Search Results

Search found 1236 results on 50 pages for 'nat'.

Page 21/50 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

• iptables advanced routing

  - by Shamanu4

  I have a Centos server acting as a NAT in my network. This server has one external (later ext1) interface and three internal (later int1, int2 and int3). Egress traffic comes from users via int1 and after MASQUERADE goes via ext1. Ingress traffic comes from ext1, MASQUERADE, and goes via int2 or int3 according to static routes. | ext1 | x.x.x.x/24 +---------|----------------------+ | | | Centos server (NAT) | | | +---|------|---------------|-----+ | | | int1 | | int2 | int3 10.30.1.10/24 | | 10.30.2.10/24 | 10.30.3.10/24 ^ v v 10.30.1.1/24 | | 10.30.2.1/24 | 10.30.3.1/24 +---|------|---------------|-----+ | | | | | | | v v | | ^ -Traffic policer- | | |_____________ | | | | | +------------------|-------------+ | 192.168.0.1/16 | | Clients 192.168.0.0/16 The problem: Egress traffic seems to be dropped after PREROUTING table. Packet counters are not changing on MASQUERADE rule in POSTROUTING. If I change the routes to clients causing the traffic go back via int1 - everything works perfectly. current iptable configuration is very simple: # cat /etc/sysconfig/iptables *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -I INPUT 1 -i int1 -j ACCEPT -A FORWARD -j ACCEPT COMMIT *nat -A POSTROUTING -o ext1 -j MASQUERADE # COMMIT Can anyone point me what I'm missing? Thanks. UPDATE: 192.168.100.60 via 10.30.2.1 dev int2 proto zebra # routes to clients ... 192.168.100.61 via 10.30.3.1 dev int3 proto zebra # ... I have a lot of them x.x.x.0/24 dev ext1 proto kernel scope link src x.x.x.x 10.30.1.0/24 dev int1 proto kernel scope link src 10.30.1.10 10.30.2.0/24 dev int2 proto kernel scope link src 10.30.2.10 10.30.3.0/24 dev int3 proto kernel scope link src 10.30.3.10 169.254.0.0/16 dev ext1 scope link metric 1003 169.254.0.0/16 dev int1 scope link metric 1004 169.254.0.0/16 dev int2 scope link metric 1005 169.254.0.0/16 dev int3 scope link metric 1006 blackhole 192.168.0.0/16 default via x.x.x.y dev ext1 Clients have 192.168.0.1 as gateway, which is redirecting them to 10.30.1.1

  Read the article

• iptables secure squid proxy

  - by Lytithwyn

  I have a setup where my incoming internet connection feeds into a squid proxy/caching server, and from there into my local wireless router. On the wan side of the proxy server, I have eth0 with address 208.78.∗∗∗.∗∗∗ On the lan side of the proxy server, I have eth1 with address 192.168.2.1 Traffic from my lan gets forwarded through the proxy transparently to the internet via the following rules. Note that traffic from the squid server itself is also routed through the proxy/cache, and this is on purpose: # iptables forwarding iptables -A FORWARD -i eth1 -o eth0 -s 192.168.2.0/24 -m state --state NEW -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE # iptables for squid transparent proxy iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j DNAT --to 192.168.2.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 80 -j REDIRECT --to-port 3128 How can I set up iptables to block any connections made to my server from the outside, while not blocking anything initiated from the inside? I have tried doing: iptables -A INPUT -i eth0 -s 192.168.2.0/24 -j ACCEPT iptables -A INPUT -i eth0 -j REJECT But this blocks everything. I have also tried reversing the order of those commands in case I got that part wrong, but that didn't help. I guess I don't fully understand everything about iptables. Any ideas?

  Read the article

• Problem routing between directly connected Subnets w/ ASA-5510

  - by Zephyr Pellerin

  This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

  Read the article

• One dns server in different subnets

  - by hofmeister

  I have installed a small Linux server; the server is in a different subnet as the internet hosts. I added a route to my nat router to create a connection between both subnets. In both subnets I use an extra dhcp Server. Subnet A: 192.168.0.0/26 Subnet B: 192.168.1.0/26 Router: 192.168.0.1, Server in A: 192.168.0.62, Server in B: 192.168.1.62 internet ____ nat router ___ (Sub A)___ internet hosts | |____(Sub B)___ other hosts I could ping every host. Also the hosts which are connected to the subnet b, has internet connection. But sadly I have a problem with the dns server. I use the dnsServer from my nat router, I set the dns Server for subnet b to the ip 192.168.0.1, but every dns entries are equal with the hostname from my linux server. Example if the hostname from the server is test Test 192.168.0.62 //Server subnet a Test-2 192.168.1.62 //Server subnet b Test-2-2 192.168.1.1 //host a Test-2-2-2 192.168.1.2 //host b Any idea what went wrong? The internet dns resolution works fine.

  Read the article

• iptables port redirection on Ubuntu

  - by Xi.

  I have an apache server running on 8100. When open http://localhost:8100 in browser we will see the site running correctly. Now I would like to direct all request on 80 to 8100 so that the site can be accessed without the port number. I am not familiar with iptables so I searched for solutions online. This is one of the methods that I have tried: user@ubuntu:~$ sudo iptables -A INPUT -p tcp --dport 80 -j ACCEPT user@ubuntu:~$ sudo iptables -A INPUT -p tcp --dport 8100 -j ACCEPT user@ubuntu:~$ sudo iptables -t nat -A PREROUTING -p tcp --dport 80 -j REDIRECT --to-ports 8100 It's not working. The site works on 8100 but it's not on 80. If print out the rules using "iptables -t nat -L -n -v", this is what I see: user@ubuntu:~$ sudo iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 14 packets, 2142 bytes) pkts bytes target prot opt in out source destination 0 0 REDIRECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 redir ports 8100 Chain INPUT (policy ACCEPT 14 packets, 2142 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 177 packets, 13171 bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 177 packets, 13171 bytes) pkts bytes target prot opt in out source destination The OS is a Ubuntu on a VMware. I thought this should be a simple task but I have been working on it for hours without success. :( What am I missing?

  Read the article

• Iptables - forward email ports?

  - by Emmet Brown

  im trying to open some local ports (LAN) and then re-direct them to another server (WAN) using iptables. Here is my config: #WAN allow-hotplug eth1 auto eth1 iface eth1 inet static #Tarjeta red WAN address 192.168.2.2 gateway 192.168.2.1 netmask 255.255.255.0 #LAN allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.16.6 netmask 255.255.255.0 network 192.168.16.0 broadcast 192.168.16.255 I try this: iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 110 -j DNAT --to 200.40.30.218:110 iptables -A FORWARD -p tcp -i eth0 -o eth1 -d 200.40.30.218 --dport 110 -j ACCEPT iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 25 -j DNAT --to 200.40.30.218:25 iptables -A FORWARD -p tcp -i eth0 -o ethq -d 200.40.30.218 --dport 25 -j ACCEPT but, it did not work. i also try changeing eth0 to eth1 (and eth1 to eth0) but nothing happened. Starting Nmap 5.00 ( http://nmap.org ) at 2011-10-03 14:44 UYST Interesting ports on 192.168.16.6: Not shown: 997 closed ports PORT STATE SERVICE 22/tcp open ssh 111/tcp open rpcbind 8080/tcp open http-proxy Im running debian. Can u guys help me to check what is happening? edit: IPTABLES-SAVE # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *mangle :PREROUTING ACCEPT [139993:77867651] :INPUT ACCEPT [139385:77761761] :FORWARD ACCEPT [186:12071] :OUTPUT ACCEPT [173556:74341650] :POSTROUTING ACCEPT [173734:74352988] COMMIT # Completed on Mon Oct 3 15:43:14 2011 # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *nat :PREROUTING ACCEPT [1649:190626] :POSTROUTING ACCEPT [6729:339646] :OUTPUT ACCEPT [6697:337660] -A PREROUTING -i eth0 -p tcp -m tcp --dport 110 -j DNAT --to-destination 200.40.30.218:110 -A PREROUTING -i eth0 -p tcp -m tcp --dport 25 -j DNAT --to-destination 200.40.30.218:25 COMMIT # Completed on Mon Oct 3 15:43:14 2011 # Generated by iptables-save v1.4.8 on Mon Oct 3 15:43:14 2011 *filter :INPUT ACCEPT [138307:77066136] :FORWARD ACCEPT [168:11207] :OUTPUT ACCEPT [172288:73655708] -A FORWARD -d 200.40.30.218/32 -i eth0 -o eth1 -p tcp -m tcp --dport 110 -j ACCEPT -A FORWARD -d 200.40.30.218/32 -i eth0 -o ethq -p tcp -m tcp --dport 25 -j ACCEPT COMMIT # Completed on Mon Oct 3 15:43:14 2011 Regards

  Read the article

• Redirect traffic from 127.0.0.1 to 127.0.0.1 on port 53 to port 5300 with iptables

  - by Zagorax

  I'm running a local dns server on port 5300 to develop a software. I need my machine to use that dns but I wasn't able to tell /etc/resolv.conf to check on a different port. I searched a bit on google and I didn't find a solution. I set 127.0.0.1 as nameserver on /etc/resolv.conf. This is my whole /etc/resolv.conf: nameserver 127.0.0.1 Could you please tell me how can I redirect outbound traffic on port 53 to another port? I tried the following but it didn't work: iptables -t nat -A PREROUTING -p tcp --dport 53 -j DNAT --to 127.0.0.1:5300 iptables -t nat -A PREROUTING -p udp --dport 53 -j DNAT --to 127.0.0.1:5300 Here is the output of iptables -t nat -L -v -n (with suggested rules): Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 REDIRECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:53 redir ports 5300 0 0 REDIRECT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:53 redir ports 5300 Chain POSTROUTING (policy ACCEPT 302 packets, 19213 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 302 packets, 19213 bytes) pkts bytes target prot opt in out source destination

  Read the article

• WCF port routing

  - by C james

  I have NAT which received incoming WCF requests and changes port number before it hands off to the host however, this is causing problem is there anyway to turn this off or fix? ex) wcf.service.com:80 - NAT - wcf.service.2522 !error Thank you.

  Read the article

• Configuring Wireless on Cisco 851W

  - by Aequitarum Custos

  Either a powersurge or something caused our router's configuration to get wiped, and our last backup was before the wireless network was setup. We have not been able to reconfigure the wireless since then, so was curious if anyone here would be able to determine what configuration is needed. We are using a Cisco 851W running 12.4(15)T9 We would like to use WPA encryption, and have it on the same network as the rest of the office network. Config file is below: User Access Verification Building configuration... Current configuration : 3857 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption no service dhcp ! hostname BOB ! boot-start-marker boot-end-marker ! enable secret 5 ********************* ! no aaa new-model ! ! dot11 syslog no ip source-route ! ! ip cef no ip bootp server ip domain name BOB.com ip name-server 61.11.1.1 ip name-server 61.11.1.2 ! ! ! username BOBB privilege 15 password 7 ************************* ! ! archive log config hidekeys ! ! ip tcp synwait-time 10 ! ! ! interface FastEthernet0 no cdp enable ! interface FastEthernet1 no cdp enable ! interface FastEthernet2 no cdp enable ! interface FastEthernet3 no cdp enable ! interface FastEthernet4 description WAN Connection$ETH-WAN$ ip address 61.11.1.14 255.255.254.0 ip nat outside ip virtual-reassembly duplex auto speed auto no cdp enable ! interface Dot11Radio0 no ip address shutdown ! encryption mode ciphers tkip speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root no cdp enable ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no cdp enable bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio0.20 ip access-group Guest-ACL in no cdp enable ! interface Vlan1 description Internal Network ip address 192.168.2.60 255.255.255.0 ip nat inside ip nat enable ip virtual-reassembly ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 61.11.2.14 ! ip http server no ip http secure-server ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended Guest-ACL deny ip any 192.0.0.0 0.0.0.255 permit ip any any ! access-list 1 permit 192.0.0.0 0.0.0.255 access-list 100 remark SDM_ACL Category=2 access-list 100 permit ip 192.0.0.0 0.0.0.255 any no cdp run ! control-plane ! !

  Read the article

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• Sonicwall VPN, Domain Controller Issues

  - by durilai

  I am trying to get the domain logon script to execute when I connect to VPN. I have a SonicWall 4060PRO, with the SonicOS Enhanced 4.2.0.0-10e. The VPN connects successfully, but the script does not execute. I am posting the log below, but I see two issues. The first is the inability to connect to domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. The second is the failure of the script. 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found.. I assume the second issue is caused because of the first, also on the second issue it seems to be trying to get the logon script from my local PC, not the server. Finally, the DC can be pinged and reached by its computer name once the VPN is connected. The shares that the script is tring to map can be mapped manually. Any help is appreciated. 2009/12/18 19:49:31:063 Information The connection "GroupVPN_0006B1030980" has been enabled. 2009/12/18 19:49:32:223 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX XAuth has requested a username but one has not yet been specified. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Sending phase 1 delete. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX User authentication information is needed to complete the connection. 2009/12/18 19:49:32:393 Information An incoming ISAKMP packet from XXX.XXX.XXX.XXX was ignored. 2009/12/18 19:49:36:962 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:37:094 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:37:100 Information XXX.XXX.XXX.XXX Sending XAuth reply. 2009/12/18 19:49:37:110 Information XXX.XXX.XXX.XXX Received initial contact notify. 2009/12/18 19:49:37:153 Information XXX.XXX.XXX.XXX Received XAuth status. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX Sending XAuth acknowledgement. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX User authentication has succeeded. 2009/12/18 19:49:37:247 Information XXX.XXX.XXX.XXX Received request for policy version. 2009/12/18 19:49:37:253 Information XXX.XXX.XXX.XXX Sending policy version reply. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Received policy change is not required. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Sending policy acknowledgement. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX The configuration for the connection is up to date. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 2 negotiation with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting quick mode phase 2 exchange. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX The SA lifetime for phase 2 is 28800 seconds. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX Phase 2 with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP has completed. 2009/12/18 19:49:37:896 Information Renewing IP address for the virtual interface (00-60-73-4C-3F-45). 2009/12/18 19:49:40:189 Information The virtual interface has been added to the system with IP address 10.10.10.112. 2009/12/18 19:49:40:319 Information The system ARP cache has been flushed. 2009/12/18 19:49:40:576 Information XXX.XXX.XXX.XXX NetWkstaUserGetInfo returned: user: Dustin, logon domain: DT-WIN7, logon server: DT-WIN7 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX calling NetUserGetInfo: Server: , User: Dustin, level: 3 2009/12/18 19:49:53:460 Information XXX.XXX.XXX.XXX NetUserGetInfo returned: home dir: , remote dir: , logon script: 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found..

  Read the article

• Cisco 891w multiple VLAN configuration

  - by Jessica

  I'm having trouble getting my guest network up. I have VLAN 1 that contains all our network resources (servers, desktops, printers, etc). I have the wireless configured to use VLAN1 but authenticate with wpa2 enterprise. The guest network I just wanted to be open or configured with a simple WPA2 personal password on it's own VLAN2. I've looked at tons of documentation and it should be working but I can't even authenticate on the guest network! I've posted this on cisco's support forum a week ago but no one has really responded. I could really use some help. So if anyone could take a look at the configurations I posted and steer me in the right direction I would be extremely grateful. Thank you! version 15.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESI ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings ! aaa new-model ! ! aaa authentication login userauthen local aaa authorization network groupauthor local ! ! ! ! ! aaa session-id common ! ! ! clock timezone EST -5 clock summer-time EDT recurring service-module wlan-ap 0 bootimage autonomous ! crypto pki trustpoint TP-self-signed-3369945891 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3369945891 revocation-check none rsakeypair TP-self-signed-3369945891 ! ! crypto pki certificate chain TP-self-signed-3369945891 certificate self-signed 01 (cert is here) quit ip source-route ! ! ip dhcp excluded-address 192.168.1.1 ip dhcp excluded-address 192.168.1.5 ip dhcp excluded-address 192.168.1.2 ip dhcp excluded-address 192.168.1.200 192.168.1.210 ip dhcp excluded-address 192.168.1.6 ip dhcp excluded-address 192.168.1.8 ip dhcp excluded-address 192.168.3.1 ! ip dhcp pool ccp-pool import all network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 10.171.12.5 10.171.12.37 lease 0 2 ! ip dhcp pool guest import all network 192.168.3.0 255.255.255.0 default-router 192.168.3.1 dns-server 10.171.12.5 10.171.12.37 ! ! ip cef no ip domain lookup no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO891W-AGN-A-K9 sn FTX153085WL ! ! username ESIadmin privilege 15 secret 5 $1$g1..$JSZ0qxljZAgJJIk/anDu51 username user1 password 0 pass ! ! ! class-map type inspect match-any ccp-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-all ccp-insp-traffic match class-map ccp-cls-insp-traffic class-map type inspect match-any ccp-cls-icmp-access match protocol icmp class-map type inspect match-all ccp-invalid-src match access-group 100 class-map type inspect match-all ccp-icmp-access match class-map ccp-cls-icmp-access class-map type inspect match-all ccp-protocol-http match protocol http ! ! policy-map type inspect ccp-permit-icmpreply class type inspect ccp-icmp-access inspect class class-default pass policy-map type inspect ccp-inspect class type inspect ccp-invalid-src drop log class type inspect ccp-protocol-http inspect class type inspect ccp-insp-traffic inspect class class-default drop policy-map type inspect ccp-permit class class-default drop ! zone security out-zone zone security in-zone zone-pair security ccp-zp-self-out source self destination out-zone service-policy type inspect ccp-permit-icmpreply zone-pair security ccp-zp-in-out source in-zone destination out-zone service-policy type inspect ccp-inspect zone-pair security ccp-zp-out-self source out-zone destination self service-policy type inspect ccp-permit ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group 3000client key 67Nif8LLmqP_ dns 10.171.12.37 10.171.12.5 pool dynpool acl 101 ! ! crypto ipsec transform-set myset esp-3des esp-sha-hmac ! crypto dynamic-map dynmap 10 set transform-set myset ! ! crypto map clientmap client authentication list userauthen crypto map clientmap isakmp authorization list groupauthor crypto map clientmap client configuration address initiate crypto map clientmap client configuration address respond crypto map clientmap 10 ipsec-isakmp dynamic dynmap ! ! ! ! ! interface FastEthernet0 ! ! interface FastEthernet1 ! ! interface FastEthernet2 ! ! interface FastEthernet3 ! ! interface FastEthernet4 ! ! interface FastEthernet5 ! ! interface FastEthernet6 ! ! interface FastEthernet7 ! ! interface FastEthernet8 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! ! interface GigabitEthernet0 description $FW_OUTSIDE$$ES_WAN$ ip address 10...* 255.255.254.0 ip nat outside ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto map clientmap ! ! interface wlan-ap0 description Service module interface to manage the embedded AP ip unnumbered Vlan1 arp timeout 0 ! ! interface Wlan-GigabitEthernet0 description Internal switch interface connecting to the embedded AP switchport trunk allowed vlan 1-3,1002-1005 switchport mode trunk ! ! interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-FE 1$$FW_INSIDE$ ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly zone-member security in-zone ip tcp adjust-mss 1452 crypto map clientmap ! ! interface Vlan2 description guest ip address 192.168.3.1 255.255.255.0 ip access-group 120 in ip nat inside ip virtual-reassembly zone-member security in-zone ! ! interface Async1 no ip address encapsulation slip ! ! ip local pool dynpool 192.168.1.200 192.168.1.210 ip forward-protocol nd ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! ip dns server ip nat inside source list 23 interface GigabitEthernet0 overload ip route 0.0.0.0 0.0.0.0 10.165.0.1 ! access-list 23 permit 192.168.1.0 0.0.0.255 access-list 100 remark CCP_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 10.165.0.0 0.0.1.255 any access-list 110 permit ip 192.168.0.0 0.0.5.255 any access-list 120 remark ESIGuest Restriction no cdp run ! ! ! ! ! ! control-plane ! ! alias exec dot11radio service-module wlan-ap 0 session Access point version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESIRouter ! no logging console enable secret 5 $1$yEH5$CxI5.9ypCBa6kXrUnSuvp1 ! aaa new-model ! ! aaa group server radius rad_eap server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa group server radius rad_acct server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa authentication login eap_methods group rad_eap aaa authentication enable default line enable aaa authorization exec default local aaa authorization commands 15 default local aaa accounting network acct_methods start-stop group rad_acct ! aaa session-id common clock timezone EST -5 clock summer-time EDT recurring ip domain name ESI ! ! dot11 syslog dot11 vlan-name one vlan 1 dot11 vlan-name two vlan 2 ! dot11 ssid one vlan 1 authentication open eap eap_methods authentication network-eap eap_methods authentication key-management wpa version 2 accounting rad_acct ! dot11 ssid two vlan 2 authentication open guest-mode ! dot11 network-map ! ! username ESIadmin privilege 15 secret 5 $1$p02C$WVHr5yKtRtQxuFxPU8NOx. ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! ssid two ! antenna gain 0 station-role root ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 bridge-group 2 subscriber-loop-control bridge-group 2 block-unknown-source no bridge-group 2 source-learning no bridge-group 2 unicast-flooding bridge-group 2 spanning-disabled ! interface Dot11Radio1 no ip address no ip route-cache shutdown ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! antenna gain 0 dfs band 3 block channel dfs station-role root ! interface Dot11Radio1.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache ! interface GigabitEthernet0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface GigabitEthernet0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 no bridge-group 2 source-learning bridge-group 2 spanning-disabled ! interface BVI1 ip address 192.168.1.2 255.255.255.0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag access-list 10 permit 192.168.1.0 0.0.0.255 radius-server host 192.168.1.5 auth-port 1812 acct-port 1813 key ***** bridge 1 route ip

  Read the article

• PortForwarding to IIS in Linux

  - by Simon

  Hi, I am trying to set up port forwarding on a linux box to a IIS webserver on my internal network. The web server sits on Windows 2003 Server. My linux box has eth0 - Internet connection eth1 - internal subnet (10.10.10.x) eth2 - 2nd internal subnet (129.168.0.x) dhcp interface my webserver is on the eth2 interface (192.168.0.6) I am doing port forwarding for port 80 with no avail. I use the same set of rules to port forward to a different webserver and it works. The webapplication is available on the internal network but not for external users. iptables -t nat -A PREROUTING -p tcp -i eth0 -d $PUBLIC_IP --dport 80 -j DNAT --to 192.168.0.6:80 iptables -A FORWARD -p tcp -i eth0 -o eth2 -d 192.168.0.6 --dport 80 -m state --state NEW -j ACCEPT iptables -A FORWARD -t filter -o eth0 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -t filter -i eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE Any Ideas?

  Read the article

• OpenVPN access server on Amazon VPC vs free version

  - by imaginative

  Maybe I'm missing the point, but I'd like to setup simple VPN access with software VPN to access my private network on Amazon VPC. I thought OpenVPN would be a great solution for this, and I thought it might make sense to put this on the NAT instance that comes with VPC so I don't have to spend money on another instance. Is there any advantage to running the following: http://www.openvpn.net/index.php?option=com_content&id=493 vs sticking to the free solution of OpenVPN? What does one offer over the other? Any reason not to run this on the NAT instance itself?

  Read the article

• Home network with Windows 7 as router

  - by Michael

  Background: I have tried to use routers, but so far all of them can't handle the bandwidth, number of connections eventually limited by the hardware resources, so overall the home routers are decreasing the internet speed. I went through DD-WRT and stuff like that. Question: What I want is to use my Windows7 PC as router. It has 2 LAN cards. I'm going to connect to this router another desktop 2 pcs and notebook through wireless router. The main question is what is the most efficient way to turn this Windows7 box(and I need Windows for native NTFS support) into router with NAT/Routing/Firewall functionality? Is there any routing software recommended for this purpose or I should just use windows native "Internet Sharing"? I'm going to run SIP phones in the LAN, so I need friendly NAT(Full cone perhaps). Also I'm going to have FTP server on that Windows7 "server" PC. As firewall I'm thinking about Comodo. Need to drop all incoming, unless explicitly allowed.

  Read the article

• Rerouting traffic from port 80 to another port on a single ip

  - by zam

  I have a server with multiple IP addresses associated with it. I'm trying to run a node.js web server (which I do not want to run as root), using only one of those ip addresses (it would be very bad if the traffic from all the ip addresses were forwarded). Through searching superuser, it looked like this could be possible with iptables: How to setting up iptables for traffic fowarding on port 80 from specific sources iptables -A PREROUTING -t nat -i eth0 -p tcp --dport 80 --source 212.333.111.222 -j REDIRECT --to-port 9020 However, I do not understand why eth0 is needed. According to: http://blog.softlayer.com/2011/iptables-tips-and-tricks-port-redirection/ this could be done with: iptables -t nat -A PREROUTING -p tcp --dport 2525 -j REDIRECT --to-ports 25 What is the correct way of forwarding traffic from a single ip on port 80, lets say 111.111.111.111:80 to another port on the same server, lets say 111.111.111.111:8765? thanks for your help!

  Read the article

• Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

  - by Sise

  Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

  Read the article

• Server with 3 public IP and iptables

  - by Juan

  I have a linux box with two NIC cards: eth0 and eth1. In one card i have 3 public IP: eth0 = 10.10.10.1, eth0:1= 10.10.10.2 and eth0:2= 10.10.10.3 In the other card i have one local IP eth1 = 192.9.200.1 I want to redirect all the wan traffic for 10.10.10.2 to the LAN 192.9.200.2 and the same for 10.10.10.3 to 192.9.200.3 I have tried with this rule but doesn't work iptables -t nat -A PREROUTING -i eth0 -d 10.10.10.2 -j DNAT --to-destination 192.9.200.2 iptables -t nat -A PREROUTING -i eth0 -d 10.10.10.3 -j DNAT --to-destination 192.9.200.3 IP forward is enabled in /etc/sysctl.conf Can you help me, please.

  Read the article

• Layer 3 switch routing

  - by Yoshiwaan

  I need help moving over to using our layer 3 switch as the inter vlan routing device rather than our cisco router. I've mostly got it working but I've got stuck near the end and need some advice (I think I just need a bit of education on the subject really). Cur I have a Dell PowerConnect 7048 connecting to a Cisco 1841 router. I've got a few key excerpts from the configs to provide the key information. On the powerconnect I have the following: ip routing ip default-gateway 172.31.14.1 ip route 0.0.0.0 0.0.0.0 172.31.14.1 253 ! interface vlan 1 ip address 172.31.14.254 255.255.255.0 exit interface vlan 2 ip address 172.31.19.254 255.255.255.0 exit interface vlan 4 ip address 172.31.16.254 255.255.255.0 ! interface Gi1/0/1 description 'Link to L7Router01' switchport mode trunk switchport trunk allowed vlan except 3,7-4093 exit ! and on the Cisco the following: interface FastEthernet0/0 ip address 172.31.14.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.2 description Accounts VLAN encapsulation dot1Q 2 ip address 172.31.19.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.4 description Voice VLAN encapsulation dot1Q 4 ip address 172.31.16.1 255.255.255.0 ip nat inside ip virtual-reassembly ! So what I'm doing is moving clients over so that their default gateway is a 172.31.x.254 address rather than a 172.31.x.1 address. This works great for inter-vlan routing, I have no issues with this. The switch can also access the router no worries, and users on the 172.31.14.0/24 network can access all interfaces and sub-interfaces on the router, including 172.31.14.1. They can also access all of the interfaces that the router connects off to, no worries there. The problem I have is that users on the 172.31.16.0/24 and 172.31.19.0/24 subnets cannot access either 172.31.14.1 or any of the subnets the router connects to. They can, however, connect to BOTH of the sub interfaces on the router from either subnet. What am I missing here? Why can't the vlans connect to the non-sub interface on the router? Are tagged packets being sent to this interface?

  Read the article

• Internet connection sharing: Ubuntu 9.10 Server on Windows 7 and VMWare

  - by avesse

  I'm trying to get Internet Connection Sharing (ICS) working between my Windows 7 RTM host and a Ubuntu 9.10 Server running on VMWare Workstation 6.5, but I have not been able to get it right. Here's what I have done: Configured VMWare to use Host Only networking (I tried NAT as well). Enabled ICS on my host's network connection, allowing VMnet1. After enabling it, Windows informed me that its VMnet1 IP has changed to 192.168.137.1. So in VMWare's Virtual Network Editor I configured VMnet1: Subnet 192.168.137.0 Mask 255.255.255.0 I did the same for DHCP. For NAT i set 192.168.137.1 as Gateway. I cannot ping any sites or get access through apt-get/aptitude install/update, although domains do get resolved to IPs. I have also tried using a static IP in Ubuntu. I don't know if it makes a difference, but my external IP is locked to my host's MAC address.

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• configure cisco catalyst 3560g with an egress uplink

  - by imaginative

  Currently my setup has our egress uplink connected directly to an external interface on a linux router/firewall/nat gateway. Since the linux box is a single point of failure, I've since setup two openbsd boxes using carp+pf+pfsync in order to gain some additional redundancy. the problem is, I only have one egress uplink (it's still a single point of failure) but need to get it to speak to the active carp node in my openbsd cluster which will server as my new router/firewall/nat cluster. Is there anything specific I need to do on a 3560G in order for me to be able to: 1) Drop the egress uplink into a port 2) Drop one link from the switch to a firewall 2) Drop a second link from a switch to the firewall This is so if one box dies, the other still has the egress link to the switch. Is putting them into one VLAN enough? Anything else that needs to go into the configuration for this setup to work?

  Read the article

• iptables port forwarding troubleshooting

  - by cbmanica

  I'm trying to forward connections on port 18600 to port 9980. I have this in /etc/sysconfig/iptables: # Generated by iptables-save v1.3.5 on Mon Oct 21 18:30:43 2013 *nat :PREROUTING ACCEPT [2:280] :POSTROUTING ACCEPT [12:768] :OUTPUT ACCEPT [12:768] -A PREROUTING -p tcp -m tcp --dport 18600 -j REDIRECT --to-ports 9980 COMMIT # Completed on Mon Oct 21 18:30:43 2013 and /etc/init.d/iptables status shows me this: Table: nat Chain PREROUTING (policy ACCEPT) num target prot opt source destination 1 REDIRECT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:18600 redir ports 9980 However, I can telnet from localhost to port 9980, but not 18600. What am I missing? (This is a CentOS-based VM.)

  Read the article

• 2 routers, both DHCP, no IP assigned

  - by piobyz

  I can't get DHCP to assign IP to my wireless devices. My network config is as follows: Nanostation5 Linksys WRT350N, which is connected with Nanostation via its INTERNET port. Nanostation: LAN IP Address: 192.168.1.20 WLAN IP Address: 192.168.0.79 Network Mode: Router and is getting its IP via DHCP from my ISP Netmask: 255.255.255.0 Gateway IP: 192.168.1.1 LAN Network settings: IP Address: 192.168.1.20 Netmask: 255.255.255.0 Enable NAT: YES ENABLE DHCP Server: YES Range 192.168.1.100 ~ 250 Netmask: 255.255.255.0 Enable DNS Proxy: YES Linksys: Internet Connection Type: DHCP Router IP: 192.168.2.1 Subnet Mask: 255.255.255.0 DHCP: Enabled Start IP: 192.168.2.100 ~ 120 Advanced Routing: NAT: Enabled What I can do is connecting manually with this config: IP: 192.168.2.101 Subnet Mask: 255.255.255.0 Router: 192.168.2.1 DNS: 192.168.1.20 Search domains: WRT350N I want to be able to connect to both routers independently(now its 192.168.1.20 for Nanostation, and 192.168.2.1 for Linksys) and connect any wireless device using DHCP. What should be IP ranges, masks, etc. on both devices?

  Read the article

• Asterisk: Forcing a sip peer to connect via ipv6?

  - by growse

  I've got an asterisk server that connects to an upstream provider over a WAN. The upstream provider supports both IPv4 and IPv6 connectivity, and the asterisk server is behind a NAT. When asterisk connects to the upstream sip peer via IPv6, everything works perfectly. The issue I have is that when I configure the asterisk server IPv6 address via DHCPv6, a race condition means that asterisk sometimes ends up attempting to contact the upstream peer via IPv4 (the SIP DNS name has both A and AAAA records). This is because asterisk starts up before the system has a valid IPv6 address. The connection does not work via IPv4 because of the NAT. Is there a way of configuring the peer to specify that it should only be contactable over IPv6? I guess it might be possible to hack together a firewall rule to deny all IPv4 traffic to that IP, but it'd be easier to configure this within asterisk itself.

  Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >