Search Results

Search found 2364 results on 95 pages for 'cisco san'.

Page 2/95 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Cisco VPN stops Windows 7 Browsing

  - by Sharjeel Sayed

  My browsing and other 'internet' activity (dropbox,digsby etc) halts when I connect to my office VPN using Cisco Systems VPN client Version 5.0.04.0300 on my Windows 7 Ultimate.The only option left for me at this time is to use my office proxy to enable the connection back. I tried doing the ucheck "Use default gateway on remote network" solution as mentioned on a previous post Windows 7 VPN stops web browser but I don't see that option on the properties of "Cisco systems VPN adapter" connection properties. Here is the screenshot

  Read the article

• Configure spanning tree from HP to Cisco hardware

  - by Tim Brigham

  I have three switches I'd like to configure in a loop - a Cisco stack (3750s) and two HP 2900 series. Each is connected to the next with a 10 gig backplane of one form or another. How do I configure the spanning tree on these systems to make this function correctly? From the documents I've looked at it looks like I need to set both sets of hardware to use MST mode but I'm not sure past that point. The trunking, etc is all set up as needed. HP Switch 1 A4 connected to Cisco 1/0/1. HP Switch 2 B2 connected to Cisco 2/0/1. HP Switch 1 A2 connected to HP Switch 2 A1. HP Switch 1 show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 1-4094 Switch MAC Address : 0021f7-126580 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 352,485 Time Since Last Change : 2 secs CST Root MAC Address : 0018ba-c74268 CST Root Priority : 1 CST Root Path Cost : 200000 CST Root Port : 1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- ... A1 | Auto 128 Disabled | A2 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A3 10GbE-CX4 | Auto 128 Disabled | A4 10GbE-SR | 2000 128 Forwarding | 0021f7-126580 2 Yes No HP Switch 2 show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 1-4094 Switch MAC Address : 0024a8-cd6000 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 19,623 Time Since Last Change : 32 secs CST Root MAC Address : 0018ba-c74268 CST Root Priority : 1 CST Root Path Cost : 202000 CST Root Port : A1 IST Regional Root MAC Address : 0024a8-cd6000 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- ... A1 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A2 10GbE-CX4 | Auto 128 Disabled | B1 SFP+SR | 2000 128 Blocking | a44c11-a67c80 2 Yes No B2 | Auto 128 Disabled | Cisco Stack 1 show spanning-tree ... (additional VLANs) VLAN0100 Spanning tree enabled protocol ieee Root ID Priority 1 Address 0018.bac7.426e Cost 2 Port 107 (TenGigabitEthernet2/1/1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32868 (priority 32768 sys-id-ext 100) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Desg FWD 2 128.53 P2p Te2/1/1 Root FWD 2 128.107 P2p

  Read the article

• Cisco ASA Act as a Hardware Security Module?

  - by Derek

  Hello, We have a partner that is requiring us to get a HSM for a web application that we host for them. This is something new for us, we've always installed our SSL certificates on our web servers and never needed a hardware device. We currently have 2 Cisco ASA 5510 firewalls in an active/standby configuration. Both ASAs have a ASA-SSM-10 security module installed in them. The web application is a standard HTTPS webpage with no authentication required. I was wondering if we could use our Cisco ASAs to meet this requirement or if we'll have to buy another device. I was doing some searching and read about Cisco's clientless webvpn feature. It sounds like it might work, but I'm not sure. We basically want the ASA to handle the SSL and proxy the connection to our web servers. We do not want to prompt for a username or password to connect or show any portals, just display the web page. If the ASA cannot do this, does any one have any recommendations for network attached hardware security modules? We are using VMware vCenter, so we'd rather have an external device attached to the network, rather than buying HSM cards for every ESXi host. Thanks, Derek

  Read the article

• How to allow local LAN access while connected to Cisco VPN?

  - by Ian Boyd

  How can I maintain local LAN access while connected to Cisco VPN? When connecting using Cisco VPN, the server has to ability to instruct the client to prevent local LAN access. Assuming this server-side option cannot be turned off, how can allow local LAN access while connected with a Cisco VPN client? I used to think it was simply a matter of routes being added that capture LAN traffic with a higher metric, for example: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.255.0.0 10.0.0.3 10.0.0.3 20 <--Local LAN 10.0.0.0 255.255.0.0 192.168.199.1 192.168.199.12 1 <--VPN Link And trying to delete the 10.0.x.x -> 192.168.199.12 route don't have any effect: >route delete 10.0.0.0 >route delete 10.0.0.0 mask 255.255.0.0 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 if 192.168.199.12 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 if 0x3 And while it still might simply be a routing issue, attempts to add or delete routes fail. At what level is Cisco VPN client driver doing what in the networking stack that takes overrides a local administrator's ability to administer their machine? The Cisco VPN client cannot be employing magic. It's still software running on my computer. What mechanism is it using to interfere with my machine's network? What happens when an IP/ICMP packet arrives on the network? Where in the networking stack is the packet getting eaten? See also No internet connection with Cisco VPN Cisco VPN Client interrupts connectivity to my LDAP server Cisco VPN stops Windows 7 Browsing How can I prohibit the creation of a route in Windows XP upon connection to Cisco VPN? Rerouting local LAN and Internet traffic when in VPN VPN Client "Allow local LAN Access" Allow Local LAN Access for VPN Clients on the VPN 3000 Concentrator Configuration Example LAN access gone when I connect to VPN Windows XP Documentation: Route Edit: Things I've not yet tried: >route delete 10.0.* Update: Since Cisco has abandoned their old client, in favor of AnyConnect (HTTP SSL based VPN), this question, unsolved, can be left as a relic of history. Going forward, we can try to solve the same problem with their new client.

  Read the article

• iPad connections to Cisco VPN error -- "Enter your user authentication"

  - by rhart

  Is anyone else having problems with the iPad IPSec (Cisco) VPN configuration? I've configured a Cisco VPN connection to a PIX 501 firewall on a 32GB Wifi Apple iPad. This is done in Settings - General - Network - VPN - Add VPN Configuration - IPSec tab. When everything is set up properly and I attempt to connect I just get a popup that says "Enter your user authentication" with no fields to enter either piece of info, and just OK and Cancel buttons. I've read about similar problems with the VPN client built into Mac OS X and the iPhone 3GS but never with the iPad. Does anybody know a solution? I'm not afraid to change the configuration of my PIX 501 if that's necessary.

  Read the article

• Cisco ASA bonding/teaming/port-channel capabilities

  - by Antoine Benkemoun

  Hello, This seemed to me like a really simple question that I would be able to answer by myself but I have not been able to find any info on this subject. I have a Cisco ASA 5510 which has 4 FastEthernet interfaces. I was wondering if it would be possible to use 2 or 3 of these interfaces as a port-channel in order to agregate bandwidth for multiple VLANs. I have found no info on the Cisco website nor on Google. Is this just a stupid/crazy idea or am I missing something ? Thank you in advance for your help, Antoine

  Read the article

• Cisco 877 as a VPN server?

  - by Massimo

  I have a Cisco 877 router which connects my network to the Internet using an ADSL line, a single public IP address and NAT; the IOS version is 15. Everything is working ok, but I'd like to configure this router to be a VPN server, to be able to connect to the network from the outside. I've tried looking for documentation, but everything I can find is related to having the 877 act as a VPN client, or to site-to-site VPNs; I can't find anything about letting single remote computers access the internal network, which is something I can do quite easily using Windows' RRAS or ISA Server. Can the Cisco 877 act as a VPN server for remote client computers? (Looks like it should, but just to be sure...) Which type of VPNs does it support? Do they require some special software on the client machines, or can they be used by standard out-of-the-box Windows computers? And, finally: how to set up this?

  Read the article

• Stop Cisco AnyConnect from locking down the NIC

  - by Johannes Rössel

  Cisco's VPN crapclients (including the AnyConnect one) have the nasty habit of clobbering all NICs on the system you're using them. The old client had a checkbox in the connection options that allowed you to use other network interfaces while being connected while the AnyConnect client doesn't have any options at all, seemingly. But they both lock down the network interface they are using to connect to the VPN. Since I am forced to use AnyConnect to actually have an internet connection and I like to control a second computer at home via RDP (over the same network interface so far) this doesn't quite work out. With the old client IPv6 still worked just fine, though AnyConnect seems to dislike that as well now. Is there any way to still use the same network interface for LAN access? I actually don't really care about any possible security implications (which might be why Cisco does this) as it's my freaking internet connection and not a secure way of working from home. The trade-off is quite different :-)

  Read the article

• Determining the health of a Cisco switch port?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced recently, however, the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link. We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• Cisco WebVPN RDP Plugin and NLA

  - by bab

  I'm having trouble finding anything in Cisco's docs or with Google searches, so I'm hoping someone out in ServerFault land might know. We've recently enabled NLA domain-wide to protect against some of the recent RDP vulnerabilities. However, we can no longer use the Cisco WebVPN on our ASA to connect to these boxes (Connection Failure). I assume this is because the RDP2 plugin (as of Apr 27 2012) doesn't support NLA? Is there another version of the plugin that does? Thanks!

  Read the article

• Is my Cisco switch port bad?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• Quickbooks and Cisco ASA 5505

  - by user41516

  I have a Cisco ASA 5505, and everything has seemed to function fine, however I have had problems with Quickbooks 2008 running super slow over the network (Samba) and narrowed it down to the Cisco box. Other Samba transfers seem to be pretty fast, and the Quickbooks file is not very large at all (<25 MB), and other Samba transfers seem to be fine. However, I'm not sure if Quickbooks uses another protocol or if there are other ports that need to be opened. Can anybody give me any clues on how to resolve or troubleshoot the problem or have any prior experience with running Quickbooks over a network?

  Read the article

• Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

  - by Bo102010

  (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

  Read the article

• Cisco ASA not forwarding traffic from one interface to another

  - by Antoine Benkemoun

  Hello ServerFault, I am needing help in the configuration process of my Cisco ASA 5510. I have set up 4 Cisco ASA interconnected together via a big LAN. Each Cisco ASA has 3 or 4 LANs attached to them. The IP routing part is taken care of by OSPF. My problem is on another level. A computer connected to one of the LANs attached to an ASA has no problem communicating with the outside world. The outside world being anything "after" the ASA. My problem is that I am completely unable to have them communicate with another LAN connected to the same ASA. To rephrase this, I am unable to send traffic from one interface of a given ASA to another interface of the same ASA. My configuration is the following : ! hostname Fuji ! interface Ethernet0/0 speed 100 duplex full nameif outside security-level 0 ip address 10.0.0.2 255.255.255.0 no shutdown ! interface Ethernet0/1 speed 100 duplex full nameif cs4 no shutdown security-level 100 ip address 10.1.4.1 255.255.255.0 ! interface Ethernet0/2 speed 100 duplex full no shutdown ! interface Ethernet0/2.15 vlan 15 nameif cs5 security-level 100 ip address 10.1.5.1 255.255.255.0 ! interface Ethernet0/2.16 vlan 16 nameif cs6 security-level 100 ip address 10.1.6.1 255.255.255.0 ! interface Management0/0 speed 100 duplex full nameif management security-level 100 ip address 10.6.0.252 255.255.255.0 ! access-list nat_cs4 extended permit ip 10.1.4.0 255.255.255.0 any access-list acl_cs4 extended permit ip 10.1.4.0 255.255.255.0 any access-list nat_cs5 extended permit ip 10.1.5.0 255.255.255.0 any access-list acl_cs5 extended permit ip 10.1.5.0 255.255.255.0 any access-list nat_cs6 extended permit ip 10.1.6.0 255.255.255.0 any access-list acl_cs6 extended permit ip 10.1.6.0 255.255.255.0 any ! access-list nat_outside extended permit ip any any access-list acl_outside extended permit ip any 10.1.4.0 255.255.255.0 access-list acl_outside extended permit ip any 10.1.5.0 255.255.255.0 access-list acl_outside extended permit ip any 10.1.6.0 255.255.255.0 ! nat (outside) 0 access-list nat_outside nat (cs4) 0 access-list nat_cs4 nat (cs5) 0 access-list nat_cs5 nat (cs6) 0 access-list nat_cs6 ! static (outside,cs4) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 static (outside,cs5) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 static (outside,cs6) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 ! static (cs4,outside) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 static (cs4,cs5) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 static (cs4,cs6) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 ! static (cs5,outside) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 static (cs5,cs4) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 static (cs5,cs6) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 ! static (cs6,outside) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 static (cs6,cs4) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 static (cs6,cs5) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 ! access-group acl_outside in interface outside access-group acl_cs4 in interface cs4 access-group acl_cs5 in interface cs5 access-group acl_cs6 in interface cs6 ! router ospf 1 network 10.0.0.0 255.255.255.0 area 1 network 10.1.4.0 255.255.255.0 area 1 network 10.1.5.0 255.255.255.0 area 1 network 10.1.6.0 255.255.255.0 area 1 log-adj-changes ! There is nothing really complicated in this configuration. It just NATs from one interface to another and that's it. I have tried enabling same-security-traffic permit inter-interface but that doesn't help. I therefore must be missing something a little bit more complicated. Does anyone know why I cannot foward traffic from one interface to another ? Thank you in advance for your help, Antoine

  Read the article

• Cisco ASA site-to-site vpn not initiating phase 1 (not sending udp 500 packets)

  - by Sean Steadman

  I am hoping someone here can help me with my problem. I am trying to setup an IPSEC site-to-site VPN between two cisco ASA 5520's in GNS3 (both using 8.4.2). I have been unsuccesful in getting the tunnel up and it appears neither ASA is sending packets out,in regards to phase 1 and phase 2 (tested by using wireshark and seeing NO udp 500 packets). Doing show ipsec sa and such shows nothing. CALIFORNIA(config)# show ipsec sa There are no ipsec sas FLA-ASA# show ipsec sa There are no ipsec sas I will attach both configurations in two different pastebin files as to keep this post a bit cleaner. Essentially California side has 172.20.1.0/24 and Florida side has 10.10.10.0/24. California ASA config: http://pastebin.com/v0pngYzF Florida ASA config: http://pastebin.com/E2geybta Please let me know if there is any other vital information that could help. I have gotten IPSEC tunnels to work using openSwan (linux) and cisco routers but cannot for the life of me get ASA IPSEC tunnels to work. The ASDM is out of the question I only use cli. Thanks for any useful help!

  Read the article

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• Linux tools to choose suitable Cisco ASA 5500

  - by linuxcore

  I have a linux webhosting server which affects a high DDOS. I want to use Cisco ASA 5500 Series Adaptive Security Appliances to protect the linux server from this DDOS. I know there are many factors should you know before you choose the suitable hardware firewall like the amount of this DDOS and pps ..etc Please suggest a linux tools to measure those factors and to help me collect the required informations ( pps - amount of DDOS - concurrent connections and other factors ) Regards,

  Read the article

• Alternative routers to the Cisco SA 500

  - by Justin

  We are evaluating the Cisco SA 500 router for our new office router. Would anyone recommend another similarly-featured router from another manufacturer? Requirements: - Office of 14 people - We are likely to switch to 14 VOIP phones (Linksys SPA-942) soon - We want to use VPN on the router, if possible, with Windows and Mac users

  Read the article

• VLAN trunking between Juniper EX -> Cisco Catalyst -> and Cisco Router

  - by Hugo Garcia

  I have the following scenario: EX2200 Switch whit ge-0/0/6 set as an access port on VLAN 80 ge-0/0/0 set as a trunk port connected to a catalyst switch and various vlans allowed to pass includin vlan 80 On the Catalyst Switch. port #3 set up as a trunk port that receives traffic from the EX switch. port 46 is set up also as a trunk port that connects to a cisco router. Port #48 is where the host used to be connected host - EX2200 - Catalyst - Router the problem is that this EX2200 is a new addition to the network and the host connected previosly to the catalyst switch. traffic is not getting from the host to the router, but the router can send ARP request to the host. following is the relevant configuration: Catalyst Switch: interface GigabitEthernet1/46 switchport trunk encapsulation dot1q switchport trunk allowed vlan 80,82,83,93,289 switchport mode trunk mtu 1532 media-type rj45 speed 1000 duplex full arp timeout 300 ! interface GigabitEthernet1/48 switchport access vlan 80 switchport mode access mtu 1532 media-type rj45 speed 100 duplex full arp timeout 300 no cdp enable ! EX2200 Switch:

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• TheGreenBow VPN with Cisco 2811 config

  - by Fujishiro

  Okay. Im using the feared x64 Win7 retail. I tried soooo many clients/methods, but none of them worked. Finally after a long battle, I made TGB working. YAY! I only have problems with the configuration. What data I've got? group auth user+pw;3DES enc(saw it from the router cfg);user+password. And that's all. I tried using the TGB provided manual and the howtos on their site, but there is no instruction for the given model, and the other cisco type conf wont work.) I tried to configure it up, but its not that easy.. as I mentioned aldy. If anyone uses this app or knows how to configure it up... please..help me.

  Read the article

• Cisco redundancy modes

  - by user974896

  I am using a Cisco 6500 series with an SSO redundancy configuration. The show redundancy output is as follows: Hardware Mode = Duplex Configured Redundancy Mode = sso Operating Redundancy Mode = rpr Maintenance Mode = Disabled Communications = Up I would assume the device is operating in RPR mode although SSO is configured. What could cause this? Shouldn't the operating mode be SSO? EDIT (show redundancy states): my state = 13 -ACTIVE peer state = 4 -STANDBY COLD Mode = Duplex Unit = Primary Unit ID = 5 Redundancy Mode (Operational) = rpr Redundancy Mode (Configured) = sso Redundancy State = rpr Split Mode = Disabled Manual Swact = Enabled Communications = Up client count = 60 client_notification_TMR = 30000 milliseconds keep_alive TMR = 9000 milliseconds keep_alive count = 1 keep_alive threshold = 18 RF debug mask = 0x0

  Read the article

• Auto login CISCO VPN client on linux [closed]

  - by user70704

  Hi, I have installed Cisco vpn client on my linux system (Fedora core 8). After login, every time, i need to run the following command VPNC to connect the VPN server. VPNC command request the input data from the user, IPSec gateway : IPSec ID: IPSec Secret: Username: Password: So, my requirement is, can i connect the VPN server through any single command?. I feel so lazy to enter the above requirements at every time. I want to connect the VPN Server on boot startup. I was try using expect script, but i can't. Thanks in advance.

  Read the article

• Text on Cisco ASA console is garbled/missing letters

  - by Some Linux Nerd

  I've actually looked up a number of solutions for this problem and none of them work. There's this Cisco ASA 5505 that I'd like to use, that outputs mildly garbled text with missing characters. I did some googling and found that the most likely problem is a bad baud rate, so I tried all the baud rates, 7N1, 8N2... basically every possibility minicom had. Then I figured (since I can type ok, just not read) that if I factory reset it that it would fix whatever is set wrong with the terminal. That didn't work either. This usb-db9 adapter and console cable work fine on the catalyst switch in our office. My serial settings are 9600 8N1 with no flow control. Anyone know how to fix this? I have an example of the text on pastebin: http://pastebin.com/MAJF0mVU - it's just lots of "Dfaut cnfiuraionfil cotais 1enty." instead of "Default configuration blah blah"

  Read the article

• Setup Web Applications on Cisco ASA 9.1

  - by Scott

  I've been looking around the Cisco ASA administration screen with our network admin and haven't found the location where Web Applications can be setup. This seems like it should be a pretty straight forward procedure, especially if I just want to add a global application and not segment out by groups. I've looked through the docs, but they are a mess and answer most questions except for this. If you're going to post a RTFM answer, at least please provide link and location because I have looked. This is the location I'm looking to setup web applications on the clientless web VPN.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >