Search Results

Search found 1886 results on 76 pages for 'vendor neutrality'.

Page 18/76 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• Centrino Wireless-N 1000 takes forever to connect and keeps asking for password

  - by waclock

  A few days ago I started having this problem. When I tried to connect to any WiFi Connection it would stay connecting forever, and after a minute or so it would ask me for the password again. The strange thing is that this happened out of nowhere, I did not install any new drivers or anything like that. After this happened I decided to uninstall ubuntu and install it again ("inside windows") but the problem is still there. Any suggestions would be greatly appreciated. 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:aa:e4:7d size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:50 ioport:4000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:09:9c:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-23-generic-pae firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:c4500000-c4501fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.2 logical name: eth1 serial: ee:85:2f:7d:80:96 capabilities: ethernet physical configuration: broadcast=yes driver=ipheth ip=172.20.10.2 link=yes multicast=yes

  Read the article

• How to make Unity 3D work with Bumblebee using the Intel chipset

  - by EboMike

  I have a Sony VAIO S laptop with the dreaded Optimus and finally managed to get Bumblebee to work fully on Ubuntu 12.04 so that I can utilize both the hardware acceleration of the Intel chipset as well as the Nvidia one via optirun and/or bumble-app-settings. However, the desktop effects don't work. But they should, I vaguely remember that they worked for a while before I had Bumblebee installed. This is what I get with the support test: :~$ /usr/lib/nux/unity_support_test -p Xlib: extension "NV-GLX" missing on display ":0". OpenGL vendor string: Tungsten Graphics, Inc OpenGL renderer string: Mesa DRI Intel(R) Ivybridge Mobile OpenGL version string: 1.4 (2.1 Mesa 8.0.2) Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: no GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no First of all, I kind of doubt that the chipset doesn't support VBOs (essentially a standard feature in GL). Neither Xorg.0.log nor Xorg.8.log show any particular errors. As for the Nvidia drivers: In order to get them to work, I had to install the 304.22 drivers (older ones wouldn't work). They clobbered libglx.so, so I reinstated the xserver-xorg-core libglx.so in its original place, moved Nvidia's libglx.so to an nvidia-specific folder and specified that folder in the bumblebee.config. That seems to work and shouldn't cause the problem I see here. For fun, I tried to use the Nvidia chipset for Unity, but that didn't fly either: ~$ optirun /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce GT 640M LE/PCIe/SSE2 OpenGL version string: 4.2.0 NVIDIA 304.22 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: no GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Can I set my Optimus Nvidia card to run Unity3D with bumblebee?

  - by manuhalo

  I'd like to know whether I can run compiz on my Nvidia card to speed things up. It's a Dell XPS15 laptop but I'm mostly using it as a desktop, so battery life is not important. Apparently my Intel integrated card is able to run unity 3D, but my Nvidia GT 420M is not. Here's the output of unity_support_test, both with optirun and without it: manuhalo@Ubuntu-XPS-L501X:~$ optirun /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce GT 420M/PCI/SSE2 OpenGL version string: 4.1.0 NVIDIA 280.13 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: no GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no manuhalo@Ubuntu-XPS-L501X:~$ /usr/lib/nux/unity_support_test -p OpenGL vendor string: Tungsten Graphics, Inc OpenGL renderer string: Mesa DRI Intel(R) Ironlake Mobile OpenGL version string: 2.1 Mesa 7.11 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: yes Any ideas of why this is happening? Thanks in advance to anyone able to shed some light on this. What I have tried: Installed the v290 drivers from the x-stable PPA. Tried forcing Unity-3D to work by telling Unity to ignore the unity-support-test results i.e. gksudo gedit /etc/environment add the following UNITY_FORCE_START=1 to the end of the file.

  Read the article

• How do I get Graphics drivers / bluetooth / card reader working on an Acer Aspire V3-571G?

  - by Adam

  A couple of days ago I bought an Acer Aspire V3-571G laptop without a system installed on it. The only thing that was there was Linux Linpus. I created a bootable CD with Ubuntu 12.04 64-bit - I read that my processor was 64 bit and that it might be a good configuration for my gear (I'm not especially fluent with all the computer stuff, still trying to learn) and replaced Linpus with Ubuntu. Everything seemed to work fine, but there're few exceptions to that which came pass my way. My bluetooth doesn't work. It seems to be switched on, but when I check my system settings the button is actually off, and I can't drag it 'perminently' to the 'on' position. Tried a couple of commands I found on the net, none of them helped and there was no word whatsoever in my BIOS settings about enabling bluetooth. My card reader has some serious problems with copying more than one file at a time. I tried to put some music on my phone through a MicroSD card adapter (because my bluetooth doesn't work) and it got stuck every single time I copied an album on it. I'm not sure if all my drivers were properly installed, so I checked in the terminal if it could tell me sth about my graphics. typed: sudo lshw -c display and what i got was: *-display UNCLAIMED description: VGA compatible controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller cap_list configuration: latency=0 resources: memory:b2000000-b2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:2000(size=128) *-display description: VGA compatible controller product: Ivy Bridge Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:b3000000-b33fffff memory:c0000000-cfffffff ioport:3000(size=64) As I said I'm no expert and not english-speaking generally, but it doesn't seem to be right. I've got a NVIDIA GeForce GT 640M.

  Read the article

• How do I install 10.04 on a Vortex86DX embdedded system?

  - by mathematician1975

  I am trying to install Ubuntu on a Netcom NC-499 board that contains a Vortex86DX processor. The processor vendor claims support for Ubuntu 10.04 but I am having problems installing it. I am trying to install to a 8GB compact flash card attached to the board with an IDE connector, using a USB connection CD-Rom drive and a burned ISO image obtained from this link http://old-releases.ubuntu.com/releases/10.04.0/ubuntu-10.04.3-desktop-i386.iso . Installation proceeds up to the point of around 78% but during the stage where the installer informs me that it is "configuring apt", the installer terminates with a popup dialog containing the following "The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again." I have no idea what to do at this point. I am a Linux novice and I do not really know how to investigate the problems with the installation. I have configured the BIOS exactly according to how the vendor specifies and they assure me that this version is fully compatible with their hardware and yet I am unable to get a decent install. I am able to install Ubuntu 8.04 using exactly the same procedure successfully so I am sure there is no problem with my CD-Rom compatibility or the compact flash drive. Any help will be gratefully received.

  Read the article

• Discs in DVD Drive not being read

  - by I Heart Ubuntu

  Does anyone have an experience with Ubuntu that is no longer reading discs in the DVD drive? This is my first time Ubuntu does not see the disc :| The disc is fine and works on my other Ubuntu computers. The drive is there and powered. I can even type in eject in a terminal and the drive will open. Using the command: sudo lshw -C disk I am able to see info about my drive too. Actually BOTH of my internal DVD drives cannot read discs anymore. If the output is not readable below, here is the info in pastebin. http://pastebin.com/GqqSCTPw *-cdrom:0 description: DVD writer product: DVD_RW ND-3500AG vendor: _NEC physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/cdrom1 logical name: /dev/cdrw1 logical name: /dev/dvd1 logical name: /dev/dvdrw1 logical name: /dev/scd0 logical name: /dev/sr0 version: 2.1B serial: [_NEC DVD_RW ND-3500AG2.1B06022300BT-LIGGY capabilities: removable audio cd-r cd-rw dvd dvd-r configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: CDDVDW SH-S222A vendor: TSSTcorp physical id: 0.1.0 bus info: scsi@0:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: SB01 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc

  Read the article

• Is this a dual monitor reset bug?

  - by Tentresh

  My two displays are: Intel GMA x4500 Laptop (1280x800 native resolution of the built-in display) External display (1920x1080) A few minutes after I login to my dual monitor setup, it gets reset to mirror screens. If I restore the settings via the displays application, everything is fine. On each reset, the following messages are written into /var/log/Xorg.0.log: [ 60.852] (II) PM Event received: Capability Changed [ 60.852] I830PMEvent: Capability change [ 132.920] (II) intel(0): EDID vendor "SEC", prod id 12869 [ 132.920] (II) intel(0): Printing DDC gathered Modelines: [ 132.920] (II) intel(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz) [ 134.228] (II) intel(0): Allocated new frame buffer 1280x800 stride 5120, tiled Whereas right on startup or manual resolution reset, /var/log/Xorg.0.log reports the expected frame buffer allocation: [ 1562.382] (II) intel(0): EDID vendor "SEC", prod id 12869 [ 1562.382] (II) intel(0): Printing DDC gathered Modelines: [ 1562.382] (II) intel(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz) [ 1576.740] (II) intel(0): Allocated new frame buffer 3200x1080 stride 12800, tiled Is Ubuntu 12.04 not compatible with my video card? Can this be solved within Ubuntu? I like its interface, but manually fiddling with resolution on every login is not bearable.

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• Unable to mount an LVM Hard-drive after upgrade

  - by Bruce Staples

  I imagine this is a basic gotcha ... but I can't see it. I have a system with 2(physical) harddrives. The boot system (/dev/sda) was running 10.04 & the second drive (/dev/sdb) was just a mounted filesystem. I did a clean load of Ubuntu 12.04 overwriting /dev/sda (not an upgrade) & now cannot mount the second drive. so I do not know what to enter it into the fstab ... I had expected to use: /dev/sdb /tera ext4 defaults 0 2 But even manual mounting fails (I also have tried various "-t" options on the off chance!) sudo mount -t ext4 /dev/sdb1 /tera mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Output from disk queries indicate that it is a Linux LVM & a healthy disk still. sudo lshw -C disk *-disk:0 description: ATA Disk product: WDC WD5000AACS-0 vendor: Western Digital physical id: 0 bus info: scsi@2:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WCASU1401098 size: 465GiB (500GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00015a55 *-disk:1 description: ATA Disk product: WDC WD10EADS-00L vendor: Western Digital physical id: 1 bus info: scsi@3:0.0.0 logical name: /dev/sdb version: 01.0 serial: WD-WCAU47836304 size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sudo fdisk -l Disk /dev/sda: 500.1 GB, 500106780160 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976771055 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00015a55 Device Boot Start End Blocks Id System /dev/sda1 * 2048 972580863 486289408 83 Linux /dev/sda2 972582910 976769023 2093057 5 Extended /dev/sda5 972582912 976769023 2093056 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1953525167 976762583+ 8e Linux LVM LVM doesn't appear to be an option for mount or fstab. ... and here's a Smart data Screenshot from Disk Utility.

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• Hello PCI Council, are you listening?

  - by David Dorf

  Mention "PCI" to any retailer and you'll instantly see them take a deep breath and start looking for the nearest exit.  Nobody wants to be insecure, but few actually believe that PCI does anything more than focus blame directly on retailers.  I applaud PCI for making retailers more aware of the importance of security, but did you have to make them PAINFULLY aware?  POS vendors aren't immune to this pain either as we have to undergo lengthy third-party audits in addition to the internal secure programming programs.  There's got to be a better way. There's a timely article over at StorefrontBacktalk that discusses the inequity of PCI's rules, and also mentions that the PCI Council is accepting comments until April 15th. As a vendor, my biggest issue with PCI is that they require vendors to disclose the details of any breaches, in effect "ratting out" customers.  I don't think its a vendor's place to do this.  I'd rather have the trust of my customers so we can jointly solve the problem. Mary Ann Davidson, Oracle's Chief Security Officer, has an interesting blog posting on this very topic.  Its a bit of a long read, but I found it very entertaining and thought-provoking.  Here's an excerpt: ...heading up the list of “you must be joking” regulations are recent disturbing developments in the Payment Card Industry (PCI) world. I’d like to give [the] PCI kahunas the benefit of the doubt about their intentions, except that efforts by Oracle among others to make them aware of “unfortunate side effects of your requirements” – which is as tactful I can be for reasons that I believe will become obvious below - have gone, to-date, unanswered and more importantly, unchanged. I encourage you to read the entire posting, Pain Comes Instantly, and then provide feedback to the PCI Council.

  Read the article

• Define a Policykit action for Upstart

  - by gentakojima

  I'm trying to get some user to start, stop and reload services by using the udev Upstart interface. I'm using Ubuntu 10.04. I created the file /usr/share/polkit-1/actions/com.ubuntu.Upstart0_6.Job.policy <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE policyconfig PUBLIC "-//freedesktop//DTD PolicyKit Policy Configuration 1.0//EN" "http://www.freedesktop.org/standards/PolicyKit/1.0/policyconfig.dtd"> <policyconfig> <vendor>UXITIC</vendor> <vendor_url>http://citius.usc.es/</vendor_url> <icon_name>gdm</icon_name> <action id="com.ubuntu.Upstart0_6.Job.Stop"> <_description>Stops a service</_description> <_message>Privileges are required to stop a service.</_message> <defaults> <allow_inactive>no</allow_inactive> <allow_active>auth_admin_keep</allow_active> </defaults> </action> </policyconfig> And also the corresponding authority file /etc/polkit-1/localauthority/50-local.d/10-allow-users-to-start-and-stop-services.pkla [Stop services] Identity=unix-user:jorge Action=com.ubuntu.Upstart_0.6.Job.Stop ResultAny=no ResultInactive=no ResultActive=auth_self But when I try to stop a service, I get Access Denied :( jorge$ dbus-send --print-reply --system --dest=com.ubuntu.Upstart /com/ubuntu/Upstart/jobs/ssh com.ubuntu.Upstart0_6.Job.Stop array:string:'' boolean:true Error org.freedesktop.DBus.Error.AccessDenied: Rejected send message, 1 matched rules; type="method_call", sender=":1.452" (uid=1021 pid=28234 comm="dbus-send) interface="com.ubuntu.Upstart0_6.Job" member="Stop" error name="(unset)" requested_reply=0 destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init"))

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• Desktop goes blurry / granulated

  - by Bonfire

  After few minutes using, desktop and fonts in unity-menu goes blurry. See screenshot.! In all applications (browser etc.) graphics seem to be allright. After rebooting problem disappears for few minutes. Changing the wallpaper also makes the desktop clear (for a while) but fonts are still blurry. I have ubuntu 12.04 and windows xp dualbooted. lspci: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:02.1 Display controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) lshw -c video: *-display:0 description: VGA compatible controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:16 memory:d0100000-d017ffff ioport:30c0(size=8) memory:c0000000-cfffffff memory:d0180000-d01bffff *-display:1 UNCLAIMED description: Display controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 02 width: 32 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:40000000-4007ffff Have you got any ideas to get this solved? Thank you very much! Bonfire

  Read the article

• How do I know if I'm getting the most out of my video card?

  - by b.long

  My computer at home is a bit lacking, so I want to make sure I'm getting the most out of it while I can. Generally speaking, here are the specs: 4GB Memory AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ × 2 64-bit Ubuntu The terminal shows me the following: me@home:~$ uname -a Linux home 3.0.0-17-generic #30-Ubuntu SMP Thu Mar 8 20:45:39 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux me@home:~$ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] me@home:~$ sudo lshw -C video *-display:0 description: VGA compatible controller product: RV380 [Radeon X600 (PCIE)] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:44 memory:e0000000-efffffff ioport:ac00(size=256) memory:fdef0000-fdefffff memory:fdec0000-fdedffff *-display:1 UNCLAIMED description: Display controller product: RV380 [Radeon X600] vendor: ATI Technologies Inc physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress bus_master cap_list configuration: latency=0 resources: memory:fdee0000-fdeeffff me@home:~$ lspci -nn | grep VGA 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] [1002:5b62] The additional drivers menu in System Settings shows me nothing useful and my attempt at installing ATI's Catalyst Control center (drivers that came with the video card) failed. I believe the latest version of Ubuntu at the time was 9.x. What should I do? Install an old version of Ubuntu 9? Use some alternative driver? UPDATE: I might try my hand at a bit from this answer next: "Installing Catalyst Manually (from AMD/ATI's site)" . From a terminal, fgl_glxgears returns *"fgl_glxgears: command not found"*. Any thoughts?

  Read the article

• Wireless drivers

  - by Kencer

  The results for my laptop are as below. How will i install wireless drivers and graphics? $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) $ sudo lshw -c network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0500000-f0507fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 07 serial: 3c:97:0e:85:c0:0d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=172.16.96.36 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• USB flash module giving errors

  - by vshenoy

  Hi, I have a SATA USB flash module which was earlier running a 2.4 linux kernel (2.4.36.6) and on which now I am trying to install ubuntu server 10.04.1 LTS. I have two such USB flash modules and on one of them the installation process itself giving these errors: sd 4:0:0:0 [sda] Device not ready sd 4:0:0:0 [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 4:0:0:0 [sda] Sense Key : Not Ready [current] sd 4:0:0:0 [sda] Add. Sense: Medium not present sd 4:0:0:0 [sda] CDB: Write(10): 2a 00 00 05 48 02 00 00 04 00 end_request: I/O error, dev sda, sector 46114 usb 1-1: reset high speed USB device using ehci_hcd and address 2 Buffer I/O error on device sda1, logical block 172033 lost page write due to I/O error on sda1 Buffer I/O error on device sda1, logical block 172034 lost page write due to I/O error on sda1 on the other the installation is successful, but after a day or two of running the machine hangs because of kernel spewing these messages: Remounting filesystem read-only EXT2-fs error (device sda1): read_block_bitmap: Cannot read block [bitmap - block_group = 105, block_bitmap = 860161] EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=13083, block=24683 ext2_free_inode: bit already cleared for inode 83966 and the machine needs to be hard rebooted. On both the systems SCSI emulation with usb_storage driver is being used to detect the module. Here is the output of /proc/scsi/scsi on 2.4: # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 02 and on 2.6: # cat /proc/scsi/scsi Attached devices: Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 i.e. only 'ANSI SCSI revision:' is shown as different, although I am not sure if this can cause any problem. Really appreciate if someone can point as to how to debug this issue or any mailing list where I can further ask questions about this.

  Read the article

• Cannot view, use, or open CDs or DVDs in Ubuntu 12.04

  - by user67592

  I am fairly new to Ubuntu 12.04 and I have encountered a rather irritating problem. Whenever I insert a CD or DVD (whether it have data, music, movies, or nothing at all), nothing pops up saying "you have inserted a CD", "play with Rhythmbox?" etc. It doesn't show the CD in the launcher/dock or anything of the sort. This is especially peculiar because not only do I have a standard IDE built-in optical drive, but I have an external USB optical drive. Neither work. In addition, whenever I go to "Computer///" and I click (double click, right click, or even left click) on "CD/DVD Drive" nothing happens, when I right click and select "Open" nothing happens either [for either of the two drives (both are listed in Computer///)] And if I insert a blank disk and go to a disk burning program such as Brasero, and try to burn to the drive it detects no CDs or DVDs of any kind. I'm rather stumped and can't seem to find a question similar to this. :( Thanks for all your help in advance!! :) ~Preston Output of sudo lshw *-cdrom description: DVD-RAM writer product: CD/DVDW TS-H652M vendor: TSSTcorp physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 0414 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom description: DVD reader product: DVD Writer 300n vendor: HP physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/sr1 version: 1.25 serial: [ capabilities: removable audio cd-r cd-rw dvd configuration: status=nodisc

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• Ubuntu 13.10, kernel 3.11 blank screen issue with hybrid graphics

  - by Lagerbaer

  On my HP Envy, which has both an Intel on-chip graphics card and an Nvidia Geforce: *-display UNCLAIMED description: 3D controller product: GK208M [GeForce GT 740M] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:d2000000-d2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:5000(size=128) memory:b2000000-b207ffff *-display description: VGA compatible controller product: 4th Gen Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d3000000-d33fffff memory:c0000000-cfffffff ioport:6000(size=64) I have trouble with all newer kernels. I basically had to install 12.04 LTS and use their 3.5 kernel family to get the system to boot. The 3.8 from 12.10 or the newest 3.11 from Ubuntu 13.10 leave me with a black screen upon boot. On one occasion I did hear the "log in" sound, but the screen did not display anything. I have purged all nvidia drivers so I guess it should just use the intel drivers, but apparently this is all messed up with newer kernel versions. This is different from the other "nvidia boots into blank screen" bug in that I don't rely solely on an nvidia card. Surely the intel on-chip card should be supported and leave me with something different from a blank screen? Again, it only works with kernel versions 3.5.0-41-generic, not with the 3.11.0-12 one that ships with Ubuntu 13.10. When I go into the grub menu and change the boot options from 'quiet splash' to 'nomodeset' I am able to boot the system, but then I don't get any graphics and trying 'sudo service lightdm start' doesn't succeed (I get 100% CPU for apport, but this doesn't do anything either, so I kill it). Help, I'm all out of ideas. EDIT: Let me add that I'm using the EFI boot system and have a dual-boot installation with Windows 8.

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >