Search Results

Search found 8790 results on 352 pages for 'known hosts'.

Page 178/352 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• nginx www.domain.com vs domain.com virtualhost

  - by m33lky

  I have an http block where I include virtual hosts for the different domains hosted on the same server. For each virtual host I do: listen domain.com:80; Now, domain2.com works fine. However, when I do www.domain2.com it shows the page for domain1.com! How to properly configure nginx? Does this have something to do whether www is a CNAME or an A record? Update: It looks like you can do the following: listen 80; server_name domain.com www.domain.com;

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• DKIM for email through Google Apps domain with external outbound relay

  - by David Gardiner

  I'd like to enable the new Domain Keys DKIM email authentication feature for a domain hosted in Google Apps. Some of my users use an external SMTP gateway (such that when they send email, it doesn't go through smtp.gmail.com). I have an SPF record configured for the domain, and this allows the external SMTP gateways as valid SMTP hosts. (I realise SPF is different to DKIM) Will enabling DKIM adversely affect the external gateway email? eg. Are the externally sent emails at risk of being marked as spam because they would not have the DKIM signature, or will DKIM only positively benefit emails sent through Google's SMTP server?

  Read the article

• Blocking a country (mass iP Ranges), best practice for the actual block

  - by kwiksand

  Hi all, This question has obviously been asked many times in many different forms, but I can't find an actual answer to the specific plan I've got. We run a popular European Commercial deals site, and are getting a large amount of incoming registrations/traffic from countries who cannot even take part in the deals we offer (and many of the retailers aren't even known outside Western Europe). I've identified the problem area to block a lot of this traffic, but (as expected) there are thousands of ip ranges required. My question now (finally!). On a test server, I created a script to block each range within iptables, but the amount of time it took to add the rules was large, and then iptables was unresponsive after this (especially when attempting a iptables -L). What is the most efficient way of blocking large numbers of ip ranges: iptables? Or a plugin where I can preload them efficiantly? hosts.deny? .htaccess (nasty as I'd be running it in apache on every load balanced web server)? Cheers

  Read the article

• Single Exchange 2007 server - two AD domains

  - by TheCleaner

  CURRENT: single domain, single Exchange 2007 NEW: two domains, single Exchange 2007 Can this be done? Details: Current setup is a single W2k3 domain with a single Exchange 2007 server. We are merging with another company that currently hosts their email with their ISP via POP3. We'd like to start hosting their email on our Exchange server using their existing domain SMTP addresses. They don't have an AD domain at all at the moment. Recommendations? Can I do this with a trust between the 2 domains? Requirements: They can't have multiple SMTP addresses on both domains...such as I've seen with articles pointing to "hosting multiple domains". I want companyA to have the same account settings they've always had...companyB to have the same SMTP address they've had and not an additional one on the current companyA Exchange domain. They should be able to collaborate (calendar, contacts, GALs) but should still be distinguishable based on which company they "work for". Please help...thanks!

  Read the article

• Why is it a bad idea to use multiple NAT layers or is it?

  - by iamrohitbanga

  The computer network of an organization has a NAT with 192.168/16 IP address range. There is a department with a server that has an IP address 192.168.x.y and this server handles hosts of this department with another NAT with the IP address range 172.16/16. Thus there are 2 layers of NAT. Why don't they have subnetting instead. This would allow easy routing. I feel multiple layers of NAT can cause performance losses. Could you please help me compare the two design strategies.

  Read the article

• How to setup external mail addresses without external autodiscover tries?

  - by Tarnschaf

  We have a little Exchange/Outlook installation here that fetches the mails from our provider with POP3. Now to be able to send emails outside our organisation, I added another SMTP address to the Exchange User: [email protected] (Default / Reply Address) [email protected] Sending email works using the default address. But now there is an error message each time we start Outlook. Outlook tries to autodiscover using autodiscover.ourcompany.com which doesn't exist. Our autodiscover files are placed on our local server. I think all the servers are discovers, because everything works as expected. Everything except the error message on each Outlook start. (The error message is actually because of an invalid certificate but I don't see why Outlook should contact an external host at all!) So how can I solve this? Forcing Autodiscover on every Outlook client to use the local hosts? Or ist there an even better way?

  Read the article

• GF 3.0.1 + Virtual Server: www.myhost.com:8080/projectname-war => www.myhost.com. How?

  - by Harry Pham

  I need to change www.myhost.com:8080/myproject-war to www.myhost.com. This is what I try. In admin console in Glassfish 3.0.1, I create a http-listener-3 with port 9090 and address 0.0.0.0 (I want to have port 80, but got access-denied or some sort). I then create a virtual server call scholar, with Id=scholar, Hosts=${com.sun.aas.hostName}, Network Listeners: http-listener-3, Default Web Module=project#project-war.war(it is the only option from the drop down list since I only deploy 1 app). Then under Applications, I set the virtual server of the application to be scholar. Save and restart. I try localhost:9090, and expecting that it will load my project like as if I type localhost:9090/project-war. But it does not. I already set the Default Web Module, to be the project, why doesnt it load the project by default?

  Read the article

• How can I make gitosis distinguish between two users with the same username

  - by bryan kennedy

  I have a gitosis system that seems to be working correctly except for a common problem we run into where I can't distingush permissions between two users who have the same username, but different hosts. For example: [email protected] 's SSH key is in the key folder. And so is [email protected] 's SSH is also in the key folder. These two jsmith's are two different people on two different computers. However, when I configure them in the gitosis.conf file with the usernames jsmith@computer or jsmith@machine, it seems like each user just gets the same permission. Can gitosis not distinguish the full username (name and host)? If not, how do I deal with multiple users accessing our system with common usernames? Thanks for any help.

  Read the article

• Tomcat 5.5 - multiple contexts using same path

  - by ctn8iv

  Is it possible to set up multiple contexts using the same path? For example: <Context docBase="/www/websites/site1/java/base" path="/base" reloadable="true"/> <Context docBase="/www/websites/site2/java/base" path="/base" reloadable="true"/> I have two sites that use the same path both running on the same server/IP. The sites use different virtual hosts and different ServerNames, but I have no control over the directory structure of the sites because they are maintained by a client. Until now, they have been content with only allowing one site to run at a time, but this is a major hassle, so I need to know if there's a workaround.

  Read the article

• tomcat dns forwarding to multiple applications

  - by basis vasis

  I recently installed business objects software on tomcat 6. I have 2 domains - domain1 and domain2. This software allows access to two of its applications via these URLS: ADDRESS:http://myservername.domain1:8080/BO/APP1 and ADDRESS:http://myservername.domain1:8080/BO/APP2. Instead of these urls, I would like the end users to access these apps via something like http://bobj.domain2.com:8080/BO/APP1 and http://bobj.domain2.com:8080/BO/APP2. I cannot figure out how to accomplish that. I have looked into the option of http redirect (not good because the destination address shows up in the address bar), domain forwarding (not sure if it would work with multiple applications and forwarding from one domain to another) and also using apache tomcat with mod_jk by using virtual hosts (not sure if it is possible when forwarding from one domain to a sub domain in another domain) ?? please advise as to what would be my best option and how to accomplish. thanks a bunch

  Read the article

• IP assignment in a /28 block

  - by mks

  Need help on setting up firewall router. My config is as below: Public static network ID: x.x.x.48/28 gateway: x.x.x.49 available IP for the hosts: x.x.x.52 to 62 gw_eth0 <-- fw_eth0 - fw_eth1 <-- dmz_switch Four servers are connected on dmz_switch (say s1, s2, s3, s4) all have to use public static IP address from the above block. Any recommendation on IP assignment and route setup? Do I need to subnet the above block further or simply use /32 netmask and point-to-point static routes in the above setup?

  Read the article

• Why is my vhosts file interfering with my apache deployment?

  - by Avery Chan

  When I enable my vhosts file (i.e. uncomment this line: Include /private/etc/apache2/extra/httpd-vhosts.conf) I am unable to reach localhost. I /am/ able to reach the last virtual host listed in my vhosts file: <VirtualHost *:80> DocumentRoot "/Users/achan/Sites/epwbst" ServerName epwbst </VirtualHost> <VirtualHost *:80> DocumentRoot "/Users/achan/Sites/pxproj" ServerName pxproj </VirtualHost> Typing pxproj in my browser brings up the expected web content. But I am unable to reach epwbst or localhost. If I re-comment the vhost line in my httpd.conf, I am able to reach local host (i.e. "It works!") but obviously am unable to reach my virtual hosts. I don't know how to continue troubleshooting this. Why can't I reach localhost when I've got my vhosts turned on? OS: Mac OS X 10.7 Server version: Apache/2.2.21 (Unix)

  Read the article

• Snow Leopard connecting to Unbuntu 10.04 through Samba failure -- need help fixing.

  - by Chris Altman

  I have a Ubuntu 10.04 web server. I want to connect to it with my OSX 10.6 machine and Finder. I have installed openSSH and Samba on the Ubuntu machine. In my smb.conf I have a Share Definition: [www] comment = Development Computer WWW path = /var/www writeable = yes browseable = yes allow hosts = 192.168.1. I can connect to the machine through Finder using a non-root user. When I attempt to add files thought Finder I get an "Insufficient Permissions" error. Please help. I am not sure if the issue is in the Samba configuration or OSX 10.6 Thank you

  Read the article

• Isn't NAT a MUST when a LAN uses rfc 1918 private IPs?

  - by aks

  Isn't NAT a MUST when a LAN uses rfc 1918 private IPs? Can an organization assign its hosts with private IPs and still communicate with the external world without NAT? how can an internal host with a private IP (say 10.1.1.1) communicate with external world without NAT? I mean, how can the reply/response packet from the external world reach the original source as the packet with Dest IP = 10.1.1.1 will get lost as it can not be routed as many organizations can use the same IP. Why doesn't rfc 1918 (Address Allocation for Private Internets) make any mention of NAT?

  Read the article

• Cacti is not monitoring the correct host... How do I change SNMP target?

  - by wil

  I have been handed a Cacti server that monitors a few hosts. I noticed that three of the targets were displaying the exact same data - the cacti machine, machine a and machine b. After doing a bit of digging, I noticed that machine a and machine b had "Local Linux Machine" set under "Host Template". I have since changed the host template to "Generic SNMP-enabled Host", however, all the graphs still only display data from the local cacti machine (Updates every 5 minutes - I changed this yesterday - 12 hours). I can't think what else is wrong and was wondering if anyone knows/can recommend anything?

  Read the article

• How to use ssl_verify_client=ON on one virtual server and ssl_verify_client=OFF on another?

  - by Alexander Artemenko

  I want to force ssl client verification for on of my virtual hosts. But get "No required SSL certificate was sent" error, trying to GET something from it. Here are my test configs: # defaults ssl_certificate /etc/certs/server.cer; ssl_certificate_key /etc/certs/privkey-server.pem; ssl_client_certificate /etc/certs/allcas.pem; server { listen 1443 ssl; server_name server1.example.com; root /tmp/root/server1; ssl_verify_client off; } server { listen 1443 ssl; server_name server2.example.com; root /tmp/root/server2; ssl_verify_client on; } First server replies with 200 http code, but second returns "400 Bad Request, No required SSL certificate was sent, nginx/1.0.4". Probably, it is implossible to use ssl_verify_client on the same IP? Should I bind these servers to different IPs, will it solve my problem?

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• Hosting a site on amazon ec2

  - by Khalid Mushtaq

  I have recently bought an amazon ec2 instance. Now I want to host a website. I have googled and found some useful info but there is some confusion in my mind. Suppose domain name is "http://www.example.com" That's what I have done so far. I have configured my domain locally on amazon ec2 instance and it's working fine when I open that url in amazon ec2 instance's browser. I have used http://www.example.com in /etc/hosts file point it to 127.0.0.1 to open locally on instance. I have got one elastic ip address and associated it with the instance. I have changed http://www.example.com A's record with the elastic IP that I have got in above step. Now what should I do? When some user will open my website anywhere in the world, will it get pointed to my instanace's ip address? Have I done proper configurations for website on instance?

  Read the article

• Daemons die with bus error when their binaries live on NFS

  - by mbac32768

  We have some daemons executing on a number of hosts. The daemon executable images are these very large binaries that are hosted on NFS. When the binaries are updated on the NFS server, the previously running daemons sometimes drop dead with a Bus error. I'm assuming what's happening is the NFS server is replacing the binaries in a way that's invisible to the VFS layer on the NFS clients so they end up loading pages from the updated binary, which of course leads to madness. We tried moving the new binaries into place instead of cp, but that doesn't seem to fix it. I'm considering simply mlock()'ing the binary in the daemon startup script, but surely there's magic NFS options or semantics that we should be abusing. Is there a better way to fix this?

  Read the article

• Google Apps for Business on a separate infrastructure?

  - by dustin

  Does anyone know if Google Apps for Business edition hosts the apps (gmail, calendar, etc.) on a physically separate infrastructure than the Standard (free) infrastructure? We've been growing increasingly annoyed with the lost/severely delayed email messages, downtime, etc. of Google Apps (standard) over time, and we are wondering if moving to the paid version would bring any benefits. Specifically, if the Business edition is not in some way on a different physical infrastructure, and we are in essence paying for a few small perks but still run on the usual standard/free setup, then we would probably have the same (or just as many) issues with the Business version. I've emailed Google's sales team responsible for GApps, but haven't heard anything back in 4 days, which already doesn't speak well for the service. So, anyone have any insight into this? Thanks in advance for any and all help :)

  Read the article

• How to redirect from one web directory to another with Apache

  - by RN

  Apache2 Plesk 9.x I have a website www.example.com and my blog is on www.example.com/blog I have no content on www.example.com as of now So I want all requests for example.com to be redirected to www.example.com/blog How should I do that ? Is this something I can do in Apache? I am using the GoDaddy DNS server. Not sure if it matters- but I have multiple domains hosted n the same server. And I am using Plesk to manage my virtual hosts.

  Read the article

• i am not able to connect to the application hosted on port 80

  - by shiva

  I am trying to access an application that is hosted on port 80. When i try the url from my personal computer , the site is not reachable but the same url on the server( which hosts the application) i am able to access the site. When i disable the firewall then i am able to access the site from my pc. So there is some rule which is blocking this port. How do i determine what windows firewall rule is blocking this port. I have disables IIS as well. Kindly point me in the right direction

  Read the article

• 2 GPUs (for multi-monitor setup)

  - by A Dwarf

  I have a machine to which I need to connect a second monitor. This machine currently hosts a ATI Radeon HD 4770 with two DVI adapters. The second monitor to be hooked to this machine is a VGA monitor. Until I find a DVI-VGA adpater, I'm thinking installing a second graphics card which does have a VGA adapter, an NVidia card. Can I successfully run both AMD and NVidia cards on this machine? Any specifics I must be aware of, like how to ensure the ATI card to be the main card? Operating system is Windows 7

  Read the article

• IIS cannot access itself

  - by dave

  We are on a corporate network that uses ISA and I am having issues trying to not have requests go through ISA. I have IIS7 on my local Windows 7 machine that has websites and a service layer. The websites access the service layer using a xxxx.servicelayer.local address that is set up in my HOSTS file to point to 127.0.0.1. I have Windows Firewall client which I have disabled. I have tried both adding this address into IE so that it does not go through ISA and also disabled this section altogether. When the website (which is actually IIS making the request to itself) tries to access the service layer I receive an ISA error that proxy authentication has failed. Considering that everything I can see to configure is set to not go through the proxy, ISA, I cannot see how this is actually going through the proxy and giving this error. Is there something within Windows 7 that forces the proxy setting, some sort of caching or similar?

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >