Search Results

Search found 5670 results on 227 pages for 'zend router'.

Page 177/227 | < Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >

• Two identical fiber optic broadband lines working as one

  - by Katafalkas

  I have been trying to find an answer to this, but all I can find is hobbyists trying to connect their Linksys devices to get some magic out of them. I am looking for a way I could combine two 100Mbit fiber optic lines into a single connection for our office. I assume it involves some Cisco learning or something similar. Do I need to configure some big router to load-balance the NATing in some way? I assume that many of you have done something similar and hope someone could share their knowledge or at least provide me some tips on how to do this.

  Read the article

• MikroTik ipv6 Tunnel

  - by MikeSmitty

  I've got a MikroTik router set up with the latest stable OS on it, and I just set up an ipv6 tunnel with Hurricane Electric, but I'm having an odd issue with it. I can't ping anything until I first ping the tunnel endpoint on HE's side. After that I can ping any ipv6 address fine, but give it a little time (say, maybe 30 sec) and I can't ping any ipv6 addresses again. Whenever it stops allowing ping to go through I notice the counter on my firewall rule that drops invalid connections goes up. this is my ipv6 firewall config: add action=accept chain=input comment="" connection-state=established \ disabled=no in-interface=sit1 add action=accept chain=input comment="" connection-state=related disabled=no \ in-interface=sit1 add action=accept chain=input comment="" disabled=no in-interface=bridge \ src-address=ipv6_address_here/64 add action=drop chain=input comment="" connection-state=invalid disabled=no \ in-interface=sit1 add action=drop chain=input comment="" disabled=no in-interface=sit1 Any ideas on what it could be?

  Read the article

• How can I route packets from one application to a virtual machine in windows 7?

  - by user836045

  I am trying to test an application running in windows 7, and I would like to send the packets it generates to a server VM (I am using virtualbox) on the local machine which will act as a simulation for when packets will be really sent over the internet to a distant server. I need to check for correctness of the packets in certain situations. Is there a way on windows to take packets produced by an application and instead of passing it to my router, pass it along to another process, i.e. my virtual machine. I'd prefer not to change any of the code on my application and would rather find an outside solution. Is there such a solution for windows 7?

  Read the article

• ICS as guest in Ubuntu 12.04 host

  - by oshirowanen

  I have installed Android as per this guide as a guess os via VirtualBox: http://www.android-x86.org/documents/virtualboxhowto Using the following ISO: android-x86-4.0-RC1-eeepc.iso But I am unable to connect to the internet from within the android virtual machine. The host OS is Ubuntu 12.04 where the internet works fine. I have internet access via a usb wireless connection to the home router. All this is fine. If I install Ubuntu 12.04 as a guest, where the host is also Ubuntu 12.04. The guest os'es internet works fine out of the box. But for some reason, I can't get the above androids internet to work out of the box as the guest os. Anyone know what I am doing wrong?

  Read the article

• Ubuntu to Ubuntu VNC over SSH tunnel

  - by rxt

  I have a Linux Ubuntu desktop at home, ssh enabled, vnc server installed, router rule configured. It all works, and at home I can connect via the local network from my Mac. From the outside I can login via ssh. I've configured putty as follows: session: host name and port number connection ssh tunnel: forwarded ports: L5900|192.168.0.23 the local address is: 192.168.1.45 When I make the connection I can login to the remote machine. Then I open Remote Desktop Viewer. I click connect protocol: vnc host: ? use host as ssh tunnel: ? I don't know what to use for the last two options. Which ip-addresses should I use?

  Read the article

• Why would image thumbnails not be showing in all search engines in all browsers?

  - by Edward Tanguay

  For over a week now, when I search for a word at Google, it correctly gives me some preview image thumbnails: But when I click on "images", it doesn't show me any thumbnails: The same thing happens at Bing.com, when I search Bing itself it gives me some thumbnails on the general search result page: But when I click on "images", it doesn't show me any thumbnails: The same thing happens at Yahoo: If I click on one of the broken thumbnails, it shows me the picture fine: Thumbnails at youtube also work fine: It seems each search engine is hanging on different URLs as shown above: t1.gstatic.com ts3.mm.bing.net thm-a02.yimg.com so it doesn't seem to be the problem of one specific URL not sending thumbnails, it is just a problem with search engine image thumbnails in general. Also, this happens in every browser I try: Explorer, Firefox, Chrome. What could be the problem? Is it my computer, some setting somewhere, my router, my Internet provider (T-Online, Germany)? Has anyone ever had this problem and solved it?

  Read the article

• DYNDNS setup with TightVNC on Windows Server 2008 R2

  - by StealthRT

  Hey all, i seem to be having a problem with getting ports to forward on my Windows Server 2008 R2 PC. I already set all my port forwarding for 5900/5800 on my router for my PC's IP address (192.168.1.22) but when i try to use the TightVNC PFPortChecker on port 5900 it tells me its not opened! I can not even connect to my DYNDNS server name (xxxxxxx.dyndns.org). As a side note, i am running Windows XP SP3 within a VirtaulBox inside Windows Server 2008 R2 but running the PFPortChecker in Windows 2008 R2 brings the same results as it does in the VM. I also added them to the Windows Firewall Advanced Security form to add those inbound ports for full access. What could i possibly be missing? Thanks for your time! David

  Read the article

• DNS resolution over DHCP

  - by Eric

  I have a m0n0wall router a VMWare workstation running ubuntu a windows 7 workstation running the VM The ubuntu hostname is "renraku" From the windows machine I can't resolve dns automatically for this host. For example, when I ping renraku Ping request could not find host renraku. Please check the name and try again. However nslookup seems to work nslookup renraku Server: m0n0wall.local Address: 192.168.123.254 Name: renraku Address: 192.168.123.248 I don't get how to have ping to work with hostnames. The main goal behind this is to have my web server to work with hostnames instead of ip addresses EDIT : ping 192.168.123.248 works

  Read the article

• Manage MS SQL server over SSH (putty)

  - by adopilot

  There is great implementation of PuttY for Symbian S60 devices, and last versions of Nokia phones with full QWERTY keyboard offers comfort for using Putty and SSH goodies. I start wondering is there a way to access MSSQL over SSH and send T-SQL commands. I am able to connect my router which running on FreeBSD OS, also other CentOS server with MYSQL are able to me over SSH. I want to try access MS-SQL-2005 from my mobile phone, Probably this is not going to have daily use, it is just for geeky and justification to myself: why I had to buy so expensive a toy

  Read the article

• Share the DVB card on windows 7

  - by Bashar Kernel

  I have 2 computers connected to a router and I have a DVB card in one of them. I want to use the one DVB card to feed both of them. I read about it and I know that I want to share the DVB adapter with the Internet Connection Sharing on the LAN network. But when I use the connection sharing, I lose my internet access I tried to use "Bridge Connection", but then I also lost my internet access too. Can any one tell me how to fix this problem? And how to view the channels (for example how to use the VLC)?

  Read the article

• Process for configuring network settings on a headless rack mount device

  - by PherricOxide

  I'm with a small company that plans to sell a rack mounted network appliance which is configurable via a web interface (think of a router configuration page sort of deal), and I'm wondering in large data center like environments what the process usually is for the initial setup of such systems. The main question is, if the system is headless, how do you get initial remote access to it? Do companies usually first plug a server into a monitor/keyboard/mouse in order to configure the network settings before mounting it in a rack? How else would they know what the IP address of the machine was if DHCP (and it can't be hard coded because of IP conflict potential)?

  Read the article

• Setting a Static IP Running FreeBSD8 in VirtualBox hosted on Windows 7

  - by gvkv

  I'm using VirtualBox on Windows 7 (host) to run a FreeBSD (guest) based web server. I`ve assigned a static ip of 192.168.80. 1 to the (virtualized) NIC which is run in bridged mode. The problem is that when I ping an external server (such as google.com) I get a No route to host error: dimetro# ping google.com PING google.com (66.249.90.104): 56 data bytes ping: sendto: No route to host ... I can ping the BSD server from both another virtualized machine and my host machine and from the server, I can ping everything on the network. The router ip is 192.168.1.1/16. ADDENDUM: I have the following lines in /etc/rc.conf on the BSD VM to configure networking: defaultrouter="192.168.1.1" ifconfig_em0="inet 192.168.80.1 netmask 255.255.0.0"

  Read the article

• How do I configure OpenVPN for accessing the internet with one NIC?

  - by Lekensteyn

  I've been trying to get OpenVPN to work for three days. After reading many questions, the HOWTO, the FAQ and even parts of a guide to Linux networking, I cannot get my an Internet connection to the Internet. I'm trying to set up a OpenVPN server on a VPS, which will be used for: secure access to the Internet bypassing port restrictions (directadmin/2222 for example) an IPv6 connection (my client does only have IPv4 connectivity, while the VPS has both IPv4 and native IPv6 connectivity) (if possible) I can connect to my server and access the machine (HTTP), but Internet connectivity fails completely. I'm using ping 8.8.8.8 for testing whether my connection works or not. Using tcpdump and iptables -t nat -A POSTROUTING -j LOG, I can confirm that the packets reach my server. If I ping to 8.8.8.8 on the VPS, I get an echo-reply from 8.8.8.8 as expected. When pinging from the client, I do not get an echo-reply. The VPS has only one NIC: etho. It runs on Xen. Summary: I want to have a secure connection between my laptop and the Internet using OpenVPN. If that works, I want to have IPv6 connectivity as well. Network setup and software: Home laptop (eth0: 192.168.2.10) (tap0: 10.8.0.2) | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | router/gateway (gateway 192.168.2.1) | INTERNET | VPS (eth0:1.2.3.4) (gateway, tap0: 10.8.0.1) (running Debian 6; OpenVPN 2.1.3-2) wifi and my home router should not cause problems since all traffic goes encrypted over UDP port 1194. I've turned IP forwarding on: # echo 1 > /proc/sys/net/ipv4/ip_forward iptables has been configured to allow forwarding traffic as well: iptables -F FORWARD iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -A FORWARD -j DROP I've tried each of these rules separately without luck (flushing the chains before executing): iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j SNAT --to 1.2.3.4 iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE route -n before (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n after (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n before (client): 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 route -n after (client): 1.2.3.4 192.168.2.1 255.255.255.255 UGH 0 0 0 wlan0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 128.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 SERVER config proto udp dev tap ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" ifconfig-pool-persist ipp.txt keepalive 10 120 tls-auth ta.key 0 comp-lzo user nobody group nobody persist-key persist-tun log-append openvpn-log verb 3 mute 10 CLIENT config dev tap proto udp remote 1.2.3.4 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 mute 20 traceroute 8.8.8.8 works as expected (similar output without OpenVPN activated): 1 10.8.0.1 (10.8.0.1) 24.276 ms 26.891 ms 29.454 ms 2 gw03.sbp.directvps.nl (178.21.112.1) 31.161 ms 31.890 ms 34.458 ms 3 ge0-v0652.cr0.nik-ams.nl.as8312.net (195.210.57.105) 35.353 ms 36.874 ms 38.403 ms 4 ge0-v3900.cr0.nik-ams.nl.as8312.net (195.210.57.53) 41.311 ms 41.561 ms 43.006 ms 5 * * * 6 209.85.248.88 (209.85.248.88) 147.061 ms 36.931 ms 28.063 ms 7 216.239.49.36 (216.239.49.36) 31.109 ms 33.292 ms 216.239.49.28 (216.239.49.28) 64.723 ms 8 209.85.255.130 (209.85.255.130) 49.350 ms 209.85.255.126 (209.85.255.126) 49.619 ms 209.85.255.122 (209.85.255.122) 52.416 ms 9 google-public-dns-a.google.com (8.8.8.8) 41.266 ms 44.054 ms 44.730 ms If you have any suggestions, please comment or answer. Thanks in advance.

  Read the article

• WEP key not working on laptop running Ubuntu

  - by stupid-idiot

  I can't connect to my router via wifi from my laptop (running Ubuntu) even if I'm 100% sure the WEP key I punch in is correct. It works via LAN though. I'm also not able to ping localhost 127.0.0.1. I had some problems setting up the radio on my network card but I think that that works since it finds some wireless networks. (Although it's much much faster than Windows it's useless since I can't download any libraries for development.) What could be wrong with my setup?

  Read the article

• How should I remotely manage Dell Poweredge 2850 running Ubuntu server?

  - by Saul

  First I've got to say I'm a Linux / Ubuntu novice, so go gentle on me as I'm on day 3. I've managed to get Ubuntu server Ubuntu 8.04 LTS installed and running on the Poweredge 1850 I bought off ebay. The box will go in a rack at my office but I want to be able to work on it and power on and off from home and I gather that (maybe) IPMI over LAN might be the way to do this, or maybe its something to do with BMC or something? I want to be able to administer/manage from a client PC at home running XP. I will be configuring the office router to port forward port 80 and 443 to the Ubuntu server running Apache2, and I'm puzzled about how the remote management works (unless it comes on a different port forwarded to a different internal IP) Thanks for any help

  Read the article

• DDWRT or similar as repeater in a network.

  - by Quantumplation

  I have a friend with sever connection issues due to her wireless router being on the bottom floor of her house, and the computer being a story or two away. I have several old Linksys routers lying about, one of which is currently running DDWRT for my network. Would it be a good idea (effective) to configure one of these routers as a wireless bridge of some kind in an intermediary floor to improve her connection? Is there any specific configuration beyond the standard DDWRT setup that I would need to do? Thanks for your help. =)

  Read the article

• Internet Connection Sharing on OSX causes delayed web requests

  - by Vanthel

  I have an iMac connected to my router via WiFi, and a PC connected by ethernet to the iMac. The iMac is sharing its connection. I've never had a problem with this in the past (pre Lion anyway) but now all web page requests take an eon to resolve on the iMac (they are instant on the PC). It suggests to me the iMac is attempting to resolve it through the PC first every time? I've tried reordering the connections in the network settings but that made no difference.

  Read the article

• How is my ISP DNS hijacking AFTER all these precautions?

  - by user973917

  In IE9 when I search for anything my ISP hijacks google search and I get this result. To add complication to this I've already changed the default DNS servers (OpenDNS) months ago. This only happens in IE9; even after machine reboots and cache flushing. I even have my router (dd-wrt) intercepting all requests for DNS and I am still getting this result. I have all extensions disabled and there are no toolbars. This is IE9 from M$. This is not malware; it happens all machines with IE installed (even IE7/8).

  Read the article

• Cannot see http (apache) server outside home network

  - by user165155

  Ive been racking my brain with this all evening. Power went out with a tstorm today, started back up my server... running apache and a team speak server on it. TS is great, cant see my web page outside my network! Firewall is disabled on the pc running it (centos btw), apache is running and working. correct ports are forwarded on my router (my isp blocks port 80). Ive tried changing ports, pretty much everything i can think of. httpd.conf is pointing to the correct addy and port, and my domain is pointing to the correct external ip. Im at a loss, any ideas out there?

  Read the article

• How can I monitor network traffic in an all Mac home network?

  - by raiglstorfer

  I have an all Mac network consisting of an Airport Extreme, 1 MacPro, 1 Mac Mini, 2 MackBook Pros, 2 iPads, and 2 iPhones. The Mac Pro is connected directly to the Airport Extreme via Cat5 and the rest is all running via Wireless. Lately I've been getting prompted by Google to enter Capchas frequently. The message states that I might have software running on my network I'm not aware of. My wireless router is password protected using WPA2 Personal and I frequently change my password so I don't think someone is using the network from outside (but I've no way to confirm this). I'm looking for a relatively cheap (preferably open source) solution that would enable me to monitor and profile the network usage by machine and port. Can someone recommend a solution?

  Read the article

• Find DNS server automatically

  - by jdickson

  I've got a Windows 2012 server set up as a domain controller and DNS server in my basement. On my laptop, if I set it to use the IP address of my server as the DNS server, then it works as expected. The problem with that is that I use my laptop outside my home network and I need to switch it back to automatic. Setup is like this: ISP Router running DD-WRT Win 2012 DC/DNS and other network computers How can I have my laptop find the DNS server automatically instead of using my ISP's DNS servers?

  Read the article

• OpenVPN server behind firewall issues

  - by Gabriel

  I'm trying to setup an OpenVPN but I do have some problems doing it. This is my scenario: INTERNET --- HOME ROUTER (10.1.0.0/28) --- FIREWALL SERVER (DEFAULT GATEWAY FOR MY INTERNAL LAN 10.1.0.2) --- OpenVPN Server (10.1.0.9 LAN | 10.2.0.1 VPN) single nic / bridge iface I can connect to my VPN server successfully (it gets the 10.2.0.5 address). Though, I'm not able to ping anything, neither my VPN server, nor my lan clients. I guess the problem is on the firewall. I'm not really an expert on iptables, I tried adding plenty of different rules without success. I would appreciate a lot if someone could explain me how to get to work the VPN server in this scenario. After connecting through VPN, when I try to ping the server, I'm not really sure about how the ping message gets to the server and how the response should go back to the client. Thanks a lot Gabriel

  Read the article

• Linux (Kubuntu 9.10): Strange DNS problem [seems to be IPv6 issue]

  - by Homer J. Simpson

  Hi, I'm experiencing strange problems with my Kubuntu 9.10 when doing DNS requests from various applications. The requests are extremely slow, so loading any pages in Firefox or Konqueror, doing package installations in Kpackagemanager and other apps is really painful, while for example Opera doesnt have any problems, and ping is normally fast as well for DNS pings. I checked the proxy settings of both the used applications as well as of the general system and there are none, so to me it doesn't seem as there was something inbetween.. Does anybody have an idea on what to check for possible problem sources or how to solve this ? I'm behind a DSL home router which does the DHCP (and works well with my other computer). Any kind of advice would be really helpful. Edit: It seems to be some kind of IPv6 problem, as I could get it to work by disabling IPv6 explicitly in Firefox. Is there a general solution to this ?

  Read the article

• Cannot ping ubuntu server by hostname - can only ping by IP

  - by Tone

  I have an unbuntu 9.10 server and have set the hostname to "fileserver" When I try to ping fileserver from a client machine it doesn't find it, however I can ping by the IP my router assigns it. I have tried changing the ip in /etc/hosts from this: 127.0.0.1 fileserver to this: 192.168.1.109 fileserver which is the ip being assigned. I had a previous install of this server and i had no issues with this - only difference in this install is i did not select any of the options such as LAMP, OpenSSH, etc during the install process. I can access the machine fine by ip using PuTTY. Any ideas?

  Read the article

• Can a virtual mikrotik box bridge a hyper-v internal network with a hyper-v external network?

  - by mcfrosty

  I am trying to set up a Mikrotik router as a transparent firewall on my network. I got the machine working on a hardware MT box, but my boss wants the MT virtualized. I have been trying the set up where my virtual windows box talks to the Mikrotik via private or internal network on the Hyper-V host. I can get the two machines to talk, but as soon as I set up a bridge on the MT, all traffic ceases between the two. Is it possible to create a bridge for this purpose (having the MT silently in front of my firewalled server)? I could really use some help.

  Read the article

< Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >