Search Results

Search found 503 results on 21 pages for 'cables'.

Page 20/21 | < Previous Page | 16 17 18 19 20 21  | Next Page >

• WDS DHCP same server on Windows Server 2008

  - by Richard

  I have been struggling with a problem on my Windows Server 2008 for the past 4 - 5 hours and cannot figure out whats wrong. I have tried pretty much everything that I found on google and all the links are purple. Hopefully you guys can help me. I am running a Windows Server 2008 Standard edition with the latest updates as of today. Furthermore I am running a Windows Server 2003. Both are virtual machines on my ESXi 5 server. My network is: 192.168.10.0/24 W2k8: 192.168.10.251 is the PDC running ADS, DHCP and WDS W2k3: 192.168.10.253 AND 192.168.1.175 running Routing and Remote Access and ISA 2006 Enterprise In my internal network (192.168.10.0/24) I have my client machine (192.168.10.10) that runs a VMWare Workstation. I am trying to deploy Windows 7 Home Premium to a virtual machine on my VMWorkstation via PXE. I have set the Workstation's VM network adapter to "bridged" so that it uses the physical network adapter and is connected to my internal network. The DHCP pool is configured to give IP addresses from 192.168.10.10-192.168.10.15 (works for normal clients and is not used up) When I start my VM with the PXE I get the error: PXE-E52:proxyDHCP offers were received. No DHCP offers were received Apperently this means "that means that WDS responded but the DHCP server did not." People suggested to direct the traffic to both WDS and DHCP on the router, since everything is on the same subnet there is no need for that as the broadcast is seen by everyone (WDS and DHCP) No reservation for the virtual mac addrs is made on the DHCP. Furthermore it was suggested to configure the DHCP options: Option 60= PXEClient Option 66= WDS server name or IP address Option 67= Boot file name However, this is not recommended by Microsoft, I tried it and it did not solve my problem. The configuration on the WDS (My System is German therefore the actual naming might be different): PXE response tab: PXE responses is set to "ALL (known and unknown)" DHCP Tab: Do not listen to port 67 is NOT ticked - if I tick this I do not get any responses and the PXE errors gets PXE-E51 that neither DHCP or proxyDHCP were received DHCP-Option 60 for "PXEClient" is ticked The confusing part here is that it is advised in the tab to tick the first option since it is on the same server. Network Configuration Tab: Use the following IP-Address range for Multicast-IP-Address: 224.0.1.0 - 224.0.10.0 Thats not the default one, however it is in the allowed range. The UDP port range is the default since it is not advised to change them. I tried to change the "networkprofile" from 100mbits/1gbits and custom. I am running a 1gbit network with CAT6 cables and 1gbit netgear switch 5 ports. Everything is configured to use 1gbit. The WDS is authorised for the DHCP server. My ISA 2006 configuration: For the internal networking i have configured the following policy array: Allow protocols on internal network including the w2k3 host: 67,68,53,ICMP, 4011 UDP receive, 64001-6500 UDP send receive, 69 UDP send Routing and Remote Access I tried the DHCP relay agent configuration that was suggested as well, but that did not work I would highly appreciate anykind of help because I am pretty much done here with my nerves. Thank you very much in advance.

  Read the article

• 2 drives, slow software RAID1 (md)

  - by bart613

  Hello, I've got a server from hetzner.de (EQ4) with 2* SAMSUNG HD753LJ drives (750G 32MB cache). OS is CentOS 5 (x86_64). Drives are combined together into two RAID1 partitions: /dev/md0 which is 512MB big and has only /boot partitions /dev/md1 which is over 700GB big and is one big LVM which hosts other partitions Now, I've been running some benchmarks and it seems like even though exactly the same drives, speed differs a bit on each of them. # hdparm -tT /dev/sda /dev/sda: Timing cached reads: 25612 MB in 1.99 seconds = 12860.70 MB/sec Timing buffered disk reads: 352 MB in 3.01 seconds = 116.80 MB/sec # hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 25524 MB in 1.99 seconds = 12815.99 MB/sec Timing buffered disk reads: 342 MB in 3.01 seconds = 113.64 MB/sec Also, when I run eg. pgbench which is stressing IO quite heavily, I can see following from iostat output: Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 231.40 0.00 298.00 0.00 9683.20 32.49 0.17 0.58 0.34 10.24 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 231.40 0.00 298.00 0.00 9683.20 32.49 0.17 0.58 0.34 10.24 sdb 0.00 231.40 0.00 301.80 0.00 9740.80 32.28 14.19 51.17 3.10 93.68 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 231.40 0.00 301.80 0.00 9740.80 32.28 14.19 51.17 3.10 93.68 md1 0.00 0.00 0.00 529.60 0.00 9692.80 18.30 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.60 0.00 4.80 8.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 529.00 0.00 9688.00 18.31 24.51 49.91 1.81 95.92 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 152.40 0.00 330.60 0.00 5176.00 15.66 0.19 0.57 0.19 6.24 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 152.40 0.00 330.60 0.00 5176.00 15.66 0.19 0.57 0.19 6.24 sdb 0.00 152.40 0.00 326.20 0.00 5118.40 15.69 19.96 55.36 3.01 98.16 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 152.40 0.00 326.20 0.00 5118.40 15.69 19.96 55.36 3.01 98.16 md1 0.00 0.00 0.00 482.80 0.00 5166.40 10.70 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 482.80 0.00 5166.40 10.70 30.19 56.92 2.05 99.04 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 181.64 0.00 324.55 0.00 5445.11 16.78 0.15 0.45 0.21 6.87 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 181.64 0.00 324.55 0.00 5445.11 16.78 0.15 0.45 0.21 6.87 sdb 0.00 181.84 0.00 328.54 0.00 5493.01 16.72 18.34 61.57 3.01 99.00 sdb1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sdb2 0.00 181.84 0.00 328.54 0.00 5493.01 16.72 18.34 61.57 3.01 99.00 md1 0.00 0.00 0.00 506.39 0.00 5477.05 10.82 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-1 0.00 0.00 0.00 506.39 0.00 5477.05 10.82 28.77 62.15 1.96 99.00 And this is completely getting me confused. How come two exactly the same specced drives have such a difference in write speed (see util%)? I haven't really paid attention to those speeds before, so perhaps that something normal -- if someone could confirm I would be really grateful. Otherwise, if someone have seen such behavior again or knows what is causing such behavior I would really appreciate answer. I'll also add that both "smartctl -a" and "hdparm -I" output are exactly the same and are not indicating any hardware problems. The slower drive was changed already two times (to new ones). Also I asked to change the drives with places, and then sda were slower and sdb quicker (so the slow one was the same drive). SATA cables were changed two times already.

  Read the article

• Fix overscan in Linux with Intel graphics Vizio HDTV

  - by Padenton

  I am connecting my server to my HDTV so that I can conveniently display it there. My VIZIO HDTV cuts off all 4 edges. I already realize it is not optimal to be running a GUI on a server; this server will not have much external traffic so I prefer it for convenience. I have already spent countless hours searching for a fix, but all I could find required an ATI or NVIDIA graphics card, or didn’t work. In Windows, the Intel driver has a setting for underscan, though it seems only to be available by a glitch. Here’s my specs: Ubuntu Linux (Quantal 12.10) (Likely to switch to Arch) This is a home server computer, with KDE for managing(for now, at least) Graphics: Intel HD Graphics 4000 from Ivy Bridge Motherboard: ASRock Z77 Extreme4 CPU: Intel Core i5-3450 My monitors: Dell LCD monitor Vizio VX37L_HDTV10A 37" on HDMI input I have tried all of the following from both HDMI?HDMI and DVI?HDMI cables connected to the ports on my motherboard: Setting properties in xrandr Making sure drivers are all up to date Trying several different modes The TV was “cheap”; max resolution 1080i. I am able to get a 1920x1080 modeline, in both GNU/Linux and Windows, without difficulty. There is no setting in the menu to fix the overscan (I have tried all of them, I realize it’s not always called overscan). I have been in the service menu for the TV, which still does not contain an option to fix it. No aspect ratio settings, etc. The TV has a VGA connector but I am unsure if it would fix it, as I don’t have a VGA cable long enough, and am not sure it would get me the 1920x1080 resolution which I want. Using another resolution does not fix the problem. I tried custom modelines with the dimensions of my screen’s viewable area, but it wouldn’t let me use them. Ubuntu apparently doesn’t automatically generate an xorg.conf file for use. I read somewhere that modifying it may help solve it. I tried X -configure several times(with reboots, etc.) but it consistently gave the following error messages: In log file: … (WW) Falling back to old probe method for vesa Number of created screens does not match number of detected devices. Configuration failed. In output: … (++) Using config file: "/root/xorg.conf.new" (==) Using system config directory "/usr/share/X11/xorg.conf.d" Number of created screens does not match number of detected devices. Configuration failed. Server terminated with error (2). Closing log file. Tried using 'overscan' prop in xrandr: root@xxx:/home/xxx# xrandr --output HDMI1 --set overscan off X Error of failed request: BadName (named color or font does not exist) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 11 (RRQueryOutputProperty) Serial number of failed request: 42 Current serial number in output stream: 42 'overscan on', 'underscan off', 'underscan on' were all also tried. Originally tried with Ubuntu 12.04, but failed and so updated to 12.10 when it was released. All software is up to date. I am not opposed to reinstalling my OS, likely will anyways (my preference being Arch).

  Read the article

• Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

  - by Joe Hopfgartner

  I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

  Read the article

• XFS disk becomes unavailable after a while

  - by Guard

  Ubuntu 12.04 (but the same was on 11.10 before upgrading) WD MyBook, 2TB, no RAID (or RAID0, not completely sure, anyway no mirroring, both 1TB disks are in use, mounted as a single device). Formatted to XFS, normally used for big movie files. Connected to Firewire 800. At some point the LED started going up and down as when constantly reading/writing. The device gives access error. When unplugged (cable, then holding the power button for a while, then unplugging the power) and re-connected becomes available. xfs_check with no results. xfs_repair did something, but looks like didn't fix any error. Then after a massive read (checking 1.5GB torrent file for integrity) becomes unavailable again. Any ideas what's wrong? Drives? Cables? Motherboard? OS? UPD: not sure how relevant this is, but here are dmesg output [14380.632816] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [14380.633356] SGI XFS Quota Management subsystem [14421.812220] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.890596] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.896858] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14453.895347] firewire_core: created device fw1: GUID 0090a99500a35518, S400, 9 config ROM retries [14453.904818] scsi6 : SBP-2 IEEE-1394 [14453.905014] scsi7 : SBP-2 IEEE-1394 [14454.139993] firewire_sbp2: fw1.0: logged in to LUN 0000 (0 retries) [14454.158769] scsi 6:0:0:0: Direct-Access WD My Book 1015 PQ: 0 ANSI: 4 [14454.159251] sd 6:0:0:0: Attached scsi generic sg3 type 0 [14454.162391] firewire_sbp2: fw1.1: logged in to LUN 0001 (0 retries) [14454.167453] sd 6:0:0:0: [sdc] 3907017568 512-byte logical blocks: (2.00 TB/1.81 TiB) [14454.178822] sd 6:0:0:0: [sdc] Write Protect is off [14454.178826] sd 6:0:0:0: [sdc] Mode Sense: 10 00 00 00 [14454.186830] scsi 7:0:0:1: Enclosure WD My Book Device 1015 PQ: 0 ANSI: 4 [14454.186995] scsi 7:0:0:1: Attached scsi generic sg4 type 13 [14454.190078] sd 6:0:0:0: [sdc] Cache data unavailable [14454.190087] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.202176] sd 6:0:0:0: [sdc] Cache data unavailable [14454.202185] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.239940] sdc: [mac] sdc1 sdc2 sdc3 sdc4 [14454.271262] sd 6:0:0:0: [sdc] Cache data unavailable [14454.271270] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.271354] sd 6:0:0:0: [sdc] Attached SCSI disk [14454.272149] ses 7:0:0:1: Attached Enclosure device [14606.090024] XFS (sdc3): Mounting Filesystem [14612.048343] XFS (sdc3): Starting recovery (logdev: internal) [14620.697636] XFS (sdc3): Ending recovery (logdev: internal) [14748.120957] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [14748.120963] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO [14752.568382] uhci_hcd 0000:00:1a.0: PCI INT A disabled [14752.568579] uhci_hcd 0000:00:1a.1: PCI INT B disabled [14752.568738] ehci_hcd 0000:00:1a.7: PCI INT C disabled [14752.568779] ehci_hcd 0000:00:1a.7: PME# enabled [14752.584526] uhci_hcd 0000:00:1d.1: PCI INT B disabled [14752.584689] uhci_hcd 0000:00:1d.2: PCI INT C disabled [14752.680079] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xe4641000-0xe46413ff] (PCI address [0xe4641000-0xe46413ff]) [14752.680104] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b) [14752.680136] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002) [14752.680170] ehci_hcd 0000:00:1a.7: PME# disabled [14752.680182] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.680190] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [14752.710334] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [14752.710342] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [14752.749186] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [14752.749194] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [14752.790231] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 [14752.790239] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [14752.829170] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.829178] uhci_hcd 0000:00:1d.2: setting latency timer to 64

  Read the article

• Determining the required depth and specifications for a server cabinet

  - by Bingu Bingme

  I'm trying to understand the considerations ("why") that go into determining the specifications ("what") for a rackmount server cabinet, in order to determine what sort of rack I should purchase for my home use. Since this is for home use, I won't be following certain best practices (eg. hot/cold aisle, not even air conditioning) and may be willing to sacrifice in various areas in order to reduce cost and footprint - but please advise if there are safety concerns or other considerations to note. The most basic specs for a server cabinet are the dimensions (external width x external depth x usable height). Width: commonly 600mm or 800mm (if the use case requires extra clearance around the sides, such as if there is lots of cabling). In my case and most common cases, I'm going to stick with 600mm. Height: Select a sufficiently tall rack to fit my equipment. But how much may I stuff into it? Eg, if there is a 15U rack, can I really populate it with 15U of servers, or should I leave 1U at top and bottom for air circulation? Depth: Racks commonly have external depth of 600mm (network equipment), 800mm, 1000mm, or even longer. I'm trying to see how to fit into the 800mm depth. With reference to http://www.server-racks.com/rack-mount-depth.html, I'm hoping to have the front and rear posts mounted ~ 28.5" (72cm) apart, which would leave only 8cm for front space and rear space. How much rear space (from rear posts to back of rack) do I really need? I won't use cable management arms, so can I mount a 72cm depth server since the power, KVM, network cables won't take up much depth? My most important equipment are all < 60cm depth (4U chassis) and should comfortably fit within the 800mm cabinet. The rest of the equipment are very old 1U servers that range from 65-72cm depth. I might still want to make further use of them, or I might discard them since they are so old. Even if the 72cm servers cannot be powered on in an 800mm rack, I should be able to use them as 1U shelves. But, what server depth can I expect to be able to operate? Or am I forced to upgrade to 1000mm depth racks in order to use any servers deeper than 60cm? With reference to best practices for HP racks, some other specs and installation considerations: There aren't any minimum recommendations for clearance on the sides of the rack. It is recommended to leave 48" front clearance. The 48" front clearance is based on 32" chassis depth, 13" to extend the rack rails and mate the inner/outer rails, and 3" for movement. If I don't use such rails (eg, use shelves instead), it should be sufficient to leave front clearance of chassis depth + 3". It is recommended to leave 30" rear clearance "to provide space for servicing the rack". I'm planning to back the rack into a corner of the room, and wheel it slightly out when I need to access the rear. If the wheeling plan is ok, I still need to know how much rear clearance is required for air circulation and ventilation purposes. Castor wheels and stabilising feet. Since I'm backing the rack into a corner of the room, I'll only be able to set the stabilising feet on the front corners. Thoughts on safety? The rack that I'm considering has front glass doors with side ventilation slits and fully perforated rear doors. I'm hoping this will be a good balance between temperature and noise (only ventilation slits facing out the front, while the rear is facing the walls). Or is the sound of high-rpm fans going to escape through the front slits anyway and destroy my sanity?

  Read the article

• Dell Latitude E6430 Docking Station + Dual Monitor + Laptop Screen Tri-Monitor setup

  - by Larry

  I have a company issued laptop and docking station as well as two monitors The specifications of the hardware are as follows; Laptop: Latitude E6430 BIOS: A02.00 Processor: i7-3720QM CPU @ 2.60 (8 CPUs) Memory: 4096MB RAM Page file: 1825MB used, 4793MB available DirectX 11 Display Driver/Chip: MVIDIA NVS 5200M DAC: Integrated RAMDAC Aprox Total Memory: 2376 (Above 3 details same for both displays) Current Display Mode (Display 1): 1600x900 Current Display Mode (Display 2): 1440x900 the docking station is a Dell Latitude E6420 Docking Station PR03X Port Replicator and I don't think the monitor model is particularly relevant to resolving this issue but they are both Acer V193Ws The story goes like this; the laptop works fine if I VGA one monitor into the laptop through the vga port on the back of the lefthand side of the laptop I can achieve dual monitor display fine (laptop screen + monitor) if I plug the laptop into the docking station and use the vga port in the back of the docking station I can dual monitor fine (laptop screen + monitor) if I plug the laptop into the docking station, the laptop's lefthand side VGA port no longer seems to function at all I've spoken to internal IT about this issue and they're going to get me some kind of VGA splitter or a DVI-VGA adapter to use with the docking station for the second Acer Monitor, but that isn't going to happen for a few days. So I guess what I'm wondering is; is there any way to continue to use the side VGA port on my laptop while using the docking station VGA port? and as a secondary 'followup' pending resolution of the initial issue with getting both monitors up and running (at the moment I have both monitors on my desk but am just using my laptop screen as one of my dual monitor display with one of the monitors [the one connected to dock]), is there any way to CONTINUE to use my laptop monitor to in effect have a triple monitor display (2 monitors + docked laptop)? I am wondering this because internal IT told me that they were aware of some issues with the particular display drivers in my box and triple monitor displays but weren't really going to look TOO much in-depth into that (which is perfectly understandable) since getting the adapter for the dual monitors up and running was the greater priority within their purview. So this is a two parter; Can I dual monitor using two vga cables with 1 docking station vga port and one laptop vga port? is there a setting that can be tweaked somewhere? because plugging the box into the station seems to make the side port stop working and... Is there any reasonably simple and cost-effective work around (e.g. I am find with shelling out maybe a few dollars out of my own pocket for some hardware or software to make my company box tri-display capable) but if this requires some extensive rebuild or new OSs or doing stuff to the BIOS I'd rather have a straight answer about this being untenable as a slight modification to a (once again) company laptop and stop wasting time looking into it Thanks! and please let me know if you guys need any more details (tech specs or something) to answer this question [EDIT] 2/10/2014 Just an update; turned out it really was just a hardware limitation issue. The old laptop just couldn't hack it. Got a new laptop with a better video card and different monitors from my company and am successfully using a triple display currently (2 monitors + laptop screen)

  Read the article

• Rosewill RSV-S5 and it's transferespeeds

  - by DoomStone

  I have just bought a Rosewill RSV-S5, I have installed 5x1,5Tb Western Digital Green disks in it. After that have I created a Raid5 on them all with the software that followed with the hardware. Not the raid it self works fine, but it is SLOW, I can only obtain a maximum of 25 MB/s, and if SABnzbd+ is downloading with 5 MB/s is it having a hard time streaming a normal DIVX (700 mb) movie. Is this normal or is there something wrong? Edit: should be able to handle 3 Gbps = 384 megabytes / second Edit 2: As you can see am I only downloading with 3,76 MB/s and I'm trying to watch V s02e08 (720p), but it is completely unwatchable, as I can see 30 sec, and the it buffers for 20 sec. Edit: Other information there might be required I'm running Windows Server 2008 R2, optimized for program performance. Windows is installed on a 60GB SSD. I have a 50 Mb/s internet connection and a 1 Gb/s LAN, all connected with Cat6 Ethernet cables. The MCE is using a Gigabyte EP35C-DS3R motherboard with 2 GB DDR2 ram. Edit 3: I have used chunk sizes for 128 KB Edit 4: I found this on newegg Pros: Enclosure for 5x2TB hard drive is fine. This is basically a rebranded San Digital TR5M-B product. For support Rosewill tells you to contact San Digital. No direct support from Silicon Image for the computer raid card. Cons: Includes computer Silicon Image 3132 raid card, extremely slow raid 5 write (our tests ~10MB/s). Compare to regular internal local drive write 30-60MB/s. We basically dumped the Sil3132 card and replaced with High Point RocketRaid 622 card for extra $69.99. Note for RR622, turn off ECRC (end to end CRC check) for card to work on IBM xserver. What took 12hrs to copy now took 2-3hrs. San Digital realized the problem and has the newer model TR5M-BP TowerRaid Plus that comes with High Point RocketRaid 622 card. Rosewill should discontinue this product and go with TR5M-BP. Could not get Silicon Image raid management software to work with complicated 2008R2 server with 10 NICs, application doesn't know how to talk to localhost port with all those NICs. No updates from Silicon Image and support from San Digital ignored. Gave up on Sil3132 card. Save yourself from a lot of headaches, get the RR622 card too if you are going to buy this product. Other Thoughts: The newer model is TR5M-BP TowerRaid Plus, comes with High Point RocketRaid 622 raid card for the PC instead of Silicon Image Sil3132. According to San Digital, raid 5 performance for Sil3132 read 80MB/s write 19MB/s, and RR622 read 154MB/s write 149MB/s. Our RR622 tests gave (8TB raid 5) write ~80-110MB/s copying 40GB file took 8mins. So I have now ordered a HighPoint RocketRAID 622 2P ext SATA III and hopes that it will solve my problems.

  Read the article

• My 2009 MacBook Logic board failed - options to proceed and how difficult?

  - by user181061

  Scannerz just gave my MacBook logic board a big fat F! I upgraded from Snow Leopard to Mountain Lion about 3 weeks ago. The system was running short of memory so I upgraded it. The system was running fine for about 2 weeks. Yesterday the thing started acting erratic. A lot of spinning beach balls, delays, and then some errors saying files couldn't be read to or from the drive. I figured the drive was going because the system is over 3 years old. I ran Scannerz on it and it indicated a lot of errors and irregularities. I rescanned it in cursory mode, and none of them were repeatable, just showing up all over the place in different regions of the scan. I went through the docs and they implied either an I/O cable was bad, a connection was damaged, or the logic board was bad. I tossed on my backup of Snow Leopard that I cloned from the original hard drive because I figured Mountain Lion was to blame and booted from the USB drive with the clone on it. It wasn't. I performed scans on every single port, and errors and irregularities that couldn't be repeated were showing up on every single one of them. I then, for kicks, put a CD into the CD player. Scannerz doesn't test optical drives but I figured surely that will work. No it won't. More spinning beach balls and messages telling me it can't be read. It was working fine 3 days ago. I know a lot of people don't like MacBook's, but mine's been great, at least until now. It was working great even with Mountain Lion after the upgrade. The system is a mid-2009 MacBook. In my opinion, it's a complete waste to toss this system. The display is too good, the keyboard works great, and it still looks good, plus this type of MacBook still uses the FireWire 400 port and I use that for Time Machine backups. I've tried reseating the RAM, it didn't do anything. I shut the system down and put in the old RAM, booted to Snow Leopard, and the problems persist. Here are my questions: The Scannerz documentation somewhere said something about the Airport card not being seated properly, but when I go to iFixit, it's apparent, at least I think it's apparent, that this isn't a slot type Airport card that the user can easily install or remove. If the cables or connections to the Airport card are bad, could they be causing this problem. How about any other connections that can be intermittent, failing or erratic? Any type of resets that I could possibly do to get rid of this? For any of those that have replaced a logic board on a MacBook, if this really is the culprit, are there any "gotcha's" I need to be aware of? As an FYI, I replaced the hard drive on an old iBook @500MHz that I had a long time ago, and I replaced the drive on a 1.33GHz PowerBook about 6 years ago. You have to be careful, but using some of the info on web sites like iFixit it's not that hard. Time consuming, but not that hard. The Intel based MacBook's to me look like they're easier to service than either of those. I'm thinking about getting a unit off of eBay that matches mine but has something else wrong with it, like a busted display. I REFUSE to buy a new system. A guy at my office has a 2007 Mac Pro and he can't upgrade to Mountain Lion because his system is "obsoleted." That's ridiculous. If you pay nearly $7,500 for a system it shouldn't be trash just because Apple decides they don't have enough money (sorry for the soap box, but it's true, IMO!) Any input is appreciated.

  Read the article

• Windows 7 is stuck at "Starting Windows" when I attempt to boot computer

  - by Eli

  Basically, whenever I turn on my computer, it gets to the Starting Windows phase and just stays there. The startup animation still plays, yet it gets nowhere. I have tried booting into safe mode, however it gets stuck at loading CLASSPNP.SYS. It then freezes there and doesn't continue booting. I have tried booting into recovery mode from the hard drive, and it freezes after displaying the background image. I have tried booting from a recovery CD, which works, and I was able to use system restore. However, using system restore did not fix it, and it still is stuck at the Starting Windows screen. I have tried booting a Windows CD (Windows 8 Retail Installer) to see if I could upgrade it to fix this issue, however that froze at a blank screen after it got past the boot logo. I have tried changing around the BIOS settings (including resetting), to no avail. I have tried re-plugging the internal PSU cables (this is a custom-built desktop), yet this has changed nothing. I can boot into a loopback Ubuntu install on the same drive, which works fine, other than the fact that it has issues with some of the USB ports and the network card. This system has worked fine for the past few months, completely stable, and nothing in the configuration has changed before this error started happening. Startup Repair on the Windows recovery CD doesn't find any issues. Unplugging my secondary hard drive or swapping around memory doesn't change anything. The hard drive itself is fine, it hasn't shown any signs of failure and once again, boots my other OS fine. If anyone could help with this, that would be great. I can't seem to find any possible solution to this. If it makes any difference, my system specs are as follows: AMD FX-8320 Gigabyte GA-970A-D3 4GB of DDR3 Radeon HD 6870 550w PSU I'd like to not have to reinstall Windows, for I have more than a terabyte of data that I would have to back up if that becomes the only option. EDIT: I have since tried the following: Tried the solution involving restoring files from RegBackup, which changed nothing. Tried testing everything with Hiren's boot CD, everything comes back as fine. Tried disabling everything unnecessary in the BIOS and unplugging everything unneeded, it still hangs. Tried swapping out every possible combination of RAM, it still has the same result. The RAM is not at fault it seems Tried every GPU I own (which is many!) and it still hangs at the exact same place. Tried minimizing the power consumption as much as possible, even using an old PCI graphics card. It still hangs at the same place in the same way, signifying that it's not the PSU at fault. Tried resetting the BIOS again, still nothing. Tried every possible combination of BIOS options, even downclocking everything, it still hangs in the same spot. Tried upgrading the BIOS from version FB to FD, which changed nothing. Based on this, I would conclude the motherboard to be at fault. Are there any other possibilities? I don't want to spend $150 for a new motherboard. EDIT 2: This is what it gets stuck at when I try to boot into safe mode: Note the slight graphical corruption at the top of the screen. No matter how I set up the system, this seems to be there. In addition, either it has stopped booting into safe mode now, or it takes upwards of 2+ hours, and I haven't left it running for that long.

  Read the article

• Robotic Arm &ndash; Hardware

  - by Szymon Kobalczyk

  This is first in series of articles about project I've been building  in my spare time since last Summer. Actually it all began when I was researching a topic of modeling human motion kinematics in order to create gesture recognition library for Kinect. This ties heavily into motion theory of robotic manipulators so I also glanced at some designs of robotic arms. Somehow I stumbled upon this cool looking open source robotic arm: It was featured on Thingiverse and published by user jjshortcut (Jan-Jaap). Since for some time I got hooked on toying with microcontrollers, robots and other electronics, I decided to give it a try and build it myself. In this post I will describe the hardware build of the arm and in later posts I will be writing about the software to control it. Another reason to build the arm myself was the cost factor. Even small commercial robotic arms are quite expensive – products from Lynxmotion and Dagu look great but both cost around USD $300 (actually there is one cheap arm available but it looks more like a toy to me). In comparison this design is quite cheap. It uses seven hobby grade servos and even the cheapest ones should work fine. The structure is build from a set of laser cut parts connected with few metal spacers (15mm and 47mm) and lots of M3 screws. Other than that you’d only need a microcontroller board to drive the servos. So in total it comes a lot cheaper to build it yourself than buy an of the shelf robotic arm. Oh, and if you don’t like this one there are few more robotic arm projects at Thingiverse (including one by oomlout). Laser cut parts Some time ago I’ve build another robot using laser cut parts so I knew the process already. You can grab the design files in both DXF and EPS format from Thingiverse, and there are also 3D models of each part in STL. Actually the design is split into a second project for the mini servo gripper (there is also a standard servo version available but it won’t fit this arm).  I wanted to make some small adjustments, layout, and add measurements to the parts before sending it for cutting. I’ve looked at some free 2D CAD programs, and finally did all this work using QCad 3 Beta with worked great for me (I also tried LibreCAD but it didn’t work that well). All parts are cut from 4 mm thick material. Because I was worried that acrylic is too fragile and might break, I also ordered another set cut from plywood. In the end I build it from plywood because it was easier to glue (I was told acrylic requires a special glue). Btw. I found a great laser cutter service in Kraków and highly recommend it (www.ebbox.com.pl). It cost me only USD $26 for both sets ($16 acrylic + $10 plywood). Metal parts I bought all the M3 screws and nuts at local hardware store. Make sure to look for nylon lock (nyloc) nuts for the gripper because otherwise it unscrews and comes apart quickly. I couldn’t find local store with metal spacers and had to order them online (you’d need 11 x 47mm and 3 x 15mm). I think I paid less than USD $10 for all metal parts. Servos This arm uses five standards size servos to drive the arm itself, and two micro servos are used on the gripper. Author of the project used Modelcraft RS-2 Servo and Modelcraft ES-05 HT Servo. I had two Futaba S3001 servos laying around, and ordered additional TowerPro SG-5010 standard size servos and TowerPro SG90 micro servos. However it turned out that the SG90 won’t fit in the gripper so I had to replace it with a slightly smaller E-Sky EK2-0508 micro servo. Later it also turned out that Futaba servos make some strange noise while working so I swapped one with TowerPro SG-5010 which has higher torque (8kg / cm). I’ve also bought three servo extension cables. All servos cost me USD $45. Assembly The build process is not difficult but you need to think carefully about order of assembling it. You can do the base and upper arm first. Because two servos in the base are close together you need to put first with one piece of lower arm already connected before you put the second servo. Then you connect the upper arm and finally put the second piece of lower arm to hold it together. Gripper and base require some gluing so think it through too. Make sure to look closely at all the photos on Thingiverse (also other people copies) and read additional posts on jjshortcust’s blog: My mini servo grippers and completed robotic arm  Multiply the robotic arm and electronics Here is also Rob’s copy cut from aluminum My assembled arm looks like this – I think it turned out really nice: Servo controller board The last piece of hardware I needed was an electronic board that would take command from PC and drive all seven servos. I could probably use Arduino for this task, and in fact there are several Arduino servo shields available (for example from Adafruit or Renbotics).  However one problem is that most support only up to six servos, and second that their accuracy is limited by Arduino’s timer frequency. So instead I looked for dedicated servo controller and found a series of Maestro boards from Pololu. I picked the Pololu Mini Maestro 12-Channel USB Servo Controller. It has many nice features including native USB connection, high resolution pulses (0.25µs) with no jitter, built-in speed and acceleration control, and even scripting capability. Another cool feature is that besides servo control, each channel can be configured as either general input or output. So far I’m using seven channels so I still have five available to connect some sensors (for example distance sensor mounted on gripper might be useful). And last but important factor was that they have SDK in .NET – what more I could wish for! The board itself is very small – half of the size of Tic-Tac box. I picked one for about USD $35 in this store. Perhaps another good alternative would be the Phidgets Advanced Servo 8-Motor – but it is significantly more expensive at USD $87.30. The Maestro Controller Driver and Software package includes Maestro Control Center program with lets you immediately configure the board. For each servo I first figured out their move range and set the min/max limits. I played with setting the speed an acceleration values as well. Big issue for me was that there are two servos that control position of lower arm (shoulder joint), and both have to be moved at the same time. This is where the scripting feature of Pololu board turned out very helpful. I wrote a script that synchronizes position of second servo with first one – so now I only need to move one servo and other will follow automatically. This turned out tricky because I couldn’t find simple offset mapping of the move range for each servo – I had to divide it into several sub-ranges and map each individually. The scripting language is bit assembler-like but gets the job done. And there is even a runtime debugging and stack view available. Altogether I’m very happy with the Pololu Mini Maestro Servo Controller, and with this final piece I completed the build and was able to move my arm from the Meastro Control program.   The total cost of my robotic arm was: $10 laser cut parts $10 metal parts $45 servos $35 servo controller ----------------------- $100 total So here you have all the information about the hardware. In next post I’ll start talking about the software that I wrote in Microsoft Robotics Developer Studio 4. Stay tuned!

  Read the article

• Oracle Flashback Technologies - Overview

  - by Sridhar_R-Oracle

  Oracle Flashback Technologies - IntroductionIn his May 29th 2014 blog, my colleague Joe Meeks introduced Oracle Maximum Availability Architecture (MAA) and discussed both planned and unplanned outages. Let’s take a closer look at unplanned outages. These can be caused by physical failures (e.g., server, storage, network, file deletion, physical corruption, site failures) or by logical failures – cases where all components and files are physically available, but data is incorrect or corrupt. These logical failures are usually caused by human errors or application logic errors. This blog series focuses on these logical errors – what causes them and how to address and recover from them using Oracle Database Flashback. In this introductory blog post, I’ll provide an overview of the Oracle Database Flashback technologies and will discuss the features in detail in future blog posts. Let’s get started. We are all human beings (unless a machine is reading this), and making mistakes is a part of what we do…often what we do best!  We “fat finger”, we spill drinks on keyboards, unplug the wrong cables, etc.  In addition, many of us, in our lives as DBAs or developers, must have observed, caused, or corrected one or more of the following unpleasant events: Accidentally updated a table with wrong values !! Performed a batch update that went wrong - due to logical errors in the code !! Dropped a table !! How do DBAs typically recover from these types of errors? First, data needs to be restored and recovered to the point-in-time when the error occurred (incomplete or point-in-time recovery).  Moreover, depending on the type of fault, it’s possible that some services – or even the entire database – would have to be taken down during the recovery process.Apart from error conditions, there are other questions that need to be addressed as part of the investigation. For example, what did the data look like in the morning, prior to the error? What were the various changes to the row(s) between two timestamps? Who performed the transaction and how can it be reversed?  Oracle Database includes built-in Flashback technologies, with features that address these challenges and questions, and enable you to perform faster, easier, and convenient recovery from logical corruptions. HistoryFlashback Query, the first Flashback Technology, was introduced in Oracle 9i. It provides a simple, powerful and completely non-disruptive mechanism for data verification and recovery from logical errors, and enables users to view the state of data at a previous point in time.Flashback Technologies were further enhanced in Oracle 10g, to provide fast, easy recovery at the database, table, row, and even at a transaction level.Oracle Database 11g introduced an innovative method to manage and query long-term historical data with Flashback Data Archive. The 11g release also introduced Flashback Transaction, which provides an easy, one-step operation to back out a transaction. Oracle Database versions 11.2.0.2 and beyond further enhanced the performance of these features. Note that all the features listed here work without requiring any kind of restore operation.In addition, Flashback features are fully supported with the new multi-tenant capabilities introduced with Oracle Database 12c, Flashback Features Oracle Flashback Database enables point-in-time-recovery of the entire database without requiring a traditional restore and recovery operation. It rewinds the entire database to a specified point in time in the past by undoing all the changes that were made since that time.Oracle Flashback Table enables an entire table or a set of tables to be recovered to a point in time in the past.Oracle Flashback Drop enables accidentally dropped tables and all dependent objects to be restored.Oracle Flashback Query enables data to be viewed at a point-in-time in the past. This feature can be used to view and reconstruct data that was lost due to unintentional change(s) or deletion(s). This feature can also be used to build self-service error correction into applications, empowering end-users to undo and correct their errors.Oracle Flashback Version Query offers the ability to query the historical changes to data between two points in time or system change numbers (SCN) Oracle Flashback Transaction Query enables changes to be examined at the transaction level. This capability can be used to diagnose problems, perform analysis, audit transactions, and even revert the transaction by undoing SQLOracle Flashback Transaction is a procedure used to back-out a transaction and its dependent transactions.Flashback technologies eliminate the need for a traditional restore and recovery process to fix logical corruptions or make enquiries. Using these technologies, you can recover from the error in the same amount of time it took to generate the error. All the Flashback features can be accessed either via SQL command line (or) via Enterprise Manager.  Most of the Flashback technologies depend on the available UNDO to retrieve older data. The following table describes the various Flashback technologies: their purpose, dependencies and situations where each individual technology can be used.   Example Syntax Error investigation related:The purpose is to investigate what went wrong and what the values were at certain points in timeFlashback Queries  ( select .. as of SCN | Timestamp )   - Helps to see the value of a row/set of rows at a point in timeFlashback Version Queries  ( select .. versions between SCN | Timestamp and SCN | Timestamp)  - Helps determine how the value evolved between certain SCNs or between timestamps Flashback Transaction Queries (select .. XID=)   - Helps to understand how the transaction caused the changes.Error correction related:The purpose is to fix the error and correct the problems,Flashback Table  (flashback table .. to SCN | Timestamp)  - To rewind the table to a particular timestamp or SCN to reverse unwanted updates Flashback Drop (flashback table ..  to before drop )  - To undrop or undelete a table Flashback Database (flashback database to SCN  | Restore Point )  - This is the rewind button for Oracle databases. You can revert the entire database to a particular point in time. It is a fast way to perform a PITR (point-in-time recovery). Flashback Transaction (DBMS_FLASHBACK.TRANSACTION_BACKOUT(XID..))  - To reverse a transaction and its related transactions Advanced use cases Flashback technology is integrated into Oracle Recovery Manager (RMAN) and Oracle Data Guard. So, apart from the basic use cases mentioned above, the following use cases are addressed using Oracle Flashback. Block Media recovery by RMAN - to perform block level recovery Snapshot Standby - where the standby is temporarily converted to a read/write environment for testing, backup, or migration purposes Re-instate old primary in a Data Guard environment – this avoids the need to restore an old backup and perform a recovery to make it a new standby. Guaranteed Restore Points - to bring back the entire database to an older point-in-time in a guaranteed way. and so on..I hope this introductory overview helps you understand how Flashback features can be used to investigate and recover from logical errors.  As mentioned earlier, I will take a deeper-dive into to some of the critical Flashback features in my upcoming blogs and address common use cases.

  Read the article

• 10 tape technology features that make you go hmm.

  - by Karoly Vegh

  A week ago an Oracle/StorageTek Tape Specialist, Christian Vanden Balck, visited Vienna, and agreed to visit customers to do techtalks and update them about the technology boom going around tape. I had the privilege to attend some of his sessions and noted the information and features that took the customers by surprise and made them think. Allow me to share the top 10: I. StorageTek as a brand: StorageTek is one of he strongest names in the Tape field. The brand itself was valued so much by customers that even after Sun Microsystems acquiring StorageTek and the Oracle acquiring Sun the brand lives on with all the Oracle tapelibraries are officially branded StorageTek.See http://www.oracle.com/us/products/servers-storage/storage/tape-storage/overview/index.html II. Disk information density limitations: Disk technology struggles with information density. You haven't seen the disk sizes exploding lately, have you? That's partly because there are physical limits on a disk platter. The size is given, the number of platters is limited, they just can't grow, and are running out of physical area to write to. Now, in a T10000C tape cartridge we have over 1000m long tape. There you go, you have got your physical space and don't need to stuff all that data crammed together. You can write in a reliable pattern, and have space to grow too. III. Oracle has a market share of 62% worldwide in recording head manufacturing. That's right. If you are running LTO drives, with a good chance you rely on StorageTek production. That's two out of three LTO recording heads produced worldwide.  IV. You can store 1 Exabyte data in a single tape library. Yes, an Exabyte. That is 1000 Petabytes. Or, a million Terabytes. A thousand million GigaBytes. You can store that in a stacked StorageTek SL8500 tapelibrary. In one SL8500 you can put 10.000 T10000C cartridges, that store 10TB data (compressed). You can stack 10 of these SL8500s together. Boom. 1000.000 TB.(n.b.: stacking means interconnecting the libraries. Yes, cartridges are moved between the stacked libraries automatically.)  V. EMC: 'Tape doesn't suck after all. We moved on.': Do you remember the infamous 'Tape sucks, move on' Datadomain slogan? Of course they had to put it that way, having only had disk products. But here's a fun fact: on the EMCWorld 2012 there was a major presence of a Tape-tech company - EMC, in a sudden burst of sanity is embracing tape again. VI. The miraculous T10000C: Oracle StorageTek has developed an enterprise-grade tapedrive and cartridge, the T10000C. With awesome numbers: The Cartridge: Native 5TB capacity, 10TB with compression Over a kilometer long tape within the cartridge. And it's locked when unmounted, no rattling of your data.  Replaced the metalparticles datalayer with BaFe (bariumferrite) - metalparticles lose around 7% of magnetism within 30 days. BaFe does not. Yes we employ solid-state physicists doing R&D on demagnetisation in our labs. Can be partitioned, storage tiering within the cartridge!  The Drive: 2GB Cache Encryption implemented in HW - no performance hit 252 MB/s native sustained data rate, beats disk technology by far. Not to mention peak throughput.  Leading the tape while never touching the data side of it, protecting your data physically too Data integritiy checking (CRC recalculation) on tape within the drive without having to read it back to the server reordering data from tape-order, delivering it back in application-order  writing 32 tracks at once, reading them back for CRC check at once VII. You only use 20% of your data on a regular basis. The rest 80% is just lying around for years. On continuously spinning disks. Doubly consuming energy (power+cooling), blocking diskstorage capacity. There is a solution called SAM (Storage Archive Manager) that provides you a filesystem unifying disk and tape, moving data on-demand and for clients transparently between the different storage tiers. You can share these filesystems with NFS or CIFS for clients, and enjoy the low TCO of tape. Tapes don't spin. They sit quietly in their slots, storing 10TB data, using no energy, producing no heat, automounted when a client accesses their data.See: http://www.oracle.com/us/products/servers-storage/storage/storage-software/storage-archive-manager/overview/index.html VIII. HW supported for three decades: Did you know that the original PowderHorn library was released in '87 and has been only discontinued in 2010? That is over two decades of supported operation. Tape libraries are - just like the data carrying on tapecartridges - built for longevity. Oh, and the T10000C cartridge has 30-year archival life for long-term retention.  IX. Tape is easy to manage: Have you heard of Tape Storage Analytics? It is a central graphical tool to summarize, monitor, analyze dataflow, health and performance of drives and libraries, see: http://www.oracle.com/us/products/servers-storage/storage/tape-storage/tape-analytics/overview/index.html X. The next generation: The T10000B drives were able to reuse the T10000A cartridges and write on them even more data. On the same cartridges. We call this investment protection, and this is very important for Oracle for the future too. We usually support two generations of cartridges together. The current drive is a T10000C. (...I know I promised to enlist 10, but I got still two more I really want to mention. Allow me to work around the problem: ) X++. The TallBots, the robots moving around the cartridges in the StorageTek library from tapeslots to the drives are cableless. Cables, belts, chains running to moving parts in a library cause maintenance downtimes. So StorageTek eliminated them. The TallBots get power, commands, even firmwareupgrades through the rails they are running on. Also, the TallBots don't just hook'n'pull the tapes out of their slots, they actually grip'n'lift them out. No friction, no scratches, no zillion little plastic particles floating around in the library, in the drives, on your data. (X++)++: Tape beats SSDs and Disks. In terms of throughput (252 MB/s), in terms of TCO: disks cause around 290x more power and cooling, in terms of capacity: 10TB on a single media and soon more.  So... do you need to store large amounts of data? Are you legally bound to archive it for dozens of years? Would you benefit from automatic storage tiering? Have you got large mediachunks to be streamed at times? Have you got power and cooling issues in the growing datacenters? Do you find EMC's 180° turn of tape attitude interesting, but appreciate it at the same time? With all that, you aren't alone. The most data on this planet is stored on tape. Tape is coming. Big time.

  Read the article

• HTG Explains: Should You Buy Extended Warranties?

  - by Chris Hoffman

  Buy something at an electronics store and you’ll be confronted by a pushy salesperson who insists you need an extended warranty. You’ll also see extended warranties pushed hard when shopping online. But are they worth it? There’s a reason stores push extended warranties so hard. They’re almost always pure profit for the store involved. An electronics store may live on razor-thin product margins and make big profits on extended warranties and overpriced HDMI cables. You’re Already Getting Multiple Warranties First, back up. The product you’re buying already includes a warranty. In fact, you’re probably getting several different types of warranties. Store Return and Exchange: Most electronics stores allow you to return a malfunctioning product within the first 15 or 30 days and they’ll provide you with a new one. The exact period of time will vary from store to store. If you walk out of the store with a defective product and have to swap it for a new one within the first few weeks, this should be easy. Manufacturer Warranty: A device’s manufacturer — whether the device is a laptop, a television, or a graphics card — offers their own warranty period. The manufacturer warranty covers you after the store refuses to take the product back and exchange it. The length of this warranty depends on the type of product. For example, a cheap laptop may only offer a one-year manufacturer warranty, while a more expensive laptop may offer a two-year warranty. Credit Card Warranty Extension: Many credit cards offer free extended warranties on products you buy with that credit card. Credit card companies will often give you an additional year of warranty. For example, if you buy a laptop with a two year warranty and it fails in the third year, you could then contact your credit card company and they’d cover the cost of fixing or replacing it. Check your credit card’s benefits and fine print for more information. Why Extended Warranties Are Bad You’re already getting a fairly long warranty period, especially if you have a credit card that offers you a free extended warranty — these are fairly common. If the product you get is a “lemon” and has a manufacturing error, it will likely fail pretty soon — well within your warranty period. The extended warranty matters after all your other warranties are exhausted. In the case of a laptop with a two-year warranty that you purchase with a credit card giving you a one-year warranty extension, your extended warranty will kick in three years after you purchase the laptop. In that many years, your current laptop will likely feel pretty old and laptops that are as good — or better — will likely be pretty cheap. If it’s a television, better television displays will be available at a lower price point. You’ll either want to upgrade to a newer model or you’ll be able to buy a new, just-as-good product for very cheap. You’ll only have to pay out-of-pocket if your device fails after the normal warranty period — in over two or three years for typical laptops purchased with a decent credit card. Save the money you would have spent on the warranty and put it towards a future upgrade. How Much Do Extended Warranties Cost? Let’s look at an example from a typical pushy retail outlet, Best Buy. We went to Best Buy’s website and found a pretty standard $600 Samsung laptop. This laptop comes with a one-year warranty period. If purchased with a fairly common credit card, you can easily get a two-year warranty period on this laptop without spending an additional penny. (Yes, such credit cards are available with no yearly fees.) During the check-out process, Best Buy tries to sell you a Geek Squad “Accidental Protection Plan.” To get an additional year of Best Buy’s extended warranty, you’d have to pay $324.98 for a “3-Year Accidental Protection Plan”. You’d basically be paying more than half the price of your laptop for an additional year of warranty — remember, the standard warranties would cover you anyway for the first two years. If this laptop did break sometime between two and three years from now, we wouldn’t be surprised if you could purchase a comparable laptop for about $325 anyway. And, if you don’t need to replace it, you’ve saved that money. Best Buy would object that this isn’t a standard extended warranty. It’s a supercharged warranty plan that will also provide coverage if you spill something on your laptop or drop it and break it. You just have to ask yourself a question. What are the odds that you’ll drop your laptop or spill something on it? They’re probably pretty low if you’re a typical human being. Is it worth spending more than half the price of the laptop just in case you’ll make an uncommon mistake? Probably not. There may be occasional exceptions to this — some Apple users swear by Apple’s AppleCare, for example — but you should generally avoid buying these things. There’s a reason stores are so pushy about extended warranties, and it’s not because they want to help protect you. It’s because they’re making lots of profit from these plans, and they’re making so much profit because they’re not a good deal for customers. Image Credit: Philip Taylor on Flickr     

  Read the article

• Need help diagnosing network performance issues

  - by tokes

  I am currently working in a developing country as a system analyst for a government department. My area of expertise is software projects, but I've come across a few issues with the network setup in my office. (Unfortunately, being a developing country, there's not a lot of professional help available for this sort of thing.) Most recently, I am trying to diagnose a problem with slowness on the network. Our office is connected to the internet via an ADSL wireless modem/router (called Router). The modem is connected via ethernet to a switch (called Switch). The modem also acts as a wireless access point (called Wireless1), though because it is in a room at the end of the floor, it's range is limited. There are ethernet ports installed around the office. The cables of these all lead back to the same switch. In closer vicinity to the bulk of the client computers, there is another wireless router that acts as an access point for those clients (called Wireless2). That router is connected via ethernet to a wall port, and therefore to Switch. There is also a Windows server which acts as a DNS server (called DNSBox) which is located in the same room and is connected directly to Switch. ---Internet----------| Router/Wireless1 192.168.10.1 ---------------| |----|=========| DNSBox | |-------------------- 192.168.10.4 --------------------| Switch |---Other clients---- | |-------------------- |----|=========| Wireless2 ------------------| 192.168.10.198 One final thing to mention about the network setup. All clients are configured with manual IP addresses. Their router/gateway is set to the IP address of Router, and their DNS server is set to the IP address of DNSBox (with a secondary IP set to an external IP - that of our ISP's DNS server). Here are the symptoms we are experiencing: Clients connected to Wireless2 AP experience slow and unstable connections to the internet. (Slow here is defined as speeds of ~1KB/s, though ping response times seem to be as normal.) Clients connected via ethernet to Switch also experience the same slowness. Clients connected to Wireless1 AP (i.e. connecting via wireless directly to the ADSL modem) experience normal connections to the internet. Clients connected via ethernet to Router (i.e. connecting via ethernet directly to the ADSL modem) also experience normal connections to the internet. I also tried to gauge the connection performance between two machines on the network via ethernet: A file transfer between two clients who were both directly connected to Switch was the fastest; A file transfer between one client directly connected to Switch, and one client directly connected to Router (which is directly connected to Switch) performed much slower; A file transfer between two clients directly connected to Router also performed slowly. Things I have attempted to diagnose the problem: Restarted Switch -- no change. We tried unplugging ethernet jacks from Switch 4 at a time and testing the internet connection. The thought here was that perhaps a client on the network has contracted a virus, and is possibly spamming the network with traffic? (Not very technical, I know.) Unfortunately we couldn't get any significant increases in performance using this method. There were a couple of times when it seemed to be better, but then the connection speed quickly dropped back to slow/dead pace. I didn't want to unplug all jacks from Switch because I was concerned that users might be affected or that I would re-plug in the jacks incorrectly (should I even be worried about that? a port is a port on a switch, right?) I tried swapping the ethernet cable used to connect Router to Switch -- no change in performance. I tried swapping the port used on Switch for Router -- no change in performance. Anyone got any ideas on what this could be? Should I be mentioning specific brand names/models of the hardware used? Virii outbreaks are common in this country/office -- what could I be doing to figure out if a virus is at fault? If it is a virus, it doesn't seem to be generating a lot of traffic to/from the internet, because a) I can still get a good speed if I am directly connected to Router / Wireless1 and b) our ISP data usage has not risen suspiciously. Thanks for your help! Update #1 Here are the specs of some of the hardware: Switch is an Edimax ES3132RL 32-Port 10/100 Rackmount Switch Router is a D-Link DSL-G604T Update #2 I just tried unplugging everything except a laptop and Router from Switch. Speeds are still slow. I guess that means that Router / Switch are not being flooded? It seems more and more likely that the cause is something to do with the interaction between Router and Switch. However, I still can't find any useful resources on setting the LAN speed for either (and I'm not well-versed in these advanced networking configurations).

  Read the article

• What's up with LDoms: Part 1 - Introduction & Basic Concepts

  - by Stefan Hinker

  LDoms - the correct name is Oracle VM Server for SPARC - have been around for quite a while now.  But to my surprise, I get more and more requests to explain how they work or to give advise on how to make good use of them.  This made me think that writing up a few articles discussing the different features would be a good idea.  Now - I don't intend to rewrite the LDoms Admin Guide or to copy and reformat the (hopefully) well known "Beginners Guide to LDoms" by Tony Shoumack from 2007.  Those documents are very recommendable - especially the Beginners Guide, although based on LDoms 1.0, is still a good place to begin with.  However, LDoms have come a long way since then, and I hope to contribute to their adoption by discussing how they work and what features there are today.  In this and the following posts, I will use the term "LDoms" as a common abbreviation for Oracle VM Server for SPARC, just because it's a lot shorter and easier to type (and presumably, read). So, just to get everyone on the same baseline, lets briefly discuss the basic concepts of virtualization with LDoms.  LDoms make use of a hypervisor as a layer of abstraction between real, physical hardware and virtual hardware.  This virtual hardware is then used to create a number of guest systems which each behave very similar to a system running on bare metal:  Each has its own OBP, each will install its own copy of the Solaris OS and each will see a certain amount of CPU, memory, disk and network resources available to it.  Unlike some other type 1 hypervisors running on x86 hardware, the SPARC hypervisor is embedded in the system firmware and makes use both of supporting functions in the sun4v SPARC instruction set as well as the overall CPU architecture to fulfill its function. The CMT architecture of the supporting CPUs (T1 through T4) provide a large number of cores and threads to the OS.  For example, the current T4 CPU has eight cores, each running 8 threads, for a total of 64 threads per socket.  To the OS, this looks like 64 CPUs.  The SPARC hypervisor, when creating guest systems, simply assigns a certain number of these threads exclusively to one guest, thus avoiding the overhead of having to schedule OS threads to CPUs, as do typical x86 hypervisors.  The hypervisor only assigns CPUs and then steps aside.  It is not involved in the actual work being dispatched from the OS to the CPU, all it does is maintain isolation between different guests. Likewise, memory is assigned exclusively to individual guests.  Here,  the hypervisor provides generic mappings between the physical hardware addresses and the guest's views on memory.  Again, the hypervisor is not involved in the actual memory access, it only maintains isolation between guests. During the inital setup of a system with LDoms, you start with one special domain, called the Control Domain.  Initially, this domain owns all the hardware available in the system, including all CPUs, all RAM and all IO resources.  If you'd be running the system un-virtualized, this would be what you'd be working with.  To allow for guests, you first resize this initial domain (also called a primary domain in LDoms speak), assigning it a small amount of CPU and memory.  This frees up most of the available CPU and memory resources for guest domains.  IO is a little more complex, but very straightforward.  When LDoms 1.0 first came out, the only way to provide IO to guest systems was to create virtual disk and network services and attach guests to these services.  In the meantime, several different ways to connect guest domains to IO have been developed, the most recent one being SR-IOV support for network devices released in version 2.2 of Oracle VM Server for SPARC. I will cover these more advanced features in detail later.  For now, lets have a short look at the initial way IO was virtualized in LDoms: For virtualized IO, you create two services, one "Virtual Disk Service" or vds, and one "Virtual Switch" or vswitch.  You can, of course, also create more of these, but that's more advanced than I want to cover in this introduction.  These IO services now connect real, physical IO resources like a disk LUN or a networt port to the virtual devices that are assigned to guest domains.  For disk IO, the normal case would be to connect a physical LUN (or some other storage option that I'll discuss later) to one specific guest.  That guest would be assigned a virtual disk, which would appear to be just like a real LUN to the guest, while the IO is actually routed through the virtual disk service down to the physical device.  For network, the vswitch acts very much like a real, physical ethernet switch - you connect one physical port to it for outside connectivity and define one or more connections per guest, just like you would plug cables between a real switch and a real system. For completeness, there is another service that provides console access to guest domains which mimics the behavior of serial terminal servers. The connections between the virtual devices on the guest's side and the virtual IO services in the primary domain are created by the hypervisor.  It uses so called "Logical Domain Channels" or LDCs to create point-to-point connections between all of these devices and services.  These LDCs work very similar to high speed serial connections and are configured automatically whenever the Control Domain adds or removes virtual IO. To see all this in action, now lets look at a first example.  I will start with a newly installed machine and configure the control domain so that it's ready to create guest systems. In a first step, after we've installed the software, let's start the virtual console service and downsize the primary domain.  root@sun # ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-c-- UART 512 261632M 0.3% 2d 13h 58m root@sun # ldm add-vconscon port-range=5000-5100 \ primary-console primary root@sun # svcadm enable vntsd root@sun # svcs vntsd STATE STIME FMRI online 9:53:21 svc:/ldoms/vntsd:default root@sun # ldm set-vcpu 16 primary root@sun # ldm set-mau 1 primary root@sun # ldm start-reconf primary root@sun # ldm set-memory 7680m primary root@sun # ldm add-config initial root@sun # shutdown -y -g0 -i6 So what have I done: I've defined a range of ports (5000-5100) for the virtual network terminal service and then started that service.  The vnts will later provide console connections to guest systems, very much like serial NTS's do in the physical world. Next, I assigned 16 vCPUs (on this platform, a T3-4, that's two cores) to the primary domain, freeing the rest up for future guest systems.  I also assigned one MAU to this domain.  A MAU is a crypto unit in the T3 CPU.  These need to be explicitly assigned to domains, just like CPU or memory.  (This is no longer the case with T4 systems, where crypto is always available everywhere.) Before I reassigned the memory, I started what's called a "delayed reconfiguration" session.  That avoids actually doing the change right away, which would take a considerable amount of time in this case.  Instead, I'll need to reboot once I'm all done.  I've assigned 7680MB of RAM to the primary.  That's 8GB less the 512MB which the hypervisor uses for it's own private purposes.  You can, depending on your needs, work with less.  I'll spend a dedicated article on sizing, discussing the pros and cons in detail. Finally, just before the reboot, I saved my work on the ILOM, to make this configuration available after a powercycle of the box.  (It'll always be available after a simple reboot, but the ILOM needs to know the configuration of the hypervisor after a power-cycle, before the primary domain is booted.) Now, lets create a first disk service and a first virtual switch which is connected to the physical network device igb2. We will later use these to connect virtual disks and virtual network ports of our guest systems to real world storage and network. root@sun # ldm add-vds primary-vds root@sun # ldm add-vswitch net-dev=igb2 switch-primary primary You are free to choose whatever names you like for the virtual disk service and the virtual switch.  I strongly recommend that you choose names that make sense to you and describe the function of each service in the context of your implementation.  For the vswitch, for example, you could choose names like "admin-vswitch" or "production-network" etc. This already concludes the configuration of the control domain.  We've freed up considerable amounts of CPU and RAM for guest systems and created the necessary infrastructure - console, vts and vswitch - so that guests systems can actually interact with the outside world.  The system is now ready to create guests, which I'll describe in the next section. For further reading, here are some recommendable links: The LDoms 2.2 Admin Guide The "Beginners Guide to LDoms" The LDoms Information Center on MOS LDoms on OTN

  Read the article

• How to mount a blu-ray drive?

  - by Stephan Schielke

  Maybe it is for the best to close this question. This has nothing to do with a bluray drive in general anymore. Probably a hardware defect. I will try to test it with a windows system and different cables again... Thx so far. I have a bluray/dvd/cdrom drive with SATA. Ubuntu wont find it under /dev/sd wodim --devices wodim: Overview of accessible drives (1 found) : ------------------------------------------------------------------------- 0 dev='/dev/sg2' rwrw-- : 'HL-DT-ST' 'BDDVDRW CH08LS10' ------------------------------------------------------------------------- cdrecord -scanbus scsibus2: 2,0,0 200) 'HL-DT-ST' 'BDDVDRW CH08LS10' '2.00' Removable CD-ROM fdisk dont even lists it. Ubuntu only automounts blank DVDs, but neither CDROM nor Blurays. I also changed the sata slot, sata cable and the power cable. The drive works with a windows system. This happens when I try to mount: sudo mount -t auto /dev/scd0 /media/bluray mount: you must specify the filesystem type I tried all filesystems there are. I also installed makemkv. It finds the drive but not the disc. Here is my /dev ls -al /dev total 12 drwxr-xr-x 17 root root 4420 2011-11-25 19:36 . drwxr-xr-x 28 root root 4096 2011-11-25 07:12 .. crw------- 1 root root 10, 235 2011-11-25 19:28 autofs -rw-r--r-- 1 root root 630 2011-11-25 19:28 .blkid.tab -rw-r--r-- 1 root root 630 2011-11-25 19:28 .blkid.tab.old drwxr-xr-x 2 root root 700 2011-11-25 19:27 block drwxr-xr-x 2 root root 100 2011-11-25 19:27 bsg crw------- 1 root root 10, 234 2011-11-25 19:28 btrfs-control drwxr-xr-x 3 root root 60 2011-11-25 19:27 bus drwxr-xr-x 2 root root 3820 2011-11-25 19:28 char crw------- 1 root root 5, 1 2011-11-25 19:28 console lrwxrwxrwx 1 root root 11 2011-11-25 19:28 core -> /proc/kcore drwxr-xr-x 2 root root 60 2011-11-25 19:28 cpu crw------- 1 root root 10, 60 2011-11-25 19:28 cpu_dma_latency drwxr-xr-x 7 root root 140 2011-11-25 19:27 disk crw------- 1 root root 10, 61 2011-11-25 19:28 ecryptfs crw-rw---- 1 root video 29, 0 2011-11-25 19:28 fb0 lrwxrwxrwx 1 root root 13 2011-11-25 19:28 fd -> /proc/self/fd crw-rw-rw- 1 root root 1, 7 2011-11-25 19:28 full crw-rw-rw- 1 root fuse 10, 229 2011-11-25 19:28 fuse crw------- 1 root root 251, 0 2011-11-25 19:28 hidraw0 crw------- 1 root root 251, 1 2011-11-25 19:28 hidraw1 crw------- 1 root root 10, 228 2011-11-25 19:28 hpet lrwxrwxrwx 1 root root 14 2011-11-25 19:27 .initramfs -> /run/initramfs drwxr-xr-x 4 root root 220 2011-11-25 19:28 input crw------- 1 root root 1, 11 2011-11-25 19:28 kmsg srw-rw-rw- 1 root root 0 2011-11-25 19:28 log brw-rw---- 1 root disk 7, 0 2011-11-25 19:28 loop0 brw-rw---- 1 root disk 7, 1 2011-11-25 19:28 loop1 brw-rw---- 1 root disk 7, 2 2011-11-25 19:28 loop2 brw-rw---- 1 root disk 7, 3 2011-11-25 19:28 loop3 brw-rw---- 1 root disk 7, 4 2011-11-25 19:28 loop4 brw-rw---- 1 root disk 7, 5 2011-11-25 19:28 loop5 brw-rw---- 1 root disk 7, 6 2011-11-25 19:28 loop6 brw-rw---- 1 root disk 7, 7 2011-11-25 19:28 loop7 drwxr-xr-x 2 root root 60 2011-11-25 19:27 mapper crw------- 1 root root 10, 227 2011-11-25 19:28 mcelog crw-r----- 1 root kmem 1, 1 2011-11-25 19:28 mem drwxr-xr-x 2 root root 60 2011-11-25 19:27 net crw------- 1 root root 10, 59 2011-11-25 19:28 network_latency crw------- 1 root root 10, 58 2011-11-25 19:28 network_throughput crw-rw-rw- 1 root root 1, 3 2011-11-25 19:28 null crw-rw-rw- 1 root root 195, 0 2011-11-25 19:28 nvidia0 crw-rw-rw- 1 root root 195, 255 2011-11-25 19:28 nvidiactl crw------- 1 root root 1, 12 2011-11-25 19:28 oldmem crw-r----- 1 root kmem 1, 4 2011-11-25 19:28 port crw------- 1 root root 108, 0 2011-11-25 19:28 ppp crw------- 1 root root 10, 1 2011-11-25 19:28 psaux crw-rw-rw- 1 root tty 5, 2 2011-11-25 20:00 ptmx drwxr-xr-x 2 root root 0 2011-11-25 19:27 pts brw-rw---- 1 root disk 1, 0 2011-11-25 19:28 ram0 brw-rw---- 1 root disk 1, 1 2011-11-25 19:28 ram1 brw-rw---- 1 root disk 1, 10 2011-11-25 19:28 ram10 brw-rw---- 1 root disk 1, 11 2011-11-25 19:28 ram11 brw-rw---- 1 root disk 1, 12 2011-11-25 19:28 ram12 brw-rw---- 1 root disk 1, 13 2011-11-25 19:28 ram13 brw-rw---- 1 root disk 1, 14 2011-11-25 19:28 ram14 brw-rw---- 1 root disk 1, 15 2011-11-25 19:28 ram15 brw-rw---- 1 root disk 1, 2 2011-11-25 19:28 ram2 brw-rw---- 1 root disk 1, 3 2011-11-25 19:28 ram3 brw-rw---- 1 root disk 1, 4 2011-11-25 19:28 ram4 brw-rw---- 1 root disk 1, 5 2011-11-25 19:28 ram5 brw-rw---- 1 root disk 1, 6 2011-11-25 19:28 ram6 brw-rw---- 1 root disk 1, 7 2011-11-25 19:28 ram7 brw-rw---- 1 root disk 1, 8 2011-11-25 19:28 ram8 brw-rw---- 1 root disk 1, 9 2011-11-25 19:28 ram9 crw-rw-rw- 1 root root 1, 8 2011-11-25 19:28 random crw-rw-r--+ 1 root root 10, 62 2011-11-25 19:28 rfkill lrwxrwxrwx 1 root root 4 2011-11-25 19:28 rtc -> rtc0 crw------- 1 root root 254, 0 2011-11-25 19:28 rtc0 lrwxrwxrwx 1 root root 3 2011-11-25 19:38 scd0 -> sr0 brw-rw---- 1 root disk 8, 0 2011-11-25 19:28 sda brw-rw---- 1 root disk 8, 1 2011-11-25 19:28 sda1 brw-rw---- 1 root disk 8, 2 2011-11-25 19:28 sda2 brw-rw---- 1 root disk 8, 3 2011-11-25 19:28 sda3 brw-rw---- 1 root disk 8, 5 2011-11-25 19:28 sda5 brw-rw---- 1 root disk 8, 6 2011-11-25 19:28 sda6 brw-rw---- 1 root disk 8, 16 2011-11-25 19:28 sdb brw-rw---- 1 root disk 8, 17 2011-11-25 19:28 sdb1 crw-rw---- 1 root disk 21, 0 2011-11-25 19:28 sg0 crw-rw---- 1 root disk 21, 1 2011-11-25 19:28 sg1 crw-rw----+ 1 root cdrom 21, 2 2011-11-25 19:28 sg2 lrwxrwxrwx 1 root root 8 2011-11-25 19:28 shm -> /run/shm crw------- 1 root root 10, 231 2011-11-25 19:28 snapshot drwxr-xr-x 4 root root 280 2011-11-25 19:28 snd brw-rw----+ 1 root cdrom 11, 0 2011-11-25 19:38 sr0 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stderr -> /proc/self/fd/2 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stdin -> /proc/self/fd/0 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stdout -> /proc/self/fd/1 crw-rw-rw- 1 root tty 5, 0 2011-11-25 19:35 tty crw--w---- 1 root tty 4, 0 2011-11-25 19:28 tty0 crw------- 1 root root 4, 1 2011-11-25 19:28 tty1 crw--w---- 1 root tty 4, 10 2011-11-25 19:28 tty10 crw--w---- 1 root tty 4, 11 2011-11-25 19:28 tty11 crw--w---- 1 root tty 4, 12 2011-11-25 19:28 tty12 crw--w---- 1 root tty 4, 13 2011-11-25 19:28 tty13 crw--w---- 1 root tty 4, 14 2011-11-25 19:28 tty14 crw--w---- 1 root tty 4, 15 2011-11-25 19:28 tty15 crw--w---- 1 root tty 4, 16 2011-11-25 19:28 tty16 crw--w---- 1 root tty 4, 17 2011-11-25 19:28 tty17 crw--w---- 1 root tty 4, 18 2011-11-25 19:28 tty18 crw--w---- 1 root tty 4, 19 2011-11-25 19:28 tty19 crw------- 1 root root 4, 2 2011-11-25 19:28 tty2 crw--w---- 1 root tty 4, 20 2011-11-25 19:28 tty20 crw--w---- 1 root tty 4, 21 2011-11-25 19:28 tty21 crw--w---- 1 root tty 4, 22 2011-11-25 19:28 tty22 crw--w---- 1 root tty 4, 23 2011-11-25 19:28 tty23 crw--w---- 1 root tty 4, 24 2011-11-25 19:28 tty24 crw--w---- 1 root tty 4, 25 2011-11-25 19:28 tty25 crw--w---- 1 root tty 4, 26 2011-11-25 19:28 tty26 crw--w---- 1 root tty 4, 27 2011-11-25 19:28 tty27 crw--w---- 1 root tty 4, 28 2011-11-25 19:28 tty28 crw--w---- 1 root tty 4, 29 2011-11-25 19:28 tty29 crw------- 1 root root 4, 3 2011-11-25 19:28 tty3 crw--w---- 1 root tty 4, 30 2011-11-25 19:28 tty30 crw--w---- 1 root tty 4, 31 2011-11-25 19:28 tty31 crw--w---- 1 root tty 4, 32 2011-11-25 19:28 tty32 crw--w---- 1 root tty 4, 33 2011-11-25 19:28 tty33 crw--w---- 1 root tty 4, 34 2011-11-25 19:28 tty34 crw--w---- 1 root tty 4, 35 2011-11-25 19:28 tty35 crw--w---- 1 root tty 4, 36 2011-11-25 19:28 tty36 crw--w---- 1 root tty 4, 37 2011-11-25 19:28 tty37 crw--w---- 1 root tty 4, 38 2011-11-25 19:28 tty38 crw--w---- 1 root tty 4, 39 2011-11-25 19:28 tty39 crw------- 1 root root 4, 4 2011-11-25 19:28 tty4 crw--w---- 1 root tty 4, 40 2011-11-25 19:28 tty40 crw--w---- 1 root tty 4, 41 2011-11-25 19:28 tty41 crw--w---- 1 root tty 4, 42 2011-11-25 19:28 tty42 crw--w---- 1 root tty 4, 43 2011-11-25 19:28 tty43 crw--w---- 1 root tty 4, 44 2011-11-25 19:28 tty44 crw--w---- 1 root tty 4, 45 2011-11-25 19:28 tty45 crw--w---- 1 root tty 4, 46 2011-11-25 19:28 tty46 crw--w---- 1 root tty 4, 47 2011-11-25 19:28 tty47 crw--w---- 1 root tty 4, 48 2011-11-25 19:28 tty48 crw--w---- 1 root tty 4, 49 2011-11-25 19:28 tty49 crw------- 1 root root 4, 5 2011-11-25 19:28 tty5 crw--w---- 1 root tty 4, 50 2011-11-25 19:28 tty50 crw--w---- 1 root tty 4, 51 2011-11-25 19:28 tty51 crw--w---- 1 root tty 4, 52 2011-11-25 19:28 tty52 crw--w---- 1 root tty 4, 53 2011-11-25 19:28 tty53 crw--w---- 1 root tty 4, 54 2011-11-25 19:28 tty54 crw--w---- 1 root tty 4, 55 2011-11-25 19:28 tty55 crw--w---- 1 root tty 4, 56 2011-11-25 19:28 tty56 crw--w---- 1 root tty 4, 57 2011-11-25 19:28 tty57 crw--w---- 1 root tty 4, 58 2011-11-25 19:28 tty58 crw--w---- 1 root tty 4, 59 2011-11-25 19:28 tty59 crw------- 1 root root 4, 6 2011-11-25 19:28 tty6 crw--w---- 1 root tty 4, 60 2011-11-25 19:28 tty60 crw--w---- 1 root tty 4, 61 2011-11-25 19:28 tty61 crw--w---- 1 root tty 4, 62 2011-11-25 19:28 tty62 crw--w---- 1 root tty 4, 63 2011-11-25 19:28 tty63 crw--w---- 1 root tty 4, 7 2011-11-25 19:28 tty7 crw--w---- 1 root tty 4, 8 2011-11-25 19:28 tty8 crw--w---- 1 root tty 4, 9 2011-11-25 19:28 tty9 crw------- 1 root root 5, 3 2011-11-25 19:28 ttyprintk crw-rw---- 1 root dialout 4, 64 2011-11-25 19:28 ttyS0 crw-rw---- 1 root dialout 4, 65 2011-11-25 19:28 ttyS1 crw-rw---- 1 root dialout 4, 74 2011-11-25 19:28 ttyS10 crw-rw---- 1 root dialout 4, 75 2011-11-25 19:28 ttyS11 crw-rw---- 1 root dialout 4, 76 2011-11-25 19:28 ttyS12 crw-rw---- 1 root dialout 4, 77 2011-11-25 19:28 ttyS13 crw-rw---- 1 root dialout 4, 78 2011-11-25 19:28 ttyS14 crw-rw---- 1 root dialout 4, 79 2011-11-25 19:28 ttyS15 crw-rw---- 1 root dialout 4, 80 2011-11-25 19:28 ttyS16 crw-rw---- 1 root dialout 4, 81 2011-11-25 19:28 ttyS17 crw-rw---- 1 root dialout 4, 82 2011-11-25 19:28 ttyS18 crw-rw---- 1 root dialout 4, 83 2011-11-25 19:28 ttyS19 crw-rw---- 1 root dialout 4, 66 2011-11-25 19:28 ttyS2 crw-rw---- 1 root dialout 4, 84 2011-11-25 19:28 ttyS20 crw-rw---- 1 root dialout 4, 85 2011-11-25 19:28 ttyS21 crw-rw---- 1 root dialout 4, 86 2011-11-25 19:28 ttyS22 crw-rw---- 1 root dialout 4, 87 2011-11-25 19:28 ttyS23 crw-rw---- 1 root dialout 4, 88 2011-11-25 19:28 ttyS24 crw-rw---- 1 root dialout 4, 89 2011-11-25 19:28 ttyS25 crw-rw---- 1 root dialout 4, 90 2011-11-25 19:28 ttyS26 crw-rw---- 1 root dialout 4, 91 2011-11-25 19:28 ttyS27 crw-rw---- 1 root dialout 4, 92 2011-11-25 19:28 ttyS28 crw-rw---- 1 root dialout 4, 93 2011-11-25 19:28 ttyS29 crw-rw---- 1 root dialout 4, 67 2011-11-25 19:28 ttyS3 crw-rw---- 1 root dialout 4, 94 2011-11-25 19:28 ttyS30 crw-rw---- 1 root dialout 4, 95 2011-11-25 19:28 ttyS31 crw-rw---- 1 root dialout 4, 68 2011-11-25 19:28 ttyS4 crw-rw---- 1 root dialout 4, 69 2011-11-25 19:28 ttyS5 crw-rw---- 1 root dialout 4, 70 2011-11-25 19:28 ttyS6 crw-rw---- 1 root dialout 4, 71 2011-11-25 19:28 ttyS7 crw-rw---- 1 root dialout 4, 72 2011-11-25 19:28 ttyS8 crw-rw---- 1 root dialout 4, 73 2011-11-25 19:28 ttyS9 d rwxr-xr-x 3 root root 60 2011-11-25 19:28 .udev crw-r----- 1 root root 10, 223 2011-11-25 19:28 uinput crw-rw-rw- 1 root root 1, 9 2011-11-25 19:28 urandom drwxr-xr-x 2 root root 60 2011-11-25 19:27 usb crw------- 1 root root 252, 0 2011-11-25 19:28 usbmon0 crw------- 1 root root 252, 1 2011-11-25 19:28 usbmon1 crw------- 1 root root 252, 2 2011-11-25 19:28 usbmon2 crw------- 1 root root 252, 3 2011-11-25 19:28 usbmon3 crw------- 1 root root 252, 4 2011-11-25 19:28 usbmon4 crw------- 1 root root 252, 5 2011-11-25 19:28 usbmon5 crw------- 1 root root 252, 6 2011-11-25 19:28 usbmon6 crw------- 1 root root 252, 7 2011-11-25 19:28 usbmon7 crw------- 1 root root 252, 8 2011-11-25 19:28 usbmon8 drwxr-xr-x 4 root root 80 2011-11-25 19:28 v4l crw------- 1 root root 10, 57 2011-11-25 19:28 vboxdrv crw------- 1 root root 10, 56 2011-11-25 19:28 vboxnetctl drwxr-x--- 4 root vboxusers 80 2011-11-25 19:28 vboxusb crw-rw---- 1 root tty 7, 0 2011-11-25 19:28 vcs crw-rw---- 1 root tty 7, 1 2011-11-25 19:28 vcs1 crw-rw---- 1 root tty 7, 2 2011-11-25 19:28 vcs2 crw-rw---- 1 root tty 7, 3 2011-11-25 19:28 vcs3 crw-rw---- 1 root tty 7, 4 2011-11-25 19:28 vcs4 crw-rw---- 1 root tty 7, 5 2011-11-25 19:28 vcs5 crw-rw---- 1 root tty 7, 6 2011-11-25 19:28 vcs6 crw-rw---- 1 root tty 7, 128 2011-11-25 19:28 vcsa crw-rw---- 1 root tty 7, 129 2011-11-25 19:28 vcsa1 crw-rw---- 1 root tty 7, 130 2011-11-25 19:28 vcsa2 crw-rw---- 1 root tty 7, 131 2011-11-25 19:28 vcsa3 crw-rw---- 1 root tty 7, 132 2011-11-25 19:28 vcsa4 crw-rw---- 1 root tty 7, 133 2011-11-25 19:28 vcsa5 crw-rw---- 1 root tty 7, 134 2011-11-25 19:28 vcsa6 crw------- 1 root root 10, 63 2011-11-25 19:28 vga_arbiter crw-rw----+ 1 root video 81, 0 2011-11-25 19:28 video0 crw-rw-rw- 1 root root 1, 5 2011-11-25 19:28 zero sg_scan -i gives me: sudo sg_scan -i /dev/sg0: scsi0 channel=0 id=0 lun=0 [em] ATA ST31000524NS SN12 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg1: scsi0 channel=0 id=1 lun=0 [em] ATA WDC WD15EADS-00S 01.0 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg2: scsi2 channel=0 id=0 lun=0 [em] HL-DT-ST BDDVDRW CH08LS10 2.00 [rmb=1 cmdq=0 pqual=0 pdev=0x5] sg_map gives me: /dev/sg0 /dev/sda /dev/sg1 /dev/sdb /dev/sg2 /dev/scd0 lsscsi -l gives me: [0:0:0:0] disk ATA ST31000524NS SN12 /dev/sda state=running queue_depth=1 scsi_level=6 type=0 device_blocked=0 timeout=30 [0:0:1:0] disk ATA WDC WD15EADS-00S 01.0 /dev/sdb state=running queue_depth=1 scsi_level=6 type=0 device_blocked=0 timeout=30 [2:0:0:0] cd/dvd HL-DT-ST BDDVDRW CH08LS10 2.00 /dev/sr0 state=running queue_depth=1 scsi_level=6 type=5 device_blocked=0 timeout=30 my udf mod is: filename: /lib/modules/3.0.0-14-generic/kernel/fs/udf/udf.ko license: GPL description: Universal Disk Format Filesystem author: Ben Fennema srcversion: 6ABDE012374D96B9685B8E5 depends: crc-itu-t vermagic: 3.0.0-14-generic SMP mod_unload modversions Do I need special drivers or mods enabled? Do I need to change some BIOS settings? edit: Somehow I am now able to fire the mount command without any filesystem errors, but now I get: mount: no medium found on /dev/sr0

  Read the article

• Load-balancing between a Procurve switch and a server

  - by vlad

  Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

  Read the article

• Ubuntu 11.10 - Everytime i am trying to connect to my box using SSH, its failing not connecting

  - by YumYumYum

  From any other PC doing SSH to my Ubuntu 11.10,is failing. Even the SSH is running: Other PC: retrying over and over $ ping 192.168.0.128 PING 192.168.0.128 (192.168.0.128) 56(84) bytes of data. From 192.168.0.226 icmp_seq=1 Destination Host Unreachable From 192.168.0.226 icmp_seq=2 Destination Host Unreachable From 192.168.0.226 icmp_seq=3 Destination Host Unreachable From 192.168.0.226 icmp_seq=4 Destination Host Unreachable $ sudo service iptables stop Stopping iptables (via systemctl): [ OK ] $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] Connection closed by 192.168.0.128 $ ssh [email protected] [email protected]'s password: Connection closed by UNKNOWN $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host Follow up: -- checked cable -- using cable tester and other detectors -- no problem found in cable -- used random 10 cables -- adapter is not broken -- checked it using circuit tester by opening the system (card is new so its not network adapter card problem) -- leds are OK showing -- used LiveCD and did same ping test was having same problem -- disabled ipv6 100% to make sure its not the cause -- disabled iptables 100% so its also not the issue -- some more info $ sudo killall dnsmasq -- did not solved the problem -- -- like many other Q/A was suggesting this same --- $ iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination $ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 $ ssh -vvv [email protected] OpenSSH_5.6p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.0.128 [192.168.0.128] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/sun/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/sun/.ssh/id_rsa type 1 debug1: identity file /home/sun/.ssh/id_rsa-cert type -1 debug1: identity file /home/sun/.ssh/id_dsa type -1 debug1: identity file /home/sun/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 118/256 debug2: bits set: 539/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: match line 139 debug1: Host '192.168.0.128' is known and matches the RSA host key. debug1: Found key in /home/sun/.ssh/known_hosts:139 debug2: bits set: 544/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/sun/.ssh/id_rsa (0x213db960) debug2: key: /home/sun/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/sun/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/sun/.ssh/id_dsa debug3: no such identity: /home/sun/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 60 padlen 4 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). Authenticated to 192.168.0.128 ([192.168.0.128]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env XDG_SESSION_ID debug3: Ignored env HOSTNAME debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE_PID debug3: Ignored env IMSETTINGS_INTEGRATE_DESKTOP debug3: Ignored env GPG_AGENT_INFO debug3: Ignored env TERM debug3: Ignored env HARDWARE_PLATFORM debug3: Ignored env SHELL debug3: Ignored env DESKTOP_STARTUP_ID debug3: Ignored env HISTSIZE debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GJS_DEBUG_OUTPUT debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env QTDIR debug3: Ignored env QTINC debug3: Ignored env GJS_DEBUG_TOPICS debug3: Ignored env IMSETTINGS_MODULE debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE debug3: Ignored env PATH debug3: Ignored env MAIL debug3: Ignored env DESKTOP_SESSION debug3: Ignored env QT_IM_MODULE debug3: Ignored env PWD debug1: Sending env XMODIFIERS = @im=none debug2: channel 0: request env confirm 0 debug1: Sending env LANG = en_US.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env KDE_IS_PRELINKED debug3: Ignored env GDM_LANG debug3: Ignored env KDEDIRS debug3: Ignored env GDMSESSION debug3: Ignored env SSH_ASKPASS debug3: Ignored env HISTCONTROL debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GDL_PATH debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env QTLIB debug3: Ignored env CVS_RSH debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env XDG_RUNTIME_DIR debug3: Ignored env DISPLAY debug3: Ignored env G_BROKEN_FILENAMES debug3: Ignored env COLORTERM debug3: Ignored env XAUTHORITY debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-generic x86_64) * Documentation: https://help.ubuntu.com/ 297 packages can be updated. 92 updates are security updates. New release '12.04 LTS' available. Run 'do-release-upgrade' to upgrade to it. Last login: Fri Jun 8 07:45:15 2012 from 192.168.0.226 sun@SystemAX51:~$ ping 19<--------Lost connection again-------------- Tail follow: -- dmesg is showing a very abnormal logs, like Ubuntu is automatically bringing the eth0 up, where eth0 is getting also auto down. [ 2025.897511] r8169 0000:02:00.0: eth0: link up [ 2029.347649] r8169 0000:02:00.0: eth0: link up [ 2030.775556] r8169 0000:02:00.0: eth0: link up [ 2038.242203] r8169 0000:02:00.0: eth0: link up [ 2057.267801] r8169 0000:02:00.0: eth0: link up [ 2062.871770] r8169 0000:02:00.0: eth0: link up [ 2082.479712] r8169 0000:02:00.0: eth0: link up [ 2285.630797] r8169 0000:02:00.0: eth0: link up [ 2308.417640] r8169 0000:02:00.0: eth0: link up [ 2480.948290] r8169 0000:02:00.0: eth0: link up [ 2824.884798] r8169 0000:02:00.0: eth0: link up [ 3030.022183] r8169 0000:02:00.0: eth0: link up [ 3306.587353] r8169 0000:02:00.0: eth0: link up [ 3523.566881] r8169 0000:02:00.0: eth0: link up [ 3619.839585] r8169 0000:02:00.0: eth0: link up [ 3682.154393] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3899.866854] r8169 0000:02:00.0: eth0: link up [ 4723.978269] r8169 0000:02:00.0: eth0: link up [ 4807.415682] r8169 0000:02:00.0: eth0: link up [ 5101.865686] r8169 0000:02:00.0: eth0: link up How do i fix it? -- http://ubuntuforums.org/showthread.php?t=1959794 -- apt-get install openipml openhpi-plugin-ipml

  Read the article

• Everytime i am trying to connect to my box using SSH, its failing not connecting

  - by YumYumYum

  From any other PC doing SSH to my Ubuntu 11.10,is failing. My network setup: Telenet ISP (Belgium) Fiber cable < RJ45 cable straight to Ubuntu PC Even the SSH is running: Other PC: retrying over and over $ ping 192.168.0.128 PING 192.168.0.128 (192.168.0.128) 56(84) bytes of data. From 192.168.0.226 icmp_seq=1 Destination Host Unreachable From 192.168.0.226 icmp_seq=2 Destination Host Unreachable From 192.168.0.226 icmp_seq=3 Destination Host Unreachable From 192.168.0.226 icmp_seq=4 Destination Host Unreachable $ sudo service iptables stop Stopping iptables (via systemctl): [ OK ] $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] Connection closed by 192.168.0.128 $ ssh [email protected] [email protected]'s password: Connection closed by UNKNOWN $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host Follow up: -- checked cable -- using cable tester and other detectors -- no problem found in cable -- used random 10 cables -- adapter is not broken -- checked it using circuit tester by opening the system (card is new so its not network adapter card problem) -- leds are OK showing -- used LiveCD and did same ping test was having same problem -- disabled ipv6 100% to make sure its not the cause -- disabled iptables 100% so its also not the issue -- some more info $ nmap 192.168.0.128 Starting Nmap 5.50 ( http://nmap.org ) at 2012-06-08 19:11 CEST Nmap scan report for 192.168.0.128 Host is up (0.00045s latency). All 1000 scanned ports on 192.168.0.128 are closed (842) or filtered (158) Nmap done: 1 IP address (1 host up) scanned in 6.86 seconds ubuntu@ubuntu:~$ netstat -aunt | head Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 1 192.168.0.128:58616 74.125.132.99:80 FIN_WAIT1 tcp 0 0 192.168.0.128:56749 199.7.57.72:80 ESTABLISHED tcp 0 1 192.168.0.128:58614 74.125.132.99:80 FIN_WAIT1 tcp 0 0 192.168.0.128:49916 173.194.65.113:443 ESTABLISHED tcp 0 1 192.168.0.128:45699 64.34.119.101:80 SYN_SENT tcp 0 0 192.168.0.128:48404 64.34.119.12:80 ESTABLISHED tcp 0 0 192.168.0.128:54161 67.201.31.70:80 TIME_WAIT $ sudo killall dnsmasq -- did not solved the problem -- -- like many other Q/A was suggesting this same --- $ iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination $ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 $ ssh -vvv [email protected] OpenSSH_5.6p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.0.128 [192.168.0.128] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/sun/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/sun/.ssh/id_rsa type 1 debug1: identity file /home/sun/.ssh/id_rsa-cert type -1 debug1: identity file /home/sun/.ssh/id_dsa type -1 debug1: identity file /home/sun/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 118/256 debug2: bits set: 539/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: match line 139 debug1: Host '192.168.0.128' is known and matches the RSA host key. debug1: Found key in /home/sun/.ssh/known_hosts:139 debug2: bits set: 544/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/sun/.ssh/id_rsa (0x213db960) debug2: key: /home/sun/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/sun/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/sun/.ssh/id_dsa debug3: no such identity: /home/sun/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 60 padlen 4 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). Authenticated to 192.168.0.128 ([192.168.0.128]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env XDG_SESSION_ID debug3: Ignored env HOSTNAME debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE_PID debug3: Ignored env IMSETTINGS_INTEGRATE_DESKTOP debug3: Ignored env GPG_AGENT_INFO debug3: Ignored env TERM debug3: Ignored env HARDWARE_PLATFORM debug3: Ignored env SHELL debug3: Ignored env DESKTOP_STARTUP_ID debug3: Ignored env HISTSIZE debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GJS_DEBUG_OUTPUT debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env QTDIR debug3: Ignored env QTINC debug3: Ignored env GJS_DEBUG_TOPICS debug3: Ignored env IMSETTINGS_MODULE debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE debug3: Ignored env PATH debug3: Ignored env MAIL debug3: Ignored env DESKTOP_SESSION debug3: Ignored env QT_IM_MODULE debug3: Ignored env PWD debug1: Sending env XMODIFIERS = @im=none debug2: channel 0: request env confirm 0 debug1: Sending env LANG = en_US.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env KDE_IS_PRELINKED debug3: Ignored env GDM_LANG debug3: Ignored env KDEDIRS debug3: Ignored env GDMSESSION debug3: Ignored env SSH_ASKPASS debug3: Ignored env HISTCONTROL debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GDL_PATH debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env QTLIB debug3: Ignored env CVS_RSH debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env XDG_RUNTIME_DIR debug3: Ignored env DISPLAY debug3: Ignored env G_BROKEN_FILENAMES debug3: Ignored env COLORTERM debug3: Ignored env XAUTHORITY debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-generic x86_64) * Documentation: https://help.ubuntu.com/ 297 packages can be updated. 92 updates are security updates. New release '12.04 LTS' available. Run 'do-release-upgrade' to upgrade to it. Last login: Fri Jun 8 07:45:15 2012 from 192.168.0.226 sun@SystemAX51:~$ ping 19<--------Lost connection again-------------- Tail follow: -- dmesg is showing a very abnormal logs, like Ubuntu is automatically bringing the eth0 up, where eth0 is getting also auto down. [ 2025.897511] r8169 0000:02:00.0: eth0: link up [ 2029.347649] r8169 0000:02:00.0: eth0: link up [ 2030.775556] r8169 0000:02:00.0: eth0: link up [ 2038.242203] r8169 0000:02:00.0: eth0: link up [ 2057.267801] r8169 0000:02:00.0: eth0: link up [ 2062.871770] r8169 0000:02:00.0: eth0: link up [ 2082.479712] r8169 0000:02:00.0: eth0: link up [ 2285.630797] r8169 0000:02:00.0: eth0: link up [ 2308.417640] r8169 0000:02:00.0: eth0: link up [ 2480.948290] r8169 0000:02:00.0: eth0: link up [ 2824.884798] r8169 0000:02:00.0: eth0: link up [ 3030.022183] r8169 0000:02:00.0: eth0: link up [ 3306.587353] r8169 0000:02:00.0: eth0: link up [ 3523.566881] r8169 0000:02:00.0: eth0: link up [ 3619.839585] r8169 0000:02:00.0: eth0: link up [ 3682.154393] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3899.866854] r8169 0000:02:00.0: eth0: link up [ 4723.978269] r8169 0000:02:00.0: eth0: link up [ 4807.415682] r8169 0000:02:00.0: eth0: link up [ 5101.865686] r8169 0000:02:00.0: eth0: link up How do i fix it? -- http://ubuntuforums.org/showthread.php?t=1959794 $ apt-get install openipml openhpi-plugin-ipml $ openipmish > help redisp_cmd on|off > redisp_cmd on redisp set Final follow up: Step 1: BUG for network card driver r8169 Step 2: get the latest build version http://www.realtek.com/downloads/downloadsView.aspx?Langid=1&PNid=4&PFid=4&Level=5&Conn=4&DownTypeID=3&GetDown=false&Downloads=true#RTL8110SC(L) Step 3: build / make $ cd /var/tmp/driver $ tar xvfj r8169.tar.bz2 $ make clean modules && make install $ rmmod r8169 $ depmod $ cp src/r8169.ko /lib/modules/3.xxxx/kernel/drivers/net/r8169.ko $ modprobe r8169 $ update-initramfs -u $ init 6 Voila!!

  Read the article

• Cross-platform distributed fault-tolerant (disconnected operation/local cache) filesystem

  - by Adrian Frühwirth

  We are facing a design "challenge" where we are required to set up a storage solution with the following properties: What we need HA a scalable storage backend offline/disconnected operation on the client to account for network outages cross-platform access client-side access from certainly Windows (probably XP upwards), possibly Linux backend integrates with AD/LDAP (permission management (user/group management, ...)) should work reasonably well over slow WAN-links Another problem is that we don't really know all possible use cases here, if people need to be able to have concurrent access to shared files or if they will only be accessing their own files, so a possible solution needs to account for concurrent access and how conflict management would look in this case from a user's point of view. This two years old blog posts sums up the impression that I have been getting during the last couple of days of research, that there are lots of current übercool projects implementing (non-Windows) clustered petabyte-capable blob-storage solutions but that there is none that supports disconnected operation nicely and natively, but I am hoping that we have missed an obvious solution. What we have tried OpenAFS We figured that we want a distributed network filesystem with a local cache and tested OpenAFS (which, as the only currently "stable" DFS supporting disconnected operation, seemed the way to go) for a week but there are several problems with it: it's a real pain to set up there are no official RHEL/CentOS packages the package of the current stable version 1.6.5.1 from elrepo randomly kernel panics on fresh installs, this is an absolute no-go Windows support (including the required Kerberos packages) is mystical. The current client for the 1.6 branch does not run on Windows 8, the current client for the 1.7 does but it just randomly crashes. After that experience we didn't even bother testing on XP and Windows 7. Suffice to say, we couldn't get it working and the whole setup has been so unstable and complicated to setup that it's just not an option for production. Samba + Unison Since OpenAFS was a complete disaster and no other DFS seems to support disconnected operation we went for a simpler idea that would sync files against a Samba server using Unison. This has the following advantages: Samba integrates with ADs; it's a pain but can be done. Samba solves the problem of remotely accessing the storage from Windows but introduces another SPOF and does not address the actual storage problem. We could probably stick any clustered FS underneath Samba, but that means we need a HA Samba setup on top of that to maintain HA which probably adds a lot of additional complexity. I vaguely remember trying to implement redundancy with Samba before and I could not silently failover between servers. Even when online, you are working with local files which will result in more conflicts than would be necessary if a local cache were only touched when disconnected It's not automatic. We cannot expect users to manually sync their files using the (functional, but not-so-pretty) GTK GUI on a regular basis. I attempted to semi-automate the process using the Windows task scheduler, but you cannot really do it in a satisfactory way. On top of that, the way Unison works makes syncing against Samba a costly operation, so I am afraid that it just doesn't scale very well or even at all. Samba + "Offline Files" After that we became a little desparate and gave Windows "offline files" a chance. We figured that having something that is inbuilt into the OS would reduce administrative efforts, helps blaming someone else when it's not working properly and should just work since people have been using this for years. Right? Wrong. We really wanted it to work, but it just doesn't. 30 minutes of copying files around and unplugging network cables/disabling network interfaces left us with (silent! there is only a tiny notification in Windows explorer in the statusbar, which doesn't even open Sync Center if you click on it!) undeletable files on the server (!) and conflicts that should not even be conflicts. In the end, we had one successful sync of a tiny text file, everything else just exploded horribly. Beyond that, there are other problems: Microsoft admits that "offline files" in Windows XP cannot cope with "large files" and therefore does not cache/sync them at all which would mean those files become unavailable if the connection drop In Windows 7 the feature is only available in the Professional/Ultimate/Enterprise editions. Summary Unless there is another fault-tolerant DFS that supports Windows natively I assume that stacking a HA Samba cluster on top of something like GlusterFS/Lustre/whatnot is the only option, but I hope that I am wrong here. How do other companies allow fault-tolerant network access to redundant storage in a heterogeneous environment with Windows?

  Read the article

• Web browsing is fast, but downloads are slow

  - by Ricket

  I work for a company on my university's campus, helping with general IT problems and some web development. But lately there has been a problem that has me and my boss completely stumped. We, plus one contractor, make up the entire IT department, so I'm reaching out to you for help. All around the office, we have wall jacks. These collect in a closet down the hall and all plug into a switch. This switch, along with our individual server jacks, plugs into another switch, and that switch plugs into our firewall hardware. Then the firewall is connected out to our campus network. Our campus internet is, well, very fast. I don't know exactly the terms, tiers, etc., but we have thousands of students and downloads can run as fast as 10 MB/s at night; uploads are sometimes even faster. I think we're practically ISP level. In short, I have a lot of faith that it is not the campus side of things that is causing a problem, combined with other evidence I'll mention in a moment. So our symptoms: web browsing is fast. Web pages, images, etc. load instantly. No problems there. But then when I go to download something, the download starts fast but very quickly (a matter of seconds) drops to nearly 0. Often it will actually drop to 0 and time out. This happens with even very small files, 1 MB or less. It smells to me like a QoS sort of thing. I'm not entirely sure, and I wanted to get your opinions first. My boss is hesitant to touch our firewall, much less let me touch it, and it was set up and is managed by a consultant remotely. These problems don't seem tied to a time of the day. I've tried downloads after 5:00 and still the same thing happens. From my desk, I can turn on my wireless adapter and pick up the campus wireless access point. If I unplug ethernet and connect to it, downloads are fast. This adds to my suspicion that it's limited to our company network. Also, a number of weeks ago the consultant upgraded our firewall firmware. Suddenly everything was very fast. I tested with downloads from Sun and speedtest.net and things were blazing fast, as they should be with our campus internet! It was wonderful, and I figured the slow speeds were an old firmware bug. In a matter of days, things steadily declined until they were back to the old symptoms. Oh, and we have antivirus installed on every computer, and we keep it up to date. Though I suppose the possibility is still there that someone could have spyware which is bogging down our internet, in which case what is the easiest/best way to find this out? (maybe this should go in a separate question) Thank you for your patience in reading all of this. Do you have any ideas as to what I can try? Is this something that you've experienced before? What sort of tools or methods can I use to try and diagnose the problem? P.S. everything here is Windows. Windows Server 2003 and 2008 on our servers, and Windows XP on employees' machines. Update: We are submitting a ticket to the university to just take a look and see if they see anything unusual and/or can suggestion methods for us to try and pinpoint our problem. Hopefully they'll be helpful! I'll update this to let you know what goes on. Update again: We found a hub (yes, a HUB) right between our campus connection and our firewall. It had only those two ethernet cables plugged into it, nothing else. After removing the hub, our speeds have jumped up to several mbps. However in talking with the campus, we got them to run a gigabit line to our firewall in place of the 100mbps line. As of friday, we are at about 65 mbps up and down (according to speedtest.net at 8am)!! Go NC State!!

  Read the article

• Sporadic disk clicking sound

  - by Abdó

  Hi, I'm having some unusual and sporadic hard disk clicking issues. Here is a cronological description of the facts. I'm using an ASUS P6T-SE with Intel Core i7, 6Gb RAM 600W Power supply and ATI4670 graphics, running Ubuntu 10.10. About one month ago my hard disk (SATA II Seagate Barracuda 1Tb 7200 rpm) started making a clicking sound: a sort of loud tic-tac, every second or so, when involved in disk activity. The system was clearly slower than before at disk access, but it was functional and I could not find any signal of trouble on the linux logs. I disconnected the disk and tried an older SATA drive I had around: no problem with it. Then I reconnected the Seagate disk, and the problem was mysteriously gone. Ubuntu booted normally, usual speed, no clicking. A couple of weeks later, the problem reappeared. I tried disconnecting reconnecting (as it somehow solved the problem before) without luck. So, despite it was a rather new drive, I assumed it was a hardware issue, made backups and bought a new drive. The new drive is a SATA II Seagate Barracuda 1.5 Tb 7200 rpm. I installed both drives at the same time, with the intention of transferring my files from on to the other. To my surprise, when I booted the computer with both drives, both started making the clicking sound !! Even worse, I removed the old drive, leaving the unformated new drive connected, and booted from a LiveCD. It kept clicking ! Puzzled by this, I tried both drives on my laptop with a SATA to USB cable. At the moment I connected any of them, they made one or two unusual clicks and immediately stopped doing that and worked normally. The old drive I thought almost dead, was working like a charm as if nothing happened. Then I thought: "ok, it must be the motherboard. Let's try again". So, I reconnected the old drive to the ASUS P6T motherboard (the same cables and SATA port as before), and it worked as if nothing happened ! The problem was gone again. The new 1.5 Tb drive was also working ok: No clicking nor slowdown. So I left the old 1Tb disk connected and kept using the computer daily during 3 weeks, until today it happened again. Now I don't really know what to do or check. I'm not even sure if it is a hardware issue any more ! This is rather annoying as it seems it happens with a period of 2 or 3 weeks and I have no means of forcing it to happen. Does anyone have a clue of what can causes this behaviour or have any suggestions of things I should check when it happens again ? What I did today is checking some SMART parameters Error log: smartctl -l error /dev/sda. No errors Short selftest: smartctl -t short /dev/sda. No errors Disk Health check: smartctl -H /dev/sda. passed And here are the vendor specific parameters (smartctl -A /dev/sda) Which I'm not quite sure how to interpret. === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 120 099 006 Pre-fail Always - 235962588 3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 187 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 16348045 9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 3590 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 94 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 097 000 Old_age Always - 4295164029 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 070 057 045 Old_age Always - 30 (Lifetime Min/Max 19/31) 194 Temperature_Celsius 0x0022 030 043 000 Old_age Always - 30 (0 18 0 0) 195 Hardware_ECC_Recovered 0x001a 037 026 000 Old_age Always - 235962588 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 73950746906346 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1832967731 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3294986902 Any clue to this mystery will be really welcome. Thank you very much !!

  Read the article

• Show/hide glossary page in YUI

  - by QLiu

  Hello All, I am trying to develop a toggle function like http://www.lutsr.nl/yui/toggle/ But it works a little different as them. When user enters the glossary page, he sees a full list of Alphabet with all the techical terms explaination All — A | B | C | E | G | H | M | P | Q | R | S | T | U | Z | ActiveSync® Microsoft® ActiveSync est l’ application permettant à un pocket pc d’ échanger des informations avec un ordinateur . Le Pocket PC doit utiliser Microsoft Windows Mobile™ ou Windows CE. Bluetooth® Le Bluetooth permet aux informations d’ être transmises entre les appareils électroniques qui ont le Bluetooth. Si vous utilisez le Bluetooth, vous n'avez pas besoin de connecter les périphériques à l'aide de câbles. ............................. If the user clicks B Alphabet, the rest of content will hide, except B. and B will be move to top of the section. If the user clicks All aplphabet, the whole list will be reset. What I have now, it is able to show/hide and listen to click event. Here is my source code: <a href="#A" class ="toggle" rel="A_section,fade,20"> A</a> | <a href="#B" class ="toggle" rel="B_section,fade,20"> B</a> | Script: //Load JavaScript Ready event. this.toggleLinks=YAHOO.util.Dom.getElementsByClassName("toggle"); for(var i=0; i<this.toggleLinks.length; i++) { YAHOO.util.Event.addListener(this.toggleLinks[i], "click", this.animateElements,this); } toggleElements : function(e,controlNode,refEl) { if(controlNode && refEl) { if(YAHOO.util.Dom.hasClass(refEl,"show")) { YAHOO.util.Dom.removeClass(controlNode,"selected"); YAHOO.util.Dom.removeClass(refEl,"show"); } else { YAHOO.util.Dom.addClass(controlNode,"selected"); YAHOO.util.Dom.addClass(refEl,"show"); } } // to disable control node's default behaviour return false; }, animateElements : function(e,obj) { // obj = javascript toggle object // this = link clicked YAHOO.util.Event.preventDefault(e); if(this.rel) { controlNode = this; } if(typeof(controlNode) == "string") { controlNode = YAHOO.util.Dom.get(controlNode); } // objParameters // [0] = object id // [1] = animation type (fade, slide) // [2] = animation duration (seconds) var linkClicked = this; var objParameters = controlNode.rel.split(","); var refEl = YAHOO.util.Dom.get(objParameters[0]); var objStatus = YAHOO.util.Dom.hasClass(refEl,"show"); // if true, object is shown switchClasses = function() { obj.toggleOtherElements(e,linkClicked,refEl); obj.toggleElements(e,linkClicked,refEl); } if(objParameters[1] == "fade") { if(objStatus == true) { var attributes = { opacity: {from: .999, to: 0} } var objAnim = new YAHOO.util.Anim(objParameters[0],attributes); objAnim.useSeconds = false; objAnim.duration = objParameters[2]; objAnim.onComplete.subscribe(switchClasses); objAnim.animate(); } else { YAHOO.util.Dom.setStyle(objParameters[0],"opacity",0); switchClasses(); var attributes = { opacity: {from: 0, to: .999} } var objAnim = new YAHOO.util.Anim(objParameters[0],attributes); objAnim.useSeconds = false; objAnim.duration = objParameters[2]; objAnim.animate(); } } else if (objParameters[1] == "slide") { // not implemented yet } else { // NO ANIMATION - switch classes switchClasses(); } }, toggleOtherElements : function(e,linkClicked,refEl) { // toggle selected state of other elements pointing to the same source for(var i=0; i<this.toggleLinks.length; i++) { var objParameters = this.toggleLinks[i].rel.split(","); var linkClickedParameters = linkClicked.rel.split(","); if(objParameters[0] == linkClickedParameters[0]) { if(YAHOO.util.Dom.hasClass(this.toggleLinks[i],"selected")) { YAHOO.util.Dom.removeClass(this.toggleLinks[i],"selected"); } else { YAHOO.util.Dom.addClass(this.toggleLinks[i],"selected"); } } } }

  Read the article

• Help to argue why to develop software on a physical computer rather than via a remote desktop

  - by s5804

  Remote desktops are great and many times a blessing and cost effective (instead of leasing expensive cables). I am not arguing against remote desktops, just if one have the alternative to use either remote desktop or physical computer, I would choose the later. Also note that I am not arguing for or against remote work practices. But in my case I am required to be physically present in the office when developing software. Background, I work in a company which main business is not to develop software. Therefore the company IT policies are mainly focused on security and to efficiently deploying/maintaing thousands of computer to users. Further, the typical employee runs typical Office applications, like a word processors. Because safety/stability is such a big priority, every non production system/application, shall be deployed into a physical different network, called the test network. Software development of course also belongs in the test network. To access the test network the company has created a standard policy, which dictates that access to the test network shall go only via a remote desktop client. Practically from ones production computer one would open up a remote desktop client to a virtual computer located in the test network. On the virtual computer's remote desktop one would be able to access/run/install all development tools, like Eclipse IDE. Another solution would be to have a dedicated physical computer, which is physically only connected to the test network. Both solutions are available in the company. I have tested both approaches and found running Eclipse IDE, SQL developer, in the remote desktop client to be sluggish (keyboard strokes are delayed), commands like alt-tab takes me out of the remote client, enjoying... Further, screen resolution and colors are different, just to mention a few. Therefore there is nothing technical wrong with the remote client, just not optimal and frankly de-motivating. Now with the new policies put in place, plans are to remove the physical computers connected to the test network. I am looking for help to argue for why software developers shall have a dedicated physical software development computer, to be productive and cost effective. Remember that we are physically in office. Further one can notice that we are talking about approx. 50 computers out of 2000 employees. Therefore the extra budget is relatively small. This is more about policy than cost. Please note that there are lots of similar setups in other companies that work great due to a perfectly tuned systems. However, in my case it is sluggish and it would cost more money to trouble shoot the performance and fine tune it rather than to have a few physical computers. As a business case we have argued that productivity will go down by 25%, however it's my feeling that the reality is probably closer to 50%. This business case isn't really accepted and I find it very difficult to defend it to managers that has never ever used a rich IDE in their life, never mind developed software. Further the test network and remote client has no guaranteed service level, therefore it is down for a few hours per month with the lowest priority on the fix list. Help is appreciated.

  Read the article

< Previous Page | 16 17 18 19 20 21  | Next Page >