Search Results

Search found 2516 results on 101 pages for 'gigabit ethernet'.

Page 2/101 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Getting Ethernet driver to crippled machine

    - by Richard
    The reply at How do I install drivers for the Atheros AR8161 Ethernet controller? probably helps me. I have a Toshiba S855, bought yesterday. lspci -vv | grep Atheros command from the terminal shows me I have the AR8161 Gigabit Ethernet controller (rev 10) However the answer sudo apt-get install ... requires an internet connection. How can I, using another machine, capture the necessary information on that other machine to copy across to the crippled machine, and then how do I build from there. Thanks in anticipation

    Read the article

  • Ethernet Wired Connection Help

    - by user107598
    I have recently installed Ubuntu 12.10 onto my Dell Inspiron N5010 and Ive been all over many forums trying to figure out how I can get my ethernet cable to be recognized so I can set up a wired connection. My Network Card is the Realtek RT8139 and from what Ive gathered the ethernet port driver for it is installed. Whenever I run ifconfig in the terminal it says that eth1 is up and running but no matter how I edit the connection I cannot get it to work. If anyone can help it would be greatly appreciated!

    Read the article

  • Cannot connect to ethernet port

    - by Jnir
    I'm running Ubuntu 12.04 LTE. I'm trying to connect via ethernet for the first time but have had no success. Ifconfig eth0 returns: eth0 Link encap:Ethernet HWaddr: 00:01:2e:3f:f1:a0 inet6 addr: fe80::201:2eff:fe3f:f1a0 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:68 errors:0 dropped:0 overruns:0 frame:0 TX packets:183 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8374 (8.3 KB) TX bytes:42944 (42.9KB) Interrupt:16 Base address:0x6c00 /etc/network/interfaces has auto lo iface lo inef loopback auto eth0 iface eth0 inet dhcp sudo /etc/init.d/networking prints: * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... Failed to bring up eth0 [OK]

    Read the article

  • MySQL performance - 100Mb ethernet vs 1Gb ethernet

    - by Rob Penridge
    Hi All I've just started a new job and noticed that the analysts computers are connected to the network at 100Mbps. The ODBC queries we run against the MySQL server can easily return 500MB+ and it seems at times when the servers are under high load the DBAs kill low priority jobs as they are taking too long to run. My question is this... How much of this server time is spent executing the request, and how much time is spent returning the data to the client? Could the query speeds be improved by upgrading the network connections to 1Gbps? (Updated for the why): The database in question was built to accomodate reporting needs and contains massive amounts of data. We usually work with subsets of this data at a granular level in external applications such as SAS or Excel, hence the reason for the large amounts of data being transmitted. The queries are not poorly structured - they are very simple and the appropriate joins/indexes etc are being used. I've removed 'query' from the Title of the post as I realised this question is more to do with general MySQL performance rather than query related performance. I was kind of hoping that someone with a Gigabit connection may be able to actually quantify some results for me here by running a query that returns a decent amount of data, then they could limit their connection speed to 100Mb and rerun the same query. Hopefully this could be done in an environment where loads are reasonably stable so as not to skew the results. If ethernet speed can improve the situation I wanted some quantifiable results to help argue my case for upgrading the network connections. Thanks Rob

    Read the article

  • Disable Ethernet permanently to speed up boot time

    - by Anwar Shah
    I do not use the wired Ethernet Card. It seems to me that, Ubuntu is always trying in boot time to check the network via eth0, Which consumes some times and I guess this may slow down the boot process a bit. My dmesg output is below (partial) 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 1.985592] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input5 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 1.985651] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 1.985693] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 2.056261] firewire_core: created device fw0: GUID 00023f87af41fd7d, S400 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 3.710435] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null) A big time here..... 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 13.466642] ADDRCONF(NETDEV_UP): eth0: link is not ready 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.125296] Adding 1050620k swap on /dev/sda6. Priority:-1 extents:1 across:1050620k 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.226952] EXT4-fs (sda9): re-mounted. Opts: (null) 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.335012] snd_hda_intel 0000:00:1b.0: PCI INT A - GSI 22 (level, low) - IRQ 22 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.335091] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.335128] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.346410] input: Ideapad extra buttons as /devices/platform/ideapad/input/input6 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.428551] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.436958] cfg80211: Calling CRDA to update world regulatory domain 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.476550] Linux video capture interface: v2.00 2012-06-11 23:06:47 Ubuntu-KDE kernel [ 14.486385] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (04f2:b008) So, My question is How can I disable the Ethernet card completely, so that kernel will not try to use that?

    Read the article

  • Problems with wired ethernet connection Ubuntu 11.10

    - by Andrew Fielden
    After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

    Read the article

  • Share wireless Internet connection between Ubuntu 10.04 to Windows Vista through ethernet

    - by Artyom2033
    I am connected to the internet using a wireless connection on my laptop running ubuntu 10.04 and I want to share it to a desktop running windows Vista trough a Ethernet cable. How do I do that? I've try the "GUI Method via Network Manager (Ubuntu 9.10 and up)" on this page : https://help.ubuntu.com/community/Internet/ConnectionSharing but how to I access to it from Windows Vista? I didn't even know if it is shared. Thanks for the help

    Read the article

  • Bridge Laptop's Ethernet to Wireless

    - by Kalphiter
    The laptop wirelessly connects to my router, while the desktop is connected to the laptop with an ethernet wire. The desktop successfully can use the internet if I set the connection to be shared on the laptop. The problem is, I need the laptop to forward the desktop's packets across the link unmodified, so the desktop is on the same network as the router. The desktop needs its IP assigned by the router, so that I can access it from another computer as "192.168.1.8".

    Read the article

  • FCoE, on any Ethernet switch?

    - by javano
    I understand the concept of FCoE. I have looked at the Wikipedia page and looking at the layer 2 frame diagram, it looks like FCoE really should "just work" on any Ethernet switch, but is this really the case? If so, what do switches like Cisco's Nexus 5k or 6120P offer that normal switches don't (in specific relation to FCoE)? I am just using those two switches as examples. On the Nexus 5548UP page for example it says the following; Unified ports that support traditional Ethernet, Fibre Channel (FC),and Fibre Channel over Ethernet (FCoE) Well if FCoE runnins over regular Ethernet, that why does it support "Ethernet and Fibire Channel over Ethernet"? This is why I am curious as to weather FCoE will run on any Ethernet switch and these switches just support "bonus" features, or if you do indeed require a specialist switch. Thank you.

    Read the article

  • MySQL query performance - 100Mb ethernet vs 1Gb ethernet

    - by Rob Penridge
    Hi All I've just started a new job and noticed that the analysts computers are connected to the network at 100Mbps. The queries we run against the MySQL server can easily be 500MB+ and it seems at times when the servers are under high load the DBAs kill low priority jobs as they are taking too long to run. My question is this... How much of this server time is spent executing the request, and how much time is spent returning the data to the client? Could the query speeds be improved by upgrading the network connections to 1Gbps? Thanks Rob

    Read the article

  • No internet via wifi/ethernet after 14.04 upgrade

    - by Rhys Evans
    I have just updated to Ubuntu 14.04 LTS on my laptop, and I seem to be having some internet problems. I have no internet connection through wifi or Ethernet, after both working in the previous version. I am not at all knowledgeable of Ubuntu and its workings, so if you could just tell me what to do, what to show you by just telling me commands etc. I think would be the only way I will understand sorry! I am asking this after many searches, all being in vein after needing a step involving some sort of internet access, which I can't get! So sorry if it has been answered somewhere, if so, please send me there! Cheers This is what I get when using sudo lspci -v: lspci -v

    Read the article

  • Ubuntu 11.10 and Atheros AR8131 ethernet card

    - by nivcaner
    I have an Atheros AR8131 Ethernet card on a Lenovo b560 laptop. Sometime in the past, probably at some upgrade or other my wired connection stopped functioning. I know the card is ok because it works with windows. I tried upgrading to Ubuntu 11.10 hoping the problem would go away. It didn't... Tried to google the problem, but all of the solutions I found didn't work for me. This is probably a driver problem. Any help will be appreciated. Please note that I'm a linux newbie so I don't really know what logs to post... Niv

    Read the article

  • Ethernet not working on a Dell Inspiron 14z

    - by Izabela
    When I plug in a network cable, it is not recognized. The WI-FI is working properly, though. ifconfig output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1645 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:206840 (206.8 KB) TX bytes:206840 (206.8 KB) wlan0 Link encap:Ethernet HWaddr e0:06:e6:de:57:e7 inet addr:150.164.201.145 Bcast:150.164.201.255 Mask:255.255.255.0 inet6 addr: 2001:12f0:601:a921:98a2:3dd:3be8:c483/64 Scope:Global inet6 addr: 2001:12f0:601:a921:e206:e6ff:fede:57e7/64 Scope:Global inet6 addr: fe80::e206:e6ff:fede:57e7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23892 errors:0 dropped:0 overruns:0 frame:0 TX packets:14676 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30123226 (30.1 MB) TX bytes:2189050 (2.1 MB)

    Read the article

  • Ethernet not working in 12.04 (Dell Inspiron 14z)

    - by Izabela
    When I plug in a network cable, it is not recognized. The WI-FI is working properly, though. ifconfig output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1645 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:206840 (206.8 KB) TX bytes:206840 (206.8 KB) wlan0 Link encap:Ethernet HWaddr e0:06:e6:de:57:e7 inet addr:150.164.201.145 Bcast:150.164.201.255 Mask:255.255.255.0 inet6 addr: 2001:12f0:601:a921:98a2:3dd:3be8:c483/64 Scope:Global inet6 addr: 2001:12f0:601:a921:e206:e6ff:fede:57e7/64 Scope:Global inet6 addr: fe80::e206:e6ff:fede:57e7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23892 errors:0 dropped:0 overruns:0 frame:0 TX packets:14676 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30123226 (30.1 MB) TX bytes:2189050 (2.1 MB)

    Read the article

  • Beginner help with compiling a driver into the kernel so my ethernet works

    - by MattC
    I have a Acer Aspire Revo nettop and it seems like it's a common error that Ubuntu doesn't have a driver for the ethernet. Someone recommend following the steps on this page. http://manpages.ubuntu.com/manpages/jaunty/man4/nfe.4freebsd.html The only problem is that I have no clue what to do really. I'm almost like an absolute beginner with linux and was hoping to play with it by doing some apache+php+mysql stuff, however I cannot at the moment. Where is the kernel configuration file? and where is the loader.conf file?

    Read the article

  • Ubuntu 12.04 Ethernet works sporadically on lenovo x200 tablet

    - by user73100
    This is what I got from ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:16:1a:0e:7e inet6 addr: fe80::21f:16ff:fe1a:e7e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:387 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16036 (16.0 KB) TX bytes:98315 (98.3 KB) Interrupt:20 Memory:f2700000-f2720000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:704 errors:0 dropped:0 overruns:0 frame:0 TX packets:704 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:55280 (55.2 KB) TX bytes:55280 (55.2 KB)

    Read the article

  • ethernet problems in ubuntu 12.04

    - by h4x0rj3ff
    so today i popped out my hdd with ubuntu on it and put in a fresh hdd and installed win8 (wanted to try it). i got everything installed, upp and running and decided to go back to ubuntu (for obvious reasons lol) but when i boot back into ubuntu my internet connection will not connect. i booted into a live cd of ubuntu and it still would not work. i thought i blew up my onboard port so i booted back into win8 and the internet worked without flaw. so i booted back into my ubuntu install and i have a usb to ethernet adapter that im using but i still cant get my onboard to connect. any ideas?

    Read the article

  • My ethernet connection is not working but it is detected by my computer

    - by smithy545
    I'm setting up an old computer with ubuntu server 12.04. I wiped the drive and went through the installation fine but afterwards the ethernet would not work. It's physically connected to the router and the card is recognized by lspci(SiS 900) but it won't connect at all. I've plugged in and installed the drivers for a wifi adapter and it's worked with the same router. Just so you know I've turned it on and off plenty of times. Any help would be appreciated.

    Read the article

  • Gigabit connection between 2 computers

    - by Alecu
    I am trying to set up a connection between 2 pc's. It's a direct cable connection. The problem that I am having is that the connection isn't gigabit. I know both network cards support gigabit. I checked in the device settings and in one pc I can see in the Speed & Duplex the 1Gbps option but on the other pc I can't see that option despite the fact that the network card is gigabit. I have quite some files to copy from one pc onto another and I really need a good connection between them. I can't really remove the hard drive because it would void the warranty. Could this be a driver issue or a cable issue? On both pc's I have windows 8. The network card on the pc that doesn't have the 1 gbps option is an Atheros ar8161 card.

    Read the article

  • WiFi N Gigabit Router

    - by SLaks
    I'm looking for a WiFi N Gigabit router. I'll be using an iPod Touch 2G and a 2009 17" MacBook Pro over WiFi, and I need at least 4 gigabit ethernet ports plus a WAN port. What do people recommend? In particular, are there any compatibility issues between different WiFi N drafts that would limit the speed of the MacBook, and is it worth getting dual-band?

    Read the article

  • Gigabit capacity

    - by abronte
    Do gigabit ports have a total throughput of 1 gigabit so that you could be sending 800 mbit and receiving 200 mbit at the same time. Or is it 1000 in and 1000 out?

    Read the article

  • What could be the maximum number of hosts on a 100BaseTX ethernet network ?

    - by snowflake
    Hello, I'm having two ip networks (192.168.1.x and 192.168.2.x) bridged on a server, but all hosts (fixed IPs) are on the same physical 100BaseTX ethernet (with a daisy chain of 48ports switchs). Often, I loose link between the server and hosts of the second network. Usually if I reboot the host, the connection work again, and if I force connection to be active, the connection keep alive until I ping after a while without active connection. I'm wondering how many hosts can be connected on the same network without troubles, and eventually how many switches can be daisy chained ? I suppose maximum length between hosts to be 100meters to the hub or 200meters between extremity of the network. Somebody is suggesting 8 switches here : http://www.tek-tips.com/viewthread.cfm?qid=1137879&page=12 Any comments on how to find a solution to the problem and not answering directly to the question are welcomed!

    Read the article

  • 10 gigabit or 1 gigabit switch

    - by Guntis
    We are planning to move mysql to dedicated box. At this moment we have web servers and mysql is running on each. Question is: cheaper is to buy 10G switch and put 10G network card into mysql server. Or buy normal gigabit switch and connect mysql box to switch with multiple network cables. In 1G scenario then we give each web server different mysql IP address. I don't think, that mysql box with one 1G link is enough to to satisfy multiple web box mysql traffic. At this moment we have 3 servers witch are running mysql/web. Plan is to add fourth server for mysql only. Thanks. Edit: if we buy 1G switch with mini-GBIC ports. Can we put in mini-GBIC 10G connectors and then connect mysql box to that port?

    Read the article

  • Gigabit LAN not working on ASUS M2N-MX

    - by chmod
    Today I replace my FastEthernet switch with a newly bought gigabit switch (DGS-1008A). All computers in my house are displaying that the connection speed is 1 Gbps except for one. The computer that is not working is an ASUS M2N-MX which contain an onboard gigabit NIC. See ASUS link for confirmation http://www.asus.com/Motherboards/AMD_AM2/M2NMX/ Here are some info of the machine OS: Windows 7 Ultimate SP1 64bit BIOS version: 1004 (latest) Driver: installed via Windows update (latest from Windows update) Windows Update: fully updated The machine is reformatted 3 days ago, so it's pretty clean, no junk, no virus, etc Cable: Amp CAT5E 5 meters In device manager, the name of the NIC is "NVIDIA nForce 10/100/1000 Mbps Ethernet" What I have try: I did try to install the driver provided in ASUS website, but there isn't any for Windows 7 64 or Vista 64. I did try to install the latest nForce340/6100, downloaded from Nvidia website. However, the LAN driver refuse to install, it complain that I already have the best driver installed. I looking in the property -- advance tab -- Speed/duplex settings, in an attempt to force it to run at 1000Mbps, but there is no 1000Mbps choice, only 10 and 100Mpbs. I change the CAT5E cable (use one from another computer that is running gigabit without problem) Anyone have this issue or know how to solve it? Thanks

    Read the article

  • "Ethernet" doesn't have a valid IP configuration

    - by Xuzuno
    I'm using an ethernet cord to connect to my internet and it has been working well until Thursday morning when I turned on my laptop (Windows 8) to see a yellow triangle sign in the bottom right hand corner, in front of the ethernet connected symbol. Since then I haven't been able been able to access the internet from my computer. When I hover over it, it says that it is an "Unidentified network" and there is "No internet access". I've run the Windows 8 troubleshooting and it says that the problem found was ""Ethernet" doesn't have a valid IP configuration", but I'm unsure how to fix it. I'm thinking that the problem is to do with my computer rather than my network, because I've tried another laptop (Windows 7) through the same ethernet cable and connection and the internet works fine on the other laptop. I've tried so many fixes that I've found online, with none of them actually working. Yesterday I even tried a full system reset, where I re-installed Windows 8, re-partitioned and wiped everything off the hard drive, but it still appears have the exact same problem. Today I also purchased and tried a new ethernet cable which didn't work, so I then purchased a USB to Ethernet adapter, to make sure that it wasn't my ethernet port on my laptop that was faulty. That didn't work either, and the same problem still remains. I feel like I've tried everything, so can someone please help me?

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >