Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 202/216 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >

• Linux as a gateway (no NAT)

  - by Hugo

  I'm trying to configure a linux server as a gateway/router, but I can't get it to work, and all information I've managed to find is NAT-related. I have a public IP block for the gateway and devices behind it, so I want the gateway to simply route packets to the internet - again: no NATing! I've managed to get the gateway to access the internet successfully (that was just a matter of configuring the IP and GW), and the computers behind it can communicate with it. [EDIT: more info] This is actually an IPv6 block (2800:40:403::0/48) (but I've found that most utilities and instructions can be easily adapted from IPv4 to IPv6 with little hastle). The server has too ports: wan: 2800:40:403::1/48 lan: 2800:40:403::3/48 One of the computers behind it is connected to it via a switch; 2800:40:403::7/48 The wan interface on the server can ping6 www.google.com without issues. The lan interface on the server and the client can mutually ping each other without issues (as well as SSH, etc). I've tried setting the server as a default gateway for the client, with no luck: client # route -A inet6 add default gw 2800:40:403::3 dev eth1 server # cat /proc/sys/net/ipv6/conf/all/forwarding 1 I don't want any filtering/firewalling/etc, just plain routing. Thanks.

  Read the article

• Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

  - by Brandon Bearden

  Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

  Read the article

• Windows 7 Sharing issue on RAID 5 Array(s)

  - by K.A.I.N

  Greetings all, I'm having a very odd error with a windows 7 ultimate x64 system. The network system setup is as follows: 2x XP Pro 32 Bit machines 1x Vista ultimate x64 machine 2x Windows 7 x64 Ultimate machines all chained into 1x 16 port netgear prosafe gigabit switch, the windows 7 & vista machines are duplexed. Also there is a router (netgear Rangemax) chained off the switch I am basically using one of the windows 7 machines to host storage & stream media to other machines. To this end i have put 2x 3tb hardware RAID 5 arrays in it and assorted other spare disks which i have shared the roots of. The unusual problems start when i am getting Access denied, Please contact administrator for permission blah blah blah when trying to access both of the RAID 5 arrays but not the other stand alones. I have checked the permission settings, i have added everyone to the read permission for the root, i have tried moving things into sub directories then sharing them. I have tried various setting combinations in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa and always the same. I have tried flushing caches all round, disabling and re-enabling shares & sharing after restart as well as several other things & the result is always the same... No problem on individual drives but access denied on both the RAID arrays from both XP & Vista & Windows 7 machines. One interesting quirk that may lead to an answer is that there is no "offline status" information regarding the folders when you select the RAID 5s from a windows 7 machine yet there is on the normal drives which say they are online. It is as if the raid is present but turned off or spun down but as far as i was aware windows will spin an array back up on network request and on the machine itself the drives seem to be online and can be accessed. Have to admit this has me stumped. Any suggestions anyone? Thanks in advance for any fellow geek assistance. K.A.I.N

  Read the article

• iptables (DNAT)

  - by user1126425

  I have a host that acts as a gateway for other hosts. The configuration is such that eth0(192.168.1.3) is connected to internet via a router and eth1(172.16.2.50) is connected to internal network via switch. Given that, this host is also running a service that is bound to eth1 and serves the internal network. I want to extend this service to the outside world as well and was trying to manipulate iptables so that any request that comes to this host via eth0 and is directed to 192.168.1.3:80 is send to 172.16.2.50 and internet users can also make use of the service. Here are my iptable rules for setting up the host as gateway (and these work fine): sudo iptables -t nat -A POSTROUTING -s 172.16.2.0/16 -o eth0 -j MASQUERADE sudo iptables -t nat -A POSTROUTING -s 192.168.1.0/24 -o eth1 -j MASQUERADE sudo iptables -A FORWARD -s 172.16.2.0/16 -o eth0 -j ACCEPT sudo iptables -A FORWARD -d 172.16.2.0/16 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT And these are the rules that I am trying to add to the iptables to achieve my ends: sudo iptables -A INPUT -d 192.168.1.3 -p tcp -dport 80 -i eth0 -j ACCEPT sudo iptables -t nat -A PREROUTING -d 192.168.1.3 -p tcp -dport 80 -j DNAT --to-destination 172.16.2.50:80 sudo iptables -t nat -A PREROUTING -s 172.16.2.50 -p tcp -sport 80 -j SNAT --to-source 192.168.1.3:80 sudo iptables -A FORWARD -d 192.168.1.3 -p tcp -dport 80 -m state --state ESTABLISHED,RELATED -j ACCEPT When I do so, I get error like : "multiple -d flags not allowed" ... Can someone tell me how to resolve this error... and do the entries that I want to add will serve my purpose ? Thanks!

  Read the article

• Suggestions for transitioning to new GW/private network

  - by Quinten

  I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

  Read the article

• Bind9 not doing anything with forwarded query responses?

  - by Rykaro

  I have a Bind DNS server that is the local production DNS server and a Windows 2008 R2 domain controller which provides DNS for a lab environment with the domain xyz.lab. I've configured the Bind DNS to forward DNS requests for the domain xyz.lab to the Windows DNS server with this config: zone "xyz.lab" { type forward; forward only; forwarders { x.x.x.x; }; }; zone "x.x.x.in-addr.arpa" { type forward; forward only; forwarders { x.x.x.x; }; }; And Bind options are (the all_internal acl includes the subnets of both the production and lab networks as well as the loopback of the bind server): allow-query { all_internal; }; allow-recursion { all_internal; }; allow-transfer { none; }; notify no; minimal-responses yes; version "unknown"; Unfortunately, when I do an nslookup or dig on the bind server for a host on the lab domain, the request times out. The logs on the Windows 2008 DNS server show it receiving the query and responding to it and a network packet trace shows the query responses arriving at the Bind DNS server. The servers reside on the same switch with a router providing connectivity between the layer 3 subnets (production and lab are on different subnets) and there is a round trip time of between 3ms and 5ms on pings between the two servers, so I don't think there is an issue with latency causing a timeout of the query. In summary a query-response arrives back at the Bind server and the nslookup/dig times-out. Why does the Bind DNS not seem to be doing anything with the query responses when it receives them?

  Read the article

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• Windows 7 VPN only works if I connect it to itself first

  - by user1799075

  Just so you have some detail, VPN request are port forwarded from a linksys router hosting the global static IP (to the world) to the windows 7 machine. The ports have been added to the OK list. I have the incoming VPN connection setup on win 7 but the only way it will work from anywhere outside the physical machine is if I connect from itself to itself first. For example, let's say my internal static IP is 10.0.0.50 and incoming VPN server connection IP is 10.0.0.80 (both on the same machine). I can't connect via VPN from anywhere unless I first VPN from the machines .50 address back to itself on the .80 address. Once I do that, I can connect form anywhere, even my phone. It's as if once the machine reboots it thinks it should block requests on .80 until .50 connects first. BitDefender antivirus/firewall is loaded (windows firewall is off) I don't see anywhere to exclude ports in the BitDefender control panel. Maybe this initial connection opens the ports and tags them as safe because the initial request came from the same machine? Any thoughts? It's driving me nuts and I'm sick of having to drive half way across town over to the server, try to get building access and do the initial connection. Please help

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by user57019

  I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Am I obliged to use ipv6 tunnel services if I want to be able to use it?

  - by Zagorax

  I was looking for configuring Slackware to use ipv6 but all instruction I found speak about using an ipv6 tunnel that encapsulate ipv6 request into ipv4 packet and send them to an external router that extracts ipv6 request and sends a reply (or, at least, this is what I understood). Is that necessary? Isn't there a way to configure a pure ipv6 system? If yes, could you please point me to a guide that clearly explain how to enable ipv6 without this trick? I would like to configure my Slackware desktop at first, and then do the same with my Centos server. EDIT: maybe I gave you too few information. Sorry. I'll write some more information thanks to the posted guide. ~$ test -f /proc/net/if_inet6 && echo "Running kernel is IPv6 ready" Running kernel is IPv6 ready So, it seems ipv6 is enabled in my kernel. Some other output from ifconfig, route and /etc/resolv.conf content (with opendns): ~$ /sbin/ifconfig wlan0 | grep inet6 inet6 addr: fe80::21f:3bff:fe60:cc5b/64 Scope:Link ~$ /sbin/route -A inet6 | grep wlan0 fe80::/64 :: U 256 0 0 wlan0 ff00::/8 :: U 256 0 0 wlan0 ~$ cat /etc/resolv.conf inet6 nameserver 2620:0:ccc::2 nameserver 208.67.222.222 nameserver 208.67.220.220 But still, with ping6 I can only ping localhost (::1). Everything else is unreachable. Normal ping works fine. That is why I was asking if I am obliged to use a tunnel.

  Read the article

• Summer daylight time not changing on some active directory domain clients.

  - by Nick Gorbikoff

  We just had a summer daylight change in US. and pc's on my network are behaving strange, some of them change time and some didn't. My network: 2 locations both in Midwest, same time zone. Location 1: 120 pcs (windows xp & windows 200) , with 1 Active Direcotry Domain Controller on Windows 2003 Standard. A couple of windows 2000 servers (they up to date) the rest of the servers are Xen or Debian machines (all up to date) , Second location connected through OpenVPN link all pc's are running fine - but they are all connecting to our AD domain controller. Locaiton 2: 10 pcs, and a shared LAN NAS. Both of the routers/firewalls in both locations are pFsense boxes with ntp service running - but it's up to date. Tried all the usual suspects: I have all the latest updates installed restarted them domain controller is running fine most computers are running fine I have only one domain controller on my network also my firewall serves as ntp server (pfsense) but it's up to date. all of the linux machines are fine since they are querying firewall / router for the time. about 1/3 of my pcs are 1 hour behind. If I change them manually they just change back ( the way domain pc's are supposed to). I've tried everything but I can't think of anything else to try.

  Read the article

• Does cloud computing offer this? [closed]

  - by TheBlackBenzKid

  I have some newb questions I want answering please about cloud hosting - we are currently looking at Rackspace and getting a windows box. This is the situation: We have 15 computers in our office. We have 3 printers, some wifi and some network plugged. We have a standard router and the office share things via dropbox. The computers are not on Windows SBS or something similar. We want a cloud hosting solution that will offer User can login on any machine in the office and see the machine software User can login on any machine in the office and open Outlook and their emails and signature will be on exchange automatically A shared company folder on the network All printers automatically installed on the network Users can login remotely to access emails via the web At the moment we have a network company saying we need Xeon server in house with backup and psu and Windows SBS with license for each machine and also we need cabinets and cabling setup and also load balancers and modification of our DNS for emails. My question is this. Can cloud offer this? Can we have a server in the cloud that does this? Is it possible I mean the computers would be wireless connected to this cloud and you turn the machine on and its hosted?

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by Melot

  Hi! I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Why can't I connect to my home SSH (SFTP) server? What am I doing wrong?

  - by Rolo

  I am new to this topic of creating a SFTP server on one's computer. I would like to be able to access the folder on my Windows XP computer via SFTP from another computer or a phone. The following is what I have done so far: I have installed SSH Windows and everything is setup correctly because I can access it (the folder on my pc) via WinSCP. I however cannot access it from my phone. It doesn't connect. The phone can be on the same wireless network as the Windows XP computer, but I would prefer to be able to access this when not in the same network. Now, from what I have read and understood, the following is the information needed to connect: 1) Host Name: This would be my computer's ip address which I access by typing ipconfig in a cmd prompt (I access this easily on my computer because I simply put in localhost or 127.0.0.1) 2) Port Number: That would be port 22 (I have also added this to my router in the port forwarding section). 3) Username: This would be my Windows XP username. This however is my full name, including my middle initial followed by a period. I am wondering if this is maybe causing problems in accessing it from my phone, since the name has spaces and punctuation (the period). 4) Password: The password of my Windows XP computer Extra Info: When I say phone, I mean an Android phone and I am using an ftp / sftp app to access my pc via the phone's cellular network (I also tried the wireless, but that didn't work as well). I have tried more than one program. On one program it tells me Connection timed out and on another it tells me "timeout:socket is not established" Also, I know that I can use the site noip, but I prefer to connect this way first. Also, because I am new to this, I would like to look into what exactly noip is doing and if they would be seeing my files as they are transferred from phone to pc. Thanking you in advance for your help.

  Read the article

• Tunnell network requests with Windows 7

  - by mark

  I've Windows 7 64bit Pro client in a private LAN behind a Netgear wgr614v7 router. I've also a remote Debian server machine outside. I'd like to tunnel all (or specified ports/protocols) over this outside server, so when I'm on the Windows machine and I request serverfault.com it would not appear from the wgr614v7 public IP but from the server. But it's not only about HTTP traffic, it's basically about everything I'd like to: other TCP ports, even UDP, etc. It must be transparent to the application, e.g. they shouldn't be aware of this. All their requests just appear as being from the server and the tunnel between them takes care about the packets. I'm aware of e.g. Putty and forwarding individual ports or using it as a socks proxy, however not many applications to support this and the support in windows itself looks non-existent to me. I might add it should be something "reasonable" easy to set up. I've heard about PPTP but I'm unsure about it's security implications (by design). Should I go for VPN? There seem to be two common solutions for Linux (OpenSwan and StrongSwan), why would I pick the one over the other? I also fear that setting up a VPN might be quite complex, OTOH maybe it's the only sane way to do the things right? Or is OpenVPN sufficient? I'm seeking for open (source) solutions, what other options to I have or which direction should I head to?

  Read the article

• 5 year old server upgrade

  - by rizzo0917

  I am looking to upgrade a server for a web app. Currently the application is running very sluggish. We've made some adjustments to mysql (that's another issue in itself) and made some adjustments so that heaviest quires get run on a copy of the database on another server was have as a backup, however this will not last that much longer and we are looking to upgrade. Currently the servers CPUs are (4) Intel(R) XEON(TM) CPU 2.00GHz, with 1 gig of ram. The database is 442.5 MiB, with about 1,743,808 records. There are two parts of the program, the one, side a, inserts and updates most of the data. Side b, reads the data and does some minor updates. Currently our biggest day for side a are 800 users (of 40,000 users all year) imputing the system. And our Side b is currently unknown, however we have a total of 1000 clients. The system is most likely going to cap out at 5000 side b clients, with about a year 300,000 side a users. The current database is 5 years old, so we can most likely expect the database to grow pretty rapidly, possibly double each year (which we can most likely archive older records if it comes to that). So with that being said, should we get a server for each side of the app, side a being the master, side b being the slave, any updates made on side b are router to side a. So the question is should i get 2 of these or 1. 2 x Intel Nehalem Xeon E5520 2.26Ghz (8 Cores) 12GB DDRIII Memory 500GB SATAII HDD 100Mbps Port Speed And Naturally I would need to have a redundant backup so it could potentially be 4 of them.

  Read the article

• Directory service unavailiable, new hardware same settings

  - by Alex

  I'm working on a project with 2 sites connected by a VPN. Site 1 has the main server and there is a secondary server at site 2 which I am trying to replace. The current setup works perfectly however I can't for the life of me get the replacement server at site 2 up and running. I'm trying to replace like for like just upgraded hardware. I have installed the OS (all Server 2003 Standard SP2) and used exactly the same settings as the old server. I have setup Active Directory, DNS Server, DHCP Server and WINS Server configured. I have used all the same settings as the old server (except IP address and name). I can access the active directory but I can't do anything; add, edit, delete all returns "the directory service is unavaliable". No-one can login on any of the computers on site 2 and the internet is down. Plugging the old server back in and connecting it to the network rectifies the issue (so both new and old are connected at site 2), everyone can login and the internet is back (curious since the modem connects direct to the switch, and even with the new server online I can connect to the router via IP but not the net). I really don't have much experience but I've been roped into doing this because my company is too cheap to hire a real network admin. Any suggestions of where I can start to troubleshoot this, its driving me crazy and I only have a day before all the users are back on site.

  Read the article

• FTP timeout but SSH is working?

  - by nmarti

  I have a problem in my server, when I try to connect via FTP to a domain, the connexion is VERY slow, and I get timeouts just listing files in a directory. When I try to connect to the domain folder using the root user account via SSH, it works fine, and I can download the files without problem. What can be wrong? I tried to reboot the server, also the office router, and nothing... It is a fedora core 7 server with proftpd. Can it be a filesystem problem? Thanks. CONNECTION LOG: Cmd: MLST about.php 250: Start of list for about.php modify=20120910092528;perm=adfrw;size=2197;type=file;UNIX.group=505;UNIX.mode=0644;UNIX.owner=10089; about.php End of list Cmd: PASV 227: Entering Passive Mode (***hidden***). Data connection timed out. Falling back to PORT instead of PASV mode. Connection falling back to port (PORT) mode. Cmd: PORT ***hidden*** 200: PORT command successful Cmd: RETR about.php Could not accept a data connection: Operation timed out.

  Read the article

• Connect from Mac OS X to Windows 7 Desktop

  - by jrn

  I am trying to connect from my MacBook to my Windows 7 machine within my own network - if it will work from outside my network that's a plus but no need to have. My Windows 7 machine is freshly installed with Windows 7 Home Premium. It runs the built-in firewall with no settings changed so far as well as Microsoft Security Essentials. So far I tried CoRD and Microsofts Remote Desktop Connections to connect from my Mac to my Windows machine without any success. I did try and disabled the firewall on my Windows machine but could not connect either. The reason I did this was to check wether there is a Windows firewall setting preventing me from connecting. On top of that I manually started the Remote Desktop Services and Remote Desktop Configuration within services.msc. Is there anything else I have to enable for a remote desktop connection? Could there be any router setting I have to tweak? Since I do not want to connect from outside my own network I thought I don't have to do any port forwarding. The error messages I retrieve are all connection timeouts. I can however ping the hostname and/or IP address. Any help would be greatly appreciated. Thanks a lot, jrn

  Read the article

• CentOS and OpenSSH [on hold]

  - by Stephen

  I've recently installed CentOS 6 on an old Dell PC. I'm trying to setup OpenSSH at the moment, I been following some tutorials (http://www.youtube.com/watch?v=QKafb0koJEg) on You Tube, while they have been very helpful I'm at the point where I need to ask some questions. My goal here is to be able to access the server from my work computer and from my personal laptop (which will be on the same home network as the server). I've installed OpenSSH with no issues. So the first thing I was advised to do was port forwarding. So in the sshd_config file, I've changed Port 22 to Port xxxx (where xxxx is a obviously a four digit value). I then restart the sshd service. I've also configured my router for forward port 22 onto xxxx. Is there anything else I need to do? I've generated the keys on my laptop, and I'm trying to copy them to the server as follows: scp id_rsa.pub xxxxxxxx@localhost:.ssh/authorized_keys but this command fails with the following error message: ssh: connect to host localhost port 22: Connection refused lost connection Any help appreciated. Regards...

  Read the article

• Need solution for Network/Servers.

  - by rehanplus

  Dear All, Please help me. I just joined a new Hospital and want some help managing my network. There are some requirements: Current Network: There is a D.S.L connection and that is terminated on a LINUX proxy and then connected to D-Link layer 2 switches and then providing internet to more then 200 PC's (Would be increasing to 1500 in couple of months). D-Link switches are not configured yet. Also there is one Database server Report server and an application server. In near Future Application should be accessed by local users as well as remote users from internet via our web server. We do have a sharing server and all these servers databases and PC's are on single sub net. Required Network: All i do want is to secure my network from outside access and just allowing specific users via web application and they will be submitting there record for patient card and appointment facility by means of application and entering there record (on our database) but not violating our network resources. Secondly in house users also need to access the same application and also internet but they must have some unique identity and rights (i.e. Finance lab dept. peoples do have limited access to that application). Notes: Should i create V LAN or break sub nets. Having a firewall will solve my issues? is a router needed on these type of scenario's. Currently all the access are restricted from Linux Proxy. Thanks.

  Read the article

• oracle access on vmware fusion

  - by gaudi_br

  Hello, I'm running snow leopard and I'm doing some development that requires some network knowledge. I've installed vmware fusion 3.0 and I've set up a virtual machine with windows 2003 server. I need to mimic the exact configuration of another server in the network, so I really need to run the versions I'll be mentioning here. Besides, I set up two network configurations on the VM: one NAT config (so that I can have internet access) and one host-only config (because I need to use another server's mac adress and my local area network might have a problem with it) From the installation of windows 2003, I then installed oracle 10.2.0.1. During the installation I received a warning about the primary ip-address of the system being dhcp assigned, but I ignored it (maybe it was a mistake)... Now, from experience, unless the DHCP assigned address changes, I should be able to access the guest system's database from the host system, so I went to safari and tried to access the oracle em. As it turns out, because my computer is on a company network, the company's DNS doesn't know about the virtual machine, unless of course I switch to a bridged network config. However, I don't want to do that because I don't to mix up the domains. So I guess the question is, how can I define my own dns or router, or whatever it is that I need to define so that whenever I try the guest system's ip address form the host, it will use the vmnet1 or vmnet8 interface define by vmware and bypass the dns configuration of my local area network. I'd also like to know what to do incase I want to change ip addresses on the guest machine without having oracle go haywire (I've noticed a few folders on the structure which are specific for the very first IP Address)... Any help would be appreciated. Thanks in advance.

  Read the article

• How does the internet protocol handle network card numbers?

  - by Giorgio

  I know that data packets sent over the internet carry the source and destination IP address, so that the protocol can route the data to the correct destination and keep track of the source address of the packet. But what about the network card address? As far as I know, each network card has a unique identification number. Is this also transmitted with a TCP/IP packet? And when a packet is received at its destination, how is the IP address mapped to a network card number? In other words. On the sender part: does the sender store the sender network card number in the IP packets that it is sending? On the receiver part: which component maps the IP address to the receiver's network card number when a packet is received? E.g., in a home network, does the modem / router map the destination IP address of an incoming packet to a network card number and deliver the packet directly to that network card? A link to documentation on these topics would be of great help.

  Read the article

• Can't connect to FTP server from a specific location

  - by wv_pip

  Last week while uploading website files to our server via FTP, the transfer failed. Ever since then, I haven't been able to connect to the server from work. I can connect just fine from home, or by using an FTP app on my cell phone as long as I'm on the cell network. I can't access the server from any machine on my work network. It's not a credential issue, either. The error message that I always get says that a connection cannot be established, and I am never prompted for my credentials. I have changed absolutely nothing on our domain controller or our firewall/router. I've contacted our ISP (who hosts the website/FTP server) and they can't find anything wrong on their end. They insist that it must be something here at the office that is blocking access. I've also tested access to other FTP servers (ea.com, nvidia.com, etc.) so I know that port 21 is not being blocked. I'm totally stumped. Any help is much appreciated. EDIT: wireshark info here: http://www.cloudshark.org/captures/85a118ae9296?filter=ip.dst%3D%3D66.118.64.208

  Read the article

• Building a small server farm

  - by RayQuang

  Hi, I am planning to set up a Tech startup company that will provide web application solutions. Eventually we hope to diversify into different areas such as possibly social media or other services. For now we plan on running a high demand (from 1000 to 10,000 users in the first year) website running the application. This includes a MySQL database backend, email, and development servers. My question is then, what type of server arrangement will work best, that is ti say should i have a small cluster of ultra high power machines (E.G. Top of the range Xeons, with 12GB RAM) or will it be better to have more less powerful servers load balanced? Should I go for 1 - 2 u servers rack mounted ot would it be beter for it just to be tower servers for maintainability? Finally I would also like to know what kind of Internet and router i would need, I currently have 10mbit down and barely 1 mbit up, but soon our area will have a fiber optic connection with international speeds of up to 25 mbit / sec. Thanks in advance, RayQuang UPDATE: sorry I forgot to mention it, the platform that I will be using is PHP with the APC code cache, Probably running Debian.

  Read the article

< Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >