Search Results

Search found 1877 results on 76 pages for 'vendor'.

Page 18/76 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• Unable to mount an LVM Hard-drive after upgrade

  - by Bruce Staples

  I imagine this is a basic gotcha ... but I can't see it. I have a system with 2(physical) harddrives. The boot system (/dev/sda) was running 10.04 & the second drive (/dev/sdb) was just a mounted filesystem. I did a clean load of Ubuntu 12.04 overwriting /dev/sda (not an upgrade) & now cannot mount the second drive. so I do not know what to enter it into the fstab ... I had expected to use: /dev/sdb /tera ext4 defaults 0 2 But even manual mounting fails (I also have tried various "-t" options on the off chance!) sudo mount -t ext4 /dev/sdb1 /tera mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Output from disk queries indicate that it is a Linux LVM & a healthy disk still. sudo lshw -C disk *-disk:0 description: ATA Disk product: WDC WD5000AACS-0 vendor: Western Digital physical id: 0 bus info: scsi@2:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WCASU1401098 size: 465GiB (500GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00015a55 *-disk:1 description: ATA Disk product: WDC WD10EADS-00L vendor: Western Digital physical id: 1 bus info: scsi@3:0.0.0 logical name: /dev/sdb version: 01.0 serial: WD-WCAU47836304 size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sudo fdisk -l Disk /dev/sda: 500.1 GB, 500106780160 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976771055 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00015a55 Device Boot Start End Blocks Id System /dev/sda1 * 2048 972580863 486289408 83 Linux /dev/sda2 972582910 976769023 2093057 5 Extended /dev/sda5 972582912 976769023 2093056 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1953525167 976762583+ 8e Linux LVM LVM doesn't appear to be an option for mount or fstab. ... and here's a Smart data Screenshot from Disk Utility.

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• Hello PCI Council, are you listening?

  - by David Dorf

  Mention "PCI" to any retailer and you'll instantly see them take a deep breath and start looking for the nearest exit.  Nobody wants to be insecure, but few actually believe that PCI does anything more than focus blame directly on retailers.  I applaud PCI for making retailers more aware of the importance of security, but did you have to make them PAINFULLY aware?  POS vendors aren't immune to this pain either as we have to undergo lengthy third-party audits in addition to the internal secure programming programs.  There's got to be a better way. There's a timely article over at StorefrontBacktalk that discusses the inequity of PCI's rules, and also mentions that the PCI Council is accepting comments until April 15th. As a vendor, my biggest issue with PCI is that they require vendors to disclose the details of any breaches, in effect "ratting out" customers.  I don't think its a vendor's place to do this.  I'd rather have the trust of my customers so we can jointly solve the problem. Mary Ann Davidson, Oracle's Chief Security Officer, has an interesting blog posting on this very topic.  Its a bit of a long read, but I found it very entertaining and thought-provoking.  Here's an excerpt: ...heading up the list of “you must be joking” regulations are recent disturbing developments in the Payment Card Industry (PCI) world. I’d like to give [the] PCI kahunas the benefit of the doubt about their intentions, except that efforts by Oracle among others to make them aware of “unfortunate side effects of your requirements” – which is as tactful I can be for reasons that I believe will become obvious below - have gone, to-date, unanswered and more importantly, unchanged. I encourage you to read the entire posting, Pain Comes Instantly, and then provide feedback to the PCI Council.

  Read the article

• Define a Policykit action for Upstart

  - by gentakojima

  I'm trying to get some user to start, stop and reload services by using the udev Upstart interface. I'm using Ubuntu 10.04. I created the file /usr/share/polkit-1/actions/com.ubuntu.Upstart0_6.Job.policy <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE policyconfig PUBLIC "-//freedesktop//DTD PolicyKit Policy Configuration 1.0//EN" "http://www.freedesktop.org/standards/PolicyKit/1.0/policyconfig.dtd"> <policyconfig> <vendor>UXITIC</vendor> <vendor_url>http://citius.usc.es/</vendor_url> <icon_name>gdm</icon_name> <action id="com.ubuntu.Upstart0_6.Job.Stop"> <_description>Stops a service</_description> <_message>Privileges are required to stop a service.</_message> <defaults> <allow_inactive>no</allow_inactive> <allow_active>auth_admin_keep</allow_active> </defaults> </action> </policyconfig> And also the corresponding authority file /etc/polkit-1/localauthority/50-local.d/10-allow-users-to-start-and-stop-services.pkla [Stop services] Identity=unix-user:jorge Action=com.ubuntu.Upstart_0.6.Job.Stop ResultAny=no ResultInactive=no ResultActive=auth_self But when I try to stop a service, I get Access Denied :( jorge$ dbus-send --print-reply --system --dest=com.ubuntu.Upstart /com/ubuntu/Upstart/jobs/ssh com.ubuntu.Upstart0_6.Job.Stop array:string:'' boolean:true Error org.freedesktop.DBus.Error.AccessDenied: Rejected send message, 1 matched rules; type="method_call", sender=":1.452" (uid=1021 pid=28234 comm="dbus-send) interface="com.ubuntu.Upstart0_6.Job" member="Stop" error name="(unset)" requested_reply=0 destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init"))

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• How do I know if I'm getting the most out of my video card?

  - by b.long

  My computer at home is a bit lacking, so I want to make sure I'm getting the most out of it while I can. Generally speaking, here are the specs: 4GB Memory AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ × 2 64-bit Ubuntu The terminal shows me the following: me@home:~$ uname -a Linux home 3.0.0-17-generic #30-Ubuntu SMP Thu Mar 8 20:45:39 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux me@home:~$ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] me@home:~$ sudo lshw -C video *-display:0 description: VGA compatible controller product: RV380 [Radeon X600 (PCIE)] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:44 memory:e0000000-efffffff ioport:ac00(size=256) memory:fdef0000-fdefffff memory:fdec0000-fdedffff *-display:1 UNCLAIMED description: Display controller product: RV380 [Radeon X600] vendor: ATI Technologies Inc physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress bus_master cap_list configuration: latency=0 resources: memory:fdee0000-fdeeffff me@home:~$ lspci -nn | grep VGA 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] [1002:5b62] The additional drivers menu in System Settings shows me nothing useful and my attempt at installing ATI's Catalyst Control center (drivers that came with the video card) failed. I believe the latest version of Ubuntu at the time was 9.x. What should I do? Install an old version of Ubuntu 9? Use some alternative driver? UPDATE: I might try my hand at a bit from this answer next: "Installing Catalyst Manually (from AMD/ATI's site)" . From a terminal, fgl_glxgears returns *"fgl_glxgears: command not found"*. Any thoughts?

  Read the article

• Desktop goes blurry / granulated

  - by Bonfire

  After few minutes using, desktop and fonts in unity-menu goes blurry. See screenshot.! In all applications (browser etc.) graphics seem to be allright. After rebooting problem disappears for few minutes. Changing the wallpaper also makes the desktop clear (for a while) but fonts are still blurry. I have ubuntu 12.04 and windows xp dualbooted. lspci: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:02.1 Display controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) lshw -c video: *-display:0 description: VGA compatible controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:16 memory:d0100000-d017ffff ioport:30c0(size=8) memory:c0000000-cfffffff memory:d0180000-d01bffff *-display:1 UNCLAIMED description: Display controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 02 width: 32 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:40000000-4007ffff Have you got any ideas to get this solved? Thank you very much! Bonfire

  Read the article

• USB flash module giving errors

  - by vshenoy

  Hi, I have a SATA USB flash module which was earlier running a 2.4 linux kernel (2.4.36.6) and on which now I am trying to install ubuntu server 10.04.1 LTS. I have two such USB flash modules and on one of them the installation process itself giving these errors: sd 4:0:0:0 [sda] Device not ready sd 4:0:0:0 [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 4:0:0:0 [sda] Sense Key : Not Ready [current] sd 4:0:0:0 [sda] Add. Sense: Medium not present sd 4:0:0:0 [sda] CDB: Write(10): 2a 00 00 05 48 02 00 00 04 00 end_request: I/O error, dev sda, sector 46114 usb 1-1: reset high speed USB device using ehci_hcd and address 2 Buffer I/O error on device sda1, logical block 172033 lost page write due to I/O error on sda1 Buffer I/O error on device sda1, logical block 172034 lost page write due to I/O error on sda1 on the other the installation is successful, but after a day or two of running the machine hangs because of kernel spewing these messages: Remounting filesystem read-only EXT2-fs error (device sda1): read_block_bitmap: Cannot read block [bitmap - block_group = 105, block_bitmap = 860161] EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=13083, block=24683 ext2_free_inode: bit already cleared for inode 83966 and the machine needs to be hard rebooted. On both the systems SCSI emulation with usb_storage driver is being used to detect the module. Here is the output of /proc/scsi/scsi on 2.4: # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 02 and on 2.6: # cat /proc/scsi/scsi Attached devices: Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 i.e. only 'ANSI SCSI revision:' is shown as different, although I am not sure if this can cause any problem. Really appreciate if someone can point as to how to debug this issue or any mailing list where I can further ask questions about this.

  Read the article

• Wireless drivers

  - by Kencer

  The results for my laptop are as below. How will i install wireless drivers and graphics? $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) $ sudo lshw -c network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0500000-f0507fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 07 serial: 3c:97:0e:85:c0:0d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=172.16.96.36 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• Cannot view, use, or open CDs or DVDs in Ubuntu 12.04

  - by user67592

  I am fairly new to Ubuntu 12.04 and I have encountered a rather irritating problem. Whenever I insert a CD or DVD (whether it have data, music, movies, or nothing at all), nothing pops up saying "you have inserted a CD", "play with Rhythmbox?" etc. It doesn't show the CD in the launcher/dock or anything of the sort. This is especially peculiar because not only do I have a standard IDE built-in optical drive, but I have an external USB optical drive. Neither work. In addition, whenever I go to "Computer///" and I click (double click, right click, or even left click) on "CD/DVD Drive" nothing happens, when I right click and select "Open" nothing happens either [for either of the two drives (both are listed in Computer///)] And if I insert a blank disk and go to a disk burning program such as Brasero, and try to burn to the drive it detects no CDs or DVDs of any kind. I'm rather stumped and can't seem to find a question similar to this. :( Thanks for all your help in advance!! :) ~Preston Output of sudo lshw *-cdrom description: DVD-RAM writer product: CD/DVDW TS-H652M vendor: TSSTcorp physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 0414 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom description: DVD reader product: DVD Writer 300n vendor: HP physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/sr1 version: 1.25 serial: [ capabilities: removable audio cd-r cd-rw dvd configuration: status=nodisc

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• Ubuntu 13.10, kernel 3.11 blank screen issue with hybrid graphics

  - by Lagerbaer

  On my HP Envy, which has both an Intel on-chip graphics card and an Nvidia Geforce: *-display UNCLAIMED description: 3D controller product: GK208M [GeForce GT 740M] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:d2000000-d2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:5000(size=128) memory:b2000000-b207ffff *-display description: VGA compatible controller product: 4th Gen Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d3000000-d33fffff memory:c0000000-cfffffff ioport:6000(size=64) I have trouble with all newer kernels. I basically had to install 12.04 LTS and use their 3.5 kernel family to get the system to boot. The 3.8 from 12.10 or the newest 3.11 from Ubuntu 13.10 leave me with a black screen upon boot. On one occasion I did hear the "log in" sound, but the screen did not display anything. I have purged all nvidia drivers so I guess it should just use the intel drivers, but apparently this is all messed up with newer kernel versions. This is different from the other "nvidia boots into blank screen" bug in that I don't rely solely on an nvidia card. Surely the intel on-chip card should be supported and leave me with something different from a blank screen? Again, it only works with kernel versions 3.5.0-41-generic, not with the 3.11.0-12 one that ships with Ubuntu 13.10. When I go into the grub menu and change the boot options from 'quiet splash' to 'nomodeset' I am able to boot the system, but then I don't get any graphics and trying 'sudo service lightdm start' doesn't succeed (I get 100% CPU for apport, but this doesn't do anything either, so I kill it). Help, I'm all out of ideas. EDIT: Let me add that I'm using the EFI boot system and have a dual-boot installation with Windows 8.

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• Partition does not start on physical sector boundary?

  - by jasmines

  I've one HD on my laptop, with two partitions (one ext3 with Ubuntu 12.04 installed and one swap). fdisk is giving me a Partition 1 does not start on physical sector boundary warning. What is the cause and do I need to fix it? If so, how? This is sudo fdisk -l: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 testine, 63 settori/tracce, 91201 cilindri, totale 1465149168 settori Unità = settori di 1 * 512 = 512 byte Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Identificativo disco: 0x5a25087f Dispositivo Boot Start End Blocks Id System /dev/sda1 * 63 1448577023 724288480+ 83 Linux Partition 1 does not start on physical sector boundary. /dev/sda2 1448577024 1465147391 8285184 82 Linux swap / Solaris This is sudo lshw related result: *-disk description: ATA Disk product: WDC WD7500BPKT-0 vendor: Western Digital physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WX21CC1T0847 size: 698GiB (750GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=5a25087f *-volume:0 description: EXT3 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: cc5c562a-bc59-4a37-b589-805b27b2cbd7 size: 690GiB capacity: 690GiB capabilities: primary bootable journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-27 09:18:28 filesystem=ext3 modified=2012-06-23 18:33:59 mount.fstype=ext3 mount.options=rw,relatime,errors=remount-ro,user_xattr,barrier=1,data=ordered mounted=2012-06-28 00:20:47 state=mounted *-volume:1 description: Linux swap volume physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 version: 1 serial: 16a7fee0-be9e-4e34-9dc3-28f4eeb61bf6 size: 8091MiB capacity: 8091MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 These are related /etc/fstab lines: UUID=cc5c562a-bc59-4a37-b589-805b27b2cbd7 / ext3 errors=remount-ro,user_xattr 0 1 UUID=16a7fee0-be9e-4e34-9dc3-28f4eeb61bf6 none swap sw 0 0

  Read the article

• Dim (NEARLY blank) laptop screen, secondary screen works - why?

  - by LIttle Ancient Forest Kami

  My laptop screen is (almost) black while my secondary screen is fine. I believe it to be backlight / brightness related. Problem description it starts when I start the laptop system loads and works fine, just screen has problems I can see the screen though very faintly / dimly - it's hard to see anything which ain't very white e.g. starting screen has big Thinkpad logo in white, large font - I can see it, though very dimly second screen works very well Official backligtht debugging: using acpi setting as prescribed there for Thinkpads didn't help I can see an entry in /sys/class/backlight/ and it changes when I press hotkeys for brightness (current backlight power for instance goes up or down) acpi-off didn't helpm neither did acpi_backlight=vendor Hardware data Laptop is Thinkpad Edge with glossy screen. 4 processors, 2 cores, exemplary CPU data from cat /proc/cpuinfo reports Genuine Intel i5 (M 480 @ 2.67GHz). OS is Ubuntu Lucid, 10.04 LTS, 64-bit, with Linux generic kernel (2.6.32-44) and GNOME 2.32.2 (though I doubt there lies the problem). $ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] $ lshw -C display *-display description: VGA compatible controller product: M92 [Mobility Radeon HD 4500 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:33 memory:c0000000-dfffffff(prefetchable) ioport:2000(size=256) memory:f0300000-f030ffff memory:f0320000-f033ffff(prefetchable) Driver I was NOT running any proprietary drivers, just checked with "Hardware drivers". There is one for ATI that is suggested there, though I didn't need it so far. UPDATE: changing the driver to proprietary one (ATI/AMD FGLRX) didn't help. Tried and failed Resetting / running on power or battery / charging / getting rid of static electricity / warming up *doesn't help* This is NOT a blank-screen problem, at least it isn't following official Ubuntu black-screen diagnostics - I can see my screen, though barely. What I will try next: - check last updates I've made - IIRC I am running on nomodeset already, but will verify this Any ideas how to proceed best? What is most probable cause?

  Read the article

• alsa - sound issues on ubuntu 12.04

  - by tam_ubuuser

  i am having an sony E series laptop.i have an HDMI port .at this stage ,i have tested my sound card , which provides audio out on my laptop i.e i could hear songs .my laptop has two sound cards amd 5450 and an intel-hda(alsamixer shows that as s/pdif) . i decided to connect HDMI output to my new HD-TV.but, i could get only visuals on my TV,NO AUDIO OUTPUT ( HDMI cable works fine with win 7).my laptop has two sound cards.but i couldn't switch output to other card.( i don't know ,how to do that) i decided to update alsa. complied the following code in terminal. sudo apt-add-repository ppa:ubuntu-audio-dev/alsa-daily sudo apt-get update sudo apt-get install alsa-hda-dkms then,strangely no login sound, and no audio output on my laptop at all .then, started complied code from step1 sound troubleshooting procedure from offical ubuntu site.then, my speaker icon taskbar disappeared .obivously $aplay -l ,provided output as no soundcards detected . so , i implemented step 4 from that guide, it provides a output of all hardware devices in my laptop. *-multimedia UNCLAIMED description: Audio device product: Cedar HDMI Audio [Radeon HD 5400/6300 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: latency=0 resources: memory:f0040000-f0043fff *-multimedia UNCLAIMED description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f5e00000-f5e03fff that command displayed output name of the two cards . but , still i have no positive output on $aplay -l. so therfore, i think alsa couldn't detect my sound cards . is there solution to this problem? it could be better,if alsa would channel output from multiple sound cards ? how should install and configure alsa such that detects HDMI cable as soon i connect to my HD tv? is it possible to alsa and pluseaudio 2.0 to co-exist, if so how?

  Read the article

• Driver for asus wireless PC card WL-100GE

  - by emab

  I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• 2 folders in Sys/Class/Backlight?

  - by zebrapie

  ISSUE: Backlight brightness does not change. More Detail: Brightness will not change, using both 'System Settings-Screen', or FN keys (Brightness bar shows and moves, but screen brightness does not change). Notcied a post in this thread (http://ubuntuforums.org/showthread.php?t=1866283) about having multiple folders in Sys-Class-Backlight... I HAVE TWO FOLDERS TOO! 'intel_backlight' and 'acpi_video0' Using the function keys, alters the value in the acpi_video0's 'Brightness' file - But doesn't actually alter the brightness of the screen. If I add 'backlight=vendor' in Grub, my function keys then edit the value in the 'Intel_Backlight brightness file. - But again doesnt actually change the brightness of the screen. Computer: Fujitsu Siemans Pi2515, Intel Integrated Graphics, No hdd partition. Already Tried: -Editing grub to contain: acpi_osi=Linux acpi_backlight=vendor -http://ubuntuguide.net/change-screen-brightness-with-fn-key-in-ubuntu-11-0410-10 -sudo apt-get install acpi -$ sudo setpci -s 00:02.0 F4.B=20 -Brightness does not adjust in fallback mode either. -Reinstalling OS, Using Linux Mint (Same problem). -Upgrading and downgrading BIOS. Many thanks for reading, I understand this problem may need a bit of a Linux pro to sort. If anyones up for the challenge i'll spend any amount of time being walked through this, posting results. Don't want to give up here!

  Read the article

• ubuntu 11.10 can't find wireless after waking from sleep

  - by Colleen

  I've tried a lot of proposed solutions, most of them adding files to /etc/pm/config.d, as well as WiFi stops working after waking from suspend and nothing has worked. hardware info: [colleen@colleen-HP ~]$ sudo lshw -C network [sudo] password for colleen: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:b1:ea:67 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:4000(size=256) memory:c1404000-c1404fff memory:c1400000-c1403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 8c:a9:82:99:48:8c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-21-generic-pae firmware=39.31.5.1 build 35138 ip=192.168.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:c5500000-c5501fff Is anyone else still having this problem? The two solutions I haven't tried are installing wicd and upgrading because I've heard both are kind of unstable/buggy and wicd frankly scares me.

  Read the article

• Unable to enable wireless in ubuntu 12.04

  - by Joe

  I have a Vostro 2520 and not sure how to enable wireless on my machine. The details are given below, would appreciate any pointers to resolving this issue. lsmod returns Module Size Used by ath9k 132390 0 ath9k_common 14053 1 ath9k ath9k_hw 411151 2 ath9k,ath9k_common ath 24067 3 ath9k,ath9k_common,ath9k_hw b43 365785 0 mac80211 506816 2 ath9k,b43 cfg80211 205544 4 ath9k,ath,b43,mac80211 bcma 26696 1 b43 ssb 52752 1 b43 ndiswrapper 282628 0 ums_realtek 18248 0 usb_storage 49198 1 ums_realtek uas 18180 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_cirrus 24002 1 joydev 17693 0 parport_pc 32866 0 ppdev 17113 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep psmouse 97362 0 dell_wmi 12681 0 sparse_keymap 13890 1 dell_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq wmi 19256 1 dell_wmi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device mac_hid 13253 0 i915 473240 3 drm_kms_helper 46978 1 i915 uvcvideo 72627 0 drm 242038 4 i915,drm_kms_helper videodev 98259 1 uvcvideo soundcore 15091 1 snd dell_laptop 18119 0 dcdbas 14490 1 dell_laptop i2c_algo_bit 13423 1 i915 v4l2_compat_ioctl32 17128 1 videodev snd_page_alloc 18529 2 snd_hda_intel,snd_pcm video 19596 1 i915 serio_raw 13211 0 mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 sudo lshw -class network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7c00000-f7c07fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 07 serial: 78:45:c4:a3:aa:65 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.1.5 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:e000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: yes

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >