Search Results

Search found 4091 results on 164 pages for 'intel celeron'.

Page 20/164 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

• Screen flickering when using midrange brightness values on Dell XPS

  - by Eliran Malka

  After a fresh Ubuntu install on my laptop, I discovered the function keys for screen brightness control (Fn+F4 and Fn+F5) are not working. Digging around here, I managed to get it to work by following the solution suggested on this post and that one, but alas — after applying it, a strange problem occurred: Setting the brightness level to any value other than minimum or maximum, the screen starts flickering back and forth from the selected level to full brightness, apparently due to Dell's power saver attempting to dim the screen to adjust the brightness levels. I looked up for a solution here on the site, and possibly everywhere, with no avail. Also tried: To manually control the brightness by configuring the ACPI level (setting values by echo [some_value] | sudo tee /sys/class/backlight/[vendor]_backlight/[some_key], without success. Installing the Intel graphics driver, thinking it's missing. Realized it's installed out of the box by installing Mesa Utils. How to resolve this? Environment Model: Dell Studio XPS 13 OS: Windows 7 64bit / Ubuntu 12.04 32bit (dual boot) Graphics Driver: Intel HD 3000 (Sandybridge Mobile x86/MMX/SSE2) lshw -C display output: *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:47 memory:f0000000-f03fffff memory:e0000000-efffffff ioport:2000(size=64)

  Read the article

• How to get Unity working on dual gpu laptop?

  - by Mourgos

  I recently bought a new laptop (Asus X53S series) that has two GPUs, an NVidia GeForce GT 540M and an integrated Intel GPU (I believe it's called Intel HD graphics 3000). I installed the recommended restricted NVidia drivers after a clean Ubuntu 11.10 install. In the 'additional drivers' program I get the message: "This driver is enabled and in use", although when I try to open the NVidia X Server Settings it says "You do not appear to be using the NVIDIA X driver." which seems to be the case since Ubuntu only starts using Unity 2D. I've had the same issue in 11.04 and I was forced to use the nouveau driver just to get unity working, but since I get quite a few crashes with it I really want to get the propriety driver working this time around. Since I've never had this issue with older laptops, I can only assume it is caused due to the dual gpu configuration. How do I get Ubuntu to use the propriety drivers, or is there any workaround to get the integrated Intel GPU to be ignored by Ubuntu? Alternatively, has anyone got Unity working with a similar setup?

  Read the article

• WIFI/LAN not working after Installing Ubuntu 13.10

  - by user183025

  I can't connect to my WIFI after installing Ubuntu 13.10. I tried re-installing it three times (thinking that I did something wrong during the installation) but I still can't connect to my WIFI. It just gives me the message that I'm offline and that I can't connect to my WIFI. I also tried connecting to the internet using LAN cable but with the same results. I tried google but it seems that there's no solution to this yet.... Anybody knows how to solve this? Thanks! FYI: H/W path Device Class Description ====================================================== system RC530/RC730 (To be filled by O.E.M.) /0 bus RC530/RC730 /0/0 memory 64KiB BIOS /0/4 processor Intel(R) Core(TM) i5-2410M CPU @ 2.30GHz /0/4/5 memory 32KiB L1 cache /0/41 memory 4GiB System Memory /0/41/0 memory DIMM [empty] /0/41/1 memory 4GiB SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) /0/100 bridge 2nd Generation Core Processor Family DRAM Controller 02:00.0 Network controller: Intel Corporation Centrino Wireless-N 130 (rev 34) Subsystem: Intel Corporation Centrino Wireless-N 130 BGN Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at f7200000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06) Subsystem: Samsung Electronics Co Ltd Device c0c1 Flags: bus master, fast devsel, latency 0, IRQ 41 I/O ports at b000 [size=256] Memory at f2104000 (64-bit, prefetchable) [size=4K] Memory at f2100000 (64-bit, prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169

  Read the article

• What are the specific uses of these hardware? [closed]

  - by vincentbelkin

  So I'm trying to learn more about databases and information systems. However I need more explanation on the specific purpose of these hardware. I'm not sure if they are servers or what. HP AlphaServer ES47 Tower Tru64 Unix Intel-Based B, Proliant ML350GA Two Intel-Based A Proliant ML570T03 Intel-Based X236 Intel Quad Core Xeon Category B X3500 Poweredge 1400 SC Btw I'm just a college student who wants to know more about these hardware

  Read the article

• Intel Wireless 4965AGN not achieving N throughput when connected to an Airport Express N network

  - by BenA

  I have an Intel Wireless WiFi Link 4965AGN adaptor in my laptop (HP Pavillion dv2000 series) which is connecting to a 5Ghz-only 802.11n network provided by an Apple Airport Express. The network is using WPA2 encryption. My desktop is also connected the Airport, via a Linksys WUSB600N USB adaptor. Both are running with the latest drivers, and the Airport is running the latest firmware. The Airport is also configured to use wide channels. The problem I have is that I never get throughput above 4MB/s when transferring files between the two machines. Even a pessimistic calculation shows a 270Mbps network as being capable of transfer rates at well above 10MB/s. I'm pretty sure I've isolated the issue to being the Intel adaptor, as wiring the desktop to the AP, and using the Linksys adaptor on the laptop immediately yielded speeds limited by the 100MB/s ethernet connection. I know that 802.11n is still a draft standard, and so mixing kit from different manufacturers can easily lead to poor results, but I was just wondering if anybody else out there has had success with this Intel adaptor on an N network? Or even better, connecting it to an Airport Express? Can anybody give me any advice on how to troubleshoot this issue? I should also mention that the Airport Express doesn't allow you to manually specify channels when running in N mode, and that I've been able to rule out interference from other Wireless LANs by scanning. There aren't any other 5GHz networks in my area. All ideas welcome! Update: A while later, I've just updated to the most recent drivers for both the Intel chip in the laptop, and the USB adaptor. Unfortunately this hasn't improved things :(. If anybody has any advice it would be be gratefully received.

  Read the article

• Should I enable "Intel NIC DMA Channels"?

  - by javapowered

  I have HP DL360p Gen8 646902-xx1 I'm trying to optimize my config for low latency trading. Should I enable "Intel NIC DMA Channels"? Will that help/affect my system? From HP doc: Added a new ROM Based Setup Utility (RBSU) Advanced Performance Option menu that allows the user to enable Intel NIC DMA Channels (IOAT). This option is disabled by default. When enabled, certain networking devices may see an improvement in performance by utilizing Intel's DMA engine to offload network activity. Please consult documentation from the network adapter to determine if this feature is supported.

  Read the article

• SSD for Visual studio : Intel X25-m G2 or OCZ Vertex

  - by meska

  hi, looking for laptop upgrade, and thinking about SSD drive. Laptop would be Dell Studio XPS with T9400 as i can get one for a very good price. So i was thinking about replacing the built in 500 GB hdd with some kind of SDD Currently two choices: OCZ Vertex Series 60 GB vs. Intel X25-M G2 MLC 80 GB Price is almost the same. From anandtech Intel performs badly in sequential write, but scores very high numbers in random write and random read (good for visual studio?) and i get more space. What do you think? OCZ Vertex or Intel X25-M G2 ? Purely from Visual Studio 2008 and upcoming 2010 perspective?

  Read the article

• Installing Intel Rapid Storage Drivers makes my eSATA Drives act weird

  - by Filip Ekberg

  I have a HP 8530w Elitebook this Laptop got an eSATA port which I want to plug my LaCie d2 Quadra V2 1TB harddrive into. It all works well on a fresh install of Windows 7 without the Intel Chipset drivers installed. However when I install the Intel Rapid Storage drivers or the Intel Matrix software my drive seems to "disconnect" when I use it to much. I have a lot of Virtual PC's on the drive and when I start them the disk somewhat disconnects. What could cause this?

  Read the article

• Intel Xeon vt-d query

  - by deploymonkey

  Does Xeon westmere ep (xeon 56xx series) have vt-d (=iommy / direct io) or does intel TXT (Intel® Trusted Execution Technology) include vt-d? I'm at a loss. I've been researching current processors for an important project for some time now. I need to know, if the xeon 5600s (Westmere EP) include vt-d (iommu/directed io/pci passing) because the system will run virtualized guests. This enables direct hardware access eg. pci passthrough, in xen for example. It seems that the 5600s TXT should incorporate vt-d and that xeon 5600s should include vt-d as they are ramped up 5500s, but there is no conclusive answer anywhere. Intel's processor comparison only states that 5500s have vt-d and no TXT and 5600s have no vt-d but TXT. I'd be really grateful if anybody could clear this up and possibly even provide a citation. Thanks a lot.

  Read the article

• Problem with intel chipset 4 serie and centos dealing with dual head

  - by Antoine

  I've a fujitsu lifebook S7220, it's been a while since i try to configure it to use a dual head with centos 5.4 x86_64. Everytime I try, the xserver crash... I've got an intel chipset mobile 4 serie (GMA 4500MHD, if I recall good!) When I do an lspci -v i've got these : 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller]) Subsystem: Fujitsu Limited. Unknown device 1451 Flags: bus master, fast devsel, latency 0, IRQ 177 Memory at f2000000 (64-bit, non-prefetchable) [size=4M] Memory at d0000000 (64-bit, prefetchable) [size=256M] I/O ports at 1800 [size=8] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 3 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) Subsystem: Fujitsu Limited. Unknown device 1451 Flags: bus master, fast devsel, latency 0 Memory at f2400000 (64-bit, non-prefetchable) [size=1M] Capabilities: [d0] Power Management version 3 My question is, anyone already got this problem and how did you fix it? Thank you for your answer!

  Read the article

• Mobile Intel 965 vs 4 Series chipset speed differences

  - by graham.reeds

  A client of ours is having a problem panning on a mapping application that we write on their panasonic toughbooks (CF-19's). One of their toughbooks the panning is fairly smooth while on the other it is really slow. Doesn't help that they have all the settings turned up, but I would of thought any reasonably new graphics card (even shared memory) would have more than adequate graphic speed. I am pretty sure that the graphic adapter is to blame, but I can't find anything out about either chipset (level of acceleration, non-problems, etc). All I get is the intel data sheets. The faster panning one is on the Mobile Intel 4 Series Express Chipset while the slower is on the Mobile Intel 965 Express Chipset. Is this expected? Does it sound like a driver problem? They both have the same amount of ram and same cpu.

  Read the article

• Unable to enable wireless on a Vostro 2520

  - by Joe

  I have a Vostro 2520 and not sure how to enable wireless on my machine. The details are given below, would appreciate any pointers to resolving this issue. lsmod returns Module Size Used by ath9k 132390 0 ath9k_common 14053 1 ath9k ath9k_hw 411151 2 ath9k,ath9k_common ath 24067 3 ath9k,ath9k_common,ath9k_hw b43 365785 0 mac80211 506816 2 ath9k,b43 cfg80211 205544 4 ath9k,ath,b43,mac80211 bcma 26696 1 b43 ssb 52752 1 b43 ndiswrapper 282628 0 ums_realtek 18248 0 usb_storage 49198 1 ums_realtek uas 18180 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_cirrus 24002 1 joydev 17693 0 parport_pc 32866 0 ppdev 17113 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep psmouse 97362 0 dell_wmi 12681 0 sparse_keymap 13890 1 dell_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq wmi 19256 1 dell_wmi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device mac_hid 13253 0 i915 473240 3 drm_kms_helper 46978 1 i915 uvcvideo 72627 0 drm 242038 4 i915,drm_kms_helper videodev 98259 1 uvcvideo soundcore 15091 1 snd dell_laptop 18119 0 dcdbas 14490 1 dell_laptop i2c_algo_bit 13423 1 i915 v4l2_compat_ioctl32 17128 1 videodev snd_page_alloc 18529 2 snd_hda_intel,snd_pcm video 19596 1 i915 serio_raw 13211 0 mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 sudo lshw -class network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7c00000-f7c07fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 07 serial: 78:45:c4:a3:aa:65 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.1.5 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:e000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: yes Output of lspci > 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev > 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge > Graphics Controller (rev 09) 00:16.0 Communication controller: Intel > Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB > controller: Intel Corporation Panther Point USB Enhanced Host > Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther > Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: > Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) > 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root > Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point > PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel > Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) > 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller > (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 > port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel > Corporation Panther Point SMBus Controller (rev 04) 07:00.0 Network > controller: Broadcom Corporation Device 4365 (rev 01) 09:00.0 Ethernet > controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express > Gigabit Ethernet controller (rev 07) Output of lspci -v 0:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) (prog-if 00 [VGA controller]) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at f7800000 (64-bit, non-prefetchable) [size=4M] Memory at e0000000 (64-bit, prefetchable) [size=256M] I/O ports at f000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 42 Memory at f7d0a000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at f7d08000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at f7d00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 Memory behind bridge: f7c00000-f7cfffff Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=09, subordinate=09, sec-latency=0 I/O behind bridge: 0000e000-0000efff Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at f7d07000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0 Capabilities: <access denied> Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Device 0558 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 40 I/O ports at f0b0 [size=8] I/O ports at f0a0 [size=4] I/O ports at f090 [size=8] I/O ports at f080 [size=4] I/O ports at f060 [size=32] Memory at f7d06000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) Subsystem: Dell Device 0558 Flags: medium devsel, IRQ 11 Memory at f7d05000 (64-bit, non-prefetchable) [size=256] I/O ports at f040 [size=32] Kernel modules: i2c-i801 07:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) Subsystem: Dell Device 0016 Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at f7c00000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 41 I/O ports at e000 [size=256] Memory at f0004000 (64-bit, prefetchable) [size=4K] Memory at f0000000 (64-bit, prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169

  Read the article

• C#: how to obtain the current clock speed of an Intel i-series CPU when TurboBoost is activated

  - by shifuimam

  I know that it's possible to get this information - Intel's own TurboBoost sidebar gadget appears to use an ActiveX control to determine the current clock speed of an i3/i5/i7 CPU when TurboBoost is active. However, I'm wanting to do this programmatically in C# - obtaining the CurrentClockSpeed value from WMI tops out at the set maximum clock speed of the CPU, so in TurboBoost mode, it doesn't report the current actual clock speed.

  Read the article

• how to return NULL for double function with Intel C compiler?

  - by Derek

  I have some code that I am porting from an SGI system using the MIPS compiler. It has functions that are declared to have double return type. If the function can't find the right double, those functions return "NULL" The intel C compiler does not like this, but I was trying to see if there is a compiler option to enable this "feature" so that I can compile without changing code. I checked the man page, and can't seem to find it. Thanks

  Read the article

• How can I make sound over hdmi in kubuntu work?

  - by user32509

  I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :)

  Read the article

• info about intel Cos embedded i86 os

  - by Tim Williscroft

  I've got some old Intel printer (Etherexpress XL ) print servers and they seem to be running an Intel OS called Cos aka Intel Client Os i86 I've found out that much just looking in the update files from Intel. It was at least partly written in C. How do I make a custom software image Intel Cos's boot loader will understand ? I know a host PC xmodem's the image to the client device, and I was wondering if anyone had already either reverse-engineered this or had original info ? or is my only recousre to reverse engineer the update file format ?

  Read the article

• The Direction Of Intel Graphics With Fedora 13 Alpha

  <b>Phoronix:</b> "...each Fedora release always pulls in the very latest Linux graphics code. Fedora was the first distribution shipping with the Nouveau driver, then its KMS driver, and now with Fedora 13 it's the first OS deploying Nouveau's Gallium3D driver..."

  Read the article

• Ubuntu on the Sony Vaio VPCY 21S1E

  - by tiax

  My girlfriend got a new Subnotebook for Christmas (Sony Vayo VPCY21S1E), which comes with an "Intel HD graphics" vga adaptor. When I try to boot the Ubuntu installer from USB, the screen goes blank after a short while, before I even see the Ubuntu logo. However, when I select "nomodeset" in the boot options, I can boot it to the CLI login prompt. When I start X, though, that only works in VESA mode (I've read Intel eventually got rid of Usermode Mode Setting and only offers KMS now, which I've disabled to get it to boot). What can I do to enable a) higher resolution than 1024x768 in VESA b) hardware acceleration for compiz, video playback, etc?

  Read the article

• Triple-head on a Lenovo T520

  - by codeape

  Lenovo T520 with integrated Intel HD graphics + a NVidia card (Optimus) Ubuntu 11.10 on the computer. I would like to use the built-in screen plus two external screens. This PDF indicates that it is possible to connect up to four external monitors to the laptop. The information is Windows only. I was planning to disable the NVidia card, since I have read that Linux support for Optimus is not good. Questions: Has anyone set up three monitors on NVidia hardware? Has anyone set up three monitors using Intel HD 3000? Can I expect it to work out of the box, or are there tricks I need to be aware of?

  Read the article

• how do i fix this: the networking and wireless are enabled. but list of networks under wireless networks not available

  - by Ayesha Ahmad

  i started working with ubuntu 11.10 last year. i upgraded to 12.04 a week back. since then i have had all sorts of problems with network connection. first had to install the new driver. the hardware switch somehow got disabled then the above problem arrived. even tho the options are all enabled, the OS is not able to detect scan available network connections. also i have to bring to notice that once in a while it does get connected, can not explain how it happens. I want to fix this problem once and for all. please help. ifconfig: eth0 Link encap:Ethernet HWaddr f0:4d:a2:51:b3:c8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:44 eth1 Link encap:Ethernet HWaddr 1c:65:9d:67:d5:e1 inet6 addr: fe80::1e65:9dff:fe67:d5e1/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:170 TX packets:0 errors:27 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:344 errors:0 dropped:0 overruns:0 frame:0 TX packets:344 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:20336 (20.3 KB) TX bytes:20336 (20.3 KB) lshw -c network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 1c:65:9d:67:d5:e1 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: f0:4d:a2:51:b3:c8 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) iwconfig lo no wireless extensions. eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:196 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) I hope this information is of some help.

  Read the article

• Intel, Nokia Partner on Top-End Smartphone OS

  The smartphone alliance between the two tech giants reflects the need to circle the wagons in the face of increased competition.

  Read the article

• Intel Gears Up for the Small Business Server Market

  The computer chip maker plans to build a small business server platform based on a processor typically found in a netbook.

  Read the article

• Installing Ubuntu 12.04 on NUC intel i3 DC3217IYE

  - by Kieron

  System: NUC i3, 2 hdmi ports, ethernet, no wireless. UEFI boot 2x2gb ram 30gb mSATA internal drive Ubuntu 64bit 12.04.03 Hello i am having much trouble loading an OS on my NUC. I started out attempting another OS with various loaders (beast/hack) without much success,(various panics on boot or endless reboot loops, or graphics failures) after many tries i decided to attempt Ubuntu. Many years ago i loaded Ubuntu on an e-machine without an issue so i figured it would go smoothly, nothing could be further from the truth. The Live USB stick loads, but when i am installing the OS it always fails to load grub 2. Obviously it wont boot from SSD without grub2. I searched and found that Boot-repair should fix it...so i created a live usb with boot repair...it refuses to repair the grub because the install never finished and the needed partions are not fully created and flagged. It also demands an internet connection which i am unable to provide. I then ran gparted in an attempt to create the needed partitions manually, then re-ran boot repair turning off the "check internet" option. and disabling the re-install grub hoping it would create the missing directories and or fix the flags. it appeared to run successfully but upon return to the Ubuntu live USB it still fails at the grub2 install. also gparted doesnt have the same choices that Ubuntu install has when creating partitions, causing it to not recognize that i already had a root, or an EFI directory or it sometimes couldnt tell what the format of the partition was...all very annoying the reason i cant connect to internet (and cant upload the error logs) is the nuc only has Ethernet and the location i have to set up is too far away from modem. i can not move the monitor closer to modem as it is a 50inch LCD. I just want to do a basic install with one user acct and remote desktop (vnc) turned on so i can move the NUC to the modem connect via ethernet and then finish setting it up via Remote desktop/VNC chicken from my mac. While i await any assistance you maybe able to provide i am going to attempt to switch to the 32bit version and legacy boot to see if that can load grub. thnx again to anyone that can come up with a possible solution. i would love to hit "erase and install ubuntu" if anyone can figure out what is stopping that simple answer from working. Also disks (CD/DVD) are not an option as neither my Mac mini or my NUC have optical drives, and i have no desire to buy one for one task

  Read the article

• Assembleur Intel avec NASM en mode protégé, par Etienne Sauvage

  Bonjour, Vous trouverez à cette adresse : http://esauvage.developpez.com/tutor...tel-avec-nasm/ un parcours du combattant, un cheminement de quelqu'un qui, partant d'à peu près rien, essaye d'arriver à pas beaucoup plus mais quand même. Ce n'est pas vraiment un tutoriel parce que ça n'a pas d'objectif précis, ce n'est pas un cours car c'est riche en approximations. C'est plutôt le suivi d'un trappeur face à l'immensité canadienne. Néanmoins, comme j'ai remarqué que visiblement et contre toute attente, ça intéresse des gens, je crée cette discussion afin de recueillir les retours éventuels. Cordialement, Le chevalie...

  Read the article

• How is the RIP loaded when an interrupt arrives in an IA-32e 64-bit IDT Gate Descriptor?

  - by Vern

  I need some help with the programming of an IA-32e Interrupt Descriptor as I'm pretty new to it. I don't think I quite understand how the RIP is loaded when an Interrupt arrives. There is a Segment Selector in Intel's 64-bit IDT Gate Descriptor. However, from my understanding across the 5 part Intel manuals, the Linear Address of the Interrupt Handler is loaded into RIP from the 64-bit offset specified in the IDT Gate Descriptor. The only use of the segment selector is to check: if there is a change in privilege levels the Interrupt Handler is truly pointing to a code segment My questions are: Is RIP taken from the 64-bit offset only? Or is RIP = offset(sign extended to 64-bits) + segment selector base? Is the base address pointed to by the segment selector in the IDT Gate Descriptor ignored? Or does it have a use?

  Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >