Search Results

Search found 19125 results on 765 pages for 'hard disk'.

Page 185/765 | < Previous Page | 181 182 183 184 185 186 187 188 189 190 191 192  | Next Page >

• RAID controller dropping the wrong drive

  - by bramp

  I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

  Read the article

• What *exactly* gets screwed when I kill -9 or pull the power?

  - by Mike

  Set-Up I've been a programmer for quite some time now but I'm still a bit fuzzy on deep, internal stuff. Now. I am well aware that it's not a good idea to either: kill -9 a process (bad) spontaneously pull the power plug on a running computer or server (worse) However, sometimes you just plain have to. Sometimes a process just won't respond no matter what you do, and sometimes a computer just won't respond, no matter what you do. Let's assume a system running Apache 2, MySQL 5, PHP 5, and Python 2.6.5 through mod_wsgi. Note: I'm most interested about Mac OS X here, but an answer that pertains to any UNIX system would help me out. My Concern Each time I have to do either one of these, especially the second, I'm very worried for a period of time that something has been broken. Some file somewhere could be corrupt -- who knows which file? There are over 1,000,000 files on the computer. I'm often using OS X, so I'll run a "Verify Disk" operation through the Disk Utility. It will report no problems, but I'm still concerned about this. What if some configuration file somewhere got screwed up. Or even worse, what if a binary file somewhere is corrupt. Or a script file somewhere is corrupt now. What if some hardware is damaged? What if I don't find out about it until next month, in a critical scenario, when the corruption or damage causes a catastrophe? Or, what if valuable data is already lost? My Hope My hope is that these concerns and worries are unfounded. After all, after doing this many times before, nothing truly bad has happened yet. The worst is I've had to repair some MySQL tables, but I don't seem to have lost any data. But, if my worries are not unfounded, and real damage could happen in either situation 1 or 2, then my hope is that there is a way to detect it and prevent against it. My Question(s) Could this be because modern operating systems are designed to ensure that nothing is lost in these scenarios? Could this be because modern software is designed to ensure that nothing lost? What about modern hardware design? What measures are in place when you pull the power plug? My question is, for both of these scenarios, what exactly can go wrong, and what steps should be taken to fix it? I'm under the impression that one thing that can go wrong is some programs might not have flushed their data to the disk, so any highly recent data that was supposed to be written to the disk (say, a few seconds before the power pull) might be lost. But what about beyond that? And can this very issue of 5-second data loss screw up a system? What about corruption of random files hiding somewhere in the huge forest of files on my hard drives? What about hardware damage? What Would Help Me Most Detailed descriptions about what goes on internally when you either kill -9 a process or pull the power on the whole system. (it seems instant, but can someone slow it down for me?) Explanations of all things that could go wrong in these scenarios, along with (rough of course) probabilities (i.e., this is very unlikely, but this is likely)... Descriptions of measures in place in modern hardware, operating systems, and software, to prevent damage or corruption when these scenarios occur. (to comfort me) Instructions for what to do after a kill -9 or a power pull, beyond "verifying the disk", in order to truly make sure nothing is corrupt or damaged somewhere on the drive. Measures that can be taken to fortify a computer setup so that if something has to be killed or the power has to be pulled, any potential damage is mitigated. Thanks so much!

  Read the article

• Installer Reboots at "Detecting hardware" (disks and other hardware) on all recent Server Installs

  - by Ryan Rosario

  I have a very frustrating problem with my PC. I cannot install any recent version of Ubuntu Server (or even Desktop) since 9.04 even using the text-based installer. I boot from a USB stick created by Unetbootin (I also tried other methods such as startup disk creator with no difference). On the Server installer, it gets to "Detecting Hardware" (the second one about disks and all other hardware, not network hardware) and then either hangs at 0% (waited 24 hours), or reboots after a minute or two. My system (late 2007): ASUS P5NSLI motherboard Intel Core 2 Duo E6600 2.4Ghz 2 x 1GB Corsair 667MHz RAM nVidia GeForce 6600 I have unplugged everything (including the only hard disk, CD-ROMs and floppy). I have only one stick of RAM (tried each one to no avail) and am booting the installer from a USB stick (booting from CD-ROM yields the same problem). I also tried several of the boot options (nomodeset, nousb, acpi=off, noapic, i915.modeset=1/0, xforcevesa) in all combinations) to no avail. The only active parts of my system are the video card, mouse, keyboard and USB stick. I have also updated the BIOS to the most recent version. (FWIW, on the Desktop installer, I get a black screen after hitting the Install option.) Even after removing "quiet" I am unable to see what kernel panic is occurring (or not occurring) to cause the install to crash. I am only able to save the debug logs via a simple webserver in the installer. After the last line (I repeatedly refreshed), the server stops responding and the installer hangs or reboots: Jan 2 01:04:03 main-menu[302]: INFO: Menu item 'disk-detect' selected Jan 2 01:04:04 kernel: [ 309.154372] sata_nv 0000:00:0e.0: version 3.5 Jan 2 01:04:04 kernel: [ 309.154409] sata_nv 0000:00:0e.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.154531] sata_nv 0000:00:0e.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.164442] scsi0 : sata_nv Jan 2 01:04:04 kernel: [ 309.167610] scsi1 : sata_nv Jan 2 01:04:04 kernel: [ 309.167762] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 10 Jan 2 01:04:04 kernel: [ 309.167774] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 10 Jan 2 01:04:04 kernel: [ 309.167948] sata_nv 0000:00:0f.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.168071] sata_nv 0000:00:0f.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.171931] scsi2 : sata_nv Jan 2 01:04:04 kernel: [ 309.173793] scsi3 : sata_nv Jan 2 01:04:04 kernel: [ 309.173943] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 11 Jan 2 01:04:04 kernel: [ 309.173954] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 11 Jan 2 01:04:04 kernel: [ 309.174061] pata_amd 0000:00:0d.0: version 0.4.1 Jan 2 01:04:04 kernel: [ 309.174160] pata_amd 0000:00:0d.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.177045] scsi4 : pata_amd Jan 2 01:04:04 kernel: [ 309.178628] scsi5 : pata_amd Jan 2 01:04:04 kernel: [ 309.178801] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 Jan 2 01:04:04 kernel: [ 309.178811] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jan 2 01:04:04 kernel: [ 309.485062] ata3: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:04 kernel: [ 309.633094] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jan 2 01:04:04 kernel: [ 309.641647] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133 Jan 2 01:04:04 kernel: [ 309.641658] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32) Jan 2 01:04:04 kernel: [ 309.657614] ata1.00: configured for UDMA/133 Jan 2 01:04:04 kernel: [ 309.657969] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5 Jan 2 01:04:04 kernel: [ 309.658482] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 2 01:04:04 kernel: [ 309.658588] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Jan 2 01:04:04 kernel: [ 309.658812] sd 0:0:0:0: [sda] Write Protect is off Jan 2 01:04:04 kernel: [ 309.658823] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 2 01:04:04 kernel: [ 309.658918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 2 01:04:04 kernel: [ 309.675630] sda: sda1 sda2 Jan 2 01:04:04 kernel: [ 309.676440] sd 0:0:0:0: [sda] Attached SCSI disk Jan 2 01:04:05 kernel: [ 309.969102] ata2: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:05 kernel: [ 310.281137] ata4: SATA link down (SStatus 0 SControl 300) Anybody have any additional ideas I could try? I am getting ready to just toss the motherboard.

  Read the article

• Converting an Oracle VM VirtualBox VM into an Oracle VM Server image

  - by wim.coekaerts

  As we are working on tighter seemless moving of VM's between the 2 products, here are a few simple steps to convert an existing Oracle VM VirtualBox image over. Steps involved to make it easy/straightforward : (1) When creating a VM in Virtualbox, using Oracle Linux as an example, make sure that /etc/fstab only uses labels. Do not use hardcoded device names. instead of an entry /dev/sda1 /u01 ext3 defaults 1 1 use LABEL=foo /u01 ext3 defaults 1 1 for more info on labels : man e2label or use a logical volume /dev/VolGroup00/LVfoo /u01 ext3 defaults 1 1 Doing so will make it easier to have an OS boot up on a different hypervisor with potentially different device names. For instance, the VirtualBox VM might expose a scsi driver while in Oracle VM Server you might end up with an ide disk, this then changes /dev/sda to /dev/hda. (2) If you have a VM created that you want to convert, then shut down the VM in VirtualBox and convert the image files : go the the directory that contains your HardDisk image files (.VirtualBox/HardDisks/* as an example) for each of the virtual disks run the following command : VBoxManage clonehd virtualdiskfilename.vdi system.img --format raw where virtualdiskfilename.vdi is the original VBox VM file (this can also be a vmdk file) and system.img is the name of the virtualdisk for Oracle VM. this can be any filename as well, I typically use system.img to specify the boot disk (as is common for Oracle VM template creation) (3) create a vm.cfg To run a VM converted from VirtualBox, you have to create a vm.cfg for Oracle VM server that creates an HVM guest. The easiest is to use a simple hvm vm.cfg and change it for your vm. I have an example here : acpi = 1 apic = 1 builder = 'hvm' device_model = '/usr/lib/xen/bin/qemu-dm' disk = ['file:system.img,hda,w', 'file:oracle.img,hdb,w',',hdc:cdrom,r',] kernel = '/usr/lib/xen/boot/hvmloader' memory = '1024' name = 'vmname' on_crash = 'restart' on_reboot = 'restart' pae = 1 serial = 'pty' timer_mode = '0' usbdevice = 'tablet' vcpus = 1 vif = ['bridge=xenbr0,type=ioemu'] vif_other_config = [] vnc = 1 vncconsole = 1 vnclisten = '0.0.0.0' vncpasswd = '' vncunused = 1 If you take the above vm.cfg, all you need to do - modify disk = (add your virtual disks in there) - modify memory = (amount of memory your VM needs) - modify name = (enter a name for your VM here) - modify vif = (might want to replace bridge=xenbr0 to the bridge you want to use) if you want more than 1 vcpu or other changes of course you have to make those as well. (4) copy this set of files onto your Oracle VM server or onto a webserver in a subdirectory and import the template through Oracle VM Manager. You can also just start the vm using xm create vm.cfg if you like. And that's it. As I said, we are working on automation around all this but it is relatively trivial to convert VM's over as long as you take the basic issues into account. Primarily the set up of the filesystems and the use of labels in /etc/fstab. There are other potential things to look at, such as network config. If you want to make that part clean then prior to shutting down the VM change /etc/modprobe.conf and/or add the mac address of the VM into the vm.cfg in the vifs line. The good thing, at least with Linux, is that even tho the virtual hardware changes, Linux will deal with it just fine (e1000 vs 8139 realtek, ide vs scsi etc). hope this helps.

  Read the article

• BlueTooth not working on my HP Probook 4720s

  - by mtrento

  the blue tooth on my ubuntu 11.10 does not work. When i try to ad a device it scans indefinitely and never find anything. Wireless is working perfeclty and with windows 7 it is detected. As i read somewhere , the bluetooth is not listed in the usb devices. Is it supported under ubuntu? here are the output of the various debug command i tested : hciconfig -a hci0: Type: BR/EDR Bus: USB BD Address: E0:2A:82:7A:8B:04 ACL MTU: 310:10 SCO MTU: 64:8 UP RUNNING PSCAN ISCAN RX bytes:1895 acl:0 sco:0 events:70 errors:0 TX bytes:1986 acl:0 sco:0 commands:64 errors:0 Features: 0xff 0xff 0x8f 0xfe 0x9b 0xff 0x59 0x83 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH HOLD SNIFF PARK Link mode: SLAVE ACCEPT Name: 'PC543host-0' Class: 0x5a0100 Service Classes: Networking, Capturing, Object Transfer, Telephony Device Class: Computer, Uncategorized HCI Version: 2.1 (0x4) Revision: 0x149c LMP Version: 2.1 (0x4) Subversion: 0x149c Manufacturer: Cambridge Silicon Radio (10) hcitool scan hcitool scan Scanning ... lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b1ac Chicony Electronics Co., Ltd Bus 002 Device 003: ID 413c:3010 Dell Computer Corp. Optical Wheel Mouse Bus 002 Device 004: ID 148f:1000 Ralink Technology, Corp. lsmod | grep -i bluetooth bluetooth 166112 23 bnep,rfcomm,btusb dmesg | grep -i bluetooth [ 18.543947] Bluetooth: Core ver 2.16 [ 18.544017] Bluetooth: HCI device and connection manager initialized [ 18.544020] Bluetooth: HCI socket layer initialized [ 18.544021] Bluetooth: L2CAP socket layer initialized [ 18.545469] Bluetooth: SCO socket layer initialized [ 18.548890] Bluetooth: Generic Bluetooth USB driver ver 0.6 [ 30.204776] Bluetooth: RFCOMM TTY layer initialized [ 30.204782] Bluetooth: RFCOMM socket layer initialized [ 30.204784] Bluetooth: RFCOMM ver 1.11 [ 30.247291] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 30.247295] Bluetooth: BNEP filters: protocol multicast lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 05) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 05) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 05) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5400 Series] 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] 44:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe 45:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 3: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• WiFi stops working after a while in Lenovo ThinkPad W520 (Ubuntu 12.04)

  - by el10780

  After several minutes(I do not know how many) there is no internet connection on my laptop via Wi-Fi.Ubuntu doesn't show any kind of message that my WiFi was disconnected neither there is a signal drop,but suddenly Firefox stops connecting to web pages.I checked my modem/router and it seems that it is working fine.I tried also to reboot the WiFi device and nothing happens.The only thing that it makes it work again is a reboot of the system and if I do not want to do a reboot then I am enforced to connect to the Internet using Ethernet cable.Does anybody know what is happening? ## Some Hardware info that might be helpful ## el10780@ThinkPad-W520:~$ sudo lshw -class network *-network description: Ethernet interface product: 82579LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 04 serial: f0:de:f1:f1:be:10 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k duplex=full firmware=0.13-3 ip=192.168.0.10 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:50 memory:f3a00000-f3a1ffff memory:f3a2b000-f3a2bfff ioport:6080(size=32) *-network description: Wireless interface product: Centrino Advanced-N + WiMAX 6250 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 5e serial: 64:80:99:63:14:74 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=41.28.5.1 build 33926 ip=192.168.0.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:52 memory:f3900000-f3901fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.3 logical name: wmx0 serial: 00:1d:e1:53:b2:e8 capabilities: ethernet physical configuration: driver=i2400m firmware=i6050-fw-usb-1.5.sbcf link=no el10780@ThinkPad-W520:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) 00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) 03:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e) 0d:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 08) 0d:00.3 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 PCIe IEEE 1394 Controller (rev 04) 0e:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) el10780@ThinkPad-W520:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: i2400m-usb:2-1.3:1.0: WiMAX Soft blocked: yes Hard blocked: no The weirdest thing is this screenshot which I took after running the **Additional Drivers** program.I mean I have a NVidia Quadro 1000M and my Intel Centrino WiFi Card and this shows that there are not proprietay drivers for my system. http://imageshack.us/photo/my-images/268/screenshotfrom201207062.png/

  Read the article

• How do I repair the corrupted files found by sfc /scannow? "Windows Resource Protection found corrupt files but was unable to fix some of them."

  - by galacticninja

  After running chkdsk C: /F /R and finding out that my hard disk has 24 KB in bad sectors (log is posted below), I decided to run Windows 7's System File Checker utility (sfc /scannow). SFC showed the ff. message after I ran it: "Windows Resource Protection found corrupt files but was unable to fix some of them. Details are included in the CBS.Log windir\Logs\CBS\CBS.log." Since the CBS.log file is too large, I ran findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt" (as per Microsoft's KB 928228 article) to only get the log text pertaining to the corrupt files. (log is also posted below) How do I troubleshoot and repair the corrupted files mentioned by sfc /scannow? My OS is Windows 7, 64-bit. chkdsk log Checking file system on C: The type of the file system is NTFS. A disk check has been scheduled. Windows will now check the disk. CHKDSK is verifying files (stage 1 of 5)... 936192 file records processed. File verification completed. 25238 large file records processed. 0 bad file records processed. 4 EA records processed. 44 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 1051640 index entries processed. Index verification completed. 0 unindexed files scanned. 0 unindexed files recovered. CHKDSK is verifying security descriptors (stage 3 of 5)... 936192 file SDs/SIDs processed. Cleaning up 24 unused index entries from index $SII of file 0x9. Cleaning up 24 unused index entries from index $SDH of file 0x9. Cleaning up 24 unused security descriptors. Security descriptor verification completed. 57725 data files processed. CHKDSK is verifying Usn Journal... 36994248 USN bytes processed. Usn Journal verification completed. CHKDSK is verifying file data (stage 4 of 5)... 936176 files processed. File data verification completed. CHKDSK is verifying free space (stage 5 of 5)... 306238 free clusters processed. Free space verification is complete. Adding 1 bad clusters to the Bad Clusters File. Correcting errors in the Volume Bitmap. Windows has made corrections to the file system. 488282111 KB total disk space. 485595420 KB in 766458 files. 401856 KB in 57726 indexes. 24 KB in bad sectors. 1059863 KB in use by the system. 65536 KB occupied by the log file. 1224948 KB available on disk. 4096 bytes in each allocation unit. 122070527 total allocation units on disk. 306237 allocation units available on disk. Internal Info: 00 49 0e 00 81 93 0c 00 34 01 17 00 00 00 00 00 .I......4....... 6b 29 00 00 2c 00 00 00 00 00 00 00 00 00 00 00 k)..,........... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ sfc /scannow log (through findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt") Note: The full log is at http://pastebin.com/raw.php?i=gTEGZmWj . I've only quoted parts of the full log below (mostly from the last part), as the full log won't fit within the character limit for questions. I've added it to serve as a preview. ... 2013-12-28 19:37:50, Info CSI00000542 [SR] Beginning Verify and Repair transaction 2013-12-28 19:37:55, Info CSI00000544 [SR] Verify complete 2013-12-28 19:37:56, Info CSI00000545 [SR] Verifying 95 (0x000000000000005f) components 2013-12-28 19:37:56, Info CSI00000546 [SR] Beginning Verify and Repair transaction 2013-12-28 19:38:03, Info CSI00000548 [SR] Verify complete 2013-12-28 19:38:03, Info CSI00000549 [SR] Repairing 43 (0x000000000000002b) components 2013-12-28 19:38:03, Info CSI0000054a [SR] Beginning Verify and Repair transaction ... 2013-12-28 19:38:15, Info CSI00000730 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:62{31}]"GroupPolicy-Admin-Gpedit-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000733 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:30{15}]"frs-core-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000736 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:26{13}]"gpmgmt-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000739 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:74{37}]"MediaServer-ASPAdmin-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000073c [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:36{18}]"Ldap-Client-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000073f [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:38{19}]"iSNS_Service-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000742 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:76{38}]"MediaServer-Multicast-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000745 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:78{39}]"Kerberos-Key-Distribution-Center-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000748 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:86{43}]"GroupPolicy-CSE-SoftwareInstallation-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000074b [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:28{14}]"ieframe-dl.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000074e [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:76{38}]"GroupPolicy-Admin-Gpedit-Snapin-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000751 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:32{16}]"IPSec-Svc-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000754 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:22{11}]"HTTP-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000757 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:56{28}]"MediaServer-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000075a [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:26{13}]"GPBase-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000075d [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:38{19}]"IasMigPlugin-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000760 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:50{25}]"International-Core-DL.man"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000762 [SR] Cannot repair member file [l:24{12}]"wbemdisp.dll" of Microsoft-Windows-WMI-Scripting, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000763 [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI00000766 [SR] Could not reproject corrupted file [ml:58{29},l:56{28}]"\??\C:\Windows\SysWOW64\wbem"\[l:24{12}]"wbemdisp.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000768 [SR] Cannot repair member file [l:56{28}]"Microsoft.MediaCenter.UI.dll" of Microsoft.MediaCenter.UI, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_MSIL (8), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000769 [SR] This component was referenced by [l:176{88}]"Microsoft-Windows-MediaCenter-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.MediaCenter" 2013-12-28 19:38:16, Info CSI0000076c [SR] Could not reproject corrupted file [ml:520{260},l:40{20}]"\??\C:\Windows\ehome"\[l:56{28}]"Microsoft.MediaCenter.UI.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI0000076e [SR] Cannot repair member file [l:24{12}]"ReAgentc.exe" of Microsoft-Windows-WinRE-RecoveryTools, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI0000076f [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI00000772 [SR] Could not reproject corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:24{12}]"ReAgentc.exe"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000774 [SR] Cannot repair member file [l:82{41}]"System.Management.Automation.dll-Help.xml" of Microsoft-Windows-PowerShell-PreLoc.Resources, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture = [l:10{5}]"en-US", VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000775 [SR] This component was referenced by [l:266{133}]"Microsoft-Windows-Client-Features-Package~31bf3856ad364e35~amd64~en-US~6.1.7601.17514.Microsoft-Windows-Client-Features-Language-Pack" 2013-12-28 19:38:16, Info CSI00000778 [SR] Could not reproject corrupted file [ml:520{260},l:104{52}]"\??\C:\Windows\System32\WindowsPowerShell\v1.0\en-US"\[l:82{41}]"System.Management.Automation.dll-Help.xml"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI0000077a [SR] Cannot repair member file [l:18{9}]"hlink.dll" of Microsoft-Windows-HLink, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI0000077b [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI0000077e [SR] Could not reproject corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:18{9}]"hlink.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000780 [SR] Repair complete 2013-12-28 19:38:16, Info CSI00000781 [SR] Committing transaction 2013-12-28 19:38:19, Info CSI00000785 [SR] Verify and Repair Transaction completed. All files and registry keys listed in this transaction have been successfully repaired

  Read the article

• MySQL query, 2 similar servers, 2 minute difference in execution times

  - by mr12086

  I had a similar question on stack overflow, but it seems to be more server/mysql setup related than coding. The queries below all execute instantly on our development server where as they can take upto 2 minutes 20 seconds. The query execution time seems to be affected by home ambiguous the LIKE string's are. If they closely match a country that has few matches it will take less time, and if you use something like 'ge' for germany - it will take longer to execute. But this doesn't always work out like that, at times its quite erratic. Sending data appears to be the culprit but why and what does that mean. Also memory on production looks to be quite low (free memory)? Production: Intel Quad Xeon E3-1220 3.1GHz 4GB DDR3 2x 1TB SATA in RAID1 Network speed 100Mb Ubuntu Development Intel Core i3-2100, 2C/4T, 3.10GHz 500 GB SATA - No RAID 4GB DDR3 UPDATE 2 : mysqltuner output: [prod] -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.61-0ubuntu0.10.04.1 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 103M (Tables: 180) [--] Data in InnoDB tables: 491M (Tables: 19) [!!] Total fragmented tables: 38 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 77d 4h 6m 1s (53M q [7.968 qps], 14M conn, TX: 87B, RX: 12B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 58.0M global + 2.7M per thread (151 max threads) [OK] Maximum possible memory usage: 463.8M (11% of installed RAM) [OK] Slow queries: 0% (12K/53M) [OK] Highest usage of available connections: 22% (34/151) [OK] Key buffer size / total MyISAM indexes: 16.0M/10.6M [OK] Key buffer hit rate: 98.7% (162M cached / 2M reads) [OK] Query cache efficiency: 20.7% (7M cached / 36M selects) [!!] Query cache prunes per day: 3934 [OK] Sorts requiring temporary tables: 1% (3K temp sorts / 230K sorts) [!!] Joins performed without indexes: 71068 [OK] Temporary tables created on disk: 24% (3M on disk / 13M total) [OK] Thread cache hit rate: 99% (690 created / 14M connections) [!!] Table cache hit rate: 0% (64 open / 85M opened) [OK] Open file limit used: 12% (128/1K) [OK] Table locks acquired immediately: 99% (16M immediate / 16M locks) [!!] InnoDB data size / buffer pool: 491.9M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) join_buffer_size (> 128.0K, or always use indexes with joins) table_cache (> 64) innodb_buffer_pool_size (>= 491M) [dev] -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.62-0ubuntu0.11.10.1 [!!] Switch to 64-bit OS - MySQL cannot currently use all of your RAM -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 185M (Tables: 632) [--] Data in InnoDB tables: 967M (Tables: 38) [!!] Total fragmented tables: 73 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 2h 26m 9s (5K q [0.058 qps], 1K conn, TX: 4M, RX: 1M) [--] Reads / Writes: 99% / 1% [--] Total buffers: 58.0M global + 2.7M per thread (151 max threads) [OK] Maximum possible memory usage: 463.8M (11% of installed RAM) [OK] Slow queries: 0% (0/5K) [OK] Highest usage of available connections: 1% (2/151) [OK] Key buffer size / total MyISAM indexes: 16.0M/18.6M [OK] Key buffer hit rate: 99.9% (60K cached / 36 reads) [OK] Query cache efficiency: 44.5% (1K cached / 2K selects) [OK] Query cache prunes per day: 0 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 44 sorts) [OK] Temporary tables created on disk: 24% (162 on disk / 666 total) [OK] Thread cache hit rate: 99% (2 created / 1K connections) [!!] Table cache hit rate: 1% (64 open / 4K opened) [OK] Open file limit used: 8% (88/1K) [OK] Table locks acquired immediately: 100% (1K immediate / 1K locks) [!!] InnoDB data size / buffer pool: 967.7M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: table_cache (> 64) innodb_buffer_pool_size (>= 967M) UPDATE 1: When testing the queries listed here there is usually no more than one other query taking place, and usually none. Because production is actually handling apache requests that development gets very few of as it's only myself and 1 other who accesses it - could the 4GB of RAM be getting exhausted by using the single machine for both apache and mysql server? Production: sudo hdparm -tT /dev/sda /dev/sda: Timing cached reads: 24872 MB in 2.00 seconds = 12450.72 MB/sec Timing buffered disk reads: 368 MB in 3.00 seconds = 122.49 MB/sec sudo hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 24786 MB in 2.00 seconds = 12407.22 MB/sec Timing buffered disk reads: 350 MB in 3.00 seconds = 116.53 MB/sec Server version(mysql + ubuntu versions): 5.1.61-0ubuntu0.10.04.1 Development: sudo hdparm -tT /dev/sda /dev/sda: Timing cached reads: 10632 MB in 2.00 seconds = 5319.40 MB/sec Timing buffered disk reads: 400 MB in 3.01 seconds = 132.85 MB/sec Server version(mysql + ubuntu versions): 5.1.62-0ubuntu0.11.10.1 ORIGINAL DATA : This query is NOT the query in question but is related so ill post it. SELECT f.form_question_has_answer_id FROM form_question_has_answer f INNER JOIN project_company_has_user p ON f.form_question_has_answer_user_id = p.project_company_has_user_user_id INNER JOIN company c ON p.project_company_has_user_company_id = c.company_id INNER JOIN project p2 ON p.project_company_has_user_project_id = p2.project_id INNER JOIN user u ON p.project_company_has_user_user_id = u.user_id INNER JOIN form f2 ON p.project_company_has_user_project_id = f2.form_project_id WHERE (f2.form_template_name = 'custom' AND p.project_company_has_user_garbage_collection = 0 AND p.project_company_has_user_project_id = '29') AND (LCASE(c.company_country) LIKE '%ge%' OR LCASE(c.company_country) LIKE '%abcde%') AND f.form_question_has_answer_form_id = '174' And the explain plan for the above query is, run on both dev and production produce the same plan. +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ | id | select_type | table | type | possible_keys | key | key_len | ref | rows | Extra | +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ | 1 | SIMPLE | p2 | const | PRIMARY | PRIMARY | 4 | const | 1 | Using index | | 1 | SIMPLE | f | ref | form_question_has_answer_form_id,form_question_has_answer_user_id | form_question_has_answer_form_id | 4 | const | 796 | Using where | | 1 | SIMPLE | u | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using index | | 1 | SIMPLE | p | ref | project_company_has_user_unique_key,project_company_has_user_user_id,project_company_has_user_company_id,project_company_has_user_project_id | project_company_has_user_user_id | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using where | | 1 | SIMPLE | f2 | ref | form_project_id | form_project_id | 4 | const | 15 | Using where | | 1 | SIMPLE | c | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_company_id | 1 | Using where | +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ This query takes 2 minutes ~20 seconds to execute. The query that is ACTUALLY being run on the server is this one: SELECT COUNT(*) AS num_results FROM (SELECT f.form_question_has_answer_id FROM form_question_has_answer f INNER JOIN project_company_has_user p ON f.form_question_has_answer_user_id = p.project_company_has_user_user_id INNER JOIN company c ON p.project_company_has_user_company_id = c.company_id INNER JOIN project p2 ON p.project_company_has_user_project_id = p2.project_id INNER JOIN user u ON p.project_company_has_user_user_id = u.user_id INNER JOIN form f2 ON p.project_company_has_user_project_id = f2.form_project_id WHERE (f2.form_template_name = 'custom' AND p.project_company_has_user_garbage_collection = 0 AND p.project_company_has_user_project_id = '29') AND (LCASE(c.company_country) LIKE '%ge%' OR LCASE(c.company_country) LIKE '%abcde%') AND f.form_question_has_answer_form_id = '174' GROUP BY f.form_question_has_answer_id;) dctrn_count_query; With explain plans (again same on dev and production): +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ | id | select_type | table | type | possible_keys | key | key_len | ref | rows | Extra | +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ | 1 | PRIMARY | NULL | NULL | NULL | NULL | NULL | NULL | NULL | Select tables optimized away | | 2 | DERIVED | p2 | const | PRIMARY | PRIMARY | 4 | | 1 | Using index | | 2 | DERIVED | f | ref | form_question_has_answer_form_id,form_question_has_answer_user_id | form_question_has_answer_form_id | 4 | | 797 | Using where | | 2 | DERIVED | p | ref | project_company_has_user_unique_key,project_company_has_user_user_id,project_company_has_user_company_id,project_company_has_user_project_id,project_company_has_user_garbage_collection | project_company_has_user_user_id | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using where | | 2 | DERIVED | f2 | ref | form_project_id | form_project_id | 4 | | 15 | Using where | | 2 | DERIVED | c | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_company_id | 1 | Using where | | 2 | DERIVED | u | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_user_id | 1 | Using where; Using index | +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ On the production server the information I have is as follows. Upon execution: +-------------+ | num_results | +-------------+ | 3 | +-------------+ 1 row in set (2 min 14.28 sec) Show profile: +--------------------------------+------------+ | Status | Duration | +--------------------------------+------------+ | starting | 0.000016 | | checking query cache for query | 0.000057 | | Opening tables | 0.004388 | | System lock | 0.000003 | | Table lock | 0.000036 | | init | 0.000030 | | optimizing | 0.000016 | | statistics | 0.000111 | | preparing | 0.000022 | | executing | 0.000004 | | Sorting result | 0.000002 | | Sending data | 136.213836 | | end | 0.000007 | | query end | 0.000002 | | freeing items | 0.004273 | | storing result in query cache | 0.000010 | | logging slow query | 0.000001 | | logging slow query | 0.000002 | | cleaning up | 0.000002 | +--------------------------------+------------+ On development the results are as follows. +-------------+ | num_results | +-------------+ | 3 | +-------------+ 1 row in set (0.08 sec) Again the profile for this query: +--------------------------------+----------+ | Status | Duration | +--------------------------------+----------+ | starting | 0.000022 | | checking query cache for query | 0.000148 | | Opening tables | 0.000025 | | System lock | 0.000008 | | Table lock | 0.000101 | | optimizing | 0.000035 | | statistics | 0.001019 | | preparing | 0.000047 | | executing | 0.000008 | | Sorting result | 0.000005 | | Sending data | 0.086565 | | init | 0.000015 | | optimizing | 0.000006 | | executing | 0.000020 | | end | 0.000004 | | query end | 0.000004 | | freeing items | 0.000028 | | storing result in query cache | 0.000005 | | removing tmp table | 0.000008 | | closing tables | 0.000008 | | logging slow query | 0.000002 | | cleaning up | 0.000005 | +--------------------------------+----------+ If i remove user and/or project innerjoins the query is reduced to 30s. Last bit of information I have: Mysqlserver and Apache are on the same box, there is only one box for production. Production output from top: before & after. top - 15:43:25 up 78 days, 12:11, 4 users, load average: 1.42, 0.99, 0.78 Tasks: 162 total, 2 running, 160 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 50.4%sy, 0.0%ni, 49.5%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3772580k used, 265288k free, 243704k buffers Swap: 3905528k total, 265384k used, 3640144k free, 1207944k cached top - 15:44:31 up 78 days, 12:13, 4 users, load average: 1.94, 1.23, 0.87 Tasks: 160 total, 2 running, 157 sleeping, 0 stopped, 1 zombie Cpu(s): 0.2%us, 50.6%sy, 0.0%ni, 49.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3834300k used, 203568k free, 243736k buffers Swap: 3905528k total, 265384k used, 3640144k free, 1207804k cached But this isn't a good representation of production's normal status so here is a grab of it from today outside of executing the queries. top - 11:04:58 up 79 days, 7:33, 4 users, load average: 0.39, 0.58, 0.76 Tasks: 156 total, 1 running, 155 sleeping, 0 stopped, 0 zombie Cpu(s): 3.3%us, 2.8%sy, 0.0%ni, 93.9%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3676136k used, 361732k free, 271480k buffers Swap: 3905528k total, 268736k used, 3636792k free, 1063432k cached Development: This one doesn't change during or after. top - 15:47:07 up 110 days, 22:11, 7 users, load average: 0.17, 0.07, 0.06 Tasks: 210 total, 2 running, 208 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4111972k total, 1821100k used, 2290872k free, 238860k buffers Swap: 4183036k total, 66472k used, 4116564k free, 921072k cached

  Read the article

• DataContractSerializer and deserializing web service response types

  - by matra

  Hi, I am using calling web services and using WCF generated service-reference on the client. I have saved XML responses that are received from test service to disk (without SOAP envelope and body tags) I would like to load them from disk and create objects from them. Lets' take the following method from my web service: SomeMethodResponse SomeMethod(SomeMethodRequest req) I manually (through SOAP UI) save the response to disk to file, Sample response: < SomeMethodResponse xmlns="http://myNamespace"> <SomeMember1>value</SomeMember1> </SomeMethodResponse xmlns="http://myNamespace"> Then I try to deserialize the object from file using: DataContractSerializer dcs = new DataContractSerializer(typeof(SomeMethodResponse)) This fails – the serializer complains with the error, that it is expecting element in namespace 'http://schemas.datacontract.org/2004/07', but found element in 'http://myNamespace'. Question: Why does the DataContractSerializer not use the namespace, that is declared on SomeMethodResponseType with XmlTypeAttribute(Namespace="http://myNamespace")? I can work around this by explicitly providing the namespace and the root element to DataContractSerializer constructor. But then it fails with message similar to: Error in line X position Y (last line of the XMLdocument). 'EndElement' 'SomeMethodResponse from namespace 'httpmyNapespace’ is not expected. Expecting element 'someNameField'. SomeName is an element in the XSD that web service is using. It is also a property on the SomeMethodResponse type, backed by the private field called someNameField. It looks like DataContractSerializer is trying to deserialize the fields in addition to properties. How can I deserailize XML that I have saved from disk and get back the object of same type that SomeMethod is returning? Thanks, Matra

  Read the article

• Hive Based Registry in Flash

  - by Psychic

  To start with I'll say I've read the post here and I'm still having trouble. I'm trying to create a CE6 image with a hive-based registry that actually stores results through a reboot. I've ticked the hive settings in the catalog items. In common.reg, I've set the location of the hive ([HKEY_LOCAL_MACHINE\init\BootVars] "SystemHive") to "Hard Drive\Registry" (Note: the flash shows up as a device called "Hard Drive") In common.reg, I've set "Flags"=dword:3 in the same place to get the device manager loaded along with the storage manager I've verified that these settings are wrapped in "; HIVE BOOT SECTION" This is where it starts to fall over. It all compiles fine, but on the target system, when it boots, I get: A directory, called "Hard Disk" where a registry is put A device, name called "Hard Disk2" where the permanent flash is Any changes made to the registry are lost on a reboot What am I still missing? Why is the registry not being stored on the flash? Strangly, if I create a random file/directory in the registry directory, it is still there after a reboot, so even though this directory isn't on the other partition (where I tried to put it), it does appear to be permanent. If it is permanent, why don't registry settings save (ie Ethernet adapter IP addresses?) I'm not using any specific profiles, so I'm at a loss as to what the last step is to make this hive registry a permanent store.

  Read the article

• Visual studio 2010 setup project problem.

  - by Guru

  Hi there, I've made an application that uses .NET framework 3.5 SP1 and SQL Server 2008 Express. Application is fine and now i'm going to to make a setup project for this. When I first build my setup it was fine as all the prerequisites were not included in setup. But I want my setup to install .NET 3.5 SP1 and SQL SERVER 2008 Express also. So for this I've changed the options in setup project's properties from "Download prerequisites from following location" to "Download prerequisites from the same location as my application". In addition to that I've also checked the options above like .NET 3.5 SP1 and SQL Server 2008 Express etc. After doing all this I build my project again. This time I'm Getting 57 Errors. Error 1 The install location for prerequisites has not been set to 'component vendor's web site' and the file 'DotNetFX35SP1\dotNetFX20\aspnet.msp' in item '.NET Framework 3.5 SP1' can not be located on disk. See Help for more information. D:\MindStrike Setup\MindStrike Setup.vdproj MindStrike Setup Error 2 The install location for prerequisites has not been set to 'component vendor's web site' and the file 'DotNetFX35SP1\dotNetFX20\aspnet_64.msp' in item '.NET Framework 3.5 SP1' can not be located on disk. See Help for more information. D:\MindStrike Setup\MindStrike Setup.vdproj MindStrike Setup Error 3 The install location for prerequisites has not been set to 'component vendor's web site' and the file 'DotNetFX35SP1\dotNetFX20\clr.msp' in item '.NET Framework 3.5 SP1' can not be located on disk. See Help for more information. D:\MindStrike Setup\MindStrike Setup.vdproj MindStrike Setup Error 4 The install location for prerequisites has not been set to 'component vendor's web site' and the file 'DotNetFX35SP1\dotNetFX20\clr_64.msp' in item '.NET Framework 3.5 SP1' can not be located on disk. See Help for more information. D:\MindStrike Setup\MindStrike Setup.vdproj MindStrike Setup As the question will become too large so I'm just pasting 3 errors but there are totally 57 errors. Please help me . Thanks in advance Guru

  Read the article

• Out of Core Implementation of a Quadtree

  - by Nima

  Hi, I am trying to build a Quadtree data structure(or let's just say a tree) on the secondary memory(Hard Disk). I have a C++ program to do so and I use fopen to create the files. Also, I am using tesseral coding to store each cell in a file named with its corresponding code to store it on the disk in one directory. The problem is that after creating about 1,100 files, fopen just returns NULL and stops creating new files. I can create further files manually in that directory, but using C++ it can not create any further files. I know about max limit of inode on ext3 filesystem which is (from Wikipedia) 32,000 but mine is way less than that, also note that I can create files manually on the disk; just not through fopen. Also, I really appreciate any idea regarding the best way to store a very dynamic quadtree on disk(I need the nodes to be in separate files and the quadtree might have a depth of 50). Using nested directories is one idea, but I think it will slow down the performance because of following the links on the filesystem to access the file. Thanks, Nima

  Read the article

• Problem using custom HttpHandler to process requests for both .aspx and non-extension pages in IIS7

  - by Noel

  I am trying to process both ".aspx" and non-extension page requests (i.e. both contact.aspx and /contact/) using a custom HttpHandler in IIS7. My handler works just fine in either one case or the other, but as soon as I try to process both cases, it only works for one. Please see Handlers snippet from my web.config below: If i keep only mapping to "*.aspx" then all .aspx requests are processed correctly, but obviously extensionless requests won't work: <add name="AllPages.ASPX" path="*.aspx" verb="*" type="Test.PageHandlerFactory, Test" preCondition="" /> If i change the mapping to "*" then all extensionless requests are processed correctly, but ".aspx" requests that should still be handled by this handler stop working. Note that i added the StaticFiles entry in order to process files that are on disk like images, css, js, etc. <add name="WebResource" path="WebResource.axd" verb="GET" type="System.Web.Handlers.AssemblyResourceLoader" /> <add name="StaticFiles" verb="GET,HEAD" path="*.*" type="System.Web.StaticFileHandler" resourceType="File" /> <add name="AllPages" path="*" verb="*" type="Test.PageHandlerFactory, Test" preCondition="" /> The crazy thing is that when i load an ".aspx" request (with the 2nd configuration shown) IIS7 gives a 404 not found error. The error also says that the request is processed by the StaticFiles handler. But I made sure to add resourceType="File" to the StaticFileHandler in order to avoid this. According to MS this means the request is only for "physical files on disk". Am i misreading/interpreting the "on disk" part? My .aspx file isn't on disk, that's why i want to use the handler in the first place.

  Read the article

• SQL Server Clustered Index: (Physical) Data Page Order

  - by scherand

  I am struggling understanding what a clustered index in SQL Server 2005 is. I read the MSDN article Clustered Index Structures (among other things) but I am still unsure if I understand it correctly. The (main) question is: what happens if I insert a row (with a "low" key) into a table with a clustered index? The above mentioned MSDN article states: The pages in the data chain and the rows in them are ordered on the value of the clustered index key. And Using Clustered Indexes for example states: For example, if a record is added to the table that is close to the beginning of the sequentially ordered list, any records in the table after that record will need to shift to allow the record to be inserted. Does this mean that if I insert a row with a very "low" key into a table that already contains a gazillion rows literally all rows are physically shifted on disk? I cannot believe that. This would take ages, no? Or is it rather (as I suspect) that there are two scenarios depending on how "full" the first data page is. A) If the page has enough free space to accommodate the record it is placed into the existing data page and data might be (physically) reordered within that page. B) If the page does not have enough free space for the record a new data page would be created (anywhere on the disk!) and "linked" to the front of the leaf level of the B-Tree? This would then mean the "physical order" of the data is restricted to the "page level" (i.e. within a data page) but not to the pages residing on consecutive blocks on the physical hard drive. The data pages are then just linked together in the correct order. Or formulated in an alternative way: if SQL Server needs to read the first N rows of a table that has a clustered index it can read data pages sequentially (following the links) but these pages are not (necessarily) block wise in sequence on disk (so the disk head has to move "randomly"). How close am I? :)

  Read the article

• loaded resources looks ugly

  - by Xaver

  I have the TreeView class using in my project. I use icons for it.First i load icons so: ImageList^ il = gcnew ImageList(); il->Images->Add(Image::FromFile("DISK.ico")); il->Images->Add(Image::FromFile("FILE.ico")); il->Images->Add(Image::FromFile("FOLDER.ico")); treeView1->ImageList = il; All was good. But i dont like that if i delete my icons from directory of project. there is error in my project. I decide to add icons in .resx file. Now icons loading look so: ImageList^ il = gcnew ImageList(); Resources::ResourceManager^ resourceManager = gcnew Resources::ResourceManager ("FilesSaver.Form1", GetType()->Assembly); Object^ disk = resourceManager->GetObject("DISK"); il->Images->Add(reinterpret_cast<Image^>(disk)); Object^ file = resourceManager->GetObject("FILE"); il->Images->Add(reinterpret_cast<Image^>(file)); Object^ folder = resourceManager->GetObject("FOLDER"); il->Images->Add(reinterpret_cast<Image^>(folder)); treeView1->ImageList = il; And why icons in the TreeView looks ugly (they look lighter and have a big black border). Why did this happen?

  Read the article

• Fastest PNG decoder for .NET

  - by sboisse

  Our web server needs to process many compositions of large images together before sending the results to web clients. This process is performance critical because the server can receive several thousands of requests per hour. Right now our solution loads PNG files (around 1MB each) from the HD and sends them to the video card so the composition is done on the GPU. We first tried loading our images using the PNG decoder exposed by the XNA API. We saw the performance was not too good. To understand if the problem was loading from the HD or the decoding of the PNG, we modified that by loading the file in a memory stream, and then sending that memory stream to the .NET PNG decoder. The difference of performance using XNA or using System.Windows.Media.Imaging.PngBitmapDecoder class is not significant. We roughly get the same levels of performance. Our benchmarks show the following performance results: Load images from disk: 37.76ms 1% Decode PNGs: 2816.97ms 77% Load images on Video Hardware: 196.67ms 5% Composition: 87.80ms 2% Get composition result from Video Hardware: 166.21ms 5% Encode to PNG: 318.13ms 9% Store to disk: 3.96ms 0% Clean up: 53.00ms 1% Total: 3680.50ms 100% From these results we see that the slowest parts are when decoding the PNG. So we are wondering if there wouldn't be a PNG decoder we could use that would allow us to reduce the PNG decoding time. We also considered keeping the images uncompressed on the hard disk, but then each image would be 10MB in size instead of 1MB and since there are several tens of thousands of these images stored on the hard disk, it is not possible to store them all without compression.

  Read the article

• Simulating O_NOFOLLOW (2): Is this other approach safe?

  - by Daniel Trebbien

  As a follow-up question to this one, I thought of another approach which builds off of @caf's answer for the case where I want to append to file name and create it if it does not exist. Here is what I came up with: Create a temporary directory with mode 0700 in a system temporary directory on the same filesystem as file name. Create an empty, temporary, regular file (temp_name) in the temporary directory (only serves as placeholder). Open file name for reading only, just to create it if it does not exist. The OS may follow name if it is a symbolic link; I don't care at this point. Make a hard link to name at temp_name (overwriting the placeholder file). If the link call fails, then exit. (Maybe someone has come along and removed the file at name, who knows?) Use lstat on temp_name (now a hard link). If S_ISLNK(lst.st_mode), then exit. open temp_name for writing, append (O_WRONLY | O_APPEND). Write everything out. Close the file descriptor. unlink the hard link. Remove the temporary directory. (All of this, by the way, is for an open source project that I am working on. You can view the source of my implementation of this approach here.) Is this procedure safe against symbolic link attacks? For example, is it possible for a malicious process to ensure that the inode for name represents a regular file for the duration of the lstat check, then make the inode a symbolic link with the temp_name hard link now pointing to the new, symbolic link? I am assuming that a malicious process cannot affect temp_name.

  Read the article

• TFS Folders - Getting them to work like Subversion "Trunk/Tags/Branches"

  - by Sam Schutte

  I recently started using Team Foundation Server, and am having some trouble getting it to work the way I want it to. I've used Subversion for a couple years now, and love the way it works. I always set up three folders under each project, Trunk, Tags, and Branches. When I'm working on a project, all my code lives under a folder called "C:\dev\projectname". This "projectname" folder can be made to point to either trunk, or any of the branches or tags using Subversion (with the switch command). Now that I'm using TFS (my client's system), I'd like things to work the same way. I created a "Trunk" folder with my project in it, and mapped "Project/Trunk/Website" to "c:\dev\Website". Now, I want to make a release under the "tags" folder (located in "Project/Tags/Version 1.0/Website", and TFS is giving me the following error when I execute the branch command: "No appropriate mapping exists for $Project/tags/Version 1.0/Website" From what I can find on the internet, TFS expects you to have a mapping to your hard drive at the root of the project (the "Project" folder in my case), and then have all the source code that lives in trunk, tags and branches all pulled down to your hard drive. This sucks because it requires way too much stuff on your hard drive, and even worse, when you are working in a solution in Visual Studio, you won't be able to pull down "Version 2.0" and have all your project references to other projects work, because they'll all be pointing to "trunk" folders under the main folder, not just the main folder itself. What I want to do is have the root "Project/Website" folder on my hard drive, and be able to have it point to (mapped to) either tags, branches, or trunk, depending on what i'm doing, without having to screw around with fixing Visual Studio project references. Ideas?

  Read the article

• Why this code generates different numbers?

  - by frbry

  Hello, I have this function that creates a unique number for hard-disk and CPU combination. DWORD hw_hash() { char drv[4]; char szNameBuffer[256]; DWORD dwHddUnique; DWORD dwProcessorUnique; DWORD dwUniqueKey; char *sysDrive = getenv ("SystemDrive"); strcpy(drv, sysDrive); drv[2] = '\\'; drv[3] = 0; GetVolumeInformation(drv, szNameBuffer, 256, &dwHddUnique, NULL, NULL, NULL, NULL); SYSTEM_INFO si; GetSystemInfo(&si); dwProcessorUnique = si.dwProcessorType + si.wProcessorArchitecture + si.wProcessorRevision; dwUniqueKey = dwProcessorUnique + dwHddUnique; return dwUniqueKey; } It returns different numbers if I format my hard-disk and install a new Windows. Any ideas, why? Thank you. Edit: OK, Got it: This function returns the volume serial number that the operating system assigns when a hard disk is formatted. To programmatically obtain the hard disk's serial number that the manufacturer assigns, use the Windows Management Instrumentation (WMI) Win32_PhysicalMedia property SerialNumber. I should do more research before posting my problems online. Sorry to bother you, let's keep this here in case anybody else can need it.

  Read the article

• IIS Flash Remoting Request Limit introduced with Coldfusion 9

  - by ciaranarcher

  Hi all We've just been our Coldfusion servers from Enterprise CF 8.01 to CF 9. They are running Win 2008. We ran into trouble on those servers that provide the Flash remoting back-end for a Flex application we provide. Once the CF 9 upgrade was complete we noticed that during busy times when many Flex clients were connecting, we appeared to have a hard limit of 25 Flash Remoting Requests running, despite having much higher limits (in fact 150) set in CF Admin. Initially we thought that this was an issue with the fact that Blaze DS was now bundled with CF 9 (rather than a separate install) so we decided to roll-back the CF 9 installation. This, unfortunately, didn't work and we were still stuck with out hard limit of 25 Flash Remoting requests. Then looking at IIS we noticed that the CF9 ISAPI filter was still installed (after we had ran the Web Service Configuration part of the install). That was removed and the CF 8 one was re-run and all of a sudden the Flash Remoting hard limit disappeared. So it seems that it might have had something to do with the wsconfig of CF 9 (C:\ColdFusion9\runtime\bin\wsconfig.exe) Has anyone else had this problem, or does anybody know of where these hard limits are configured in IIS? Any and all help appreciated!

  Read the article

• Is there a reason why SSIS significantly slows down after a few minutes?

  - by Mark

  I'm running a fairly substantial SSIS package against SQL 2008 - and I'm getting the same results both in my dev environment (Win7-x64 + SQL-x64-Developer) and the production environment (Server 2008 x64 + SQL Std x64). The symptom is that initial data loading screams at between 50K - 500K records per second, but after a few minutes the speed drops off dramatically and eventually crawls embarrasingly slowly. The database is in Simple recovery model, the target tables are empty, and all of the prerequisites for minimally logged bulk inserts are being met. The data flow is a simple load from a RAW input file to a schema-matched table (i.e. no complex transforms of data, no sorting, no lookups, no SCDs, etc.) The problem has the following qualities and resiliences: Problem persists no matter what the target table is. RAM usage is lowish (45%) - there's plenty of spare RAM available for SSIS buffers or SQL Server to use. Perfmon shows buffers are not spooling, disk response times are normal, disk availability is high. CPU usage is low (hovers around 25% shared between sqlserver.exe and DtsDebugHost.exe) Disk activity primarily on TempDB.mdf, but I/O is very low (< 600 Kb/s) OLE DB destination and SQL Server Destination both exhibit this problem. To sum it up, I expect either disk, CPU or RAM to be exhausted before the package slows down, but instead its as if the SSIS package is taking an afternoon nap. SQL server remains responsive to other queries, and I can't find any performance counters or logged events that betray the cause of the problem. I'll gratefully reward any reasonable answers / suggestions.

  Read the article

• Find existence of number in a sorted list in constant time? (Interview question)

  - by Rich

  I'm studying for upcoming interviews and have encountered this question several times (written verbatim) Find or determine non existence of a number in a sorted list of N numbers where the numbers range over M, M N and N large enough to span multiple disks. Algorithm to beat O(log n); bonus points for constant time algorithm. First of all, I'm not sure if this is a question with a real solution. My colleagues and I have mused over this problem for weeks and it seems ill formed (of course, just because we can't think of a solution doesn't mean there isn't one). A few questions I would have asked the interviewer are: Are there repeats in the sorted list? What's the relationship to the number of disks and N? One approach I considered was to binary search the min/max of each disk to determine the disk that should hold that number, if it exists, then binary search on the disk itself. Of course this is only an order of magnitude speedup if the number of disks is large and you also have a sorted list of disks. I think this would yield some sort of O(log log n) time. As for the M N hint, perhaps if you know how many numbers are on a disk and what the range is, you could use the pigeonhole principle to rule out some cases some of the time, but I can't figure out an order of magnitude improvement. Also, "bonus points for constant time algorithm" makes me a bit suspicious. Any thoughts, solutions, or relevant history of this problem?

  Read the article

• Week in Geek: LastPass Rescues Xmarks Edition

  - by Asian Angel

  This week we learned how to breathe new life into an aging Windows Mobile 6.x device, use filters in Photoshop, backup and move VirtualBox machines, use the BitDefender Rescue CD to clean an infected PC, and had fun setting up a pirates theme on our computers. Photo by _nash. Weekly Feature Do you love using the Faenza icon set on your Ubuntu system but feel that there are a few much needed icons missing (or you desire a different version of a particular icon)? Then you may want to take a look at the Faenza Variants icon pack. The icons are available in the following sizes: 16px, 22px, 32px, 48px and scalable sizes. Photo by Asian Angel. Faenza Variants Random Geek Links Another week with extra link goodness to help keep you on top of the news. Photo by Asian Angel. LastPass acquires Xmarks, premium service announced Xmarks announced that it has been acquired by LastPass, a cross-platform password management service. This also means that Xmarks is now in transition from a “free” to a “freemium” business model. WikiLeaks reappears on European Net domains WikiLeaks has re-emerged on a Swiss Internet domain followed by domains in Germany, Finland, and the Netherlands, sidestepping a move that had in effect taken the controversial site off the Internet. Iran: Yes, Stuxnet hurt our nuclear program The Stuxnet worm got some big play from Iranian President Mahmoud Ahmadinejad, who acknowledged that the malware dinged his nuclear program. More Windows Rogues than Just AV – Fake Defragmenter Check Disk Don’t think for a second that rogues are limited to scareware, because as so-called products such as “System Defragmenter”, “Scan Disk” “Check Disk” prove, they’re not. Internet Explorer’s Protected Mode can be bypassed Researchers from Verizon Business have now described a way of bypassing Protected Mode in IE 7 and 8 in order to gain access to user accounts. Can you really see who viewed your Facebook profile? Rogue application spreads virally Once again, a rogue application is spreading virally between Facebook users pretending to offer you a way of seeing who has viewed your profile. More holes in Palm’s WebOS Researchers Orlando Barrera and Daniel Herrera, who both work for security firm SecTheory, have discovered a gaping security hole in Palm’s WebOS smartphone operating system. Next-gen banking Trojans hit APAC With the proliferation of banking Trojans, Web and smartphone users of online banking services have to be on constant alert to avoid falling prey to fraud schemes, warned Etay Maor, project manager for RSA Fraud Action. AVG update cripples 64-bit computers A signature update automatically deployed by the AVG virus scanner Thursday has crippled numerous computers. Article includes link to forums to fix computers affected after a restart. Congress moves to outlaw ‘mystery charges’ for Web shoppers Legislation that makes it illegal for Web merchants and so-called post-transaction marketers to charge credit cards without the card owners’ say-so came closer to becoming law this week. Ballmer Set to “Look Into” Windows Home Server Drive Extender Fiasco Tuesday’s announcement from Microsoft regarding the removal of Drive Extender from Windows Home Server has sent shock waves across the web. Google tweaks search recipe to ding scam artists Google has changed its search algorithm to penalize sites deemed to provide an “extremely poor user experience” following a New York Times story on a merchant who justified abusive behavior towards customers as a search-engine optimization tactic. Geek Video of the Week Watch as our two friends debate back and forth about the early adoption of new technology through multiple time periods (Stone Age to the far future). Will our reluctant friend finally succumb to the temptation? Photo by CollegeHumor. Early Adopters Through History Random TinyHacker Links Fix Issues in Windows 7 Using Reliability Monitor Learn how to analyze Windows 7 errors and then fix them using the built-in reliability monitor. Learn About IE Tab Groups Tab groups is a useful feature in IE 8. Here’s a detailed guide to what it is all about. Google’s Book Helps You Learn About Browsers and Web A cool new online book by the Google Chrome team on browsers and the web. TrustPort Internet Security 2011 – Good Security from a Less Known Provider TrustPort is not exactly a well-known provider of security solutions. At least not in the consumer space. This review tests in detail their latest offering. How the World is Using Cell phones An infographic showing the shocking demographics of cell phone use. Super User Questions See the great answers to these questions from Super User. I am unable to access my C drive. It says it is unable to display current owner. List of Windows special directories/shortcuts like ‘%TEMP%’ Is using multiple passes for wiping a disk really necessary? How can I view two files side by side in Notepad++ Is there any tool that automatically puts screenshots to my Dropbox? How-To Geek Weekly Article Recap Look through our hottest articles from this past week at How-To Geek. How to Create a Software RAID Array in Windows 7 9 Alternatives for Windows Home Server’s Drive Extender Why Doesn’t Disk Cleanup Delete Everything from the Temp Folder? Ask the Readers: How Much Do You Customize Your Operating System? How to Upload Really Large Files to SkyDrive, Dropbox, or Email One Year Ago on How-To Geek Enjoy reading through these awesome articles from one year ago. How To Upgrade from Vista to Windows 7 Home Premium Edition How To Fix No Aero Transparency in Windows 7 Troubleshoot Startup Problems with Startup Repair Tool in Windows 7 & Vista Rename the Guest Account in Windows 7 for Enhanced Security Disable Error Reporting in XP, Vista, and Windows 7 The Geek Note That wraps things up here for this week. Regardless of the weather wherever you may be, we hope that you have an opportunity to get outside and have some fun! Remember to keep sending those great tips in to us at [email protected]. Photo by Tony the Misfit. Latest Features How-To Geek ETC The How-To Geek Guide to Learning Photoshop, Part 8: Filters Get the Complete Android Guide eBook for Only 99 Cents [Update: Expired] Improve Digital Photography by Calibrating Your Monitor The How-To Geek Guide to Learning Photoshop, Part 7: Design and Typography How to Choose What to Back Up on Your Linux Home Server How To Harmonize Your Dual-Boot Setup for Windows and Ubuntu Hang in There Scrat! – Ice Age Wallpaper How Do You Know When You’ve Passed Geek and Headed to Nerd? On The Tip – A Lamborghini Theme for Chrome and Iron What if Wile E. Coyote and the Road Runner were Human? [Video] Peaceful Winter Cabin Wallpaper Store Tabs for Later Viewing in Opera with Tab Vault

  Read the article

• Week in Geek: US Govt E-card Scam Siphons Confidential Data Edition

  - by Asian Angel

  This week we learned how to “back up photos to Flickr, automate repetitive tasks, & normalize MP3 volume”, enable “stereo mix” in Windows 7 to record audio, create custom papercraft toys, read up on three alternatives to Apple’s flaky iOS alarm clock, decorated our desktops & app docks with Google icon packs, and more. Photo by alexschlegel. Random Geek Links It has been a busy week on the security & malware fronts and we have a roundup of the latest news to help keep you updated. Photo by TopTechWriter.US. US govt e-card scam hits confidential data A fake U.S. government Christmas e-card has managed to siphon off gigabytes of sensitive data from a number of law enforcement and military staff who work on cybersecurity matters, many of whom are involved in computer crime investigations. Security tool uncovers multiple bugs in every browser Michal Zalewski reports that he discovered the vulnerability in Internet Explorer a while ago using his cross_fuzz fuzzing tool and reported it to Microsoft in July 2010. Zalewski also used cross_fuzz to discover bugs in other browsers, which he also reported to the relevant organisations. Microsoft to fix Windows holes, but not ones in IE Microsoft said that it will release two security bulletins next week fixing three holes in Windows, but it is still investigating or working on fixing holes in Internet Explorer that have been reportedly exploited in attacks. Microsoft warns of Windows flaw affecting image rendering Microsoft has warned of a Windows vulnerability that could allow an attacker to take control of a computer if the user is logged on with administrative rights. Windows 7 Not Affected by Critical 0-Day in the Windows Graphics Rendering Engine While confirming that details on a Critical zero-day vulnerability have made their way into the wild, Microsoft noted that customers running the latest iteration of Windows client and server platforms are not exposed to any risks. Microsoft warns of Office-related malware Microsoft’s Malware Protection Center issued a warning this week that it has spotted malicious code on the Internet that can take advantage of a flaw in Word and infect computers after a user does nothing more than read an e-mail. *Refers to a flaw that was addressed in the November security patch releases. Make sure you have all of the latest security updates installed. Unpatched hole in ImgBurn disk burning application According to security specialist Secunia, a highly critical vulnerability in ImgBurn, a lightweight disk burning application, can be used to remotely compromise a user’s system. Hole in VLC Media Player Virtual Security Research (VSR) has identified a vulnerability in VLC Media Player. In versions up to and including 1.1.5 of the VLC Media Player. Flash Player sandbox can be bypassed Flash applications run locally can read local files and send them to an online server – something which the sandbox is supposed to prevent. Chinese auction site touts hacked iTunes accounts Tens of thousands of reportedly hacked iTunes accounts have been found on Chinese auction site Taobao, but the company claims it is unable to take action unless there are direct complaints. What happened in the recent Hotmail outage Mike Schackwitz explains the cause of the recent Hotmail outage. DOJ sends order to Twitter for Wikileaks-related account info The U.S. Justice Department has obtained a court order directing Twitter to turn over information about the accounts of activists with ties to Wikileaks, including an Icelandic politician, a legendary Dutch hacker, and a U.S. computer programmer. Google gets court to block Microsoft Interior Department e-mail win The U.S. Federal Claims Court has temporarily blocked Microsoft from proceeding with the $49.3 million, five-year DOI contract that it won this past November. Google Apps customers get email lockdown Companies and organisations using Google Apps are now able to restrict the email access of selected users. LibreOffice Is the Default Office Suite for Ubuntu 11.04 Matthias Klose has announced some details regarding the replacement of the old OpenOffice.org 3.2.1 packages with the new LibreOffice 3.3 ones, starting with the upcoming Ubuntu 11.04 (Natty Narwhal) Alpha 2 release. Sysadmin Geek Tips Photo by Filomena Scalise. How to Setup Software RAID for a Simple File Server on Ubuntu Do you need a file server that is cheap and easy to setup, “rock solid” reliable, and has Email Alerting? This tutorial shows you how to use Ubuntu, software RAID, and SaMBa to accomplish just that. How to Control the Order of Startup Programs in Windows While you can specify the applications you want to launch when Windows starts, the ability to control the order in which they start is not available. However, there are a couple of ways you can easily overcome this limitation and control the startup order of applications. Random TinyHacker Links Using Opera Unite to Send Large Files A tutorial on using Opera Unite to easily send huge files from your computer. WorkFlowy is a Useful To-do List Tool A cool to-do list tool that lets you integrate multiple tasks in one single list easily. Playing Flash Videos on iOS Devices Yes, you can play flash videos on jailbroken iPhones. Here’s a tutorial. Clear Safari History and Cookies On iPhone A tutorial on clearing your browser history on iPhone and other iOS devices. Monitor Your Internet Usage Here’s a cool, cross-platform tool to monitor your internet bandwidth. Super User Questions See what the community had to say on these popular questions from Super User this week. Why is my upload speed much less than my download speed? Where should I find drivers for my laptop if it didn’t come with a driver disk? OEM Office 2010 without media – how to reinstall? Is there a point to using theft tracking software like Prey on my laptop, if you have login security? Moving an “all-in-one” PC when turned on/off How-To Geek Weekly Article Recap Get caught up on your HTG reading with our hottest articles from this past week. How to Combine Rescue Disks to Create the Ultimate Windows Repair Disk How To Boot 10 Different Live CDs From 1 USB Flash Drive What is Camera Raw, and Why Would a Professional Prefer it to JPG? Did You Know Facebook Has Built-In Shortcut Keys? The How-To Geek Guide to Audio Editing: The Basics One Year Ago on How-To Geek Enjoy looking through our latest gathering of retro article goodness. Learning Windows 7: Create a Homegroup & Join a New Computer To It How To Disconnect a Machine from a Homegroup Use Remote Desktop To Access Other Computers On a Small Office or Home Network How To Share Files and Printers Between Windows 7 and Vista Allow Users To Run Only Specified Programs in Windows 7 The Geek Note That is all we have for you this week and we hope your first week back at work or school has gone very well now that the holidays are over. Know a great tip? Send it in to us at [email protected]. Photo by Pamela Machado. Latest Features How-To Geek ETC HTG Projects: How to Create Your Own Custom Papercraft Toy How to Combine Rescue Disks to Create the Ultimate Windows Repair Disk What is Camera Raw, and Why Would a Professional Prefer it to JPG? The How-To Geek Guide to Audio Editing: The Basics How To Boot 10 Different Live CDs From 1 USB Flash Drive The 20 Best How-To Geek Linux Articles of 2010 Arctic Theme for Windows 7 Gives Your Desktop an Icy Touch Install LibreOffice via PPA and Receive Auto-Updates in Ubuntu Creative Portraits Peek Inside the Guts of Modern Electronics Scenic Winter Lane Wallpaper to Create a Relaxing Mood Access Your Web Apps Directly Using the Context Menu in Chrome The Deep – Awesome Use of Metal Objects as Deep Sea Creatures [Video]

  Read the article

• Change or Reset Windows Password from a Ubuntu Live CD

  - by Trevor Bekolay

  If you can’t log in even after trying your twelve passwords, or you’ve inherited a computer complete with password-protected profiles, worry not – you don’t have to do a fresh install of Windows. We’ll show you how to change or reset your Windows password from a Ubuntu Live CD. This method works for all of the NT-based version of Windows – anything from Windows 2000 and later, basically. And yes, that includes Windows 7. You’ll need a Ubuntu 9.10 Live CD, or a bootable Ubuntu 9.10 Flash Drive. If you don’t have one, or have forgotten how to boot from the flash drive, check out our article on creating a bootable Ubuntu 9.10 flash drive. The program that lets us manipulate Windows passwords is called chntpw. The steps to install it are different in 32-bit and 64-bit versions of Ubuntu. Installation: 32-bit Open up Synaptic Package Manager by clicking on System at the top of the screen, expanding the Administration section, and clicking on Synaptic Package Manager. chntpw is found in the universe repository. Repositories are a way for Ubuntu to group software together so that users are able to choose if they want to use only completely open source software maintained by Ubuntu developers, or branch out and use software with different licenses and maintainers. To enable software from the universe repository, click on Settings > Repositories in the Synaptic window. Add a checkmark beside the box labeled “Community-maintained Open Source software (universe)” and then click close. When you change the repositories you are selecting software from, you have to reload the list of available software. In the main Synaptic window, click on the Reload button. The software lists will be downloaded. Once downloaded, Synaptic must rebuild its search index. The label over the text field by the Search button will read “Rebuilding search index.” When it reads “Quick search,” type chntpw in the text field. The package will show up in the list. Click on the checkbox near the chntpw name. Click on Mark for Installation. chntpw won’t actually be installed until you apply the changes you’ve made, so click on the Apply button in the Synaptic window now. You will be prompted to accept the changes. Click Apply. The changes should be applied quickly. When they’re done, click Close. chntpw is now installed! You can close Synaptic Package Manager. Skip to the section titled Using chntpw to reset your password. Installation: 64-bit The version of chntpw available in Ubuntu’s universe repository will not work properly on a 64-bit machine. Fortunately, a patched version exists in Debian’s Unstable branch, so let’s download it from there and install it manually. Open Firefox. Whether it’s your preferred browser or not, it’s very readily accessible in the Ubuntu Live CD environment, so it will be the easiest to use. There’s a shortcut to Firefox in the top panel. Navigate to http://packages.debian.org/sid/amd64/chntpw/download and download the latest version of chntpw for 64-bit machines. Note: In most cases it would be best to add the Debian Unstable branch to a package manager, but since the Live CD environment will revert to its original state once you reboot, it’ll be faster to just download the .deb file. Save the .deb file to the default location. You can close Firefox if desired. Open a terminal window by clicking on Applications at the top-left of the screen, expanding the Accessories folder, and clicking on Terminal. In the terminal window, enter the following text, hitting enter after each line: cd Downloadssudo dpkg –i chntpw* chntpw will now be installed. Using chntpw to reset your password Before running chntpw, you will have to mount the hard drive that contains your Windows installation. In most cases, Ubuntu 9.10 makes this simple. Click on Places at the top-left of the screen. If your Windows drive is easily identifiable – usually by its size – then left click on it. If it is not obvious, then click on Computer and check out each hard drive until you find the correct one. The correct hard drive will have the WINDOWS folder in it. When you find it, make a note of the drive’s label that appears in the menu bar of the file browser. If you don’t already have one open, start a terminal window by going to Applications > Accessories > Terminal. In the terminal window, enter the commands cd /medials pressing enter after each line. You should see one or more strings of text appear; one of those strings should correspond with the string that appeared in the title bar of the file browser earlier. Change to that directory by entering the command cd <hard drive label> Since the hard drive label will be very annoying to type in, you can use a shortcut by typing in the first few letters or numbers of the drive label (capitalization matters) and pressing the Tab key. It will automatically complete the rest of the string (if those first few letters or numbers are unique). We want to switch to a certain Windows directory. Enter the command: cd WINDOWS/system32/config/ Again, you can use tab-completion to speed up entering this command. To change or reset the administrator password, enter: sudo chntpw SAM SAM is the file that contains your Windows registry. You will see some text appear, including a list of all of the users on your system. At the bottom of the terminal window, you should see a prompt that begins with “User Edit Menu:” and offers four choices. We recommend that you clear the password to blank (you can always set a new password in Windows once you log in). To do this, enter “1” and then “y” to confirm. If you would like to change the password instead, enter “2”, then your desired password, and finally “y” to confirm. If you would like to reset or change the password of a user other than the administrator, enter: sudo chntpw –u <username> SAM From here, you can follow the same steps as before: enter “1” to reset the password to blank, or “2” to change it to a value you provide. And that’s it! Conclusion chntpw is a very useful utility provided for free by the open source community. It may make you think twice about how secure the Windows login system is, but knowing how to use chntpw can save your tail if your memory fails you two or eight times! Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDChange Your Forgotten Windows Password with the Linux System Rescue CDHow to Create and Use a Password Reset Disk in Windows Vista & Windows 7Reset Your Forgotten Password the Easy Way Using the Ultimate Boot CD for WindowsHow to install Spotify in Ubuntu 9.10 using Wine TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Add a Custom Title in IE using Spybot or Spyware Blaster When You Need to Hail a Taxi in NYC Live Map of Marine Traffic NoSquint Remembers Site Specific Zoom Levels (Firefox) New Firefox release 3.6.3 fixes 1 Critical bug Dark Side of the Moon (8-bit)

  Read the article

< Previous Page | 181 182 183 184 185 186 187 188 189 190 191 192  | Next Page >