Search Results

Search found 216 results on 9 pages for 'atheros'.

Page 5/9 | < Previous Page | 1 2 3 4 5 6 7 8 9  | Next Page >

• Have Ubuntu auto-connect to wireless AP without logging in

  - by dragonmantank

  We have an ubuntu box set up to do some monitoring but due to the placement are unable to run CAT5 to the box itself. I have an Atheros PCI card that works great as long as someone is logged into Gnome and it doesn't disconnect from the AP during that time. Is there a way to have Ubuntu connect to the AP during boot, and always reconnect if it finds a signal from a specified AP? The box would have a static IP and only connecting to a specific AP using WEP.

  Read the article

• Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

  Read the article

• How can I find which drivers are the correct ones for my machine?

  - by tombull89

  I'm currently installing Windows 7 onto a new laptop before imaging it to deploy. I need to install the Wireless and Graphics drivers, but the HP site is offering me both ATI and Intel graphics drivers (at 102MB and 470(!)MB) a pop, as well as Intel, Broadcomm, RealTek and Atheros wireless drivers. Is there a bit of software that will tell me what devices are in the machine so I don't have to go through, trial-and-error and find which is the right driver for the hardware?

  Read the article

• Wifi Direct P2P-go and P2P-client support in ubuntu

  - by giri

  I am trying to get wifi direct working on a laptop with ubuntu 12.04 When I type the command 'iw list' it doesn't show P2P-client or P2P-go under 'supported interface modes.From http://wireless.kernel.org/en/users/Documentation/iw/replace-iwconfig I found that 'iwconfig' was replaced with 'iw'.Does it mean that my hardware doesn't have support for wifi-direct or is it just the software(drivers) issue? If is it just sofware issue please help me to find the right drivers which support wifi-direct. Here is the info about my ethernet controller from the output of 'lspci' 02:00.0 Ethernet controller: Atheros Communication Inc. AR242x / AR542x Wreless Network Adapter (PCI-Express) (rev 01) 06:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller (rev 13)

  Read the article

• Connecting 2 ubuntu machines as a LAN

  - by Brendan Cutjar

  Hi i am trying to connect 2 ubuntu computers as a LAN. In my current setup I have: One machine running ubuntu 11.10 with Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller While the other machine is running Ubuntu 12.04 with an Atheros Communications Inc AR8152 v1.1 Fast Ethernet The two machines are connected via a switch (Edimax ES-3205P). Unfortunately I still cannot connect the two machines together. Can somebody please show me what to do and how to go about solving this issue? Thank you ANSWERED All I had to do was set up both ip's maually, subnet mask to 255.255.255.0 and left blank both gateway and DNS.

  Read the article

• Acer Aspire One 722 broadcom 4313 wifi

  - by Colin Matheson

  I had an Acer Aspire One 722 with the Atheros Wifi card and it worked fine on 11.04. So we bought 200 of them for our school. However these all came with the Broadcom BCM4313 wireless card and there are issues. It is using the brcmsmac driver and they connect initially. However after a time (sometimes just a few webpages) some of them lose connection. However, they still have an IP and network-manager says they are connected, but no pages load and you can't ping anything on the LAN or internet. A disconnect/reconnect can fix it, but sometimes a restart is required. It happens frequently so is a major issue. Lots of broadcom drivers are blacklisted: bcm43xx, b43, brcm80211. Any ideas or experiences with the broadcom4313 card? Please save these computers from a Windows fate!

  Read the article

• Asus X552VL WI-FI Problem

  - by Mitkobg

  I have a problem with my Wireless on my laptop. When i did rfkill list: 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 4: hci0: Bluetooth Soft blocked: no Hard blocked: no 5: phy1: Wireless LAN Soft blocked: no Hard blocked: yes itko@Mitko:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off mitko@Mitko:~$ lspci -nnk | grep -A2 0280 03:00.0 Network controller [0280]: Qualcomm Atheros AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:2c97] Kernel driver in use: ath9k mitko@Mitko:~$ lsmod | grep -e ath9k -e asus asus_nb_wmi 16990 0 asus_wmi 24191 1 asus_nb_wmi sparse_keymap 13948 1 asus_wmi ath9k 164164 0 ath9k_common 13551 1 ath9k ath9k_hw 453856 2 ath9k_common,ath9k ath 28698 3 ath9k_common,ath9k,ath9k_hw mac80211 626557 1 ath9k cfg80211 484040 4 wl,ath,ath9k,mac80211 wmi 19177 3 mxm_wmi,nouveau,asus_wmi video 19476 3 i915,nouveau,asus_wmi

  Read the article

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

• Slow on browsing web, but normal when using apt-get

  - by Arif Setyawan

  I have a problem with my fresh instalation of Ubuntu 11.10. The problem happen when i start up my browser and accessing website such google, askubuntu.com, facebook and other sites. frustate on the situation i try watch the progress in system monitor. the result from monitor shows that there is no data transfer when i try to accessing the page. firstly, i assume that it is the trouble from my ISP or my home connection. But it is not. When i try pinging google it shows transaction between my computer and the network but still null from browser. Then i tried to test the aptitude and it was work fine but still the browser won't recieve any packet from the internet. Here is the detail of my tools : Laptop : Toshiba Satellite e205 (network card atheros) Operating System : Ubuntu 11.04 dual booted with Win7 Browser : Mozilla Firefox comes up with the Ubuntu 11.10 installation Chrome : Last version (just yesterday install it) Thank You before :) [this question posted via win]

  Read the article

• Connectify like functionality on Ubuntu running on T61 - wifi 4965 AGN

  - by Vivek Sharma

  I would like to use my laptop as an Access point, so that i can connect my phones through Wifi. I have done this my office laptop T410. I am having T61 with wifi module 4965. Connectify on windows does not support it. I am following -- https://help.ubuntu.com/community/WifiDocs/WirelessAccessPoint to make achieve WAP capability on my T61 running ubuntu 10.10. The link says something about "master mode", how do i put my T61 wifi-inter4965 in master mode. Can i install madwifi or atheros drivers on it. I am using galaxy S froyo, and it does not support Ad-hoc network. Has anyone tired to achieve this.

  Read the article

• Kubuntu 12.04 Won't let me search for wireless network

  - by Bora George

  Hello I'm running a brand new Kubuntu 12.04 single boot on my laptop, this is the first time I tried connecting to a wireless network. I tried using the network manager app allready on the task bar, but it doesn't let me tick the column to search for wireless networks, i.e. it will untick it automaticaly, it's dissabled by the software or the hardware, but I doubt it. I've tried searching the other questions on this site, and I can't see anything which helps with my problem. I know my wireless card is a Atheros AR9285, I don't think I installed any firmware for it, I'm sorry I can't offer more info but I'm completely new to networking and all that I have for the network to connect to are it's name and password of course.

  Read the article

• Wireless not connecting on Ubuntu 13.10, Toshiba Satellite pro L 650

  - by user204842

  I have just installed Ubuntu 13.10 on my Toshiba Satellite Pro L650. After several reboots, installing/ uninstalling the broadcom driver I still can't connect. It detects the wi fi signals and the icon flashes as if it's trying to connect but never actually does. I'm really quite rubbish with code and stuff, but I really like Ubuntu as an OS and would really appreciate any suggestions anyone can offer! 02:00.0 Ethernet controller: Qualcomm Atheros AR8151 v1.0 Gigabit Ethernet (rev c0) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)

  Read the article

• "Operating system not found" after upgrading to 13.10

  - by Hongbo Zhu

  I own a Thinkpad X121e and I upgraded its Ubuntu from 13.04 64bit to 13.10 64bit using the Update Manager. When the upgrade process suggested to restart the system, I restarted the computer and now it says "Operating system not found" after a very brief splash screen. The splash screen says something like (too brief to see everything): Intel UNDI, PXE-2.0 ... For Atheros ethernet Controller ... Check cable connection! PXE-MOF: Exiting INTEL PXE ROM I prepared a startup USB disk using Ubuntu 13.10. I tried the startup USB and it works very well on other computers. So I changed the booting order of X121e and tried all three USB slots, all said "Operating System not found" without any splash screen. I also tried using startup USB with 12.04 LTS. Same results. I do not really want to reinstall the system now. Any hints on how to proceed?

  Read the article

• Wireless always disconnect

  - by Silas

  I upgraded my Ubuntu 10.10 for Ubuntu 12.04. I have a Emachines E625 With Ubuntu 12.04 my wireless always disconnects every 10 sec. It didn't do that with 10.10. Here is my config: Linux sylvain-eMachines-E625 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:54:40 UTC 2012 i686 athlon i386 GNU/Linux total used free shared buffers cached Mem: 1759 1425 333 0 46 925 -/+ buffers/cache: 452 1306 Swap: 1788 0 1788 02:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 05:00.0 Ethernet controller: Atheros Communications Inc. AR8132 Fast Ethernet (rev c0) I will really enjoy an answer to solve this problem. Thank you in advance! Silas

  Read the article

• Connectify-like functionality on 4965 AGN wireless?

  - by Vivek Sharma

  I would like to use my laptop as an Access point, so that i can connect my phones through Wifi. I have done this my office laptop T410. I am having T61 with wifi module 4965. Connectify on windows does not support it. I am following these instructions to make achieve WAP capability on my T61 running ubuntu 10.10. The link says something about "master mode", how do i put my T61 wifi-inter4965 in master mode. Can I install madwifi or atheros drivers on it? I am using galaxy S froyo, and it does not support Ad-hoc network. Has anyone tried to achieve this?

  Read the article

• Trouble installing 12.04 from cd, blank screen with cursor

  - by Master Morality

  I should preface this with saying that this is not my first rodeo. I started playing with Linux in 1999 (Red Hat) and I'm currently typing this on a ThinkPad running 12.04... When I put in the live cd, I boots, and I can get to the option menu to decide whether to install/run etc, but at any point beyond that I get only a single caret. I can type stuff in, but it goes no where. I've tried the usual stuff like running with nomodeset (thinking it was the intel HD400 graphics, but it is integrated graphics...) here is the setup: ASUS p8z77 pro (with the Atheros AR9485 wifi supposedly, but I'm not that far yet) i7 3370k 8gig X 2 G.Skill Crucial M4 (256 gig) LG Super-multi DVD re-writer no video card UPDATE: I though may be it was a bad image on the CD, so I downloaded another iso, and used a USB disk. now it boots to a blank screen. I can see the "press any key to get options" screen, but after that, it just goes to a blank screen.

  Read the article

• No Internet Connection - ubuntu 11.10

  - by emersonhsieh

  I installed Ubuntu 11.10 recently. After the first bootup the computer freezes so I have to force-quit my computer. Then I turned on my computer after that. I tried connecting to the internet. My (and my neighbor's) wireless networks shown up, but no matter how many times I tried, I can't connect to my home network. I checked the password and the other laptop's internet works (a MacBookPro). It was a wireless network. What's weird is that the Wireless network worked when I was installing ubuntu How can I connect to the internet now? I don't have a wired network. Please Help! Any help will be appreciated Specs: ASUS F81Se, Windows 7 Dual-boot, I remember the wireless card was made by Atheros, 4GB RAM

  Read the article

• Issues running alongside windows and connecting to wireless network

  - by user292247

  Okay so I'm trying to get started with ubuntu but I'm encountering a couple problems: When I boot up the CD and try to install, it does not recognize that I have windows 7 installed and just sees it as unallocated space so the only way I've been able to install it is by wiping the drive which was fine, but it'd be nice to be able to boot either. And secondly, I cannot figure out how to get wireless working. When I try to connect on the initial installation process it tells me to connect to my adapter and just asks for a password. I suspect it could be a driver issue but I wouldn't know where to find it. I have an AR9485 atheros adapter and am attempting to run ubuntu 14.04. Thanks

  Read the article

• Microphone not capturing sound on 12.04 Lenovo G580

  - by Yam Marcovic

  In both Skype and the Sound Recorder application, I am not capturing any audio from my built-in microphone. I'm not sure why. Otherwise, sound output is working well. I have tried running gstreamer-properties and setting the Default Input plugin to PulseAUdio as well (to match the output), and it didn't help. I have tried running alsamixer -V all and I only get 2 input-related entries: Capture(L R) which is on 100 and not muted (can't be either), and Analog Mic Boost which is on 20db. Extra info: Camera (video) is working well on Skype and Kamerka. Can you please help me get my microphone to work? lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) (prog-if 00 [VGA controller]) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 42 Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at 3000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) (prog-if 30 [XHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 41 Region 0: Memory at e0600000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 43 Region 0: Memory at e0614000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at e0619000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 44 Region 0: Memory at e0610000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: e0500000-e05fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: e0400000-e04fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at e0618000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 40 Region 0: I/O ports at 3088 [size=8] Region 1: I/O ports at 3094 [size=4] Region 2: I/O ports at 3080 [size=8] Region 3: I/O ports at 3090 [size=4] Region 4: I/O ports at 3060 [size=32] Region 5: Memory at e0617000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 10 Region 0: Memory at e0615000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 3040 [size=32] Kernel modules: i2c-i801 01:00.0 Ethernet controller: Atheros Communications Inc. AR8162 Fast Ethernet (rev 08) Subsystem: Lenovo Device 3979 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0500000 (64-bit, non-prefetchable) [size=256K] Region 2: I/O ports at 2000 [size=128] Capabilities: <access denied> 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Lenovo Device 31a1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at e0400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath9k Kernel modules: ath9k aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: CONEXANT Analog [CONEXANT Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0

  Read the article

• Wireless networks are not detected at start up in Ubuntu 12.04

  - by Kanhaiya Mishra

  I have recently (three four days ago) installed Ubuntu 12.04 via windows installer i.e. wubi.exe. After the installation completed wireless and Ethernet were both working well. But after restart wireless networks didn't show up while in the network manager both networking and wireless were enabled. Though sometimes after boot it did show the networks available but very rarely. So I went through various posts regarding wireless issues in Ubuntu 12.04 and tried so many things but ended up in nothing satisfactory. I have Broadcom 4313 LAN network controller and brcmsmac driver. Then relying on some suggestions I tried to install bcm-wl driver but couldn't install due to some error in jockeyl.log file. Then i tried fresh installation of the same driver but still could resolve the startup issues with wireless. Then again I reinstalled Ubuntu inside windows using wubi installer. This time again same problem occurred after boot. But this time I successfully installed wl driver before disturbing file-system files of Ubuntu. But again the same issue. This time I noticed some new things: If I inserted Ethernet/LAN cable before startup then wireless networks are available and of course LAN(wired) networks also work. but if i don't plug in cable before startup and then plug it after startup then it didn't detect Ethernet network neither wireless. So I haven't noticed it before that LAN along with wifi also doesn't work after startup. But if i suspend the session and make it sleep and again login then it worked. I tried it every time that WLAN worked perfectly. But still i m unable to resolve that startup problem. Each time i boot first I have to suspend it once then only networks are available. It irritates me each time i reboot/boot my lappy. So please help out of this problem. Any ideas/help regarding this issue would be highly appreciated. Some of the commands that i run gave following results: # lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) # sudo lshw -C network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:49:b6:ab width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.1.7 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: b8:ac:6f:6b:f7:4a capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) # lsmod | grep wl wl 2568210 0 lib80211 14381 2 lib80211_crypt_tkip,wl # sudo iwlist eth1 scanning eth1 Scan completed : Cell 01 - Address: 30:46:9A:85:DA:9A ESSID:"BH DASHIR 2" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:4/5 Signal level:-60 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B000103104700109AFE7D908F8E2D381860668BA2E8D8771021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: C0:3F:0E:EB:45:14 ESSID:"BH DASHIR 3" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-71 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B00010310470010F3C9BBE499D140540F530E7EBEDE2F671021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 03 - Address: A0:21:B7:A8:2F:C0 ESSID:"BH DASHIR 4" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:1/5 Signal level:-86 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD8B0050F204104A0001101044000102103B0001031047001000000000000010000000A021B7A82FC01021000D4E6574676561722C20496E632E10230009574E523130303076321024000456324831104200046E6F6E651054000800060050F20400011011001B574E5231303030763228576972656C6573732041502D322E344729100800020086103C000103 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s

  Read the article

• Ubuntu 12.04 wireless (wifi) not working, can not upgrade to 12.10, touchpad gestures not working. What to do?

  - by Ritwik

  I installed ubuntu 12.04 LTS 3 days ago and since then wireless feature and touchpad gestures are not working. Tried everything on internet but still unsuccessful. I cant upgrade to ubuntu 12.10. These are the following comments I tried. Please help me. EDIT: just realized usb 3.0 is also not working. COMMAND lsb_release -r OUTPUT ----------------------------------------------------------------- Release: 12.04 ----------------------------------------------------------------- COMMAND lspci OUTPUT ------------------------------------------------------------------ 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) 00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5) 00:1c.1 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 (rev d5) 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5) 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05) 07:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M / GT 620M/625M/630M/720M] (rev a1) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 07) 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01) 0f:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01) ------------------------------------------------------------------ COMMAND sudo apt-get install linux-backports-modules-wireless-lucid-generic OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-backports-modules-wireless-lucid-generic ------------------------------------------------------------------- COMMAND cat /etc/lsb-release; uname -a OUTPUT ------------------------------------------------------------------- DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.5 LTS" Linux ritwik-PC 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ------------------------------------------------------------------- COMMAND lspci -nnk | grep -iA2 net OUTPUT ------------------------------------------------------------------- 08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 07) Subsystem: Hewlett-Packard Company Device [103c:225d] Kernel driver in use: r8169 -- 0f:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Hewlett-Packard Company Device [103c:217f] ------------------------------------------------------------------- COMMAND lsusb OUTPUT ------------------------------------------------------------------- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:8008 Intel Corp. Bus 002 Device 002: ID 8087:8000 Intel Corp. ------------------------------------------------------------------- COMMAND iwconfig OUTPUT ------------------------------------------------------------------- lo no wireless extensions. eth0 no wireless extensions. ------------------------------------------------------------------- COMMAND rfkill list all OUTPUT ------------------------------------------------------------------- 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no ------------------------------------------------------------------- COMMAND lsmod OUTPUT ------------------------------------------------------------------- Module Size Used by snd_hda_codec_realtek 224215 1 bnep 18281 2 rfcomm 47604 0 bluetooth 180113 10 bnep,rfcomm parport_pc 32866 0 ppdev 17113 0 nls_iso8859_1 12713 1 nls_cp437 16991 1 vfat 17585 1 fat 61512 1 vfat snd_hda_intel 33719 3 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event nouveau 775039 0 joydev 17693 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq ttm 76949 1 nouveau uvcvideo 72627 0 snd 79041 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device videodev 98259 1 uvcvideo drm_kms_helper 46978 1 nouveau psmouse 98051 0 drm 241971 3 nouveau,ttm,drm_kms_helper i2c_algo_bit 13423 1 nouveau soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm v4l2_compat_ioctl32 17128 1 videodev hp_wmi 18092 0 serio_raw 13211 0 sparse_keymap 13890 1 hp_wmi mxm_wmi 13021 1 nouveau video 19651 1 nouveau wmi 19256 2 hp_wmi,mxm_wmi mac_hid 13253 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62190 0 ------------------------------------------------------------------- COMMAND sudo su modprobe -v ath9k OUTPUT ------------------------------------------------------------------- insmod /lib/modules/3.2.0-67-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko insmod /lib/modules/3.2.0-67-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko ------------------------------------------------------------------- COMMAND do-release-upgrade OUTPUT ------------------------------------------------------------------- Err Upgrade tool signature 404 Not Found [IP: 91.189.88.149 80] Err Upgrade tool 404 Not Found [IP: 91.189.88.149 80] Fetched 0 B in 0s (0 B/s) WARNING:root:file 'quantal.tar.gz.gpg' missing Failed to fetch Fetching the upgrade failed. There may be a network problem. ------------------------------------------------------------------- COMMAND sudo modprobe ath9k dmesg | grep ath9k NO OUTPUT FOR THEM COMMAND dmesg | grep -e ath -e 80211 OUTPUT ------------------------------------------------------------------- [ 13.232372] type=1400 audit(1408867538.399:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=975 comm="apparmor_parser" [ 13.232615] type=1400 audit(1408867538.399:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=975 comm="apparmor_parser" [ 15.186599] ath3k: probe of 3-4:1.0 failed with error -110 [ 15.186635] usbcore: registered new interface driver ath3k [ 88.219329] cfg80211: Calling CRDA to update world regulatory domain [ 88.351665] cfg80211: World regulatory domain updated: [ 88.351667] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 88.351670] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351671] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351673] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351674] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351675] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) ------------------------------------------------------------------- COMMAND sudo apt-get install touchpad-indicator OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: gir1.2-gconf-2.0 python-pyudev Suggested packages: python-qt4 python-pyside.qtcore The following NEW packages will be installed: gir1.2-gconf-2.0 python-pyudev touchpad-indicator 0 upgraded, 3 newly installed, 0 to remove and 0 not upgraded. Need to get 84.1 kB of archives. After this operation, 1,136 kB of additional disk space will be used. Do you want to continue [Y/n]? Y Get:1 http://ppa.launchpad.net/atareao/atareao/ubuntu/ precise/main touchpad-indicator all 0.9.3.12-1ubuntu1 [46.5 kB] Get:2 http://archive.ubuntu.com/ubuntu/ precise/main gir1.2-gconf-2.0 amd64 3.2.5-0ubuntu2 [7,098 B] Get:3 http://archive.ubuntu.com/ubuntu/ precise/main python-pyudev all 0.13-1 [30.5 kB] Fetched 84.1 kB in 2s (31.6 kB/s) Selecting previously unselected package gir1.2-gconf-2.0. (Reading database ... 169322 files and directories currently installed.) Unpacking gir1.2-gconf-2.0 (from .../gir1.2-gconf-2.0_3.2.5-0ubuntu2_amd64.deb) ... Selecting previously unselected package python-pyudev. Unpacking python-pyudev (from .../python-pyudev_0.13-1_all.deb) ... Selecting previously unselected package touchpad-indicator. Unpacking touchpad-indicator (from .../touchpad-indicator_0.9.3.12-1ubuntu1_all.deb) ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for software-center ... INFO:softwarecenter.db.update:no translation information in database needed Setting up gir1.2-gconf-2.0 (3.2.5-0ubuntu2) ... Setting up python-pyudev (0.13-1) ... Setting up touchpad-indicator (0.9.3.12-1ubuntu1) ... ------------------------------------------------------------------- Not able to find ( drivers/net/wireless/ath/ath9k/hw.c ) or ( drivers/net/wireless/ath/ath9k/hw.h )

  Read the article

• ndiswrapper wlan driver installed, but wlan still does not work

  - by mugetsu

  I'm trying to get my Atheros AR1111 EB-WG PCI wireless adapter to work. Right now wifi is not even detected. I'm on ubuntu 12.04 64bit and I managed to find a xp64bit driver. I followed the exact steps here: https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper And where I do ndiswrapper -l I get something like : {name of driver} : driver installed device ({Chipset ID}) present which shows that the driver installed properly However, after I load the new module : sudo modprobe ndiswrapper nothing happens, and iwconfig shows that I still have no wlan. I tried to do dmseg | grep ndiswrapper, but there were no driver loading errors or anything strange. I also have blacklist ath5k, ath8k in /etc/modprobe.d/blacklist.conf What am I doing wrong? What could be causing this?

  Read the article

• Basic networking problem with Ubuntu 9.04 on Acer Extensa 5635Z laptop

  - by sapporo

  I just installed Ubuntu 9.04 on a brand new Acer Extensa 5635Z laptop, but ethernet networking does't work (wireless doesn't work either, but I'd be happy with ethernet for now). eth0 isn't listed in /etc/network/interfaces: $ cat /etc/network/interfaces auto lo iface lo inet loopback lshw does show the nic, but I can't make much sense out of the information: $ sudo lshw -class network -sanitize *-network DISABLED description: Wireless interface product: AR928X Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:07:00.0 logical name: wmaster0 version: 01 serial: [REMOVED] width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath9k latency=0 module=ath9k multicast=yes wireless=IEEE 802.11bgn *-network UNCLAIMED description: Ethernet controller product: Attansic Technology Corp. vendor: Attansic Technology Corp. physical id: 0 bus info: pci@0000:09:00.0 version: c0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list configuration: latency=0 *-network DISABLED description: Ethernet interface physical id: 1 logical name: pan0 serial: [REMOVED] capabilities: ethernet physical configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes Thanks for your help!

  Read the article

• Acer Aspire 3680 Wireless Signal Problem

  - by SHiNKiROU

  I am using Acer Aspire 3680. I recently reinstalled Windows Vista, and the wireless did not work by default. I installed the "Atheros Wireless LAN Driver" on this site: http://support.acer-euro.com/drivers/notebook/as_3680.html The result, the wireless APs are successfully scanned. However, when I tried to join a network, even with 5/5 signal, an error message showed up diagnosing signal too little. I restarted as Ubuntu, and wireless worked perfectly, with same computer position. Even more confusing, When I moved to the kitchen (2 meters close to the router), the wireless connected, when I move back to my room, wireless failed on Vista and worked on Ubuntu. It is clearly the driver problem. Acer laptops seems come with pre-installed drivers, but after re-installation, they are all gone. (I can't find the original Acer backup disc) Please do not answer "move closer to the AP" and something related to "interference", as wireless worked with Ubuntu's default driver.

  Read the article

• Windows 2012 Server Hyper-V: Cannot see LAN

  - by Samuel

  I have one NIC on the machine loaded XP on the Hyper-V and had chosen the network as virtual switch. No LAN and no internet shows up on the client. Am I missing something? it used to work in 2008-R2. Details: One network card on machine (Qualcomm Atheros AR8131 PIC-E Gigabit Ethernet controller) The virtual machine hard disk is pointing to and existing XP-SP2 hard disk created using VPC 2007 The Virtual machine Network Adapter is setup as Virtual Switch to the real ethernet controller with Enable virtual LAN identification set to 2 (no other virtual machine is created in the system) After the virtual machine boots LAN shows empty in Control Panel Network Connections (this is XP client) and I also cannot access the internet. XP is showing activation prompt but as far as I know it should not disable the network! Virtual network switch is set to External

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9  | Next Page >