Search Results

Search found 5933 results on 238 pages for 'mass storage'.

Page 202/238 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >

• Wireless router setup for 1-1 NAT

  - by Carlos

  What I have: A linksys router WAG160N with firmware version 2 A "pool" of 5 external static IP's provided by my ISP 213.xx.xxx.n All the required configuration values for the static IPs such as (Subnet Mask, Gateway and static DNS 1, 2, 3) Current WAN Configuration: Encapsulation: RFC 2364 PPPoA Multiplexing: VC QoS type: UBR DSL modulation: MultiMode What's connected to the network: 1 x Server (That I want to make available to the outside) 5 x Desktops with static internal IP's, such as 192.168.0.xx 2 x Network printers, also with internal static IP's 2 x Laptops 1 x NAS (Network Attached Storage) also on static IP What I want to do: I would like to make the server available from outside the network, for example from your house. The problem is that Im not really sure how to do this. I have tried following the steps on the instruction manual in Linksys but they do not seem to work, once I set it up as shown bellow, I loose internet and all hell breaks loose. Going into further detail, I would prefer if the network is changed as little as possible, by this I mean that all the computers stay networked within eachother and only the server is accessible from the outside the network. What I need HELP with: I have read around that it is possible to set a 1-1 NAT (I know where it is in the menu but have no clue what it does...) so that I can NAT a single public IP directly to a single private IP (in our case the server). But please, How do I do that? Or maybe an alternative?

  Read the article

• Forcing programs to be installed to another drive

  - by zyboxenterprises

  I have an SSD as my main Windows drive, with a 640GB 2.5" HDD, partitioned to store programs and user settings, and also to act as backup (it's the only thing I had lying around at the time of building my PC). The task was to make the PC as fast as possible, while having an increased storage capacity available to store normal user data, and to assist in my small data recovery business. The problem is that whenever I install a program, it installs to C:\Program Files [(x86 for the 32 bit programs]\, although I have changed the environment variables. This wouldn't normally be an issue, however every installation program points its shortcut to my 640GB HDD. The root layout of both drives: To clarify: Program files get installed to C:\ Program shortcuts are always pointed to Z:\, my 640GB HDD Modifying the relevant environment variables doesn't do anything, I looked at this, but however it only talks about modifying the registry and environment variables, which I have already done so. I install to the Z:\ drive if the installation program lets me change the installation path, but however the installation programs sometimes don't let me change this. Is there a way that I can force every program to install to the relevant location on Z:\? Perhaps I'm missing something here? Edit: Found this program; would it be appropriate to use in my case? I would be able to move the entire Program Files (and its x86 version) to Z:\, without impacting on the performance.

  Read the article

• Getting access to physical drives in ESXi v5.5 installation on Dell PowerEdge R710 with PERC 6/i

  - by Big-Blue

  I've acquired a Dell PowerEdge R710 server a few days ago, which includes a PERC 6/i RAID controller. The server is now fitted with a SATA SSD, one SAS drive and four SATA HDD's, all of which I would like to be passed through to ESXi in an "as-is" state, without creating any logical drives in the RAID controller. Now, the ESXi v5.5 installation image I grabbed from the Dell homepage starts just fine but only lists the logical drives and connected flash drives as possible installation targets, not any of the physical drives. If I create a small logical drive on my SSD (which the PERC 6/i detects as SATA-SSD type), the ESXi install wizard lists the SSD value on that drive as false; which is far from optimal. I have also tried disabling the RAID controller entirely in the setup, but that also did not help. Everything that should enable passthrough is enabled in BIOS, but that shouldn't be a concern at this early stage of the ESXi installation. How would I be able to install ESXi v5.5 to a part of my SSD that is connected to the storage controller, while giving it entire physical access to the disk (to allow for SMART values to be read etc.)?

  Read the article

• netlogon errors

  - by rorr

  I have two instances of mssql 2005 and am using CA XOSoft replication. The master is a failover cluster and the replica is a standalone server. They are all running Server 2003 sp2 x64. Same patch levels on all servers. This setup has worked great for several months until we recently restricted the RPC ports on both nodes of the master(5000 - 6000 using rpccfg.exe). We have to implement egress filtering, thus the limiting of the ports. We began receiving login errors for sql windows authentication and NETLOGON Event ID: 5719: This computer was not able to set up a secure session with a domain controller in domain due to the following: Not enough storage is available to process this command. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. We also see group policies failing to update and cluster file shares go offline at the same time. The RPC ports were set back to default when we started seeing these problems and the servers rebooted, but the problems persist. The domain controllers are not showing any errors. Running dcdiag and netdiag shows everything is fine. We have noticed that the XOSoft service ws_rep.exe is using a lot of handles(8 - 9k), about the same number that sqlserver is using. As soon as xosoft replication is stopped the login errors cease and everything functions correctly. I have opened a ticket with CA for XOSoft, but I'm not sure that the problem is actually xosoft, but that it is the one bringing the problem to light. I'm looking for tips on debugging RPC problems. Specifically on limiting the ports and then reverting the changes.

  Read the article

• How to Set up MySQL Server to utilize more memory

  - by Cyril Gupta

  Hi there, I have MySQL setup on Windows along with Plesk. The version is 5.0.45 Community. The databases I have on the server are MyISAM as well as InnoDb, but predominantly innodb. I had 8G memory on my server, but MySQL isn't going up more than 1.3G and tweaking the settings isn't helping. I tried to increase the memory allocation for innodb_buffer_pool_size, it works if I set it up to 1G, but if I set 2G, or above the server doesn't come back online! I want mySQL to use at least 5-6 Gigs of the memory I have for performance, but I can't get this to work. Can anyone please help? My mysql config file is below (there are 2 mysqld sections... when i used MySQL workbench it created another one!) [MySQLD] port=3306 basedir=C:\\Program Files (x86)\\Parallels\\Plesk\\Databases\\MySQL datadir=C:\\Program Files (x86)\\Parallels\\Plesk\\Databases\\MySQL\\Data default-character-set=latin1 default-storage-engine=INNODB query_cache_size=128M table_cache=1024 tmp_table_size=32M thread_cache=32 myisam_max_sort_file_size=100G myisam_max_extra_sort_file_size=100G myisam_sort_buffer_size=2M key_buffer_size=32M read_buffer_size=16M read_rnd_buffer_size=2M sort_buffer_size=8M innodb_additional_mem_pool_size=24M innodb_flush_log_at_trx_commit=1 innodb_log_buffer_size=10M innodb_buffer_pool_size=1G innodb_log_file_size=10M innodb_thread_concurrency=8 max_connections=700 key_buffer=48M max_allowed_packet=5M sort_buffer=2M net_buffer_length=4K old_passwords=1 wait_timeout=20 connect_timeout=60 [client] port=3306 [mysqld] query_cache_min_res_unit = 4096 innodb_additional_mem_pool_size = 1048576 innodb_buffer_pool_size = 1G query_cache_limit = 1048576 key_buffer_size = 8388608 sort_buffer_size = 2097144 query_cache_type = 1 query_cache_size = 312M log-slow-queries connect_timeout = 5 wait_timeout = 20 thread_cache_size = 15 read_buffer_size = 131072 table_cache = 64

  Read the article

• Index a low-cost NAS on Windows 7

  - by JcMaco

  Has anyone found a way to index the files stored on a Networked Attached Storage on Windows 7 so that the files can be available in Windows Search and Libraries? I am referring to the cheap and available NAS like the Western Digital My Book series that use an embedded linux server. Similar question: http://windows7forums.com/windows-7-networking/6700-indexing-nas-drive-libraries.html EDIT Windows help proposes to make the files stored on the NAS available offline. This is obviously not a good solution if the NAS has more data than what the client can store. If the folder is on a network device that is not part of your homegroup, it can be included as long as the content of the folder is indexed. If the folder is already indexed on the device where it is stored, you should be able to include it directly in the library. If the network folder is not indexed, an easy way to index it is to make the folder available offline. This will create offline versions of the files in the folder, and add these files to the index on your computer. Once you make a folder available offline, you can include it in a library. When you make a network folder available offline, copies of all the files in that folder will be stored on your computer's hard disk. Take this into consideration if the network folder contains a large number of files.

  Read the article

• Installing Linux on a Windows 8.1 laptop

  - by nicoX

  I would like to clean install a linux distribution as Ubuntu etc. My laptop that runs Windows 8.1. I have two options in mind. Clean install or dual boot. My technical question is: my laptop have a 8GB SSD drive, which it uses to boot Windows with and a 500GB for storage. I wonder what that 8GB SSD stores? It can't store the whole Windows install as that would be much more than 8GB. Also if I would do a clean install of Ubuntu could I use the 8GB SSD to have Ubuntu boot up quicker. How would I install it. Option two, if I would like to dual boot, how would I proceed having the SSD to boot both systems? I also wish to ask about the Legacy and UEFI differences. Windows runs with UEFI. So when I'm installing Linux, should I run Legacy, and if I dual boot, what option to I choose?

  Read the article

• Performance data collection for short-running, ephemeral servers

  - by ErikA

  We're building a medical image processing software stack, currently hosted on various AWS resources. As part of this application, we have a handful of long-running servers (database, load balancers, web application, etc.). Collecting performance data on those servers is quite simple - my go-to- recipe of Nagios (for monitoring/notifications) and Munin (for collection of performance data and displaying trends) will work just fine. However - as part of this application, we are constantly starting up and terminating compute instances on EC2. In typical usage, these compute instances start up, configure themselves, receive a job from a message queue, and then get to work processing that job, which takes anywhere from 15 minutes to over 8 hours. After job completion, these instances get terminated, never to be heard from again. What is a decent strategy for collecting performance data on these short-lived instances? I don't necessarily need monitoring on them - if they fail for whatever reason, our application will detect this and handle re-starting the job on another instance or raising the flag so an administrator can take a look at things. However, it still would be useful to collect information like CPU (user, idle, iowait, etc.), memory usage, network traffic, disk read/write data, etc. In our internal database, we track the instance ID of the machine that runs each job, and it would be quite helpful to be able to look up performance data for a specific instance ID for troubleshooting and profiling. Munin doesn't seem like a great candidate, as it requires maintaining a list of munin nodes in a text file - far from ideal for an environment with a high amount of churn, and for the short amount of time each node will be running, I'd rather keep the full-resolution data indefinitely than have RRD water down the data over time. In the end, my guess is that this will require a monitoring engine that: uses a database (MySQL, SQLite, etc.) for configuration and data storage exposes an API for adding/removing hosts and services Are there other things I should be thinking about when evaluating options? Perhaps I'm over-thinking this, though, and just ought to run sar at 1-minute intervals on these short-lived instances and collect the sar db files prior to termination.

  Read the article

• Upgraded users to Win7. Now getting "path not found" when saving files or opening attachments

  - by Matt Penner

  We have a Server 2008 AD environment with about 5k users. We just rolled out Windows 7 SP1 (were XP) with great success. However, about once a day we get a few calls that a user opens a file from their Documents (the folder is on the server and redirected), edits it and attempts to save but Win7 reports that the path is not found either because it doesn't exist or no permissions. The only way to fix it is to delete the profile. In addition we get about the same number but different users saying that they cannot open attachments from Outlook 2010 due to no permission. We have to edit the temp Outlook storage path in the registry to fix it (or delete the profile). I think the two issues may be related. What scares us is that we rolled out 1 month ago and had no calls of this nature until about 2 weeks ago. It started off as one or two but seems to be growing. Any ideas? We're going to open a Microsoft ticket but I wanted to seenif anyone else has run into this. Thanks!

  Read the article

• VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

  - by Dayton Brown

  I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

  Read the article

• "iostat" command different in two equal machines

  - by Oz.

  We have several machines on Amazon (ec2) of the type c1.xlarge with 8 cpus, running the Amazon AMI. Details on the machine: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge One out of the several machines is showing a high load average, since we have run the last yum upgrade a couple of weeks a go. We did not yet update the other machines, and everything looks normal on them. The strange thing is that the top command not showing any hint for the cause of the load. CPUs are - 4.8%us, 1.1%sy, 0.0%ni, 94.1%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st. Mem is about 1.5GB free. Any idea what could it be, or where else can we check? iostat command on the proper machine: avg-cpu: %user %nice %system %iowait %steal %idle 8.97 0.03 4.46 0.19 0.14 86.23 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.60 0.69 55.38 587620 47254184 xvdfp2 2.64 1.10 61.04 934786 52091056 xvdfp4 0.86 0.19 41.72 163866 35601920 xvdfp1 4.37 36.59 73.89 31220810 63051504 xvdfp3 8.03 7.08 94.63 6045402 80749184 iostat command on problematic machine: avg-cpu: %user %nice %system %iowait %steal %idle 9.29 0.04 5.55 0.26 0.11 84.74 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.13 3.34 68.85 246244 5077888 xvdfp1 7.60 74.31 104.88 5480362 7734840 xvdfp3 13.22 73.67 125.00 5433386 9218600 xvdfp4 1.11 0.76 65.08 55762 4799248 xvdfp2 4.16 3.31 99.17 243818 7313264 Many thanks for the help.

  Read the article

• Issue with InnoDB engine while enabling and [ skip-innodb ]

  - by Ahn

  How to enable InnoDB, which was previously disabled with skip-innodb option. Case 1: Disabled the innodb with skip-innodb option and show engines givens as below. Engine | Support ... | InnoDB | NO ...... Case 2: As I want to enable the innodb, I commanded the #skip-innodb option and restarted. But now the show engines even not showing the InnoDB engine in the list. ? Mysql Version : 5.1.57-community-log OS : CentOS release 5.7 (Final) Log: 120622 13:06:36 InnoDB: Initializing buffer pool, size = 8.0M 120622 13:06:36 InnoDB: Completed initialization of buffer pool InnoDB: No valid checkpoint found. InnoDB: If this error appears when you are creating an InnoDB database, InnoDB: the problem may be that during an earlier attempt you managed InnoDB: to create the InnoDB data files, but log file creation failed. InnoDB: If that is the case, please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/error-creating-innodb.html 120622 13:06:36 [ERROR] Plugin 'InnoDB' init function returned error. 120622 13:06:36 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 120622 13:06:36 [Note] Event Scheduler: Loaded 0 events 120622 13:06:36 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.57-community-log' socket: '/data/mysqlsnd/mysql.sock1' port: 3307 MySQL Community Server (GPL)

  Read the article

• Replace Linux Boot-Drive | ext3 to btrfs

  - by bardiir

  I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

  Read the article

• What's throttling the database?

  - by Troels Arvin

  Hardware: Intel x86_64 with 192GB of RAM. OS: CentOS 5.4 x86_64. DBMS: DB2 v. 9.7.1 64 bit. During certain special workloads (e.g. parallel REORGs/RUNSTATs), I've seen the server transporting 450MB/s with 25000IO/s (yes, there is probably some storage system caching happening here) while all CPU cores were happily working in an even mix of usermode/wait. And disk benchmark tools can also bring some very satisfying bandwith and IO/s numbers to the table. On the other hand, we also have another scenario: A single rather complex query with at least one large table scan. db2's "list applications" reports that the query is Executing (not locked). IO: At most 10MB/s, 500 IO/s; CPU: two cores in 99.9% wait state, all other cores 100% idle. The tables which the query reads from have been altered to have LOCKSIZE=TABLE, so I would think that lock list work is zero. What's going on in such a situation? What tools/snapshots/... can I use to gain better insight in such a case?

  Read the article

• Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

  Read the article

• UW-IMAP server, high load for one user

  - by Bruce Garlock

  We have been experiencing a very strange anomaly, with one specific user with our UW-IMAP server. We have about 75 users using the server, and one particular user, who is in about the middle as far as used storage keeps having issues with slow speed. Most of our users all use Thunderbird 2, or Thunderbird 3. Mostly 2, because of the performance issues we have had with 3. This user was on 3, and I downgraded him to 2. The performance has gotten better, but according to the imapd processes on the server, his username is using the most CPU % and CPU time. I've already done all the usual T/S'ing: Started profile from scratch, compacted folders, re-indexed, newer faster computer, etc.. Still, this users' imapd process is always using the most CPU on the server. For troubleshooting, we setup another user which has more usage, folders, etc.. than he does, but we don't see the users process taking up most of the CPU with the imapd process. So, it almost sounds like a particular email may be the culprit, but how can we find it, if thats the problem? This has been going on for a while, and he is a management person, so his patience is about to end. Does anyone have any ideas?

  Read the article

• Ubuntu 12.10 64bit host reboots when trying to install any guest system using VirtualBox

  - by gts123

  I am having a really nasty problem with VirtualBox as everytime I try to install any guest OS(using ISO file as CD for installation media), the installation starts normally but as soon as it is about to start either installing to virtual hard drive or loading(e.g. as LiveFS) it causes the host system to reboot abruptly. Config is as below: Host system: Ubuntu 12.10 64bit - Intel® Core i7-2640M CPU @ 2.80GHz × 4 Virtualbox version: 4.1.18_Ubuntu r78361 Guest OS systems tried: 32bit version of FreeBSD 9, Debian 6, Tails 0.14 VM setup Tried to have the minimal setup necessary just in case it would avoid for each system to make sure I'd avoid conflicts, but to no avail. I've tried different values and combinations of the below but the problem still persists: Shared Clipboard: Disabled Show in fullscreen/seamless: Disabled Remember runtime changes: DIsabled Base Memory: 2048 MB Chipset: PIIX3 IO APIC: Disabled EFI: Disabled Absolute Pointing device: Disabled Processor(s): 1 CPU PAE/NX: Disabled VT-x/AMD-V: Disabled Video Memory: 12 MB 3d/2d acceleration: Disabled Storage IDE COntroller: PIIX3 (same as chipset instead of PIIX4) Use host I/O cache: No Audio: disabled Network adapter: NAT USB controller: disabled No shared folder Also another sideeffect of the reboot is that it appears that it does not log any information in the error log files; not making things any easier. Please help.

  Read the article

• What Windows service binds a NIC to the network?

  - by Bigbio2002

  I have a server that takes several minutes for the NIC to bind itself to the network upon startup (it has a statically-configured IP). This causes DNS/WINS/Intersite Messaging to fail to start, since they're dependent on a network connection. While I'm still attempting to find a root cause to this issue (I've done firmware updates, checked for any odd drivers/services, no luck so far), but in the meantime, I want to adjust the load order of services to ensure that the NIC binds first before these services attempt to start. The only question is, which service is it? The server is running Server 2008 R2 and only has one NIC installed. (On a side note, there are two other small but odd problems occuring with the server. The server had the issue described in KB2298620, which I've fixed. The other problem occurs in Windows Server Backup. No events appear in the upper portion of the window, despite the fact that backups are running in the background. Whenever I attempt to modify the backup schedule, it gives me the error "Not enough storage is available to process this command" and appears to fail, when, in fact, it actually succeeds. These may be separate issues, but something tells me that some of these might share a common root cause.)

  Read the article

• Retrieve a user's Exchange database in powershell

  - by Paul

  Hey Everyone, I've scoured the interwebs for a few days now off and on to find this. I am creating a powershell script for email-enabling new user's(Exchange 2007). To give you a little background when we have a new hire, their AD account is created at our off-site helpdesk, but they don't create their email account. I'm trying to automate the process of mail-enabling the user which involves putting them in the same database as an existing user, disable imap pop activesync, and lastly email the requester of the ticket. I would like to just get prompted for the New User's name, User to Replicate(mailbox, storage group, database), and the person to email after it's been created. So if someone could just help with a command to Retrieve a user's Exchange database in powershell that would be great, but if people also want to help with my hacked up script please do so as well!!! Here is what I have so far: Write-output “ENTER THE FOLLOWING DETAILS” $DName = Read-Host “User Diplay Name" $RUser = Read-Host "Replicate User(Database Grab)" ***$RData = #get the Replicate user's mailbox database here*** $REmail = #either just use a Read-Host “Requester's Email address" or ask for Requester's name and pipe through their email address by digging for it w/ powershell Enable-Mailbox -Identity "$DName" -Database "$RData" Send-MailMessage -From "John Doe <[email protected]>" -To (put $REmail here which is the Requester's email) -Subject "Test Person's email account" -Body "Test Person's email account has been setup.`n`n`nJohn Doe`nGeneric Company`nSystems Administrator`nOffice: 123.456.7890`[email protected]" -SmtpServer genericexchange.exchange.com

  Read the article

• central apache log analysis of many hosts

  - by Jason Antman

  We have 30+ apache httpd servers, and are looking to perform analysis on the logs both for historical trending and near "real time" monitoring/alerting. I'm mainly interested in things like error rates (4xx/5xx), response time, overall request rate, etc. but it would also be very useful to pull out more compute-intensive statistics like unique client IPs and user agents per unit of time. I'm leaning towards building this as a centralized collector/server/storage, and am also considering the possibility of storing non-apache logs (i.e. general syslog, firewall logs, etc.) in the same system. Obviously a large part of this will probably have to be custom (at least the connection between pieces and the parsing/analysis we do), but I haven't been able to find much information on people who have done stuff like this, at least at shops smaller than Google/Facebook/etc. who can throw their log data into a hundred-node compute cluster and run Map/Reduce on it. The main things I'm looking for are: - All open source - Some way of collecting logs from apache machines that isn't too resource-intensive, and transports them relatively quickly over the network - Some way of storing them (NoSQL? key-value store?) on the backend, for a given amount of time (and then rolling them up into historical averages) - In the middle of this, a way of graphing in near-real-time (probably also with some statistical analysis on it) and hopefully alerting off of those graphs. Any suggestions/pointers/ideas, to either "products"/projects or descriptions of how other people do this would be greatly helpful. Unfortunately, we're not exactly a new-age-y devops shop, lots of old stuff, homogeneous infrastructure, and strained boxes.

  Read the article

• Move files from ftp server to s3

  - by lev

  I would like to set up an ftp server, where users will upload files, and for each file, put it on s3 storage, and delete it from the ftp server. (the server runs on ec2 ubuntu) Here are the stuff I already tried, with no success.. Mount s3 bucket using s3fs. I followed those instructions, but there is a bug in the latest version of s3fs, that prevents it from working. The bug was fixed on the develop branch, but I don't want to use unstable version on my production. Use vsftpd and using s3cmd sync via cron to sync the files periodically. The problem with that approach, is that s3cmd can start running in the middle of a file upload, and start synching the incomplete file. Also s3cmd doesn't give any feedback it the sync fails, so I have no way of knowing if I can delete the files after the sync command finished running. Use pure-ftpd's upload script feature (which allows to run a script after a file is finished uploading), but I noticed that if the file upload was failed in the middle, the script will run anyway, and I have no way of knowing if the upload was successful or not. I've been at it for a few days now, and I'm at a loss here. Any suggestions will be welcomed.

  Read the article

• Large, high performance object or key/value store for HTTP serving on Linux

  - by Tommy

  I have a service that serves images to end users at a very high rate using plain HTTP. The images vary between 4 and 64kbytes, and there are 1.300.000.000 of them in total. The dataset is about 30TiB in size and changes (new objects, updates, deletes) make out less than 1% of the requests. The number of requests pr. second vary from 240 to 9000 and is dispersed pretty much all over, with few objects being especially "hot". As of now, these images are files on a ext3 filesystem distributed read only across a large amount of mid range servers. This poses several problems: Using a fileysystem is very inefficient since the metadata size is large, the inode/dentry cache is volatile on linux and some daemons tend to stat()/readdir() it's way through the directory structure, which in my case becomes very expensive. Updating the dataset is very time consuming and requires remounting between set A and B. The only reasonable handling is operating on the block device for backup, copying, etc. What I would like is a deamon that: speaks HTTP (get, put, delete and perhaps update) stores data it in an efficient structure. The index should remain in memory, and considering the amount of objects, the overhead must be small. The software should be able to handle massive connections with slow (if any) time needed to ramp up. Index should be read in memory at startup. Statistics would be nice, but not mandatory. I have experimented a bit with riak, redis, mongodb, kyoto and varnish with persistent storage, but I haven't had the chance to dig in really deep yet.

  Read the article

• Can Internet data be used by malware when PC off?

  - by Val

  I have noticed over the last month that my off peak data has been used at a rate of approx 350MB per hour - this has meant that I have gone over my quota and slowed down by my ISP to 256k. There is no one in the house using it (2am-8am is my ISPs off peak hours) at that time. My PC and other wireless devices (ipad and iphone) are turned off. I have changed the wireless password on my modem 3 times and it is now 30 digits long. So I don't think someone else is using my wireless access between 2-8am. It has been suggested by my ISP that I may have malware/spyware on my computer. Sorry for my ignorance, but can malware still run if the PC is off? I did look at my modem's log and followed an IP address to a service called Amazon Simple server Storage. Could this company possibly be the culprit? I am not too tech savvy, so any assistance appreciated. I have run a barrage of spyware cleaning software eg malware bytes; spy bot etc.... Cheers Val

  Read the article

• Array on servers which receive several hundred GB of data a day

  - by Matthew

  This is hopefully a simple question. Right now we are deploying servers which will serve as data warehouses. I know with raid 5 the best practice is 6 disks per raid 5. However, our plan is to use RAID 10 (both for performance and safety). We have a total of 14 disks (16 actually, but two are being used for OS). Keeping in mind that performance is very much an issue, which is better - doing several raid 1's? Do one large raid 10? One large raid 10 had been our original plan, but I want to see if anyone has any opinions I haven't thought of. Please note: This system was designed for using Raid 1+0, so losing half of the raw storage capacity is not an issue. Sorry i hadn't mentioned that initially. The concern is more whether or not we want to use one large Raid 1+0 containing all 14 disks, or several smaller raid 1+0's and then stripe across them using LVM. I know the best practice for higher raid levels is to never use more than 6 disks in an array.

  Read the article

• Whats the best cloud backup solution for a small scale server envoirnment?

  - by nbv4

  I have a server that runs a postgres database that contains about 200MB of data. Currently I have a cron job setup on my home computer which: ssh's into my server runs a remote script which makes a backup of the database scp's that dump over to my local hard drive for storage. Each dump is 20MiB. does this every six hours (one months of backups is roughly 2GiB) The problem with this setup is that if my local machine goes down for whatever reason, no backups will be made. Also, I can't have the cron run from the server, because I can't have it scp'd to my local machine from my server (firewalls and all that crap). My local machine is running Ubuntu 10.04, and my server is Ubuntu 9.10 server edition. I looked into Ubuntu One, but currently it's gui-only. I also looked into dropbox, but it's a pain in the ass to get setup in linux without gui support. Amazon S3 looks good but it's not free (yet dirt cheap). Is there any other alternative that I should look into? I'd prefer something where I can just have my script dump the database into a directory, and have the backup service 'watch' that folder and sync accordingly. I can maybe also have my local machine sync to the cloud backup so I have even more redundancy, plus easy access to my backups for use in testing.

  Read the article

< Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >