Search Results

Search found 216 results on 9 pages for 'atheros'.

Page 2/9 | < Previous Page | 1 2 3 4 5 6 7 8 9  | Next Page >

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• Atheros AR8132 Ethernet refuses to connect after suspend

  - by Ramesh Patel

  I'm having an issue where my ethernet card (Atheros Communications Inc. AR8132 Fast Ethernet (rev c0)) refuses to recognize when a network cable is plugged in after a suspend. This is dmesg after suspending: [135897.712049] atl1c 0000:02:00.0: MAC state machine can't be idle since disabled for 10ms second [135897.743729] ADDRCONF(NETDEV_UP): eth0: link is not ready [135898.541804] ADDRCONF(NETDEV_UP): eth1: link is not ready [135900.452077] atl1c 0000:02:00.0: irq 47 for MSI/MSI-X [135900.672262] atl1c 0000:02:00.0: Error get phy ID [135900.673060] ADDRCONF(NETDEV_UP): eth0: link is not ready [135900.674140] ADDRCONF(NETDEV_UP): eth0: link is not ready [135925.604052] [135935.776051] eth1: no IPv6 routers present eth0 is the ethernet card and eth1 is the wlan card (Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)). The ethernet card uses the atl1c driver and the wlan card uses the wl driver. Sorry, should have mentioned as well, running Ubuntu 12.04 with kernel 3.2.0-25-generic.

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• atheros ar8161 not recognized

  - by Paul

  Apparently I am not the only one with this problem. This was my solution, but it did not work, of course. I downloaded the tar from another computer. I found the file of the atheros driver that I needed which is apparently atl1c. I put that file on my ubuntu desktop. I ran the following in the terminal: cd ~/Desktop atl1c make sudo make install I am sure that some of you will find this code laughable, but isn't there a simple code I could use once I have the atl1c folder on the desktop?

  Read the article

• Cannot connect to a Wifi network chipset AR9287

  - by Fritz

  After updating my newly installed ubuntu 10.10. I can't connect to the wifi network anymore although it is showing it. Tried to install manufacturer driver INF file via ndiswrapper only makes things worst - lost my wifi. Downloaded and installed the compat-wireless driver for the Atheros AR9287. After installing, i got my wifi connection again but after rebooting I can't reconnect again. The Wifi access point is showing 2/5 to 3/5 signal strength. Laptop: Acer Aspire 4741G Wifi Adapter: Atheros AR9287 OS: Ubuntu 10.10 64bit

  Read the article

• Atheros AR928X wireless connection makes neighbourhood machine drop off line

  - by funicorn

  I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

  Read the article

• Frequent disconnects with oneiric server using wlan AR9285

  - by John Neil

  I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

  Read the article

• Can't connect to or see my wifi ssid

  - by ant

  Today I installed ubuntu 12.04 on my laptop. I am unable to see my home SSID or even connect to it. I've tried to connect as a hidden SSID but I always get prompted for authorization although my key is correct. I'm in in Europe but my laptop is from US. I'm not sure if that is relevant. I've read around this site and saw something that has to do with setting the channel above 11. I'm not sure I did that correctly I did this : How to use Wi-Fi channels above 11? Did't help. I'm able to connect with cable but not via wifi either windows or linux. Other devices in my home can connect without any issues, even the kindle. Here is the screenshot from my router : Here is some additional info : lspci | grep -i network 08:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) lspci -nnk | grep -A2 0280 08:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Hewlett-Packard Company U98Z062.10 802.11bgn Wireless Half-size Mini PCIe Card [103c:303f] Kernel driver in use: ath9k m-tool NetworkManager Tool State: connected (global) Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: disconnected Default: no HW Address: 90:4C:E5:38:79:0D Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes I'm not sure what to do next. Any suggestions?

  Read the article

• Frequent disconnects using wlan AR9285

  - by John Neil

  I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

  Read the article

• AR242x / AR542x wireless card not working

  - by Pipan87

  My wifi worked perfect until I updated to the latest version of Ubuntu. Now I don't find any wireless connections at all. I have tried lots of guides on the internet but I can't get it to work. I did however start to work once after writing something I don't remember in Terminal, but after rebooting it stopped working again. Some info (don't know if you need more to help): 01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: Acer Incorporated [ALI] Device 022c Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at 55200000 (64-bit, non-prefetchable) [size=256K] I/O ports at 3000 [size=128] Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [180] Device Serial Number ff-93-2e-de-00-23-8b-ff Kernel driver in use: ATL1E Kernel modules: atl1e 02:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Foxconn International, Inc. Device e00d Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at 54100000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath5k Kernel modules: ath5k

  Read the article

• Very very slow transfer speeds between Windows 7 and samba server running on Ubuntu 11.10/12.04 minimal

  - by kuzyt

  As mentioned in the title I tried transferring files between Windows 7 and the samba server running on both Ubuntu 11.10 and 12.04 but both showed very slow transfer speeds. Can someone please guide me in the right direction to debug this problem ? wget --output-document=/dev/null http://tokyo1.linode.com/100MB-tokyo.bin --2012-08-21 22:02:17-- http://tokyo1.linode.com/100MB-tokyo.bin Resolving tokyo1.linode.com (tokyo1.linode.com)... 106.187.33.12 Connecting to tokyo1.linode.com (tokyo1.linode.com)|106.187.33.12|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 104857600 (100M) [application/octet-stream] Saving to: `/dev/null' 8% [=============> ] 8,923,980 64.8K/s eta 15m 0s wlan0 IEEE 802.11abgn ESSID:"TNET" Mode:Managed Frequency:2.462 GHz Access Point: 58:6D:8F:26:20:7A Bit Rate=117 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=57/70 Signal level=-53 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:101 Invalid misc:2448 Missed beacon:0 03:00.0 Network controller: Atheros Communications Inc. AR9300 Wireless LAN adaptor (rev 01) Subsystem: Atheros Communications Inc. Device 3112 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fea00000 (64-bit, non-prefetchable) [size=128K] Expansion ROM at fea20000 [disabled] [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/4 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- Capabilities: [300 v1] Device Serial Number 00-00-00-00-00-00-00-00 Kernel driver in use: ath9k Kernel modules: ath9k

  Read the article

• Wifi too slow on 11.10/12.04

  - by Jorge Pinho

  As the title above mentions, i've some issues with wireless connection on both ubuntu 11.10 and 12.04. I've installed the latest drivers (Atheros AR928x), like "compact-wireless package" on several machines including ubuntu 11.10. The connection still too slow. My internet connection is 100 mb so, using WLAN connection, it should give me 70/80 mb of signal... instead of the 40/50 mb that i'm experience right now.. Do you have a solution to increase the signal?

  Read the article

• How to get wireless (Alfa) operate in full power and speed up wireless Internet?

  - by MahboobeAlam

  I am using Wireless to connect to the internet (router). My laptop has Atheros wireless (AR 242x/542x) adapter but the router is a little bit far-away from my room so I have to use an external wireless adapter i.e. Alfa (Realtek 8187) for connectivity. However, since I have started using Ubuntu I noticed that Alfa is not working in full power, internet speed in Ubuntu is much slower than in Windows on my laptop. When I am using Windows 7 the LED (bulb) on Alfa blinks as it should, but when in Ubuntu, it doesn't blink rather it is on but very dim. Connection using Atheros adapter is also the same (slow)... I have tried 4 methods (I found on the Internet) to troubleshoot this matter but no success. It seems to me that Ubuntu/Linux is not letting these wireless adapters to operate in full strength. iwconfig shows that power management is off for both. So what's the problem? Details: ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:16:1e:36:ec UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1657 errors:0 dropped:0 overruns:0 frame:0 TX packets:1657 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:241697 (241.6 KB) TX bytes:241697 (241.6 KB) wlan0 Link encap:Ethernet HWaddr 00:22:5f:9b:24:b5 inet6 addr: fe80::222:5fff:fe9b:24b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:715460 errors:0 dropped:0 overruns:0 frame:0 TX packets:694246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:493539292 (493.5 MB) TX bytes:235159393 (235.1 MB) wlan1 Link encap:Ethernet HWaddr 00:c0:ca:42:14:62 inet addr:192.168.100.102 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::2c0:caff:fe42:1462/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:171053 errors:0 dropped:0 overruns:0 frame:0 TX packets:181363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:74094659 (74.0 MB) TX bytes:59474204 (59.4 MB) iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off wlan1 IEEE 802.11bg ESSID:"Zia" Mode:Managed Frequency:2.412 GHz Access Point: 00:0D:F0:9C:A6:18 Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-31 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:204 Invalid misc:6610 Missed beacon:0

  Read the article

• Wireless internet works on W7 and on University Network but is extremely slow at home

  - by Rick

  I'm using ubuntu 12.04 with an Atheros wireless card. My internet speed in W7 is great. My internet speed in Ubuntu 12.04 at a university network is great. My internet speed in Ubuntu 12.04 at my home network is really slow. Some solutions I have tried but didn't work: Disabling IPv6 Running the following code: sudo ifconfig wlan0 down sudo rmmod -f iwlwifi sudo modprobe iwlwifi 11n_disable=1 sudo ifconfig wlan0 up Thanks for the help!

  Read the article

• building kernel headers (v3.4) breaks wifi (in Ubuntu 12.04.1 LTS)

  - by iphonedev7

  I have dual-booted by Samsung Series 5 Chromebook into Ubuntu using Jay Lee's script/instructions, and then installed the ~500 updates that appear thereafter. Now, I am trying to build my kernel headers in an attempt to enable virtualization so that I can run VirtualBox (I have a VM image on a flashdrive). I followed the instructions here: https://groups.google.com/forum/?fromgroups=#!topic/chromebook-central/PPQFpC7mYzk mainly doing as olofj suggests in his answer, while also making sure to abide by additions/edits made by panZ and algp. However, now that I have done so, my wifi has stopped working, and when I click on the network icon in the top bar, in place of wifi networks there is a grayed-out message that says "no network devices available". I have an Atheros AR9300 Ethernet card (I think thats what you call it). Any help is much needed and appreciated. Any further details necessary to answer the question will be provided as necessary. Thanks!

  Read the article

• Is the wireless driver from Live USB different from the standard install?

  - by Rafael Magalhães

  Linux newbie here. I've been trying to use Ubuntu (x64) as my main OS since 11.10, but my wireless connection on it has been very unstable, droping every other 5-10 mins. For this reason I see myself forced to use Windows 7 (dual booting), where connection works flawlessly -- which really bothers me. My card is an Atheros 9k, which claims a reasonable amount of wireless complaints on Ubuntu forums. I've tried every suggestion given on past questions to this site but to no avail. However, while running Ubuntu Live USB for some of the tests, I noticed that my wireless connection never failed on it and wondered if its network configuration differs from the one on the default Ubuntu install. If this is the case, how could I reproduce the Live USB network environment on my hard drive install?

  Read the article

• Update drivers for TL-WN851ND

  - by Tony_GPR

  Today I bought a new PCI wireless card, TP-Link WN851ND, with Atheros AR9227 chipset. It has 2 antennas and is compatible with Wifi N so I thought it would improve the quality of the signal. But after install it on my computer the result is the opposite to expected. It doesn't connect to my network, while my old Wifi BG card connect without problems, I created an access point from my smartphone to try the card, and work, but is very slow loading pages. In Windows 7 works perfectly, so I think the problem is the driver. I have Ubuntu 12.04 LTS with kernel 3.2.0.31, is there a way to update the driver or I can apply a patch to improve the performance of the card? Otherwise, anyone know if there is a work in progress to improve compatibility with this chipset, or is it better to change the card and buy one with better driver compatibility. And finally, which wireless N compatible chipsets have good support under Linux/Ubuntu?

  Read the article

• Wireless connects but can not connect to internet

  - by Dan

  I'm using Ubuntu 11.04 and I'm having trouble connecting to internet via wifi. Ethernet cable works though. So when I log on it auto logs on to my wifi connection at home but after about a minute or so it gives me a popup: network disabled something about .local domain and something about Avahi network (sorry if you need more on what the popup says I will reboot and look at it again). I am using Atheros wireless card. My laptop is Asus G73SW and on the forum at notebookreview.com G73SW Owner's Lounge people said they had no problem with connecting via wifi from install. Please help me because I would love to keep using this beautiful OS.

  Read the article

• No wireless after resuming from suspend?

  - by lapor

  When I resume my computer from suspend it doesn't want to connect to any wireless connection. It looks like it is connecting, but after a while it asks me to retype a password for wireless connection. It connect after I restart it. I am using Toshiba Satellite A210 and Ubuntu 10.10 (I have the same problem with 10.04 and 11.04 beta2. 14:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) Subsystem: Askey Computer Corp. Device 7128 Flags: bus master, fast devsel, latency 0, IRQ 19 Memory at cfcf0000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath5k Kernel modules: ath5k Should I file a bug?

  Read the article

• (Solved) ERROR: Packet source 'wlan0' failed to set channel 2: mac80211_setchannel() in Kismet and Ubuntu 12.10

  - by M. Cunille

  I have installed Ubuntu 12.10 in my computer with an Atheros AR5007 wireless card. I want to use Kismet but when I run it it starts displaying the message: ERROR: Packet source 'wlan0' failed to set channel X: mac80211_setchannel() It keeps displaying the same for every channel except channel 1. I have installed the compat-wireless-3.6.6-1 drivers and patched them with the following patch in order to use them with aircrack-ng. I have installed the latest version of Kismet in the git repository and I even tried with the svn but it keeps displaying the same error. I also have set the kismet.conf file with the nsource=wlan0 as it is the name of my wireless interface according to iwconfig : lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"XXXX" Mode:Managed Frequency:2.412 GHz Access Point: XX:XX:XX:XX:XX:XX Bit Rate=18 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=28/70 Signal level=-82 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:282 Missed beacon:0 I haven't found any answer since similar errors are supposed to be fixed with the latest Kismet release but this isn't my case. Any help will be appreciated. Thank you!

  Read the article

• Asus Eee PC 1000HE wireless woes

  - by Vladimir Noobokov

  Ever since I have upgraded my Asus Eee PC 1000HE from Lucid 10.04 to Precise 12.04 I have been having issues with my wireless connections. At first I had wireless dropouts: I would be able to start using wireless, but then after a few minutes the wireless would stop working even though I was still connected to the network. Lately things turned worse: while I connect to my wireless network, it just never works. I tried all sorts of solutions on offer here and in other forums but none worked. At best I got the wireless to work up until I rebooted, at which point I would get the same symptoms again: the wireless network is there, but it's not really working. By now I tried so many different "solutions" I don't know where to start describing them; I have also reinstalled 12.04 several times, enough to make me lose faith in Ubuntu. Help here looks like my last resort. For the record, my Asus Eee PC 1000HE is equipped with an Atheros wireless card. I have reinstalled 12.04, ran all the suggested updates, and receive the following response when I type iwconfig in the terminal: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Arsenal" Mode:Managed Frequency:2.452 GHz Access Point: 00:04:ED:48:67:89 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-29 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:27 Invalid misc:57 Missed beacon:0 eth0 no wireless extensions. Thanks in advance for any help that might be offered.

  Read the article

• How to install compat-drivers or compat-wireless

  - by Sasho

  Could someone please explain me in detail how to install some of this drivers. I am running Ubuntu 12.04.2 and have the infamous (as I see everywhere in the net) problem with Atheros AR9462 wifi card. I tried everything to fix it and compat drivers are the only solution that I haven't tried. I tried to install some random package from kernel.org site and it couldn't make the driver (it threw some error). Then I updated the kernel to 3.10-rc7 and downloaded the last release of compat drivers and again the same problem occured. I reinstalled Ubuntu 12.04.2 and now I am using the 3.5 kernel because I don't know if rc7 is stable version. So my question is which compat wireless or compat drivers to download for this kernel and what is the process of installing. I tried with some command from the repository and it returned that it's not found. PS I am new to Ubuntu and Linux in general so explaining at length the install process and which driver I should install would be appreciated.

  Read the article

• WIFI looses connection with AR9285 - have to disconnect / connect to regain internet?

  - by CodyLoco

  I have a G73JW laptop using Ubuntu 12.04. It has an Atheros AR9285 card. While wifi seems to work fine most of the time, about every hour or two it will loose the connection to the internet. The connection will appear to be connected still to the wireless router, but internet access is gone. Disconnecting and reconnecting to the access point solves the problem, as does disabling and reenabling the adapter via the hardware keyboard shortcut. How might this be solved so the connection is stable and doesn't drop? EDIT: It looks like the network dropping isn't related to DNS as it fails either way: codyloco@CodyLoco-Ubuntu:~$ dig askubuntu.com @8.8.8.8 ; <<>> DiG 9.8.1-P1 <<>> askubuntu.com @8.8.8.8 ;; global options: +cmd ;; connection timed out; no servers could be reached codyloco@CodyLoco-Ubuntu:~$ dig askubuntu.com ; <<>> DiG 9.8.1-P1 <<>> askubuntu.com ;; global options: +cmd ;; connection timed out; no servers could be reached Again cycling (disabling / enabling) the adapter corrects the issue.

  Read the article

• AR9485 wireless card loses ability to connect after hibernation

  - by DrewDiezel

  This has happened twice now, the first time it happened I just reinstalled Ubuntu. The only things that I've been messing with in terms of networking, have been restarting the network-manager service after I resume from hibernate (because it never works right after resume, but restarting the service fixes that), and changing my mac address with ifconfig wlan0 down && ifconfig wlan0 hw ether 11:22:33:44:55 && ifconfig wlan0 up. using tail | dmesg returns a bunch of attempts to connect, saying something like authenticating ... okay you're connected! now I'm going to just disconnect because I feel like it. (reason=3). Any ideas? If it helps maybe I'll add a picture of the tail|dmesg output later. My wireless drivers are as follows: Atheros AR9485 Wireless Network Adapter Hamachi Network Interface Microsoft Virtual Wifi Miniport Adapter Realtek PCIe GBE Family Controller VirtualBox Host-Only Ethernet Adapter Here is a pastebin of some terminal outputs that could help. Also, the reddit thread has a few answers, for anyone curious. It's located here. It is entirely possible that it's just my school wifi blocking out my laptop, and my home wifi sucks. Wifi does work at places other than my home and school, however my phone can connect to both places. Here is a pastebin of the results of the wireless-info script.

  Read the article

• Determining Maximum Txpower a WiFi Card Supports?

  - by BigGenius

  I have a Atheros R9285 wifi card. How can i determine , what is max. Txpower it can support? biggenius@hackbook:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Default" Mode:Managed Frequency:2.437 GHz Access Point: 00:08:5C:9D:4F:40 Bit Rate=2 Mb/s Tx-Power=35 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=24/70 Signal level=-86 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:140 Invalid misc:247 Missed beacon:0 eth0 no wireless extensions. biggenius@hackbook:~$ iw phy0 info Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (35.0 dBm) * 2417 MHz [2] (35.0 dBm) * 2422 MHz [3] (35.0 dBm) * 2427 MHz [4] (35.0 dBm) * 2432 MHz [5] (35.0 dBm) * 2437 MHz [6] (35.0 dBm) * 2442 MHz [7] (35.0 dBm) * 2447 MHz [8] (35.0 dBm) * 2452 MHz [9] (35.0 dBm) * 2457 MHz [10] (35.0 dBm) * 2462 MHz [11] (35.0 dBm) * 2467 MHz [12] (35.0 dBm) * 2472 MHz [13] (35.0 dBm) * 2484 MHz [14] (35.0 dBm) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 5180 MHz [36] (35.0 dBm) * 5200 MHz [40] (35.0 dBm) * 5220 MHz [44] (35.0 dBm) * 5240 MHz [48] (35.0 dBm) * 5260 MHz [52] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (35.0 dBm) * 5765 MHz [153] (35.0 dBm) * 5785 MHz [157] (35.0 dBm) * 5805 MHz [161] (35.0 dBm) * 5825 MHz [165] (35.0 dBm) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO } <= 8, total <= 2048, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (82) * Unknown command (81) * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9  | Next Page >