectate server. I tried attaching GDB to the LolClient, but I couldn't get anything meaningful from it since it's an Adobe AIR application (and I've never used GDB with code other than mine own). Next I ran dtruss -a -b 100m -f -p $PID on everything I could think of: the LolClient, the LolLauncher and the UserKernel and skimmed the half a million lines produced. I found stuff like the GET request used to get the information of the game to spectate, but I could not see any launch of the equivalent of League of Legends.exe with spectator options. Finally, I ran lsof | grep -i lol to see if anything else was opened in the process, but didn't find anything that seemed appropriate. Open were UserKernel, LolLauncher, LolClient, Adobe AIR, LeagueofLegends and then Bugsplat, all of which are expected. None of this seemed especially relevant to figuring out how LeagueofLegends was opened into spectator mode. It obviously can be done, since Spectator mode is accessible from within the client. It seems likely that it can be done from the CLI, since Windows can do it and the clients are supposed to equals. Unless I'm missing something in the difference between how UNIX and Windows handle CLI application launches. My question is if there are any other things I can try to figure out how to launch Spectator mode myself. tl;dr: Trying to get into spectator mode from the CLI. It's possible on Windows (see first code block) but it just restarts League on Mac. What else can I try to find what call is made, and how to reproduce it? PS: Please let me know how I can improve this question or its formatting, I'd love to use StackOverflow/SuperUser, but as the guys said on the podcast this week (Ep. 59) it's very intimidating. Sorry for posting this on StackOverflow the first time :(

  Read the article

• Photoshop not loading fonts correctly

  - by Brett

  I'm running Photoshop CS4 on WinXP and I have been sent a PSD as well as the needed fonts. I have installed all the fonts I got into the Windows fonts directory. When I open up the PSD in photoshop it tells me I am missing some fonts, then when I go to click on some text it tells me you are missing Roboto Bold or Roboto Regular. I check the font dropdown list in Photoshop and I see Roboto and that's it, not sure if that is correct or not? I then go to the windows fonts dir to confirm all the fonts are there and they are. See below.. Now I'm not sure if it makes any difference that the PSD I believe was made on a MAC & I'm on a PC?

  Read the article

• portable usb harddisk regardless in windows and ubuntu / linux environment

  - by user8184

  I am doing web development mostly in ubuntu. Sometimes i need to go into windows to do other administrative work. Now i am ignorant about file systems. I cannot tell the difference between NTFS and FAT32. My eyes just glaze over the wikipedia articles. All I know is i have been using this 320 Gb portable USB harddisk to save files when I am in ubuntu and when I am in windows. Now i got a situation where sometimes the windows 7 cannot detect the harddisk. I believe it has to do with the file system issue. Or my harddisk is coming apart. To make it easy to backup my files in a portable USB harddisk regardless in ubuntu or windows, please advise me. That means i can go from from linux/ubuntu to portable harddisk read/write files from windows 7 to portable harddisk read/write files the same files. Thank you.

  Read the article

• Can using higher rated battery damage device?

  - by Anwar Shah

  I am in need of a battery for my Lenovo 3000 Y410 Laptop. It's installed battery has voltage rating of 10.8v. But the shop i've consulted has only a battery of 11.1v rating. Should I buy the battery? I mean, Does using that battery can damage my laptop? An answer with some good source from hardware vendor will be very much helpful. Please do not just put your opinion. Because I do not see any difference in your opinion and my opinion. My opinion is also "It is bad". But I need some reliable source.

  Read the article

• Scanned JPEGs are large and slow to load - can they be optimized losslessly?

  - by Alistair Knock

  I have hundreds of JPEG photographs which were scanned about 5 years ago from negative using a Konica Minolta DiMAGE Scan Dual IV. The dimensions are ~4500x3000, and the filesize is around 12Mb, compared to shots from a DSLR with dimensions of 3000x2300 and filesize of 2-4Mb (actually, these are the output from a RAW convertor). The filesize is obviously quite a big difference, but the issue that's bothering me is that the (perceived) loading time is at least 10 times slower. Is this size/speed discrepancy likely to be because the scanner software saved the JPEGs inefficiently / using an old compression format, or is it simply that the scanned negatives contain much more "detail" (in the form of grain/noise) than the digital images? If the former, is there a way to losslessly optimize them? I've tried re-exporting the scanned files to full size JPEG from my RAW software but the filesize is pretty much the same. Both files will have been saved at 100 quality.

  Read the article

< Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >