Search Results

Search found 729 results on 30 pages for 'inet'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 20/30 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

  • Diagnosing packet loss / high latency in Ubuntu

    - by Sam Gammon
    We have a Linux box (Ubuntu 12.04) running Nginx (1.5.2), which acts as a reverse proxy/load balancer to some Tornado and Apache hosts. The upstream servers are physically and logically close (same DC, sometimes same-rack) and show sub-millisecond latency between them: PING appserver (10.xx.xx.112) 56(84) bytes of data. 64 bytes from appserver (10.xx.xx.112): icmp_req=1 ttl=64 time=0.180 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=2 ttl=64 time=0.165 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=3 ttl=64 time=0.153 ms We receive a sustained load of about 500 requests per second, and are currently seeing regular packet loss / latency spikes from the Internet, even from basic pings: sam@AM-KEEN ~> ping -c 1000 loadbalancer PING 50.xx.xx.16 (50.xx.xx.16): 56 data bytes 64 bytes from loadbalancer: icmp_seq=0 ttl=56 time=11.624 ms 64 bytes from loadbalancer: icmp_seq=1 ttl=56 time=10.494 ms ... many packets later ... Request timeout for icmp_seq 2 64 bytes from loadbalancer: icmp_seq=2 ttl=56 time=1536.516 ms 64 bytes from loadbalancer: icmp_seq=3 ttl=56 time=536.907 ms 64 bytes from loadbalancer: icmp_seq=4 ttl=56 time=9.389 ms ... many packets later ... Request timeout for icmp_seq 919 64 bytes from loadbalancer: icmp_seq=918 ttl=56 time=2932.571 ms 64 bytes from loadbalancer: icmp_seq=919 ttl=56 time=1932.174 ms 64 bytes from loadbalancer: icmp_seq=920 ttl=56 time=932.018 ms 64 bytes from loadbalancer: icmp_seq=921 ttl=56 time=6.157 ms --- 50.xx.xx.16 ping statistics --- 1000 packets transmitted, 997 packets received, 0.3% packet loss round-trip min/avg/max/stddev = 5.119/52.712/2932.571/224.629 ms The pattern is always the same: things operate fine for a while (<20ms), then a ping drops completely, then three or four high-latency pings (1000ms), then it settles down again. Traffic comes in through a bonded public interface (we will call it bond0) configured as such: bond0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5d inet addr:50.xx.xx.16 Bcast:50.xx.xx.31 Mask:255.255.255.224 inet6 addr: <ipv6 address> Scope:Global inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:527181270 errors:1 dropped:4 overruns:0 frame:1 TX packets:413335045 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240016223540 (240.0 GB) TX bytes:104301759647 (104.3 GB) Requests are then submitted via HTTP to upstream servers on the private network (we can call it bond1), which is configured like so: bond1 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5c inet addr:10.xx.xx.70 Bcast:10.xx.xx.127 Mask:255.255.255.192 inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:430293342 errors:1 dropped:2 overruns:0 frame:1 TX packets:466983986 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:77714410892 (77.7 GB) TX bytes:227349392334 (227.3 GB) Output of uname -a: Linux <hostname> 3.5.0-42-generic #65~precise1-Ubuntu SMP Wed Oct 2 20:57:18 UTC 2013 x86_64 GNU/Linux We have customized sysctl.conf in an attempt to fix the problem, with no success. Output of /etc/sysctl.conf (with irrelevant configs omitted): # net: core net.core.netdev_max_backlog = 10000 # net: ipv4 stack net.ipv4.tcp_ecn = 2 net.ipv4.tcp_sack = 1 net.ipv4.tcp_fack = 1 net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_timestamps = 1 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_max_syn_backlog = 10000 net.ipv4.tcp_congestion_control = cubic net.ipv4.ip_local_port_range = 8000 65535 net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_thin_dupack = 1 net.ipv4.tcp_thin_linear_timeouts = 1 net.netfilter.nf_conntrack_max = 99999999 net.netfilter.nf_conntrack_tcp_timeout_established = 300 Output of dmesg -d, with non-ICMP UFW messages suppressed: [508315.349295 < 19.852453>] [UFW BLOCK] IN=bond1 OUT= MAC=<mac addresses> SRC=118.xx.xx.143 DST=50.xx.xx.16 LEN=68 TOS=0x00 PREC=0x00 TTL=51 ID=43221 PROTO=ICMP TYPE=3 CODE=1 [SRC=50.xx.xx.16 DST=118.xx.xx.143 LEN=40 TOS=0x00 PREC=0x00 TTL=249 ID=10220 DF PROTO=TCP SPT=80 DPT=53817 WINDOW=8190 RES=0x00 ACK FIN URGP=0 ] [517787.732242 < 0.443127>] Peer 190.xx.xx.131:59705/80 unexpectedly shrunk window 1155488866:1155489425 (repaired) How can I go about diagnosing the cause of this problem, on a Debian-family Linux box?

    Read the article

  • Dhcpd Daemon is trying to lease itself?

    - by tommieb75
    I have a Slackware Linux 13.0 box with two interfaces, eth0 and eth1. I have set this box up to be on the 192.168.1.0/24 network, with subnet mask of 255.255.255.0. I am trying to run a dhcpd server on this box to service two interfaces above, so I subnetted the 192.168.1.0/24 network into two subnets. For eth0 192.168.1.1, subnet mask 255.255.255.128, broadcast mask 192.168.1.127. For eth1 192.168.1.129, subnet mask 255.255.255.128, broadcast mask 192.168.1.255. Both the interfaces are assigned manually. eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.1.1 Bcast:192.168.1.127 Mask:255.255.255.128 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:39 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1404 (1.3 KiB) Interrupt:11 Base address:0x8000 Memory:faffc000-faffcfff eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.1.128 Bcast:192.168.1.255 Mask:255.255.255.128 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10003 errors:0 dropped:0 overruns:0 frame:0 TX packets:13286 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1589229 (1.5 MiB) TX bytes:9900005 (9.4 MiB) Interrupt:11 Here is the dhcpd.conf set up authoritative; ddns-update-style interim; ignore client-updates; subnet 192.168.1.0 netmask 255.255.255.128 { range 192.168.1.2 192.168.1.126; default-lease-time 86400; max-lease-time 86400; option routers 192.168.1.1; option ip-forwarding off; option domain-name-servers 208.67.222.222, 208.67.220.220; option broadcast-address 192.168.1.127; option subnet-mask 255.255.255.128; } subnet 192.168.1.128 netmask 255.255.255.128 { range 192.168.1.129 192.168.1.254; default-lease-time 86400; max-lease-time 86400; option routers 192.168.1.1; option ip-forwarding off; option domain-name-servers 208.67.222.222, 208.67.220.220; option broadcast-address 192.168.1.255; option subnet-mask 255.255.255.128; } This is what is showing in the log Apr 10 18:09:58 inspiron8600 dhcpd: DHCPDISCOVER from 00:00:00:00:00:00 (inspiron8600) via eth1 Apr 10 18:09:58 inspiron8600 dhcpd: DHCPOFFER on 192.168.1.131 to 00:00:00:00:00:00 (inspiron8600) via eth1 Apr 10 18:10:01 inspiron8600 dhcpcd[3832]: eth1: adding IP address 169.254.153.6/16 This is happening spuriously, and the log gets filled up with nonsense..so my question is this: How do I stop this from happening? And why would it be trying to give itself a lease? I am sure I have missed something but cannot see it and would appreciate a pair of eyes from the community to spot the obvious flaw!

    Read the article

  • wireless internet in linux is very very slow... but in windows.... everythnings fine

    - by Cody Acer
    yesterday when i was connecting to our neighbors wifi connection which is the signal strength is below 50%, i cant browse anything... even ping to gateway. 100% packet loss, and sometimes.. i can connect awesomely i can open my facebook account for 15 minutes but after 15min.. connection is extremely slow. but not windows i can surf even the signal str is very poor weird ey??.. root@Emely:~# lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge [8086:a010] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a011] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller [0380]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a012] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel modules: i2c-i801 05:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: bcma-pci-bridge Kernel modules: bcma 09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: sky2 Kernel modules: sky2 root@Emely:~# ip addr show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff inet 192.168.1.108/24 brd 192.168.1.255 scope global wlan0 inet6 fe80::21b:b1ff:fea9:ace0/64 scope link valid_lft forever preferred_lft forever root@Emely:~# ip link show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff root@Emely:~# rfkill list all 0: samsung-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: samsung-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no 3: phy0: Wireless LAN Soft blocked: no Hard blocked: no is this a wireless driver issue?

    Read the article

  • unable to sniff traffic despite network interface being in monitor or promiscuous mode

    - by user65126
    I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

    Read the article

  • Bonding: works only for download

    - by Crazy_Bash
    I would like to install bonding with 4 links with mode 4. but only "download/receiving" works with bondig. for transmitting the system chooses one link. ifconfig bond0 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 inet addr:ip Bcast:ip Mask:255.255.255.248 inet6 addr: fe80::92e2:baff:fe0f:76b4/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:239187413 errors:0 dropped:10944 overruns:0 frame:0 TX packets:536902370 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14688536197 (13.6 GiB) TX bytes:799521192901 (744.6 GiB) eth2 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:54969488 errors:0 dropped:0 overruns:0 frame:0 TX packets:2537 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3374778591 (3.1 GiB) TX bytes:314290 (306.9 KiB) eth3 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:64935805 errors:0 dropped:1 overruns:0 frame:0 TX packets:2532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3993499746 (3.7 GiB) TX bytes:313968 (306.6 KiB) eth4 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:57352105 errors:0 dropped:2 overruns:0 frame:0 TX packets:536894778 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3524236530 (3.2 GiB) TX bytes:799520265627 (744.6 GiB) eth5 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:61930025 errors:0 dropped:3 overruns:0 frame:0 TX packets:2540 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3796021948 (3.5 GiB) TX bytes:314274 (306.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5320 (5.1 KiB) TX bytes:5320 (5.1 KiB) those are my configs: DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2 (0) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 802.3ad info LACP rate: slow Aggregator selection policy (ad_select): stable Active Aggregator Info: Aggregator ID: 1 Number of ports: 4 Actor Key: 17 Partner Key: 11 Partner Mac Address: 00:24:51:12:63:00 Slave Interface: eth2 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b4 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b5 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b6 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b7 Aggregator ID: 1 Slave queue ID: 0 /etc/modprobe.d/bonding.conf alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 Linux: Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux what i've tried: downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 mode 6

    Read the article

  • vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

    - by kce
    I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

    Read the article

  • OpenVPN - client-to-client traffic working in one direction but not the other

    - by user42055
    I have the following VPN configuration: +------------+ +------------+ +------------+ | outpost |----------------| kino |----------------| guchuko | +------------+ +------------+ +------------+ OS: FreeBSD 6.2 OS: Gentoo 2.6.32 OS: Gentoo 2.6.33.3 Keyname: client3 Keyname: server Keyname: client1 eth0: 10.0.1.254 eth0: 203.x.x.x eth0: 192.168.0.6 tun0: 192.168.150.18 tun0: 192.168.150.1 tun0: 192.168.150.10 P-t-P: 192.166.150.17 P-t-P: 192.168.150.2 P-t-P: 192.168.150.9 Kino is the server and has client-to-client enabled. All three machines have ip forwarding enabled, by this on the gentoo boxes: net.ipv4.conf.all.forwarding = 1 And this on the FreeBSD box: net.inet.ip.forwarding: 1 In the server's "ccd" directory is the following files: client1: iroute 192.168.0.0 255.255.255.0 client3: iroute 10.0.1.0 255.255.255.0 The server config has these routes configured: push "route 192.168.0.0 255.255.255.0" push "route 10.0.1.0 255.255.255.0" route 192.168.0.0 255.255.255.0 route 10.0.1.0 255.255.255.0 Kino's routing table looks like this: 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Outpost's like this: 192.168.150 192.168.150.17 UGS 0 17 tun0 192.168.0 192.168.150.17 UGS 0 2 tun0 192.168.150.17 192.168.150.18 UH 3 0 tun0 And Guchuko's like this: 192.168.150.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Now, the tests. Pings from Guchuko to Outpost's LAN IP work OK, as does the reverse - pings from Outpost to Guchuko's LAN IP. However... Pings from Outpost, to a machine on Guchuko's LAN work fine: .(( root@outpost )). (( 06:39 PM )) :: ~ :: # ping 192.168.0.3 PING 192.168.0.3 (192.168.0.3): 56 data bytes 64 bytes from 192.168.0.3: icmp_seq=0 ttl=63 time=462.641 ms 64 bytes from 192.168.0.3: icmp_seq=1 ttl=63 time=557.909 ms But a ping from Guchuko, to a machine on Outpost's LAN does not: .(( root@guchuko )). (( 06:43 PM )) :: ~ :: # ping 10.0.1.253 PING 10.0.1.253 (10.0.1.253) 56(84) bytes of data. --- 10.0.1.253 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2000ms Guchuko's tcpdump of tun0 shows: 18:46:27.716931 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 1, length 64 18:46:28.716715 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 2, length 64 18:46:29.716714 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 Outpost's tcpdump on tun0 shows: 18:44:00.333341 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 18:44:01.334073 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 4, length 64 18:44:02.331849 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 5, length 64 So Outpost is receiving the ICMP request destined for the machine on it's subnet, but appears not be forwarding it. Outpost has gateway_enable="YES" in its rc.conf which correctly sets net.inet.ip.forwarding to 1 as mentioned earlier. As far as I know, that's all that's required to make a FreeBSD box forward packets between interfaces. Is there something else I could be forgetting ?

    Read the article

  • Specifying a Postfix Instance to send outbound email

    - by Catherine Jefferson
    I have a CentOS 6.5 server running Postfix 2.6x (the default distribution) with five public IPv4 IPs bound to it. Each IP has DNS and rDNS set separately. Each uses a different hostname at a different domain. I have five Postfix instances, one bound to each IP, like this example: 192.168.34.104 red.example.com /etc/postfix 192.168.36.48 green.example.net /etc/postfix-green 192.168.36.49 pink.example.org /etc/postfix-pink 192.168.36.50 orange.example.info /etc/postfix-orange 192.168.36.51 blue.example.us /etc/postfix-blue I've tested each IP by telneting to port 25. Postfix answers and banners properly with the correct hostname. Email is received on all of these instances with no problems and is routed to the correct place. This setup, minus the final instance, has existed for a couple of years and works. I never bothered to set up outbound email to go through any but the main instance, however; there was no need. Now I need to send email from blue.example.us that actually leaves from that interface and IP, such that the Received headers show blue.example.us as the sending mailhost, so that SPF and DKIM validate, etc etc. The email that will be sent from blue.example.com is a feedback loop sent by a single shell account on the server (account5), an account that is dedicated to sending this email. The account receives the feedback loop emails from servers on other networks, saves the bodies of those emails, and then generates a new outbound email header, appends the saved body, and sends the email. It's sending by piping each email to sendmail -oi -t. We're doing it this way to mask the identities of the initial servers. The procmail script that processes these emails works correctly. However, I cannot configure this account to send email through the proper Postfix instance/IP/interface. The exact same account and script sends email through the main Postfix instance /etc/postfix without any issues. When I change MAIL_CONFIG to point to /etc/postfix-blue in either .bash_profile or the Procmail script that handles this email, though, I get this error: sendmail: fatal: User account5(###) is not allowed to submit mail I've read the manuals on Postfix.org, searched Google, and tried the suggestions in three previous answers here on ServerFault.com: Postfix - specify interface to deliver outbound mail on Postfix user is not allowed to submit mail Postfix rejects php mails I have been careful to stop and restart Postfix after each configuration change, and tested the results. Nothing has worked. The main postfix instance happily accepts outbound email from account5. The postfix-blue instance continues to reject email from account5 with the sendmail error above. As tempting as it is to blame machine hostility, I know that I must be missing something or doing something wrong. Does anybody have any suggestions as to what it might be? Please feel free to ask for further information about my setup if you need it. =-=-=-=-=-=-=-=-=-= At the request of the responder, here are main.cf and master.cf for a) the main postfix instance ("red.example.com") and b) the FBL instance ("blue.example.us") [NOTE: All parameters not specified below were left at the default Postfix 2.6 settings] MAIN: master.cf smtp inet n - n - - smtpd main.cf myhostname = red.example.com mydomain = example.com inet_interfaces = $myhostname, localhost inet_protocols = all lmtp_host_lookup = native smtp_host_lookup = native ignore_mx_lookup_error = yes mydestination = $myhostname, localhost.$mydomain, localhost local_recipient_maps = mynetworks = 192.168.34.104/32 relay_domains = example.com, example.info, example.net, example.org, example.us relayhost = [192.168.34.102] # Separate physical server, main mailserver. relay_recipient_maps = hash:/etc/postfix/relay_recipients alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases smtpd_banner = $myhostname ESMTP $mail_name multi_instance_wrapper = ${command_directory}/postmulti -p -- multi_instance_enable = yes multi_instance_directories = /etc/postfix-green /etc/postfix-pink /etc/postfix-orange /etc/postfix-blue FBL: master.cf 184.173.119.103:25 inet n - n - - smtpd main.cf myhostname = blue.example.us mydomain = blue.example.us <= Deliberately set to subdomain only. myorigin = $mydomain inet_interfaces = $myhostname lmtp_host_lookup = native smtp_host_lookup = native ignore_mx_lookup_error = yes mydestination = $myhostname local_recipient_maps = unix:passwd.byname $alias_maps $virtual_alias_maps mynetworks = 192.168.36.51/32, 192.168.35.20/31 <= Second IP is backup MX servers relay_domains = $mydestination recipient_canonical_maps = hash:/etc/postfix-blue/canonical virtual_alias_maps = hash:/etc/postfix-fbl/virtual alias_maps = hash:/etc/aliases, hash:/etc/postfix-blue/canonical alias_maps = hash:/etc/aliases, hash:/etc/postfix-blue/canonical mailbox_command = /usr/bin/procmail -a "$EXTENSION" DEFAULT=$HOME/Mail/ MAILDIR=$HOME/Mail smtpd_banner = $myhostname ESMTP $mail_name authorized_submit_users = multi_instance_name = postfix-blue multi_instance_enable = yes

    Read the article

  • Setting up home DNS with Ubuntu Server

    - by Zeophlite
    I have a webserver (with static IP 192.168.1.5), and I want to have my machines on my local network to be able to access it without modifying /etc/hosts (or equivalent for Windows/OSX). My router has Primary DNS server 192.168.1.5 Secondary DNS server 8.8.8.8 (Google's public DNS). Nginx is set up to server websites externally as *.example.com Internally, I want *.example.local to point to the server. My webserver has BIND9 installed, but I'm unsure of the settings. I've been through various contradicting tutorials, and so most of my settings have been clobbered. I've stripped out the lines which I'm confused about. The tutorials I looked at are http://tech.surveypoint.com/blog/installing-a-local-dns-server-behind-a-hardware-router/ and http://ubuntuforums.org/showthread.php?t=236093 . They mostly differ on what should be put in /etc/bind/zones/db.example.local and /etc/bind/zones/db.192, so I've left the conflicting lines out below. Can someone suggest what the correct lines are to give my above behaviour (namely *.example.local pointing to 192.168.1.5)? /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.5 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.254 /etc/hostname avalon /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN /etc/bind/named.conf.options options { directory "/var/cache/bind"; forwarders { 8.8.8.8; 8.8.4.4; }; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.local zone "example.local" { type master; file "/etc/bind/zones/db.example.local"; }; zone "1.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/db.192"; }; /etc/bind/zones/db.example.local $TTL 604800 @ IN SOA avalon.example.local. webadmin.example.local. ( 5 ; Serial, increment each edit 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL /etc/bind/zones/db.192 $TTL 604800 @ IN SOA avalon.example.local. webadmin.example.local. ( 4 ; Serial, increment each edit 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; What do I need to add to the above files so that on a laptop on the internal network, I can type in webapp.example.local, and be served by my webserver? EDIT I made several changes to the above files on the webserver. /etc/network/interfaces (end of file) dns-nameservers 127.0.0.1 dns-search example.local /etc/bind/zones/db.example.local (end of file) @ IN NS avalon.example.local. @ IN A 192.168.1.5 avalon IN A 192.168.1.5 webapp IN A 192.168.1.5 www IN CNAME 192.168.1.5 /etc/bind/zones/db.192 (end of file) IN NS avalon.example.local. 73 IN PTR avalon.example.local. As a side note, my spare Win7 machine was able to connect directly to webapp.example.local, but for a Ubuntu 13.10 machine, I had to make the following changes as well (not on the webserver, but on a separate machine): /etc/nsswitch.conf before hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 after hosts: files dns /etc/NetworkManager/NetworkManager.conf before dns=dnsmasq after #dns=dnsmasq The issue remains that its not wildcard DNS, and so I have to add entries to /etc/bind/zones/db.example.local for webapp1, webapp2, ...

    Read the article

  • Set source address to use tun device does not work (Debian Squeeze)

    - by A. Donda
    there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

    Read the article

  • Wireless networking on Gnome on Ubuntu 9 / 10

    - by WaveyDavey
    So here's my problem: I have some netbooks (ASUS eee, and ACER Aspire Ones) that I've been tasked to set up as kiosk machines, locked up tight for normal users. I am a command-line, server man, so this gnome malarkey is all a bit new to me. I found a lovely 9.04 kiosk livecd that installs and runs exactly as I want it to, but I can't get the wireless working. So I dropped on a full 10.4 distro, and wireless works straight out of the box (so hardware is good) - all I needed to do was right-click on the network connection icon, enter my SSID and password (WPA/WPA2) and away it went, perfect. Further investigation on 10.4 distro shows that /etc/networking/interfaces is virtually empty (just auto lo iface lo inet loopback in it), even after I have set up the wireless thru the gnome taskbar applet (is that the right word?). So where does gnome / ubuntu store the network settings to bring the blasted wireless connection up, and what do I need to do on the kiosk version to get wireless running?

    Read the article

  • Davicom Semiconductor, Inc. 21x4x DEC-Tulip not detected by Wireshark but IP operational

    - by deepsix86
    Recently flipped to Ubuntu 11.10 on a Dell 4300 (Intel). Getting IP address and no issues (ping/surf) but Wireshark unable to detect eth0 interface. I see references in forums to blacklist tulip but looks like I am running dmfe. Not sure if the blacklist is required and where to go from here. Maybe Driver update? Got a little lost looking in that area. Some h/w details below (IP/MAC/HOSTNAME removed) Linux xxxxxx 3.0.0-17-generic #30-Ubuntu SMP Thu Mar 8 17:34:21 UTC 2012 i686 i686 i386 GNU/Linux network-admin (HOSTS TAB) does not list eth0, only loopback and bunch of IPv6 interfaces ifconfig eth0 Link encap:Ethernet HWaddr xxxxxxxx inet addr:192.168.x.xx Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: xxxxxxxxxxx 64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36662 errors:0 dropped:1 overruns:0 frame:0 TX packets:24975 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:42115779 (42.1 MB) TX bytes:3056435 (3.0 MB) Interrupt:18 Base address:0xe800 lspci 02:09.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) Subsystem: Device 4554:434e Flags: bus master, medium devsel, latency 64, IRQ 18 I/O ports at e800 [size=256] Memory at fe1ffc00 (32-bit, non-prefetchable) [size=256] Expansion ROM at fe200000 [disabled] [size=256K] Capabilities: [50] Power Management version 2 Kernel driver in use: dmfe Kernel modules: dmfe hwinfo --netcard 20: PCI 209.0: 0200 Ethernet controller [Created at pci.318] Unique ID: rBUF.0NgK5ZS9c0D Parent ID: 6NW+.siohrLUzzI4 SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:09.0 SysFS BusID: 0000:02:09.0 Hardware Class: network Model: "Davicom 21x4x DEC-Tulip compatible 10/100 Ethernet" Vendor: pci 0x1282 "Davicom Semiconductor, Inc." Device: pci 0x9102 "21x4x DEC-Tulip compatible 10/100 Ethernet" SubVendor: pci 0x4554 SubDevice: pci 0x434e Revision: 0x31 Driver: "dmfe" Driver Modules: "dmfe" Device File: eth0 I/O Ports: 0xe800-0xe8ff (rw) Memory Range: 0xfe1ffc00-0xfe1ffcff (rw,non-prefetchable) Memory Range: 0xfe200000-0xfe23ffff (ro,non-prefetchable,disabled) IRQ: 18 (61379 events) HW Address: 00:08:a1:01:35:70 Link detected: yes Module Alias: "pci:v00001282d00009102sv00004554sd0000434Ebc02sc00i00" Driver Info #0: Driver Status: dmfe is active Driver Activation Cmd: "modprobe dmfe" Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #11 (PCI bridge)

    Read the article

  • Changing default gateway on workstations connected to Windows Domain SBS server

    - by Gary B2312321321
    We have xp workstations connected onto a small business server acting as active directory/isa firewall/proxy (no dhcp). Is there a reason that after installing a 2nd firewall on the network (same subnet etc), that changing the default gateway on the workstations isnt sufficient to route inet traffic through the new firewall? A freshly setup linux box connects straight on to the alternate firewall with just ip, default gateway. dns settings. Will having ISA still active on the network confuse the process? Are there further config settings deeper down in windows that need attention? Any ideas pointers on this would be appreciated? Other info: Firewalls tried: Smoothwall and Ipcop; small ethernet netwoork 40 pcs; can ping to new firwalls from workstations; activating web proxy on new firewall and reconfiguring workstation browser works fine; Point of 2nd firewall is lack of some necessary features on ISA for a linux app; Would be nice to have some redundancy to though

    Read the article

  • error while installing the libmemcached

    - by Ahmet vardar
    I get this while installing libmemcached root@server [/libmemcached]# make make all-am make[1]: Entering directory `/libmemcached' if /bin/sh ./libtool --tag=CXX --mode=compile g++ -DHAVE_CONFIG_H -I. -I. -I. -I. -I. -ggdb -DBUILDING_HASHKIT -MT libhashkit/libhashkit_libhashkit_la-aes.lo -MD -MP -MF "libhashkit/.deps/libhashkit_libhashkit_la-aes.Tpo" -c -o libhashkit/libhashkit_libhashkit_la-aes.lo `test -f 'libhashkit/aes.cc' || echo './'`libhashkit/aes.cc; \ then mv -f "libhashkit/.deps/libhashkit_libhashkit_la-aes.Tpo" "libhashkit/.deps/libhashkit_libhashkit_la-aes.Plo"; else rm -f "libhashkit/.deps/libhashkit_libhashkit_la-aes.Tpo"; exit 1; fi ./libtool: line 866: X--tag=CXX: command not found ./libtool: line 899: libtool: ignoring unknown tag : command not found ./libtool: line 866: X--mode=compile: command not found ./libtool: line 1032: *** Warning: inferring the mode of operation is deprecated.: command not found ./libtool: line 1033: *** Future versions of Libtool will require --mode=MODE be specified.: command not found ./libtool: line 1176: Xg++: command not found ./libtool: line 1176: X-DHAVE_CONFIG_H: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-ggdb: command not found ./libtool: line 1176: X-DBUILDING_HASHKIT: command not found ./libtool: line 1176: X-MT: command not found ./libtool: line 1176: Xlibhashkit/libhashkit_libhashkit_la-aes.lo: No such file or directory ./libtool: line 1176: X-MD: command not found ./libtool: line 1176: X-MP: command not found ./libtool: line 1176: X-MF: command not found ./libtool: line 1176: Xlibhashkit/.deps/libhashkit_libhashkit_la-aes.Tpo: No such file or directory ./libtool: line 1176: X-c: command not found ./libtool: line 1228: Xlibhashkit/libhashkit_libhashkit_la-aes.lo: No such file or directory ./libtool: line 1233: libtool: compile: cannot determine name of library object from `': command not found make[1]: *** [libhashkit/libhashkit_libhashkit_la-aes.lo] Error 1 make[1]: Leaving directory `/libmemcached' make: *** [all] Error 2 OUTPUT OF ./configure checking build system type... x86_64-unknown-linux-gnu checking host system type... x86_64-unknown-linux-gnu checking target system type... x86_64-unknown-linux-gnu checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for gawk... gawk checking whether make sets $(MAKE)... yes checking for style of include used by make... GNU checking for gcc... gcc checking whether the C compiler works... yes checking for C compiler default output file name... a.out checking for suffix of executables... checking whether we are cross compiling... no checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... none needed checking dependency style of gcc... gcc3 checking dependency style of gcc... (cached) gcc3 checking how to run the C preprocessor... gcc -E checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E checking for ANSI C header files... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking minix/config.h usability... no checking minix/config.h presence... no checking for minix/config.h... no checking whether it is safe to define __EXTENSIONS__... yes checking for isainfo... no checking for g++... g++ checking whether we are using the GNU C++ compiler... yes checking whether g++ accepts -g... yes checking dependency style of g++... gcc3 checking dependency style of g++... (cached) gcc3 checking whether gcc and cc understand -c and -o together... yes checking how to create a ustar tar archive... gnutar checking whether __SUNPRO_C is declared... no checking whether __ICC is declared... no checking "C Compiler version--yes"... "gcc (GCC) 4.1.2 20080704 (Red Hat 4.1.2-52)" checking "C++ Compiler version"... "g++ (GCC) 4.1.2 20080704 (Red Hat 4.1.2-52)" checking whether time.h and sys/time.h may both be included... yes checking whether struct tm is in sys/time.h or time.h... time.h checking for size_t... yes checking for special C compiler options needed for large files... no checking for _FILE_OFFSET_BITS value needed for large files... no checking for library containing clock_gettime... -lrt checking sys/socket.h usability... yes checking sys/socket.h presence... yes checking for sys/socket.h... yes checking size of off_t... 8 checking size of size_t... 8 checking size of long long... 8 checking if time_t is unsigned... no checking for setsockopt... yes checking for bind... yes checking whether the compiler provides atomic builtins... yes checking assert.h usability... yes checking assert.h presence... yes checking for assert.h... yes checking whether to enable assertions... yes checking whether it is safe to use -fdiagnostics-show-option... yes checking whether it is safe to use -floop-parallelize-all... no checking whether it is safe to use -Wextra... yes checking whether it is safe to use -Wformat... yes checking whether it is safe to use -Wconversion... no checking whether it is safe to use -Wmissing-declarations from C++... no checking whether it is safe to use -Wframe-larger-than... no checking whether it is safe to use -Wlogical-op... no checking whether it is safe to use -Wredundant-decls from C++... yes checking whether it is safe to use -Wattributes from C++... no checking whether it is safe to use -Wno-attributes... no checking for perl... perl checking for dpkg-gensymbols... no checking for lcov... no checking for genhtml... no checking for sphinx-build... no checking for working -pipe... yes checking for bison... bison checking for flex... flex checking how to print strings... printf checking for a sed that does not truncate output... /bin/sed checking for fgrep... /bin/grep -F checking for ld used by gcc... /usr/bin/ld checking if the linker (/usr/bin/ld) is GNU ld... yes checking for BSD- or MS-compatible name lister (nm)... /usr/bin/nm -B checking the name lister (/usr/bin/nm -B) interface... BSD nm checking whether ln -s works... yes checking the maximum length of command line arguments... 98304 checking whether the shell understands some XSI constructs... yes checking whether the shell understands "+="... yes checking how to convert x86_64-unknown-linux-gnu file names to x86_64-unknown-linux-gnu format... func_convert_file_noop checking how to convert x86_64-unknown-linux-gnu file names to toolchain format... func_convert_file_noop checking for /usr/bin/ld option to reload object files... -r checking for objdump... objdump checking how to recognize dependent libraries... pass_all checking for dlltool... no checking how to associate runtime and link libraries... printf %s\n checking for ar... ar checking for archiver @FILE support... @ checking for strip... strip checking for ranlib... ranlib checking command to parse /usr/bin/nm -B output from gcc object... ok checking for sysroot... no checking for mt... no checking if : is a manifest tool... no checking for dlfcn.h... yes checking for objdir... .libs checking if gcc supports -fno-rtti -fno-exceptions... no checking for gcc option to produce PIC... -fPIC -DPIC checking if gcc PIC flag -fPIC -DPIC works... yes checking if gcc static flag -static works... yes checking if gcc supports -c -o file.o... yes checking if gcc supports -c -o file.o... (cached) yes checking whether the gcc linker (/usr/bin/ld -m elf_x86_64) supports shared libraries... yes checking whether -lc should be explicitly linked in... no checking dynamic linker characteristics... GNU/Linux ld.so checking how to hardcode library paths into programs... immediate checking whether stripping libraries is possible... yes checking if libtool supports shared libraries... yes checking whether to build shared libraries... yes checking whether to build static libraries... yes checking how to run the C++ preprocessor... g++ -E checking for ld used by g++... /usr/bin/ld -m elf_x86_64 checking if the linker (/usr/bin/ld -m elf_x86_64) is GNU ld... yes checking whether the g++ linker (/usr/bin/ld -m elf_x86_64) supports shared libraries... yes checking for g++ option to produce PIC... -fPIC -DPIC checking if g++ PIC flag -fPIC -DPIC works... yes checking if g++ static flag -static works... yes checking if g++ supports -c -o file.o... yes checking if g++ supports -c -o file.o... (cached) yes checking whether the g++ linker (/usr/bin/ld -m elf_x86_64) supports shared libraries... yes checking dynamic linker characteristics... (cached) GNU/Linux ld.so checking how to hardcode library paths into programs... immediate checking whether the -Werror option is usable... yes checking for simple visibility declarations... yes checking for ISO C++ 98 include files... checking whether memcached executable path has been provided... no checking for memcached... /usr/local/bin/memcached checking whether memcached_sasl executable path has been provided... no checking for memcached_sasl... no checking whether gearmand executable path has been provided... no checking for gearmand... no checking libgearman/gearmand.h usability... no checking libgearman/gearmand.h presence... no checking for libgearman/gearmand.h... no checking for library containing getopt_long... none required checking for library containing gethostbyname... none required checking for the pthreads library -lpthreads... no checking whether pthreads work without any flags... yes checking for joinable pthread attribute... PTHREAD_CREATE_JOINABLE checking if more special flags are required for pthreads... no checking for PTHREAD_PRIO_INHERIT... yes checking the location of cstdint... configure: WARNING: Could not find a cstdint header. <stdint.h> checking the location of cinttypes... configure: WARNING: Could not find a cinttypes header. <inttypes.h> checking whether byte ordering is bigendian... no checking for htonll... no checking for working SO_SNDTIMEO... yes checking for working SO_RCVTIMEO... yes checking for supported struct padding... yes checking for alarm... yes checking for dup2... yes checking for getline... yes checking for gettimeofday... yes checking for memchr... yes checking for memmove... yes checking for memset... yes checking for pipe2... no checking for select... yes checking for setenv... yes checking for socket... yes checking for sqrt... yes checking for strcasecmp... yes checking for strchr... yes checking for strdup... yes checking for strerror... yes checking for strtol... yes checking for strtoul... yes checking for strtoull... yes checking arpa/inet.h usability... yes checking arpa/inet.h presence... yes checking for arpa/inet.h... yes checking fcntl.h usability... yes checking fcntl.h presence... yes checking for fcntl.h... yes checking libintl.h usability... yes checking libintl.h presence... yes checking for libintl.h... yes checking limits.h usability... yes checking limits.h presence... yes checking for limits.h... yes checking malloc.h usability... yes checking malloc.h presence... yes checking for malloc.h... yes checking netdb.h usability... yes checking netdb.h presence... yes checking for netdb.h... yes checking netinet/in.h usability... yes checking netinet/in.h presence... yes checking for netinet/in.h... yes checking stddef.h usability... yes checking stddef.h presence... yes checking for stddef.h... yes checking sys/time.h usability... yes checking sys/time.h presence... yes checking for sys/time.h... yes checking execinfo.h usability... yes checking execinfo.h presence... yes checking for execinfo.h... yes checking cxxabi.h usability... yes checking cxxabi.h presence... yes checking for cxxabi.h... yes checking sys/sysctl.h usability... yes checking sys/sysctl.h presence... yes checking for sys/sysctl.h... yes checking umem.h usability... no checking umem.h presence... no checking for umem.h... no checking for C++ compiler vendor... gnu checking for working alloca.h... yes checking for alloca... yes checking for error_at_line... yes checking for pid_t... yes checking vfork.h usability... no checking vfork.h presence... no checking for vfork.h... no checking for fork... yes checking for vfork... yes checking for working fork... yes checking for working vfork... (cached) yes checking for stdlib.h... (cached) yes checking for GNU libc compatible malloc... yes checking for stdlib.h... (cached) yes checking for GNU libc compatible realloc... yes checking whether strerror_r is declared... yes checking for strerror_r... yes checking whether strerror_r returns char *... yes checking for stdbool.h that conforms to C99... yes checking for _Bool... no checking for int16_t... yes checking for int32_t... yes checking for int64_t... yes checking for int8_t... yes checking for off_t... yes checking for pid_t... (cached) yes checking for ssize_t... yes checking for uint16_t... yes checking for uint32_t... yes checking for uint64_t... yes checking for uint8_t... yes checking whether byte ordering is bigendian... (cached) no checking for an ANSI C-conforming const... yes checking for inline... inline checking for working volatile... yes checking for C/C++ restrict keyword... __restrict checking whether the compiler supports GCC C++ ABI name demangling... yes checking sasl/sasl.h usability... no checking sasl/sasl.h presence... no checking for sasl/sasl.h... no checking uuid/uuid.h usability... yes checking uuid/uuid.h presence... yes checking for uuid/uuid.h... yes checking for main in -luuid... yes checking for clock_gettime in -lrt... yes checking for floor in -lm... yes checking for sigignore... yes checking atomic.h usability... no checking atomic.h presence... no checking for atomic.h... no checking for setppriv... no checking for winsock2.h... no checking for poll.h... yes checking for sys/wait.h... yes checking for fnmatch.h... yes checking for MSG_NOSIGNAL... yes checking for MSG_DONTWAIT... yes checking for MSG_MORE... yes checking event.h usability... yes checking event.h presence... yes checking for event.h... yes checking for main in -levent... yes checking for endianness... little configure: creating ./config.status config.status: creating Makefile config.status: creating docs/conf.py config.status: creating libhashkit-1.0/configure.h config.status: creating libmemcached-1.0/configure.h config.status: creating libmemcached-1.2/configure.h config.status: creating libmemcached-2.0/configure.h config.status: creating support/libmemcached.pc config.status: creating support/libmemcached.spec config.status: creating support/libmemcached-fc.spec config.status: creating libtest/version.h config.status: creating config.h config.status: config.h is unchanged config.status: executing depfiles commands config.status: executing libtool commands --- Configuration summary for libmemcached version 1.0.6 * Installation prefix: /usr/local * System type: unknown-linux-gnu * Host CPU: x86_64 * C Compiler: gcc (GCC) 4.1.2 20080704 (Red Hat 4.1.2-52) * Assertions enabled: yes * Debug enabled: no * Warnings as failure: no * SASL support: --- anyone knows how to solve this ?

    Read the article

  • Using the Juniper EX3300 Switch as a router?

    - by Richard Whitman
    I have a Juniper EX3300 switch in a data center. And I have connected one of the uplink ports (ge-0/1/0) to my ISP's router. I want to configure it so that all the devices connected to ports in the same VLAN as ge-0/1/0 can access the Internet. I have done some research, and I haven't gotten anywhere really. I have configured the interface as follows: ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family inet { address xx.xx.xx.xx/32; } } } where xx.xx.xx.xx is the "Customer Router Port IP" assigned by my ISP. When I try to commit, I get the following error: Interface ge-0/1/0.0 not enabled for switching Can some one tell me what is the right way to configure it?

    Read the article

  • Integrating NetBeans for Raspberry Pi Java Development

    - by speakjava
    Raspberry Pi IDE Java Development The Raspberry Pi is an incredible device for building embedded Java applications but, despite being able to run an IDE on the Pi it really pushes things to the limit.  It's much better to use a PC or laptop to develop the code and then deploy and test on the Pi.  What I thought I'd do in this blog entry was to run through the steps necessary to set up NetBeans on a PC for Java code development, with automatic deployment to the Raspberry Pi as part of the build process. I will assume that your starting point is a Raspberry Pi with an SD card that has one of the latest Raspbian images on it.  This is good because this now includes the JDK 7 as part of the distro, so no need to download and install a separate JDK.  I will also assume that you have installed the JDK and NetBeans on your PC.  These can be downloaded here. There are numerous approaches you can take to this including mounting the file system from the Raspberry Pi remotely on your development machine.  I tried this and I found that NetBeans got rather upset if the file system disappeared either through network interruption or the Raspberry Pi being turned off.  The following method uses copying over SSH, which will fail more gracefully if the Pi is not responding. Step 1: Enable SSH on the Raspberry Pi To run the Java applications you create you will need to start Java on the Raspberry Pi with the appropriate class name, classpath and parameters.  For non-JavaFX applications you can either do this from the Raspberry Pi desktop or, if you do not have a monitor connected through a remote command line.  To execute the remote command line you need to enable SSH (a secure shell login over the network) and connect using an application like PuTTY. You can enable SSH when you first boot the Raspberry Pi, as the raspi-config program runs automatically.  You can also run it at any time afterwards by running the command: sudo raspi-config This will bring up a menu of options.  Select '8 Advanced Options' and on the next screen select 'A$ SSH'.  Select 'Enable' and the task is complete. Step 2: Configure Raspberry Pi Networking By default, the Raspbian distribution configures the ethernet connection to use DHCP rather than a static IP address.  You can continue to use DHCP if you want, but to avoid having to potentially change settings whenever you reboot the Pi using a static IP address is simpler. To configure this on the Pi you need to edit the /etc/network/interfaces file.  You will need to do this as root using the sudo command, so something like sudo vi /etc/network/interfaces.  In this file you will see this line: iface eth0 inet dhcp This needs to be changed to the following: iface eth0 inet static     address 10.0.0.2     gateway 10.0.0.254     netmask 255.255.255.0 You will need to change the values in red to an appropriate IP address and to match the address of your gateway. Step 3: Create a Public-Private Key Pair On Your Development Machine How you do this will depend on which Operating system you are using: Mac OSX or Linux Run the command: ssh-keygen -t rsa Press ENTER/RETURN to accept the default destination for saving the key.  We do not need a passphrase so simply press ENTER/RETURN for an empty one and once more to confirm. The key will be created in the file .ssh/id_rsa.pub in your home directory.  Display the contents of this file using the cat command: cat ~/.ssh/id_rsa.pub Open a window, SSH to the Raspberry Pi and login.  Change directory to .ssh and edit the authorized_keys file (don't worry if the file does not exist).  Copy and paste the contents of the id_rsa.pub file to the authorized_keys file and save it. Windows Since Windows is not a UNIX derivative operating system it does not include the necessary key generating software by default.  To generate the key I used puttygen.exe which is available from the same site that provides the PuTTY application, here. Download this and run it on your Windows machine.  Follow the instructions to generate a key.  I remove the key comment, but you can leave that if you want. Click "Save private key", confirm that you don't want to use a passphrase and select a filename and location for the key. Copy the public key from the part of the window marked, "Public key for pasting into OpenSSH authorized_keys file".  Use PuTTY to connect to the Raspberry Pi and login.  Change directory to .ssh and edit the authorized_keys file (don't worry if this does not exist).  Paste the key information at the end of this file and save it. Logout and then start PuTTY again.  This time we need to create a saved session using the private key.  Type in the IP address of the Raspberry Pi in the "Hostname (or IP address)" field and expand "SSH" under the "Connection" category.  Select "Auth" (see the screen shot below). Click the "Browse" button under "Private key file for authentication" and select the file you saved from puttygen. Go back to the "Session" category and enter a short name in the saved sessions field, as shown below.  Click "Save" to save the session. Step 4: Test The Configuration You should now have the ability to use scp (Mac/Linux) or pscp.exe (Windows) to copy files from your development machine to the Raspberry Pi without needing to authenticate by typing in a password (so we can automate the process in NetBeans).  It's a good idea to test this using something like: scp /tmp/foo [email protected]:/tmp on Linux or Mac or pscp.exe foo pi@raspi:/tmp on Windows (Note that we use the saved configuration name instead of the IP address or hostname so the public key is picked up). pscp.exe is another tool available from the creators of PuTTY. Step 5: Configure the NetBeans Build Script Start NetBeans and create a new project (or open an existing one that you want to deploy automatically to the Raspberry Pi). Select the Files tab in the explorer window and expand your project.  You will see a build.xml file.  Double click this to edit it. This file will mostly be comments.  At the end (but within the </project> tag) add the XML for <target name="-post-jar">, shown below Here's the code again in case you want to use cut-and-paste: <target name="-post-jar">   <echo level="info" message="Copying dist directory to remote Pi"/>   <exec executable="scp" dir="${basedir}">     <arg line="-r"/>     <arg value="dist"/>     <arg value="[email protected]:NetBeans/CopyTest"/>   </exec>  </target> For Windows it will be slightly different: <target name="-post-jar">   <echo level="info" message="Copying dist directory to remote Pi"/>   <exec executable="C:\pi\putty\pscp.exe" dir="${basedir}">     <arg line="-r"/>     <arg value="dist"/>     <arg value="pi@raspi:NetBeans/CopyTest"/>   </exec> </target> You will also need to ensure that pscp.exe is in your PATH (or specify a fully qualified pathname). From now on when you clean and build the project the dist directory will automatically be copied to the Raspberry Pi ready for testing.

    Read the article

  • Static IPv6 address advertising and IPv6 autoconfig in Debian/Ubuntu

    - by Pascal
    I have a network that advertises IPv6 addresses through IPv6 autoconfig. To allow DNS lookups and to have fancy IP addresses, we setup "static" IPv6 addresses through /etc/network/interfaces: auto eth0 iface eth0 inet dhcp iface eth0 inet6 static address a:b:c:d:e::f netmask 64 Whenever we now connect through IPv6 Linux uses the IPv6 autoconfig address: a:b:c:d:21d:60ff:fe4a:479 and not the static IPv6 address: a:b:c:d:e::f A server on the other side only sees the autoconfig address. Is there a way to force linux (Debian/Ubuntu) to use the static address for outgoing packets? This is especially interesting for reverse DNS and firewall settings. I don't want to disable the IPv6 autoconfig since I don't have control over the settings the router advertises.

    Read the article

  • CentOS - massive usage on loopback interface

    - by Matthew Iselin
    Hi, I have a CentOS installation which is running fairly smoothly. Today I ran ifconfig mainly to see what sort of usage has been coming across the ethernet interface, and to also check my link speed. This is what I ended up seeing for the loopback device: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:10301085132061223274 errors:0 dropped:0 overruns:0 frame:0 TX packets:13981054163812689233 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11783901785008000095 (0.6 EiB) TX bytes:10333501021200548281 (0.9 EiB) This just feels completely wrong - almost an EiB of data? Any assistance in tracking down the source of these statistics would be greatly appreciated.

    Read the article

  • Wireless networking on Gnome on Ubuntu 9 / 10

    - by WaveyDavey
    So here's my problem: I have some netbooks (ASUS eee, and ACER Aspire Ones) that I've been tasked to set up as kiosk machines, locked up tight for normal users. I am a command-line, server man, so this gnome malarkey is all a bit new to me. I found a lovely 9.04 kiosk livecd that installs and runs exactly as I want it to, but I can't get the wireless working. So I dropped on a full 10.4 distro, and wireless works straight out of the box (so hardware is good) - all I needed to do was right-click on the network connection icon, enter my SSID and password (WPA/WPA2) and away it went, perfect. Further investigation on 10.4 distro shows that /etc/networking/interfaces is virtually empty (just auto lo iface lo inet loopback in it), even after I have set up the wireless thru the gnome taskbar applet (is that the right word?). So where does gnome / ubuntu store the network settings to bring the blasted wireless connection up, and what do I need to do on the kiosk version to get wireless running?

    Read the article

  • Basic networking problem with Ubuntu 9.04 on Acer Extensa 5635Z laptop

    - by sapporo
    I just installed Ubuntu 9.04 on a brand new Acer Extensa 5635Z laptop, but ethernet networking does't work (wireless doesn't work either, but I'd be happy with ethernet for now). eth0 isn't listed in /etc/network/interfaces: $ cat /etc/network/interfaces auto lo iface lo inet loopback lshw does show the nic, but I can't make much sense out of the information: $ sudo lshw -class network -sanitize *-network DISABLED description: Wireless interface product: AR928X Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:07:00.0 logical name: wmaster0 version: 01 serial: [REMOVED] width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath9k latency=0 module=ath9k multicast=yes wireless=IEEE 802.11bgn *-network UNCLAIMED description: Ethernet controller product: Attansic Technology Corp. vendor: Attansic Technology Corp. physical id: 0 bus info: pci@0000:09:00.0 version: c0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list configuration: latency=0 *-network DISABLED description: Ethernet interface physical id: 1 logical name: pan0 serial: [REMOVED] capabilities: ethernet physical configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes Thanks for your help!

    Read the article

  • Postfix "warning: cannot get RSA private key from file"

    - by phew
    I just followed this tutorial to set up a postfix mailserver with dovecot and mysql as backend for virtual users. Now I got the most parts working, I can connect to pop3 pop3s imap and imaps. Using echo TEST-MAIL | mail [email protected] works fine, when I log into my hotmail account it shows the email. It also works in reverse hence my MX entry for mydomain.com finally has been propagated, so I am being able to receive emails sent from [email protected] to [email protected] and view them in Thunderbird using STARTTLS via IMAP. Doing a bit more research after I got the error message "5.7.1 : Relay access denied" when trying to send mails to [email protected] using Thunderbird being logged into [email protected], I figured out that my server was acting as an "Open Mail Relay", which - ofcourse - is a bad thing. Digging more into the optional parts of the tutorial like shown workaround.org/comment/2536 and workaround.org/ispmail/squeeze/postfix-smtp-auth I decided to complete these steps aswell to be able to send mails via [email protected] through Mozilla Thunderbird, not getting the error message "5.7.1 : Relay access denied" anymore (as common mailservers reject open relayed emails). But now I ran into an error trying to get postfix working with SMTPS, in /var/log/mail.log it reads Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: cannot get RSA private key from file /etc/ssl/certs/postfix.pem: disabling TLS support Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: TLS library problem: 20251:error:0906D06C:PEM routines:PEM_read_bio:no start line:pem_lib.c:650:Expecting: ANY PRIVATE KEY: Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: TLS library problem: 20251:error:140B0009:SSL routines:SSL_CTX_use_PrivateKey_file:PEM lib:ssl_rsa.c:669: That error is logged right after I try to send a mail from my newly installed mailserver using SMTP SSL/TLS via port 465 in Thunderbird. Thunderbird then tells me a timeout occured. Google has a few results concerning that problem, yet I couldn't get it working with any of those. I would link some of them here but as a new user I am only allowed to use two hyperlinks. My /etc/postfix/master.cf looks like smtp inet n - - - - smtpd smtps inet n - - - - smtpd -o smtpd_tls_wrappermode=yes -o smtpd_sasl_auth_enable=yes and nmap tells me PORT STATE SERVICE [...] 465/tcp open smtps [...] my /etc/postfix/main.cf looks like smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no append_dot_mydomain = no readme_directory = no #smtpd_tls_cert_file = /etc/ssl/certs/postfix.pem #default postfix generated #smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key #default postfix generated smtpd_tls_cert_file = /etc/ssl/certs/postfix.pem smptd_tls_key_file = /etc/ssl/private/postfix.pem smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smptd_sasl_auth_enable = yes smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination myhostname = mydomain.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost.com, localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all virtual_mailbox_domains = mysql:/etc/postfix/mysql-virtual-mailbox-domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql-virtual-mailbox-maps.cf virtual_alias_maps = mysql:/etc/postfix/mysql-virtual-alias-maps.cf virtual_transport = dovecot dovecot_destination_recipient_limit = 1 mailbox_command = /usr/lib/dovecot/deliver The *.pem files were created like described in the tutorial above, using Postfix To create a certificate to be used by Postfix use: openssl req -new -x509 -days 3650 -nodes -out /etc/ssl/certs/postfix.pem -keyout /etc/ssl/private/postfix.pem Do not forget to set the permissions on the private key so that no unauthorized people can read it: chmod o= /etc/ssl/private/postfix.pem You will have to tell Postfix where to find your certificate and private key because by default it will look for a dummy certificate file called "ssl-cert-snakeoil": postconf -e smtpd_tls_cert_file=/etc/ssl/certs/postfix.pem postconf -e smtpd_tls_key_file=/etc/ssl/private/postfix.pem I think I don't have to include /etc/dovecot/dovecot.conf here, as login via imaps and pop3s works fine according to the logs. Only problem is making postfix properly use the self-generated, self-signed certificates. Any help appreciated! EDIT: I just tried this different tutorial on generating a self-signed certificate for postfix, still getting the same error. I really don't know what else to test. I also did check for the SSL libraries, but all seems to be fine: root@domain:~# ldd /usr/sbin/postfix linux-vdso.so.1 => (0x00007fff91b25000) libpostfix-global.so.1 => /usr/lib/libpostfix-global.so.1 (0x00007f6f8313d000) libpostfix-util.so.1 => /usr/lib/libpostfix-util.so.1 (0x00007f6f82f07000) libssl.so.0.9.8 => /usr/lib/libssl.so.0.9.8 (0x00007f6f82cb1000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007f6f82910000) libsasl2.so.2 => /usr/lib/libsasl2.so.2 (0x00007f6f826f7000) libdb-4.8.so => /usr/lib/libdb-4.8.so (0x00007f6f8237c000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007f6f82164000) libresolv.so.2 => /lib/libresolv.so.2 (0x00007f6f81f4e000) libc.so.6 => /lib/libc.so.6 (0x00007f6f81beb000) libdl.so.2 => /lib/libdl.so.2 (0x00007f6f819e7000) libz.so.1 => /usr/lib/libz.so.1 (0x00007f6f817d0000) libpthread.so.0 => /lib/libpthread.so.0 (0x00007f6f815b3000) /lib64/ld-linux-x86-64.so.2 (0x00007f6f83581000) After following Ansgar Wiechers instructions its finally working. postconf -n contained the lines as it should. The certificate/key check via openssl did show that both files are valid. So it indeed has been a permissions problem! Didn't know that chown'ing the /etc/ssl/*/postfix.pem files to postfix:postfix is not enough for postfix to read the files.

    Read the article

  • IP alias lost when changing main IP

    - by rmflow
    my /etc/network/interfaces: auto eth0 iface eth0 inet static address 192.168.3.75 netmask 255.255.255.0 gateway 192.168.3.0 Situation 1: After linux booted I set an IP alias: ifconfig eth0:0 192.168.3.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.3.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 is lost! Situation 2: After linux booted I set an IP alias: ifconfig eth0:0 192.168.4.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.4.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 stays! How do I properly change main IP, so all my aliases are not lost?

    Read the article

  • Cannot run SSH or send commands to /etc/init.d/ssh

    - by ThinkBohemian
    When I attempt to execute any commands such as /etc/init.d/ssh restart or /etc/init.d/ssh start, I get no output. It just goes to the next command line (Ubuntu Hardy). I can even pass in junk parameters such as /etc/init.d/ssh asldkfjalskfdj and i get no warnings or error messages, it just goes to the next line. I can check in my processes: lsof -i :22 and don't see my ssh process. I also don't see my SSH process when i run: netstat -na --inet Any troubleshooting suggestions?

    Read the article

  • Remote Access Problems with DRAC 5 on Dell PowerEdge 1950

    - by Darin Peterson
    Today I received my first Dell PowerEdge 1950 server with a DRAC 5 card. On my local network I have static configurations on my Linux systems using this for instance: iface eth0 inet static address 192.168.1.210 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 8.8.8.8 8.8.4.4 For the DRAC card, I configured the LAN like this: address 192.168.1.215 netmask 255.255.255.0 gateway 192.168.1.1 For the advanced LAN settings I used dns-nameservers 8.8.8.8 8.8.4.4 I've tried many different IP addresses, but cannot communicate with the card. Is there anyone who might know if I have configuration issues, or maybe if the card might be bad?

    Read the article

  • afp/smb transfers caps at 2 megabytes/sec, wireless N

    - by CQM
    I wanted to transfer files between two mac computers. The network is wireless-N and both computers have wireless-N modules in them. The problem is that when I transfer files between them, via file sharing (afp) the network speed caps at 2 megabytes/sec. Just downloading files from the internet I can get faster speeds, so this isn't a constriction of my wifi bandwidth, it appears to be a constriction of the protocol being used. My wifi-n is set to 130mbits, so I should see real world transfer speeds around 12-16 megabytes/sec I did this command on both computers sudo sysctl -w net.inet.tcp.delayed_ack=0 which is supposed to lower tcp overhead, but this did not affect it. How can I get the speed I am expecting?

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >