Search Results

Search found 7325 results on 293 pages for 'windows7 32'.

Page 201/293 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >

• Why wifi doesn't work in this case?

  - by xRobot

  I have a brand new notebook where I have installed Windows 7 and Ubuntu 12.04 LTS 64bit in dual boot. In windows 7 wifi works but in Ubuntu not. Could you help me please ? iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off eth0 no wireless extensions. lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 07 serial: b4:b5:1f:1b:9a:56 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:3000(size=256) memory:c2404000-c2404fff memory:c2400000-c2403fff *-network description: Wireless interface product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 84:4b:f4:0a:3a:22 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-31-generic firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:c2500000-c250ffff lspci | grep -i net 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) 02:00.0 Network controller: Ralink corp. Device 539a iwlist scan lo Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Device or resource busy eth0 Interface doesn't support scanning. lsmod Module Size Used by rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224173 1 joydev 17693 0 hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 97362 0 snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device arc4 12529 2 rt2800pci 18715 0 rt2800lib 58925 1 rt2800pci crc_ccitt 12667 1 rt2800lib rt2x00pci 14577 1 rt2800pci rt2x00lib 51144 3 rt2800pci,rt2800lib,rt2x00pci mac80211 506816 3 rt2800lib,rt2x00pci,rt2x00lib soundcore 15091 1 snd mac_hid 13253 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev wmi 19256 1 hp_wmi i915 473240 3 cfg80211 205544 2 rt2x00lib,mac80211 eeprom_93cx6 12725 1 rt2800pci drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 serio_raw 13211 0 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid r8169 62099 0 rfkill list: # rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• eSTEP Newsletter for October 2013 Now Available

  - by Cinzia Mascanzoni

  The October'13 issue of our Newsletter is now available. The issue contains information on the following topics: Oracle Open World Summary Oracle Cloud: Oracle Engineered Systems Oracle Database and Middleware Oracle Applications and Software as a Service Oracle Industries Oracle Partners and the "Internet of Things" JavaOne News MySQL News Corporate News Create Your HR Strategic Vision at Oracle HCM World Oracle Database Protection Redefined A Preview: Oracle Database Backup Logging Recovery Appliance Oracle closed Tekelec acquisition Congratulations to ORACLE TEAM USA! Tech sectionARC M6 Oracle's SPARC M6 Oracle SuperCluster M6-32 - Oracle’s Most Scalable Engineered System Oracle Multitenant on SPARC Servers and Oracle Solaris Oracle Database 12c Enterprise Edition: Plug into the Cloud Oracle In-Memory Database Cache Oracle Virtual Compute Appliance New Benchmark-Results published (Sept. 2013) Video Interview: Elasticity, the Biggest Challenge Facing Data Centers Today Tech blog Announcing New Sun Storage 2500-M2 Drives SPARC Product Line Update ZFS RAID Calculator v6 What ships with ODA X3-2? Tech Article: Oracle Multitenant on SPARC Servers and Oracle Solaris New release of Sun Rack II capacity calculator available Announcing: Oracle Solaris Cluster Product Bulletin, September 2013 Learning & events Planned TechCasts Quarterly Partner Update Live Webcast: Simplify and Accelerate Oracle Database deployment with Oracle VM Templates Join us for OTN's Virtual Developer Day - Harnessing the Power of Oracle WebLogic and Oracle Coherence. Learn from OOW 2013 what is going on in Virtualization How to Implementing Early Arriving Facts in ODI, Part I and Part II: Proof of Concept Overview Multi-Factor Authentication in Oracle WebLogic Using multi-factor authentication to protect web applications deployed on Oracle WebLogic. If Virtualization Is Free, It Can't Be Any Good—Right? Looking beyond System/HW SOA and User Interfaces Overcoming the challenges to developing user interfaces in a service oriented References Vodafone Romania Improves Business Agility and Customer Satisfaction, with 10x Faster Business Intelligence Delivery and 12x Faster Processing Emirates Integrated Telecommunications Captures 47% Market Share in a Competitive Market, Thanks to 24/7 Availability Home Credit and Finance Bank Accelerates Getting New Banking Products to Market Extra A Conversation with Java Champion Johan Vos You can find the Newsletter on our portal under eSTEP News ---> Latest Newsletter. You will need to provide your email address and the pin below to get access. Link to the portal is shown below. URL: http://launch.oracle.com/ PIN: eSTEP_2011 Previous published Newsletters can be found under the Archived Newsletters section and more useful information under the Events, Download and Links tab.

  Read the article

• Open GL polygons not displaying

  - by Darestium

  I have tried to follow nehe's opengl tutorial lesson 2. I use sfml for my window creation. The problem I have is that both the triangle and the quad don't show up on the screen: #include <SFML/System.hpp> #include <SFML/Window.hpp> #include <iostream> void processEvents(sf::Window *app); void processInput(sf::Window *app, const sf::Input &input); void renderCube(sf::Window *app, sf::Clock *clock); void renderGlScene(sf::Window *app); void init(); int main() { sf::Window app(sf::VideoMode(800, 600, 32), "Nehe Lesson 2"); app.UseVerticalSync(false); init(); while (app.IsOpened()) { processEvents(&app); renderGlScene(&app); app.Display(); } return EXIT_SUCCESS; } void init() { glClearDepth(1.f); glClearColor(0.f, 0.f, 0.f, 0.f); // Enable z-buffer and read and write glEnable(GL_DEPTH_TEST); glDepthMask(GL_TRUE); // Setup a perpective projection glMatrixMode(GL_MODELVIEW); glLoadIdentity(); gluPerspective(45.f, 1.f, 1.f, 500.f); glShadeModel(GL_SMOOTH); } void processEvents(sf::Window *app) { sf::Event event; while (app->GetEvent(event)) { if (event.Type == sf::Event::Closed) { app->Close(); } if (event.Type == sf::Event::KeyPressed && event.Key.Code == sf::Key::Escape) { app->Close(); } } } void renderGlScene(sf::Window *app) { app->SetActive(); glClear(GL_COLOR_BUFFER_BIT | GL_DEPTH_BUFFER_BIT); // Clear the screen and the depth buffer glLoadIdentity(); // Reset the view glTranslatef(-1.5f, 0.0f, -6.0f); // Move Left 1.5 units and into the screen 6.0 glBegin(GL_TRIANGLES); glVertex3f( 0.0f, 1.0f, 0.0f); // Top glVertex3f(-1.0,-1.0f, 0.0f); // Bottom Left glVertex3f( 1.0f,-1.0f, 0.0f); // Bottom Right glEnd(); glTranslatef(3.0f, 0.0f, 0.0f); glBegin(GL_QUADS); // Draw a quad glVertex3f(-1.0f, 1.0f, 0.0f); glVertex3f( 1.0f, 1.0f, 0.0f); glVertex3f( 1.0f,-1.0f, 0.0f); glVertex3f(-1.0f,-1.0f, 0.0f); glEnd(); } I would greatly appreciate it if someone could help me resolve my issue.

  Read the article

• What actions does Ubuntu trigger when battery is low?

  - by blueyed

  When the battery is low, the screen gets dimmed after a few seconds already. This appears to be some special power-saving mode, and might be related to the time in org.gnome.settings-daemon.plugins.power.time-low (1200 seconds (20 minutes) the default). While this seems to get triggered by gnome-settings-daemon, I wonder what else Ubuntu does when this happens (e.g. via DBus listeners), or other event listeners that look for a "low battery" state. It seems like something in this regard causes Ubuntu / X / the system to behave more sluggish afterwards (when the laptop is on AC again), and I would like to look into what might be causing this. I could not find anything related via dconf-editor, e.g. in org.gnome.settings-daemon.plugins.power. It appears to get setup via idle_configure in plugins/power/gsd-power-manager.c, but it's probably something more related to something that listens on the DBus interface, which gets notified via e.g.: if (!g_dbus_connection_emit_signal (manager->priv->connection, NULL, GSD_POWER_DBUS_PATH, "org.freedesktop.DBus.Properties", "PropertiesChanged", props_changed, &error)) I could imagine that some "power saving" property gets set, but not unset when AC is available anymore and/or the battery is not low anymore. I have looked at the CPU governor setting (/sys/devices/system/cpu/cpu*/cpufreq/scaling_governor), but it was ondemand. I am using gnome-settings-daemon with awesomeWM on Ubuntu 14.04. gnome-settings-daemon=3.8.6.1-0ubuntu11.1 I've also compared gsd's plugins/power/gsd-power-manager.c with the one from Debian's gnome-settings-daemon-3.12.1, but could not find anything obvious that might have been fixed/changed in this regard. I have managed to trigger the gnome-power-manager's gnome-settings plugin (which dims the screen etc), by patching upower and use it after killing the system's upower daemon. (note that it's probably only energy that is being used by gpm to calculate it by itself). It does not make the system become sluggish.. OTOH I have not heard the speaker's beeping, which might come from the BIOS, which might be involved here, too - or other programs using the kernel's interface on /sys/class/power_supply/BAT0/. --- src/linux/up-device-supply.c.orig 2014-06-07 16:48:32.735920661 +0200 +++ src/linux/up-device-supply.c 2014-06-07 16:48:39.391920525 +0200 @@ -821,6 +821,9 @@ supply->priv->energy_old_first = 0; } + percentage = 3.1f; + time_to_empty = 3*60; + energy = 5; g_object_set (device, "energy", energy, "energy-full", energy_full,

  Read the article

• Toshiba wireless is blocked

  - by zorrillo

  I have the same problem, a 32 bits toshiba nb255, it first had the windows 7 bu next I installed the ubuntu 11.04. The wifi does not turn on. I used the following issues the commands rfkill unblock wlan0, sudo ifconfig wlan0 down; they were not able. by setting up the bios in advanced menu, the wireless communication sw in ON, but it did not work also. neither the utilities toshiba nor utilities of ubuntu (wicd, wifi radar). by using gedit to file group, nothing. by installing madwifi packet, nothing. by exporting the wifi driver from windows to ubuntu, by means of the NDISwrapper packet, neither. I put the current scripts of the ouput of the cli root@zorrillo:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes root@zorrillo:~# sudo lspci | grep Atheros 07:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) root@zorrillo:~# root@zorrillo:~# ifconfig -a eth0 Link encap:Ethernet direcciónHW 88:ae:1d:47:df:e1 ACTIVO DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) Interrupción:43 Dirección base: 0xe000 lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:16436 Métrica:1 Paquetes RX:8 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:8 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:480 (480.0 B) TX bytes:480 (480.0 B) ppp0 Link encap:Protocolo punto a punto Direc. inet:189.203.115.236 P-t-P:192.168.226.1 Másc:255.255.255.255 ACTIVO PUNTO A PUNTO FUNCIONANDO NOARP MULTICAST MTU:1500 Métrica:1 Paquetes RX:6384 errores:30 perdidos:0 overruns:0 frame:0 Paquetes TX:6893 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:3 Bytes RX:5473081 (5.4 MB) TX bytes:974316 (974.3 KB) wlan0 Link encap:Ethernet direcciónHW 00:26:4d:c3:d0:44 DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) note.-it is logical all the counters are cero if the wireless device is down root@zorrillo:/home/zorrillo/Descargas/802BGA# ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill root@zorrillo:/home/zorrillo/Descargas/802BGA# It would seem the wireless switching does not react with whichever ubuntu 11.04 command (I hope to be wrong). The target remains the same, in order of the scripts above. I am worried, I have tried to find any answer for days and nights. Toshiba does not supply drivers or soft support for linux, marketing of course. I only see the device is up by protocols and down phisically, My question is, is it possible to enable or not shutdown physically the device?, because in the toshiba model nb255 the wifi is not set up/down bye means of a physical switch, but by means a combination of Fn + F8 (only for windows 7, no one more), Is there one possibility to configure the hot keys in ubuntu?

  Read the article

• Fans running very fast on MacBook Pro 8.1 ubuntu 12.04

  - by Tomasz Kacprzak

  I installed Ubuntu 12.04 on Macbook Pro 8.1 and one of the first things I noticed was that the fans were starting to spin very fast every few minutes for 10-30 sec and then going back to normal. That was happening even without any processor load, when completely idle. The fans were usually spinning at 4000 RPM and made much noise. The computer was not getting hotter than usual. When running OSX Lion there was no noise at all, fans almost all the time at 2000 RPM. I spent some time on it and found out that Precise uses a deamon to control the temperature, called macfanctld. You can use /etc/macfanctld.conf to set the configuration. I found out that the high fan speed is not due to the fact that the temperature is getting hot, but because there are two sensors which indicate wrong numbers (you can check that using 'sensors' command ): TW0P: +129.0°C TCTD: +256.0°C TCFC: +0.0°C TMBS: +0.0°C or setting the macfanctld log level to 2: Speed: 4992, *AVG: 56.9C, TC0P: 50.2C, TG0P: 51.5C, Sensors: TB0T:34 TB1T:34 TB2T:33 TC0C:58 TC0D:56 TC0E:59 TC0F:60 TC0P:50 TC1C:58 TC2C:58 TC3C:58 TC4C:57 TCFC:0 TCGC:57 TCSA:53 TCTD:256 TG0D:52 TG0P:52 THSP:42 TM0S:64 TMBS:0 TP0P:54 TPCD:60 TW0P:129 Th1H:51 Th2H:48 Tm0P:40 Ts0P:32 Ts0S:43 Moreover, TCTD was randomly jumping from temperatures of 0 to 256, so this may be the reason for unjustified random fan speeds. macfanctld is taking an average of the sensors including the values above, so the actual AVG temp used to control the fans is wrong, usually biased up, hence high RPM and noise. The workaround solution is to use an option in the macfanctld.conf which allows to ignore the malfunctioning sensors: exclude: 13 16 21 24 After reboot the reported temperatures are usually normal and the fans are working at reasonable speeds. I tested the response of the fans to heavy processor load by asking MATLAB to invert 10000x10000 matrix and the AVG temperature jumped to 63deg, and the fan to max 6200 RPM and then got it back to normal temperature. So I think it is safe so far. There is a expired bug about the failing sensor readings: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/955538 which may be good to open again. My question would be: does anyone know what the failing sensors do and if there is any danger in excluding them? Maybe some better solution to this problem?

  Read the article

• Ubuntu 12.4.1 failing in vm both Vbox and Vmware on new HP Envy 4t-1000

  - by Chas

  Brand new to Linux, getting frustrated trying to get an environment up with Ubuntu. My primary goal is to learn Linux and Apache/PHP development. I need to keep my Windows OS as main on my machine for work, so i'm trying to virtualize Ubuntu 12.4.1 without luck (many attempts). I have a new HP Envy 4t-1000 with 16gb ram, and 32 gb ssd caching with 500gb spindle hard drive. Graphics card is an Intel HD 3000 with AMD Radeon 7670M. With installing Ubuntu desktop in VBox, I'm getting this result: https://forums.virtualbox.org/viewtopic.php?f=6&t=51939 With VMware workstation 7 (patched), I complete the install of Ubuntu, it reboots, purple desktop briefly flashes then it drops to command line. I bought a beginning Ubuntu book, and it recommends trying to manually configure graphics if this happens. So I tried doing a safe boot holding shift - I get to the first screen (GRUB) loads fine, and I choose recovery mode. After choosing the recovery mode, I get the recovery mode options, and can arrow down to what the book suggests 'Run in fail safe graphic mode.' Once I select this option, I get a black screen with a large white dialogue box, at the top it says "The system is running in low-graphics mode. Your screen, graphics card, and input device settings could not be detected correctly. You will need to configure these yourself." Then there is an ok button way down at the bottom. When I select 'ok' I get a menu for a few options, book recommended 'reconfigure graphics.' When I try this, I get a menu of two options: 1) "Use generic (default) configuration or 2) use backup. I've tried both options several times, hitting ok just refreshes screen and nothing more. Rebooting at this point just goes back to command line as before. I don't know what to do at this point, I've spent too many hours this weekend trying in both VBox and VMware to get Ubuntu going. Isn't there like a very basic graphic display or something I can use to at least get into the desktop? I explored the GRUB some more, and tried to look at the startup and xserver logs - both are blank. No help there I guess? When I try to choose 'Edit the configuration file, then 'ok' screen just refreshes on same menu options, nothing happens. thx for any advice. I really need to focus on learning Linux, Apache and PHP, so perhaps Ubuntu just won't work on my hardware? Any other suggestions? I will need to virtualize - THANKS for any help/advice.

  Read the article

• Fans running very fast on MacBook Pro 8.1

  - by Tomasz Kacprzak

  I installed Ubuntu 12.04 on Macbook Pro 8.1 and one of the first things I noticed was that the fans were starting to spin very fast every few minutes for 10-30 sec and then going back to normal. That was happening even without any processor load, when completely idle. The fans were usually spinning at 4000 RPM and made much noise. The computer was not getting hotter than usual. When running OSX Lion there was no noise at all, fans almost all the time at 2000 RPM. I spent some time on it and found out that Precise uses a deamon to control the temperature, called macfanctld. You can use /etc/macfanctld.conf to set the configuration. I found out that the high fan speed is not due to the fact that the temperature is getting hot, but because there are two sensors which indicate wrong numbers (you can check that using 'sensors' command ): TW0P: +129.0°C TCTD: +256.0°C TCFC: +0.0°C TMBS: +0.0°C or setting the macfanctld log level to 2: Speed: 4992, *AVG: 56.9C, TC0P: 50.2C, TG0P: 51.5C, Sensors: TB0T:34 TB1T:34 TB2T:33 TC0C:58 TC0D:56 TC0E:59 TC0F:60 TC0P:50 TC1C:58 TC2C:58 TC3C:58 TC4C:57 TCFC:0 TCGC:57 TCSA:53 TCTD:256 TG0D:52 TG0P:52 THSP:42 TM0S:64 TMBS:0 TP0P:54 TPCD:60 TW0P:129 Th1H:51 Th2H:48 Tm0P:40 Ts0P:32 Ts0S:43 Moreover, TCTD was randomly jumping from temperatures of 0 to 256, so this may be the reason for unjustified random fan speeds. macfanctld is taking an average of the sensors including the values above, so the actual AVG temp used to control the fans is wrong, usually biased up, hence high RPM and noise. The workaround solution is to use an option in the macfanctld.conf which allows to ignore the malfunctioning sensors: exclude: 13 16 21 24 After reboot the reported temperatures are usually normal and the fans are working at reasonable speeds. I tested the response of the fans to heavy processor load by asking MATLAB to invert 10000x10000 matrix and the AVG temperature jumped to 63deg, and the fan to max 6200 RPM and then got it back to normal temperature. So I think it is safe so far. There is a expired bug about the failing sensor readings: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/955538 which may be good to open again. My question would be: does anyone know what the failing sensors do and if there is any danger in excluding them? Maybe some better solution to this problem?

  Read the article

• Silverlight and WCF caching

  - by subodhnpushpak

  There are scenarios where Silverlight client calls WCF (or REST) service for data. Now, if the data is cached on the WCF layer, the calls can take considerable resources at the server if NOT cached. Keeping that in mind along with the fact that cache is an cross-cutting aspect, and therefore it should be as easy as possible to put Cache wherever required. The good thing about the solution is that it caches based on the inputs. The input can be basic type of any complex type. If input changes the data is fetched and then cached for further used. If same input is provided again, data id fetched from the cache. The cache logic itself is implemented as PostSharp aspect, and it is as easy as putting an attribute over service call to switch on cache. Notice how clean the code is:        [OperationContract]       [CacheOnArgs(typeof(int))] // based on actual value of cache        public string DoWork(int value)        {            return string.Format("You entered: {0} @ cached time {1}", value, System.DateTime.Now);        } The cache is implemented as POST Sharp as below 1: public override void OnInvocation(MethodInvocationEventArgs eventArgs) 2: { 3: try 4: { 5: object value = new object(); 6: object[] args = eventArgs.GetArgumentArray(); 7: if (args != null || args.Count() > 0) 8: { 9:   10: string key = string.Format("{0}_{1}", eventArgs.Method.Name, XMLUtility<object>.GetDataContractXml(args[0], null));// Compute the cache key (details omitted). 11:   12: 13: value = GetFromCache(key); 14: if (value == null) 15: { 16: eventArgs.Proceed(); 17: value = XMLUtility<object>.GetDataContractXml(eventArgs.ReturnValue, null); 18: value = eventArgs.ReturnValue; 19: AddToCache(key, value); 20: return; 21: } 22:   23:   24: Log(string.Format("Data returned from Cache {0}",value)); 25: eventArgs.ReturnValue = value; 26: } 27: } 28: catch (Exception ex) 29: { 30: //ApplicationLogger.LogException(ex.Message, Source.UtilityService); 31: } 32: } 33:   34: private object GetFromCache(string inputKey) { if (ServerConfig.CachingEnabled) { return WCFCache.Current[inputKey]; } return null; }private void AddToCache(string inputKey,object outputValue) 35: { 36: if (ServerConfig.CachingEnabled) 37: { 38: if (WCFCache.Current.CachedItemsNumber < ServerConfig.NumberOfCachedItems) 39: { 40: if (ServerConfig.SlidingExpirationTime <= 0 || ServerConfig.SlidingExpirationTime == int.MaxValue) 41: { 42: WCFCache.Current[inputKey] = outputValue; 43: } 44: else 45: { 46: WCFCache.Current.Insert(inputKey, outputValue, new TimeSpan(0, 0, ServerConfig.SlidingExpirationTime), true); 47:   48: // _bw.DoWork += bw_DoWork; 49: //string arg = string.Format("{0}|{1}", inputKey,outputValue); 50: //_bw.RunWorkerAsync(inputKey ); 51: } 52: } 53: } 54: }     The cache class can be extended to support Velocity / memcahe / Nache. the attribute can be used over REST services as well. Hope the above helps. Here is the code base for the same.   Please do provide your inputs / comments.

  Read the article

• Weird Ubuntu Desktop Boot Partition On External Hard Drive

  - by Magnitus

  I have a Thinkpad with Windows 7. Last time I installed an Ubuntu/Windows dual boot, Windows was never same after and regularly got corrupted so this time, I installed Ubuntu on a separate external hard drive. I took a 500 GB external hard drive and used Windows to shrink the partition on it to 400 GB, freeing 100 GB to install Ubuntu. Then I modified the booting priority of my computer to boot from the external hard drive if present. Then, I installed Ubuntu desktop on the external hard drive using a DVD, picked the most simplistic partitioning scheme I could get away with (didn't go auto as it didn't include the external hard drive as a choice) and voilà. Fast forward some time and I'm trying to refresh my understanding of Linux partitions to install a bunch of servers, so I'm looking at the current partitioning scheme on my external hard drive and find the boot partition puzzling... sda is my integrated hard drive with Windows 7. sdb is my Ubuntu desktop external hard drive. Running parted on sdb, I get this: (parted) print Model: WD My Passport 0740 (scsi) Disk /dev/sdb: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 393GB 393GB primary ntfs boot 2 393GB 500GB 107GB extended 5 393GB 425GB 32.8GB logical linux-swap(v1) 6 425GB 500GB 74.6GB logical ext4 At this point, I'm wondering why the ntfs partition is flagged as "boot" and not my ext4 partition which is the partition that contains / (and by extension, /boot since it's not on its own separate partition). Looking at mtab only confirms what I already know: eric@eric-ThinkPad-W530:~$ sudo cat /etc/mtab /dev/sdb6 / ext4 rw,errors=remount-ro 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 none /sys/fs/cgroup tmpfs rw 0 0 none /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 udev /dev devtmpfs rw,mode=0755 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 tmpfs /run tmpfs rw,noexec,nosuid,size=10%,mode=0755 0 0 none /run/lock tmpfs rw,noexec,nosuid,nodev,size=5242880 0 0 none /run/shm tmpfs rw,nosuid,nodev 0 0 none /run/user tmpfs rw,noexec,nosuid,nodev,size=104857600,mode=0755 0 0 none /sys/fs/pstore pstore rw 0 0 systemd /sys/fs/cgroup/systemd cgroup rw,noexec,nosuid,nodev,none,name=systemd 0 0 gvfsd-fuse /run/user/1000/gvfs fuse.gvfsd-fuse rw,nosuid,nodev,user=eric 0 0 /dev/sdb1 /media/eric/My\040Passport fuseblk rw,nosuid,nodev,allow_other,default_permissions,blksize=4096 0 0 My lack of understanding concerning this is not vital to anything (this is only my development desktop partition), but somehow annoys me. Any insight that could shed some light on this would be welcome.

  Read the article

• openGL textures in bitmap mode

  - by evenex_code

  For reasons detailed here I need to texture a quad using a bitmap (as in, 1 bit per pixel, not an 8-bit pixmap). Right now I have a bitmap stored in an on-device buffer, and am mounting it like so: glBindBuffer(GL_PIXEL_UNPACK_BUFFER, BFR.G[(T+1)%2]); glTexImage2D(GL_TEXTURE_2D, 0, GL_RGB, W, H, 0, GL_COLOR_INDEX, GL_BITMAP, 0); The OpenGL spec has this to say about glTexImage2D: "If type is GL_BITMAP, the data is considered as a string of unsigned bytes (and format must be GL_COLOR_INDEX). Each data byte is treated as eight 1-bit elements..." Judging by the spec, each bit in my buffer should correspond to a single pixel. However, the following experiments show that, for whatever reason, it doesn't work as advertised: 1) When I build my texture, I write to the buffer in 32-bit chunks. From the wording of the spec, it is reasonable to assume that writing 0x00000001 for each value would result in a texture with 1-px-wide vertical bars with 31-wide spaces between them. However, it appears blank. 2) Next, I write with 0x000000FF. By my apparently flawed understanding of the bitmap mode, I would expect that this should produce 8-wide bars with 24-wide spaces between them. Instead, it produces a white 1-px-wide bar. 3) 0x55555555 = 1010101010101010101010101010101, therefore writing this value ought to create 1-wide vertical stripes with 1 pixel spacing. However, it creates a solid gray color. 4) Using my original 8-bit pixmap in GL_BITMAP mode produces the correct animation. I have reached the conclusion that, even in GL_BITMAP mode, the texturer is still interpreting 8-bits as 1 element, despite what the spec seems to suggest. The fact that I can generate a gray color (while I was expecting that I was working in two-tone), as well as the fact that my original 8-bit pixmap generates the correct picture, support this conclusion. Questions: 1) Am I missing some kind of prerequisite call (perhaps for setting a stride length or pack alignment or something) that will signal to the texturer to treat each byte as 8-elements, as it suggests in the spec? 2) Or does it simply not work because modern hardware does not support it? (I have read that GL_BITMAP mode was deprecated in 3.3, I am however forcing a 3.0 context.) 3) Am I better off unpacking the bitmap into a pixmap using a shader? This is a far more roundabout solution than I was hoping for but I suppose there is no such thing as a free lunch.

  Read the article

• Basic Android game loop having issues

  - by WillDaBeast509

  I've set up a very basic game loop that should draw a circle, run 100 times, then draw another. I also have a text field that should display how many times the loop has ran. However, the screen seems to not update. It displays a different value for the tick count (different each time the app is ran) and simply stays there. After exiting the app, I get an error saying "Unfortunately, MyApp has stopped." Here is the relevant code: DrawView public class DrawView extends SurfaceView implements SurfaceHolder.Callback { Paint p = new Paint(); MainThread thread; private int y=0; public DrawView(Context c) { super(c); thread = new MainThread(this, getHolder()); thread.running = true; getHolder().addCallback(this); setFocusable(true); } public void draw(Canvas c) { if(c==null) return; //super.onDraw(c); c.drawColor(Color.WHITE); p.setColor(Color.RED); p.setTextSize(32); p.setTypeface(Typeface.SANS_SERIF); c.drawCircle(getWidth()/2-100,getHeight()/2, 50, p); c.drawText("y = " + y, 50, 50, p); if(y>=100) { Log.i("DRAW", "drawing circle"); c.drawCircle(getWidth()/2+100,getHeight()/2, 50, p); } else y++; Log.i("INFO", "y = " + y); } @Override public boolean onTouchEvent(MotionEvent event) { return true; } public void onDraw(Canvas c){} public void surfaceCreated(SurfaceHolder p1) { thread.start(); } public void surfaceChanged(SurfaceHolder p1, int p2, int p3, int p4) { // TODO: Implement this method } public void surfaceDestroyed(SurfaceHolder p1) { thread.running = false; boolean retry = true; while (retry) { try { thread.join(); retry = false; } catch (InterruptedException e) { Log.i("EX", "cathing exception"); } } } } MainThread public class MainThread extends Thread { private DrawView page; private SurfaceHolder holder; public boolean running; public MainThread(DrawView p, SurfaceHolder h) { super(); page = p; holder = h; } @Override public void run() { while(running) { Canvas c = holder.lockCanvas(); page.draw(c); holder.unlockCanvasAndPost(c); } } } Here is an example log outupt: http://pastebin.com/tM9dUPuk It counts the number of ticks correctly and should draw the second circle, but the screen looks like its not updating. After closing the app, the log continues to run and keep outputting "y = 100 drawing circle" until it crashes and shows the error report. What is going on and how can I fix these two problems?

  Read the article

• Where i set touch effect when a spawn Srite are comming on the screen?

  - by shihab_returns

  I just create a scene where create a spawn spirit that comes from above screen height in Landscape mode. Now i want to remove spirits when i touch on it. I tried but seems the code not works and crashed also after a while. here is my code: /** TimerHandler for collision detection and cleaning up */ IUpdateHandler detect = new IUpdateHandler() { @Override public void reset() { } @Override public void onUpdate(float pSecondsElapsed) { Iterator<AnimatedSprite> targets = targetLL.iterator(); AnimatedSprite _target; while (targets.hasNext()) { _target = targets.next(); if (_target.getY() >= cameraHeight) { // removeSprite(_target, targets); tPool.recyclePoolItem(_target); targets.remove(); Log.d("ok", "---------Looop Inside-----"); // fail(); break; } } targetLL.addAll(TargetsToBeAdded); TargetsToBeAdded.clear(); } }; /** adds a target at a random location and let it move along the y-axis */ public void addTarget() { Random rand = new Random(); int minX = mTargetTextureRegion.getWidth(); int maxX = (int) (mCamera.getWidth() - mTargetTextureRegion.getWidth()); int rangeX = maxX - minX; Log.d("----point----", "minX:" + minX + "maxX:" + maxX + "rangeX:" + rangeX); int rX = rand.nextInt(rangeX) + minX; int rY = (int) mCamera.getHeight() + mTargetTextureRegion.getHeight(); Log.d("---Random x----", "Random x" + rX + "Random y" + rY); target = tPool.obtainPoolItem(); target.setPosition(rX, rY); target.animate(100); mMainScene.attachChild(target, 1); mMainScene.registerTouchArea(target); int minDuration = 2; int maxDuration = 32; int rangeDuration = maxDuration - minDuration; int actualDuration = rand.nextInt(rangeDuration) + minDuration; // MoveXModifier mod = new MoveXModifier(actualDuration, target.getX(), // -target.getWidth()); MoveYModifier mody = new MoveYModifier(actualDuration, -target.getHeight(), cameraHeight + 10); target.registerEntityModifier(mody.deepCopy()); TargetsToBeAdded.add(target); } @Override public boolean onAreaTouched(final TouchEvent pSceneTouchEvent, final ITouchArea pTouchArea, final float pTouchAreaLocalX, final float pTouchAreaLocalY) { if (pTouchArea == target) { Toast.makeText(getApplicationContext(), "Yoooooooo", Toast.LENGTH_LONG).show(); } return true; } ** My question is where i implements IOnAreaTouchListener in My code. ? ** Thanks in Advance.

  Read the article

• SQL Server Memory Manager Changes in Denali

  - by SQLOS Team

  The next version of SQL Server will contain significant changes to the memory manager component.  The memory manager component has been rewritten for Denali.  In the previous versions of SQL Server there were two distinct memory managers.  There was one memory manager which handled allocation sizes of 8k or less and another for greater than 8k.  For Denali there will be one memory manager for all allocation sizes.   The majority of the changes will be transparent to the end user.  However, some changes will be visible to the user.  These are listed below: ·         The ‘max server memory’ configuration option has new lower limits.  Specifically, 32-bit versions of SQL Server will have a lower limit of 64 MB.  The 64-bit versions will have a lower limit of 128 MB. ·         All memory allocations by SQL Server components will observe the ‘max server memory’ configuration option.  In previous SQL versions only the 8k allocations were limited the ‘max server memory’ configuration option.  Allocations larger than 8k weren’t constrained. ·         DMVs which refer to memory manager internals have been modified.  This includes adding or removing columns and changing column names. ·         The memory manager configuration messages in the error log have minor changes. ·         DBCC memorystatus output has been changed. ·         Address Windowing Extensions (AWE) has been deprecated.   In the next blog post I will discuss the changes to the memory manager DMVs in greater detail.  In future blog posts I will discuss the other changes in greater detail.  

  Read the article

• Generate GUID from any string using C#

  - by Haitham Khedre

  Some times you need to generate GUID from a string which is not valid for GUID constructor . so what we will do is to get a valid input from string that the GUID constructor will accept it. It is recommended to be sure that the string that you will generate a GUID from it some how unique. The Idea is simple is to convert the string to 16 byte Array which the GUID constructor will accept it. The code will talk : using System; using System.Text; namespace StringToGUID { class Program { static void Main(string[] args) { int tokenLength = 32; int guidByteSize = 16; string token = "BSNAItOawkSl07t77RKnMjYwYyG4bCt0g8DVDBv5m0"; byte[] b = new UTF8Encoding().GetBytes(token.Substring(token.Length - tokenLength, tokenLength).ToCharArray(), 0, guidByteSize); Guid g = new Guid(b); Console.WriteLine(g.ToString()); token = "BSNePf57YwhzeE9QfOyepPfIPao4UD5UohG_fI-#eda7d"; b = new UTF8Encoding().GetBytes(token.Substring(token.Length - tokenLength, tokenLength).ToCharArray(), 0, guidByteSize); g = new Guid(b); Console.WriteLine(g.ToString()); Console.Read(); } } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   And The output: 37306c53-3774-5237-4b6e-4d6a59775979 66513945-794f-7065-5066-4950616f3455

  Read the article

• LWJGL: Camera distance from image plane?

  - by Rogem

  Let me paste some code before I ask the question... public static void createWindow(int[] args) { try { Display.setFullscreen(false); DisplayMode d[] = Display.getAvailableDisplayModes(); for (int i = 0; i < d.length; i++) { if (d[i].getWidth() == args[0] && d[i].getHeight() == args[1] && d[i].getBitsPerPixel() == 32) { displayMode = d[i]; break; } } Display.setDisplayMode(displayMode); Display.create(); } catch (Exception e) { e.printStackTrace(); System.exit(0); } } public static void initGL() { GL11.glEnable(GL11.GL_TEXTURE_2D); GL11.glShadeModel(GL11.GL_SMOOTH); GL11.glClearColor(0.0f, 0.0f, 0.0f, 0.0f); GL11.glClearDepth(1.0); GL11.glEnable(GL11.GL_DEPTH_TEST); GL11.glDepthFunc(GL11.GL_LEQUAL); GL11.glMatrixMode(GL11.GL_PROJECTION); GL11.glLoadIdentity(); GLU.gluPerspective(45.0f, (float) displayMode.getWidth() / (float) displayMode.getHeight(), 0.1f, 100.0f); GL11.glMatrixMode(GL11.GL_MODELVIEW); GL11.glHint(GL11.GL_PERSPECTIVE_CORRECTION_HINT, GL11.GL_NICEST); } So, with the camera and screen setup out of the way, I can now ask the actual question: How do I know what the camera distance is from the image plane? I also would like to know what the angle between the image plane's center normal and a line drawn from the middle of one of the edges to the camera position is. This will be used to consequently draw a vector from the camera's position through the player's click-coordinates to determine the world coordinates they clicked (or could've clicked). Also, when I set the camera coordinates, do I set the coordinates of the camera or do I set the coordinates of the image plane? Thank you for your help. EDIT: So, I managed to solve how to calculate the distance of the camera... Here's the relevant code... private static float getScreenFOV(int dim) { if (dim == 0) { float dist = (float) Math.tan((Math.PI / 2 - Math.toRadians(FOV_Y))/2) * 0.5f; float FOV_X = 2 * (float) Math.atan(getScreenRatio() * 0.5f / dist); return FOV_X; } else if (dim == 1) { return FOV_Y; } return 0; } FOV_Y is the Field of View that one defines in gluPerspective (float fovy in javadoc). This seems to be (and would logically be) for the height of the screen. Now I just need to figure out how to calculate that vector.

  Read the article

• ??????????

  - by Allen Gao

  ???????RAC??????????????????10gR2?11gR1.??????????????CRS???????1.ocssd : ???????????(Node Monitoring)????(Group Management),??CRS????????????????????????,????????????(network heartbeat)?????(disk heartbeat)???,?????????????????????,????????????,??????????????????,?????node kill escalation(???11gR1????????),??????????????????????????(reboot time,???3?)????????:ocssd.bin??????????????????????????,??????????????????????????????,misscount(???30?,??????????????600?),????????????,???????????????????,?????????????2???,??????,??????????????,?????????????????????:ocssd.bin?????????????(Voting File)??????????,?????????????????????????????,disk timeou(???200?),?????????????????????,CRS???[N/2]+1????????,??N??????,??????2.oclsomon:????????ocssd????,????ocssd.bin??????,???????3.oprocd:??????Linux?Unix??,????????????????????????????????,?????????:????????????init.cssd?????????????????????????1.??????2.<crs???>/log/<????>/cssd/ocssd.log3.oprocd.log(/etc/oracle/oprocd/*.log.* ? /var/opt/oracle/oprocd/*.log.*)4.<crs???>/log/<????>/cssd/oclsomon/oclsomon.log5. Oracle OSWatcher ????????????????????1.?ocssd???????????ocssd.log???????,????????????????????????????????,???????,OSW??(traceroute???),???????(cluster interconnect)??????,?????????[ CSSD]2012-03-02 23:56:18.749 [3086] >WARNING: clssnmPollingThread: node <node_name> at 50% heartbeat fatal, eviction in 14.494 seconds[ CSSD]2012-03-02 23:56:25.749 [3086] >WARNING: clssnmPollingThread: node <node_name> at 75% heartbeat fatal, eviction in 7.494 seconds[ CSSD]2012-03-02 23:56:32.749 [3086] >WARNING: clssnmPollingThread: node <node_name>at 90% heartbeat fatal, eviction in 0.494 seconds[CSSD]2012-03-02 23:56:33.243 [3086] >TRACE:   clssnmPollingThread: Eviction started for node <node_name>, flags 0x040d, state 3, wt4c 0[CSSD]2012-03-02 23:56:33.243 [3086] >TRACE:   clssnmDiscHelper: <node_name>, node(4) connection failed, con (1128a5530), probe(0)[CSSD]2012-03-02 23:56:33.243 [3086] >TRACE:   clssnmDiscHelper: node 4 clean up, con (1128a5530), init state 5, cur state 5[CSSD]2012-03-02 23:56:33.243 [3600] >TRACE:   clssnmDoSyncUpdate: Initiating sync 196446491[CSSD]2012-03-02 23:56:33.243 [3600] >TRACE:   clssnmDoSyncUpdate: diskTimeout set to (27000)ms??:???????ocssd.log?????????????????????,?????????????????????ocssd.log???????,??????????????????????????????,OSWatcher??(iostat???),???i/o????????,?????????2010-08-13 18:34:37.423: [    CSSD][150477728]clssnmvDiskOpen: Opening /dev/sdb82010-08-13 18:34:37.423: [    CLSF][150477728]Opened hdl:0xf4336530 for dev:/dev/sdb8:2010-08-13 18:34:37.429: [   SKGFD][150477728]ERROR: -9(Error 27072, OS Error (Linux Error: 5: Input/output errorAdditional information: 4Additional information: 720913Additional information: -1))2010-08-13 18:34:37.429: [    CSSD][150477728](:CSSNM00060: )clssnmvReadBlocks: read failed at offset 17 of /dev/sdb82010-08-13 18:34:38.205: [    CSSD][4110736288](:CSSNM00058: )clssnmvDiskCheck: No I/O completions for 200880 ms for voting file /dev/sdb8)2010-08-13 18:34:38.206: [    CSSD][4110736288](:CSSNM00018: )clssnmvDiskCheck: Aborting, 0 of 1 configured voting disks available, need 12010-08-13 18:34:38.206: [    CSSD][4110736288]###################################2010-08-13 18:34:38.206: [    CSSD][4110736288]clssscExit: CSSD aborting from thread clssnmvDiskPingMonitorThread 2010-08-13 18:34:38.206: [    CSSD][4110736288]###################################2. ?oclsomon???????????oclsomon.log ?????,??????????ocssd????,??ocssd??????(RT)???,?????????????(?cpu)??,?????????????,OSW??(vmstat,top???),?????????3.?oprocd???????????oprocd?????????,?????????oprocd????? Dec 21 16:15:30.369857 | LASTGASP | AlarmHandler:  timeout(2312 msec) exceeds interval(1000 msec)+margin(500 msec).   Rebooting NOW.??oprocd?????????????????????,?????ntp(?????????),??diagwait=13 ????????,??,?????????????,??????CRS,???????????????,??????????????oprocd????,??,?????OSWatcher??(vmstat,top???),??????????????????????????????,????????????????? ???????,??????MOS ???Note 265769.1 :Troubleshooting 10g and 11.1 Clusterware RebootsNote 1050693.1 :Troubleshooting 11.2 Clusterware Node Evictions (Reboots)

  Read the article

• Problems trying to use Visual Studio 2010 and AJAX extensions

  - by Adrian

  Why can I not add ScriptManager control or UpdatePanel to a page in Visual Studio 2010? The drag( or double click) just fails - it seems like there is an incompatibility somewhere? UPDATE: This is 'default' install of 2010 Ultimate on Windows7, create a web application, cannot drag ScriptManager or UpdatePanel to the designer. Typing the declarations works. The cursor changes to the [+] icon when you drag it to the right place but nothing appears to happens on 'drop', briefly the documents name has * appended, this quickly changes back to normal, either is saves or does an undo. I'm assuming something is going wrong so it undos...but what is going wrong?

  Read the article

• architecture mismatch between the Driver and Application?

  - by shane87

  I am using JDBC to connect to my microsoft access database. I get the following exception when I try to connect to the database: java.sql.SQLException: [Microsoft][ODBC Driver Manager] The specified DSN contains an architecture mismatch between the Driver and Application I am using 64bit windows7, and I am using eclipse which is also a 64bit version My database is a microsoft access database and it seems that the driver is a 32bit driver which is causing the problem. I read somewhere that microsoft has not released a 64bit driver for microsoft access! Any help on how to solve this problem would be greatly appreciated.

  Read the article

• Errno::EACCES: Permission denied - ./tmp/rspec_guard_result

  - by Evgeniy Gatsalov

  Trying settup rspec-guard-spork for learning app from http://ruby.railstutorial.org/ Using Ruby 2.0, Rails 4.0 on Windows7 ( I know :( ) When starting guard, get: 23:02:51 - ERROR - Guard::RSpec failed to achieve its <run_on_modifications>, exception was: > [#] Errno::EACCES: Permission denied - ./tmp/rspec_guard_result ... All gemfile, guardfile etc are edited according tutorial. Except 1) deleting win32console gem from gemfile because it turned console-out into a crap and raised an error. Permissions for a file is "F"(ull) for all cattegories: D:\WebDevelop\sample_appcacls tmp\rspec_guard_result D:\WebDevelop\sample_app\tmp\rspec_guard_result BUILTIN\Users:(ID)F NT AUTHORITY\Authenticated:(ID)F BUILTIN\Administrators:(ID)F NT AUTHORITY\system:(ID)F What additional info should I provide here?

  Read the article

• Mongo connect problem using asp.net

  - by Amr ElGarhy

  I wrote these lines in My Application start event: var mongo = new Mongo(); mongo.Connect(); var blog = mongo.GetDatabase("Blog"); mongo.Disconnect(); but on this line: mongo.Connect(); it gave me this error: No connection could be made because the target machine actively refused it 127.0.0.1:27017 I am a beginner using Mongodb and i am just try to make sample code to see it's power. So i have no idea how to solve this problem. I am using VS2008 with MongoDB.Driver on Windows7.

  Read the article

• Path for Delphi libraries

  - by Wouter van Nifterick

  Where do you guys store 3rd party (and your own) components? Do you keep separate copies per Delphi version? For years I've been using c:\program files\borland\delphi7\lib\, even for Delphi 2006, 2007, 2009 and 2010, like this: c:\program files\borland\delphi7\lib\AggPas\ c:\program files\borland\delphi7\lib\DeHL\ c:\program files\borland\delphi7\lib\DevExpress\ c:\program files\borland\delphi7\lib\FastCode\ c:\program files\borland\delphi7\lib\FastMM\ c:\program files\borland\delphi7\lib\Fundamentals\ c:\program files\borland\delphi7\lib\Graphics32\ c:\program files\borland\delphi7\lib\JCL\ c:\program files\borland\delphi7\lib\JVCL\ c:\program files\borland\delphi7\lib\OmniThread\ c:\program files\borland\delphi7\lib\Raize\ c:\program files\borland\delphi7\lib\TeeChartPro\ c:\program files\borland\delphi7\lib\TurboPower\ c:\program files\borland\delphi7\lib\VirtualTreeView\ c:\program files\borland\delphi7\lib\Zeos\ However, nowadays I don't even use Delphi7 anymore (what can it do that 2010 can't?), so this path doesn't make much sense anymore. I'm about to install windows7 on my home machine, so I'm thinking on something like this: c:\src\DelphiLib\ Any better ideas?

  Read the article

• Can I modify package.xml file in SQL bootstrapper to install a named SQL server instance

  - by jonmiddleton

  I want to use the SqlExpress2008 Bootstrapper for a new installation on Windows7, I do not want to use the default SQLEXPRESS Instance. I have attempted to edit the package.xml file located in: C:\Program Files\Microsoft SDKs\Windows\v7.0A\Bootstrapper\Packages\SqlExpress2008\en\package.xml and updated the command argument instancename=CUSTOMINSTANCE But unfortunately it still creates the default SQLEXPRESS not CUSTOMINSTANCE The wix tag is as follows: <sql:SqlDatabase Id="SqlDatabaseCore" ConfirmOverwrite="yes" ContinueOnError="no" CreateOnInstall="yes" CreateOnReinstall="no" CreateOnUninstall="no" Database="MyDatabase" DropOnInstall="no" DropOnReinstall="no" DropOnUninstall="no" Instance="[SQLINSTANCE]" Server="[SQLSERVER]"> <sql:SqlFileSpec Id="SqlFileSpecCore" Filename="[CommonAppDataFolder]MyCompany\Database\MyDatabase.mdf" Name="MyDatabase" /> <sql:SqlLogFileSpec Id="SqlLogFileSpecCore" Filename="[CommonAppDataFolder]MyCompany\Database\MyDatabase.ldf" Name="MyDatabaseLog" /> Is this the standard way to accomplish this?

  Read the article

• Invoking MSYS bash from Windows cmd

  - by daevius

  I'm using GCC on Windows7 (using the TDM's build). I installed MSYS to be able to execute make and compile using makefiles. However, it is tedious to every time start up the MSYS bash shell, navigate to the directory of the project and run make. What I want is to automate this process. I prefer to have a batch file in Windows, or something similar, from which I then invoke the MSYS bash. It should navigate to the directory the batch file resides in and call "make". Is this possible? Can I send commands to MSYS bash from cmd (like navigation / invoking make)? Or can I let the MSYS bash run a "bash script", which sets the commands to be executed much like batch scripts? Thank you. PS: this is something similar as this question: http://stackoverflow.com/questions/2546757/executing-msys-from-cmd-exe-with-arguments

  Read the article

• Apache not loading Xdebug, but does when started from the Command Line

  - by JamesD

  I know that this sounds odd, but believe me, it's what is happening. Here are my system settings: Windows7 Apache 2.2 PHP 5.2.12 Xdebug 2.0.5 I have XDebug configured in my PHP.ini file. When I run php -m, I do in fact see that Xdebug is loaded. Now, if I start Apache AS A SERVICE (or by the Apache Monitor), and run phpinfo(), it is NOT showing Xdebug as being loaded. However, (now here's the crazy part), if I go to my Apache bin directory, and simply run httpd.exe, and then go and look at phpinfo(), Xdebug now shows as being loaded! Also, comparing some phpinfo() when started via service or by command line, it looks like the php.ini file is the same for either case. Everything looks the same except for the Xdebug being loaded part. Please, if you have any ideas it would be greatly appreciated.

  Read the article

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >