Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 199/216 | < Previous Page | 195 196 197 198 199 200 201 202 203 204 205 206  | Next Page >

• ipv6 with KVM on debian

  - by Eliasdx

  I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

  Read the article

• Technology mash: is this possible?

  - by Jon Story

  I'm in the process of setting up my own DNS+hosting on a couple of VPS and my home machines, mostly for academic/learning purposes, but also for convenient accessing of my files, hosting my personal websites, private git repositories etc. I've got a main web server with DNS, and a slave DNS server. I've also got a couple of machines at home doing file hosting, video streaming and all that fun stuff. I'm intending to use my VPS's to provide myself with a dynamic DNS system so that I can point mydomain.com at my DNS servers, with home.mydomain.com going into my home network via a raspberry pi. HOWEVER.... I've not got access to the network infrastructure at home (rented accommodation with managed internet), so I can't forward the ports on the router to my own machines. As such, I'm wondering if it's possible to route all the traffic via an SSH/HTTP tunnel through one of the VPS? My plan is to have the raspberry pi provide a VPN into my home network. The raspberry pi uses SSH to connect to the VPS, and the VPS forwards any traffic to home.mydomain.com via the tunnel to the raspberry pi. Is this even possible, and how do I go about it? I don't mind getting my hands dirty with coding and low level tools, I'm just not sure where to start or what the best way to go about it is.

  Read the article

• How to configure a large mtu (linux)

  - by Somejan

  I have a gigabit ethernet connection from my laptop to my router, and a working ipv6 connection to the internet. I can receive very large packets from sites on the internet, with sizes up to at least 10000 bytes (according to wireshark). (edit: turns out to be linux's 'generic receive offload') However, when trying to send anything, my local computer fragments at just below 1500 bytes for ipv6. (On ipv4, I can send tcp packets to the internet of at least 1514 bytes, I can ping with packets up to the configured mtu of 6128 but they are blackholed.) I'm on ubuntu 12.04. I have configured an mtu for my eth0 of 6128 (the maximum it accepts), both using ip link set dev eth0 mtu 6128 and in the NetworkManager applet gui, and restarted the connection. ip link show eth0 shows the 6128 mtu is indeed set. ip -6 route shows that none of the paths the kernel knows about have an mtu set. I can ping over ipv4 with packets up to 6128 bytes (though I don't get responses), but when I do ping6 myrouter -c3 -s1500 -Mdo I get error replies from my own computer saying that the packets are too large and the mtu is 1480. I have confirmed with Wireshark that nothing is put on the wire, and the replies are indeed generated by my own computer. So, how do I get my computer to use the larger mtu?

  Read the article

• C# sends SQL data 4 times less from one box than from another

  - by Bobb

  W2003, .NET 3.5, SQL 2008 I have prod and UAT app servers deployed in 2 different data centres. I have a C# app which reads text file, parse the text and sends the data to the SQL in bulk. SQL server is in US and the app servers are in London (but in different places). All POPs have dedicated network connections. There is no public internet involved. When the app runs on UAT server I can see in Perfmon that the Send byte/sec is x4 higher than from production server. My estimate is that one server outputs at 1 MB/s and the other at 250 KB/s rate. My suspicion immediately is that there is a router on one of the DCs which shapes traffic or does QoS limitation on traffice from London to US. However support and Windows team and networkig team all are saying that there are no differences in neither networking config on the 2 DCs nor NIC config on the 2 app server... How to find out why is the networking bottlneck is 4 times tighter in one place than in the other? What can I do about it?

  Read the article

• dhcp3-server (dhcpd) is tampering with host NIC

  - by user61000

  Hi all, I have a debian box that is serving as a router (using iptables NAT). When first turned on, everything works fine for a few minutes. Then the dhcp server assigns an IP (other than 192.168.0.1) to its' host NIC, eth0. This is NOT what I want. I just want dhcp3-server to listen on eth0, not assign it an IP, and changes the kernel routing table. This of course ruins the NAT capablities of the box. How can I tell the dhcp3-server NOT to do this? Thanks Before dhcp3-server tampers with eth0, the IP is 192.168.0.1, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 173.33.220.1 eth1 After dhcp3-server tampers with eth0, the IP is 192.168.0.3, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 192.168.0.1 eth0 default 173.33.220.1 eth1 SETUP Outbound NIC is eth1 Internal NIC is eth0 /etc/network/interfaces ... iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 /etc/default/dhcp3-server INTERFACES="eth0"

  Read the article

• Unable to mount root fs over NFS [on hold]

  - by johnmadrak

  I am attempting to set up a Raspberry Pi running Pidora to boot from an NFS share. My configuration in cmdline.txt is: dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/nfs nfsroot=<serverip>:/fake/path,nfsvers=3,rw,nolock nfsrootdebug ip=dhcp elevator=deadline rootwait On the Pi, the output I see is: IP-Config: Got DHCP answer from <router>, my address is <clientip> IP-Config: Complete: device=eth0, hwaddr=<macaddress>, ipaddr=<clientip>, mask=255.255.255.0, gw=<routerip> host=<clientip>, domain=, nis-domain=(none) bootserver=<routerip>, rootserver=<serverip>, rootpath= nameserver0=<routerip> (It pauses for a bit here) VFS: Unable to mount root fs via NFS, trying floppy VFS: Cannot open root device "nfs" or unknown-block(2,0); error -6 Please append a correct "root=" boot option; here are the available partitions: ..... On the NFS Server (an OpenVZ Container), the output I see in the /var/log/messages is: Aug 22 23:24:01 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:783 for /fake/path (/fake/path) Aug 22 23:24:38 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:741 for /fake/path (/fake/path) Aug 22 23:25:25 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:752 for /fake/path (/fake/path) Aug 22 23:26:12 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:876 for /fake/path (/fake/path) To test, I've made sure I can mount (non-root) from both the Pi and another machine and it worked. Does anyone have an idea on what could be wrong or how to narrow it down? Thank you in advanced for your help.

  Read the article

• Logitech Performance MX Mouse Jumps on OS X Lion (10.7.4)

  - by Adam Thompson

  I have a Logitech MX Revolution wireless mouse that I am trying to use with OS X Lion. Everything is working except for one problem... there is a small, but quite noticeable, jump when the mouse cursor is moved. The problem is mostly prevalent when dragging and dropping files or trying to highlight items. It makes performing any task with the mouse accurately next to impossible. I did quite a bit of looking and found that all kinds of people have had mouse issues with OS X. I've tried all of the following with absolutely no success: Using the official drivers from Logitech (these performed worse than the default mouse drivers in OS X) Using SteerMouse as a third party mouse driver. This worked ever so slightly better than the default driver, but still suffered quite frequently from the skipping problem Cleaning the sensor on the mouse and ensuring it's not the result of the surface that it's being used on. Tested the mouse on a Windows machine. The mouse worked absolutely flawlessly on the other machine. Changed the channel that my wireless router operates on by the off chance my problems were the result of interference. This also had no effect. I can't think of anything else that could possibly interfere with the mouse. I'm am out of ideas on what to try, so I would really appreciate if anyone has any suggestions. I should also mention that an old wired mouse I had laying around worked just fine when I plugged it in. This really isn't the best solution, however, as I really prefer the MX Revolution.

  Read the article

• Sparc Solaris 2.6 will not boot

  - by joshxdr

  I have a very old Sparc Solaris network that was working fine last week, but after a power outage none of the workstations will boot. The network looks like this: host A: solaris 2.6, shares /export/home to network by NFS host B: solaris 8, runs NIS server. Mounts /export/home/ by NFS. host C: RHEL5, shares /share to network by NFS. Mounts /export/home/ by NFS. I figured that the main problem was host A, since you need the home directories available for the other workstations to boot(?). Host A does not mount anything by NFS as far as I know. However, this workstation will NOT boot. The OBP bootup sequence looks like this: Boot device <blah> configuring network interface le0 Hostname <hostname> check file system <everything ok> check ufs filesystem <everything ok> NIS domainname is <name> starting router discovery starting rpc services: rpcbind keyserv ypbind done setting default interface for multicast: add net 224.0.0.0: gateway <hostname> <HANGS at this point> Is there some kind of debug mode so that I can get more detail as to why the workstation won't boot? Is my network structure inherently susceptible to power outage? Is there a way I can boot up to command line so I can at least turn off the NFS mounting?

  Read the article

• ipv6 with KVM on debian

  - by Eliasdx

  I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

  Read the article

• Windows 7 ICS client web failure

  - by n8wrl

  I have several windows 7 PC's connected on a LAN via a hub. One has a Verizon 3G connection and works great. I have internet connection sharing enabled on it, which automagically set the LAN connection to 192.168.137.1 and enabled DHCP. I am trying to get the client PC's working one at a time. The others are off. The client is able to: Get an IP via DHCP with correct settings. Ping any web address I can throw at it, so DNS and routing are working. Windows update works. But web sites hang in IE. All but google.com! I type www.msn.com, microsoft.com, amazon.com, etc. etc. All ping via a cmd window but IE just hangs - it says web site found but the green progress bar just slowly creeps and no content displays. www.google.com comes up even after clearing browser and dns cache. I am pulling my hair out - what am I missing? EDIT: After some more gyrations with a router I'm back to ICS. Same symptoms, only now I have an answer to Andrew's question, YES I can do Google searches but clicking on any of the result links hangs! Let one sit for half an hour with no timeout or error.

  Read the article

• Trouble in Team Viewer VPN Connection

  - by Sumit Pal

  I have completed initial vpn connection setup. It has connected. I have tested with ping and it is ok. My problem is, when I want to start file transfer in VPN it asks for username & password. So what is the user name? I have tried giving Computer-Name/User-Name. I have found my Computer Name by going to Control Panel/System/ & clicking 'Computer Name' tab & username from user accounts or it is shown when I login in windows account (Please correct me if the above procedure is wrong). But what is the password? I have tried giving the account password but it always give 'The username or password is incorrect.' My Question: How to find the username & password? For Information: a) I have Team Viewer 7 installed in one Windows XP PC & one Windows 8 PC. I like to create a secure connection between these two PCs. b) The two PCs are connected in the same local network via a router. Please ask if you need additional information.

  Read the article

• Route return traffic to correct gateway depending on service

  - by Marnix van Valen

  On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

  Read the article

• Windows 7 remote desktop encryption error every few minutes

  - by rfrankel

  Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

  Read the article

• How to prevent asymmetric routing with multiple eBGP routers?

  - by Andy Shinn

  I have 2 routers announcing a /22 subnet to different providers (one providers connects to each of the 2 routers). I have split the /22 in two /23 to announce one /23 on each of the routers plus the /22 (the providers will take the more specific route). This allows me to fail over and keep traffic inside the /23 in and out the same provider. What are other ways in which I could announce just the /22 with both routers and have packets from servers on the network behind the routers go back out the same router in which they came in from? EDIT: The main problem I come across, which end users and clients complain about the most, is that the least hop route is sometimes not the "optimal" route. In my case, I know that Provider B may have better latency to X nation. But when packets come in from provider B, they may go out Provider A or provider B. The reverse is also true. If I send a packet to X nation out provider A, even though it may have more hops back, the packet will likely come in from Provider B (which may have higher latency, packet loss, etc. to this nation)

  Read the article

• Network Security Device/Software

  - by Campo

  We currently run Symantec Antivirus Corporate 10.2. The software is really easy to manage on a network but the actual virus detection isn't bad but the malware detection is crap. We recently were infected with a email bot that got us put on some block lists. This has been resolved. I cannot have that happen again. I would like to find a program as easy to manage as symantec that I can install on all the user's workstations as well as the servers. We run a windows 2003 domain. We have a couple 2008 test servers in the environment. Most of the workstations are xp though I am using windows 7 and symantect is not compatible with this OS... So we need a solution that would cover all those operating systems. If it could be installed on macs too that would be a bonus though not necessary at all. This software must detect: Viruses AND Malware I am looking for something that combines the features in anti-malware programs like malwarebytes or spybot with an antivirus program like symantec or AVG. Alternatively if there is a piece of hardware that is a firewall, router, and packet inspection for virus/spam that would be the most ideal solution. I then could supplement with a piece of software that could pickup what the hardware misses. Thank you for your suggestions.

  Read the article

• Access server using IP on another interface

  - by Markos

  I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

  Read the article

• DNS lookup fails when with all the MAC workstations

  - by user39564

  Hi, I am having this insane problem. We are mac-heavy users. Around 10 workstations, one Xserve server, two windows workstation and one Linux (me). Last year I added an A record to our domain's DNS. However we had to change that a few months ago to a new IP. But all the Mac workstations fail to resolve the proper DNS and they still resolve to the old IP, even after 2 months. On both the windows workstation and my linux box a simple nslookup resolves to proper IP. However, on ALL the mac workstation, dig and nslookup report the old IP address. From my linux workstation: jp@lo:~$ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 68.71.40.xx But when I am trying the exact same command from any Mac workstation, I get the old IP: $ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 98.143.155.xx The strange thing is that this only happens in our internal network. No problem from home nor from another server. I did try to flush the DNS, don't worry. It did not help. I am starting to wonder if my router (OpenWRT) or Mac OS X Server is not in some way spoofing the DNS request and thus acting as a cache. Any suggestions/comments would be grateful. Thank you, JP

  Read the article

• Track kids browsing history even when they know how to clear it manually

  - by Darren Newton

  I have a colleague with two teenage boys (yes, cue cliche's about 'I have this friend see...') He's currently having issues with them browsing pr0n and wants to do a little spying on their browsing (I'm staying clear of the philosophies/ethics on this.) The kids are savvy enough to clear their browsing history when they're done. As I'm his goto for IT he has asked me if there is a way to keep a hold of the browsing history. The family uses Macs, and the kids surf with Safari. I know that browsing history is kept here ~/Library/Safari/History.plist. I figure there should be a way to write either an AppleScript or other script (Python/Ruby/Bash) that can backup this file to a different location (/opt/local/history, etc.) Since the kids know to clear their history when they're done should the file be periodically backed up with something similar to a cron job or something like Hazel? While that could work it seems like it would create a ton of little incremental backups. Or is it possible to 'watch' ~/Library/Safari/History.plist and incrementally add changes to a backup file (saving a diff so to speak) but not lose any data? Any ideas/solutions appreciated. UPDATE/EDIT: Got the word from concerned dad that the oldest uses Firefox on a different PC, so the OpenDNS solution (preferably at the router level) is the best answer so far as it would capture usage for the whole house.

  Read the article

• Setting Remote Desktop to allows IPv6 connections

  - by Garrett

  Setup: Basically I have 3 machines (2 virtual and 1 physical) that I would like to be able to RDP in to from outside my NAT (a router). The VMs are Windows 7 and Windows XP, both fully patched with Teredo installed and working, both running in VirtualBox (their host also has Teredo working, though I'm not sure if that matters). They both have bridged network adapters with promiscuous mode enabled. The physical machine is Windows 7 fully patched with an HFS server running on it and a dynamic DNS set up for my public IPv4 address and port forwarded. It also has Teredo installed and working. Symptoms: According to http://test-ipv6.com/ all 3 have public IPv6 addresses, and they can all connect to http://ipv6.google.com/. I can ping the XP VM from the host it's running on but I cannot ping it from any other machine. Also, I cannot ping either of the other machines from anywhere. I cannot connect to any of them over RDP from IPv6, however I can connect to all of them through IPv4. Any ideas what is going wrong?

  Read the article

• Wireless card overheating?

  - by Sidney

  Ok, so I've had my laptop for several years (I wanna say 4, but possibly more), it's a Toshiba Satellite. I'm running Linux mint 15, and am having a strange new issue, after several hours of running my wireless stops. It can SEE wireless networks, but refuses to connect to any of them. (On a sidenote, connecting to a router with a cable at this point works fine) The fact that it can SEE the networks make me think the card is in good condition, and it's software related The fact that it works for several hours before booting me makes me think perhaps the transmitter is getting too hot. I don't use my laptop in dusty environments, and keep it on an elevated surface (alternatively, I actively try not to let it sit on soft surfaces where the vents get covered). I spray out the cpu fan about once a year with compressed air about once a year, so I really don't think the insides should be too dirty. Finally, unfortunately, sensors only gives me CPU temps, but they run about 40-50 degrees C, which from my understanding is perfectly normal for an I3. Does anyone have any suggestions on what I can do to determine the root cause of this?

  Read the article

• which vista services can be disabled with impunity?

  - by GwenKillerby

  I use Vista on a HP pavilion DV2 laptop. When I look through all the services my laptop starts, it really seems there's way too much of it. I multi boot with XP and 7. Both startup in 40 seconds. Vista takes four minutes. Is there some software that can determine which services I don't need? On 7, there's no propietary HP stuff at all, yet it seems to run fine. Because all these service, there's a LOT of them and some just sit there doing nothing, monitoring for updates I don't really need or want or need to know about the second they're available. my laptop is the only computer i use at home, there's no home network, aside from the modem-router, which is cabled, not wifi. Take for instance Parental controls, and stuff for people with bad eyesight, Tablet PC. I really never use any of that stuff. Hope this question is specific enough. I've looked at the other questions but they didn't answer me. thanks, Gwen.

  Read the article

• What can I do with a home server?

  - by Joel Coehoorn

  I have an old 700 Mhz Pentium III at home running Windows 2000 Server, with a home router set up to pass incoming requests to it and a DynDNS account set up so it's easy to find. Right now I'm using it for a number of things: Shared folders + backup inside the home network Shared Printer inside the home network Domain Controller, just because I feel like it and because it's useful to me as practice to keep those "enterprise" administration skills. Web Server FTP remote access for my files. I abandoned this for security reasons, but it's still worth leaving visible. Remote Desktop in to the home network (thinking about adding VPN service) SVN repository MySQL - Will be moving to SQL Server 2008 Standard soon. After I upgrade my wife's laptop from home to pro later this year it will also become a domain controller It's the only place I still have access to Internet Explorer 6 any more without setting up a new virtual machine, so I use it for testing code with that browser. The question is: What else could I be doing with this machine? Update Additional ideas based on the suggestions: Media Server/DVR Build server PBX SSH Proxy Server Continuous Integration Server Personal OpenID Provider Update2 Just a note that this server was recently upgraded to an Atom330 with 2 GB ram and bigger hard drive. For all that's slow for a "modern" cpu, it should still be much faster than the old Pentium III and the expected power savings should make the upgrade essentially free over the course of the next year or two. Also, it's now running Windows Server 2008.

  Read the article

• iTunes Home Sharing only works one way between 2 Windows XP PC's on the same LAN

  - by scunliffe

  Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the Windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

< Previous Page | 195 196 197 198 199 200 201 202 203 204 205 206  | Next Page >