Search Results

Search found 7325 results on 293 pages for 'windows7 32'.

Page 204/293 | < Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >

• 3GB RAM Installed and Detected by BIOS, Windows Vista 32bit Only Sees 2GB

  - by Nathan Taylor

  I am attempting to install more RAM on a Windows Vista 32bit machine which is using a X6DAL-XG motherboard and the RAM amount reported in the BIOS is 3GB+, but Windows is only reporting 2GB installed. The motherboard has 6 RAM bays which I have populated with various combinations of 4 1GB sticks, and 2 512mb sticks, but no matter how I configure them Windows doesn't see more than 2GB. I realize of course 32-bit Windows has a 3gb cap on memory, but that doesn't explain why it will only report 2GB when there are in fact (currently) 5GB installed. I should think I would be able to see at least 3GB. According to the spec list for the motherboard the minimum RAM requirements are DDR333/266mhz installed in pairs. I have done this exactly, and the BIOS isn't reporting any problems at POST. RAM Configuration (according to CPU-Z): Slot #1: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #2: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #3: PQI - 512mb PC2700 (166mhz) Slot #4: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #5: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #6: PQI - 512mb PC2700 (166mhz) I'm not sure if memory specs above conflict with this statement in the motherboard manual or not: Memory Support The X6DAL-XG supports up to 12GB/24GB of registered ECC DDR333/266 (PC2700/PC2100) memory. The motherboard was designed to support 4GB (PC2100) modules in each slot, but only the 2GB modules have been tested. When using registered ECC DDR333 (PC2700) memory, installing four pieces of double-banked memory or six pieces of single-banked memory is supported. So, am I doing something wrong with the RAM I have now, or is there some sort of compatibility problem which I am missing? Thanks!

  Read the article

• How can I fix my corrupted RAID1 ext4 partition on a Synology DS212 NAS?

  - by Neil

  I have two identical 3 TB disks that were in a RAID1 array, where one disk crashed. I replaced the failed disk, but not after the RAID partitions got messed up. I need to figure out how to restore the RAID array and get at my ext4 partition. Here are the properties of the surviving disk: # fdisk -l /dev/sda fdisk: device has more than 2^32 sectors, can't use all of them Disk /dev/sda: 2199.0 GB, 2199023255040 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 267350 2147483647+ ee EFI GPT # parted /dev/sda print Model: ATA ST3000DM001-9YN1 (scsi) Disk /dev/sda: 3001GB Sector size (logical/physical): 512B/512B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 131kB 2550MB 2550MB ext4 raid 2 2550MB 4698MB 2147MB linux-swap(v1) raid 5 4840MB 3001GB 2996GB raid I replaced the failed drive, and cloned the surviving drive to it so I have something to work with. I cloned the drives with dd if=/dev/sdb of=/dev/sda conv=noerror bs=64M, and now /dev/sda and /dev/sdb are identical. Here is the RAID information: # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] md1 : active raid1 sdb2[1] 2097088 blocks [2/1] [_U] md0 : active raid1 sdb1[1] 2490176 blocks [2/1] [_U] unused devices: <none> It seems that md2 is missing. Here is what testdisk 6.14-WIP finds: Disk /dev/sda - 3000 GB / 2794 GiB - CHS 364801 255 63 Current partition structure: Partition Start End Size in sectors 1 P Linux Raid 256 4980735 4980480 [md0] 2 P Linux Raid 4980736 9175039 4194304 [md1] Invalid RAID superblock 5 P Linux Raid 9453280 5860519007 5851065728 5 P Linux Raid 9453280 5860519007 5851065728 # After a quick search Disk /dev/sda - 3000 GB / 2794 GiB - CHS 364801 255 63 Partition Start End Size in sectors D MS Data 256 4980607 4980352 [1.41.12-2197] D Linux Raid 256 4980735 4980480 [md0] D Linux Swap 4980736 9174895 4194160 D Linux Raid 4980736 9175039 4194304 [md1] >P MS Data 9481056 5858437983 5848956928 [1.41.12-2228] And listing the files on the last partition in the list shows all of my files intact. What should I do?

  Read the article

• Address (url) forwarding with Vyatta

  - by Trikks

  Got this kind of noob question i suppose. I got this very basic network setup and need help to set up some address forwarding. As seen in my illustration below all traffic enters via the eth0 interface (85.123.32.23). The external dns is setup to direct all hosts to this ip as well. Now, how on earth do I filter the incoming requests to each box? The Ip's are static! My network layout: I do not wish to solve this by assigning tons of ports etc. In my wishful thinking something like this would be nice :) set service nat rule 10 type destination set service nat rule 10 inbound-interface eth0 set service nat rule 10 destination address ftp.myhost.com set service nat rule 10 inside-address address 192.168.100.20 This way ALL traffic to the address ftp.myhost.com (at eth0) should be routed to the internal ip, 192.168.100.20. Right, is there anyone who could point in some direction? Maybe it's wrong to use nat? Please help me! :)

  Read the article

• Getting 400 Bad Request when requesting by server name on nginx/uwsgi

  - by Marc Hughes

  I'm trying to run 2 different sites on nginx via different ports (they each have a load balancer that points to the appropriate port). The first site work perfectly. The second site... If I access http://localhost:81/ it works correctly If I access http://127.0.01:81/ it works correctly If I access the hostname http://THEHOSTNAME:81/ it fails with a 400 error If I access the public IP http://x.x.x.x:81/ it fails with a 400 error I've set the error_log to info, but the only lines I get in the log when this happens is: ==> /var/log/nginx/access.log <== 10.183.38.141 - - [24/Aug/2014:21:03:28 +0000] "GET / HTTP/1.1" 400 37 "-" "curl/7.36.0" "-" ==> /var/log/nginx/error.log <== 2014/08/24 21:03:28 [info] 7029#0: *5 client 10.183.38.141 closed keepalive connection In my uwsgi log, I only see this: [pid: 6870|app: 0|req: 87/92] 10.28.23.224 () {32 vars in 380 bytes} [Sun Aug 24 21:05:21 2014] GET / => generated 26 bytes in 1 msecs (HTTP/1.1 400) 2 headers in 82 bytes (1 switches on core 2) What should be my next step in debugging this?

  Read the article

• Can't install Visual Studio 2010 SP1 from an .ISO file I downloaded. Error inside

  - by Sergio

  This is the error: [Window Title] C:\Users\Sergio\Desktop\Things\Setup.exe [Content] The version of this file is not compatible with the version of Windows you're running. Check your computer's system information to see whether you need an x86 (32-bit) or x64 (64-bit) version of the program, and then contact the software publisher. [OK] I'm running Windows 7 (64bit) Ultimate and have installed this service pack before (2 days ago) on another machine with similar specs and the same exact OS software. I've tried mounting the .ISO file to a virtual drive and installing from there and I get that error. I've tried mounting the .ISO and copy pasting the files to a local folder on my drive and then running the setup.exe application, and I get that error. I don't know how to proceed but can provide any additional information you require from me. What can I do to fix this? Edit If I right click Setup.exe and Run As Administrator, I get the following error: [Window Title] C:\Users\Sergio\Desktop\Things\Setup.exe [Content] Windows cannot find 'C:\Users\Sergio\Desktop\Things\Setup.exe'. Make sure you typed the name correctly, and then try again. [OK] I've already tried re downloading the ISO from the site, but a quick check of the bytes of the file assures me that the ISO on my drive is 100% correctly downloaded. I get the same amount of bytes in size from the downloading ISO (as Opera reports).

  Read the article

• HP ProCurve & Cisco switches interoperability

  - by Kamil Z

  I have a couple of questions regarding Cisco and HP ProCurve interoperability. Here's a link to pdf with my network topology. Can someone help me with basic VLAN configuration in such topology? Below there are some details of my configuration: # m_management_2 interface FastEthernet0/43 switchport access vlan 250 switchport mode access spanning-tree port-priority 32 spanning-tree cost 100 # MTA2-swmgmt1 vlan 1 name "DEFAULT_VLAN" untagged 1-48 ip address 10.10.249.190 255.255.255.128 exit # MTA2-swtr1 vlan 1 name "DEFAULT_VLAN" untagged 1-14,16-48 no ip address no untagged 15 exit vlan 100 name "MTA Mgmt" untagged 15 ip address 10.10.249.188 255.255.255.128 exit # MTA2-swtr2 vlan 1 name "DEFAULT_VLAN" untagged 1-14,16-48 no ip address no untagged 15 exit vlan 100 name "MTA Mgmt" untagged 15 ip address 10.10.249.189 255.255.255.128 exit I don't post MTA2-bcsw[12] configuration, because I wasn's successfull in this one yet. Every time I configure VLANs on MTA2-bcsw[12] Fa0/24 interface on m_management_2 goes down bacause of receiving tagged BPDUs on access port (there are no VLANs configured on MTA2-swmgmt1 because of fact that only 250 VLAN is allowed in this switch. Is it correct?). Can someone provide me some basic configuration for this topology? Second thing I want to ask is concept of connection from MTA2-swmgmt1 to MTA2-swtr[12] HP switches for the sake of management. How to configure such ports on HP switches (managed switch and manager switch). Is my actual configuration correct?

  Read the article

• How do I improve my incremental-backup performance?

  - by Alistair Bell

  I'm currently using the traditional rsync+cp -al method to create incremental/snapshot backups of our server tree. The backups are going onto a pair of eight-disk towers connected to the backup machine (a Sandy Bridge machine with 16 GB of RAM, running CentOS 5.5) via four eSATA connections (four disks per connection). Each disk is a regular 2 TB disk, so we have 32 TB of disk space connected to the backup machine. We're backing up about 20 TB of data on the servers with this. The problem is that each daily backup is taking more than 24 hours, and the real time-killer isn't the actual rsync, but the time it takes to perform a cp -al of the tree locally on the backup machine. It's taking more than 12 hours just to make the shadow copy of the tree, and as far as I can tell the performance backlog is at the disk (top shows the cp using a lot of RAM but not a lot of CPU and mostly in uninterruptible-sleep state) We have the server data split into four major volumes (and a few minor ones), and each of these backups runs in parallel (with some offsets in the cron to try to get some disks' cp done first). There are two volumes on the backup drive, both striped LVM volumes of 16 TB each. So obviously I need to improve the performance because it's unusable as it stands. The first question is: when CentOS 6 comes out, with support for btrfs, will making snapshots of subvolumes with btrfs substantially increase this performance? The second is: is there a way, with ext3 or something else supported in CentOS 5 or 6, to 'encourage' it to put the directories/inodes in one part of a volume (which could happen to be the part that's on an SSD, via LVM) and the files in another? That would presumably solve the problem, but I don't know of ways to hint ext3 like that.

  Read the article

• Is it possible to shrink the size of an HP Smart Array logical drive?

  - by ewwhite

  I know extension is quite possible using the hpacucli utility, but is there an easy way to reduce the size of an existing logical drive (not array)? The controller is a P410i in a ProLiant DL360 G6 server. I'd like to reduce logicaldrive 1 from 72GB to 40GB. => ctrl all show config detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: 5001438006FD9A50 Cache Serial Number: PAAVP9VYFB8Y RAID 6 (ADG) Status: Disabled Controller Status: OK Chassis Slot: Hardware Revision: Rev C Firmware Version: 3.66 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Queue Depth: Automatic Monitor and Performance Delay: 60 min Elevator Sort: Enabled Degraded Performance Optimization: Disabled Inconsistency Repair Policy: Disabled Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Enabled Total Cache Size: 512 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 412476 MB Status: OK Logical Drive: 1 Size: 72.0 GB Fault Tolerance: RAID 1+0 Heads: 255 Sectors Per Track: 32 Cylinders: 18504 Strip Size: 256 KB Status: OK Array Accelerator: Enabled Unique Identifier: 600508B1001C132E4BBDFAA6DAD13DA3 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 196 MB, / 12.0 GB, /usr 8.0 GB, /var 4.0 GB, /tmp 2.0 GB OS Status: LOCKED Logical Drive Label: AE438D6A5001438006FD9A50BE0A Mirror Group 0: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 146 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 146 GB, OK) SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 Device Number: 250 Firmware Version: RevC WWID: 5001438006FD9A5F Vendor ID: PMCSIERA Model: SRC 8x6G

  Read the article

• How can I calculate power consumption of my PC in Watt?

  - by Jitendra vyas

  How can I calculate power consumption of my PC in Watt, to prove my House owner ( I live on rent) , my PC doesn't consume much power? He blames me for Huge power bills even he too use Fridge, A.C. etc and his son watch the TV all the time. We both share one Power meter so for bill we pay 50%-50% but He is saying I use PC all the time even night i keep on for downloading. I just want to calculate power consumption of my PC then will calculate monthly expense of unit as per my City's per unit price for power. I've Windows: Microsoft Windows XP Professional 5.1.2600 Service Pack 3 Memory (RAM): 960 MB CPU Info: AMD Sempron(tm) Processor 2500+ CPU Speed: 1399.0 MHz Sound card: Vinyl AC'97 Audio (WAVE) Display Adapters: VIA/S3G UniChrome Pro IGP | NetMeeting driver | RDPDD Chained DD Monitors: 1 - 17inch LCD - LG Screen Resolution: 1280 X 768 - 32 bit Network: Network Present Network Adapters: Bluetooth Device (Personal Area Network) #2 | WAN (PPP/SLIP) Interface CD / DVD Drives: I: ELBY CLONEDRIVE COM Ports: COM1 | COM2 | COM7 | COM8 | COM9 | COM10 LPT Ports: LPT1 Mouse: 3 Button Wheel Mouse Present Hard Disks: C: 29.3GB | D: 29.3GB | E: 97.7GB | F: 97.7GB | G: 211.9GB USB Controllers: 5 host controllers. Firewire (1394): 1 host controllers. Manufacturer: Phoenix Technologies, LTD Product Make: MS-7142 AC Power Status: OnLine BIOS Info: AT/AT COMPATIBLE | 01/18/06 | VIAK8M - 42302e31 Motherboard: MICRO-STAR INTERNATIONAL CO., LTD MS-7142 Modem: ZTE USB Modem FFFE CDMA #2

  Read the article

• socket problem with MySQL

  - by Hristo

  This is a recent problem... MySQL was working and a couple of days ago I must have done something. I deleted MySQL and tried reinstalling using the .dmg file. The mysql.sock file never gets created and I get the following error messages: Hristo$ mysql Enter password: ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/mysql/mysql.sock' (2) I also tried stopping Apache and installing but Apache gave me an error... I don't know if this is good or bad: Hristo$ sudo apachectl stop launchctl: Error unloading: org.apache.httpd I tried the MacPorts installation as well but the socket file still didn't get created. I don't really know what to do and I don't want to reinstall Snow Leopard and start from scratch :/ I also tried installing the 32-bit version and same deal. No luck. Finally... I tried doing the source installation but when I get to the configuration step, I get the following error: -bash: ./configure: No such file or directory The file is "mysql-5.1.47-osx10.6-x86_64.tar.gz" so I think it is the proper file for source installation and yes I have a 64 bit system. I don't know what to do anymore. Any ideas? Thanks, Hristo

  Read the article

• USB Wifi will not connect on Windows 7 (Even though the driver installs OK)

  - by Pete Roberts

  Windows 7 will not connect to a WiFi Netowrk using a USB Network Adapter. I have 3 adapters, A Senoa SUB 364 (EXT), a Repeatit SU2410 USB V2 and a ZYXEL G202. All of these devices install OK on Windows 7 Home Premium on my Destop PC (64 bit) and on my Asus Wii Netbook (32 bit). In each case the adapter can be enabled/disabled and the driver properties says it is working correctly. When I try and connect to a network Windows 7 behaves as though the adapter does not exist and reports no networks. The Wii has an integrated adapter which works perfectly under Windows and connects to either of the 3 networks available to me. I have done all the checks I can on the configuration. What seems odd to me is that it happens to all 3 devices on 2 different windows 7 PCs both of which are working perfectly in any other respect. This suggests the common denominator is me and I must be doing something wrong.. what's also strange is that I cannot find any similar problems being reported on any of the forums. From what reading I've been able to do it seems like the new wifi virtualisation thingy in W7 is not recognising the adapters which suggests I', missing a configuration option somewhere. Looking forward to finding out if I'm not alone or just being stupid. Pete

  Read the article

• Laptop choice for development: MacBook Pro 17 vs Dell Studio XPS 16 vs HP Envy 15

  - by Shalan

  Hey! First things first - let me state that I am not intending to play games on this - I have narrowed down to these 3 purely based on specs and its individual brand reliability in the market. I intend to primarily use: Visual Studio 2008 Pro a lot (develop and deploy on Windows platforms) SQL Server 2005 Oracle 10g Adobe Photoshop CS4 Microsoft Expression Studio Google Sketchup I currently use a desktop PC (Core2Duo 2.66Ghz with 3GB DDRII memory) running Vista Business 32-bit - and I have to admit that, especially for Visual Studio, its quite sluggish to a point where it affects productivity. Furthermore, I intend to only use the notebook on a table - with a cooled surface, like granite :) - so I would appreciate people's input with regard to heat issues. Im aware that the Dell's primary exhaust gets blocked by the lid when open, but some reviews don't seem to place extraordinary emphasis on heat issues resulting from this. My options for the Dell/Alienware: Core i7 720QM 4GB DDRIII memory ATI mobility 3670 (512) 128GB Solid State Drive 16-inch Full HD RGB-LED LCD display (1080p) 3-year next-business-day support My configuration for the Apple MBP: Core2Duo 2.8Ghz (Im assuming the T9600) 4GB DDRIII memory 128GB Solid State Drive standard 1 year support The one advantage I think of with the MBP is that I can have the addition of OSX (though Im unsure what I would use it for, but purely to play around with a much-boasted-about OS) What are your thoughts on this, especially regarding build-quality, heat, performance and battery-life? Much thanks! ~shalan

  Read the article

• High mysql server load, sar output

  - by eric

  I have a MySQL Server that should be performing better than it seems to be. We're running ubuntu on a Amazon Cluster Compute (cc1.4xlarge) Linux ip-10-0-1-60 3.2.0-25-virtual #40-Ubuntu SMP Wed May 23 22:20:17 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise I have several output files from sar that i'm not really sure how to interpret. For example, I ran: # Individual block device I/O activities sar -d 1 180 > logs/block_device_io.log & which gave me what looks like really high utilisation of my disk (turns out this block device maps to /dev/xvdh on /var/lib/mysql type ext4 (rw,_netdev) The output from my log: 10:48:59 PM DEV tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util 10:49:00 PM dev202-16 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 10:49:00 PM dev202-32 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 10:49:00 PM dev8-0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 10:49:00 PM dev202-112 1008.00 31040.00 1416.00 32.20 1.02 1.01 0.89 90.00 10:49:00 PM dev202-80 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 Am I wrong in thinking this is a problem? I have it above 90% almost the entire time we're seeing slowness. Or does this just mean MySQL is doing what it's supposed to do?

  Read the article

• Disabling CPU management

  - by Tiffany Walker

  If I add the following processor.max_cstate=0 to the kernel command line for boot up, does that disable all CPU power management and throttling? I also found: http://www.experts-exchange.com/OS/Linux/Administration/A_3492-Avoiding-CPU-speed-scaling-in-modern-Linux-distributions-Running-CPU-at-full-speed-Tips.html The link talks of Change CPU governor from 'ondemand' to 'performance' for all CPUs/cores and disabling kondemand from kernel. Server is for web hosting UPDATES: 2.6.32-379.1.1.lve1.1.7.6.el6.x86_64 #1 SMP Sat Aug 4 09:56:37 EDT 2012 x86_64 x86_64 x86_64 GNU/Linux . # dmidecode 2.11 SMBIOS 2.6 present. 74 structures occupying 2878 bytes. Table at 0x0009F000. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: American Megatrends Inc. Version: 1.0c Release Date: 05/27/2010 Address: 0xF0000 Runtime Size: 64 kB ROM Size: 4096 kB Characteristics: ISA is supported PCI is supported PNP is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 kB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Targeted content distribution is supported BIOS Revision: 8.16 Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: 0123456789 UUID: 49434D53-0200-9033-2500-33902500D52C Wake-up Type: Power Switch SKU Number: To Be Filled By O.E.M. Family: To Be Filled By O.E.M. Handle 0x0002, DMI type 2, 15 bytes Base Board Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: VM11S61561 Asset Tag: To Be Filled By O.E.M. Features: Board is a hosting board Board is replaceable Location In Chassis: To Be Filled By O.E.M. Chassis Handle: 0x0003 Type: Motherboard Contained Object Handles: 0 Handle 0x0003, DMI type 3, 21 bytes Chassis Information Manufacturer: Supermicro Type: Sealed-case PC Lock: Not Present Version: 0123456789 Serial Number: 0123456789 Asset Tag: To Be Filled By O.E.M. Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00000000 Height: Unspecified Number Of Power Cords: 1 Contained Elements: 0

  Read the article

• r1soft agent is failing with the error: "write error while sending code: Broken pipe"

  - by curiousguy

  I have an Ubuntu 10.04.4 LTS server with r1soft agent installed in it. Recently, the backups are failing with the following error. -------- write error while sending code: Broken pipe -------- I have reinstalled the buagent but to no avail. On checking the server logs, I could see the following errors listed in it: -------- # tail -f /var/log/messages |grep -i buagent Nov 17 03:35:06 microscope buagent: Need to back up 126 sectors Nov 17 03:35:06 microscope buagent: (Righteous Backup Linux Agent) 1.79.0 build 12433 Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.195) with valid RSA key Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.201) with valid RSA key Nov 17 03:35:06 microscope buagent: sending auth challenge for allowed host at (10.128.136.201) port (47890) Nov 17 03:35:06 microscope buagent: host (10.128.136.201) port (47890) authentication successful Nov 17 03:35:06 microscope buagent: Backup request accepted. Starting backup. Nov 17 03:35:06 microscope buagent: Snapshot completed in 0.010 seconds. Nov 17 03:45:03 microscope buagent: Error reading blocks from snapshot. Nov 17 03:45:03 microscope buagent: Reading blocks failed Nov 17 03:45:03 microscope buagent: error backup aborted Nov 17 03:45:03 microscope buagent: backup failed on agent closing connection Nov 17 03:45:03 microscope buagent: Backup failed. Nov 17 03:45:03 microscope buagent: write error while sending code: Broken pipe (32) Nov 17 03:45:03 microscope buagent: tell child write failed -------- I tried changing the 'Timeout' and 'DiskAsPartition' value in '/etc/buagent/agent_config' file but no luck. Also, verified that proper route is added to the backup server. The agent is also running fine. Am I missing anything? Any help would be much appreciated. Note: CDP 2.0 is installed in the backup server.

  Read the article

• Windows Terminal Server: occasional memory violation for applications

  - by syneticon-dj

  On a virtualized (ESXi 4.1) Windows Server 2008 SP2 32-bit machine which is used as a terminal server, I occasionally (approximately 1-3 event log entries a day) see applications fail with an 0xc0000005 error - apparently a memory access violation. The problem seems quite random and only badly reproducable - applications may run for hours, fail with 0xc0000005 and restart quite fine or just throw the access violation at startup and start flawlessly at the second attempt. The names of executables, modules and offset addresses vary, although a single executable tends to fail with same modules and the same memory offset addresses (like "OUTLOOK.EXE" repeatedly failing on module "olmapi32.dll" with the offset "0x00044b7a") - even across multiple user's logons and with several days passing without a single failure inbetween. The offset addresses seem to change across reboots, however. Only selective executables seem affected by the problem, although I may simply not be seeing a sufficient number of application runs from the other ones. I first suspected a possible problem with the physical machine's RAM, but ruled this out as a rather unlikely cause - the memory comes with ECC and I've already moved the virtual machine across several times, without any perceptable change. I've seen that DEP was enabled in "OptOut" mode on this machine: C:\Users\administrator>wmic OS Get DataExecutionPrevention_SupportPolicy DataExecutionPrevention_SupportPolicy 3 and tried changing the policy to OptIn via startup options: bcdedit.exe /set {current} nx OptIn but have yet to see any effect - I also would expect Outlook 12 or Adobe Reader 9 (both affected applications) to play well with DEP. Any other ideas why the apps may be failing?

  Read the article

• Selenium server causes crazy load on server - how to prevent?

  - by Eric

  I'm running this linux: Linux host.themepark.com 2.6.32-220.4.1.el6.x86_64 #1 SMP Tue Jan 24 02:13:44 GMT 2012 x86_64 x86_64 x86_64 GNU/Linux And I run the Selenium stand-alone server on my box with this command: java -jar /home/l/cron/selenium-server-standalone-2.24.1.jar > /logs/selenium.log 2>&1 & Here's the problem: as soon as I do that, the server load starts skyrocketing. I even went back and downloaded older versions of the Selenium server, but same results with 2.23.1, 2.23.0, and 2.19.0. Note that the server load starts going nuts before I issue ANY commands to Selenium or do anything else. All I'm doing is firing up the server, per the command above. This used to work perfectly on my server without causing massive server load, so something has changed, but I'm not sure what. My server is a managed VPS so I don't know if there is some kind of auto-update script that kicked in or what... but it's a problem. (Incidentally, even though the server load climbs like crazy, everything still works: after firing up Selenium, my server creates a screen with Xvfb so Firefox will be happy, then a PHP script talks to Selenium to do what it needs to do before shutting everything down. It takes a LONG time, and the load gets all the way up to 8 [!!!] before it is finished, which kills my web server and makes the main site horribly unresponsive... but it does get everything done.) Any suggestions for what is going on, why it's started doing this and/or, most importantly, how I can make Selenium not kill the server when it starts up... would be GREATLY appreciated!

  Read the article

• Interpreting Inkscape SVG path coordinates for HTML map

  - by tovare

  I needed some coordinates for a HTML MAP and tried to use inkskape by opening the image and just draw a path with my polygon coordinates. My document properties are set to 256 x 256 pixels and units: px When opening the svg file i get coordinates which are not immediately apparent. <path style="fill:none;stroke:#000000;stroke-width:1px;stroke-linecap:butt; stroke-linejoin:miter;stroke-opacity:1" d="m 23.864407,126.91525 3.254237, 44.47458 35.79661, 44.47458 71.593216, 19.52542 71.59322, -37.9661 22.77967, -72.67797 L 218.0339, 64 192,49.898305 l -32.54237, 8.677966 -18.44068, -35.79661 1.08474, -17.3559322 -71.593215,0 L 45.559322,34.711864 35. 79661,57.491525 5.4237288, 74.847458 6.5084746,101.9661 23.864407,126.91525 z" id="path2840" /> How can I get coordinates I can use ? The original image The SVG file from inkscape Link to SVG Progress: I tried a tool called InkscapeMap which looks promising and simple, but unfortunately it looks like it didn't work with this particular svn file. Solved! Saving the file as a Plain SVG solved the problem and InkscapeMap worked perfectly. (Btw. saving as an optimized svg caused a parsing error) Update 13.11 Using inkscapeMap 0.6 and Inkscape 0.48 i needed to uncheck relative coordinates in SVG output preferences. Also if you get a C error message, hunt down the polygon with a C in it, and redraw the polygon using the XML editor in inkscape. Update 25.11.2011 I modified the source to improve parsing. http://tovare.com/articles/createhtmlimagemapsusinginkscape/

  Read the article

• Loading the 'pktgen' module on Ubuntu Server

  - by StackedCrooked

  I would like to enable and use the pktgen module on Ubuntu Server. I have enabed the module by adding a line containing 'pktgen' to the /etc/modules file. After rebooting it seems that the module is successfully loaded because the directory /proc/net/pktgen exists. However when trying to run the first sample I get these errors: root@ubuntu:~# bash ./pktgen.conf-1-1 Removing all devices Adding eth4 Setting max_before_softirq 10000 Configuring /proc/net/pktgen/eth4 ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory ./pktgen.conf-1-1: line 9: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory cat: /proc/net/pktgen/eth4: No such file or directory Running... ctrl^C to stop Done It turns out the script simply unable to write a file to the /proc/net/pktgen directory. When I try this manually it fails as well: root@ubuntu:~# cd /proc/net/pktgen/ root@ubuntu:/proc/net/pktgen# touch eth4 touch: cannot touch `eth4': No such file or directory Can anyone help me make it work? I'm using Ubuntu version: 2.6.32-21-server. Fixed I apologize for keeping this post not up to date. I was able to fix it. If I remember well the cause of the error was that eth4 did not exist, or did not have the 'online' status. Anyway, it is fixed now.

  Read the article

• How can I install Satchmo?

  - by Jonathan Hayward

  I am trying to install Satchmo 0.9 on an Ubuntu 9.10 32-bit guest off of the instructions at http://bitbucket.org/chris1610/satchmo/downloads/Satchmo.pdf. I run into difficulties at 2.1.2: pip install -r http://bitbucket.org/chris1610/satchmo/raw/tip/scripts/requirements.txt pip install -e hg+http://bitbucket.org/chris1610/satchmo/@v0.9#egg=satchmo The first command fails because a compile error for how it's trying to build PIL. So I ran an "aptitude install python-imaging", locally copy the first line's requirements.text, and remove the line that's unsuccessfully trying to build PIL. The first line completes without reported error, as does the second. The next step tells me to change directory to the /path/to/new/store, and run: python clonesatchmo.py A little bit of trouble here; I am told that clonesatchmo.py will be in /bin by now, and it isn't there, but I put some Satchmo stuff under /usr/local, create a symlink in /bin, and run: python /bin/clonesatchmo.py This gives: jonathan@ubuntu:~/store$ python /bin/clonesatchmo.py Creating the Satchmo Application Traceback (most recent call last): File "/bin/clonesatchmo.py", line 108, in <module> create_satchmo_site(opts.site_name) File "/bin/clonesatchmo.py", line 47, in create_satchmo_site import satchmo_skeleton ImportError: No module named satchmo_skeleton A find after apparently checking out the repository reveals that there is no file with a name like satchmo*skeleton* on my system. I thought that bash might be prone to take part of the second pip invocation's URL as the beginning of a comment; I tried both: pip install -e hg+http://bitbucket.org/chris1610/satchmo/@v0.9\#egg=satchmo pip install -e hg+http://bitbucket.org/chris1610/satchmo/@v0.9#egg=satchmo Neither way of doing it seems to take care of the import error mentioned above. How can I get a Satchmo installation under Ubuntu, or at least enough of a Satchmo installation that I am able to start with a skeleton of a store and then flesh it out the way I want? Thanks, Jonathan

  Read the article

• 0x0000007b WinXP in VirtualBox with no Admin access on source drive

  - by Ozzah

  I have a physical drive with an installation of WinXP-32 which I have made a clone of using SysInternals disk2vhd. I have no admin rights on this installation. I have tried to boot this VHD in VirtualBox, however it blue screens on 0x0000007b. I have researched this and apparently the cause is that Windows doesn't like the IDE controller changing. I have tried all the available controllers in VirtualBox, but they all produce the same result. There is a Microsoft KB article which describes a method involving loading a .reg file and extracting some sys files from a CAB. This method apparently works well for many people with this problem, however it will not work for me as I don't have admin rights on the WinXP installation. Is there anything I can do in this case? Is there any way of loading the .reg file outside the OS? or perhaps doing a repair using the WinXP CD? Even though I have no admin rights on the source drive installation of Windows, I do obviously have full access to the file system directly on the drive and also in the VHD itself.

  Read the article

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• Linux Kernel Packet Forwarding Performance

  - by Bob Somers

  I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

  Read the article

• How to write files in specific order?

  - by Bernie

  Okay, here's a weird problem -- My wife just bought a 2014 Nissan Altima. So, I took her iTunes library and converted the .m4a files to .mp3, since the car audio system only supports .mp3 and .wma. So far so good. Then I copied the files to a DOS FAT-32 formatted USB thumb drive, and connected the drive to the car's USB port, only to find all of the tracks were out of sequence. All tracks begin with a two digit numeric prefix, i.e., 01, 02, 03, etc. So you would think they would be in order. So I called Nissan Connect support and the rep told me that there is a known problem with reading files in the correct order. He said the files are read in the same order they are written. So, I manually copied a few albums with the tracks in a predetermined order, and sure enough he was correct. So I copied about 6 albums for testing, then changed to the top level directory and did a "find . music.txt". Then I passed this file to rsync like this: rsync -av --files-from=music.txt . ../Marys\ Music\ Sequenced/ The files looked like they were copied in order, but when I listed the files in order of modified time, they were in the same sequence as the original files: ../Marys Music Sequenced/Air Supply/Air Supply Greatest Hits ls -1rt 01 Lost In Love.mp3 04 Every Woman In The World.mp3 03 Chances.mp3 02 All Out Of Love.mp3 06 Here I Am (Just When I Thought I Was Over You).mp3 05 The One That You Love.mp3 08 I Want To Give It All.mp3 07 Sweet Dreams.mp3 11 Young Love.mp3 So the question is, how can I copy files listed in a file named music.txt, and copy them to a destination, and ensure the modification times are in the same sequence as the files are listed?

  Read the article

• How a batch file runs on a remote machine started by PSEXEC

  - by user38780

  I am having an issue running a Batch file on a remote machine suing PSEXEC. The file runs but does not run like it does when run through remote desktop. The batch runs a file which is a 32 bit application, which opens multiple 16bit applications, this should all run under one ntvdm.exe (In one Memory Space). Through remote desktop the batch file runs under the explorer process, and works correctly opening only one ntvdm.exe. Using PSEXEC the batch runs but not under the explorer process, a separate ntvdm.exe is open for each process. I found running the batch from explorer in PSEXEC works, but comes up with a "File Download - Security Warning" eg. psexec.exe" \compname -u username -p passowrd -s -d -i 0 explorer C:\Program.bat I want to be able to run the batch successfully without receiving warnings, it is a local warning and not a network share warning. Possible to recreate warning typing "explorer C:\windows\system32\cmd.exe" in Run I would like to know if anyone knows of a way to get PSEXEC to open the batch file to run as though it was started by explorer. Or a way of removing the local "File Download - Security Warning" Thanks

  Read the article

< Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >