Search Results

Search found 690 results on 28 pages for 'routers'.

Page 18/28 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

  • latency, regular alternations. Pfsense, network

    - by Tillebeck
    Any idea why grapgh is a shown? It i two pfsense boxes and I have not looked into where they ping to and if it is related to the server they ping. Trafic graphs are following a normal 24 hour cycle and not related to either of the latency graphs Img1: High frequent ulteration in latency. Just started a few days back. Peaks are not perfectly regular but varies from 40min to 1hour Img2: This is a different router on another internet connection. Most of our routers shown this kind of latency graphs - so for our setup it is "normal". Please note that second graph is for a whole week and not just some hours

    Read the article

  • Cisco RV016 dual WAN and VPN setup

    - by sklr
    I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

    Read the article

  • Cisco RV016 dual WAN and VPN setup

    - by sklr
    I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

    Read the article

  • NAT : understanding about interconnection

    - by PITCHY
    English version below J'ai 2 routeurs A et B relié en série avec les ip respectives ( 10.0.0.1/30 10.0.0.2/30) sur le routeur A j'ai activé la fonction NAT avec un pool (200.0.0.1 - 200.0.0.15/28). Lorsque je sors je prends donc un ip du pool par exemple 200.0.0.10. Comment ça fonctionne sachant que ma nouvelle ip (200.0.0.10) ne se trouve pas sur le meme réseau que mon interface de destination (10.0.0.2)? English: I have 2 routers A and B, interconnected with a serial connection, with the ip's 10.0.0.1/30 for A and 10.0.0.2/30 for B. On router A NAT was activated with the pool 200.0.0.1 - 200.0.0.15/28. When connection to this router, I get an ip from the pool, for example 200.0.0.10. Knowing my new ip is 200.0.0.10, which is not on the same network as my destination interface (10.0.0.2), how can this work?

    Read the article

  • Routing between two subnets. (Need Solution)

    - by rehanplus
    Need help according to scenario given: Client end PCs: 400 + Network : Server 1 (Linux) : 192.168.2.0/24 (For Application, Internet not working) GW: 192.168.2.1 Clients: 192.168.2.1 - 254 Server 2 (Linux) : 192.168.3.0/24 (For Internet users) GW: 192.168.3.1 Clients: 192.168.3.2 - 254 Server 2 is connected to DSL Broadband. Server 1 and Server 2 both are on same physical network i.e. Same switches. Current issue: i have to deploy a file and print server but this server will be accessed by both (192.168.2.x and 192.168.3.x) one same workgroup. as both subnets are on same switched network. Limitations: Currently there is no hardware routers and firewall. Need to complete this task with Linux / Windows / AD. Tested / Worked so far: Configured one PC with two NIC's With the IPS: NIC 1 : 192.168.3.2 GW: 192.168.3.1 Subnet: 255.255.255.0 NIC 2 : 192.168.2.2 GW: Empty Subnet: 255.255.255.0 Kindly provide any solution what should i do to get sharing enable on both Subnets. Thank you All

    Read the article

  • 8 Character Device names

    - by Lee Harrison
    Is there any reason to still use only 8 characters in a device name? My boss still uses this rule for printers, computers, routers, servers... basicly any device connected to our network. This leads to massive confusion among users, especially when it comes to printer. It also leads to confusion from an administration standpoint because every device is named vaguely, and similarly(its only 8 characters!). I understand the history behind this and compatibility with older systems, but none of our legacy systems will ever make use of PS-printers and Wifi networks. Is there any reason to still do this, and what is everyone else doing when it comes to naming network devices at an enterprise level?

    Read the article

  • vmware player - ubuntu can resolve hostname but ping fails

    - by recursive_acronym
    Using VMware players on Windows 7 with a Ubuntu 10.04 guest. When I ping it resolves the ip address but the ping fails. Hopefully this is a local issue as I don't have access to any of the network equipment (routers, etc). vmware tools is installed. Is there any other information I can provide to help resolve this? eth0 Link encap:Ethernet HWaddr 00:0c:29:83:4f:c0 inet addr:192.168.163.129 Bcast:192.168.163.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe83:4fc0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:50006 (50.0 KB) TX bytes:16701 (16.7 KB) Interrupt:19 Base address:0x2024 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B)

    Read the article

  • Question regarding IPv6 - Solicited-Node Address with a Link local scope

    - by Pulse
    Situation: A small LAN comprising a Windows 7 Ultimate x54 PC, 2 XP Pro x86 PCs and an Asus router.The Win 7 box has IPv6 enabled. There are no other IPv6 enabled devices on the LAN. In my firewall I see numerous requests originating from the Win 7 PC, which are for the Multicast address ff02::1:ff.... which is a Solicited-Node address query and has a scope of 2 which equates to the local link. As far as I knew local link addresses are filtered by routers, hence local link. Given that situation I'm wondering why I'm seeing these queries being generated to various addresses? Any ideas? Thanks.

    Read the article

  • Asus RT-N66U forgets USB-Printer

    - by heysamhey
    about a week ago I bought the new Asus RT-N66U as the new Router in our little company. There are about 5 clients and 2 printers. There's a USB-only printer as well, therefor we bougth a router with USB-printer sharing. The setup and everything works smooth, but then after one day, and I still haven't found out why, suddenly the printer dosen't show up in the list of connected devices in the routers webinterface anymore. Of course I loose the possibility of printig, even though the printer shows up as "online" in the system settings. Can anybody guess the reason for this problem? Thank you very much

    Read the article

  • is it possible in this case to get two IPv6 networks to communicate over the IPv4 Internet?

    - by user239167
    I have a setup of a laptop connected to a cellular IPv4 network (3G usb dongle) and PC connected to another IPv4/IPv6 network. Both have been configured to run as IPv6 routers and each has its IPv6 network. The laptop connects to the Internet via the 3G network with IPv4 address (private one and it is mostly changing) on one interface and has the other interface on AP mode providing its own private IPv6 network (2001:db8:444::/64). The PC connects to the Internet via the organization network with both public IPv4 and IPv6 addresses on one interface and has the other interface on AP mode providing its own private IPv6 network (2001:db8:222::/64). Both running Linux Ubuntu. Is it possible to get the two IPv6 network (2001:db8:222::/64 and 2001:db8:444::/64) to communicate over the IPv4 Internet? Is openvpn of any good in this case to get IPv6 traffic over IPv4-IPv4 tunnel? Thanks for helping in advance

    Read the article

  • Dns works, can ping, but cannot load web pages in browser

    - by user1224595
    Yesterday I changed routers, and my desktop computer started acting up. I could ping websites, and nslookup was able to resolve names to addresses, but neither chrome, firefox, nor ie could load any webpages. None of my other computers connected to the same wireless router have any problems. I connect my desktop to the router through a cheap wifi dongle. I did a wireshark capture of the browser request, and I have uploaded the pcap here. https://drive.google.com/file/d/0B7AsPdhWc-SwbTV0bUJLQXo4UUE/edit?usp=sharing One strange thing I noticed was the spamming of ssdp packets. I am not super familiar with networking, but it seems that it is not a problem with the router, as dns works, and so does dhcp (the desktop is assigned an address correctly). Any help would be appreciated.

    Read the article

  • one of my web hostings is down - only for me - why ?

    - by Thomas Traub
    My first post here, I am reading / learning a lot, thanks ;). I've got a mysterious issue (for me) and would really appreciate to get it solved. I've rent a reseller package with bibihost.com and it's now the second time that all my domaines the hoster's site are unavailable from my connection (my Mac and my iPhone), (in browser, per FTP, ping, ab, and traceroute) This has never before happened to me with other web addresses. traceroute get's always stuck at a specific server 40g.vss-1-6k.routers.chtix.eu (91.121.131.29) The sites are all up for everyone else, I've checked with downforeveryoneorjustme.com, a homegrown script loaded to another server and montastic.com My question(s) : Why am I blocked ? Is there anything I can do about it ? If I cannot solve this issue I have to change the hoster, but I really would like to know what's going on. my domaines on this server : tienstiens.fr tomlegrand.com

    Read the article

  • VoIP and IPv6 with IPsec

    - by PhilCisco
    Hi, I had some basic questions about VoIP in a IPv6 architecture, right now I'm running VoIP in a v4 architecture, and I was thinking about to change everything to v6. my questions are not that practical but I would like to understand it well. Question 1: if i had internet full v6 or v4 and that I enable IPsec on my v6 router do I still need a VPN through the internet ? because my routers will anyway exchange their pub/priv key or their certificate to ensure the communication. Question 2: If the answer to question 1 is yes then I only have two advantages to put my VoIP architecture to IPv6 the second advantage for me is the NAT which I will not have anymore. I know that right now I should anyway still use things like NAT-PT, Tunnelling and so one but in full v6 are their any other advantages ? Thank you

    Read the article

  • Can ping cannot be pinged

    - by slayerIQ
    Today, I installed my new router so I can connect my other pc and my ps3. In my network, there are some other computers these are connected with each other through another router. So I have one modem with 2 routers that make up my network. Everything works fine the only problem I am having is being pinged by other computers in the network. All the computers are on the same subnet 255.255.255.0. There is no problem with my firewall or anything I tested everything. How can i solve this?

    Read the article

  • How does 301 redirection work across the network? & should I use it if there is a chance we made need to change the resource back to the original URL?

    - by Faust
    I've built a CMS that makes it fairly easy for my client to relocate pages in their site hierarchy. This site has all human-readable and intuitive URLs, so moving a page necessarily means that its URL changes. I am storing records of each resource's past URLs in the data store so that requests for bygone URLs are re-routed to their appropriate successors. I'm warning my clients not to re-arrange the site willy-nilly (for numerous reasons). But nevertheless I suspect there's a chance page moves could get reversed from time to time. So I'm trying to figure out whether 301 or 302 or 307 redirects should be used when serving up pages to requests for out-of-date URLs. I understand the value of using 301 for search engine optimization. But my concern is with this system possibly inadvertently making some pages unavailable to some users QUESTIONS: That is, if the clients move a page at location/URL A to a new location B, then users get the redirect for A to B, and then the clients move the page back to A again, how long can I expect any of those users to keep getting their requests for A redirected to B -- in this case sending them to my friendly 404 page? Is it until an item in their browser history is cleared? Is the redirect somehow cached in routers throughout the internet? How does this work? How long can I expect the 301 redirect to linger out there ?

    Read the article

  • Wireless Bridge -DHCP

    - by Usta
    I was thinking of picking up a couple of TP-Link wireless routers, and setting them to bridge. I have a sep. LAN network that would have one of them, and I'd put one on my internet connection. Would I be able to keep my current IP subnets? (255.255.255.0 and 255.0.0.0) or would I have to pull my IPs from the same IP range. (I want to keep my current DHCP servers in place) The reason I want a bridge is so that I can VPN into the internal network.

    Read the article

  • Vhost in Apache only working locally?

    - by Gasman
    Ok, I have added lines like: 127.0.0.1 somedomain.com Or some other domain that points to my routers IP, and is forwarded, but I get to the main site, but I want it to go to the subfolder I defined in my httpd-vhosts.conf: NameVirtualHost somedomain.com:80 <VirtualHost somedomain.com:80> DocumentRoot "D:/Apps/xampp/htdocs/somedomain" ServerName somedomain.com ServerAlias somedomain.com </VirtualHost> So, locally somedomain.com works, just remotely it goes to the root htdocs. So If I use a *:80 wildcard I works, but then everything points to the subfolder and all the other vhosts seem to get ignored. Any Idea why this is?

    Read the article

  • Does anyone know of a inexpensive NAT router that has the ability to limit access to the Internet to

    - by Corey
    Does anyone know of a inexpensive NAT router that has the ability to limit access to the Internet to a specific MAC address? I know the Linksys routers have a MAC filtering feature, but it is the opposite of what I need. It allows you to block access to a specific MAC address. I need something that will block all, but allow an exception. I'm dealing with some VOIP issues in my company's network, and I think the answer is to have a separate router on the network for my PBX to use. I want to make sure that other nodes are not allowed to access the Internet via this second router.

    Read the article

  • My Router is fast when i reset it but slows down seconds later

    - by hglocke
    I have a Belkin N wireless router which until recently worked perfectly fine. Now i have to reset the router every few minutes, otherwise it slows down to a crawl. What can I do? I have tried turning the routers firewall off, but it does not make any difference. As far as I'm aware there have been no recent firmware updates. EDIT: The other devices on my network (laptop and iphone) do not have this problem. I connect to the router using a TP-Link wireless network card and I have already tried uninstalling and installing the driver. Hopefully this will narrow down the problem significantly.

    Read the article

  • Ubuntu in Virtualbox - web server very slow when using local IP address

    - by Lenny Marnham
    I'm using Ubuntu (Lucid Lynx) to learn Ruby On Rails. I'm running Ubuntu in VirtualBox (the host is Windows 7 Ultimate), using bridged networking. When I run my Rails app and point the browser at it using localhost:3000, the app responds immediately and my page is rendered in a second or two. However, if I use 10.0.0.5:3000 (where 10.0.0.5 is my IP address reported using ifconfig), the response from my rails app is incredibly slow - maybe 30 seconds or more for the server to respond and render the page. This happens in both Firefox and Chrome. Also, when I hit the Rails app from the host (to test it in IE), I get the same slooooooow response. Any ideas what might be going on? I've tried it with two different routers, and on two different networks (work and home) with the same result. Cheers all.

    Read the article

  • Change ip route metric

    - by notphunny
    I'm constantly switching between eth0 and wlan0 interface on my archlinux because I often change OpenWrt fw images on my second router (which isn't connected anywhere). So I have problem with my routes when I'm connected to my wlan and want to connect with Ethernet to my router. Both routers are on 192.168.1.1/24 and after connecting to my Ethernet profile eth0 route becomes default one (which is ok for the time), because of smaller metric I guess. So I'm interested, how can I change routes metric so my applications can be connected to the internet (through out wlan)? Maybe there is solution not to use Default Gateway on Ethernet profile, however I still want to know how to change metric. Or default route if there are more then one.

    Read the article

  • list and explanations of ways to boost this router's signal strength? [closed]

    - by barlop
    Possible Duplicates: Improve Wireless Signal How to get wireless coverage over my whole house? What's the best way to increase the range of my 802.11g router? The back of my house doesn't have WiFi Signal I'm interested in ways that are both specific to certain routers, and generic. When I say generic, I don't necessarily mean a one way that works for many.. but it can also be a generic answer, so mentioning solutions for different situations. So not just the one router I mention. Explanations are important, as well as all the ways. One i'm particularly interested in boosting the strength of is this wireless router/modem Netgear VMDG280 maybe anywhere in a big house with three floors, maybe from the garden.

    Read the article

  • Windows 7 - saved wifi access points disappear from list

    - by KáGé
    I'm having a weird issue with Windows 7 x64: I'm moving my notebook between two locations weekly, at each I have a wifi router. They both have hidden SSID-s, which are different. If I save one, the other one gets deleted from the list, as if overwritten, so I always have to retype the SSID and password, if I want to connect after moving my computer. At first I tought the problem was caused by both routers having the same password, but after I changed one (suffixed it with "_2") it persisted. What can I do about this? Thanks.

    Read the article

  • Using a Token-ring network card instead of a router (?)

    - by John
    I have cable, and the modem only has 1 network plug-in. They said I could buy my own router if I wanted to hook up two computers to it. I have an IBM Turbo 16/4 Token-Ring PC Card 2, which was in the laptop when I bought it, and the laptop also has the typical network plug (not a PC Card). Is there a way I could run the laptop as a server, and plug my desktop into the laptop, so they both have internet without my having to buy a router? (I realize routers are as cheap as $30.) Both computers run Windows XP Pro SP3. (I also have an 10/100 Etherjet Cardbus card (PC Card)). Thanks.

    Read the article

  • hosting website on a private network

    - by razor
    i'm currently running a website off 3 linux servers. I'd like to setup a private network and only allow port 80 traffic to one of the servers. I'd also like to setup a vpn so only I can access the servers via ssh or any port for developing/debugging. How hard is this to setup and what do I need to get? Do enterprise/commercial routers have vpn functionality built in? how do I handle DNS? eg- www.mydomain.com would need to point to the router, which forwards traffic to the webserver. Do I set the A record to the router, and somehow tell the router which server to send the http request to? And how would I make server1.mydomain.com resolve to server1 within the private network (without editing host files)? Would I need to run my own DNS (eg- powerdns?) to do this?

    Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >