Search Results

Search found 7637 results on 306 pages for 'cd drives'.

Page 204/306 | < Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >

• Sorting out mSSD acceleration on a Acer M3-581TG

  - by PhonicUK

  I recently purchased a Acer Timeline M3 Ultra, it ships with a 500GB HDD and a 20GB mSSD to use as a cache. First thing I did when I got it was format the drives and install a clean OS (on the HDD, the mSSD has nothing on it) - but now I can't figure out how everything needs to be configured in order to use the mSSD as a cache, it just looks like a standard storage drive. I've poked around in the BIOS and there is a SATA mode setting, but it only has one option (AHCI), most of the documentation I've seen on the subject says that the SATA controller needs to be in RAID mode otherwise 'Acceleration' isn't visible in the Intel SRT menu (which for me, it isn't) I've seen a few things that suggest I just need the correct partition layout, I tried this using fdisk from a Linux LiveCD but got nowhere. Any ideas? The laptop shipped with no recovery media so I'm marginally stumped. I don't have any issue with reformatting again if required.

  Read the article

• Areca 1880ix RAID hangs

  - by Dave

  Areca RAID controller ARC-1880ix-12 (firmware 1.50) hangs when on high load. My setup is: Chenbro 3U chassis Intel S5500BC mainboard Xeon 5603 CPU 16GB of RAM 12 Seagate SAS drives ST32000645SS (2 of them as hot spare, 10 as RAID10) Mellanox Infiniband HBA card This server is working as external infiniband storage for Xen VMs. When load is quite big Areca's firmware hangs - it becomes unreachable even from Areca's ethernet adapter. After resetting the server power it returns to normal operation. While Areca is hanged I can confirm that it is powered (ethernet link is active) and Infiniband HBA works Ok. Thanks in advance for any idea or suggestion where the problem might be!

  Read the article

• How to save a document and close it after the save

  - by Le Questione

  Currently I have a .bat file that opens a program, opens a document and then reloads this document so it contains new data. After that I need a timeout so it can run some other things within the document which takes about 2 minutes in total, but for safety I used 5 minutes. Then I want it to save the document and close the program. I've searched a lot for this but I can't find anything that saves the document and then closes it. Only can find how to save a bat file, but I already have that! CD /D "D:\01 - Config\02 - Developer" start qv.exe /l "D:\02 - Content\07 - Accesspoint\tracktrace.qvw" timeout /t 300 ???? exit 0 Please advise, thanks

  Read the article

• Is there any Mac Pro hardware parts that can ONLY be purchased thru Apple?

  - by bigp

  I'd like to know if I need to be concerned about any hardware parts that I should include in a brand new Mac Pro purchase, instead of trying to hunt it down on 3rd party vendors (or whitelist vendors / hardware suppliers). The main components I'm interested for "upgradeability" are: Processors (If starting with Two 2.4GHz Quad-Core "Westmere"); RAM (If starting with the least possible, which seems to be 6 x 1GB); Video Cards (If starting with one ATI Radeon HD 5770, can a 2nd one be purchased elsewhere?) Hard-Drives (Since these are mounted in specialized trays [if I'm not mistaking], are they also sold elsewhere? And can they be bought as SSDs?) Power Supply (Do I need to be concerned about this at all, or does it auto-adjust depending on the new component upgrades?) I just want to be sure by choosing a Mac Pro with lower component specifications that I can in fact purchase upgrade parts cheaper elsewhere. Thanks!

  Read the article

• How to set up a PC which can be booted from Linux AND Windows?

  - by Martin

  Our PC was running Windows XP up to know. It has become incredibly slow and I'm considering switching to Linux (Ubuntu?!) as a fresh OS. However, there are some applications we rarely use which run only on Windows and I also want to have the possibility to easily go back to the old system, if I should find during testing linux, that anything is missing or not available. So the idea is to install Linux on a new (second) hard drive and use the existing Windows XP from a virtual machine (converted by Paragon Drive Backup) in the transition time. We have a lot of data on the PC, tens of GBs of Photos (managed by Picasa), ... My questions: What could be the best way to setup the new hard drive? (Partitions) I assume that I can not access the Linux data from Windows but I could access (read/write) windows drives from Linux? Does anyone know good tutorials for this use case? What other things might I have to consider for transition Windows-Linux?

  Read the article

• External stereo receiver and speakers on desktop PC work during test but no other time

  - by Debbie

  I have a desktop PC running Windows 7. I have connected an external stereo receiver and speakers to it and everything works fine when I test it in the Realtek Audio Sound through the control panel. However, when I play a video or an audio CD, the stereo speakers do not work. I have line in, line out, and speakers connected to the receiver. I have been through the configure speakers portion also. Is there someplace else I need to configure?

  Read the article

• Quake 3 won't install on Windows 7

  - by Ernest Friedman-Hill

  Today I tried to install Quake 3 from my original 1999 CD on a Windows 7 laptop. Windows 7 resolutely refused to run the installer, helpfully explaining that I might need a 32- or 64-bit version, depending on what my OS is (you have to love those Windows error messages: absolutely correct, but as unhelpful as humanly possible). In any case, of course the 1999 software is 32-bit, and the laptop is 64-bit. But I was pretty sure that 64-bit Windows versions could handle running 32-bit software. What gives?

  Read the article

• Resizing a System Partition Windows Server 2003 VM (Getting GParted Error)

  - by Dina

  I am getting an error while trying to resize System Partition for Windows 2003 Server (this is a VM on a Hyper-v Windows Server 2008) using GParted Live CD ISO. Followed this tutorial: http://malaysiavm.com/blog/how-to-resize-windows-2003-server-virtual-disk-on-vmware-esx/ and GParted Doc http://gparted.sourceforge.net/larry/resize/resizing.htm (They are very similar) The VM has a Dynamic VHD file, I have already increased it using Hyper-v. GParted doesn't give any clues or details for the error. Just simply errors when trying to grow the partition. Any ideas what I can do? Thanks! Using version of Gparted: gparted-live-0.13.1-2

  Read the article

• ext4: error loading journal

  - by cloudyOutside

  I have an external hard drive with two partitions: A small FAT32 which is mostly empty and works fine and a large ext4 with tons of data, most of which isn't backed up. The ext4 is visible, but can't be mounted. I get an "error loading journal" error. The drive is a Western Digital Caviar Blue 500GB. Roughly 30GB of that is FAT32 and the rest is the ext4. The light on the enclosure turns red when reading from the bad partition. It was made by Cavalry. There wasn't any warning, but coincidentally, I've been thinking lately that I should get two large capacity drives for real backups. Is there anything that can be done? I'm not even sure I have enough storage to backup everything even if it is redeemable.

  Read the article

• How can I switch Linux running OS from disk to running from RAM without restarting?

  - by vfclists

  Is it possible to switch to running Linux from RAM or RAM disk after starting starting initially from disk? eg. You need to make an image of your hard disk, FTP it to a remote location, some time later you want the image back, so you start the system from disk as usual, restore the image you FTP'd from the remote location back into place. More like a CloneZilla backup and restore, without booting the server from CD or USB disk, but starting from the normal hard disk? Notes on environment I should have mentioned it earlier. It is a remotely hosted VM where I cannot boot into a recovery console mode or do a netinstall. It will always boot onto the same disk. Which means that if there is some serious corruption I can't repair it offline, which is why being able to ftp a previously saved backup into place is so important

  Read the article

• Text template or tool for documentation of computer configurations

  - by mjustin

  I regularly write and update technical documentation which will be used to set up a new virtual machine, or to have a lookup for system dependencies in networks with around 20-50 (server-side) computers. At the moment I use OpenOffice Writer with text tables, and create one document per intranet domain. To improve this documentation, I would like to collect some examples to identify areas where my documents can be improved, regarding general structure and content, to make it easy to read and use not only for me but also for technical staff, helpdesk etc. Are there simple text templates (for example for OpenOffice Writer) or tools (maybe database-driven) for structured documentation of a computer configuration? Such a template / tool should provide required and optional configuration sections, like 'operating system', 'installed services', 'mapped network drives', 'scheduled tasks', 'remote servers', 'logon user account', 'firewall settings', 'hard disk size' ... It is not so much low-level hardware docs but more infrastructure / integration information in these documents (no BIOS settings, MAC addresses).

  Read the article

• VIM is great for text. Is there, too, an efficient, mouseless way to manipulate files on OS X?

  - by Dokkat

  I am having trouble navigating through files on OS X. That is, creating files, copying, moving, and so on. I am currently using the Finder, but the act of clicking with the mouse is not very efficient. Acessing a deep folder takes a considerable amount of time and you'll have to know it's entire path. When I try to use the command line it is even worse. Going to a folder requires at least typing it's entire path with the 'cd' command; and, when you are there, you don't have full control over it. For example, how would you move 3 specific files to another folder? Some text editors offer a 'fuzzy search' function that allows a very fast form of jumping through files. What is a fast, efficient way to navigate through files on OS X?

  Read the article

• Big noise from Power Supply Unity Fa? Should I replace it immediately?

  - by EApubs

  Recently, I started to get a large noise from my PC when switched on. After some time, it disappears. I discovered that the issue is with the Power Supply Unit. Does this mean I have a failing PSU? Will it harm the PC if I didn't replace it immediately? Several years ago I bought a new computer casing which is very weird. Its small and compact. Normally, we have the PSU in the top. But in here, the PSU is on the bottom and right below the hard drive. Recently, two of my hard drives started to show problems. Read errors and bad sectors. Can it be the PSU and the design of the casing? Here's an image of the PSU and the hard drive :

  Read the article

• Add a netbook to an existing Windows XP home network

  - by GorillaSandwich

  I've got a home network set up with a couple of Windows XP computers. I'm now trying to add our new netbook to it - also running XP. (The goal is to share files and a printer.) I have run the Network Setup Wizard and made sure that the workgroup name is the same as the others, and have rebooted several times, but whenever I try to 'view workgroup computers,' the only one on it is the netbook. I have a Windows XP CD, but the netbook has no drive. The wizard has some options for floppy disks, but that's useless to me these days. What is this wizard actually trying to do, and can I do it manually? Surely it can't be this hard.

  Read the article

• Simple Ubuntu Server - Expanding disk space - adding a new drive LVM, RAID0 existing setup - how?

  - by NightWolf

  I have a 1TB ext4 partition mounted at / with all my data and Ubuntu 11.04 (natty) installed. Now this drive is almost full (I used it as a database server for some processing). RAID0 is ok, I can take a failure (touch wood). But I need a way to grow this partition. I have a new 1TB drive I want to add, however as my Ubuntu boot and all data is on the one partition I'm not sure how I can go about setting up a RAID0 or LVM array without loosing all my data. So the question is how can I extend my existing ext4 partition over two physical drives without losing data? Thanks!

  Read the article

• Small business VPN solution

  - by Crash893

  I've been looking for a while but I'd like to to implement a vpn solution for anywhere from 1-5 employees at a time (possibly 10 in a year or so) edit: Basically I would like outside users to fire up a client or open a web page and be able to access things inside the company network (share drives / printers/ webapps /etc) I've looked at Astaro Gateway but im not sure if that's the right tool for the job. I know "best" is a subjective term so i would like to break it into to different suggestions 1) what is the cheapest solution given the criteria above 2) what solution will result in the least amount of headaches from the point of view of maintenance and learning curve.

  Read the article

• How can I accurately determine the age of a hard drive?

  - by Todd Stout

  Yes, if it's large, heavy, and only 65 Meg in capacity, you can assume it's ancient. An RLL controller would positively indicate the drive is from antiquity. What about drives that are only 3 or 4 years old? If I know the serial number, make and model is there a public database that indicates a manufacturing date? Update: As trite as this question might seem to some, the hard drive I was looking at that precipitated this question had no obvious manufacturing date stamped on it. I realize that most do. I think the answers given are very useful to myself and others.

  Read the article

• Notification if SyncToy fails

  - by Joel Coehoorn

  I support a number of laptop users. In the past (before there were many laptops), each user's computer was set up so that their My Documents folder was mapped to a shared folder on the server. This worked very well for desktops, but has several obvious downsides for laptops (no files when you're off-site, etc). I'm exploring several alternatives for laptops to better map the shared drives, and SyncToy seems the best so far. I have a couple trial users set up so that it syncs automatically whenever they log in, along with a desktop icon they can click if they know they'll need something saved before the next login. My problem is that I'm concerned how I, as the maintainer of this system, can spot failures. I don't want my first indication of a problem to come after a user drops their laptop in a lake and it turns out nothing was synced for the last year. Any ideas?

  Read the article

• Cannot acess the new cloned server even after new IP address assignment

  - by tough

  I was able to clone a Ubuntu 10.04 server residing in Cloud. It appeared that I was not getting some IP for the new VM so I followed some of these: # cd /etc/udev/rules.d # cp 70-persistent-net.rules /root/ # rm 70-persistent-net.rules # reboot I didn't follow the later commands as I was unable to see two eth MACs as available in the referenced site. After this I am able to see some the IP for it, and is different form the original IP, I have added new IP to DNS server. Now when I try to access it with its assigned(new) domain it is directed to the old server. I can see both the VMs running with different IP. Where I might have gone wrong, I am new to this admin thing.

  Read the article

• How to install Windows 7 on Acer Aspire iDea 500?

  - by Martin R-L

  I've got a Windows 7 Ultimate 32-bit from MSDN Subscriber Downloads. The downloaded ISO boots fine from both a USB pen drive and a DVD on other computers. On the Acer it doesn't boot. The Acer iDea 500 can boot, and install, Windows XP Mediacenter from a DVD with slipstreamed SATA drives on it. Also, all kinds of Linux distros works perfectly fine on the iDea 500. I wouldn't mind using Mythbuntu instead of Windows 7 Ultimate, but it doesn't work very well.

  Read the article

• Network DFS Shares Jumping Back To Root

  - by Taz

  We map several network drives to DFS locations via a logon script. Recently we've had a number of users complain of a very unusual behaviour when navigating these shares. They will be going through folders and will get 'rubber-banded' back to the root of the share. This will happen for a few minutes and then go back to behaving normally. The users are on Windows 7 and the fileshare is on Windows Server 2K8R2. Any idea what could be causing this annoying behaviour?

  Read the article

• Problems when loop over a series of ssh-ed commands

  - by Jack Medley

  I have a series of server machines which I want to run the same command on. Each command takes hours and (even though I am running the commands using nohup and setting them to run in the background) I have to wait for each to finish before the next starts. Here is roughly how I have set it up: On the host machines: for i in {1..9}; do ssh RemoteMachine${i} ./RunJobs.sh; done Where RunJobs.sh on each remote machine is: source ~/.bash_profile cd AriadneMatching for file in FileDirectory/Input_*; do nohup ./Executable ${file} & done exit Does anyone know of a way such that I dont have to wait for each job to finish before the next starts? Or alternatively a better way of doing this, I have a feeling what I am do is fairly sub-optimal. Cheers, Jack

  Read the article

• Setting Linux UID on NFS volume from EMC NX4

  - by ethrbunny

  I have an EMC NX4 from which there are several CIFS shares with corresponding NFS mount points. The CIFS user ids seem fine but when viewed from Linux they are all 327xx numbers and can't be set from the file system. (IE CHOWN doesn't work - permission denied). On our other (older) EMC devices we used an MMC app to set the Linux UID for each user. I don't seem to have such an app on the 'Applications and Tools' CD for this new device. Is there some other method for setting these? Did I setup the system incorrectly?

  Read the article

• How to resize a ubuntu partition to make more room for windows

  - by Jeremy

  My laptop has Windows 7 and Ubuntu 13.10 installed alongside each other. My laptop has two 225GB hard drives. I give Ubuntu 133.65GB and I give Windows 87.76GB on the same hard drive (C). My problem now is that Windows is almost out of space but Ubuntu is only using a few GB of the 133.65GB that I gave it. I want to reduce Ubuntu's partition size and give that space to increase Windows partition size. Is that any program that can to do this?

  Read the article

• Accessing WindowsXP shared printer from macbook?

  - by mobibob

  My new printer is setup on WindowsXP, it works and it is configured as a shared printer. I then setup a printer from Mac OSX 10.6.3 using the approved driver from the setup CD. I browsed for the printer via the network. When I send a test page, it queues, but never prints. Its as if the driver thinks the printer is local to the mac and just never finishes printing. THe configuration shows as: smb://dragoneye/CanonMP2 Where dragoneye is the name of the Windows XP server and the CanonMP2 is the little multi-purpose printer. My other Windows' CPU can setup and print. Is this a known problem or am I missing a setting??

  Read the article

< Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >