Search Results

Search found 5260 results on 211 pages for 'fedora 17'.

Page 177/211 | < Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >

• vlans on openvz, centos 6

  - by arheops

  i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

  Read the article

• Static route works on one computer, not the other

  - by Dan

  I have been struggling with this for a couple days now, maybe I just need some people with a fresh perspective to figure out what the issue is. Basically I have a bunch of computers that are being routed through a specific gateway in order to access a web page that is hosted internally on a separate subnet. I set up static routes on all of the computers, and they all work... except one. Here's what a route print -4 looks like for a working computer (Windows 7): =========================================================================== Interface List 14...xx xx xx xx xx xx ......Broadcom 802.11n Network Adapter 11...xx xx xx xx xx xx ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 17...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.xxx.xxx.230 10.xxx.xxx.94 20 10.zzz.zzz.0 255.255.255.0 10.xxx.xxx.147 10.xxx.xxx.94 21 10.xxx.xxx.0 255.255.255.0 On-link 10.xxx.xxx.94 276 10.xxx.xxx.94 255.255.255.255 On-link 10.xxx.xxx.94 276 10.xxx.xxx.255 255.255.255.255 On-link 10.xxx.xxx.94 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.xxx.xxx.94 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.xxx.xxx.94 276 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 10.zzz.zzz.0 255.255.255.0 10.xxx.xxx.147 1 =========================================================================== And here's a route print -4 from the station that doesn't work (also Windows 7): =========================================================================== Interface List 10...xx xx xx xx xx xx ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 16...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.xxx.xxx.230 10.xxx.xxx.132 276 10.zzz.zzz.0 255.255.255.0 10.xxx.xxx.147 10.xxx.xxx.132 21 10.xxx.xxx.0 255.255.255.0 On-link 10.xxx.xxx.132 276 10.xxx.xxx.132 255.255.255.255 On-link 10.xxx.xxx.132 276 10.xxx.xxx.255 255.255.255.255 On-link 10.xxx.xxx.132 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.xxx.xxx.132 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.xxx.xxx.132 276 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 10.zzz.zzz.0 255.255.255.0 10.xxx.xxx.147 1 =========================================================================== Both of these stations are running Windows 7. So essentially what I am trying to do here is route all traffic to the 10.zzz.zzz.0 subnet through the 10.xxx.xxx.147 gateway. Everything else should go through the 10.xxx.xxx.230 gateway. This is the intended behavior, and again it is working everywhere but that one station. I noticed that the Active Route metric costs differ between the two stations, but I am new to the routing table and I am not sure how that is impacting the behavior. I hope I have been able to explain the situation clearly. Any help would be much appreciated. I can provide any additional information if needed!

  Read the article

• SNTP, why do you mock me?!

  - by Matthew

  --- SOLVED SEE EDIT 5 --- My w2k3 pdc is configured as an authoritative time server. Other servers on the domain are able to sync with it if I manually specify it in the peer list. By if I try to sync from flags 'domhier', it wont resync; I get the error message The computer did not resync because no time data was available. I can only think that it is not querying the pdc. I also tried setting the registry as shown here (http://support.microsoft.com/kb/193825). But no luck (I have not restarted the server, I am hoping I wont have to since it is the pdc) If you would like any further information on my config, please let me know. Edit 1: I have set the w32time service config AnnouceFlags to 0x05 as documented here www.krr.org/microsoft/authoritative_time_servers.php and a number of other places. The PDC syncs to an external time source (ntp). I can get the stripchart on the client from the pdc no problems. The loginserver for the host I am trying to configure is shown as the pdc. Edit 2: The packet capture has revealed something interesting. The client is contacting the correct server, and getting a valid response but I still get the same error message. Here is the NTP excerpt from the client to the server Flags: 11.. .... = Leap Indicator: alarm condition (clock not synchronized) (3) ..01 1... = Version number: NTP Version 3 (3) .... .011 = Mode: client (3) Peer Clock Stratum: unspecified or unavailable (0) Peer Polling Interval: 10 (1024 sec) Peer Clock Precision: 0.015625 sec Root Delay: 0.0000 sec Root Dispersion: 1.0156 sec Reference Clock ID: NULL Reference Clock Update Time: Sep 1, 2010 05:29:39.8170 UTC Originate Time Stamp: NULL Receive Time Stamp: NULL Transmit Time Stamp: Nov 8, 2010 01:44:44.1450 UTC Key ID: DC080000 Here is the reply NTP excerpt from the server to the client Flags: 0x1c 00.. .... = Leap Indicator: no warning (0) ..01 1... = Version number: NTP Version 3 (3) .... .100 = Mode: server (4) Peer Clock Stratum: secondary reference (3) Peer Polling Interval: 10 (1024 sec) Peer Clock Precision: 0.00001 sec Root Delay: 0.1484 sec Root Dispersion: 0.1060 sec Reference Clock ID: 192.189.54.17 Reference Clock Update Time: Nov 8,2010 01:18:04.6223 UTC Originate Time Stamp: Nov 8, 2010 01:44:44.1450 UTC Receive Time Stamp: Nov 8, 2010 01:46:44.1975 UTC Transmit Time Stamp: Nov 8, 2010 01:46:44.1975 UTC Key ID: 00000000 Edit 3: dumpreg for paramters on pdc Value Name Value Type Value Data ------------------------------------------------------------------------ ServiceMain REG_SZ SvchostEntry_W32Time ServiceDll REG_EXPAND_SZ C:\WINDOWS\system32\w32time.dll NtpServer REG_SZ bhvmmgt01.domain.com,0x1 Type REG_SZ AllSync and config Value Name Value Type Value Data -------------------------------------------------------------------------- LastClockRate REG_DWORD 156249 MinClockRate REG_DWORD 155860 MaxClockRate REG_DWORD 156640 FrequencyCorrectRate REG_DWORD 4 PollAdjustFactor REG_DWORD 5 LargePhaseOffset REG_DWORD 50000000 SpikeWatchPeriod REG_DWORD 900 HoldPeriod REG_DWORD 5 LocalClockDispersion REG_DWORD 10 EventLogFlags REG_DWORD 2 PhaseCorrectRate REG_DWORD 7 MinPollInterval REG_DWORD 6 MaxPollInterval REG_DWORD 10 UpdateInterval REG_DWORD 100 MaxNegPhaseCorrection REG_DWORD -1 MaxPosPhaseCorrection REG_DWORD -1 AnnounceFlags REG_DWORD 5 MaxAllowedPhaseOffset REG_DWORD 300 FileLogSize REG_DWORD 10000000 FileLogName REG_SZ C:\Windows\Temp\w32time.log FileLogEntries REG_SZ 0-300 Edit 4: Here are some notables from the ntp log file on the pdc. ReadConfig: failed. Use default one 'TimeJumpAuditOffset'=0x00007080 DomainHierachy: we are now the domain root. ClockDispln: we're a reliable time service with no time source: LS: 0, TN: 864000000000, WAIT: 86400000 Edit 5: F&^%ING SOLVED! Ok so I was reading about people with similar problems, some mentioned w32time server settings applied by GPO, but I tested this early on and there were no settings applied to this service by gpo. Others said that the reporting software may not be picking up some old gpo settings applied. So I searched the registry for all w32time instaces. I came across an interesting key that indicated there may be some other ntp software running on the server. Sure enough, I look through the installed software list and there the little F*&%ER is. Uninstalled and now working like a dream. FFFFFFFUUUUUUUUUUUU

  Read the article

• Cisco Pix how to add an additional block of static ip addresses for nat?

  - by Scott Szretter

  I have a pix 501 with 5 static ip addresses. My isp just gave me 5 more. I am trying to figure out how to add the new block and then how to nat/open at least one of them to an inside machine. So far, I named a new interface "intf2", ip range is 71.11.11.58 - 62 (gateway should 71.11.11.57) imgsvr is the machine I want to nat to one of the (71.11.11.59) new ip addresses. mail (.123) is an example of a machine that is mapped to the current existing 5 ip block (96.11.11.121 gate / 96.11.11.122-127) and working fine. Building configuration... : Saved : PIX Version 6.3(4) interface ethernet0 auto interface ethernet0 vlan1 logical interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif vlan1 intf2 security1 enable password xxxxxxxxx encrypted passwd xxxxxxxxx encrypted hostname xxxxxxxPIX domain-name xxxxxxxxxxx no fixup protocol dns fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 no fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names ...snip... name 192.168.10.13 mail name 192.168.10.29 imgsvr object-group network vpn1 network-object mail 255.255.255.255 access-list outside_access_in permit tcp any host 96.11.11.124 eq www access-list outside_access_in permit tcp any host 96.11.11.124 eq https access-list outside_access_in permit tcp any host 96.11.11.124 eq 3389 access-list outside_access_in permit tcp any host 96.11.11.123 eq https access-list outside_access_in permit tcp any host 96.11.11.123 eq www access-list outside_access_in permit tcp any host 96.11.11.125 eq smtp access-list outside_access_in permit tcp any host 96.11.11.125 eq https access-list outside_access_in permit tcp any host 96.11.11.125 eq 10443 access-list outside_access_in permit tcp any host 96.11.11.126 eq smtp access-list outside_access_in permit tcp any host 96.11.11.126 eq https access-list outside_access_in permit tcp any host 96.11.11.126 eq 10443 access-list outside_access_in deny ip any any access-list inside_nat0_outbound permit ip 192.168.0.0 255.255.0.0 IPPool2 255.255.255.0 access-list inside_nat0_outbound permit ip 172.17.0.0 255.255.0.0 IPPool2 255.255.255.0 access-list inside_nat0_outbound permit ip 172.16.0.0 255.255.0.0 IPPool2 255.255.255.0 ...snip... access-list inside_access_in deny tcp any any eq smtp access-list inside_access_in permit ip any any pager lines 24 logging on logging buffered notifications mtu outside 1500 mtu inside 1500 ip address outside 96.11.11.122 255.255.255.248 ip address inside 192.168.10.15 255.255.255.0 ip address intf2 71.11.11.58 255.255.255.248 ip audit info action alarm ip audit attack action alarm pdm location exchange 255.255.255.255 inside pdm location mail 255.255.255.255 inside pdm location IPPool2 255.255.255.0 outside pdm location 96.11.11.122 255.255.255.255 inside pdm location 192.168.10.1 255.255.255.255 inside pdm location 192.168.10.6 255.255.255.255 inside pdm location mail-gate1 255.255.255.255 inside pdm location mail-gate2 255.255.255.255 inside pdm location imgsvr 255.255.255.255 inside pdm location 71.11.11.59 255.255.255.255 intf2 pdm logging informational 100 pdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 96.11.11.123 global (intf2) 3 interface global (intf2) 4 71.11.11.59 nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 mail 255.255.255.255 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 static (inside,outside) tcp 96.11.11.123 smtp mail smtp netmask 255.255.255.255 0 0 static (inside,outside) tcp 96.11.11.123 https mail https netmask 255.255.255.255 0 0 static (inside,outside) tcp 96.11.11.123 www mail www netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.124 ts netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.126 mail-gate2 netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.125 mail-gate1 netmask 255.255.255.255 0 0 access-group outside_access_in in interface outside access-group inside_access_in in interface inside route outside 0.0.0.0 0.0.0.0 96.11.11.121 1 route intf2 0.0.0.0 0.0.0.0 71.11.11.57 2 timeout xlate 0:05:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute floodguard enable ...snip... : end [OK] Thanks!

  Read the article

• Bugzilla : No SASL mechanism found

  - by niteshsinha

  I am using Bugzilla on windows 7. I am using the unofficial Bugzilla installer. I followed the steps accordingly and gave valid credentials wherever required. I open Bugzilla and try to create a new account , but i get the following error. Software error: No SASL mechanism found at C:/Program Files/Bugzilla/perl/perl/site/lib/Authen/SASL.pm line 77 at C:/Program Files/Bugzilla/perl/perl/lib/Net/SMTP.pm line 143 i ran checksetup.pl and found that Authen::SASL and SMTP both are available on my machine. The output of checksetup.pl is as follows. * This is Bugzilla 3.6.3 on perl 5.10.1 * Running on Win7 Build 7600 Checking perl modules... Checking for CGI.pm (v3.33) ok: found v3.49 Checking for Digest-SHA (any) ok: found v5.48 Checking for TimeDate (v2.21) ok: found v2.24 Checking for DateTime (v0.28) ok: found v0.53 Checking for DateTime-TimeZone (v0.79) ok: found v1.10 Checking for DBI (v1.41) ok: found v1.609 Checking for Template-Toolkit (v2.22) ok: found v2.22 Checking for Email-Send (v2.16) ok: found v2.198 Checking for Email-MIME (v1.861) ok: found v1.903 Checking for Email-MIME-Encodings (v1.313) ok: found v1.313 Checking for Email-MIME-Modifier (v1.442) ok: found v1.903 Checking for URI (any) ok: found v1.52 Checking available perl DBD modules... Checking for DBD-Pg (v1.45) ok: found v2.16.1 Checking for DBD-mysql (v4.00) ok: found v4.012 Checking for DBD-Oracle (v1.19) not found The following Perl modules are optional: Checking for GD (v1.20) ok: found v2.44 Checking for Chart (v2.1) ok: found v2.4.1 Checking for Template-GD (any) ok: found v1.56 Checking for GDTextUtil (any) ok: found v0.86 Checking for GDGraph (any) ok: found v1.44 Checking for XML-Twig (any) ok: found v3.34 Checking for MIME-tools (v5.406) ok: found v5.427 Checking for libwww-perl (any) ok: found v5.834 Checking for PatchReader (v0.9.4) ok: found v0.9.5 Checking for perl-ldap (any) ok: found v0.39 Checking for Authen-SASL (any) ok: found v2.15 Checking for RadiusPerl (any) ok: found v0.17 Checking for SOAP-Lite (v0.710.06) ok: found v0.710.10 Checking for JSON-RPC (any) ok: found v0.95 Checking for Test-Taint (any) ok: found v1.04 Checking for HTML-Parser (v3.40) ok: found v3.64 Checking for HTML-Scrubber (any) ok: found v0.08 Checking for Email-MIME-Attachment-Stripper (any) ok: found v1.316 Checking for Email-Reply (any) ok: found v1.202 Checking for TheSchwartz (any) not found Checking for Daemon-Generic (any) not found Checking for mod_perl (v1.999022) not found *********************************************************************** * OPTIONAL MODULES * *********************************************************************** * Certain Perl modules are not required by Bugzilla, but by * * installing the latest version you gain access to additional * * features. * * * * The optional modules you do not have installed are listed below, * * with the name of the feature they enable. Below that table are the * * commands to install each module. * *********************************************************************** * MODULE NAME * ENABLES FEATURE(S) * *********************************************************************** * TheSchwartz * Mail Queueing * * Daemon-Generic * Mail Queueing * * mod_perl * mod_perl * *********************************************************************** * Note For Windows Users * *********************************************************************** * In order to install the modules listed below, you first have to run * * the following command as an Administrator: * * * * ppm repo add theory58S http://cpan.uwinnipeg.ca/PPMPackages/10xx/ * * * Then you have to do (also as an Administrator): * * * * ppm repo up theory58S * * * * Do that last command over and over until you see "theory58S" at the * * top of the displayed list. * *********************************************************************** COMMANDS TO INSTALL OPTIONAL MODULES: TheSchwartz: ppm install TheSchwartz Daemon-Generic: ppm install Daemon-Generic mod_perl: ppm install mod_perl Reading ./localconfig... Checking for DBD-mysql (v4.00) ok: found v4.012 Checking for MySQL (v4.1.2) ok: found v5.1.44-community-log Removing existing compiled templates... Precompiling templates...done. Now that you have installed Bugzilla, you should visit the 'Parameters' page (linked in the footer of the Administrator account) to ensure it is set up as you wish - this includes setting the 'urlbase' option to the correct URL. Press any key to continue . . . Please tell me what should i do. Please note: i am running behind a corporate proxy , SSL/TLS is not used internally but i am giving the smtpUser and smtpPass also.

  Read the article

• Causes of sudden massive filesystem damage? ("root inode is not a directory")

  - by poolie

  I have a laptop running Maverick (very happily until yesterday), with a Patriot Torx SSD; LUKS encryption of the whole partition; one lvm physical volume on top of that; then home and root in ext4 logical volumes on top of that. When I tried to boot it yesterday, it complained that it couldn't mount the root filesystem. Running fsck, basically every inode seems to be wrong. Both home and root filesystems show similar problems. Checking a backup superblock doesn't help. e2fsck 1.41.12 (17-May-2010) lithe_root was not cleanly unmounted, check forced. Resize inode not valid. Recreate? no Pass 1: Checking inodes, blocks, and sizes Root inode is not a directory. Clear? no Root inode has dtime set (probably due to old mke2fs). Fix? no Inode 2 is in use, but has dtime set. Fix? no Inode 2 has a extra size (4730) which is invalid Fix? no Inode 2 has compression flag set on filesystem without compression support. Clear? no Inode 2 has INDEX_FL flag set but is not a directory. Clear HTree index? no HTREE directory inode 2 has an invalid root node. Clear HTree index? no Inode 2, i_size is 9581392125871137995, should be 0. Fix? no Inode 2, i_blocks is 40456527802719, should be 0. Fix? no Reserved inode 3 (<The ACL index inode>) has invalid mode. Clear? no Inode 3 has compression flag set on filesystem without compression support. Clear? no Inode 3 has INDEX_FL flag set but is not a directory. Clear HTree index? no .... Running strings across the filesystems, I can see there are what look like filenames and user data there. I do have sufficiently good backups (touch wood) that it's not worth grovelling around to pull back individual files, though I might save an image of the unencrypted disk before I rebuild, just in case. smartctl doesn't show any errors, neither does the kernel log. Running a write-mode badblocks across the swap lv doesn't find problems either. So the disk may be failing, but not in an obvious way. At this point I'm basically, as they say, fscked? Back to reinstalling, perhaps running badblocks over the disk, then restoring from backup? There doesn't even seem to be enough data to file a meaningful bug... I don't recall that this machine crashed last time I used it. At this point I suspect a bug or memory corruption caused it to write garbage across the disks when it was last running, or some kind of subtle failure mode for the SSD. What do you think would have caused this? Is there anything else you'd try?

  Read the article

• An error occured synchronizing windows with time.windows.com

  - by Killrawr

  Okay so I've tried stopping/registering the win32tm service on this Windows Server 2008 Enterprise Computer. C:\Users\Administrator>net stop w32time The Windows Time service is stopping. The Windows Time service was stopped successfully. C:\Users\Administrator>w32tm /unregister The following error occurred: Access is denied. (0x80070005) C:\Users\Administrator>w32tm /unregister W32Time successfully unregistered. C:\Users\Administrator>w32tm /register W32Time successfully registered. C:\Users\Administrator>net start w32time The Windows Time service is starting. The Windows Time service was started successfully. (Source : http://social.technet.microsoft.com/Forums/en-US/winserverDS/thread/9bdfc2cc-4775-4435-8868-57d214e1e3ba/) And I get this error from the Date and Time, Internet Time tab (After also following the steps here). I've even tried the Atomic Time Clock Worldtimeserver and I get the error The following error occurred: The specified module could not be found. (0x8007007E). I've also disabled the Windows Firewall, that might of been blocking the synchronization. I've done a file scan with sfc /scannow that came back with no errors. C:\Users\Administrator>sfc /scannow Beginning system scan. This process will take some time. Beginning verification phase of system scan. Verification 100% complete. Windows Resource Protection did not find any integrity violations. C:\Users\Administrator> But I'm not having much luck. Is there anyway lo possibly solve this? or is the time.windows.com servers unsupported? because the software is from 2008? (I really don't know :/), My ping result to time.windows.com C:\Users\Administrator>ping time.windows.com Pinging time.microsoft.akadns.net [65.55.21.22] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 65.55.21.22: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), And tracert result C:\Users\Administratortracert time.windows.com Tracing route to time.microsoft.akadns.net [65.55.21.24] over a maximum of 30 hops: 1 1 ms <1 ms <1 ms 192.168.1.1 2 32 ms 31 ms 32 ms be2-100.bras1wtc.wlg.vf.net.nz [203.109.129.113] 3 31 ms 32 ms 31 ms be5-100.ppnzwtc01.wlg.vf.net.nz.129.109.203.in-a ddr.arpa [203.109.129.114] 4 31 ms 31 ms 31 ms gi0-2-0-3.ppnzwtc01.wlg.vf.net.nz.180.109.203.in -addr.arpa [203.109.180.210] 5 31 ms 31 ms 30 ms gi0-2-0-3.ppnzwtc02.wlg.vf.net.nz [203.109.180.2 09] 6 167 ms 166 ms 166 ms ip-141.199.31.114.VOCUS.net.au [114.31.199.141] 7 175 ms 175 ms 175 ms microsoft.com.any2ix.coresite.com [206.223.143.1 43] 8 177 ms 180 ms 176 ms xe-7-0-2-0.by2-96c-1a.ntwk.msn.net [207.46.42.17 6] 9 205 ms 205 ms 204 ms xe-10-0-2-0.co1-96c-1b.ntwk.msn.net [207.46.45.3 1] 10 * * * Request timed out. 11 * * * Request timed out. 12 * * * Request timed out. 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 ^C And nslookup C:\Users\Administrator>nslookup time.windows.com Server: UnKnown Address: 192.168.1.1 Non-authoritative answer: Name: time.microsoft.akadns.net Address: 65.55.21.22 Aliases: time.windows.com

  Read the article

• CPU Utilization LAMP stack

  - by Max

  We've got an ec2 m2.4xlarge running Magento (centos 5.6, httpd 2.2, php 5.2.17 with eaccelerator 0.9.5.3, mysql 5.1.52). Right now we're getting a large traffic spike, and our top looks like this: top - 09:41:29 up 31 days, 1:12, 1 user, load average: 120.01, 129.03, 113.23 Tasks: 1190 total, 18 running, 1172 sleeping, 0 stopped, 0 zombie Cpu(s): 97.3%us, 1.8%sy, 0.0%ni, 0.5%id, 0.0%wa, 0.0%hi, 0.0%si, 0.4%st Mem: 71687720k total, 36898928k used, 34788792k free, 49692k buffers Swap: 880737784k total, 0k used, 880737784k free, 1586524k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2433 mysql 15 0 23.6g 4.5g 7112 S 564.7 6.6 33607:34 mysqld 24046 apache 16 0 411m 65m 28m S 26.4 0.1 0:09.05 httpd 24360 apache 15 0 410m 60m 25m S 26.4 0.1 0:03.65 httpd 24993 apache 16 0 410m 57m 21m S 26.1 0.1 0:01.41 httpd 24838 apache 16 0 428m 74m 20m S 24.8 0.1 0:02.37 httpd 24359 apache 16 0 411m 62m 26m R 22.3 0.1 0:08.12 httpd 23850 apache 15 0 411m 64m 27m S 16.8 0.1 0:14.54 httpd 25229 apache 16 0 404m 46m 17m R 10.2 0.1 0:00.71 httpd 14594 apache 15 0 404m 63m 34m S 8.4 0.1 1:10.26 httpd 24955 apache 16 0 404m 50m 21m R 8.4 0.1 0:01.66 httpd 24313 apache 16 0 399m 46m 22m R 8.1 0.1 0:02.30 httpd 25119 apache 16 0 411m 59m 23m S 6.8 0.1 0:01.45 httpd Questions: Would giving msyqld more memory help it cache queries and react faster? If so, how? Other than splitting mysql and php to separate servers (which we're about to do) is there anything else we could/should be doing? Thanks! UPDATE: Here's our my.cnf along with the output of mysqltuner. It looks like a cache problem. Thanks again! # cat /etc/my.cnf [client] port = **** socket = /var/lib/mysql/mysql.sock [mysqld] datadir=/mnt/persistent/mysql port=**** socket=/var/lib/mysql/mysql.sock key_buffer = 512M max_allowed_packet = 64M table_cache = 1024 sort_buffer_size = 8M read_buffer_size = 4M read_rnd_buffer_size = 2M myisam_sort_buffer_size = 64M thread_cache_size = 128M tmp_table_size = 128M join_buffer_size = 1M query_cache_limit = 2M query_cache_size= 64M query_cache_type = 1 max_connections = 1000 thread_stack = 128K thread_concurrency = 48 log-bin=mysql-bin server-id = 1 wait_timeout = 300 innodb_data_home_dir = /mnt/persistent/mysql/ innodb_data_file_path = ibdata1:10M:autoextend innodb_buffer_pool_size = 20G innodb_additional_mem_pool_size = 20M innodb_log_file_size = 64M innodb_log_buffer_size = 8M innodb_flush_log_at_trx_commit = 1 innodb_lock_wait_timeout = 50 innodb_thread_concurrency = 48 ft_min_word_len=3 [myisamchk] ft_min_word_len=3 key_buffer = 128M sort_buffer_size = 128M read_buffer = 2M write_buffer = 2M # ./mysqltuner.pl >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.52-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB +Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 2G (Tables: 26) [--] Data in InnoDB tables: 749M (Tables: 250) [!!] Total fragmented tables: 262 -------- Security Recommendations ------------------------------------------- -------- Performance Metrics ------------------------------------------------- [--] Up for: 31d 2h 30m 38s (680M q [253.371 qps], 2M conn, TX: 4825B, RX: 236B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 20.6G global + 15.1M per thread (1000 max threads) [OK] Maximum possible memory usage: 35.4G (51% of installed RAM) [OK] Slow queries: 0% (35K/680M) [OK] Highest usage of available connections: 53% (537/1000) [OK] Key buffer size / total MyISAM indexes: 512.0M/457.2M [OK] Key buffer hit rate: 100.0% (9B cached / 264K reads) [OK] Query cache efficiency: 42.3% (260M cached / 615M selects) [!!] Query cache prunes per day: 4384652 [OK] Sorts requiring temporary tables: 0% (1K temp sorts / 38M sorts) [!!] Joins performed without indexes: 100404 [OK] Temporary tables created on disk: 17% (7M on disk / 45M total) [OK] Thread cache hit rate: 99% (537 created / 2M connections) [!!] Table cache hit rate: 0% (1K open / 946K opened) [OK] Open file limit used: 9% (453/5K) [OK] Table locks acquired immediately: 99% (758M immediate / 758M locks) [OK] InnoDB data size / buffer pool: 749.3M/20.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 64M) join_buffer_size (> 1.0M, or always use indexes with joins) table_cache (> 1024)

  Read the article

• Postfix logs missing information on delivery status (postfix/smtp message)

  - by hegemon

  I noticed a problem with postfix logs, that information on some of emails delivery status is missing. The issue affects about 1% of emails. "Healthy" log: <server># grep 8EB992EFBB44 postfix_log/mail04.log Jun 5 03:09:29 mail04 postfix/smtpd[8537]: 8EB992EFBB44: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 03:09:29 mail04 postfix/cleanup[34349]: 8EB992EFBB44: message-id=<[email protected]> Jun 5 03:12:02 mail04 postfix/qmgr[76377]: 8EB992EFBB44: from=<[email protected]>, size=48845, nrcpt=1 (queue active) Jun 5 03:15:12 mail04 postfix/smtp[35058]: 8EB992EFBB44: to=<[email protected]>, relay=mx.baz.com[xxx.xxx.xxx.xxx]:25, conn_use=70, delay=343, delays=153/190/0/0.24, dsn=2.0.0, status=sent (250 ok) Jun 5 03:15:12 mail04 postfix/qmgr[76377]: 8EB992EFBB44: removed "Broken" log: <server># grep F3C362EF37CA postfix_log/mail04.log Jun 5 04:03:27 mail04 postfix/smtpd[39666]: F3C362EF37CA: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 04:03:27 mail04 postfix/cleanup[41287]: F3C362EF37CA: message-id=<[email protected]> Jun 5 04:03:28 mail04 postfix/qmgr[76377]: F3C362EF37CA: from=<[email protected]>, size=48892, nrcpt=1 (queue active) ** here should be a log line from postfix/smtp but there is none ** Jun 5 04:03:29 mail04 postfix/qmgr[76377]: F3C362EF37CA: removed Background information: system: FreeBSD xxx.xxx.xxx 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Thu Feb 17 02:41:51 UTC 2011 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 Postfix is installed inside jail. Logs are on the same machine, log dir is mounted thru nullfs. The site has spikes of heavy load, causing disks (local) to run at 100%. Update The log is rotated daily, current size is ~ 500MB. I made a test by queuing 99000 messages to same destination (in order to rule out dns/network/mx issues). 5715 messages don't have any DSN record. Failed messages queue time is spread evenly over time, i don't see any time-bound issues. Some undelivered emails: envelopeid | processed_time --------------+---------------------------- 8D7652EF3BAE | 2012-06-06 13:19:11.072715 DD53A2EF3C5C | 2012-06-06 13:33:24.374783 8C52F2EF4E3F | 2012-06-06 13:39:15.810616 BBC572EF525C | 2012-06-06 13:44:22.762812 E95822EF54D1 | 2012-06-06 13:52:01.134533 839DD2EF4FBB | 2012-06-06 14:13:48.511236 017EE2EF6234 | 2012-06-06 15:04:48.618963 Those are a few picks, such records of undelivered email occur almost every second. <server># egrep '(8D7652EF3BAE|BBC572EF525C|017EE2EF6234)' mail04.log Jun 6 13:19:10 mail04 postfix/smtpd[20350]: 8D7652EF3BAE: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:19:10 mail04 postfix/cleanup[21024]: 8D7652EF3BAE: message-id=<[email protected]> Jun 6 13:19:10 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: from=<[email protected]>, size=63718, nrcpt=1 (queue active) Jun 6 13:19:11 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: removed Jun 6 13:44:22 mail04 postfix/smtpd[20346]: BBC572EF525C: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:44:22 mail04 postfix/cleanup[24811]: BBC572EF525C: message-id=<[email protected]> Jun 6 13:44:22 mail04 postfix/qmgr[7939]: BBC572EF525C: from=<[email protected]>, size=63758, nrcpt=1 (queue active) Jun 6 15:04:49 mail04 postfix/smtpd[20344]: 017EE2EF6234: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 15:04:49 mail04 postfix/cleanup[35585]: 017EE2EF6234: message-id=<[email protected]> Jun 6 15:04:49 mail04 postfix/qmgr[7939]: 017EE2EF6234: from=<[email protected]>, size=63706, nrcpt=1 (queue active) <server># <server># find /var/spool/postfix/active/ -type f -print | wc -l 1 <server># IMPORTANT: As you can see above some of emails doesn't event have the removed line.

  Read the article

• Cisco 678 Will Not Work using PPPoE - Possibly Because I Configured it Incorrectly..?

  - by Brian Stinar

  I am attempting to configure a Cisco 678 because I am totally sick on my Actiontec. However, I am running into some problems. It seems as though the Cisco is able to train the line, but I am unable to ping out. I am all right at programming, but still learning a lot when it comes to being a system administrator. I apologize in advance if I did something ridiculous, or am attempting to configure this device to do something it was not designed to do. It is almost like I am not correctly configuring the device to grab it's IP using PPPoA (like my Actiontec.) The output from "show running" (below) makes me think this too. Below are the commands I ran in order to configure this: # en # set nvram erase # write # reboot # en # set nat enable # set dhcp server enable # set PPP wan0-0 ipcp 0.0.0.0 # set ppp wan0-0 dns 0.0.0.0 # set PPP wan0-0 login xxxxx // My actual login # set PPP wan0-0 password yyyyy // My actual password # set PPP restart enabled # set int wan0-0 close # set int wan0-0 vpi 0 # set int wan0-0 vci 32 # set int wan0-0 open # write # reboot Here is the output from a few commands I thought could provide some useful information: cbos#ping 74.125.224.113 Sending 1 8 byte ping(s) to 74.125.224.113 every 2 second(s) Request timed out cbos#show version Cisco Broadband Operating System CBOS (tm) 678 Software (C678-I-M), Version v2.4.9 - Release Software Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Nov 17 2004 15:26:29 DMT FULL firmware version G96 NVRAM image at 0x1030f000 cbos#show errors - Current Error Messages - ## Ticks Module Level Message 0 000:00:00:00 PPP Info IPCP Open Event on wan0-0 1 000:00:00:14 ATM Info Wan0 Up 2 000:00:00:14 PPP Info PPP Up Event on wan0-0 3 000:00:01:54 PPP Info PPP Down Event on wan0-0 Total Number of Error Messages: 4 cbos#show interface wan0 wan0 ADSL Physical Port Line Trained Actual Configuration: Overhead Framing: 3 Trellis Coding: Enabled Standard Compliance: T1.413 Downstream Data Rate: 1184 Kbps Upstream Data Rate: 928 Kbps Interleave S Downstream: 4 Interleave D Downstream: 16 Interleave R Downstream: 16 Interleave S Upstream: 4 Interleave D Upstream: 8 Interleave R Upstream: 16 Modem Microcode: G96 DSP version: 0 Operating State: Showtime/Data Mode Configured: Echo Cancellation: Disabled Overhead Framing: 3 Coding Gain: Auto TX Power Attenuation: 0dB Trellis Coding: Enabled Bit Swapping: Disabled Standard Compliance: T1.413 Remote Standard Compliance: T1.413 Tx Start Bin: 0x6 Tx End Bin: 0x1f Data Interface: Utopia L1 Status: Local SNR Margin: 19.0dB Local Coding Gain: 7.5dB Local Transmit Power: 12.5dB Local Attenuation: 46.0dB Remote Attenuation: 31.0dB Local Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 2 No Cell Delineation Interleaved: 0 Out of Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 Remote Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 1 No Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 0, VCI 32) is configured. ScalaRate set to Auto AAL 5 UBR Traffic IP Port Enabled cbos#show running Warning: traffic may pause while NVRAM is being accessed [[ CBOS = Section Start ]] NSOS MD5 Enable Password = XXXX NSOS MD5 Root Password = XXXX NSOS MD5 Commander Password = XXXX [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, "XXXX" PPP Port User Password = 00, XXXX PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable ,IP,0.0.0.0 PPP Port Option = 00, IPCP,Primary DNS Server,129,Auto,Negotiation Not Required, Negotiable,IP,0.0.0.0 PPP Port Option = 00, IPCP,Secondary DNS Server,131,Auto,Negotiation Not Require d,Negotiable,IP,0.0.0.0 [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 0, 32, 0 [[ DHCP = Section Start ]] DHCP Server = enabled [[ IP Routing = Section Start ]] IP NAT = enabled [[ WEB = Section Start ]] WEB = enabled cbos# wtf...? Thank you all very much for taking the time to read this, and the help.

  Read the article

• e2fsck / resize2fs problems

  - by BlakBat

  I've got 6 drives (each 1.5T, all same model and firmware revision) that are part of a RAID5 array. The RAID5 makes a LVM volume group and a logical group. The latter contains only one ext3 partition. I've recently ran: e2fsck -f /dev/vg03/lv01 && resize2fs -M /dev/vg03/lv01 which exited without an error. Now when I try to mount /dev/vg03/lv01 I get: EXT3-fs error (device dm-0): ext3_check_descriptors: Block bitmap for group 30533 not in group (block 1000532368)! EXT3-fs: group descriptors corrupted! How do I get out of this predicament? This is all the info I can currently give you: fdisk -l /dev/sd[cdefgh] shows (correctly) that they are "Linux raid autodetect" but fdisk now shows: fdisk -l /dev/md0 Disk /dev/md0: 7501.5 GB, 7501495664640 bytes ... Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table (instead of a LVM type partition) fdisk -l /dev/vg03/lv01 Disk /dev/vg03/lv01: 7501.5 GB, 7501491732480 bytes ... Disk identifier: 0x00000000 Disk /dev/vg03/lv01 doesn't contain a valid partition table (instead of a ext3 type partition) I've tried: e2fsck -fy /dev/vg03/lv01 e2fsck 1.41.12 (17-May-2010) e2fsck: Group descriptors look bad... trying backup blocks... Block bitmap for group 30533 is not in group. (block 1000532368) Relocate? yes Inode bitmap for group 30533 is not in group. (block 1000532369) Relocate? yes Pass 1: Checking inodes, blocks, and sizes Relocating group 30533's block bitmap to 1000524246... Error allocating 1 contiguous block(s) in block group 30533 for inode bitmap: Could not allocate block in ext2 filesystem e2fsck: aborted Extra information I can give you: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active (auto-read-only) raid5 sdg1[0] sdh1[5] sdf1[4] sde1[3] sdc1[2] sdd1[1] 7325679360 blocks level 5, 128k chunk, algorithm 2 [6/6] [UUUUUU] bitmap: 1/175 pages [4KB], 4096KB chunk unused devices: Lastly, all smartctl tests (short and extendend) showed no errors on any of the disks. Should I try to resize2fs to grow /dev/vg03/lv01 and redo a e2fsck ? Should I cfdisk /dev/md0 and /dev/vg03/lv01 back to their real types? Thanks in advance for all and any help. 2011-09-20 UPDATE I issued the following commands and was able to remount the partition, but by viewing the size (df) of before and after, it seems that 1Tb of data have gone missing. By checking the MD5SUMS (from an old backup) of some files with the "same" files from the remounted partition, some errors have been detected. Commands issued to remount the partition were: dumpe2fs /dev/vg03/lv01 Block count: 1000491435<br /> Block size: 4096<br /> tune2fs -O ^has_journal /dev/vg03/lv01 resize2fs -p /dev/vg03/lv01 dumpe2fs /dev/vg03/lv01 Block count: 1831418880<br /> Block size: 4096<br /> mount -o ro,noatime /dev/vg03/lv01 /mnt/raid OK... but files have been damaged / gone missing.

  Read the article

• How to use more than 3 virtual disks in Linux using CentOS and XenServer

  - by 010110110101

  I've attached 5 virtual disks to a Virtual Machine in Citrix XenServer. The VM has the xs-tools installed. Initially it said that it couldn't add so many disks. After I installed the xs-tools, it let me add all the disks. But /dev doesn't show all the disks. It shows these: /dev/xvda /dev/xvdb /dev/xvdc /dev/cdrom Perhaps it is bound by the limits of an IDE bus? (3 disks + CD-ROM) If so, how does one change the VM to use SCSI? Edit: According to the documentation: 2.6.3. VM Block Devices In the PV Linux case, block devices are passed through as PV devices. XenServer does not attempt to emulate SCSI or IDE, but instead provides a more suitable interface in the virtual environment in the form of xvd* devices. It is also possible to get an sd* device using the same mechanism, where the PV driver inside the VM takes over the SCSI device namespace. This is not desirable so it is best to use xvd* where possible for PV guests (this is the default for Debian and RHEL). For Windows or other fully virtualized guests, XenServer emulates an IDE bus in the form of an hd* device. When using Windows, installing the Citrix Tools for Virtual Machines installs a special PV driver that works in a similar way to Linux, except in the fully virtualized environment. Still, with 5 virtual disks attached, I don't see the other xvd devices. Edit #2: (attached requested info) Host Machine: XenServer 6.1 Linux version 2.6.32.43-0.4.1.xs1.6.10.777.170770xen (geeko@buildhost) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-51)) #1 SMP Wed Apr 17 05:52:03 EDT 2013 Guest Machine: CentOS release 6.4 (Final) Linux version 2.6.32-358.6.2.el6.x86_64 ([email protected]) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Thu May 16 20:59:36 UTC 2013 Output of 'fdisk -l' on Guest Machine: Note, the disk beyond the first 3 attached are not displaying -- there should be 4 100GB disks. (There are a total of 5 disks displayed in XenCenter -- 16GB, 100GB, 100GB, 100GB, 100GB) Disk /dev/xvdb: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xfb6c95b9 Device Boot Start End Blocks Id System /dev/xvdb1 1 13054 104856223+ 83 Linux Disk /dev/xvda: 17.2 GB, 17179869184 bytes 255 heads, 63 sectors/track, 2088 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e5f41 Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2089 16264192 8e Linux LVM Disk /dev/xvdc: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xed249ced Device Boot Start End Blocks Id System /dev/xvdc1 1 13054 104856223+ 83 Linux Disk /dev/mapper/vg_blue-lv_root: 14.6 GB, 14571012096 bytes 255 heads, 63 sectors/track, 1771 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_blue-lv_swap: 2080 MB, 2080374784 bytes 255 heads, 63 sectors/track, 252 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 I see that the Linux versions say SMP. The Guest VM doesn't say "xen" in the name. However, I have already run yum install kernel-xen. Could be a clue?

  Read the article

• Where's my memory?! Nginx + PHP-FPM front end webserver slows to a crawl...

  - by incredimike

  I'm not sure if I have a problem with a memory leak (as my hosting company suggests), or if we both need to read http://linuxatemyram.com. Maybe you clever people can help us out? This is a front-end webserver VM running essentially only nginx & php-fpm on RHEL 5.5. This server is powering Magento, a PHP eCommerce thinggy. The server is running in a shared environment, but we're changing that soon. Anyway.. after a reboot the server runs just fine, but within a day it will grind itself into nothingness. Pages will take literally 2 minutes to load, CPU spikes like crazy, etc.. The console is even sluggish when I SSH in. It's like my whole server is being brought to its knees. I've also been monitoring the DB server via top and tcpdumping incoming traffic. The DB stays idle for a good portion of that "slow" load time. When i start seeing queries coming from the front-end server, the page loads soon afterward. Here are some stats after me logging in during a slow-down, after restarting php-fpm: [mike@front01 ~]$ free -m total used free shared buffers cached Mem: 5963 5217 745 0 192 314 -/+ buffers/cache: 4711 1252 Swap: 4047 4 4042 [mike@front01 ~]$ top top - 11:38:55 up 2 days, 1:01, 3 users, load average: 0.06, 0.17, 0.21 Tasks: 131 total, 1 running, 130 sleeping, 0 stopped, 0 zombie Cpu0 : 0.0%us, 0.3%sy, 0.0%ni, 99.3%id, 0.3%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 0.3%us, 0.0%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 6106800k total, 5361288k used, 745512k free, 199960k buffers Swap: 4144728k total, 4976k used, 4139752k free, 328480k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31806 apache 15 0 601m 120m 37m S 0.0 2.0 0:22.23 php-fpm 31805 apache 15 0 549m 66m 31m S 0.0 1.1 0:14.54 php-fpm 31809 apache 16 0 547m 65m 32m S 0.0 1.1 0:12.84 php-fpm 32285 apache 15 0 546m 63m 33m S 0.0 1.1 0:09.22 php-fpm 32373 apache 15 0 546m 62m 32m S 0.0 1.1 0:09.66 php-fpm 31808 apache 16 0 543m 60m 35m S 0.0 1.0 0:18.93 php-fpm 31807 apache 16 0 533m 49m 30m S 0.0 0.8 0:08.93 php-fpm 32092 apache 15 0 535m 48m 27m S 0.0 0.8 0:06.67 php-fpm 4392 root 18 0 194m 10m 7184 S 0.0 0.2 0:06.96 cvd 4064 root 15 0 154m 8304 4220 S 0.0 0.1 3:55.57 snmpd 4394 root 15 0 119m 5660 2944 S 0.0 0.1 0:02.84 EvMgrC 31804 root 15 0 519m 5180 932 S 0.0 0.1 0:00.46 php-fpm 4138 ntp 15 0 23396 5032 3904 S 0.0 0.1 0:02.38 ntpd 643 nginx 15 0 95276 4408 1524 S 0.0 0.1 0:01.15 nginx 5131 root 16 0 90128 3340 2600 S 0.0 0.1 0:01.41 sshd 28467 root 15 0 90128 3340 2600 S 0.0 0.1 0:00.35 sshd 32602 root 16 0 90128 3332 2600 S 0.0 0.1 0:00.36 sshd 1614 root 16 0 90128 3308 2588 S 0.0 0.1 0:00.02 sshd 2817 root 5 -10 7216 3140 1724 S 0.0 0.1 0:03.80 iscsid 4161 root 15 0 66948 2340 800 S 0.0 0.0 0:10.35 sendmail 1617 nicole 17 0 53876 2000 1516 S 0.0 0.0 0:00.02 sftp-server ... Is there anything else I should be looking at, or any more information that might be useful? I'm just a developer, but the slowdowns on this system worry me and make it hard to do my work.. Help me out, ServerFault!

  Read the article

• Outlook Web Access, reverse proxy and browser

  - by M'vy

  Hi SF'ers! We recently moved an exchange server behind a reverse proxy due to the loss of a public IP. I've managed to configure the reverse proxy (httpd proxy_http). But there is a problem for the SSL configuration. When accessing the OWA interface with Firefox, all is ok and working. When accessing with MSIE or Chrome, they do not retrieve the good SSL Certificate. I think this is due to the multiples virtual host for httpd. Is there a workaround to make sure MSIE/Chrome request the certificate for the good domain name like FF does? Already tested with the SSL virtual host : SetEnvIf User-Agent ".*MSIE.*" value BrowserMSIE Header unset WWW-Authenticate Header add WWW-Authenticate "Basic realm=exchange.domain.com" A: ProxyPreserveHost On also: BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 Or: SetEnvIf User-Agent ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 And lots of ProxyPassand ProxyReversePath on /exchweb /exchange /public etc... And it still don't seem to work. Any clue? Thanks. Edit 1: Precision of versions # openssl version OpenSSL 0.9.8k-fips 25 Mar 2009 /usr/sbin/httpd -v Server version: Apache/2.2.11 (Unix) Server built: Mar 17 2009 09:15:10 Browser versions : MSIE : 8.0.6001 Opera: Version 11.01 Revision 1190 Firefox: 3.6.15 Chrome: 10.0.648.151 Operating System: Windows Vista 32bits. They are all SNI compliant, I've tested them this afternoon https://sni.velox.ch/ You're right Shane Madden, I have multiple sites on the same public IP (and same port as well). The server itself is just a reverse proxy, that rewrite addresses to internal servers. The default host is a dev site, configure with the certificate that does not match the OWA (of course... would have been to easy) <VirtualHost *:443> ServerName dev2.domain.com ServerAdmin [email protected] CustomLog "| /usr/sbin/rotatelogs /var/log/httpd/access-%y%m%d.log 86400" combined ErrorLog "| /usr/sbin/rotatelogs /var/log/httpd/error-%y%m%d.log 86400" LogLevel warn RewriteEngine on SetEnvIfNoCase X-Forwarded-For .+ proxy=yes SSLEngine on SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL:+SSLv3 SSLCertificateFile /etc/httpd/ssl/domain.com.crt SSLCertificateKeyFile /etc/httpd/ssl/domain.com.key RewriteCond %{HTTP_HOST} dev2\.domain\.com RewriteRule ^/(.*)$ http://dev2.domain.com/$1 [L,P] </VirtualHost> The certificate of domain is a *.domain.com The second vHost is : <VirtualHost *:443> ServerName exchange.domain2.com ServerAdmin [email protected] CustomLog "| /usr/sbin/rotatelogs /var/log/httpd/exchange/access-%y%m%d.log 86400" combined ErrorLog "| /usr/sbin/rotatelogs /var/log/httpd/exchange/error-%y%m%d.log 86400" LogLevel warn SSLEngine on SSLProxyEngine On SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL:+SSLv3 SSLCertificateFile /etc/httpd/ssl/exchange.pem SSLCertificateKeyFile /etc/httpd/ssl/exchange.key RewriteEngine on SetEnvIfNoCase X-Forwarded-For .+ proxy=yes RewriteCond %{HTTP_HOST} exchange\.domain2\.com RewriteRule ^/(.*)$ https://exchange.domain2.com/$1 [L,P] </VirtualHost> and it's certificate is exchange.domain2.com only. I presume the SNI is somewhere not activated on my server. The versions of openssl and apache seams to be ok for the SNI support. The only thing I do not know is if httpd has been compile with the good options. (I assume it's a fedora packet).

  Read the article

• Email from my new vps is marked as spam

  - by Chriswede

  I got a new vps from x10vps (x10hosting) and set up the domain via cloudflare. This is what the email looks like: Delivered-To: [email protected] Received: by 10.64.19.240 with SMTP id i16csp357708iee; Tue, 9 Oct 2012 01:29:48 -0700 (PDT) Received: by 10.50.57.130 with SMTP id i2mr908846igq.56.1349771387599; Tue, 09 Oct 2012 01:29:47 -0700 (PDT) Return-Path: <[email protected]> Received: from power.SOURCEAPE.COM ([198.91.90.116]) by mx.google.com with ESMTPS id v8si25630942ica.46.2012.10.09.01.29.46 (version=TLSv1/SSLv3 cipher=OTHER); Tue, 09 Oct 2012 01:29:47 -0700 (PDT) Received-SPF: temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) client-ip=198.91.90.116; Authentication-Results: mx.google.com; spf=temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) [email protected] Received: from nk11p03mm-asmtp010.mac.com ([17.158.232.169]:54276) by power.SOURCEAPE.COM with esmtp (Exim 4.80) (envelope-from <[email protected]>) id 1TLVBD-0004Ig-1Y for [email protected]; Tue, 09 Oct 2012 12:28:43 +0400 I then tried to enable SPF and DKIM and got following massage In order to ensure that SPF or DKIM takes effect, you must confirm that this server is an authoritative nameserver for chvw.de. If you need help, contact your hosting provider. Status: Enabled Warning: cPanel is unable to verify that this server is an authoritative nameserver for chvw.de. [?] and the email header now looks like this: Delivered-To: [email protected] Received: by 10.50.183.227 with SMTP id ep3csp14506igc; Tue, 9 Oct 2012 01:55:23 -0700 (PDT) Received: by 10.50.40.133 with SMTP id x5mr992934igk.32.1349772923717; Tue, 09 Oct 2012 01:55:23 -0700 (PDT) Return-Path: <[email protected]> Received: from power.SOURCEAPE.COM ([198.91.90.116]) by mx.google.com with ESMTPS id ng8si25688859icb.42.2012.10.09.01.55.23 (version=TLSv1/SSLv3 cipher=OTHER); Tue, 09 Oct 2012 01:55:23 -0700 (PDT) Received-SPF: temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) client-ip=198.91.90.116; Authentication-Results: mx.google.com; spf=temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) [email protected]; dkim=neutral (bad format) [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=chvw.de; s=default; h=Message-ID:Subject:To:From:Date:Content-Transfer-Encoding:Content-Type:MIME-Version; bh=iugsx3Lx0KnqjR7dj3wyQHnJ9pe/z3ntYEVk80k8rx4=; b=IrYsCtHdoPubXVOvLqxd7sLE/TyQTS5P3OrEg5SSUSKnQQcQ/fWWyBrmsrgkFSsw6jCmmRWMDR09vH5bQRpFPMA57B7pf8QRKhwXOWFBV+GnVUqICsfRjnNPvhx/lNp5; Received: from localhost ([127.0.0.1]:46539 helo=direct.chvw.de) by power.SOURCEAPE.COM with esmtpa (Exim 4.80) (envelope-from <[email protected]>) id 1TLVb0-0004dZ-Kd for [email protected]; Tue, 09 Oct 2012 12:55:22 +0400

  Read the article

• FFMPEG dropping frames while encoding JPEG sequence at color change

  - by Matt

  I'm trying to put together a slide show using imagemagick and FFMPEG. I use imagemagick to expand a single photo into 30fps video (imagemagick also handles things like putting some text captions on the frames along the way). When I go to let ffmpeg digest it into a video it clips along nicely on the color parts of the video, but when it gets to a black and white section it reports "frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703" and drops every frame of video until it hits something with color. As you can imagine this results in entire photos being removed from the slideshow. Here is my latest dump... ffmpeg -y -r 30 -i "teststream/%06d.jpg" -c:v libx264 -r 30 newffmpeg.mp4 ffmpeg version git-2012-12-10-c3bb333 Copyright (c) 2000-2012 the FFmpeg developers built on Dec 10 2012 22:02:04 with gcc 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) configuration: --enable-gpl --enable-libfaac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 12.100 / 52. 12.100 libavcodec 54. 79.101 / 54. 79.101 libavformat 54. 49.100 / 54. 49.100 libavdevice 54. 3.102 / 54. 3.102 libavfilter 3. 26.101 / 3. 26.101 libswscale 2. 1.103 / 2. 1.103 libswresample 0. 17.102 / 0. 17.102 libpostproc 52. 2.100 / 52. 2.100 Input #0, image2, from 'teststream/%06d.jpg': Duration: 00:12:02.80, start: 0.000000, bitrate: N/A Stream #0:0: Video: mjpeg, yuvj444p, 720x480 [SAR 72:72 DAR 3:2], 25 fps, 25 tbr, 25 tbn, 25 tbc [libx264 @ 0x3450140] using SAR=1/1 [libx264 @ 0x3450140] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 [libx264 @ 0x3450140] profile High, level 3.0 [libx264 @ 0x3450140] 264 - core 129 r2 1cffe9f - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=12 lookahead_threads=2 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=23.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'newffmpeg.mp4': Metadata: encoder : Lavf54.49.100 Stream #0:0: Video: h264 ([33][0][0][0] / 0x0021), yuvj420p, 720x480 [SAR 1:1 DAR 3:2], q=-1--1, 15360 tbn, 30 tbc Stream mapping: Stream #0:0 - #0:0 (mjpeg - libx264) Press [q] to stop, [?] for help Input stream #0:0 frame changed from size:720x480 fmt:yuvj444p to size:720x480 fmt:yuvj422p Input stream #0:0 frame changed from size:720x480 fmt:yuvj422p to size:720x480 fmt:yuvj444pp=584 frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703 video:5179kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.472425% [libx264 @ 0x3450140] frame I:9 Avg QP:20.10 size: 33933 [libx264 @ 0x3450140] frame P:636 Avg QP:24.12 size: 6737 [libx264 @ 0x3450140] frame B:1385 Avg QP:27.04 size: 514 [libx264 @ 0x3450140] consecutive B-frames: 2.5% 15.2% 13.2% 69.2% [libx264 @ 0x3450140] mb I I16..4: 8.3% 80.3% 11.5% [libx264 @ 0x3450140] mb P I16..4: 1.5% 2.5% 0.2% P16..4: 41.7% 18.0% 10.3% 0.0% 0.0% skip:25.9% [libx264 @ 0x3450140] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 26.6% 0.6% 0.1% direct: 0.2% skip:72.3% L0:35.0% L1:60.3% BI: 4.7% [libx264 @ 0x3450140] 8x8 transform intra:64.1% inter:75.1% [libx264 @ 0x3450140] coded y,uvDC,uvAC intra: 51.6% 78.0% 43.7% inter: 10.6% 14.9% 2.1% [libx264 @ 0x3450140] i16 v,h,dc,p: 29% 19% 6% 46% [libx264 @ 0x3450140] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 23% 15% 17% 5% 9% 10% 7% 8% 6% [libx264 @ 0x3450140] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 31% 18% 11% 5% 9% 10% 6% 6% 4% [libx264 @ 0x3450140] i8c dc,h,v,p: 46% 18% 24% 12% [libx264 @ 0x3450140] Weighted P-Frames: Y:20.1% UV:18.7% [libx264 @ 0x3450140] ref P L0: 59.2% 23.2% 13.1% 4.3% 0.2% [libx264 @ 0x3450140] ref B L0: 88.7% 8.3% 3.0% [libx264 @ 0x3450140] ref B L1: 95.0% 5.0% [libx264 @ 0x3450140] kb/s:626.88 Received signal 2: terminating. One last note: If I remove the -r 30 from the input and output it works flawlessly. I have no idea why the -r 30 is causing it to freak out.

  Read the article

• NPM not installing dependencies?

  - by neezer

  Having trouble getting NPM to install dependencies with npm install -d in my project directory with a defined package.json file. Here's my package.json: https://gist.github.com/3068312 And after wiping my project root's node modules folder (rm -rf node_modules), I run npm install -d in my project root and am greeted with this: (ssh) /vagrant git:master ? npm install -d npm info it worked if it ends with ok npm info using [email protected] npm info using [email protected] npm info preinstall [email protected] npm http GET https://registry.npmjs.org/sinon npm http GET https://registry.npmjs.org/underscore npm http GET https://registry.npmjs.org/mocha npm http GET https://registry.npmjs.org/request npm http 304 https://registry.npmjs.org/sinon npm http 304 https://registry.npmjs.org/underscore npm http 304 https://registry.npmjs.org/mocha npm http 304 https://registry.npmjs.org/request npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info into /vagrant [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info installOne [email protected] npm info unbuild /vagrant/node_modules/underscore npm info unbuild /vagrant/node_modules/mocha npm info unbuild /vagrant/node_modules/sinon npm info unbuild /vagrant/node_modules/request npm ERR! error installing [email protected] npm info unbuild /vagrant/node_modules/underscore npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/vagrant/node_modules/underscore' npm ERR! Error: ENOENT, no such file or directory '/vagrant/node_modules/underscore/package.json' npm ERR! You may report this log at: npm ERR! <http://bugs.debian.org/npm> npm ERR! or use npm ERR! reportbug --attach /vagrant/npm-debug.log npm npm ERR! npm ERR! System Linux 3.2.0-23-generic npm ERR! command "node" "/usr/bin/npm" "install" "-d" npm ERR! cwd /vagrant npm ERR! node -v v0.6.12 npm ERR! npm -v 1.1.4 npm ERR! path /vagrant/node_modules/underscore/package.json npm ERR! code ENOENT npm ERR! message ENOENT, no such file or directory '/vagrant/node_modules/underscore/package.json' npm ERR! errno {} npm ERR! error installing [email protected] npm info unbuild /vagrant/node_modules/request npm ERR! error rolling back [email protected] Error: UNKNOWN, unknown error '/vagrant/node_modules/request' npm ERR! npm ERR! Additional logging details can be found in: npm ERR! /vagrant/npm-debug.log npm not ok If I rerun npm install -d, the error changes to whatever the next package is... if I keep running it it over and over again, it eventually doesn't complain anymore and outputs: (ssh) /vagrant git:master ? npm install -d npm info it worked if it ends with ok npm info using [email protected] npm info using [email protected] npm info preinstall [email protected] npm info build /vagrant npm info linkStuff [email protected] npm info install [email protected] npm info postinstall [email protected] npm info ok However, none of the dependencies for any of these packages get installed. For instance, cheerio has a few dependencies, so when I try running my test suite, I'm greeted with: (ssh) /vagrant git:master ? mocha --compilers coffee:coffee-script --watch spec/* node.js:201 throw e; // process.nextTick error, or 'error' event on first tick ^ Error: Cannot find module 'cheerio-select' at Function._resolveFilename (module.js:332:11) at Function._load (module.js:279:25) at Module.require (module.js:354:17) What gives? I'm on Ubuntu Precise64 in a Vagrant virtual box.

  Read the article

• iptables rule(s) to send openvpn traffic from clients over an sshuttle tunnel?

  - by Sam Martin

  I have an Ubuntu 12.04 box with OpenVPN. The VPN is working as expected -- clients can connect, browse the Web, etc. The OpenVPN server IP is 10.8.0.1 on tun0. On that same box, I can use sshuttle to tunnel into another network to access a Web server on 10.10.0.9. sshuttle does its magic using the following iptables commands: iptables -t nat -N sshuttle-12300 iptables -t nat -F sshuttle-12300 iptables -t nat -I OUTPUT 1 -j sshuttle-12300 iptables -t nat -I PREROUTING 1 -j sshuttle-12300 iptables -t nat -A sshuttle-12300 -j REDIRECT --dest 10.10.0.0/24 -p tcp --to-ports 12300 -m ttl ! --ttl 42 iptables -t nat -A sshuttle-12300 -j RETURN --dest 127.0.0.0/8 -p tcp Is it possible to forward traffic from OpenVPN clients over the sshuttle tunnel to the remote Web server? I'd ultimately like to be able to set up any complicated tunneling on the server, and have relatively "dumb" clients (iPad, etc.) be able to access the remote servers via OpenVPN. Below is a basic diagram of the scenario: [Edit: added output from the OpenVPN box] $ sudo iptables -nL -v -t nat Chain PREROUTING (policy ACCEPT 1498 packets, 252K bytes) pkts bytes target prot opt in out source destination 1512 253K sshuttle-12300 all -- * * 0.0.0.0/0 0.0.0.0/0 Chain INPUT (policy ACCEPT 322 packets, 58984 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 584 packets, 43241 bytes) pkts bytes target prot opt in out source destination 587 43421 sshuttle-12300 all -- * * 0.0.0.0/0 0.0.0.0/0 Chain POSTROUTING (policy ACCEPT 589 packets, 43595 bytes) pkts bytes target prot opt in out source destination 1175 76298 MASQUERADE all -- * eth0 10.8.0.0/24 0.0.0.0/0 Chain sshuttle-12300 (2 references) pkts bytes target prot opt in out source destination 17 1076 REDIRECT tcp -- * * 0.0.0.0/0 10.10.0.0/24 TTL match TTL != 42 redir ports 12300 0 0 RETURN tcp -- * * 0.0.0.0/0 127.0.0.0/8 $ sudo iptables -nL -v -t filter Chain INPUT (policy ACCEPT 97493 packets, 30M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 131K 109M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 1370 89160 ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable [Edit 2: more OpenVPN server output] $ netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 [Edit 3: still more debug output] IP forwarding appears to be enabled correctly on the OpenVPN server: # find /proc/sys/net/ipv4/conf/ -name forwarding -ls -execdir cat {} \; 18926 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/all/forwarding 1 18954 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/default/forwarding 1 18978 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/eth0/forwarding 1 19003 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/lo/forwarding 1 19028 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/tun0/forwarding 1 Client routing table: $ netstat -r Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire 0/1 10.8.0.5 UGSc 8 48 tun0 default 192.168.1.1 UGSc 2 1652 en1 10.8.0.1/32 10.8.0.5 UGSc 1 0 tun0 10.8.0.5 10.8.0.6 UHr 13 0 tun0 10.10.0/24 10.8.0.5 UGSc 0 0 tun0 <snip> Traceroute from client: $ traceroute 10.10.0.9 traceroute to 10.10.0.9 (10.10.0.9), 64 hops max, 52 byte packets 1 10.8.0.1 (10.8.0.1) 5.403 ms 1.173 ms 1.086 ms 2 192.168.1.1 (192.168.1.1) 4.693 ms 2.110 ms 1.990 ms 3 l100.my-verizon-garbage (client-ext-ip) 7.453 ms 7.089 ms 6.248 ms 4 * * * 5 10.10.0.9 (10.10.0.9) 14.915 ms !N * 6.620 ms !N

  Read the article

• Connect to VPN from Mac on Time Capsule network

  - by Lou Franco

  I have a few clients on my network that can connect to my work VPN (Windows PPTP) when they are not on my home network. On my home network (Cable Modem with Time Capsule providing Wifi), it fails very early -- looks like it can't even establish a connection. Logs just say that it failed -- even verbose logs don't have much: I redacted the host and IP from this log, but I can ping it. Wed Feb 2 14:32:41 2011 : PPTP connecting to server 'XXX.XXX.com' (XXX.XX.XX.XX)... Wed Feb 2 14:32:41 2011 : PPTP connection established. Wed Feb 2 14:32:41 2011 : using link 0 Wed Feb 2 14:32:41 2011 : Using interface ppp0 Wed Feb 2 14:32:41 2011 : Connect: ppp0 <--> socket[34:17] Wed Feb 2 14:32:41 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:44 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:47 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:50 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:53 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:56 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:59 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:02 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:05 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:08 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:11 2011 : LCP: timeout sending Config-Requests Wed Feb 2 14:33:11 2011 : Connection terminated. Wed Feb 2 14:33:11 2011 : PPTP disconnecting... Wed Feb 2 14:33:11 2011 : PPTP disconnected Others can get to the VPN and I can too, but not on my network. The only clue I have seen in other forums is to set the NAT default host on the Time Capsule -- I set this to the IP that my mac got over DHCP. I made sure that my Mac gets a different range of IP addresses that it would get if it connected to the VPN (192.168.1.x vs. 10.0.0.x). Not using any VPN client -- just Network System Preferences. It has worked in the past -- but it was a while ago, so I can't pinpoint a change. My sysadmin doesn't even see incoming connections to the VPN (nothing logged about me when I connect). Looking for any diagnostic advice at all

  Read the article

• Too many Bind query (cache) denied, DNS attack?

  - by Jake

  Once Bind crashed and I did: tail -f /var/log/messages I see a massive number of logs every second. Is this a DNS attack? or is there something wrong? Sometimes I see a domain in logs like this: dOmAin.com (upper and lower). As you see there is only one single domain in the logs with different IPs Oct 10 02:21:26 mail named[20831]: client 74.125.189.18#38921: query (cache) 'ns1.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.144.171#38833: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.17#42428: query (cache) 'ns2.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.27#37899: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 193.203.82.66#39263: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.170#59723: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 80.169.197.66#32903: query (cache) 'dOmAin.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 134.58.60.1#47558: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.34#47387: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.8#59392: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.19#64395: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 217.72.163.3#42190: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 83.146.21.252#22020: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.116#57342: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 193.203.82.66#52020: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.72#64317: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 80.169.197.66#31989: query (cache) 'dOmAin.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.18#47436: query (cache) 'ns2.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.16#44005: query (cache) 'ns1.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 85.132.31.10#50379: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 94.241.128.3#60106: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 85.132.31.10#59118: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 212.95.135.78#27811: query (cache) 'domain.com/A/IN' denied /etc/resolv.conf ; generated by /sbin/dhclient-script nameserver 4.2.2.4 nameserver 8.8.4.4 Bind config: // generated by named-bootconf.pl options { directory "/var/named"; /* * If there is a firewall between you and nameservers you want * to talk to, you might need to uncomment the query-source * directive below. Previous versions of BIND always asked * questions using port 53, but BIND 8.1 uses an unprivileged * port by default. */ // query-source address * port 53; allow-transfer { none; }; allow-recursion { localnets; }; //listen-on-v6 { any; }; notify no; }; // // a caching only nameserver config // controls { inet 127.0.0.1 allow { localhost; } keys { rndckey; }; }; zone "." IN { type hint; file "named.ca"; }; zone "localhost" IN { type master; file "localhost.zone"; allow-update { none; }; }; zone "0.0.127.in-addr.arpa" IN { type master; file "named.local"; allow-update { none; }; };

  Read the article

• can't connect 2 subnets through RRAS 2008 r2

  - by mcdwight6

  I'm working on a project for a networking class. In VMWare Workstation, I have to set up a 2008 r2 server with DHCP reservations for 2 clients on separate subnets and have them ping each other. Here is the output of the route print command: =========================================================================== Interface List 13 ...00 50 56 2a e7 11 ...... Intel(R) PRO/1000 MT Network Connection #3 10 ...00 0c 29 66 88 dd ...... Intel(R) PRO/1000 MT Network Connection 1 ........................... Software Loopback Interface 1 24 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 14 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 16 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 17 ...00 00 00 00 00 00 00 e0 isatap.{5B8FB196-616F-4168-A020-03E63A309CEC} =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.0.2 266 0.0.0.0 0.0.0.0 On-link 223.6.6.2 266 10.0.0.0 255.0.0.0 On-link 10.0.0.2 266 10.0.0.2 255.255.255.255 On-link 10.0.0.2 266 10.255.255.255 255.255.255.255 On-link 10.0.0.2 266 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.6.0.0 255.255.0.0 On-link 10.0.0.2 11 128.6.255.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.0 255.255.255.0 On-link 10.0.0.2 11 223.6.6.0 255.255.255.0 On-link 223.6.6.2 266 223.6.6.2 255.255.255.255 On-link 223.6.6.2 266 223.6.6.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.255 255.255.255.255 On-link 223.6.6.2 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.0.2 266 224.0.0.0 240.0.0.0 On-link 223.6.6.2 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.0.2 266 255.255.255.255 255.255.255.255 On-link 223.6.6.2 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.0.0.2 Default 0.0.0.0 0.0.0.0 128.6.0.2 Default 0.0.0.0 0.0.0.0 223.6.6.2 Default 128.6.0.0 255.255.0.0 10.0.0.2 1 223.6.6.0 255.255.255.0 10.0.0.2 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 1010 2002::/16 On-link 14 266 2002:8006:2::8006:2/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None My problem is that although I have set up both dynamic and persistent static routes in my r2 server, neither of the clients can ping even the NIC outside its own subnet. For example Client A can ping the NIC at 10.0.0.2 and vice-versa, but it gets a general transmit failure when it tries to ping the card at 223.6.6.2, let alone trying to ping the other client. I have completely disabled the firewalls on all machines and anything else I could think of, without success. What am I missing? Edit: Since posting this, I also noticed that the default gateways on my 2 NICs keep getting zeroed out. Does anyone know a fix for this?

  Read the article

• MySQL reserves too much RAM

  - by Buddy

  I have a cheap VPS with 128Mb RAM and 256Mb burst. MySQL starts and reserves about 110Mb, but uses not more than 20Mb of them. My VPS Control Panel shows, that I use 127Mb (I also running nginx and sphinx), I know, that it shows reserved RAM, but when I reach over 128Mb, my VPS reboots automatically every 4 hours. So I want to force MySQL to reserve less RAM. How can i do that? I did some tweaks with my.conf but it helped not so much. top output: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2156 668 572 S 0.0 0.3 0:00.03 init 11311 root 15 0 11212 356 228 S 0.0 0.1 0:00.00 vzctl 11312 root 18 0 3712 1484 1248 S 0.0 0.6 0:00.01 bash 11347 root 18 0 2284 916 732 R 0.0 0.3 0:00.00 top 13978 root 17 -4 2248 552 344 S 0.0 0.2 0:00.00 udevd 14262 root 15 0 1812 564 472 S 0.0 0.2 0:00.03 syslogd 14293 sphinx 15 0 11816 1172 672 S 0.0 0.4 0:00.07 searchd 14305 root 25 0 7192 1036 636 S 0.0 0.4 0:00.00 sshd 14321 root 25 0 2832 836 668 S 0.0 0.3 0:00.00 xinetd 15389 root 18 0 3708 1300 1132 S 0.0 0.5 0:00.00 mysqld_safe 15441 mysql 15 0 113m 16m 4440 S 0.0 6.4 0:00.15 mysqld 15489 root 21 0 13056 1456 340 S 0.0 0.6 0:00.00 nginx 15490 nginx 18 0 13328 2388 992 S 0.0 0.9 0:00.06 nginx 15507 nginx 25 0 19520 5888 4244 S 0.0 2.2 0:00.00 php-cgi 15508 nginx 18 0 19636 4876 2748 S 0.0 1.9 0:00.12 php-cgi 15509 nginx 15 0 19668 4872 2716 S 0.0 1.9 0:00.11 php-cgi 15518 root 18 0 4492 1116 568 S 0.0 0.4 0:00.01 crond MySQL tuner: >> MySQLTuner 1.0.1 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering Please enter your MySQL administrative login: root Please enter your MySQL administrative password: -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.0.77 [OK] Operating on 32-bit architecture with less than 2GB RAM -------- Storage Engine Statistics ------------------------------------------- [--] Status: -Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 1M (Tables: 1) [OK] Total fragmented tables: 0 -------- Performance Metrics ------------------------------------------------- [--] Up for: 38m 43s (37 q [0.016 qps], 20 conn, TX: 4M, RX: 3K) [--] Reads / Writes: 100% / 0% [--] Total buffers: 28.1M global + 832.0K per thread (100 max threads) [OK] Maximum possible memory usage: 109.4M (42% of installed RAM) [OK] Slow queries: 0% (0/37) [OK] Highest usage of available connections: 1% (1/100) [OK] Key buffer size / total MyISAM indexes: 128.0K/64.0K [OK] Query cache efficiency: 42.1% (8 cached / 19 selects) [OK] Query cache prunes per day: 0 [!!] Temporary tables created on disk: 27% (3 on disk / 11 total) [!!] Thread cache is disabled [OK] Table cache hit rate: 57% (8 open / 14 opened) [OK] Open file limit used: 1% (12/1K) [OK] Table locks acquired immediately: 100% (22 immediate / 22 locks) [!!] Connections aborted: 10% [OK] InnoDB data size / buffer pool: 1.5M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries When making adjustments, make tmp_table_size/max_heap_table_size equal Reduce your SELECT DISTINCT queries without LIMIT clauses Set thread_cache_size to 4 as a starting value Your applications are not closing MySQL connections properly Variables to adjust: tmp_table_size (> 32M) max_heap_table_size (> 16M) thread_cache_size (start at 4) I think if I do what MySQLtuner says, MySQL will use more RAM.

  Read the article

• IPv6 host route is deleted after PMTU expires

  - by SAPikachu

  I am experimenting my new IPv6 tunnel setup between my local Ubuntu box and a scratch Linode. I set up some docker containers, configured 6in4 tunnel server and IPv6 forwarding on the Linode: # uname -a Linux argo 3.15.4-x86_64-linode45 #1 SMP Mon Jul 7 08:42:36 EDT 2014 x86_64 x86_64 x86_64 GNU/Linux # ip addr .. snipped .. 48: sit-sapikachu: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1472 qdisc noqueue state UNKNOWN group default link/sit 106.185.41.115 peer 1.2.3.4 inet6 fd00::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::6ab9:2973/64 scope link valid_lft forever preferred_lft forever 13: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default link/ether 56:84:7a:fe:97:99 brd ff:ff:ff:ff:ff:ff inet 172.17.42.1/16 scope global docker0 valid_lft forever preferred_lft forever inet6 fc00::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::5484:7aff:fefe:9799/64 scope link valid_lft forever preferred_lft forever // Docker containers are bridged to docker0 On my local box, I configured a 6in4 tunnel interface to connect to the Linode box, and added a host route to one of the docker container: # uname -a Linux sapikachu-netbox 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux # ip addr .. snipped .. 16: sit-argo: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN group default link/sit 0.0.0.0 peer 106.185.41.115 inet6 fd00::2/64 scope global valid_lft forever preferred_lft forever inet6 fe80::a97:302/64 scope link valid_lft forever preferred_lft forever inet6 fe80::ac19:1/64 scope link valid_lft forever preferred_lft forever inet6 fe80::c0a8:1f0/64 scope link valid_lft forever preferred_lft forever inet6 fe80::c0a8:1fa/64 scope link valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether *** brd ff:ff:ff:ff:ff:ff .. snipped .. inet6 fd00:0:1::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::2e0:6fff:fe0e:365e/64 scope link valid_lft forever preferred_lft forever # ip route replace fc00::1875:8606:d8c1:8a9d via fd00::1 # Add route to docker container # ip -6 route .. snipped unrelated routes fc00::1875:8606:d8c1:8a9d via fd00::1 dev sit-argo metric 1024 expires 590sec mtu 1472 fd00::/64 dev sit-argo proto kernel metric 256 fd00:0:1::/64 dev eth0 proto kernel metric 256 fe80::/64 dev sit-argo proto kernel metric 256 (Note that tunnel MTU on my local box is different from the server, this is intentional for testing) After adding the host route to the docker container (fc00::1875:8606:d8c1:8a9d), I can ping the container without problem until the route expires. After that I couldn't get reply any more. If I run ip -6 route in a few seconds after expiration, expiration time of the host route will be a negative number: fc00::1875:8606:d8c1:8a9d via fd00::1 dev sit-argo metric 1024 expires -1sec And output of ip route get fc00::1875:8606:d8c1:8a9d shows that it is routed to my default IPv6 gateway (which fails to route it correctly of course, since the address is not globally routable). After some time, the host route disappears without a trace. This problem won't happen if I do either one of the following things: Set MTU of tunnel on my local box to be the same as the server (1472). The route won't have expiration time in both ip -6 route and ip route get in this case. Instead of adding a host route, add a route with network mask (even /127 works). In this case ip -6 route shows the route without expiration time, ip route get shows expiration time but it will be correctly refreshed after expiration. Although this problem can be easily resolved, I am curious to know why this happens. Is there error in my configuration, or is this a kernel bug?

  Read the article

• "ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver" wheel-click is wrong

  - by sputnick

  I use this mouse under archlinux x86_64 with 3.2.8-1-ARCH kernel. I have some problems to select and then paste with the wheel-click in some applications like konversation, not in a terminal nor an editor. I don't know if it's a hardware problem or a software one. $ lsusb -v Bus 002 Device 110: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x046d Logitech, Inc. idProduct 0xc50e Cordless Mouse Receiver bcdDevice 25.10 iManufacturer 1 Logitech iProduct 2 USB RECEIVER iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 34 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 70mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.11 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 95 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) When I see what's happens in xev, the output is different compared to another mouse My buggy Logitech mouse : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350700, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350700, (48,52), root:(1491,75), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 16 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350988, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350988, (48,52), root:(1491,75), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 a working mouse (dell) : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245131, (46,32), root:(1489,55), state 0x10, button 2, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245131, (46,32), root:(1489,55), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 528 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245411, (46,32), root:(1489,55), state 0x210, button 2, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245411, (46,32), root:(1489,55), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 A demo of the problem when I use konversation (IRC) : http://www.youtube.com/watch?v=lhmr92M7NCc I tried to modify the button map with xmodmap like this with no success (one at a time) : xmodmap -e "pointer = 1 0 3" xmodmap -e "pointer = 1 1 3" xmodmap -e "pointer = 1 2 3" xmodmap -e "pointer = 1 3 3" xmodmap -e "pointer = 1 4 3" xmodmap -e "pointer = 1 5 3" xmodmap -e "pointer = 1 6 3" xmodmap -e "pointer = 1 7 3" xmodmap -e "pointer = 1 8 3" xmodmap -e "pointer = 1 9 3" xmodmap -e "pointer = 1 10 3" xmodmap -e "pointer = 1 11 3" xmodmap -e "pointer = 1 12 3" xmodmap -e "pointer = 1 13 3" xmodmap -e "pointer = 1 14 3" xmodmap -e "pointer = 1 15 3" xmodmap -e "pointer = 1 16 3" xmodmap -e "pointer = 1 17 3" xmodmap -e "pointer = 1 18 3" xmodmap -e "pointer = 1 19 3" xmodmap -e "pointer = 1 20 3" xmodmap -e "pointer = 1 21 3" xmodmap -e "pointer = 1 22 3" xmodmap -e "pointer = 1 23 3" xmodmap -e "pointer = 1 24 3" xmodmap -e "pointer = 1 25 3" Any clue ? I would like to avoid buying a new mouse just for a paste problem.

  Read the article

• RedHat 5.5 server does not show per processor memory utilization

  - by Mike S

  I have been searching all over internet but not finding any leads. I have a system with a memory leak that I am trying to troubleshoot. Unfortunately I am not able to see per processor memory utilization. Here are the outputs of TOP and PS commands. Linux SERVER_NAME 2.6.18-194.8.1.el5 #1 SMP Wed Jun 23 10:52:51 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux top - 09:17:13 up 18:43, 3 users, load average: 0.00, 0.00, 0.00 Tasks: 375 total, 1 running, 373 sleeping, 0 stopped, 1 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32922828k total, 32776712k used, 146116k free, 267128k buffers Swap: 5245212k total, 0k used, 5245212k free, 32141044k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 10348 744 620 S 0.0 0.0 0:05.65 init 2 root RT -5 0 0 0 S 0.0 0.0 0:00.05 migration/0 3 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/0 4 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 5 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/1 6 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/1 7 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 8 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/2 9 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/2 10 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/2 11 root RT -5 0 0 0 S 0.0 0.0 0:00.01 migration/3 12 root 34 19 0 0 0 S 0.0 0.0 0:00.01 ksoftirqd/3 13 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/3 14 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/4 15 root 34 19 0 0 0 S 0.0 0.0 0:00.01 ksoftirqd/4 16 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/4 17 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/5 18 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/5 19 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/5 20 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/6 % ps -auxf | sort -nr -k 4 | head -10 Warning: bad syntax, perhaps a bogus '-'? See /usr/share/doc/procps-3.2.7/FAQ xfs 6205 0.0 0.0 23316 3892 ? Ss Aug19 0:00 xfs -droppriv -daemon uuidd 6101 0.0 0.0 60976 224 ? Ss Aug19 0:00 /usr/sbin/uuidd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND smmsp 6130 0.0 0.0 57900 1784 ? Ss Aug19 0:00 sendmail: Queue runner@01:00:00 for /var/spool/clientmqueue rpc 5126 0.0 0.0 8052 632 ? Ss Aug19 0:00 portmap root 99 0.0 0.0 0 0 ? S< Aug19 0:00 [events/1] root 98 0.0 0.0 0 0 ? S< Aug19 0:00 [events/0] root 97 0.0 0.0 0 0 ? S< Aug19 0:00 [watchdog/31] root 96 0.0 0.0 0 0 ? SN Aug19 0:00 [ksoftirqd/31] root 95 0.0 0.0 0 0 ? S< Aug19 0:00 [migration/31] Any help with this is appretiate.

  Read the article

< Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >