Search Results

Search found 7061 results on 283 pages for 'target'.

Page 211/283 | < Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• port forwarding problem

  - by Claudiu

  I want to set up an svn server on my computer, so it's available from anywhere. I think I set up the repository correctly, using CollabSVN. If I go to Repo-Browser with TortoiseSVN and point it to svn://localhost:3690, it shows the proper repository. The problem now is that I'm behind a router. My local IP is 192.168.1.45 . Doing svn://192.168.1.45:3690 also works. My global IP is, say, x.x.x.x. Just doing svn://x.x.x.x:3690 doesn't work, which makes sense, since I have to set up port forwarding. I'm using a Verizon router. Using their web interface (on 192.168.1.1) I added the following port forwarding rule: IP Address forward to: 192.168.1.45 Source Ports: Any Dest Ports: 3690 Forward to: 3690 Protocol: TCP However, even after applying this rule, going to svn://x.x.x.x:3690 doesn't work. It takes a few seconds to fail, then says that the connection couldn't be established because the server connected to didn't respond properly after a period of time. What's interesting is that a random port, like svn://x.x.x.x:36904 fails immediately, saying that the target machine actively refused the connection. So I figure that the forwarding rule did something, but not fully what was necessary. Any ideas on how to get this working? The router model is MI424-WR and the firmware version is 4.0.16.1.56.0.10.12.3. UPDATE: I also tried setting destination port to 45000, and still forwarding to 3690, in case something was wrong w/ the lower-numbered ports, but to no avail. I also tried port 80 to port 3690, still all in vain.

  Read the article

• Node js server not responding outside localhost centos

  - by David Martinez

  I'm running a basic express server from CentOS but for some reason it is not responding outside of localhost, I have tried everything I have found on google but nothing works so far. This is my express server: app.listen(3000,"0.0.0.0"); If I do curl http://localhost:3000/ in the server it works fine. If I curl to the ip of the server it doesn't work. I already changed my iptables num target prot opt source destination 1 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 2 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 3 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:3000 There is currently a apache server running on port 80 with no problems. I also tried setting a VirtualHost on apache but it didn't work either: <VirtualHost *:80> ServerName SubDOmain.MyDomain.com ProxyRequests off <Proxy *> Order allow,deny Allow from all </Proxy> ProxyPass / http://localhost:3000/ ProxyPassReverse / http://localhost:3000/ ProxyPreserveHost on </VirtualHost> There is another virtual host working fine that redirects to another DocumentRoot. I'm running Node on root for testing purpose, but the node application owner is another user. All folders have 705 and files 664 Edit: I stopped apache and run my node app on port 80 and it working fine, I could access node app from my ip and domain.

  Read the article

• Time-Machine backup over SSH tunnel to NFS mount

  - by BTZ

  I've recently started using a new NAS which runs CentOS 6.2. One of the purposes of the NAS would be to serve as a backup target. Whilst I have been using Apple's Time-Machine for a while and I am very satisfied with it, I'd like to continue using it. Backing up directly to an address in my network is no hassle; all works fine. For security reasons I'd like all my traffic to go through an ssh tunnel to the NAS. This way I can avoid needing to get a VPNserver (for personal reasons). As of NFSv4 the NFS deamon is bound to port 2049, which makes it easy for me to direct all traffic through a ssh tunnel. Tunnel: ssh -f admin@ms -L 2000:localhost:2049 -N Mount: mount -t nfs -o nfsvers=4,rw,proto=tcp,sync,intr,hard,timeo=600,retrans=10,wsize=32768,rsize=32768,port=2000 localhost:/mac_backup /Volumes/backup This works fine for Finder/terminal and throughput is almost equal to direct traffic. (CPU of the NAS does ride high when I reach max bandwidth though) Now the problem: With Time-Machine I can't use the NFS mount point mounted on localhost. TM seems to try to connect to it and then give me a "OSStatus error 65". I also tried using NFSv3 (I correctly forwarded all ports) with no luck. Can anyone shed a light on this and/or give a solution?

  Read the article

• MacOS creates a new mount on AFP path calls

  - by jAndy

  Hi Folks, following scenario: In my webapp, my customers are using Firefox as target browser. They have the need to open afp:// folders via Javascript. To make a long story short, this really works. You need to setup Firefox with about:config and set the value network.protocol-handler.external.afp to true. What happens then, the operating system (OSX) takes care of that path and it correctly opens a Finder window. The problem: OSX does create a new mount every time. It cannot distinct between afp://host/path/111 and afp://host/path/222 for instance. Furthermore, even if the afp path is 100% identical a new mount is created. It looks like this is the default behavior from OSX regardless of Firefox. So, is there any chance I can tell OSX not to create a new mount for some sub directorys which should get access over afp:// ? update: It looks like, there are OSX applications which can change the default behavior for network protocols. So you can change "somewhere" which application OSX should call for a protocol. If that is true, wouldn't it be possible to create a script which just opens the local path without a afp:// prefix ? The question here is, where is that configuration (?) to tell OSX which application to use for specific protocol. Any help welcome!

  Read the article

• Mechanism behind user forwarding in ScriptAliasMatch

  - by jolivier

  I am following this tutorial to setup gitolite and at some point the following ScriptAliasMatch is used: ScriptAliasMatch \ "(?x)^/(.*/(HEAD | \ info/refs | \ objects/(info/[^/]+ | \ [0-9a-f]{2}/[0-9a-f]{38} | \ pack/pack-[0-9a-f]{40}\.(pack|idx)) | \ git-(upload|receive)-pack))$" \ /var/www/bin/gitolite-suexec-wrapper.sh/$1 And the target script starts with USER=$1 So I am guessing this is used to forward the user name from apache to the suexec script (which indeed requires it). But I cannot see how this is done. The ScriptAliasMatch documentation makes me think that the /$1 will be replaced by the first matching group of the regexp before it. For me it captures from (?x)^/(.* to ))$ so there is nothing about a user here. My underlying problem is that USER is empty in my script so I get no authorizations in gitolite. I give my username to apache via a basic authentication: <Location /> # Crowd auth AuthType Basic AuthName "Git repositories" ... Require valid-user </Location> defined just under the previous ScriptAliasMatch. So I am really wondering how this is supposed to work and what part of the mechanism I missed so that I don't retrieve the user in my script.

  Read the article

• How to test a HTTPS URL with a given IP address

  - by GreatFire

  Let's say a website is load-balanced between several servers. I want to run a command to test whether it's working, such as curl DOMAIN.TLD. So, to isolate each IP address, I specify the IP manually. But many websites may be hosted on the server, so I still provide a host header, like this: curl IP_ADDRESS -H 'Host: DOMAIN.TLD'. In my understanding, these two commands create the exact same HTTP request. The only difference is that in the latter one I take out the DNS lookup part from cURL and do this manually (please correct me if I'm wrong). All well so far. But now I want to do the same for an HTTPS url. Again, I could test it like this curl https://DOMAIN.TLD. But I want to specify the IP manually, so I run curl https://IP_ADDRESS -H 'Host: DOMAIN.TLD'. Now I get a cURL error: curl: (51) SSL: certificate subject name 'DOMAIN.TLD' does not match target host name 'IP_ADDRESS'. I can of course get around this by telling cURL not to care about the certificate (the "-k" option) but it's not ideal. Is there a way to isolate the IP address being connected to from the host being certified by SSL?

  Read the article

• Traceroute to IP address fails, but traceroute to domain name with same IP address is okay. Why?

  - by tomo

  When I traceroute to this IP (108.162.198.181) it stops after 1 hop. But tracerouting to a domain (www.gomodule.com) with the same IP shows 9 hops ending in that target. traceroute to www.gomodule.com (108.162.198.81), 64 hops max, 52 byte packets 1 192.168.1.1 (192.168.1.1) 131.667 ms 48.532 ms 48.837 ms 2 118.69.255.124 (118.69.255.124) 91.521 ms 79.177 ms 30.679 ms 3 42.117.11.225 (42.117.11.225) 30.270 ms 32.091 ms 29.698 ms 4 118.69.253.213 (118.69.253.213) 32.234 ms 118.69.253.237 (118.69.253.237) 70.667 ms 118.69.253.213 (118.69.253.213) 82.440 ms 5 118.69.253.245 (118.69.253.245) 64.554 ms 80.277 ms 130.224 ms 6 118.69.251.205 (118.69.251.205) 65.635 ms 118.69.249.78 (118.69.249.78) 133.234 ms 118.69.251.205 (118.69.251.205) 224.111 ms 7 118.69.251.249 (118.69.251.249) 156.679 ms 111.965 ms 64.165 ms 8 cloudflare1-rge.hkix.net (202.40.160.246) 64.102 ms 64.498 ms 74.581 ms 9 108.162.198.81 (108.162.198.81) 66.873 ms 67.426 ms 69.054 ms -vs- traceroute to 108.162.198.181 (108.162.198.181), 64 hops max, 52 byte packets 1 192.168.1.1 (192.168.1.1) 96.588 ms 3.003 ms 4.976 ms 2 118.69.255.124 (118.69.255.124) 45.223 ms 31.449 ms 31.225 ms 3 * * * 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * ...

  Read the article

• Sync desktop Mac environment to laptop

  - by Andrew Vit

  I spend the majority of my time working at my desktop Mac, which I have configured for my web development environment. My spouse has a MacBook for casual use, and I occasionally steal it back when I need to work off-site, or when travelling. The question is how to best synchronize the two so I can switch between them more readily. I've solved a few obvious things by using online services: Email is hosted on IMAP. Working files are in Dropbox. Source code is managed in git. However, the following are things I always miss when jumping on the laptop: Installed Applications (current versions) Installed libraries & utilities (/usr/local) Apache VirtualHosts & other configurations (/etc) Disk image files for VMs My current method is to connect the MacBook via Firewire target mode and rsync the /Users/me home directory, and then cherry-pick the other items I need from Applications, /etc and /usr/local. The problem with this method is that it can be very time consuming due to things like my virtual machine image files, cached emails, etc. How can I make this faster & easier? Can you recommend a solution for configuration management (so I can repeatably install & configure the same software on both), or synchronization (so I can bring the MacBook up to date nightly, over our home network)?

  Read the article

• Should I keep my ex-employer's data?

  - by Jurily

  Following my brief reign as System Monkey, I am now faced with a dilemma: I did successfully create a backup and a test VM, both on my laptop, as no computer at work had enough free disk space. I didn't delete the backup yet, as it's still the only one of its kind in the company's history. The original is running on a hard drive in continuous use since 2006. There is now only one person left at the company, who knows what a backup is, and they're unlikely to hire someone else, for reasons very closely related to my departure. Last time I tried to talk to them about the importance of backups, they thought I was threatening them. Should I keep it? Pros: I get to save people from their own stupidity (the unofficial sysadmin motto, as far as I know) I get to say "I told you so" when they come begging for help, and feel good about it I get to say nice things about myself on my next job interview Nice clean conscience Bonus rep with the appropriate deities Cons: Legal problems: even if I do help them out with it, they might just sue me for keeping it anyway, although given the circumstances I think I have a good case Legal problems: given the nature of the job and their security, if something leaks, I'm a likely target for retaliation Legal problems: whatever else I didn't think about I need more space for porn. Legal problems. What would you do?

  Read the article

• server dosnt produce syn-ack

  - by steve

  I have a small program that take packets from the nfqueue . change the ip.dst to my server dst (and ttl), recalc checksum and return the packet to the nfqueue. The server and the client are linux and apache web server is run on the server and listen on port 80. i open telnet in the client to fake ip on port 80 . the packet is changed by my program and sent to the server, but the target server (the new dst ip) get the syn , but dosnt generate syn-ack (the server also belong to me , so i can see that it get the syn with checksum correct , but dosnt generate syn-ack). if i do the same , but with the real server ip as the dest, the tcp handshake is done correct (in this case i just change the ttl and checksum. The change that i did to the ttl is just a test to see that my checksum calc is ok). i compare the sys's , but didnt find and difference. Any idea? Ps. i saw this topic : Server not sending a SYN/ACK packet in response to a SYN packet and i set all flags the same , but this didnt help. Thank you

  Read the article

• Prevent Outlook 2010 Insert Picture resizing image

  - by Rup

  When I "Insert Picture" a JPEG in Outlook 2010 it automatically resizes the image and, I think, recompresses it too. I realise this would be useful for photographs or for people who try to email 1MB BMPs but I would like to email around an image at the original pixel size without recompression. Is there a way to turn this off, or better still choose settings for each image insert? I found this page in the Office help. It's for Word, PowerPoint and Excel not Outlook but points you at File, Options, Advanced, Image Settings. There's no equivalent section in Outlook. I know Outlook uses Word as its editor so I've looked at Word's settings but there isn't an 'original size' here: there's only 'turn off image recompression' and pick target DPI from 96, 150, 220. I guess Office is finding a DPI value in the JPEG file and scaling it up or down to match this setting. I can't find an equivalent option in Outlook's options menu but there's so many settings and pop-up dialogs I may have missed something. Picture Format, Reset image size resets the image to the rescaled version, not the original. I can't see a way to edit a pixel value into size values in the image properties after insert. Thanks! I realise I can probably achieve this by editing the image metadata in PhotoShop elements or similar but there ought to be a way without editing the file? This is new behaviour in Outlook 2010; 2007 didn't do this.

  Read the article

• Copy all installed programs & files in a hard disk (which has 32 bit Windows 7) and clone/transfer it to another computer which has 64 bit Windows 7

  - by galacticninja

  I recently got a new PC which has a 64-bit Windows 7 installed. The current PC that I am using has a 32-bit Windows 7 installed. I would like to know if there is a software that can copy all my installed programs and files in the hard disk with the 32-bit Windows 7 PC and transfer it to the newer PC's hard disk which has a 64 bit version of Windows 7. This is essentially like "cloning" a hard disk but I would like to use a 64-bit OS in the target drive, instead of also using the 32-bit OS of the source drive. I would like to do this I can avoid reinstalling and reconfiguring my installed programs and files again on the new PC. If possible, I would like the new PC to work as it was in my previous PC, with the installed programs, configuration and files intact except that the OS is now 64-bit and the hard disk has a larger capacity. I have heard of programs that can clone a hard disk, but my concern is that the 32-bit Windows 7 OS will also be cloned to the new 64-bit PC. If it is not possible to transfer my installed programs and settings like the way I described, are there software that can make it easier to migrate my installed programs, their configurations and my files from a 32-bit Windows 7 PC to a 64-bit Windows 7 PC? Details: I have a SATA to USB connector/adapter to copy files in the current hard disk to the newer one. The two PCs are connected through LAN, so I can also transfer files through LAN. Both PCs only have one hard disk.

  Read the article

• Problems installing Windows service via Group Policy in a domain

  - by CraneStyle

  I'm reasonably new to Group Policy administration and I'm trying to deploy an MSI installer via Active Directory to install a service. In reality, I'm a software developer trying to test how my service will be installed in a domain environment. My test environment: Server 2003 Domain Controller About 10 machines (between XP SP3, and server 2008) all joined to my domain. No real other setup, or active directory configuration has been done apart from things like getting DNS right. I suspect that I may be missing a step in Group Policy that says I need to grant an explicit permission somewhere, but I have no idea where that might be or what it will say. What I've done: I followed the documentation from Microsoft in How to Deploy Software via Group Policy, so I believe all those steps are correct (I used the UNC path, verified NTFS permissions, I have verified the computers and users are members of groups that are assigned to receive the policy etc). If I deploy the software via the Computer Configuration, when I reboot the target machine I get the following: When the computer starts up it logs Event ID 108, and says "Failed to apply changes to software installation settings. Software changes could not be applied. A previous log entry with details should exist. The error was: An operations error occurred." There are no previous log entries to check, which is weird because if it ever actually tried to invoke the windows installer it should log any sort of failure of my application's installer. If I open a command prompt and manually run: msiexec /qb /i \\[host]\[share]\installer.msi It installs the service just fine. If I deploy the software via the User Configuration, when I log that user in the Event Log says that software changes were applied successfully, but my service isn't installed. However, when deployed via the User configuration even though it's not installed when I go to Control Panel - Add/Remove Programs and click on Add New Programs my service installer is being advertised and I can install/remove it from there. (this does not happen when it's assigned to computers) Hopefully that wall of text was enough information to get me going, thanks all for the help.

  Read the article

• linux container bridge filters ARP reply

  - by Dani Camps

  I am using kernel 3.0, and I have configured a linux container that is bridged to a tap interface in my host computer. This is the bridge configuration: :~$ brctl show bridge-1 bridge name bridge id STP enabled interfaces bridge-1 8000.9249c78a510b no ns3-mesh-tap-1 vethjUErij My problem is that this bridge is dropping ARP replies that come from the ns3-mesh-tap-1 interface. Instead, if I statically populate the ARP tables and ping directly everything works, so it has to be something related to ARP. I have read about similar problems in related posts, and I have tried with the solutions explained therein but nothing seems to work. Specifically: ~$ grep net.bridge /etc/sysctl.conf net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 arptables and ebtables are not installed. iptables FORWARD is all set to accept: Chain FORWARD (policy ACCEPT) target prot opt source destination The bridged interfaces are set to PROMISC: ~$ ifconfig ns3-mesh-tap-1 Link encap:Ethernet HWaddr 1a:c7:24:ef:36:1a ... UP BROADCAST PROMISC MULTICAST MTU:1500 Metric:1 vethjUErij Link encap:Ethernet HWaddr aa:b0:d1:3b:9a:0a .... UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 The macs learned by the bridge are correct (checked with brctl showmacs). Any insight on what I am doing wrong would be greatly appreciated. Best Regards Daniel

  Read the article

• MRTG Monitoring of Disk

  - by Antitribu

  I am trying to monitor Disk usage over SNMP using MRTG on CentOS5.2. I'm open to any suggestions as to the best way to achieve this (I would also like to do other metrics like CPU). Please don't assume I know anything about MRTG. I am using the following config: LoadMIBs: /usr/share/snmp/mibs/UCD-SNMP-MIB.txt,/usr/share/snmp/mibs/TCP-MIB.txt workdir: /var/www/html/mrtg/temp/ # # Disk Usage Monitoring # Target[servername.]: dskPercent.0&dskPercent.0:[email protected] Title[servername.]: / on servername routers.cgi*Desc[servername.]: / on servername routers.cgi*ShortDesc[servername.]: / MaxBytes[servername.]: 100 AbsMax[servername.]: 100 Options[servername.]: growright,nopercent,gauge YLegend[servername.]: used disk space ShortLegend[servername.]: % used Legend1[servername.]: usage Legend2[servername.]: usage Legend3[servername.]: peak usage Legend4[servername.]: peak usage LegendI[servername.]: usage LegendO[servername.]: usage routers.cgi*Icon[servername.]: disk-sm.gif routers.cgi*Options[servername.]: noo,nomax,noabsmax Unscaled[servername.]: dwmy I receive the errors: Unknown SNMP var dskPercent.0 at /usr/bin/mrtg line 2035 Unknown SNMP var dskPercent.0 at /usr/bin/mrtg line 2035 From forum surfing etc the suggestion is to use the fully qualified OIDs, I'd like to avoid this (for readability). So essentially I'm wondering where can I find a mib file compatible with mrtg for it's reference or a working config file.

  Read the article

• Iptables rules, forward between two interfaces

  - by Marco

  i have a some difficulties in configuring my ubuntu server firewall ... my situation is this: eth0 - internet eth1 - lan1 eth2 - lan2 I want that clients from lan1 can't communicate with clients from lan2, except for some specific services. E.g. i want that clients in lan1 can ssh into client in lan2, but only that. Any other comunication is forbidden. So, i add this rules to iptables: #Block all traffic between lan, but permit traffic to internet iptables -I FORWARD -i eth1 -o ! eth0 -j DROP iptables -I FORWARD -i eth2 -o ! eth0 -j DROP # Accept ssh traffic from lan1 to client 192.168.20.2 in lan2 iptables -A FORWARD -i eth1 -o eth2 -p tcp --dport 22 -d 192.168.20.2 -j ACCEPT This didn't works. Doing iptables -L FORWARD -v i see: Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 33 144 DROP all -- eth1 !eth0 anywhere anywhere 0 0 DROP all -- eth2 !eth0 anywhere anywhere 23630 20M ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1 any anywhere anywhere 175 9957 ACCEPT all -- eth1 any anywhere anywhere 107 6420 ACCEPT all -- eth2 any anywhere anywhere 0 0 ACCEPT all -- pptp+ any anywhere anywhere 0 0 ACCEPT all -- tun+ any anywhere anywhere 0 0 ACCEPT tcp -- eth1 eth2 anywhere server2.lan tcp dpt:ssh All packets are dropped, and the count of packets for the last rule is 0 ... How i have to modify my configuration? Thank you. Regards Marco

  Read the article

• What's going on with traceroute?

  - by Kevin

  The following is what happens when I run traceroute from a certain location: # traceroute google.com traceroute to google.com (74.125.227.39), 30 hops max, 60 byte packets 1 gateway.local.enactpc.com (10.0.0.1) 0.138 ms 0.101 ms 0.084 ms 2 * * * 3 * * * 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * Absolutely nothing of interest... Now, originally I thought this was just a fact of the location's network set up. (I assume they block pings or something...) However, watch what happens when I use nmap to run a traceroute... # nmap -sP --traceroute google.com Starting Nmap 5.21 ( http://nmap.org ) at 2012-09-25 22:18 CDT Nmap scan report for google.com (74.125.227.40) Host is up (0.034s latency). Hostname google.com resolves to 11 IPs. Only scanned 74.125.227.40 rDNS record for 74.125.227.40: dfw06s06-in-f8.1e100.net TRACEROUTE (using proto 1/icmp) HOP RTT ADDRESS 1 0.19 ms gateway.local.enactpc.com (10.0.0.1) 2 1.93 ms 99-20-92-1.lightspeed.austtx.sbcglobal.net (99.20.92.1) 3 25.61 ms 99-20-92-2.lightspeed.austtx.sbcglobal.net (99.20.92.2) 4 ... 6 7 23.68 ms 12.83.68.137 8 31.30 ms gar23.dlstx.ip.att.net (12.122.85.73) 9 ... 10 31.82 ms 72.14.233.65 11 32.27 ms 209.85.250.77 12 32.98 ms dfw06s06-in-f8.1e100.net (74.125.227.40) Nmap done: 1 IP address (1 host up) scanned in 3.29 seconds When using nmap I get A LOT more results than with traceroute, why? Note, I checked, and the difference in target IP addresses is not related...

  Read the article

• How to diagnose storage system scaling problems?

  - by Unknown

  We are currently testing the maximum sequential read throughput of a storage system (48 disks total behind two HP P2000 arrays) connected to HP DL580 G7 running RHEL 5 with 128 GB of memory. Initial testing has been mainly done by running DD-commands like this: dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=3000 In parallel for each disk. However, we have been unable to scale the results from one array (maximum throughput of 1.3 GB/s) to two (almost the same throughput). Each array is connected to a dedicated host bust adapter, so they should not be the bottleneck. The disks are currently in JBOD configuration, so each disk can be addressed directly. I have two questions: Is running multiple DD commands in parallel really a good way to test maximum read throughput? We have noticed very high SWAPIN-% numbers in iotop, which I find hard to explain because the target is /dev/null How shoud we proceed in trying to find the reason for the scaling problem? Do you thing the server itself is the bottleneck here, or could there be some linux parameters that we have overlooked?

  Read the article

• Best way to build / implement a corporate developer Linux distro with multiple kernels?

  - by Garen

  At work we have Linux users who understandably prefer using Ubuntu. Problem is, we also have developer tools that only work with 'officially' supported Linux distributions that use much older 2.6.18 based kernels. (And even if they worked with newer ones, the vendors could always say they won't "support" the software unless it's on one of their 'officially' supported platforms.) We could of course just tell them to use CentOS or something else 2.6.18-based, and I'm sure their response would be something like: "you can take Ubuntu from our cold, dead hands." :) Which brings to me some questions--is there any good/easy/recommended way to run something like Ubuntu as a host VM and Centos 5.x as a guest OS (with which system--Xen,KVM,VMWare, ...?), and then roll that into our own custom internal distribution that could be easily installed? KVM looks like a good high-performance option just recently included in RHEL 5.4, but if hardware support for virtualization like Intel-VT or AMD-V is necessary, then I'd guess only those folks with fairly new PCs will be able to do it. Would be very interested to hear how anyone else has addressed this kind issue. EDIT: The target audience / users of this kind of system would be developers, each one needs to run locally licensed commercial software, so building out some separate beefy central machines isn't an option unfortunately due to license restrictions. Even if that weren't the case, a couple developers could quickly eat up the resources with parallel builds. :) Ideally, I was hoping there was some step-by-step guide out there to build your own pre-built distribution that had e.g. CentOS 5.x and Ubuntu Desktop as a guest.

  Read the article

• Syntax error at '{'; expected '}' when using nagios in puppet

  - by jiangchengwu

  It's a big problem to me, because I'm not familiar with puppet. ERROR on the puppetmaster: debug: importing '/etc/puppet/manifests/nodes/group-1.pp' err: Could not parse for environment production: Syntax error at '{'; expected '}' at /etc/puppet/manifests/nodes/group-1.pp:6 ERROR on the puppet client: err: Could not retrieve catalog from remote server: Error 400 on SERVER: Could not parse for environment production: Syntax error at '{'; expected '}' at /etc/puppet/manifests/nodes/group-1.pp:6 in group-1.pp: node 'group1' { include ntp class { 'nagios::host': #this is line 6 nodename => $clientcert, appname => 'test', } } nagios::host in module module/nagios/host.pp code are here: class nagios::host($nodename, $hostgroup) { file { '/usr/lib/nagios/plugins': mode = "755", require = Package["nagios-plugins"], } ... @@nagios_service { "${nodename}_check_ssh": ensure => present, use => 'generic-service', host_name => "${nodename}", notification_interval => 60, flap_detection_enabled => 0, service_description => "SSH", check_command => "check_ssh", target => "/etc/nagios3/services.d/${nodename}.cfg", } } and the file module/nagios/init.pp is blank How could I fix it ?

  Read the article

• How to make an x.509 certificate from a PEM one?

  - by Ken

  I'm trying to test a script, locally, which involves uploading a file using a Java-based program to a FileZilla FTPES server. For the real thing, there is a real certificate on the FZ server, and the upload step (tested alone) seems to work fine. I've installed FileZilla Server on my dev box (so it'll test uploading from localhost to localhost). I don't have a real certificate for it, of course, so I used the "Generate new certificate..." button in FZ. It works fine from an interactive FTPES program (as long as I OK the unknown cert), but from my Java program it throws a javax.net.ssl.SSLHandshakeException ("unable to find valid certification path to requested target"). So how do I tell Java that this certificate is OK with me? (I know there's a way to change the Java program to accept any certificate, but I don't want to go down that route. I want to test it just as it will happen in production, and I don't want to ignore unknown certificates in production.) I found that Java has a program called "keytool" that seems to be for managing this sort of thing, but it complains that the certificate file that FZ generated is not an "x.509" file. A posting from the FZ side said it was "PEM encoded". I have "openssl" here, which looks like it's perfect for converting between certificate formats, but I think my understanding of certificate formats is wrong because I'm not seeing anything obvious. My knowledge of security certificates is a bit shaky, so if my title is stupidly wrong, please help by fixing that. :-)

  Read the article

• How do I stop linux from trying to mount android phone as usb storage?

  - by user1160711

  When I plug in my Motorola Triumph to my fedora 17 linux box USB port, I get an endless series of errors on the linux box as it desperately attempts to mount the phone as a USB drive. Stuff like this: Jun 23 10:26:00 zooty kernel: [528926.714884] end_request: critical target error, dev sdg, sector 4 Jun 23 10:26:00 zooty kernel: [528926.715865] sd 16:0:0:1: [sdg] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 23 10:26:00 zooty kernel: [528926.715869] sd 16:0:0:1: [sdg] Sense Key : Illegal Request [current] Jun 23 10:26:00 zooty kernel: [528926.715872] sd 16:0:0:1: [sdg] Add. Sense: Invalid field in cdb Jun 23 10:26:00 zooty kernel: [528926.715876] sd 16:0:0:1: [sdg] CDB: Read(10): 28 20 00 00 00 00 00 00 04 00 If I go ahead and tell the phone to allow linux to mount the USB storage, the messages stop, and I get a mounted drive, but if all I want to do is use the debug bridge, my log on linux will continue to fill with this junk. Is there some udev magic I can do to make the system ignore this particular device as far as usb storage goes? I just noticed that if I tell the phone to enable USB storage, let linux recognize the new disk, then tell the phone to disable USB storage again, I get one additional log message about capacity changing to zero, but the endless spew of messages stops, so I guess one work around is to enable and disable USB right away.

  Read the article

• Why is my hg workbench & Adobe Reader toolbar icon a blank white page?

  - by Zasurus

  On my work's PC (windows 7 32bit) all Adobe Reader and hg Workbench icons on the toolbar (and general shortcuts for hg workbench) are just white pages (with the top left corner folded over). If you right click on the toolbar icon then right click on "TortoiseHg Workbench"(for hg workbench) then "Properties" then the "Change Icon..." button is greyed out (same for "Adobe Reader X"). Also the "Target:" is "TortoiseHg 2.4.0 (x86)" and is greyed out also the "Open File Location" is greyed out. This is the same for both Hg Workbench and Adobe Reader and seems to be the only thing that connects them. I have tried reinstalling to no avail. I also have local admin rights on the PC. I finally I have tried the following following questions without any luck (they aren't quite relevant to my issue but close): Adobe Reader program icon and pdf icons don't appear in Windows 7 Adobe PDF icon disappeared? Encase my description isn't enough to understand the issue here is a screenshot. As you can see the Hg Workbench icon (far left) and a pdf open in Adobe Reader X (second icon to from the left) are both blank and the shortcut is mainly greyed out.

  Read the article

• What is going on when I can't access an SMB server share (not accessible error) until I run cmdkey to delete the credential?

  - by Warren P

  I have a network connection share issue. The first connection works, and seems to stay connected for at least a few hours. However, after each time my windows 7 PC reboots, it can no longer form a network connection to the shared folder, nor browse to it, until I not only unmap and remap the mapped drive, but also, I have to use cmdkey to delete the stored credentials like this: cmdkey /delete:Domain:target=HOSTNAME My work PC is on a domain, and I am not the IT administrator, but I'm curious if there is anything I can do to investigate this issue. Any settings in registry or group policy that I could examine to see why the first connection works, but each subsequent attempt (once a stored credential exists) to browse or use the connection, fails with a connection error saying it is "not accessible", like this: I do not even get any error until at least several minutes go by. THe first thing I see is a window frozen and empty, and then I get this error: This has happened when connecting to a share on a DROBO device, and on a share which is not on the domain, but which was a Microsoft Home Server. I wonder if there's something broken in WIndows 7 professional with regards to connecting to non-domain shares when an active directory domain controller exists, and a particular workstation is joined to a domain? The problem only occurs if I click "remember credentials". It is not fixed by any amount of working with net use. Usingcmdkey to delete all stored credentials for the host is the only way to get back in, and it affects all non-domain shared folders. Update I'm hoping there are some registry locations I could check that could be misconfigured in some way that might explain why SMB/CIFS stored credentials for non-domain systems seem to be auto-invalidated in this weird way. Knowing how whacko Microsoft Windows domain and security handling is sometimes, this could be some kind of stupid "feature".

  Read the article

< Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >