Search Results

Search found 5716 results on 229 pages for 'dual channel'.

Page 194/229 | < Previous Page | 190 191 192 193 194 195 196 197 198 199 200 201  | Next Page >

  • Help with Ubuntu and Windows, separate HDs

    - by LuxuryMode
    Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

    Read the article

  • Any dangers in using DDR memory with a higher frequency than the FSB?

    - by raw_noob
    I'm looking to upgrade memory in an older motherboard. The processor is an AMD Sempron 2500+ with a maximum speed of 333/166MHz. The motherboard is an MSI MS-7061 (KV3M-V), which accepts up to 2Gb of DDR memory maximum PC2700 in 2 slots and has a maximum FSB of 333MHz. The board does not have dual-channel support. Existing memory includes a stick of 512Mb PC3200, which seems to be running OK (presumably at PC2700) but is rated 200MHz, which is below the FSB speed. The other stick is 256Mb PC2100/133MHz, again below the FSB speed. (All figures from CPU-Z.) I have a chance to acquire a single used stick of PC3200/400MHz memory very cheaply. Crucial's system scanner seems to suggest that this will be OK with my system, but other sites have suggested that running memory with a higher frequency than the FSB can cause instability. Is this true? Would I be better waiting until I can buy the correct PC2700/333MHz stick? I'm assuming that the mixed memory I have at present is running as 768Mb at 133MHz. Is this a reasonable assumption? If so, would you expect the performance differences between 768Mb/133MHz and 1Gb/333MHz to be very noticeable? If I install the new 1Gb/400 or 333MHz stick in slot 1, am I right in thinking that adding back the existing 512Mb/200MHz stick in slot 2 would pull the whole 1.5Gb system memory speed down to 200MHz? If so, which would be better - 1.5Gb/200MHz, or the single 1Gb stick at the full 333MHz that the FSB permits? Is more headroom more important than extra speed? Any help - or even opinions - gratefully received. I can't find reliable information, and I can't afford to make expensive mistakes.

    Read the article

  • Fedora installed in Legacy mode, how to make it work in UEFI?

    - by TryntaLearn
    I am trying to install a linux distribution on my new laptop. It's an MSI GE40 which comes preinstalled with windows 8. It's a UEFI machine. I have tried installing Ubuntu and Fedora with limited success. I've tried: running it in UEFI, UEFI with CSM mode, with secureboot enabled, ... with secureboot disabeled, ... with secureboot enabled but in user mode. I have had no success with any of these methods. With Ubuntu the grub loader shows up, but when I pick 'try ubuntu', or 'install ubuntu', it's just a blank screen(I've been using liveusb's btw). With Fedora, it'll show me the next screen on which it says 'binary authorised by vendor certificate' or 'Secure boot not enabled' and then stop doing anything. The closest thing to success I reached was switching to legacy mode to install Ubuntu, in which case I was able to get to the ubunutu installer but it wouldn't recognize windows 8 on my computer, so instead of continuing on I rebooted, and removed the USB pendrive to find my computer couldn't find windows 8. After a little dicking about I got it to find windows 8 again. Any ideas on how I should go about trying to install a distro on my computer? UPDATE:- So I ended up installing fedora using Legacy mode. To use both it and Windows at boot, I manually enter automatic repair so I can get to my UEFI settings and switch boot mode to UEFI to boot windows 8. I guess my question needs to be modified as to how do I get all of this to work in UEFI mode, so I can dual boot via selection through a bootloader, and not by repeatedly switching boot mode.

    Read the article

  • Privacy, VPN and routers

    - by user123189
    Ever since this ACTA push-up the things are starting to heat up around torrents and privacy. I am using Tribler now, but this is not secure enough for me. Not enough privacy. I've been using in the past a swedish VPN PPTP connection. What I observed is that, when the VPN connection was down, Internet traffic wasn't cut off, rather the downloads were continuing, this time with my real IP, wearing off my protection. 1st : How to enforce a VPN connection that will cut all traffic when down? That is, the moment the connection is down, all internet traffic should cease as if I'd pull the network plug out. 2nd: Is PPTP good enough or should I ask for SSTP or IKEV2 ? 3rd: Should I disable IPv6 ? Is VPN no longer private if I keep IPv6 active? I 'heard some stuff' about dual vpn routers to be able to improve privacy; but nothing more about how to configure one for such a task. 4th: Is there any kind of "black box" hardware equipment that can be used in hiding IP, encrypting traffic and so on ?

    Read the article

  • Xen Bridge only working when IP Assigned

    - by m.sr
    Hey! Just had an (in my sense) obscure situation. I have a Xen Server with bridged networking. Everything works fine since month. A while ago i configuresd a second bridge. only some DomUs get an channel on this bridge - my Dom0 doesn't need to / should'nt use this bridge. So just 5 minutes ago while rebooting the xen host (because of an other problem with the UPS) i decided to removed the fixed ip from the the interface of the Dom0 which belongs to the second bridge. So after reboot i noticed that none of the interfaces on the second bridge is available. I couldn't find a problem. Everything was just like before the reboot, except the interface of the Dom0 had no IP address. After a while i tried to give the DomO interface of this bridge an IP again and ... BOOM ... everything is up and running again! WTF? Why is it important to have the interface of a bridge configured in the Dom0? Even when confiugured 'wrong' (complitely different netowkr settings as the network really hanging on the bridge) everythjing works fine ... I don't get it. Could please someone explain? Tnaks a lot!

    Read the article

  • High speed network configuration

    - by Peter M
    Sorry if this seems to be a stupid question, I'm not sure how to specify what I want to know when checking google. I will have 2 or 3 devices pumping out data on a 100Base-T port. The combined data rate of all devices is about 15KB/S which exceeds the optimal 100Base-T channel capacity (12KB/S), but well within the realms of a 1000Base-T connection. Each device will be sending a burst of data in the form of an FTP transfer to a common, single host computer in a sequential manner ie: Device A establishes FTP connection and transfers data Device B establishes FTP connection and transfers data Device C establishes FTP connection and transfers data It may be that the A&B, B&C and C&A transfers overlap in the time domain to some extent. There will be minimal traffic going back from the computer to each device (in general what ever is needed to support the FTP transfers), and the network will be dedicated to transferring data between these devices and the host computer. Is it possible to use a switch to combine the multiple incoming 100Base-T streams into a single outgoing 1000Base-T stream? if so what features in a switch should I be looking for? Or would it be better to have 3 physical point-to-point 100Base-T dedicated connections between each device and the host computer? (thus having at least 3 physical Ethernet interfaces on that computer) Note that I can't change the interface on the devices, but I am free to choose the network and host computer configuration. Thanks for you help Peter

    Read the article

  • Windows recovery partition with GRUB2

    - by Actorclavilis
    So I recently got a new Toshiba laptop and installed Ubuntu 12.04 on it. Since it is a "Windows 7 Enabled" machine or some other proprietary nonsense like that, a few hardware features are designed only to work with W7. Eventually I found a way to enable these hardware functions by booting into the W7 recovery disc; however, they sporadically stop working. I'm moderately surprised that I was able to get anything to work at all, so I don't especially want to spend more time fixing the problems in a different fashion. Now I don't actually own the recovery disc; it's my father's. Since it's a pain to have to go asking for the disc every time the features stop working, I made an image of the disc and was hoping to make a 'recovery' partition like some computers have. However, unetbootin and GRUB2 both want a kernel and initrd to point to on startup, and something like set root=(hd0,1) loopback lo /w7r.iso set root=(lo) chainloader +1 in the spirit of the makeactive/ chainloader +1 commands that I used to use to dual-boot Linux and Windows simply gives me a file-not-found error. My question, therefore, is: Is it possible to, having written a Windows iso to a partition (such as with dd if=w7r.iso of=/dev/sda4) to a partition, convince GRUB2 to boot from it? Thanks in advance.

    Read the article

  • Liked Arch Linux - but I am still not sure if its the right distro for me...

    - by BlackAndGold
    As the title says... I used Arch Linux for a while and liked it a lot: leightweight, sleek, fast and well documented with a great community. However I had to format my hd and for the sake of being too lazy to reinstall arch, I used windows 7 exclusively for a while. Now I want to get back to linux again (still dual boot), mainly for web development purposes and using handy tools such as rsync ect. Again, I liked Arch, but there is too much tweeking, too much reading up and too much figuring out what to do as well es some bad suprises especially when you need them the least and when just quickly want to get some work done. I kind of would like to have a little more "out of the box" distro that is still fast and somewhat leighweight and of course reliable. I actually considered Ubuntu, which I am not too big of a fan of, but I will still give the minimal install a shot. However other distros seem interesting as well, such as crunchbang and mint debian ecpecially. My question, hoping this isn't too boring for many you, what is the right distro for me?

    Read the article

  • Display stretches 4:3 ratios; Adds scrolling to other ratios

    - by Matt
    I have a dual monitor setup. Normally, they both display at 1680x1050. They have been setup this way for about a year. I'm using Windows XP Professional 2003 x64 SP2. Today, out of nowhere, one of the monitors kicked back to a lower resolution. I was not playing with any configuration at the time.. in fact all I had done was close a window (maybe a browser). But the thing is that the resolution is still preserved partially by the fact that the screen will scroll when you move the mouse. So it's like looking through a 1024x768 window into a 1680x1050 world. The monitor itself does not appear to be damaged, because I also have it connected to my netbook (via KVM) and higher resolutions work fine. I tried uninstalling/reinstalling the drivers to no avail. System restore doesn't help either. I'm unsure of the exact ATI card I'm using.. Device Manager lists it as "Radeon X300/X550/X1050". There is no Catalyst Control Center software installed. I tried to install it, but there doesn't seem to be a way to install it by itself ... it forces you to install another driver, which breaks both of my displays, forcing me to go into safe mode and run system restore again. Any ideas? Thanks EDIT: After playing around more, I discovered that the "scrolling" behavior is only present for aspect ratios that are not 4:3. For 4:3 ratios, it just stretches out to fit the wide screen. My monitor's native ratio is 16:9 .. what could be causing it to think it needs to scroll?

    Read the article

  • Ubuntu network card problem.

    - by Steve Greene
    Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

    Read the article

  • Advice on Computer Specs for overall development/general use machine

    - by Ender
    At the moment I am restricted to a laptop with 512MB of RAM, a 120GB HDD and a 1.5GHz Intel processor for all my development and general browsing needs, and as you can probably tell using it for anything modern is a painful experience. As a result I've decided to buy myself a new desktop computer, one that will stand the test of time and one that can be upgraded easily. Rather than build the machine myself I've decided to go through Dell as I've had good experiences with them when purchasing computers for my family. I've had my eye on this as it's got a good amount of RAM, has a decent-rated processor and isn't priced too badly. http://www1.euro.dell.com/uk/en/home/Desktops/inspiron-580/pd.aspx?refid=inspiron-580&s=dhs&cs=ukepp1&~oid=uk~en~20211~inspiron-580_d005827~~ Intel® Core™ i5 Processor 750 (2.66GHz, 8MB) Genuine Windows® 7 Home Premium 64bit - English Display Not Included ATI Radeon™ HD 5450 1GB DDR3 graphics 6144MB Dual Channel DDR3 [3x2048] Memory 1TB (7200rpm) SATA Hard Drive DVD +/- RW Drive (read/write CD & DVD) with DVD Burn software 1 year of coverage included with your PC McAfee® Security Centre - 15 Month Protection - English After the pain of using a slow laptop for all this time the main thing I want is speed. I may look to play a couple of basic games on it, nothing too powerful. Obviously I'll be doing some development on it too so it'll have to be able to handle the latest IDE's and Database tools like SQL Server pretty quickly. Finally, should I ever need to improve it I'd like to be able to add more RAM and change some of the parts. I wouldn't have thought this would be a problem but a few people I've spoken to have said that the amount of RAM the motherboard can handle isn't that great. Is this true? How long can I expect to be using this computer before it's too slow? Thanks in advance for the help.

    Read the article

  • Nokia E75 Mail for Exchange

    - by Sebastian
    Hi, I have a SBS2003 runing Exchange Server 2003 SP2. My OWA has a godaddy certificate valid for 3 years to come installed. HTTPS works fine for OWA. The certificate has also been copied into the Nokia E95 I am trying to syncronize my Nokia E75 via Mail for Exchange to my mail account on the Exchange server. These are the steps i use: Menu Email New Start Select Internet Gateway Than i enter the details: [email protected] I select company email Mail for Exchange In the domain menu i enter : mydomain In the username/password menu i enter : myusername/mypassword In the server menu i enter : mail.mydomain.com (where the DNS resolves into the server's IP address) In the secure access i select : Internet / Secure / 443 NOTE : port 443 has been opened on my SBOX and forwarded to the exchange server. On IIS default website properties directory security secure communications edit the "Require Secure Channel SSL" is enabled. However, when i try to sync my phone i get the following error code: * Mail for Exch permissions illegal. Check permission configuration. * The phone log gives the following information : Username or Password Illegal. Correct Username and/or Password in the profile options. I've tried speaking with the Phone service support but they cannot identify the problem. Any help will be much apreciated.

    Read the article

  • Windows shutting down, CPU maxing out in Windows-7 32-bit? [closed]

    - by Vivek Sharma
    I have no idea, what is happening to my laptop. For last 5-6 times it has automatically shutdown while running, without doing anything serious. And I even do get the message during boot which says - Start windows normal - Start in safe mode It just boots up normal. Few days ago, my screen blinked and it the PC shutdown immediately. After that I was not able to get it started. I got it repaired, the guy said he has replaced the display chip (nVidia-nvs-140), but i seriously doubt that. Now it started working, but would shutdown every 20 mins or so. I have a dual boot, ubuntu-11.10 works just fine. Virus scan on windows shows nothing. I am pasting my perfmon output. My CPU for reason is maxing out to 100% continously, for windows internal processes. Please have a look at the attached file. Strangly now for last 2 hours it is working fine, but i am just writing emails and reading excels. ThinkPad T61 | t9300 | 3gb | nVidia 140 nvs-quadro (latest driver 296.10) What do you suggest?

    Read the article

  • Ubuntu 12.10, Unity, AMD 12.11 beta drivers, AMD APP SDK 2.7 and OpenCL detection of multiple gpus

    - by junkie
    I'm using Ubuntu 12.10, AMD 12.11 beta drivers, AMD APP SDK 2.7 and OpenCL. I have three amd radeon 7990s plugged in each of which are a dual 7970 so I have six gpus altogether. I plan to go up to eight in a few days. Windows couldn't use even 4 but linux works fine with 6 so far. The strange thing is that the six gpus are only detected by OpenCL in unity (the ubuntu default window manager). If I switch to e17, blackbox or fluxbox or anything else for that matter OpenCL only detects one. I'm using a simple OpenCL program to list all devices to check. I've also checked the output of aticonfig --list-adapters, fglxinfo and clinfo. The first two always show six in all window managers wheras clinfo shows 6 in unity but 1 gpu in all other WMs. I'm also using an X config generated by aticonfig --initial -f --adapter=all. I'm also only using one monitor. I've also checked using lsmod that the fglrx module is loaded in all WMs. So I have two questions. Why does OpenCL see six gpus only in unity? How can I enable six gpus on other lightweight WMs? Basically I'm getting at what determines how many gpus the OpenCL runtime sees? Thanks.

    Read the article

  • Intel Ethernet Bottlenecking Internet?

    - by Donald Darma
    I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

    Read the article

  • Installing Ubuntu guest crashes Hyper-V host

    - by Grant
    I have a weird problem that I don't even know where to begin diagnosing. Trying to install Ubuntu to a VM locks up the host system! My setup is: Dell R715 server, dual 16 core AMD opteron processors, 96GB RAM Dell MD3600f SAN Server 2008 R2 Datacenter System Center VMM 2012 There are 5 windows virtual machines running that have had no problems. This is the first linux VM I've tried to create. I setup a VM through virtual machine manager, set the CD drive to a Ubuntu 12.04 server x64 iso, and started it up. It boots up the normal ubuntu install menu, but the second I hit enter on "Install Ubuntu Server", I get disconnected. The HOST machine stops responding to pings. So do all virtual machines on it. It locks up entirely - keyboard on the host won't work, mouse won't move, numlock light won't change. There's no blue screen - the host is sitting at the login screen completely unresponsive. I can't find any relevant logs in event viewer after rebooting. What could cause the host machine to freeze like that? It's not a one time occurrence - it happens every time at the exact same point. Thank god this server isn't in production yet!

    Read the article

  • How to locate phpmyadmin on ubuntu

    - by Chris
    Okay, I'm usually a windows user and I write quite happily there, unfortunately (or fortunately) I have installed linux on a dual boot and having installed some software I have a question... Where is it? I installed Apache, PHP, MySQL and separately phpmyadmin, Apache is up and running, I've seen my phpinfo page and MySQL is there. MySQL is telling me that there's a database for phpmyadmin, but...erm.. I can't seem to locate it. On a windows machine the directory would be in the www directory and I'd just navigate there... localhost/phpmyadmin/ but on Ubuntu I can't find it in the equivalent. I've been to /var/www/ and there's my index.html (from apache) and my phptest.php file but no phpmyadmin. There is a phpmyadmin in /lib but that only has 2 files in it. So having rambled lots, my question is, what do I have to do to be able to navigate to the phpmyadmin index page? I realise this could fall under the description of a server related question and should be posted elsewhere but as it's software on a home system some help would be appreciated. Do I need to move some files from somewhere? Help! I really don't want to have to go back to developing on Windows as I'll be deploying to a lamp system, my learning curve will be steep.

    Read the article

  • Linux Live CD only works when Windows is in Legacy mode?

    - by Vee
    I have asked a similar question before and no one was able to help me but I think it was because I wasn't phrasing it properly. This is a better restatement of the question. I have Windows 8 and Linux Mint dual booted on my pc. When I tried to boot the Linux from a CD ROM only, it would give me the following error: error: failure reading sector 0x0 from 'hd1' error: you need to load the kernel first. Press any key to continue... The Linux Mint works fine but otherwise, but it gives this error when I try to boot from CD. The boot Linux from CD only worked when I changed the Windows to Legacy mode in the BIOS settings. When I changed it back to UEFI, it would give the same error. Why is this? How can I fix it? I am somewhat new so is there anything else I should know about all of this? NOTE: I changed the Linux into UEFI mode using boot-repair but that still did not solve the problem when I tried to boot from CD ROM.

    Read the article

  • Need Help Scoping a Server to use for study (MCITP Ent Admin + SharePoint 2010)

    - by AVFamily76
    i need to study for mcitp, but i also need to study for sharepoint 2010 i have a poweredge 1850 with two single-core CPUs + two 73G drives - it kills me on electricity, so don't want to use it, and it won't do VT, but it could be one of three boxes for a lab that's cheap, but will cost a lot on electricity i was thinking . . . OPTION #1 Opteron 4170 HE (50 watt chip), 6-core, only two-bills ($200), but the board's are $250, so that's an $800 box, then get another box to dual-boot Win7/Hyper-V on the cheap...? OPTION #2 Used Quad - but how many VM's that are really banging away could it run at same time? (Server 2008r2, SQL 2008r2, Search Server) OPTION #3 Study from books and just get one box that can run two VM's at same time, even if slowly. the last time i had and used a home lab was five years ago when i had a DC, SQL, Exchange and business app box, that's where i got my server skills was just banging on it for four years, but didn't read any books, so now i have to get certified and know the material, and just am not sure how much attention i should pay to the box i use versus the studying time and reading. sorry it's a subjective question, and am obviously open to all sorts of abuse here, but hope you can tell me also how many VM's i can run at the same time given what they'll be doing (SQL and SharePoint FAST search server are resource hungry) thanks!

    Read the article

  • Wired to wireless bridge in Linux

    - by adrianmcmenamin
    I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

    Read the article

  • How can I setup a Proxy I can sniff traffic from using an ESX vswitch in promiscuous mode?

    - by sandroid
    I have a pretty specific requirement, detailed below. Here's what I'm not looking for help for, to keep things tidy and on topic: How to configure a standard proxy Any ESX setup required to facilitate traffic sniffing How to sniff traffic Any changes in design (my scope limits me) I need to setup a test environment for a network-sniffing based HTTP app monitoring tool, and I need to troubleshoot a client issue but he only has a prod network, so making changes to the config on client's system "just to try" is costly. The goal here is to create a similar system in my lab, and hit the client's webapp and redirect my traffic - using a proxy - into the lab environment. The reason I want to use a proxy is so that only this specific traffic is redirected for all to see, and not all my web traffic (like my visits to serverfault :P). Everything will run inside an ESX 4.1 machine. In there, there is a traffic collection vswitch in promiscuous mode that is not on the local network for security reasons. The VM containing our listening agent is connected to this vswitch. On the same ESX host, I will setup a basic linux server and install a proxy (either apache + mod_proxy or squid, doesn't matter). I'm looking for ideas on how to deploy this for my needs so I can then figure out how to set it up accordingly. Some ideas I've had were to setup two proxies, and have them talk to eachother through this vswitch in promiscuous mode, but it seems like alot of work. Another idea is a dual-homed proxy, but I've never seen/done that before so I'm not sure how doable it is for what I'd like. I am OK with setting up a second vswitch in promiscuous mode to facilitate this if need be, but I cannot put the vswitch on the lan (which is used so my browser would communicate with the proxy) in promiscuous mode. Any ideas are welcome.

    Read the article

  • Connect two networks

    - by Meek Barrios
    Connecting two different offices with a wireless link and linux boxes. Hardware: 2 CISCO RV42, 2 Dual Homed Linux Boxes running debian, 2 2Wire and 2 AirMax 5 Configuration is: Office A LAN A (10.1.1.0/24) -> RV42 A (WAN1 - 10.1.1.254) -> 2Wire A (Internet) LINUX A ( ETH0 (LAN) 10.1.1.253, ETH1 (LINK) (10.1.3.3) Wireless Link --- AirMax A <-> AirMax B connected as Wireless Bridge Office B LAN B (10.1.2.0/24) -> RV42 B (WAN1 - 10.1.2.254) -> 2Wire B (Internet) LINUX B ( ETH0 (LAN) 10.1.2.253 -> ETH1 (LINK) (10.1.3.4) Network configuration is: LAN A - Default Gateway 10.1.1.254 RV42 A - Static Route 10.1.3.0/24 on 10.1.1.253 Static Route 10.1.2.0/24 on 10.1.1.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux A - ETH0 10.1.1.253 netmask 255.255.255.0 gw 10.1.1.254 ETH1 10.1.3.3 netmask 255.255.255.0 gw 10.1.3.1 AIRMAX A - 10.1.3.1 netmask 255.255.255.0 gw 10.1.3.1 LAN B - Default Gateway 10.1.2.254 RV42 B - Static Route 10.1.3.0/24 on 10.1.2.253 Static Route 10.1.1.0/24 on 10.1.2.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux B - ETH0 10.1.2.253 netmask 255.255.255.0 gw 10.1.2.254 ETH1 10.1.3.4 netmask 255.255.255.0 gw 10.1.3.2 AIRMAX B - 10.1.3.2 netmask 255.255.255.0 gw 10.1.3.2 Both linux have ip_forward set to 1 and the following on the iptables: iptables -F iptables -X iptables -P FORWARD ACCEPT iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT I can ping from Linux B any ip on 10.1.1.0/24 segment and on linux A any ip on 10.1.2.0/24 segment however I cannot connect to HTTP or FTP on those machines. From LAN A I cannot see any other network. I'm looking for some advice for this configuration or a better solution. Regards

    Read the article

  • Ubuntu 9.10 RSA authentication: ssh fails, filezilla runs fine

    - by MariusPontmercy
    This is quite a mistery for me. I usually use passwordless RSA authentication to login into my remote *nix servers with ssh and sftp. Never had any problem until now. I cannot connect to an Ubuntu 9.10 machine: user@myclient$ ssh -i .ssh/Ganymede_key [email protected] [...] debug1: Host 'ganymede.server.com' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:14 debug2: bits set: 494/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: .ssh/Ganymede_key (0xb96a0ef8) debug2: key: .ssh/Ganymede_key ((nil)) debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: .ssh/Ganymede_key debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Trying private key: .ssh/Ganymede_key debug1: read PEM private key done: type RSA debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password,keyboard-interactive debug2: we did not send a packet, disable method debug1: Next authentication method: keyboard-interactive debug2: userauth_kbdint debug2: we sent a keyboard-interactive packet, wait for reply debug2: input_userauth_info_req debug2: input_userauth_info_req: num_prompts 1 Then it falls back to password authentication. If I disable password authentication on the remote machine my connection attempt just fails with a "Permission denied (publickey)." state. Same thing for sftp from command line. The "funny" thing is that the exact same RSA key works like a charm with a Filezilla sftp session instead: 12:08:00 Trace: Offered public key from "/home/user/.filezilla/keys/Ganymede_key" 12:08:00 Trace: Offer of public key accepted, trying to authenticate using it. 12:08:01 Trace: Access granted 12:08:01 Trace: Opened channel for session 12:08:01 Trace: Started a shell/command 12:08:01 Status: Connected to ganymede.server.com 12:08:02 Trace: CSftpControlSocket::ConnectParseResponse() 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Status: Retrieving directory listing... 12:08:02 Trace: CSftpControlSocket::SendNextCommand() 12:08:02 Trace: CSftpControlSocket::ChangeDirSend() 12:08:02 Command: pwd 12:08:02 Response: Current directory is: "/root" 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Trace: CSftpControlSocket::ParseSubcommandResult(0) 12:08:02 Trace: CSftpControlSocket::ListSubcommandResult() 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Status: Directory listing successful Any thoughts? M

    Read the article

  • Offline productivity

    - by Frank Meulenaar
    On some days I'm commuting 2hs (oneway) in the train. I don't have any mobile internet nor is there always WiFi service in the train. Because of security reasons I can't do any work in the train so I'm trying to work on my geek time. I'm looking for general solutions on how to do this (I'm on FireFox/Windows but I don't think it matters) Email works perfectly with gmail offline. It syncs directly when online and remembers complicated stuff. So far I used the ScrapBook plugin to store an website. It works good, but I have to download my favorite news page every day again - I want it to sync as soon as possible. It would even be more awesome if I could click a page on my desktop and my laptop would sync as soon as it has the chance. (edit: maybe the autosave plugin for scrapbook can do this) Similarily, I use the Downloadhelper plugin to download youtube vids, but I'd like something that automatically downloads videos from a given channel. Any tips are welcome. So far my early morning schedule is: wake up, power on laptop, make coffee, power off laptop and leave within 10 minutes (enough time for GMail to sync) but I can imagine a system where my laptop stays on during the night (or boots before I wake (and makes me coffee :])).

    Read the article

  • How to migrate WinXP from failing old HD to new one

    - by Péter Török
    Following this issue, we have all our important data backed up now. I also bought and installed a new replacement hard disk (WD 160GB PATA) as secondary (slave) drive. I created two primary NTFS partitions on it: a 40 GB system partition, and a 110GB data partition. In theory I could start reinstalling WinXP from scratch on the new system partition, then copying over all user data from the old drive to the new data partition. Once this is done, I could even throw away the old drive, or keep it just to see what happens. (Note: I don't want to clone the whole drive as it contains a dual boot setup with an old Linux installation which I don't need anymore, and anyway, a fresh reinstall would do WinXP good to get rid of many years' clutter.) However, I am lazy :-) The old HD is still functioning, the problem has not manifested again since. So I feel there is no need to hurry with a complete OS reinstall. What I don't know though is whether I will be able to install WinXP on the new system partition at a later stage without affecting the contents of the data partition on the same drive. If this is possible, I can just move over all our data to the new data partition to have it safe, then continue running WinXP from the old drive as long as it works. Does anyone see any problems/risks with this plan?

    Read the article

< Previous Page | 190 191 192 193 194 195 196 197 198 199 200 201  | Next Page >