Search Results

Search found 1051 results on 43 pages for 'nic foster'.

Page 20/43 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

  • kvm -net only passing broadcast, multicast, and guest destination traffic

    - by user52874
    Figured this out just last week, but I can't find it now. Even printed it out. Can't find that either. Frustrating...so...help! Configured a 'monitoring' nic on a kvm guest (running 'Security Onion, if it matters). I read (somewhere) that the default nic configuration for a kvm guest is to only pass broadcast traffic, multicast traffic, and traffic with the guest's mac as a destination. There is an option to override this behaviour, and pass all traffic. It's something like --mac-filtering=no, or --mac-restriction=no, or something like that. Worked beautifully. Does this look at all familiar to anyone who can clue me in to the exact option syntax? thx.

    Read the article

  • Remote Desktop fails after VPN connection.

    - by Samet Sorgut
    The remote computer is connected with Remote Desktop. When the remote computer is connected to VPN the Remote Destop freezes. It is not possible to connect to the remote computer again via Remote Desktop. What can be done to connect to this remote computer after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest?

    Read the article

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • Updated: NLB 2 Windows Server 2003 Servers - Looking to Hire SysAdmin to solve!

    - by Paul Hinett
    I need to configure windows NLB on 2 dedicated servers I have. My main machine has been running for some time, with several domain names pointing to the servers primary IP address. Both servers have 2 NIC's installed, and both have several secondary public IP addresses available if needed? What IP address would I use for the cluster IP, does this IP need to be added to the IP list of both public NIC's ip address list? What IP addresses do I use for the host's dedicated IP? Please help, this is driving me nuts...i've taken down the server twice on accident today! UPDATE: Looking to hire a windows SysAdmin to solve! I have updated my question, i would like to hire a trusted windows SysAdmin to take care of this for me, preferably today...can anyone help and provide some credentials please? Thank you in advance!

    Read the article

  • Trixbox CentOS Default GW Problem (Multi-homed server)

    - by slashp
    I'm having an issue with a CentOS trixbox server which is dual-homed (one private facing NIC [eth1], one internet-facing NIC [eth0]). I can't seem to get the default gateway to set properly to our ISP's GW via eth0. I've modified the /etc/sysconfig/network to contain both a GATEWAY & GATEWAYDEV line and removed the GATEWAY line from /etc/sysconfig/network-scripts/ifcfg-eth1 (as well as /etc/sysconfig/network-scripts/ifcfg-eth0). No default GW shows up in the routing table unless it's specified in the ifcfg-eth1 file (which both the wrong interface and wrong gateway IP), otherwise, the routing table simply does not contain a default gateway..any ideas would be greatly appreciated! Thanks! EDIT Just realized when attempting to add the default gateway manually using the route add command, I receive an error stating: SIOCADDRT: Network is unreachable I know this error can occur when your default gateway and interface IP address are not on the same subnet..in this case, my public IP address of eth0 is a /29.

    Read the article

  • Transient network dropout for Xen DomU's

    - by Stephen C
    We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

    Read the article

  • What is the maximum number of TCP connections I can have in Windows Server 2008?

    - by evilfred
    I would like to have as many connections (single connections from many different clients) as humanly possible in a server running on Windows Server 2008, in order to support a Comet-style application. The application is written in C#. The connections will not be chatty, they just need to be open (and stay open). Buying boatloads of memory and fast CPUs are not a problem. As far as I can tell, I will be limited to 65k simultaneous open connections per NIC - the maximum number of ports. Is this accurate? Or can I go beyond 65k connections / NIC somehow? It seems like there are server products for Linux at least that support hundreds of thousands of connections. How do they do this?

    Read the article

  • Does Cisco anyconnect replace original network connection session?

    - by Stan
    When using Cisco anyconnect VPN, it seems the existing network connection is still going through old connection session (Is there any way to find out)? The reason is because when using Cisco VPN client connect to gateway, usually the Messenger Live, Skype will be disconnected and requires to reconnect. But using anyconnect doesn't need to reconnect. So I am guessing if those old sessions still go through original network connection. Which means, both connection is existing at the same time. Take my case for example: connection 1: wireless NIC - cable modem - my cable ISP - internet connection 2: anyconnect - wireless NIC - cable modem - my cable ISP - VPN gateway - internet Am I correct? Is there any way to check this? Thanks.

    Read the article

  • No DNS resolving with VPN (RRAS)

    - by Sven
    I have a RRAS server setup on a Windows 2003 machine with two NIC's. The VPN works like a charm, I can ping all the other computers on the network. But it fails when I try to access resources with hostnames. I searches for a solution but the ones I found are about RRAS setup with a remote DHCP server. But in my case it's the RRAS server that hands out the ip addresses (option for redirection for WINS, DNS is ON and set to the LAN NIC). I also heard something about FQDN.. but I don't really understand what that is.

    Read the article

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • How do I run a batch file async using PSExec?

    - by Paul Mrozowski
    I have a batch file I run that, among other things, reset's the NICs in the machine. I have some watchdog software running on another machine that monitors the first one. I'd like to run this batch file using PSExec when it detects certain types of failures. The problem I'm having is that since the batch file reset's the NIC's it kills the connection PSExec has (I'm OK with that). The real issue is that when PSExec dies the batch file stops running (leaving the NIC's disabled). I've tried using the -i option with PSExec with no luck. Any ideas about basically just fire off the batch file and NOT have it stop when PSExec is disconnected?

    Read the article

  • Jumbo Frames on DIR-655

    - by Spookyone
    Hello, I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU Synology DS107+, Firmware 3.0-1337 Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

    Read the article

  • How do I network this Windows Failover Cluster and MongoDB Replica Set? (diagram inside)

    - by arex1337
    As you can see, my two Windows Server Failover Cluster (WSFC) nodes have three network interfaces each, which connects them to three different networks : A public network A private network consisting of the WSFC nodes A private network consisting of the WSFC nodes and a machine with the WSFC Quorum Witness File Share Does this network configuration I've planned, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. My two MongoDB Replica Set nodes also have three network interfaces each - very similar to the previous situation: A public network A private network consisting of the primary and secondary MongoDB Replica Set nodes A private network consisting of the primary, secondary and arbiter MongoDB Replica Set nodes Does this network configuration, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. Here is the simpler version I'm considering: UPDATE:

    Read the article

  • Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

    - by Sise
    Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

    Read the article

  • Jumbo Frames, ISCSI and ESXi

    - by vlannoob
    I have enabled Jumbo Frames (9000) in ESXi for all my vmNICs, vmKernels, vSwitches, iSCSI Bindings etc - basically anywhere in ESXi where it has an MTU settings I have put 9000 in it. The ports on the switches (Dell PowerConnects) are all set for Jumbo Frames. I have a Dell MD3200i with 2 controllers, each with 4 ports for iSCSI. Each of these ports is set to Jumbo Frames (9000) as well. So now the questions: Do I need to log into each Windows Server VM I am running and delve into the NIC properties and manually set it to Jumbo Frames in the NIC properties in the device Manager as well? Whats the best way of testing that Jumbo Frames are indeed working as intended?

    Read the article

  • Unidentified network: How to configure TCP/IPv4 for Win7?

    - by Zolomon
    When I try to connect to internet I keep getting the error "Unidentified network". I've tried numerous attempts at restoring access without success. IP release, flushing DNS cache, reinstalling NIC, reactivating NIC, resetting router and so on... I've read several times that it's my default gateway that's wrong. Currently I've had automatic IP/DNS configuration set without any problems, and then it stopped working for some reason. Anyone know how I specify the IP? My subnetmask is 255.255.255.0, default gateway is 192.168.0.1 but I have no idea how to determine what IP I should set. I use a D-Link DIR-655 and other computers on the network have IPs like 192.168.0.194, next is 192.168.0.197. (I'm completely lost and am trying to cool down after two weekends of debugging filled with despair.)

    Read the article

  • Jumbo Frames on DIR-655

    - by Spookyone
    I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU Synology DS107+, Firmware 3.0-1337 Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

    Read the article

  • DNS record reappears after having been deleted

    - by palmbardier
    I've got a Microsoft Windows Server 2003 R2 acting as a domain controller for a small network. It provides DHCP and DNS among a few other services. It's only got a single NIC, but it's configured with two IP addresses. I want it's name to resolve to one of the two IP addresses assigned to its NIC. I've unchecked "Register this connection's addresses in DNS" under the "Advanced TCP/IP Settings". Currently we've got two distinct DNS Host (A) records for this domain controller: dc-001 - 10.0.0.1 dc-001 - 10.0.100.1 I've deleted the first entry but it continues to reappear in my dnsmgmt snap-in. Unfortunately I'm not a Microsoft systems administrator by trade. Does anyone familiar with Microsoft server environments know why a deleted Host (A) record would reappear? Is there another check-box I need to toggle? Thanks in advance to all of you Microsoft experts out there.

    Read the article

  • Windows Server 2003 Router, Good approach [closed]

    - by jM2.me
    Possible Duplicate: Windows Server 2003 Router with PortForwarding Situation We have Verizon Fios 25/25 Internet Connection, Server acting as a router, and around 12 office computers. Task Portforward port 29000 from office computer. Problem Once I connected wan and lan cables I just had to set static lan ip (on server) and plug in switch with office computers into second nic. Then just right click on wan nic and select share internet connection. All office computers were assigned with an IP address 192.168.0.XXX and Gateway 192.168.0.1 (server). Now I have to open port and portfoward it from computer 192.168.0.190 (static ip, manual). Using this guide http://www.rosscode.com/blog/index.php?title=port_forwarding_in_windows_2003&more=1&c=1&tb=1&pb=1 I faced a problem. Before enabling "RRA" I had to unshare internet connection (wan interface) and was able to setup network. Now how do I setup a network within "RRA" and share internet with private network? Thank you much

    Read the article

  • Windows Server 2003: Nat Port Forwarding Not Working

    - by jM2.me
    The setup is following: Internet (108.99.XXX.XX) <- Windows Server 2003 (10.0.0.1) <- Switch <- Office Computers (10.0.0.100-200 some static routes some manual some automatic) Windows Server has NAT installed on it and two network interfaces are configured properly. The problem is, whenever I try to forward port 80 (or any other) from office computer (lets say 10.0.0.100), it fails. Nic #1 Settings: All settings are obtained from ISP Nic #2 Settings: Set manually IP: 10.0.0.1 Mask: 255.255.255.0 Nat Server is configured to automatically assign IP addresses to private network. Settings are: IP: 10.0.0.0 Mask: 255.255.255.0 Forwarding was done in Routing and Remote Access (local) - IP Routing - NAT/Basic Firewall - Local Area Connection (right click_properties) - services and ports - Web Server HTTP - Private Address: 10.0.0.100 SO what is causing the problem of failure to forward any port from other computer inside private network?

    Read the article

  • Is A Managed Switch With VLAN Support Required

    - by Justin
    Hello, I am wondering if I need to buy a switch which is managed (VLAN support) for my configuration, or will a cheaper unmanaged switch work? I have servers with two NICS each. The first NIC is public and the second NIC is private. The router will plug into the switch port 1 let's say (public). Then server 1 public plugs into port 2 on the switch, and sever 1 private plugs into port 3 on the switch. The public interface is: 192.168.X.X / 255.255.0.0 and the private interface is 10.0.X.X / 255.255.0.0. So looks like: ** SWITCH ** Port Device Network 1 Router/Firewall 192.168.X.X 2 Server 1 Public 192.168.X.X 3 Server 1 Private 10.0.X.X 4 Server 2 Public 192.168.X.X 5 Server 2 Private 10.0.X.X 6 Server 3 Public 192.168.X.X 7 Server 3 Private 10.0.X.X Thanks.

    Read the article

  • KVM guest storage difference with NBD and NFS

    - by WojonsTech
    I am setting up my own little private cloud for my own use maybe for a project or to. I am using linux kvm on debian 6. I have 3 servers 2 of them for compute nodes and 1 storage node. I would I have already installed kvm made a few test machines got my networking setup. I have 2 nics on each server 1 nic is for web traffic other nic is for network traffic. My first Idea was to use NFS for storing the guest machines which can range in size, maybe 8gb maybe 100gb, it just depends. I was doing have heard of nbd before seems like it could work but I dont know what the performance differences are and if it will effect my enviroment, nfs looks like it will be easier to use.

    Read the article

  • Upgraded from 11.10 to 12.04 now no network access

    - by MadeTheLeap
    A few weeks ago I decided I should enter the Linux world and read that Ubuntu is the most widely used release. I installed version 11.10 and it worked perfectly. Just this past week I decided I would do the upgrade to 12.04. The upgrade process itself worked fine. However, when I logged in I no longer had a network connection. I am running an AMD-based PC with a D-LINK DFE-530TXS network card and as I said, it worked fine in 11.10. I have scoured the Internet and come across a thousand slightly varying solutions, but they are too convoluted for someone new to Linux. Not because I can't follow the steps, but because most of the tools/utilities that are referenced (e.g. to compile, install, etc.) are not available when I use the stated steps in the solutions. So....should I re-install 11.10 or is there hope in getting this version to use the NIC that I know works. I have the latest driver from d-link for my NIC but I have no idea how to 'install' it for Ubuntu 12.04 to use. I know you will require additional information, but I wasn't sure what you would need. Thanks in advance.

    Read the article

  • VLAN help on ESX 4/vSphere

    - by user49032
    I setup a new VLAN with ID 153 in vSphere for my ESX4 server. The VLAN is setup for virtual machines and then I added a new NIC to the VM I want to be able to access the VM. The NIC is added to VLAN 153, but yet I am unable to ping the VLAN .1 IP that is setup on our Cisco 3750. The IP is properly setup on the Cisco 3750 because I'm able to ping the interface IP from other machines on the network. I'm guessing there must be an issue with the cabling. Any ideas?

    Read the article

  • Do MORE with WebCenter

    - by Michael Snow
    WEBCAST THURSDAY!! 03/22/12 Do you need to lower costs? Raise Productivity? Foster Innovation? Improve Online Engagement? But you’re still stuck with Documentum? Step away from the ledge – there is hope – let us help you. Top 4 Content Imperatives · Lower Costs - Reduce labor, maintenance fees, storage and electrical consumption · Raise Productivity - Automation and integration, communication, findability · Foster Innovation - Enable collaboration, expertise location · Improve Online Engagement – enable user-driven, dynamic marketing initiatives With the coming technology wave we see four content imperatives. Every organization has had to reduce costs, cost cutting has become a way of life. Everyone is working three jobs as positions are eliminated. And so we have to reduce labor, reduce maintenance, and reduce money we are wasting on things like storing content that is redundant or no longer useful. We also, to fill that gap, need to raise productivity. Knowledge workers represent the fastest growing segment of the workforce, accounting for 40%-75% of the employees at organizations in sectors like financial services, life sciences, healthcare and retail.  What’s more, their wages total 18 percent of the United States GDP. And so we can’t afford information systems that don’t let our top performers be the best they can be. We look to automate the content processes, provide ways to integrate that content into our processes, provide communication to make decisions, and to make content more findable so people can make the right decision and move the process forward. And really to get ourselves out of the current financial status, we can only cut costs so far. We have to innovate out of economic tough times – to find new products and new markets. And to enable the innovation process, we have to enable collaboration and expertise location. So much of innovation is about building on innovations that have come before. To solve problems, we have to be able to find what our organization has already created. We find that problems we need to solve have already been solved if we can find the right document, the right person. So we have to provide systems that enable us to stand on the shoulders of our organization’s accomplishments. Good content drives great marketing. Online engagement is growing as an absolute necessity for modern growing marketing organizations that require the business users be enabled for dynamic marketing content creation, updates and targeted content creation and management. Unfortunately – if you are currently stuck with Documentum, you are really lacking in your Web Experience Management capabilities. Documentum previously used FatWire for web publishing. Now FatWire is part of Oracle. Oracle provides powerful web engagement capabilities: Increase sales and loyalty by optimizing online engagement Create, manage and moderate contextually relevant, targeted and interactive online experiences Optimize customer engagement across, web, mobile and social channels Manage large scale multichannel global online presence with integration to enterprise applications Enable business users to control their content and make their own updates Publish content from native files – enable navigation of project documents, procedures, policy information Enable content display and updates from existing web applications – one click to drag and drop content management functionality So you get the ability to self-publish information and make it navigable, to move the process of publishing from IT to business users, and the ability to address a whole new area of user engagement with web experience management. So… if you are still stuck with Documentum and don’t know what to do – contact us – not only will Oracle help you step away from the ledge, but also with the MoveOff Documentum program, we are offering you a way – trade-in your Documentum licenses for a 100% credit on Oracle WebCenter. How’s that for a nice bonus? It’s time to stop maintaining Documentum, and to start innovating with Oracle WebCenter. Learn More Here! To learn more about what Oracle WebCenter can offer you today – join us for a webcast – your eyes will be opened to all that’s possible. Do More with WebCenter: Extend Beyond Content Management

    Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >