Search Results

Search found 981 results on 40 pages for '015 lo'.

Page 21/40 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

• CentOS 6.2 Bridge Setup for KVM

  - by Gaia

  I'm trying to set up bridged networking with KVM on CentOS 6.2 to no avail. There are plenty of docs and tutorials about it, but they all seem to conflict or don't provide info specific enough to my situation. I just don't get it. I access the host via public IP "xxx.xxx.128.58". All other available IPs (/29) should be bridged and made available to the only KVM guest (running a public facing LAMP stack) that will be setup on this machine. The amazingly unhelpful NOC people assigned the extra IPs to eth1. Is this correct? Should br0 bridge to eth0 or eth1? How do I set this up? Here is the relevant info: eth0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BC inet6 addr: fe80::225:90ff:fe68:febc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:763 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:550811 (537.9 KiB) TX bytes:648 (648.0 b) Memory:fb980000-fba00000 eth1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.58 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 inet6 addr: fe80::225:90ff:fe68:febd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1806 errors:0 dropped:0 overruns:0 frame:0 TX packets:1505 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:133166 (130.0 KiB) TX bytes:106070 (103.5 KiB) Memory:fb900000-fb980000 eth1:0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.59 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.60 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:2 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.61 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:3 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.62 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) virbr0 Link encap:Ethernet HWaddr 52:54:00:62:55:68 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=XXXX.domain.com > brctl show bridge name bridge id STP enabled interfaces br0 8000.00259068febc no eth0 virbr0 8000.525400625568 yes virbr0-nic > ls -fl | grep ifcfg -rw-r--r-- 1 root root 198 Jun 7 10:58 ifcfg-eth0 -rw-r--r--. 1 root root 254 Oct 7 2011 ifcfg-lo -rw-r--r-- 1 root root 77 Jun 6 18:51 ifcfg-eth1-range0 -rw-r--r-- 1 root root 168 Jun 6 18:50 ifcfg-eth1 > cat ifcfg-eth0 DEVICE="eth0" BOOTPROTO="static" BRIDGE="br0" HWADDR="00:25:90:68:FE:BC" IPV6INIT="yes" MTU="1500" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" IPADDR="yyy.yyy.216.131" NETMASK="255.255.255.128" > cat ifcfg-eth1 DEVICE="eth1" HWADDR="00:25:90:68:FE:BD" NM_CONTROLLED="yes" ONBOOT="yes" BOOTPROTO="static" IPADDR="xxx.xxx.128.58" NETMASK="255.255.255.248" GATEWAY="xxx.xxx.128.57" > cat ifcfg-eth1-range0 IPADDR_START="xxx.xxx.128.59" IPADDR_END="xxx.xxx.128.62" CLONENUM_START="0" Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xxx.xxx.128.56 * 255.255.255.248 U 0 0 0 eth1 192.168.122.0 * 255.255.255.0 U 0 0 0 virbr0 link-local * 255.255.0.0 U 1003 0 0 eth1 default xxx.xxx.128.57 0.0.0.0 UG 0 0 0 eth1

  Read the article

• hostapd running on Ubuntu Server 13.04 only allows single station to connect when using wpa

  - by user450688

  Problem Only a single station can connect to hostapd at a time. Any single station can connect (W8, OSX, iOS, Nexus) but when two or more hosts are connected at the same time the first client loses its connectivity. However there are no connectivity issues when WPA is not used. Setup Linux (Ubuntu server 13.04) wireless router (with separate networks for wired WAN, wired LAN, and Wireless LAN. iptables-save output: *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.0.0/24 -o p4p1 -j MASQUERADE -A POSTROUTING -s 10.0.1.0/24 -o p4p1 -j MASQUERADE COMMIT *mangle :PREROUTING ACCEPT [13:916] :INPUT ACCEPT [9:708] :FORWARD ACCEPT [4:208] :OUTPUT ACCEPT [9:3492] :POSTROUTING ACCEPT [13:3700] COMMIT *filter :INPUT DROP [0:0] :FORWARD DROP [0:0] :OUTPUT ACCEPT [9:3492] -A INPUT -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i p4p1 -p tcp -m tcp --dport 22 -m state --state NEW -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i wlan0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A FORWARD -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -i eth0 -j ACCEPT -A FORWARD -i wlan0 -j ACCEPT -A FORWARD -i lo -j ACCEPT COMMIT /etc/hostapd/hostapd.conf #Wireless Interface interface=wlan0 driver=nl80211 ssid=<removed> hw_mode=g channel=6 max_num_sta=15 auth_algs=3 ieee80211n=1 wmm_enabled=1 wme_enabled=1 #Configure Hardware Capabilities of Interface ht_capab=[HT40+][SMPS-STATIC][GF][SHORT-GI-20][SHORT-GI-40][RX-STBC12] #Accept all MAC address macaddr_acl=0 #Shared Key Authentication wpa=1 wpa_passphrase=<removed> wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ###IPad Connectivevity Repair ieee8021x=0 eap_server=0 Wireless Card #lshw output product: RT2790 Wireless 802.11n 1T/2R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 00 serial: <removed> width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=rt2800pci driverversion=3.8.0-25-generic firmware=0.34 ip=10.0.1.254 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn #iw list output Band 1: Capabilities: 0x272 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (27.0 dBm) * 2417 MHz [2] (27.0 dBm) * 2422 MHz [3] (27.0 dBm) * 2427 MHz [4] (27.0 dBm) * 2432 MHz [5] (27.0 dBm) * 2437 MHz [6] (27.0 dBm) * 2442 MHz [7] (27.0 dBm) * 2447 MHz [8] (27.0 dBm) * 2452 MHz [9] (27.0 dBm) * 2457 MHz [10] (27.0 dBm) * 2462 MHz [11] (27.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ AP } <= 8, total <= 8, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * set_tx_bitrate_mask * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (84) * Unknown command (87) * Unknown command (85) * Unknown command (89) * Unknown command (92) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * Unknown mode (10): 0x40 0xd0 Device supports RSN-IBSS. HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS.

  Read the article

• vlans on openvz, centos 6

  - by arheops

  i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

  Read the article

• iptables - quick safety eval & limit max conns over time

  - by Peter Hanneman

  Working on locking down a *nix server box with some fancy iptable(v1.4.4) rules. I'm approaching the matter with a "paranoid, everyone's out to get me" style, not necessarily because I expect the box to be a hacker magnet but rather just for the sake of learning iptables and *nix security more throughly. Everything is well commented - so if anyone sees something I missed please let me know! The *nat table's "--to-ports" point to the only ports with actively listening services. (aside from pings) Layer 2 apps listen exclusively on chmod'ed sockets bridged by one of the layer 1 daemons. Layers 3+ inherit from layer 2 in a similar fashion. The two lines giving me grief are commented out at the very bottom of the *filter rules. The first line runs fine but it's all or nothing. :) Many thanks, Peter H. *nat #Flush previous rules, chains and counters for the 'nat' table -F -X -Z #Redirect traffic to alternate internal ports -I PREROUTING --src 0/0 -p tcp --dport 80 -j REDIRECT --to-ports 8080 -I PREROUTING --src 0/0 -p tcp --dport 443 -j REDIRECT --to-ports 8443 -I PREROUTING --src 0/0 -p udp --dport 53 -j REDIRECT --to-ports 8053 -I PREROUTING --src 0/0 -p tcp --dport 9022 -j REDIRECT --to-ports 8022 COMMIT *filter #Flush previous settings, chains and counters for the 'filter' table -F -X -Z #Set default behavior for all connections and protocols -P INPUT DROP -P OUTPUT DROP -A FORWARD -j DROP #Only accept loopback traffic originating from the local NIC -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j DROP #Accept all outgoing non-fragmented traffic having a valid state -A OUTPUT ! -f -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT #Drop fragmented incoming packets (Not always malicious - acceptable for use now) -A INPUT -f -j DROP #Allow ping requests rate limited to one per second (burst ensures reliable results for high latency connections) -A INPUT -p icmp --icmp-type 8 -m limit --limit 1/sec --limit-burst 2 -j ACCEPT #Declaration of custom chains -N INSPECT_TCP_FLAGS -N INSPECT_STATE -N INSPECT #Drop incoming tcp connections with invalid tcp-flags -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL ALL -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL NONE -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,FIN FIN -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,PSH PSH -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,URG URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL FIN,PSH,URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags FIN,RST FIN,RST -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags SYN,RST SYN,RST -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL SYN,FIN,PSH,URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL SYN,RST,ACK,FIN,URG -j DROP #Accept incoming traffic having either an established or related state -A INSPECT_STATE -m state --state ESTABLISHED,RELATED -j ACCEPT #Drop new incoming tcp connections if they aren't SYN packets -A INSPECT_STATE -m state --state NEW -p tcp ! --syn -j DROP #Drop incoming traffic with invalid states -A INSPECT_STATE -m state --state INVALID -j DROP #INSPECT chain definition -A INSPECT -p tcp -j INSPECT_TCP_FLAGS -A INSPECT -j INSPECT_STATE #Route incoming traffic through the INSPECT chain -A INPUT -j INSPECT #Accept redirected HTTP traffic via HA reverse proxy -A INPUT -p tcp --dport 8080 -j ACCEPT #Accept redirected HTTPS traffic via STUNNEL SSH gateway (As well as tunneled HTTPS traffic destine for other services) -A INPUT -p tcp --dport 8443 -j ACCEPT #Accept redirected DNS traffic for NSD authoritative nameserver -A INPUT -p udp --dport 8053 -j ACCEPT #Accept redirected SSH traffic for OpenSSH server #Temp solution: -A INPUT -p tcp --dport 8022 -j ACCEPT #Ideal solution: #Limit new ssh connections to max 10 per 10 minutes while allowing an "unlimited" (or better reasonably limited?) number of established connections. #-A INPUT -p tcp --dport 8022 --state NEW,ESTABLISHED -m recent --set -j ACCEPT #-A INPUT -p tcp --dport 8022 --state NEW -m recent --update --seconds 600 --hitcount 11 -j DROP COMMIT *mangle #Flush previous rules, chains and counters in the 'mangle' table -F -X -Z COMMIT

  Read the article

• DRBD not syncing between my nodes when IP is reset

  - by ramdaz

  I am trying to setup DRBD by following the article at http://www.howtoforge.com/setting-up-network-raid1-with-drbd-on-ubuntu-11.10-p2 I am using Ubuntu 10.04 DRBD - 8.3.11 In the first run I had everything working perfectly and when shifting the systems to a production environment I decided to restart the Meta Data creation part and start from scratch. The IPs had changed entirely in the production environment. Issuing drdbadm create-md r0 in both the servers runs successfully. But when I do "drbdadm -- --overwrite-data-of-peer primary all" on the primary it fails to start the re sync. My config file is as given below resource r0 { protocol C; syncer { rate 50M; } startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "aklsadkjlhdbskjndsf8738734jkfkjfkjf"; } on primaryds { device /dev/drbd0; disk /dev/md2; address 172.16.7.1:7788; meta-disk internal; } on secondaryds { device /dev/drbd0; disk /dev/md2; address 172.16.7.3:7788; meta-disk internal; } } Status on primary root at primaryds:~# cat /proc/drbd version: 8.3.7 (api:88/proto:86-91) GIT-hash: ea9e28dbff98e331a62bcbcc63a6135808fe2917 build by root at primaryds, 2012-05-12 15:08:01 0: cs:WFBitMapS ro:Primary/Secondary ds:UpToDate/Inconsistent C r---- ns:0 nr:0 dw:0 dr:200 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5690352828 Status on secondary root at secondaryds:/etc/drbd.d# cat /proc/drbd version: 8.3.7 (api:88/proto:86-91) GIT-hash: ea9e28dbff98e331a62bcbcc63a6135808fe2917 build by root at secondaryds, 2012-05-12 15:25:25 0: cs:WFBitMapT ro:Secondary/Primary ds:Inconsistent/UpToDate C r---- ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5690352828 Log of Primary May 30 13:42:23 primaryds kernel: [ 1584.057076] block drbd0: role( Secondary -> Primary ) disk( Inconsistent -> UpToDate ) May 30 13:42:23 primaryds kernel: [ 1584.086264] block drbd0: Forced to consider local data as UpToDate! May 30 13:42:23 primaryds kernel: [ 1584.086303] block drbd0: Creating new current UUID May 30 13:42:26 primaryds kernel: [ 1586.405551] block drbd0: drbd_sync_handshake: May 30 13:42:26 primaryds kernel: [ 1586.405564] block drbd0: self E8A075F378173D4B:0000000000000004:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:26 primaryds kernel: [ 1586.405574] block drbd0: peer 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:26 primaryds kernel: [ 1586.405582] block drbd0: uuid_compare()=2 by rule 30 May 30 13:42:26 primaryds kernel: [ 1586.405587] block drbd0: Becoming sync source due to disk states. May 30 13:42:26 primaryds kernel: [ 1586.405592] block drbd0: Writing the whole bitmap, full sync required after drbd_sync_handshake. May 30 13:42:27 primaryds kernel: [ 1588.171638] block drbd0: 5427 GB (1422588207 bits) marked out-of-sync by on disk bit-map. May 30 13:42:27 primaryds kernel: [ 1588.172769] block drbd0: conn( Connected -> WFBitMapS ) Log in Secondary May 30 13:42:24 secondaryds kernel: [ 1563.304894] block drbd0: peer( Secondary - Primary ) pdsk( Inconsistent - UpToDate ) May 30 13:42:24 secondaryds kernel: [ 1563.339674] block drbd0: drbd_sync_handshake: May 30 13:42:24 secondaryds kernel: [ 1563.339685] block drbd0: self 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:24 secondaryds kernel: [ 1563.339695] block drbd0: peer E8A075F378173D4B:0000000000000004:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:24 secondaryds kernel: [ 1563.339703] block drbd0: uuid_compare()=-2 by rule 20 May 30 13:42:24 secondaryds kernel: [ 1563.339709] block drbd0: Becoming sync target due to disk states. May 30 13:42:24 secondaryds kernel: [ 1563.339714] block drbd0: Writing the whole bitmap, full sync required after drbd_sync_handshake. May 30 13:42:26 secondaryds kernel: [ 1565.652342] block drbd0: 5427 GB (1422588207 bits) marked out-of-sync by on disk bit-map. May 30 13:42:26 secondaryds kernel: [ 1565.652965] block drbd0: conn( Connected - WFBitMapT ) The serves are not responding once it reaches this stage. Tried redoing it couple of time but noting happens. Why could the resync not be taking place? I would like some advice? Directions?

  Read the article

• Can't communicate between lan ports on openwrt router

  - by ScaryAardvark

  I've got a WBMR-HP-G300H Buffalo Airstation router on which I've installed the lates OpenWRT software. All is working well (ADSL, WIFI etc) except for one niggle. I can't communicate between lan ports. i.e. if I have one computer connected on lan port 1 and I try to ping another computer on lan port 2 then I get "destination unreachable". I can ping both computers from the router itself and can also ping each computer from a seperate laptop connected wirelessly. All computers are in the same subnet range (10.0.0.?/24). I suspect that I may need to configure a vlan on the switch but everytime I try and do this with various google'ed configuration I keep freezing out all lan-ports and I have to revert back using a wirelessly connected laptop. Here's my /etc/config/network: config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config interface 'lan' option type 'bridge' option proto 'static' option netmask '255.255.255.0' option ipaddr '10.0.0.1' option _orig_ifname 'eth0 wlan0' option _orig_bridge 'true' option ifname 'eth0' config adsl-device 'adsl' option fwannex 'a' option annex 'a2p' config interface 'wan' option _orig_ifname 'nas0' option _orig_bridge 'false' option proto 'pppoa' option encaps 'vc' option atmdev '0' option vci '38' option vpi '0' option username '?????????????' option password '??????????????' Any help would be warmly received. Here's some more config stuff. root@OpenWrt:~# ifconfig -a br-lan Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:226576 errors:0 dropped:346 overruns:0 frame:0 TX packets:269292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:26771676 (25.5 MiB) TX bytes:183986450 (175.4 MiB) eth0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb0 Link encap:Ethernet HWaddr 36:60:EC:DF:13:A1 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb1 Link encap:Ethernet HWaddr 4A:7B:75:67:54:E0 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:780 errors:0 dropped:0 overruns:0 frame:0 TX packets:780 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:58369 (57.0 KiB) TX bytes:58369 (57.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 00-24-A5-BD-66-08-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2424 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:320188 (312.6 KiB) TX bytes:0 (0.0 B) pppoa-wan Link encap:Point-to-Point Protocol inet addr:81.136.179.204 P-t-P:81.134.80.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:258894 errors:0 dropped:0 overruns:0 frame:0 TX packets:212976 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:177341656 (169.1 MiB) TX bytes:25192459 (24.0 MiB) wlan0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:204063 errors:0 dropped:0 overruns:0 frame:0 TX packets:245516 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:26613140 (25.3 MiB) TX bytes:162799765 (155.2 MiB) root@OpenWrt:~# brctl show bridge name bridge id STP enabled interfaces br-lan 8000.0024a5bd6608 no wlan0 eth0 root@OpenWrt:~# swconfig dev eth0 show Global attributes: enable_vlan: 0 Port 0: pvid: 0 link: port:0 link:up speed:1000baseT full-duplex txflow rxflow Port 1: pvid: 0 link: port:1 link:down Port 2: pvid: 0 link: port:2 link:down Port 3: pvid: 0 link: port:3 link:down Port 4: pvid: 0 link: port:4 link:up speed:100baseT full-duplex txflow rxflow auto Port 5: pvid: 0 link: port:5 link:up speed:100baseT full-duplex txflow rxflow auto Regards Mark.

  Read the article

• Setting up home DNS with Ubuntu Server

  - by Zeophlite

  I have a webserver (with static IP 192.168.1.5), and I want to have my machines on my local network to be able to access it without modifying /etc/hosts (or equivalent for Windows/OSX). My router has Primary DNS server 192.168.1.5 Secondary DNS server 8.8.8.8 (Google's public DNS). Nginx is set up to server websites externally as *.example.com Internally, I want *.example.local to point to the server. My webserver has BIND9 installed, but I'm unsure of the settings. I've been through various contradicting tutorials, and so most of my settings have been clobbered. I've stripped out the lines which I'm confused about. The tutorials I looked at are http://tech.surveypoint.com/blog/installing-a-local-dns-server-behind-a-hardware-router/ and http://ubuntuforums.org/showthread.php?t=236093 . They mostly differ on what should be put in /etc/bind/zones/db.example.local and /etc/bind/zones/db.192, so I've left the conflicting lines out below. Can someone suggest what the correct lines are to give my above behaviour (namely *.example.local pointing to 192.168.1.5)? /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.5 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.254 /etc/hostname avalon /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN /etc/bind/named.conf.options options { directory "/var/cache/bind"; forwarders { 8.8.8.8; 8.8.4.4; }; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.local zone "example.local" { type master; file "/etc/bind/zones/db.example.local"; }; zone "1.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/db.192"; }; /etc/bind/zones/db.example.local $TTL 604800 @ IN SOA avalon.example.local. webadmin.example.local. ( 5 ; Serial, increment each edit 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL /etc/bind/zones/db.192 $TTL 604800 @ IN SOA avalon.example.local. webadmin.example.local. ( 4 ; Serial, increment each edit 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; What do I need to add to the above files so that on a laptop on the internal network, I can type in webapp.example.local, and be served by my webserver? EDIT I made several changes to the above files on the webserver. /etc/network/interfaces (end of file) dns-nameservers 127.0.0.1 dns-search example.local /etc/bind/zones/db.example.local (end of file) @ IN NS avalon.example.local. @ IN A 192.168.1.5 avalon IN A 192.168.1.5 webapp IN A 192.168.1.5 www IN CNAME 192.168.1.5 /etc/bind/zones/db.192 (end of file) IN NS avalon.example.local. 73 IN PTR avalon.example.local. As a side note, my spare Win7 machine was able to connect directly to webapp.example.local, but for a Ubuntu 13.10 machine, I had to make the following changes as well (not on the webserver, but on a separate machine): /etc/nsswitch.conf before hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 after hosts: files dns /etc/NetworkManager/NetworkManager.conf before dns=dnsmasq after #dns=dnsmasq The issue remains that its not wildcard DNS, and so I have to add entries to /etc/bind/zones/db.example.local for webapp1, webapp2, ...

  Read the article

• KVM with one host IP and a different subnet for machines

  - by Jguy

  I've already setup a KVM host with proper IP configurations, but my host had me create DHCP and use that to assign the IP's to the machines. I want to see if there's an easier way to do it (or better). Upon my first setting out on this, I didn't find anything that pointed me in the right direction. I'm coming off a fresh install of Debian 6.0 x64, so I have nothing installed. I've logged in, queried for the below information and changed the password from my host set one. I have a Debian 6.0 x64 system with the following initial network configuration (substituted 255 in place of my real first octave): # tail /etc/network/interfaces auto eth0 iface eth0 inet static address 255.9.24.80 broadcast 255.9.24.95 netmask 255.255.255.224 gateway 255.9.24.65 # default route to access subnet up route add -net 255.9.24.64 netmask 255.255.255.224 gw 255.9.24.65 eth0 I have a /29 subnet that I want the virtual machines to use from my host: IP: 255.46.187.152 /29 Mask: 255.255.255.248 Broadcast: 255.46.187.159 Usable IP addresses: 255.46.187.153 to 255.46.187.158 I like the interface of Cloudmin, so I want to try and use that if I can to administrate my guests. So, my questions: How do I set this up on the host system the best so that I can use the additional Subnet IP's on the guests and have them accessible from the internet? I also need to host a DNS server, which means one of these VM's has to have two IP's assigned to it and accessable from the outside world. How can I do that using Cloudmin? I had a question about this here: Multiple IP addresses assigned to one KVM VM But I just reformatted the entire server and am trying to figure out a better way of doing this. Machine information: # ip route show 255.9.24.64/27 via 255.9.24.65 dev eth0 255.9.24.64/27 dev eth0 proto kernel scope link src 255.9.24.80 default via 255.9.24.65 dev eth0 brctl is empty # ip addr list 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether c8:60:00:54:b5:d8 brd ff:ff:ff:ff:ff:ff inet 255.9.24.80/27 brd 255.9.24.95 scope global eth0 inet6 fe80::ca60:ff:fe54:b5d8/64 scope link valid_lft forever preferred_lft forever Thank you for any help you can provide me. EDIT: I've installed kvm and cloudmin: aptitude install qemu-kvm libvirt-bin wget http://cloudmin.virtualmin.com/gpl/scripts/cloudmin-kvm-debian-install.sh ./cloudmin-kvm-debian-install.sh Rebooted and now my network configuration looks like this: # device: eth0 iface eth0 inet manual # default route to access subnet iface br0 inet static address 255.9.24.80 netmask 255.255.255.224 broadcast 255.9.24.95 network 255.9.24.64 bridge_ports eth0 gateway 255.9.24.65 I setup in Cloudmin the Start IP as 255.46.187.153 and End IP as 255.46.187.158. The CIDR is 29 and the gateway is 255.46.187.152. I've installed a guest with ubuntuserver 12.04 x64, which was able to get and retrieve internet resources during installation, but now cannot reach anything nor can it be reached from anything. Its network configuration is: iface eth0 inet static address 255.46.187.153 netmask 255.255.255.224 broadcast 255.46.187.159 gateway 255.46.187.152 dns-nameservers <host provided nameservers> And is not able to ping google.com through DNS or direct IP, I can't ping the VM from the outside or the host. any ideas now?

  Read the article

• How broken is routing strategy that causes a martian packet (so far only) during tracepath?

  - by lkraav

  I believe I've achieved a table that routes packets from and to eth1/192.168.3.x through 192.168.3.1, and packets from and to eth0/192.168.1.x through 192.168.1.1 (helpful source). Question: when doing tracepath from 192.168.3.20 (from within vserver), I'm getting kernel: [318535.927489] martian source 192.168.3.20 from 212.47.223.33, on dev eth0 at or near the target IP, while intermediary hops go without (log below). I don't understand why this packet is arriving on eth0, instead of eth1, even after reading this: Note that you may see packets from non-routable IP addresses when running the traceroute or tracepath commands. While packets cannot be routed to these routers, packets sent between 2 routers only need to know the address of the next hop within the local networks, which could be a non-routable address. Can someone explain that paragraph in human language? Based on short initial trials so far, everything else seems to work without causing martians. Is this contained to the nature of tracepath operation or do I have some other bigger routing problem that will cause work traffic breakage? Side note: is it possible to inspect martian packet with tcpdump or wireshark or anything of the sort? I'm have not been able to get it to show up on my own. vserver-20 / # tracepath -n 212.47.223.33 1: 192.168.3.2 0.064ms pmtu 1500 1: 192.168.3.1 1.076ms 1: 192.168.3.1 1.259ms 2: 90.191.8.2 1.908ms 3: 90.190.134.194 2.595ms 4: 194.126.123.94 2.136ms asymm 5 5: 195.250.170.22 2.266ms asymm 6 6: 212.47.201.86 2.390ms asymm 7 7: no reply 8: no reply 9: no reply ^C Host routing: $ sudo ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:24:1d:de:b3:5d brd ff:ff:ff:ff:ff:ff inet 192.168.1.2/24 scope global eth0 4: eth1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:46:46:a3:6a brd ff:ff:ff:ff:ff:ff inet 192.168.3.2/27 scope global eth1 inet 192.168.3.20/27 brd 192.168.3.31 scope global secondary eth1 # linux-vserver instance $ sudo ip route default via 192.168.1.1 dev eth0 metric 3 unreachable 127.0.0.0/8 scope host 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.2 192.168.3.0/27 dev eth1 proto kernel scope link src 192.168.3.2 $ sudo ip rule 0: from all lookup local 32764: from all to 192.168.3.0/27 lookup dmz 32765: from 192.168.3.0/27 lookup dmz 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table dmz default via 192.168.3.1 dev eth1 metric 4 192.168.3.0/27 dev eth1 scope link metric 4 Gateway routing # ip route 10.24.0.2 dev tun0 proto kernel scope link src 10.24.0.1 10.24.0.0/24 via 10.24.0.2 dev tun0 192.168.3.0/24 dev br-dmz proto kernel scope link src 192.168.3.1 192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1 $ISP_NET/23 dev eth0.1 proto kernel scope link src $WAN_IP default via $ISP_GW dev eth0.1 Additional background Options for non-virtualized network interface isolation?

  Read the article

• ¿Es más barato desarrollar a medida que adquirir un ERP?

  - by Luis Alberto Quilez

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} La clave está en el tiempo. Cuando abordamos un desarrollo a medida, estamos pensando únicamente en las necesidades de hoy. Tenemos un proyecto concreto, un determinado alcance funcional y conocemos las herramientas que hoy tenemos disponibles. Somos los que mejor conocemos nuestra empresa de hoy, sus procesos y el desarrollo parece una buena opción, pues las licencias de las herramientas de desarrollo son económicas y el coste de la tarifa diaria de programación es asequible, y entonces, caemos en la trampa del corto plazo y vamos adelante. Es muy posible que este desarrollo salga bien, que estemos orgullosos de nuestro trabajo, e incluso que proclamemos a los 4 vientos el dinero que nos hemos ahorrado. Sin embargo el mundo no se para, el negocio no se para, la adaptación debe ser permanente, nuestros clientes, internos y externos, tendrán nuevas exigencias y nuestro desarrollo no estará terminado, tendremos que integrarlo con otras áreas, tendremos que tratar de darle mayor funcionalidad y alcance, tendremos que adaptarlo a las nuevas tecnologías, permitir que la información se analice, se comparta, se acceda desde nuevos dispositivos … y veremos en primera persona cómo la trampa del desarrollo se cierra sobre nuestras cabezas, nunca estará terminado, la tecnología que usamos un día se quedará obsoleta, el ritmo de exigencia por funcionalidad e integración será cada vez mayor y no podremos sino poner más y más recursos dedicados al mantenimiento de un desarrollo propio, que no deja de comer, que me obliga a gastar más y más cada día y del que no puedo salir. Al poco tiempo me he convertido en una empresa de desarrollo de software dentro de mi propia empresa y ni tengo los recursos económicos para hacerlo viable, ni tengo las capacidades humanas y de inversión para responder a lo que se me exige desde el negocio. Así que pensemos, desde el principio, en que nuestra empresa debe perdurar muchos años, y hagamos el análisis de costes bajo esta perspectiva a la hora de tomar la decisión y veremos entonces que la adquisición de un ERP es mucho más económica que el desarrollo a medida. Por otro lado tenemos la integración. Un sistema de producción, requiere la asignación de recursos, que a su vez requieren de un plan de desarrollo, una formación o un cálculo de su nómina; también requiere de una cuenta contable, de una gestión de compras o de una asignación de costes y claro,de todos estos puntos nos vamos dando cuenta sobre la marcha, cuando en un sistema de gestión integral (ERP) lo tenemos disponible desde el primer momento. Claro que no nos vale un ERP cerrado, poco flexible y que no me permita diferenciar a mi empresa. Tenemos que buscar un socio tecnológico que nos acompañe, que asuma la inversión en tecnología y que me vaya suministrando versiones y soluciones acordes a las exigencias de los tiempos, de hoy y de mañana, pero además que me permita adaptar los flujos e innovar en los procesos para que podamos diferenciar nuestra empresa de la competencia, hoy y mañana. Veremos cómo, con la decisión de un ERP, flexible y abierto, los números salen y en el largo plazo es mucho más económica la decisión de adquirir un ERP que de optar por el desarrollo. Luis Alberto Quilez v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

  Read the article

• 13.10 - Weird WiFi connection problems - WMP300N - Broadcom BCM4321

  - by user1898041

  Just installed 13.10 on my desktop and I really like it. After having problems with getting the wifi to work, I installed it connected to the internet with an ethernet cable and added in the 3rd party software and updates as per the installation procedure. After installation was completed, I saw the wifi icon in the upper right hand corner, but it was not seeing any wifi networks. Some Googling brought me to use the 'Additional Drivers' application. It found the WMP300N Broadcom BDM4321 based pci wifi card and installed the proprietary Broadcom STA wireless driver, which may have been installed before. I'm not sure. Here is the weird part: when I start my system, wifi seems to be in some sort of suspended state where the system sees that the card exists but the card will not detect any wifi networks. It will work after booting once I 'Additional Drivers' application and then start FireFox. I know it seems weird, but this is the process I've got down to get the card to recognize wifi networks. After those applications are open for a few seconds, the card starts to function like normal (although maintaining the wifi connection is problem but most likely a seperate issue). The reason this is a problem is because this is supposed to just be a headless box managed through SSH. Here are the readouts from the common network diagnosis programs BEFORE I open 'Additional Drivers' and 'FireFox'. All commands were done with sudo. lspci 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82G35 Express PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Qualcomm Atheros Attansic L1 Gigabit Ethernet (rev b0) 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller 05:00.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 01) 05:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) - lshw *-network description: Ethernet interface product: Attansic L1 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: b0 serial: 00:22:15:00:a8:12 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.1.3 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:feac0000-feafffff memory:feaa0000-feabffff *-network description: Wireless interface product: BCM4321 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 00:23:69:d8:2b:16 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) latency=64 multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:febfc000-febfffff - ifconfig eth0 Link encap:Ethernet HWaddr 00:22:15:00:a8:12 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:23:69:d8:2b:16 inet6 addr: fe80::223:69ff:fed8:2b16/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) - iwconfig eth1 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=200 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off - iwlist scan eth1 No scan results - Here are the various commands AFTER I open 'Additional Drivers' and 'FireFox' lspci 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82G35 Express PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Qualcomm Atheros Attansic L1 Gigabit Ethernet (rev b0) 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller 05:00.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 01) 05:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) - lshw *-network description: Ethernet interface product: Attansic L1 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: b0 serial: 00:22:15:00:a8:12 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.1.3 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:feac0000-feafffff memory:feaa0000-feabffff *-network description: Wireless interface product: BCM4321 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 00:23:69:d8:2b:16 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.103 latency=64 multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:febfc000-febfffff - ifconfig eth0 Link encap:Ethernet HWaddr 00:22:15:00:a8:12 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:23:69:d8:2b:16 inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:69ff:fed8:2b16/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:85 errors:0 dropped:0 overruns:0 frame:11901 TX packets:132 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52641 (52.6 KB) TX bytes:19058 (19.0 KB) Interrupt:16 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6084 (6.0 KB) TX bytes:6084 (6.0 KB) - iwconfig eth1 IEEE 802.11abg ESSID:"BU" Mode:Managed Frequency:2.447 GHz Access Point: 00:26:F2:1F:81:02 Bit Rate=54 Mb/s Tx-Power=200 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=59/70 Signal level=-51 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 - iwlist scan A LOT OF SSIDs FOUND! - I'd like to have this problem fixed, but I'm not quite sure where to go. Been Googling a lot and can't seem to find anyone else with this problem.

  Read the article

• Network Access: I can't access 192.168.1.101 from 192.168.1.102.

  - by takpar

  Hi, I'm running Ubuntu 10.04 on my PC with IP 192.168.1.101. every thing work fine, e.g. my web server is running and I can see http://localhost/ or http://192.168.1.101 properly. But the problem is that I cannot see my PC from my laptop at 192.168.1.102 e.g. at my laptop http://192.168.1.101 gives Connection timed out in browser. or trying to telnet on any port leads to: telnet: Unable to connect to remote host: Connection timed out laptop is running a fresh install of Ubuntu as well and there is no setup for firewall stuff in both computers. PS: Both computers can ping each other well. The router is a cicso linksys wireless ADSL modem. Currently, I can connect to FTP server on the Windows running on 192.168.1.102 from 192.168.1.101 without problem. Theses are commands ran on my PC, 192.168.1.101: ifconfig: adp@adp-desktop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:26:18:e1:8e:cf inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe70::226:18ff:fee1:8ecf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1831935 errors:0 dropped:0 overruns:0 frame:0 TX packets:1493786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1996855925 (1.9 GB) TX bytes:215288238 (215.2 MB) Interrupt:27 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:951742 errors:0 dropped:0 overruns:0 frame:0 TX packets:951742 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:494351095 (494.3 MB) TX bytes:494351095 (494.3 MB) vmnet1 Link encap:Ethernet HWaddr 00:50:46:c0:00:01 inet addr:192.168.91.1 Bcast:192.168.91.255 Mask:255.255.255.0 inet6 addr: fe70::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:50 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vmnet8 Link encap:Ethernet HWaddr 00:50:46:c0:00:08 inet addr:192.168.156.1 Bcast:192.168.156.255 Mask:255.255.255.0 inet6 addr: fe70::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) port 80 is set to 0.0.0.0 well: adp@adp-desktop:~$ netstat -ln | grep 'LISTEN ' tcp 0 0 127.0.0.1:52815 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4559 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4369 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:7634 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:21 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5269 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:25 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5280 0.0.0.0:* LISTEN tcp 0 0 127.0.1.1:7777 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:33601 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5222 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN tcp6 0 0 :::139 :::* LISTEN tcp6 0 0 ::1:631 :::* LISTEN tcp6 0 0 :::445 :::* LISTEN /etc/hosts.deny is empty: adp@adp-desktop:~$ cat /etc/hosts.deny # /etc/hosts.deny: list of hosts that are _not_ allowed to access the system. # See the manual pages hosts_access(5) and hosts_options(5). # # Example: ALL: some.host.name, .some.domain # ALL EXCEPT in.fingerd: other.host.name, .other.domain # # If you're going to protect the portmapper use the name "portmap" for the # daemon name. Remember that you can only use the keyword "ALL" and IP # addresses (NOT host or domain names) for the portmapper, as well as for # rpc.mountd (the NFS mount daemon). See portmap(8) and rpc.mountd(8) # for further information. # # The PARANOID wildcard matches any host whose name does not match its # address. # # You may wish to enable this to ensure any programs that don't # validate looked up hostnames still leave understandable logs. In past # versions of Debian this has been the default. # ALL: PARANOID netstat -l: adp@adp-desktop:~$ netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 localhost:52815 *:* LISTEN tcp 0 0 *:hylafax *:* LISTEN tcp 0 0 *:www *:* LISTEN tcp 0 0 *:4369 *:* LISTEN tcp 0 0 localhost:7634 *:* LISTEN tcp 0 0 *:ftp *:* LISTEN tcp 0 0 *:xmpp-server *:* LISTEN tcp 0 0 localhost:ipp *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 *:5280 *:* LISTEN tcp 0 0 adp-desktop:7777 *:* LISTEN tcp 0 0 *:33601 *:* LISTEN tcp 0 0 *:xmpp-client *:* LISTEN tcp 0 0 localhost:mysql *:* LISTEN tcp6 0 0 [::]:netbios-ssn [::]:* LISTEN tcp6 0 0 localhost:ipp [::]:* LISTEN tcp6 0 0 [::]:microsoft-ds [::]:* LISTEN udp 0 0 *:bootpc *:* udp 0 0 *:mdns *:* udp 0 0 *:47467 *:* udp 0 0 192.168.1.10:netbios-ns *:* udp 0 0 192.168.91.1:netbios-ns *:* udp 0 0 192.168.156.:netbios-ns *:* udp 0 0 *:netbios-ns *:* udp 0 0 192.168.1.1:netbios-dgm *:* udp 0 0 192.168.91.:netbios-dgm *:* udp 0 0 192.168.156:netbios-dgm *:* udp 0 0 *:netbios-dgm *:* raw 0 0 *:icmp *:* 7 netstat -rn: adp@adp-desktop:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.91.0 0.0.0.0 255.255.255.0 U 0 0 0 vmnet1 192.168.156.0 0.0.0.0 255.255.255.0 U 0 0 0 vmnet8 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 commands on the laptop, 192.168.1.102: ifconfig: root@fakeuser-laptop:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:33:a2:31:15 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:21 eth1 Link encap:Ethernet HWaddr 00:2d:d9:3e:1f:6c inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe70::21d:d9ff:fe3e:1f6c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5681 errors:0 dropped:0 overruns:0 frame:10313 TX packets:6717 errors:6 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4055251 (4.0 MB) TX bytes:779308 (779.3 KB) Interrupt:18 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:206 errors:0 dropped:0 overruns:0 frame:0 TX packets:206 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15172 (15.1 KB) TX bytes:15172 (15.1 KB) netstat -rn: root@fakeuser-laptop:~# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1

  Read the article

• How to configure TATA Photon+ EC1261 HUAWEI

  - by user3215

  I'm running ubuntu 10.04. I have a newly purchased TATA Photon+ Internet connection which supports Windows and Mac. On the Internet I found a article saying that it could be configured on Linux. I followed the steps to install it on Ubuntu from this link. I am still not able to get online, and need some help. Also, it is very slow, but I was told that I would see speeds up to 3.1MB. I dont have wvdial installed and cannot install it from apt as I'm not connected to internet Booting from windows I dowloaded "wvdial" .deb package and tried to install on ubuntu but it's ended with dependency problem. Automatically, don't know how, I got connected to internet only for once. Immediately I installed wvdial package after this I followed the tutorials(I could not browse and upload the files here) . From then it's showing that the device is connected in the network connections but no internet connection. Once I disable the device, it won't show as connected again and I'll have to restart my system. Sometimes the device itself not detected(wondering if there is any command to re-read the all devices). output of wvdialconf /etc/wvdial.cof: #wvdialconf /etc/wvdial.conf Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Modem Port Scan<*1>: S1 S2 S3 WvModem<*1>: Cannot get information for serial port. ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. WvModem<*1>: Cannot get information for serial port. ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. WvModem<*1>: Cannot get information for serial port. ttyUSB2<*1>: ATQ0 V1 E1 -- OK ttyUSB2<*1>: ATQ0 V1 E1 Z -- OK ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- OK ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK ttyUSB2<*1>: Modem Identifier: ATI -- Manufacturer: +GMI: HUAWEI TECHNOLOGIES CO., LTD ttyUSB2<*1>: Speed 9600: AT -- OK ttyUSB2<*1>: Max speed is 9600; that should be safe. ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK Found a modem on /dev/ttyUSB2. Modem configuration written to /etc/wvdial.conf. ttyUSB2<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" output of wvdial: #wvdial --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Sending: AT+CRM=1 AT+CRM=1 OK --> Modem initialized. --> Sending: ATDT#777 --> Waiting for carrier. ATDT#777 CONNECT --> Carrier detected. Starting PPP immediately. --> Starting pppd at Sat Oct 16 15:30:47 2010 --> Pid of pppd: 5681 --> Using interface ppp0 --> pppd: (u;[08]@s;[08]`{;[08] --> pppd: (u;[08]@s;[08]`{;[08] --> pppd: (u;[08]@s;[08]`{;[08] --> pppd: (u;[08]@s;[08]`{;[08] --> pppd: (u;[08]@s;[08]`{;[08] --> pppd: (u;[08]@s;[08]`{;[08] --> local IP address 14.96.147.104 --> pppd: (u;[08]@s;[08]`{;[08] --> remote IP address 172.29.161.223 --> pppd: (u;[08]@s;[08]`{;[08] --> primary DNS address 121.40.152.90 --> pppd: (u;[08]@s;[08]`{;[08] --> secondary DNS address 121.40.152.100 --> pppd: (u;[08]@s;[08]`{;[08] Output of log message /var/log/messages: Oct 16 15:29:44 avyakta-desktop pppd[5119]: secondary DNS address 121.242.190.180 Oct 16 15:29:58 desktop pppd[5119]: Terminating on signal 15 Oct 16 15:29:58 desktop pppd[5119]: Connect time 0.3 minutes. Oct 16 15:29:58 desktop pppd[5119]: Sent 0 bytes, received 177 bytes. Oct 16 15:29:58 desktop pppd[5119]: Connection terminated. Oct 16 15:30:47 desktop pppd[5681]: pppd 2.4.5 started by root, uid 0 Oct 16 15:30:47 desktop pppd[5681]: Using interface ppp0 Oct 16 15:30:47 desktop pppd[5681]: Connect: ppp0 <--> /dev/ttyUSB2 Oct 16 15:30:47 desktop pppd[5681]: CHAP authentication succeeded Oct 16 15:30:47 desktop pppd[5681]: CHAP authentication succeeded Oct 16 15:30:48 desktop pppd[5681]: local IP address 14.96.147.104 Oct 16 15:30:48 desktop pppd[5681]: remote IP address 172.29.161.223 Oct 16 15:30:48 desktop pppd[5681]: primary DNS address 121.40.152.90 Oct 16 15:30:48 desktop pppd[5681]: secondary DNS address 121.40.152.100 EDIT 1 : I tried the following sudo stop network-manager sudo killall modem-manager sudo /usr/sbin/modem-manager --debug > ~/mm.log 2>&1 & sudo /usr/sbin/NetworkManager --no-daemon > ~/nm.log 2>&1 & Output of mm.log: #vim ~/mm.log: ** Message: Loaded plugin Option High-Speed ** Message: Loaded plugin Option ** Message: Loaded plugin Huawei ** Message: Loaded plugin Longcheer ** Message: Loaded plugin AnyData ** Message: Loaded plugin ZTE ** Message: Loaded plugin Ericsson MBM ** Message: Loaded plugin Sierra ** Message: Loaded plugin Generic ** Message: Loaded plugin Gobi ** Message: Loaded plugin Novatel ** Message: Loaded plugin Nokia ** Message: Loaded plugin MotoC Output of nm.log: #vim ~/nm.log: NetworkManager: <info> starting... NetworkManager: <info> modem-manager is now available NetworkManager: SCPlugin-Ifupdown: init! NetworkManager: SCPlugin-Ifupdown: update_system_hostname NetworkManager: SCPluginIfupdown: guessed connection type (eth0) = 802-3-ethernet NetworkManager: SCPlugin-Ifupdown: update_connection_setting_from_if_block: name:eth0, type:802-3-ethernet, id:Ifupdown (eth0), uuid: 681b428f-beaf-8932-dce4-678ed5bae28e NetworkManager: SCPlugin-Ifupdown: addresses count: 1 NetworkManager: SCPlugin-Ifupdown: No dns-nameserver configured in /etc/network/interfaces NetworkManager: nm-ifupdown-connection.c.119 - invalid connection read from /etc/network/interfaces: (1) addresses NetworkManager: SCPluginIfupdown: management mode: unmanaged NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:14.4/0000:02:02.0/net/eth1, iface: eth1) NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:14.4/0000:02:02.0/net/eth1, iface: eth1): no ifupdown configuration found. NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/lo, iface: lo) @

  Read the article

• Linux router: ping doesn't route back

  - by El Barto

  I have a Debian box which I'm trying to set up as a router and an Ubuntu box which I'm using as a client. My problem is that when the Ubuntu client tries to ping a server on the Internet, all the packets are lost (though, as you can see below, they seem to go to the server and back without problem). I'm doing this in the Ubuntu Box: # ping -I eth1 my.remote-server.com PING my.remote-server.com (X.X.X.X) from 10.1.1.12 eth1: 56(84) bytes of data. ^C --- my.remote-server.com ping statistics --- 13 packets transmitted, 0 received, 100% packet loss, time 12094ms (I changed the name and IP of the remote server for privacy). From the Debian Router I see this: # tcpdump -i eth1 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 7, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 8, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 8, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 9, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 9, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 10, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 10, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 305, seq 11, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 305, seq 11, length 64 ^C 9 packets captured 9 packets received by filter 0 packets dropped by kernel # tcpdump -i eth2 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth2, link-type EN10MB (Ethernet), capture size 65535 bytes IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 213, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 213, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 214, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 214, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 215, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 215, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 216, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 216, length 64 IP 192.168.1.10 > X.X.X.X: ICMP echo request, id 360, seq 217, length 64 IP X.X.X.X > 192.168.1.10: ICMP echo reply, id 360, seq 217, length 64 ^C 10 packets captured 10 packets received by filter 0 packets dropped by kernel And at the remote server I see this: # tcpdump -i eth0 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 96 bytes IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 1, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 1, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 2, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 2, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 3, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 3, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 4, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 4, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 5, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 5, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 6, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 6, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 7, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 7, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 8, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 8, length 64 IP Y.Y.Y.Y > X.X.X.X: ICMP echo request, id 360, seq 9, length 64 IP X.X.X.X > Y.Y.Y.Y: ICMP echo reply, id 360, seq 9, length 64 18 packets captured 228 packets received by filter 92 packets dropped by kernel Here "X.X.X.X" is my remote server's IP and "Y.Y.Y.Y" is my local network's public IP. So, what I understand is that the ping packets are coming out of the Ubuntu box (10.1.1.12), to the router (10.1.1.1), from there to the next router (192.168.1.1) and reaching the remote server (X.X.X.X). Then they come back all the way to the Debian router, but they never reach the Ubuntu box back. What am I missing? Here's the Debian router setup: # ifconfig eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:105761 errors:0 dropped:0 overruns:0 frame:0 TX packets:48944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:40298768 (38.4 MiB) TX bytes:44831595 (42.7 MiB) Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38335992 errors:0 dropped:0 overruns:0 frame:0 TX packets:37097705 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:4260680226 (3.9 GiB) TX bytes:3759806551 (3.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3408 errors:0 dropped:0 overruns:0 frame:0 TX packets:3408 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:358445 (350.0 KiB) TX bytes:358445 (350.0 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:2767779 errors:0 dropped:0 overruns:0 frame:0 TX packets:1569477 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3609469393 (3.3 GiB) TX bytes:96113978 (91.6 MiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 # arp -n # Note: Here I have changed all the different MACs except the ones corresponding to the Ubuntu box (on 10.1.1.12 and 192.168.1.12) Address HWtype HWaddress Flags Mask Iface 192.168.1.118 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.72 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.94 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.102 ether NN:NN:NN:NN:NN:NN C eth2 10.1.1.12 ether 00:1e:67:15:2b:f0 C eth1 192.168.1.86 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.2 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.61 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.64 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.116 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.91 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.52 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.93 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.87 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.92 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.100 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.40 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.53 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.83 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.89 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.12 ether 00:1e:67:15:2b:f1 C eth2 192.168.1.77 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.66 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.90 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.65 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.41 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.78 ether NN:NN:NN:NN:NN:NN C eth2 192.168.1.123 ether NN:NN:NN:NN:NN:NN C eth2 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- 10.1.1.0/24 !10.1.1.0/24 MASQUERADE all -- !10.1.1.0/24 10.1.1.0/24 Chain OUTPUT (policy ACCEPT) target prot opt source destination And here's the Ubuntu box: # ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:67:15:2b:f1 inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe15:2bf1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28785139 errors:0 dropped:0 overruns:0 frame:0 TX packets:19050735 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32068182803 (32.0 GB) TX bytes:6061333280 (6.0 GB) Interrupt:16 Memory:b1a00000-b1a20000 eth1 Link encap:Ethernet HWaddr 00:1e:67:15:2b:f0 inet addr:10.1.1.12 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe15:2bf0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:285086 errors:0 dropped:0 overruns:0 frame:0 TX packets:12719 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30817249 (30.8 MB) TX bytes:2153228 (2.1 MB) Interrupt:16 Memory:b1900000-b1920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:86048 errors:0 dropped:0 overruns:0 frame:0 TX packets:86048 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11426538 (11.4 MB) TX bytes:11426538 (11.4 MB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.1.1 0.0.0.0 UG 100 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.8.0.0 192.168.1.10 255.255.255.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 # arp -n # Note: Here I have changed all the different MACs except the ones corresponding to the Debian box (on 10.1.1.1 and 192.168.1.10) Address HWtype HWaddress Flags Mask Iface 192.168.1.70 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.90 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.97 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.103 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.13 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.120 (incomplete) eth0 192.168.1.111 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.118 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.51 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.102 (incomplete) eth0 192.168.1.64 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.52 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.74 (incomplete) eth0 192.168.1.94 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.121 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.72 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.87 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.91 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.71 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.78 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.83 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.88 (incomplete) eth0 192.168.1.82 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.98 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.100 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.93 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.73 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.11 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.85 (incomplete) eth0 192.168.1.112 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.89 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.65 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.81 ether NN:NN:NN:NN:NN:NN C eth0 10.1.1.1 ether 94:0c:6d:82:0d:98 C eth1 192.168.1.53 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.116 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.61 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.10 ether 6c:f0:49:a4:47:38 C eth0 192.168.1.86 (incomplete) eth0 192.168.1.119 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.66 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth0 192.168.1.1 ether NN:NN:NN:NN:NN:NN C eth1 192.168.1.92 ether NN:NN:NN:NN:NN:NN C eth0 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination Edit: Following Patrick's suggestion, I did a tcpdump con the Ubuntu box and I see this: # tcpdump -i eth1 -qtln icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 1, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 1, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 2, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 2, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 3, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 3, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 4, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 4, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 5, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 5, length 64 IP 10.1.1.12 > X.X.X.X: ICMP echo request, id 21967, seq 6, length 64 IP X.X.X.X > 10.1.1.12: ICMP echo reply, id 21967, seq 6, length 64 ^C 12 packets captured 12 packets received by filter 0 packets dropped by kernel So the question is: if all packets seem to be coming and going, why does ping report 100% packet loss?

  Read the article

• Xapian gem failed to install on Mac OS X Snow Leopard + macports

  - by goodwill

  I have installed xapian-core + xapian-bindings with macports on snow leopard, then trying to install xapian gem fails: Building native extensions. This could take a while... ERROR: Error installing xapian: ERROR: Failed to build gem native extension. /opt/ruby-enterprise/bin/ruby extconf.rb ./configure --with-ruby checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for a thread-safe mkdir -p... ./install-sh -c -d checking for gawk... no checking for mawk... no checking for nawk... no checking for awk... awk checking whether make sets $(MAKE)... yes checking how to create a ustar tar archive... gnutar checking build system type... i386-apple-darwin10.3.0 checking host system type... i386-apple-darwin10.3.0 checking for style of include used by make... GNU checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... none needed checking dependency style of gcc... gcc3 checking for a sed that does not truncate output... /usr/bin/sed checking for grep that handles long lines and -e... /usr/bin/grep checking for egrep... /usr/bin/grep -E checking for ld used by gcc... /usr/libexec/gcc/i686-apple-darwin10/4.2.1/ld checking if the linker (/usr/libexec/gcc/i686-apple-darwin10/4.2.1/ld) is GNU ld... no checking for /usr/libexec/gcc/i686-apple-darwin10/4.2.1/ld option to reload object files... -r checking for BSD-compatible nm... /usr/bin/nm checking whether ln -s works... yes checking how to recognize dependent libraries... pass_all checking how to run the C preprocessor... gcc -E checking for ANSI C header files... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking dlfcn.h usability... yes checking dlfcn.h presence... yes checking for dlfcn.h... yes checking for g++... g++ checking whether we are using the GNU C++ compiler... yes checking whether g++ accepts -g... yes checking dependency style of g++... gcc3 checking how to run the C++ preprocessor... g++ -E checking the maximum length of command line arguments... 196608 checking command to parse /usr/bin/nm output from gcc object... ok checking for objdir... .libs checking for ar... ar checking for ranlib... ranlib checking for strip... strip checking for dsymutil... dsymutil checking for nmedit... nmedit checking for -single_module linker flag... yes checking for -exported_symbols_list linker flag... yes checking if gcc supports -fno-rtti -fno-exceptions... no checking for gcc option to produce PIC... -fno-common checking if gcc PIC flag -fno-common works... yes checking if gcc static flag -static works... no checking if gcc supports -c -o file.o... yes checking whether the gcc linker (/usr/libexec/gcc/i686-apple-darwin10/4.2.1/ld) supports shared libraries... yes checking dynamic linker characteristics... darwin10.3.0 dyld checking how to hardcode library paths into programs... immediate checking whether stripping libraries is possible... yes checking if libtool supports shared libraries... yes checking whether to build shared libraries... yes checking whether to build static libraries... no checking whether we are using the GNU C++ compiler... (cached) yes checking whether g++ accepts -g... (cached) yes checking dependency style of g++... (cached) gcc3 checking for xapian-config... /opt/local/bin/xapian-config checking /opt/local/bin/xapian-config works... yes checking whether to enable maintainer-specific portions of Makefiles... no checking for ruby1.8... no checking for ruby... /opt/ruby-enterprise/bin/ruby checking /opt/ruby-enterprise/bin/ruby version... ruby 1.8.7 (2009-06-12 patchlevel 174) [i686-darwin10.2.0], MBARI 0x6770, Ruby Enterprise Edition 2009.10 checking for /opt/ruby-enterprise/lib/ruby/1.8/i686-darwin10.2.0/ruby.h... yes checking ruby/io.h... no checking whether to use -fvisibility=hidden... yes configure: creating ./config.status config.status: creating Makefile config.status: creating xapian-version.h config.status: creating python/Makefile config.status: creating python/docs/Makefile config.status: creating php/Makefile config.status: creating php/docs/Makefile config.status: creating java/Makefile config.status: creating java/native/Makefile config.status: creating java/org/xapian/Makefile config.status: creating java/org/xapian/errors/Makefile config.status: creating java/org/xapian/examples/Makefile config.status: creating java-swig/Makefile config.status: creating tcl8/Makefile config.status: creating tcl8/docs/Makefile config.status: creating tcl8/pkgIndex.tcl config.status: creating csharp/Makefile config.status: creating csharp/docs/Makefile config.status: creating csharp/AssemblyInfo.cs config.status: creating ruby/Makefile config.status: creating ruby/docs/Makefile config.status: creating xapian-bindings.spec config.status: creating python/generate-python-exceptions config.status: creating config.h config.status: config.h is unchanged config.status: executing depfiles commands *** Building bindings for languages: ruby make make all-recursive Making all in ruby make all-recursive Making all in docs make all-am make[5]: Nothing to be done for `all-am'. /bin/sh ../libtool --tag=CXX --mode=compile g++ -DHAVE_CONFIG_H -I. -I.. -I/opt/ruby-enterprise/lib/ruby/1.8/i686-darwin10.2.0 -I/opt/ruby-enterprise/lib/ruby/1.8/i686-darwin10.2.0 -fno-strict-aliasing -Wall -Wno-unused -Wno-uninitialized -fvisibility=hidden -I/opt/local/include -g -O2 -MT xapian_wrap.lo -MD -MP -MF .deps/xapian_wrap.Tpo -c -o xapian_wrap.lo xapian_wrap.cc ../libtool: line 393: /bin/sed: No such file or directory ../libtool: line 393: /bin/sed: No such file or directory ../libtool: line 792: /bin/sed: No such file or directory : ignoring unknown tag ../libtool: line 792: /bin/sed: No such file or directory *** Warning: inferring the mode of operation is deprecated. *** Future versions of Libtool will require --mode=MODE be specified. ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1103: /bin/sed: No such file or directory ../libtool: line 1156: /bin/sed: No such file or directory : compile: cannot determine name of library object from `' make[4]: *** [xapian_wrap.lo] Error 1 make[3]: *** [all-recursive] Error 1 make[2]: *** [all] Error 2 make[1]: *** [all-recursive] Error 1 make: *** [all] Error 2 extconf.rb:3:in `system!': unhandled exception from extconf.rb:6 Gem files will remain installed in /opt/ruby-enterprise/lib/ruby/gems/1.8/gems/xapian-1.0.15 for inspection. Results logged to /opt/ruby-enterprise/lib/ruby/gems/1.8/gems/xapian-1.0.15/gem_make.out Any idea pal?

  Read the article

• Weird FTP issue between Unity Express and Windows Server 2008 FTP

  - by user33975

  My VOIP specialist complained about not being able to run backups of the Unity Express onto our FTP server (Microsoft FTP on Server 2008). I did a packet trace and observed some weird behavior that I think is even kind of funny in a way. The Unity FTP client is able to initiate both control and data connections with no problem, even being able to LIST directories and CWD into them. But as soon as the client sends a SYST command (not sure why it cares), the server replies with "Windows_NT" and lo and behold...the client immediately sends a QUIT command! I've seen this happen consistently on my packet captures. I tried pointing the Unity FTP client to a FileZilla FTP server, and viola...it worked fine! Has anyone else observed this? I thought it was kinda funny, being that Cisco seems to not like Microsoft that much...

  Read the article

• Can't connect to website after altering IPTables

  - by user2833135

  I attempted to open up a port on my VPS, but I can't connect to my website after opening up that port. Below are the commands I issued to open the port. I didn't get an error or anything after setting this up. I just can't connect to my website after doing this. [root@vps ~]# iptables -F [root@vps ~]# iptables -A INPUT -i lo -j ACCEPT [root@vps ~]# iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT [root@vps ~]# iptables -A INPUT -p tcp --dport 25765 -j ACCEPT [root@vps ~]# iptables -P INPUT DROP [root@vps ~]# iptables -P FORWARD DROP [root@vps ~]# iptables -P OUTPUT ACCEPT [root@vps ~]# iptables -L -v Just a side note, but I am running CentOS 6 (64 bit) Thank you in advance.

  Read the article

• Reset DRAC/MC password on Dell BladeCentre 1855

  - by Farseeker

  I have a Dell Blade Centre 1855, and nobody knows what the root password for the DRAC/MC card in the blade chassis is (I tried root/calvin). I do not have IP access to the DRAC/MC, nor do I have physical access to the back of the blade centre to access the DRAC/MC module. I do have serial access (and can see the login prompt in hyperterm). I do have physical access to the FRONT of the chassis (the back of the cabinet is locked and lo-and-behold the key cannot be found). Does anyone know how to reset the password? Every piece of literature I find on the internet tells me I need to log in, or run racadm on the host machine (which I can't, because it's inside a blade chassis). If someone does know how to do it with physical access to the back of the bladecentre, please post it anyway, as I'm sure I'll get access to the back of the cabinet one day)

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• CentOS - massive usage on loopback interface

  - by Matthew Iselin

  Hi, I have a CentOS installation which is running fairly smoothly. Today I ran ifconfig mainly to see what sort of usage has been coming across the ethernet interface, and to also check my link speed. This is what I ended up seeing for the loopback device: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:10301085132061223274 errors:0 dropped:0 overruns:0 frame:0 TX packets:13981054163812689233 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11783901785008000095 (0.6 EiB) TX bytes:10333501021200548281 (0.9 EiB) This just feels completely wrong - almost an EiB of data? Any assistance in tracking down the source of these statistics would be greatly appreciated.

  Read the article

• iptables to allow 80 and 443 on chillispot running ddwrt

  - by user76682

  I am having problems setting this up. this is what I am trying to do. I have Chillispot (hotpsot) running on dd-wrt. Everything is setup, but the client wants only 80 and 443 to go through through the hotspot. I found this tutorial for dd-wrt but that doesnt seem to work. http://www.dd-wrt.com/wiki/index.php/Iptables#Allow_HTTP_traffic_only_to_specific_domain.28s.29 Initially I tried to place the options at the top but didnt work. then i flushed the iptables and set only these three. I can see the pkts number grow but for some reason I can browse. root@DD-WRT:~# iptables -nvL FORWARD Chain FORWARD (policy ACCEPT 3105 packets, 2442K bytes) pkts bytes target prot opt in out source destination 1629 230K ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 multiport dports 21,80,443 2346 2792K ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 328 46420 DROP 0 -- * * 0.0.0.0/0 0.0.0.0/0 Heres some info from the router, chillispot is the tun0 interface. root@DD-WRT:~# iptables -vnL FORWARD --line-numbers Chain FORWARD (policy DROP 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 0 0 ACCEPT 47 -- * vlan1 192.168.8.0/24 0.0.0.0/0 2 0 0 ACCEPT tcp -- * vlan1 192.168.8.0/24 0.0.0.0/0 tcp dpt:1723 3 32 1851 ACCEPT 0 -- tun0 * 0.0.0.0/0 0.0.0.0/0 state NEW 4 0 0 ACCEPT 0 -- br0 br0 0.0.0.0/0 0.0.0.0/0 5 48 2408 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 6 756 452K lan2wan 0 -- * * 0.0.0.0/0 0.0.0.0/0 7 756 452K ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 8 0 0 TRIGGER 0 -- vlan1 br0 0.0.0.0/0 0.0.0.0/0 TRIGGER type:in match:0 relate:0 9 0 0 trigger_out 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 10 0 0 ACCEPT 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 state NEW 11 0 0 DROP 0 -- * * 0.0.0.0/0 0.0.0.0/0 12 0 0 DROP 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 13 0 0 DROP 0 -- * br0 0.0.0.0/0 0.0.0.0/0 The interfaces: root@DD-WRT:~# ifconfig -a br0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F inet addr:192.168.8.1 Bcast:192.168.8.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2371 errors:0 dropped:0 overruns:0 frame:0 TX packets:1862 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:259721 (253.6 KiB) TX bytes:254862 (248.8 KiB) br0:0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:2508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1066410 (1.0 MiB) TX bytes:376001 (367.1 KiB) Interrupt:5 eth1 Link encap:Ethernet HWaddr 00:12:17:CF:80:61 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:729 errors:0 dropped:0 overruns:0 frame:114693 TX packets:697 errors:2 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107869 (105.3 KiB) TX bytes:473134 (462.0 KiB) Interrupt:4 Base address:0x1000 etherip0 Link encap:Ethernet HWaddr 1E:13:B7:09:CC:8C BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:18 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1210 (1.1 KiB) TX bytes:1210 (1.1 KiB) teql0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.182.1 P-t-P:192.168.182.1 Mask:255.255.255.0 UP POINTOPOINT RUNNING MTU:1500 Metric:1 RX packets:662 errors:0 dropped:0 overruns:0 frame:0 TX packets:587 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:92167 (90.0 KiB) TX bytes:427657 (417.6 KiB) vlan0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2371 errors:0 dropped:0 overruns:0 frame:0 TX packets:1864 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:269558 (263.2 KiB) TX bytes:262680 (256.5 KiB) vlan1 Link encap:Ethernet HWaddr 00:12:17:CF:80:60 inet addr:10.3.2.47 Bcast:10.255.255.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2675 errors:0 dropped:0 overruns:0 frame:0 TX packets:645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:705429 (688.8 KiB) TX bytes:102197 (99.8 KiB) The routing table: root@DD-WRT:~# netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.182.0 0.0.0.0 255.255.255.0 U 0 0 0 tun0 10.3.2.0 0.0.0.0 255.255.255.0 U 0 0 0 vlan1 192.168.8.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 10.3.2.1 0.0.0.0 UG 0 0 0 vlan1 Highly appreciate your help. TIA, Arun

  Read the article

• Como instalar Windows (x86/x64) sobre Linux (Ubuntu)

  - by yorrany

  I installed Ubuntu edition (10.04) on my windows 7, completely eliminating it to the original installation. After I was forced to reverse the process, but could not find tools or explanations of how to do it. To clarify the equipment, it is: a netbook, acer, no optical drive cd / dvd, the process should be fully via USB. I hope I was clear enough, count on the support of you. Thank you. -- Instalei a edição Ubuntu (10.04) sobre meu Windows 7, eliminando completamente a a instalação original. Depois fui forçado à reverter o processo, mas não encontrei ferramentas ou explicações de como fazê-lo. Para esclarecer sobre o equipamento, trata-se de: um netbook, acer, sem leitor óptico de cd/dvd, o processo deverá ser totalmente via USB. Espero ter sido bastante claro, conto com o suporte de vocês. Muito obrigado.

  Read the article

• OpenVZ multiple networks on CTs

  - by picca

  I have Hardware Node (HN) which has 2 physical interfaces (eth0, eth1). I'm playing with OpenVZ and want to let my containers (CTs) have access to both of those interfaces. I'm using basic configuration - venet. CTs are fine to access eth0 (public interface). But I can't get CTs to get access to eth1 (private network). I tried: # on HN vzctl set 101 --ipadd 192.168.1.101 --save vzctl enter 101 ping 192.168.1.2 # no response here ifconfig # on CT returns lo (127.0.0.1), venet0 (127.0.0.1), venet0:0 (95.168.xxx.xxx), venet0:1 (192.168.1.101) I believe that the main problem is that all packets flows through eth0 on HN (figured out using tcpdump). So the problem might be in routes on HN. Or is my logic here all wrong? I just need access to both interfaces (networks) on HN from CTs. Nothing complicated.

  Read the article

• udev: waiting for uevents to be processed on my Gentoo

  - by stan31337

  During the startup I see machine executing this thing for about 30 seconds: udev: waiting for uevents to be processed Then I get a quick message which says something like: devfs: timeout (50 seconds) I can't see the whole thing because after that system starts up very fast including Xfce. What logs and configs do I need to provide for further investigation? $uname -a Linux genta 3.6.6-gentoo #1 SMP Sun Nov 11 11:02:23 NOVT 2012 i686 Genuine Intel(R) CPU T2300 @ 1.66GHz GenuineIntel GNU/Linux Thank you! UPD: rc-status genta / # rc-status sysinit Runlevel: sysinit dmesg [ started ] udev [ started ] devfs [ started ] genta / # rc-status boot Runlevel: boot hwclock [ started ] modules [ started ] fsck [ started ] root [ started ] mtab [ started ] localmount [ started ] sysctl [ started ] bootmisc [ started ] hostname [ started ] termencoding [ started ] keymaps [ started ] net.lo [ started ] swap [ started ] urandom [ started ] procfs [ started ]

  Read the article

• openwrt uses a single interface bridge?

  - by timbo

  My understanding of bridging is that it ties together two interfaces at layer 2. I am looking at a Ubiquiti Nanostation2 running OpenWRT that has an ethernet port 'eth0' and a wifi port 'ath0'. The ethernet port (the 'wan' port) is not part of the bridge and the bridge is just a single interface. Can anyone clarify this? - seems very different to Ubuntu. /etc/config/network: config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' config 'interface' 'wifi' option 'ipaddr' '192.168.13.1' option 'type' 'bridge' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ifname' 'wifi0'

  Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >