Search Results

Search found 12371 results on 495 pages for 'ok'.

Page 176/495 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

  • To Delete or Not to Delete Arcserve Makeup Jobs?

    - by Cliff Racer
    Every once in a while, I have a backup job that fails with my backup server running ARCserve 12.5. A failure results in the creation of a 'makeup' job. I run the makeup job and even if it completes it stays in my job cue. These have piled up over the past couple of years and I find myself wondering if its ok to delete them knowing that ARCserve relies on a sql database to catalog backup info and data. If I run a makeup job, can I just delete it afterward? Should I just collect them? I have not seen anything so far that makes me feel confident with what to do with these leftover jobs.

    Read the article

  • "This computer has dynamically assigned IP addresses" error when installing Active Directory Domain Controller

    - by smhnaji
    This is a working Windows Server 2008 that I should install Active Directory on it. I found http://www.howtogeek.com/99323/ and followed the steps. After Additional Domain Controller Options, I'm asked the question "This computer has dynamically assigned IP addresses". As I see, the message states that Dynamic IP addressing has been used for the server, while this is wrong. When I come to Network And Sharing Center, and click on Local Area Connections - Properties - Internet Protocol Version 4 (TCP/IPv4) - Properties, I see that the main IP address (as well as DNS Server) and also all other IP addresses are assigned statically. So it should be OK. I cannot believe any server using dynamic IP(s)! Note: No IPv6 has been set for the server. Please tell me why the error is given and which of the options available, should I choose? Note that it's a production server and is working with many users in WORKGROUP. No change should be affected nor to the IPs, neither to users connecting to the server.

    Read the article

  • Is there anyway to build a raid system without all drives?

    - by xenoterracide
    I'm building a raid1 (ok it will probably be a raid10,f2 but the difference with 2 drives... isn't much) system with 2 1TB drives. However, 1 of the drives I've ordered is bad so I'm RMA-ing it. I'm wondering if I could partition and install to the 1 drive and then rebuild the array when I get the second drive (after I test it of course) My initial investigation doesn't show me a way of creating the array without specifying all devices... and the device the second drive will be is one that has data that I will need to migrate (plus it's not big enough). Is it possible that I could create an array without specifying all devices? or specify false ones and reconfigure to the right ones later? Or some other method I'm not thinking of.

    Read the article

  • Windows server 2008 r2 console stuck at "waiting for user profile service"

    - by support
    Hi, I have a windows 2008 R2 server, running on dell poweredge t300. Using hyper-v to run a windows 2008 R2 server also. Suddenly, today, my virtual console (on the virtual copy of windows 2008 server r2) will not let me login as administrator. It starts to login but then sticks at the message: Please wait for the User profile Service and is unresponsive to keypresses (incl ctrl-alt-del). The only way out is a crash. It starts up in safe mode without networking ok but not in safe mode with networking. Any suggestions on how to fix this would be appreciated Thanks

    Read the article

  • Outlook.com custom domain, Exchange ActiveSync too many connected devices

    - by Mike C.
    I just setup Outlook.com to run on a custom domain. The web interface works well but when I connect it to Outlook 2013 I get the following error: There are too many devices syncing with this account. To sync using Outlook, try removing another device that is connected with this account such as a phone or another computer. File: outlook\pstprx\storeas\utils\airsyncstatuscodes.h Line: 88 HTTP/1.1 200 OK FolderStatus: 177 To re-try press F9... Error Code: 0x80004005 I've done my home work, using Google, and found that it is often due to having 3 or 4 devices connected to an account with 50+ folders. My account is empty, no email or folder, and is not synced with any devices, I confirmed that on http://devices.live.com. I'm out of option, any help would be greatly appreciated! Thank you

    Read the article

  • Chrome not selecting correct language for Help tab

    - by Andy
    When I click Help in Chrome, a new tab appears with the Google help links etc as expected, but I have a message saying: "This Help Centre is not currently available in your language...", etc. The drop down box at the bottom is not selected correctly for en-GB (my location). Instead it is set at the first language on the list. This happens if I am signed in to my Google account or not. Selecting English from the drop-down works ok, so no great drama. Just wondering if anybody else sees this behaviour? EDIT: Using current stable build 8.0.552.224

    Read the article

  • safeboot and wubi

    - by G S
    Hi, Having read various posts it seems clear that installing Wubi on a machine which already has safeboot installed with disk encryption is a non-starter at the moment - nor is repartitioning the disk it would seem. However while the c: partion is encrypted - it has an NTFS formatted q: partition that is not encrypted and has about 4GB free - so I was wondering if there was any way to install WUBI using that partion. Obvisouly stil need a means of booting into it without stuffing my safeboot booting mechanism. I'm thinking that this should be possible as the safeboot booting mechanism will get me to the boot choice options and thereafter all references in the boot.ini entry for the wubi installtion should be to files on the non-encrypted NTFS partion and so it should be OK and not attempt any changes to my envrypted c: partion (other than adding the extra entry to boot.ini) ? any thoughts? ta

    Read the article

  • unable to access shared drives n win7

    - by colin
    OK, this is doing my head in. Not your usual Win7 sharing problem. Just built a win 7 comp to go onto my home lan and be accessed by all on the network, mostly running XP SP3. Installed it as a single HD+DVD system, got it happy, then added my storage drives, set them up in the right order and letters, rebooted, and shared them. Couldn't access the computer at all from any XP machine. Set the pasword thingy in win7 to NO, and now I can "see" all four shared drives from any machine, but can access only two of them. Please tell me whats going on as I've done nothing different from one drive to the other, just installed and set up drive letters as normal, then shared the damn things. The odd thing about it? the two 1.5T drives that have a lot of data on board are accessable, the two nearly empty 500G ones are not. ANY ideas? Cheers, Colin

    Read the article

  • Micro sound breaks/interrupts on Windows 7

    - by cand
    Hello all, I've been experiencing strange behavior recently. When listening to mp3 or watching movie or whatever that uses sound, I get micro breaks in sound. It's like it hangs or cuts a fragment for about 0.5s. When I start OS, it's ok, but as time passes it gets worse, to the extent that music is unlistenable being interrupted every 2 seconds. I haven't found any relevance between this behavior and hardware usage, I don't think it's directly related to HDD (or it might be but with significant delay). I have updated soundcard drivers and it didn't help a lot. My system is Windows 7, computer is simple HP laptop, nx7300-Ru374ES with WD Caviar Scorpio Blue hard drive inside and integrated soundcard on it (I can check the model later if it's important). Did anybody encounter such problem ? Maybe it's a common thing on Windows 7 or someone knows how to solve it? Thanks in advance.

    Read the article

  • determine what is invoking refresh/F5 in WinXP?

    - by Chris Hulan
    My laptop recently started invoking refresh (F5) on its own. Works OK from start-up/reboot but then for no apparent reason will start refreshing Initially thought it was a web page scripting issue, as I noticed it while browsing. But then found it occurs with the browser closed. Not sure if this could be a hardware issue, or some silly virus, or just a bug? Would like a utility that could tell me what device/program is invoking the refresh. Any ideas? thanks

    Read the article

  • MS SQL 2000 and SSL Certificate

    - by smoak
    I'm trying to set up a MS SQL 2000 server to use an already existing SSL certificate installed on the server. I verified that the certificate shows up in the Personal/Certificate folder of the account that is running the MSSQLSERVER service using the Certificate MMC snap-in. I also verified that the certificate for the CA is installed under the Trusted Root Certificate Authorities. Additionally, to make sure that it is using this specific certificate I created a Certificate registry value of type REG_BINARY in: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\MSSQLServer\MSSQLServer\SuperSocketNetLib and I set it to the certificates thumbprint like it mentions in: http://support.microsoft.com/kb/276553 Finally, I opened up the Server Network Utility, checked Force protocol encryption, clicked OK, and restarted the MSSQLSERVER service. Unfortunately, it fails to start and looking at the event log it's failing with: 19015: Encryption requested but no valid certificate was found. SQL Server terminating. I'm at a loss. Any ideas? Where did I go wrong?

    Read the article

  • Easy shorewall question : allow ips to DNAT

    - by llazzaro
    Hello, At my home network I had a transparent proxy. This is the rule that forward all 80 traffic to my squid3.1 server at DMZ DNAT loc:!10.0.0.126 dmz:172.16.0.198:3128 tcp 80 - !172.16.0.198 Ok, I need to add more ips to avoid transparent proxy. I tried loc:!10.0.0.134,!10.0.0.126...but didnt work (also similars like [ip0,ip1]. I tried to google the answer cant find it (sorry no matches, not searching the right keywords) also I tried to read the docs, but they are really long (and indexes dont help me). Thanks!

    Read the article

  • Windows 2008 IIS 7 PHP Caching / Blank Page Problems?

    - by darkAsPitch
    I don't even know how to explain this. The only thing I can think is 'why am I working with a windows server?' I am renting a dedicated 1and1 server - I installed PHP myself - with fast CGI and caching (pretty sure I checked OK on something about dynamic caching for PHP when I installed it.) Every few hours of intensive php processing - my pages start locking up - usually just showing blank pages - with no errors whatsoever. Just now, I checked a page - let's call it a.php - and it was showing the results of b.php - I thought I had been hacked! Simply restarting the IIS server however, fixes the problem. Any ideas / help / knowledge on similar problems with windows 2008?

    Read the article

  • Problems connecting Centos to the network when running in VMWare

    - by Sakin
    Hi, I installed CentOs on VMware running on windows XP. When trying to configure it to connect to the internet, I get an error message when trying to bring up the network interface: [root@VMLinux ~]# /et/init.d/network start Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... failed [FAILED] VM is running on a machine that has access to the network, I tried it on two different networks that have DHCP enabled. I tried to configure VMWare to use a bridged connection as well as NAT connection. An image of Ubuntu runs fine on the same VMware. What am I missing here? Thanks.

    Read the article

  • OpenVPN stopped working, what could have happened?

    - by jaja
    I have Openvpn, and it worked great when I used it on PC (Windows 8), then I copied all files (Certificates and config) to an Android 4 phone to use them. Now, Openvpn works on the phone, but not the PC. Specifically, when I open Google I get: The server at www.google.com can't be found, because the DNS lookup failed, but the VPN seems to be connected. I have a simple question, could the problem be because I copied the same files? Routing table before connecting:- IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.101 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.101 281 192.168.1.101 255.255.255.255 On-link 192.168.1.101 281 192.168.1.255 255.255.255.255 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.101 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.101 281 =========================================================================== Routing table after connecting:- IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.101 25 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 **.**.***.** 255.255.255.255 192.168.1.254 192.168.1.101 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.101 281 192.168.1.101 255.255.255.255 On-link 192.168.1.101 281 192.168.1.255 255.255.255.255 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.101 281 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Server conf:- port 1194 proto udp dev tun ca ca.crt cert myservername.crt key myservername.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt duplicate-cn keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 push "redirect-gateway def1" Client conf:- client dev tun proto udp remote 89.32.148.35 1194 resolv-retry infinite nobind persist-key persist-tun mute-replay-warnings ca ca.crt cert client1.crt key client1.key verb 3 comp-lzo redirect-gateway def1 Here is the log file:- Tue Dec 18 16:34:27 2012 OpenVPN 2.2.2 Win32-MSVC++ [SSL] [LZO2] [PKCS11] built on Dec 15 2011 Tue Dec 18 16:34:27 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Tue Dec 18 16:34:27 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Tue Dec 18 16:34:27 2012 LZO compression initialized Tue Dec 18 16:34:27 2012 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue Dec 18 16:34:27 2012 Socket Buffers: R=[65536-65536] S=[65536-65536] Tue Dec 18 16:34:27 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue Dec 18 16:34:27 2012 Local Options hash (VER=V4): '41690919' Tue Dec 18 16:34:27 2012 Expected Remote Options hash (VER=V4): '530fdded' Tue Dec 18 16:34:27 2012 UDPv4 link local: [undef] Tue Dec 18 16:34:27 2012 UDPv4 link remote: ..*.:1194 Tue Dec 18 16:34:27 2012 TLS: Initial packet from ..*.:1194, sid=4d1496ad 2079a5fa Tue Dec 18 16:34:28 2012 VERIFY OK: depth=1, /C=/ST=/L=/O=/OU=/CN=/name=/emailAddress= Tue Dec 18 16:34:28 2012 VERIFY OK: depth=0, /C=/ST=/L=/O=/OU=/CN=/name=/emailAddress= Tue Dec 18 16:34:29 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue Dec 18 16:34:29 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Dec 18 16:34:29 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue Dec 18 16:34:29 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Dec 18 16:34:29 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue Dec 18 16:34:29 2012 [myservername] Peer Connection Initiated with ..*.:1194 Tue Dec 18 16:34:32 2012 SENT CONTROL [myservername]: 'PUSH_REQUEST' (status=1) Tue Dec 18 16:34:32 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: timers and/or timeouts modified Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: --ifconfig/up options modified Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: route options modified Tue Dec 18 16:34:32 2012 ROUTE default_gateway=192.168.1.254 Tue Dec 18 16:34:32 2012 TAP-WIN32 device [Local Area Connection] opened: \.\Global{F0CFEBBF-9B1B-4CFB-8A82-027330974C30}.tap Tue Dec 18 16:34:32 2012 TAP-Win32 Driver Version 9.9 Tue Dec 18 16:34:32 2012 TAP-Win32 MTU=1500 Tue Dec 18 16:34:32 2012 Notified TAP-Win32 driver to set a DHCP IP/netmask of 10.8.0.6/255.255.255.252 on interface {F0CFEBBF-9B1B-4CFB-8A82-027330974C30} [DHCP-serv: 10.8.0.5, lease-time: 31536000] Tue Dec 18 16:34:32 2012 Successful ARP Flush on interface [26] {F0CFEBBF-9B1B-4CFB-8A82-027330974C30} Tue Dec 18 16:34:37 2012 TEST ROUTES: 2/2 succeeded len=1 ret=1 a=0 u/d=up Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD ..*. MASK 255.255.255.255 192.168.1.254 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=25 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 0.0.0.0 MASK 128.0.0.0 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 128.0.0.0 MASK 128.0.0.0 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 10.8.0.1 MASK 255.255.255.255 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 Initialization Sequence Completed

    Read the article

  • Is there a network "tee"-alike with one leg returning to /dev/null ?

    - by Steff Davies
    I've just built a new PostgreSQL server for my employers, which is happily replicating using WALs. I'm now left with the problem of verifying its performance. One nice way which came up in conversation is to break replication with the slave caught up and then direct all production traffic to both servers, discarding the responses from the new server and returning those from the current one to the clients. Once we're sure performance is OK, we re-sync the slave and can fail over with confidence. Bliss. This would require a TCP proxy capable of opening two outgoing connections for each incoming one, and discarding the data returned from one of them, which is a tricky thing to google for, it seems. Do the assembled brains know of such a thing, before I dive into libevent and write one?

    Read the article

  • Oracle Hangs on Responses Intermittently

    - by Ryan Cook
    I want to preface this with the fact that I am a developer and I am not even close to a DBA, plus I am new to Oracle. OK, here it goes: I have a Java application which uses spring and hibernate. Its a simple CRUD app and I will leave the details out as I don't think they are the issue. I have noticed that my app runs fine when I use MySql, but when I use an Oracle 10.2 server every 7th-10th hangs for 5-10 seconds. My Oracle installation was done by me using all defaults, same as the mysql install. I don't even know where to start looking. Any ideas? Thanks in advance and sorry that I lack the details that are most likely required for help.

    Read the article

  • arrow keys stop working to scroll pages

    - by Delirium tremens
    Sometimes, the arrow keys stop working to scroll pages. Sometimes, in Firefox - Tools - Options - Advanced - Accessibility - General, the first checkbox, about using arrow keys to scroll pages, appears checked and some other times, unchecked. When it's unchecked, I check it. When it's checked, I keep it checked. In both times, I click OK. Then, the arrow keys restart working to scroll pages. I'm having to do it all the time. What should I do?

    Read the article

  • Sharing an external hard drive in Ubuntu using Samba

    - by cambraca
    /media/MYDISK is where my hard drive is mounted automatically. I created a symlink using: ln -s /media/MYDISK /home/camilo/MYDISK chmod 777 /home/camilo/MYDISK I'm setting up smb.conf like this: [myshare1] comment = external disk browsable = yes path = /home/camilo/MYDISK guest ok = yes read only = no create mask = 0775 Also, in the [global] section I tried adding the following lines: follow symlinks = yes wide links = yes unix extensions = no The problem is that when browsing the shared folder in Windows 7, I get a "\\etc\myshare1 is not accessible" error. When pointing the path to a regular folder it works fine. Also, when I point it directly to /media/MYDISK, it shows the same error. EDIT: to make it more interesting, I have no graphical interface, so I need to touch the config files directly..

    Read the article

  • aptitude: list all previous recommended packages

    - by casper
    sometimes when installing a package, aptitude recommends several other packages. Is there a way to show all previous recommended packages of all installed packages? Thanks in advance. Casper Edit: Thanks for the replys so far. I already tried: aptitude show ~i | grep '^Recommends' | cut -d ' ' -f 2- Thats mostly ok. But it gives also things back like: console-setup | console-data (>= 2002.12.04dbs-1) I want an easy way, to install all missing recommended packages. So aptitude install console-setup | console-data (>= 2002.12.04dbs-1) won't work ;-) Is there a way, without manual checking all entries, to do this?

    Read the article

  • Extract number with regex

    - by Joey
    I have this string: > HTTP/1.1 200 OK Date: Tue, 12 Nov 2013 15:26:17 GMT Server: > Apache/2.2.3 (CentOS) Last-Modified: Fri, 08 Nov 2013 21:34:50 GMT > ETag: "452//path/to/file" > Accept-Ranges: bytes Content-Length: 26010 Connection: close > Content-Type: text/plain; charset=UTF-8 And would like to extract 452 which is before // and after ETag, what regex to use? I am stuck. Thanks a lot

    Read the article

  • OpenSSL missing during ./configure. How to fix?

    - by P K
    I was trying to install node.js and found OpenSSL support missing during ./configure. How can I fix it? Is it a mandatory step? # ./configure Checking for gcc : ok Checking for library dl : not found Checking for openssl : not found Checking for function SSL_library_init : not found Checking for header openssl/crypto.h : not found /home/ec2-user/node-v0.6.6/wscript:374: error: Could not autodetect OpenSSL support. Make sure OpenSSL development packages are installed. Use configure --without-ssl to disable this message.

    Read the article

  • What is the best nginx compression gzip level?

    - by Chamnap
    I'm using nginx reverse proxy cache with gzip enabled. However, I got some problems from android applications http requests to my rails json web service. It seems when I turn off reverse proxy cache, it works ok because the response header comes without gzip. Therefore, I think the problem caused from gzip. What is the most appropriate level of gzip compression? gzip on; gzip_http_version 1.0; gzip_vary on; gzip_comp_level 6; gzip_proxied any; gzip_types text/plain text/css text/javascript application/javascript application/json application/x-javascript text/xml application/xml application/xml+rss;

    Read the article

  • Join domain in windows 7 [on hold]

    - by Hassan Ali Khan
    I have created a domain on server machine and when i am trying to join a domain through another machine of windows 7 through the following steps: Goto MY Computer Properties - Change settings - ComputerName - click on change button - click on radio button "Domain" and enter domain name. After that when i click on OK button and enter the username and password credentials. It show me the following error: An attempt to resolve the DNS name of a domain controller in the domain being joined has failed. Please verify this client is configured to reach a DNS server that can resolve DNS names in the target domain

    Read the article

  • Fax in Small Business Server 2003 fails to hang up

    - by Tim Anderson
    We have a problem with fax in SBS 2003. External modem, Courier v Everything which is a recommended model. It receives a fax OK, but then sometimes (quite often) fails to hang up. Attempts to send faxes thereafter get an engaged tone. The only fix when this happens is to reset the fax modem. Even restarting the server is not enough. We've tried with a different model modem, same problem. Any ideas? Tim

    Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >