Search Results

Search found 8238 results on 330 pages for 'dynamic disks'.

Page 215/330 | < Previous Page | 211 212 213 214 215 216 217 218 219 220 221 222  | Next Page >

  • LinkSys WRT54GL + AM200 in half-bridge mode - Setup guide recommendations?

    - by Peter Mounce
    I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. My ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • hp DL380 G4 won't boot with disk plugged into front USB

    - by Kev
    We outgrew a few older external USB backup drives, and purchased WD My Passport 1 TB USB 3.0 drives to replace them. When they are plugged into the front of our G4, it will blink forever after the BIOS (which is current, BTW) and never boot, even though the USB disks are not "bootable" per se. Our old drives did not exhibit this behaviour (so I don't think it's this type of issue that I've read about other servers.) The old drives were USB 2.0, but this shouldn't make a difference, AFAICT--the specs say all of the G4's USB ports are the same, 2.0, anyway, so I'm not sure how one port would handle a USB 3.0 device better than another. If we plug the new drives in one of the back slots, it boots fine. What's the cause? My concern is that the front USB port, and possibly the motherboard, might be starting to die. (We are experiencing other strange issues with them, or were initially, like intermittent file permissions errors despite wide-open ACL on these local drives, but some serverfault users have me convinced they may be coincidental software/security related issues.)

    Read the article

  • is it possible for a router to provide different gateway?

    - by Hao
    i have tp-link wireless router 192.168.10.188, i was can make it function as DHCP provider(range 192.168.10.100 to 192.168.10.109). the only thing that i cannot make it work as intended, is for it to provide different gateway (192.168.10.1), the computers that obtain IP from that router properly get everything(dynamic IP and dns IP), but there is no function on that router to provide different gateway, the computers always get the router's address(192.168.10.188) as gateway. is there a router that can provide different gateway other than its own address? or the question should be, is the dhcp of a router can provide different gateway other than its own address? note: i cannot make the wireless router address as 192.168.10.1, we have main router(non-wireless, address is 192.168.10.1) that is connected directly to internet

    Read the article

  • Var null and not an object when using document.getElementById

    - by Dean
    Hi, I'm doing some work in HTML and JQuery. I have a problem of my textarea and submit button not appearing after the radio button is selected. My HTML looks like this: <html> <head><title>Publications Database | Which spotlight for Publications</title> <script type="text/javascript" src="./jquery.js"></script> <script src="./addSpotlight.js" type="text/javascript" charset="utf-8"></script> </head> <body> <div class="wrapper"> <div class="header"> <div class="headerText">Which spotlight for Publications</div> </div> <div class="mainContent"> <p>Please select the publication that you would like to make the spotlight of this month:</p> <form action="addSpotlight" method="POST" id="form" name="form"> <div class="div29" id="div29"><input type="radio" value="29" name="publicationIDs" >A System For Dynamic Server Allocation in Application Server Clusters, IEEE International Symposium on Parallel and Distributed Processsing with Applications, 2008 </div> <div class="div30" id="div30"><input type="radio" value="30" name="publicationIDs" >Analysing BitTorrent's Seeding Strategies, 7th IEEE/IFIP International Conference on Embedded and Ubiquitous Computing (EUC-09), 2009 </div> <div class="div31" id="div31"><input type="radio" value="31" name="publicationIDs" >The Effect of Server Reallocation Time in Dynamic Resource Allocation, UK Performance Engineering Workshop 2009, 2009 </div> <div class="div32" id="div32"><input type="radio" value="32" name="publicationIDs" >idk, hello, 1992 </div> <div class="div33" id="div33"><input type="radio" value="33" name="publicationIDs" >sad, safg, 1992 </div> <div class="abstractWriteup" id="abstractWriteup"><textarea name="abstract"></textarea> <input type="submit" value="Add Spotlight"></div> </form> </div> </div> </body> </html> My javascript looks like this: $(document).ready( function() { $('.abstractWriteup').hide(); addAbstract(); }); function addAbstract() { var abstractWU = document.getElementById('.abstractWriteup'); $("input[name='publicationIDs']").change(function() { var abstractWU = document.getElementById('.abstractWriteup'); var classNameOfSelected = $("input[name='publicationIDs']").val(); var radioSelected = document.getElementById("div"+classNameOfSelected); var parentDiv = radioSelected.parentNode; parentDiv.insertBefore(radioSelected, abstractWU.nextSibling); $('.abstractWriteup').show(); });}; I have developed this by using Node#insertBefore. When I have had it working it has been rearranging the radio buttons. Thanks in Advance Dean

    Read the article

  • Moving the Windows 7 Pro OEM image to computer with the same hardware

    - by SWin
    We bought 8 clean computers (even without HDD) with the same hardware and bought eight Windows 7 Pro OEM disks. Now I prepare one Win7 installation without activation but with all required programs, settings, etc. Then I'm going to clone the image to other computers even without sysprepping. I'm going to change the product key to legal number at COA sticker on each computer and make the activation through the Internet. Will this scenario work? I know that OEM's license agreement forbids the image cloning and the actions I'm going to do breaks the agreement. According the license agreement I should make the manual clean install of Win7 on each computer. But how Microsoft and other viewers can determine the cloning fact? All computers are the same and license Win7 DVDs are also the same. However in my case the installation time also will the same (and may be kind of installation code or something else) and this is not good. Will the Win7 activation work? Can I be sure that activation will not damage after some time? Can Microsoft determine the cloning fact during the activation process? Thank you.

    Read the article

  • Cannot remove storage account because of lease, but I already deleted the server [closed]

    - by djechelon
    I recently created a temporary virtual server on Azure. Then I deleted it. I wanted to delete the storage account associated with it because I didn't need it any more. The problem is that the VHD file is still associated to a non-existing virtual machine!! If I try to delete the VHD from Virtual Machines\Disks I get the Delete button greyed and the table tells me it's still associated with the old VM. If I go to storage administration and try to delete the blob from vhds/ directory I get there is an active lease. I've read on Azure forums that, in these case, one should try to force releasing the lease from the blob. I followed their instructions and downloaded their script, but running it failed. The script detected that the disk is associated to a Virtual Machine and can't be deleted. The problem is that I'm 1000000% sure that I already deleted the VM. In fact, I currently only have a single VM that has its own HD and is up and running fine! What can I do to delete that storage account that is probably sucking money from my pocket?

    Read the article

  • APC module causing strange error

    - by clifgriffin
    When I run php -v I get: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/apc.so' - /usr/lib64/php/modules/apc.so: undefined symbol: php_pcre_exec in Unknown on line 0 This isn't my first rodeo. I've setup APC multiple times. This is a MediaTemple Dedicated Virtual 4.0 with Plesk 11. Plesk 11 is the only thing essentially different from the other servers I've set this up on. I've verified that pcre-devel is installed. I've compiled APC from source as well as used pecl to install it. No difference. I also tried downgrading to APC 3.0.19, with no love.

    Read the article

  • ASUS K55VM Laptop unexpectedly shuts down

    - by Abhishek Sha
    I've read quite a few questions on SuperUser of people having laptop shutdown problems but mine is different. My laptop specs: Intel Core i7 3610QM (IvyBridge) NVIDIA GT630M 2GB and Intel GMA4000 8GB RAM Windows 7 64 Bit My laptop occasionally shuts down when playing FarCry 3. It's around 5 months old. I've played games like Crysis and it never shuts down unexpectedly. Since I experienced this shut down recently, I decided for GPU-Z to log the temperatures. The final log value at the time of shutdown were thus: GPU Core Clock [MHz] - 797.3 GPU Memory Clock [MHz] - 896.8 GPU Temperature [°C] - 89.0 GPU Load [%] - 99 Memory Controller Load [%] - 36 Video Engine Load [%] - 0 Memory Usage (Dedicated) [MB] - 535 Memory Usage (Dynamic) [MB] - 53 VDDC [V] - 1.0620 My drivers are up-to-date and I didn't encounter any BSODs at the time of shut down. It simply turns off.

    Read the article

  • Computer sponteously reboots when doing heavy file copy to/from disk

    - by Mark Hosang
    I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

    Read the article

  • IIS not listening over external network, all other traffic working

    - by Beuy
    Hello there, I have a very odd situation, I have a server (let's call it X) running 2008 R2 with two NIC's in it, one is connected to the work domain and has a subnet of 192.168.10.0/24 the other is connected to a ADSL connection and has a subnet of 192.168.1.0/24. The server has IIS installed. On the ADSL connection I have setup a dynamic dns and port forwarding to allow external HTTP, HTTPS, FTP and RDP connections. FTP and RDP are working fine however neither HTTP or HTTPS are working at all. I can browse the websites by going to localhost on the machine, the HTTP and HTTPS ports appear as "Filtered" when I try to scan them using PortQueryUI and browsers respond with a "Server took too long to load or was not responding" error. This was working fine just a few days ago, Windows firewall is disabled I don't have any software firewall on it. And I'm really lost. Any help would be great.

    Read the article

  • Web Server for SVN+PHP+Django+Rails

    - by NetStudent
    Foreword: I am not asking for the differences between Nginx and Apache, nor do I want to start a "which one is better discussion. I would like to ask for help with choosing the most adequate solution for this particular situation. I need to setup one or more l SVN repositories accessible via HTTP, plus some PHP, Django and Ruby websites. However, and since I only have 512Mb of RAM at my disposal, I fear that Apache will be a too heavy choice... On the other hand, I have heard that Nginx does not fully support SVN (WebDAV) and Django without reverse proxying to Apache. Is this still true? Should I go for Apache/Nginx alone? Or should I set up both and have Nginx handling static content and proxying to Apacge for dynamic content?

    Read the article

  • Synchronising a remote folder with a local one.

    - by Workshop Alex
    I am using a network disk (that's connected to my router by USB) to store several data files. A simple .NET application that I've created is supposed to read and modify these data files. However, some security issues are preventing this application to access these files directly. (Actually, these have been built-in to my application on purpose since it's not going to support NAS disks.) Since this disk is shared with several computers, I just want to have a simple synchronisation method, which will copy the files to a local folder where3 my application can access them. And, once modified, it should send back the modified files to the NAS disk again. I have two options: 1) Build a second application to do my own synchronisation. 2) Find some build-in function inside Windows 7 Ultimate which can do this for me. Option 2 is preferred. Option 1 is something I can do easily, if need be. I don't need third-party tools. (Still, feel free to add some references to good tools, although I won't accept them as answers.) Basically, is this possible with Windows 7 and if so, how?

    Read the article

  • Missing whole disk device in OpenSolaris

    - by Jeff Mc
    I have begun experimenting with Solaris and ZFS as a NAS. All was going very smoothly until I had a drive failure. When I replaced the drive, I no longer have a device file mapped to the whole disk. /dev/dsk/c7t3d0 does not exist but c7t2d0 and c7t4d0 both do. Also the sd@3,0:wd file under the /devices/ tree is non-existent. Do I have to prepare/partition the disk somehow to cause the whole disk device to exist? Here are a few outputs that might be useful. jeffmc@ats-ds2:/dev/dsk$ zpool status pool: datapool state: DEGRADED status: One or more devices could not be opened. Sufficient replicas exist for the pool to continue functioning in a degraded state. action: Attach the missing device and online it using 'zpool online'. see: http://www.sun.com/msg/ZFS-8000-2Q scrub: none requested config: NAME STATE READ WRITE CKSUM datapool DEGRADED 0 0 0 mirror-0 DEGRADED 0 0 0 c7t2d0 ONLINE 0 0 0 c7t3d0 UNAVAIL 0 0 0 cannot open mirror-1 ONLINE 0 0 0 c7t4d0 ONLINE 0 0 0 c7t5d0 ONLINE 0 0 0 jeffmc@ats-ds2:/dev/dsk$ zpool replace datapool c7t3d0 cannot open 'c7t3d0': no such device in /dev/dsk must be a full path or shorthand device name jeffmc@ats-ds2:/dev/dsk$ sudo format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c7t0d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@0,0 1. c7t1d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@1,0 2. c7t2d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@2,0 3. c7t3d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@3,0 4. c7t4d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@4,0 5. c7t5d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@5,0

    Read the article

  • How do I add a WMware ESXi Host to Microsoft Virtual Machine Manager?

    - by user63250
    I am trying to manage virtual machines running on a VMware ESXi host using Microsoft System Center Virtual Machine Manager. I was able to add the ESXi machine using the "Add VMware VirtualCenter server" option, but can't access any of the VMs on the datastore associated with this ESXi server. The datastore of the ESXi box is showing up with the correct name, but it won't let me see any of the VMs that have already been created; I get "There are no virtual machines on this host." Because I couldn't get any of the existing virtual machines to show up, I tried creating some new ones. When using VMM to connect to ESXi and create new VMs, I get the following error messages in the "rating explanation" section: The virtualization software on the selected host does not support virtual hard disks on an IDE bus. and The virtualization software on the host XXXXXX does not support the creation of dynamic virtual hard disk. Any ideas on why I can't manage existing machines and why I can't create new ones? The existing machines were created in vSphere. I should note that the ESXi server and the server running SCVMM are both on the same domain. I should also note that although the ESXi box has been added as a VirtualCetner server, when I try to add it through the "Add Host" option, I get an error message saying "Virtual Machine Manager cannot complete the VirtualCenter action on server EXSi because of the following error: The operation is not supported on the object."

    Read the article

  • Ubuntu 12.04 VPS doesn't boot with mysql in nsswitch.conf

    - by chrisv
    1and1 VPS ("dynamic cloud server") does not boot any more as soon as mysql lookup is enabled in nsswitch.conf - any suggestions appreciated. Minimal setup to reproduce the problem: install Ubuntu 12.04 / LTS minimal server image install mysql-server, libnss-mysql-bg, nscd configure /etc/libnss-mysql.cfg and /etc/libnss-mysql-root.cfg set up appropriate database tables configure nss lookups through mysql in nsswitch.conf passwd: compat mysql group: compat mysql shadow: compat mysql Now, when I try to reboot the server it just hangs. No logs (maybe due to /var not yet being mounted), and I can't see console output (since this is a VPS). Booting into recovery image and removing "mysql" from /etc/nsswitch.conf makes the system bootable again, so this is definitely related to nsswitch/libnss-mysql-bg. There's a thread on gentoo-users which seems to describe a similar problem, unfortunately there's no real solution described, also the thread is rather old (from 2006) so I'm not sure whether this applies to me at all.

    Read the article

  • Sharing a folder with Nautilus and NTFS external drive gets errors

    - by TheLQ
    I am trying to share a folder in Lubuntu over a network that's on an external NTFS drive. Due to the system that I have (rotating backup disks) this is probably the second time that the drive would of been mounted. Its manually mounted with a simple (for example) mount /dev/sdb1 /media/BACKUP On an internal NTFS disk I have successfully setup a network share and can access it. However on the external disk I can't from any other Windows computer. When setting up the share Nautilus said that it needs to change the other's permissions to allow for other users to write. However afterwords its still blank. Changing it to Read and Write just changes back to blank. Chowning the entire /media folder recursively and trying didn't work. Running PCManFM as root and changing didn't work. Adding "public=yes" to smb.conf and restarting didn't work. I'm out of idea's on what to do. What's weird is that it worked just fine on an internal NTFS disk, so why not the external one? Any solutions need to be able to managed inside of a gui (preferably Nautilus) as the person managing the machine isn't as tech savvy. Thanks

    Read the article

  • "DNS not responding" error with D-Link router and PPTP internet connection

    - by Born2win
    I have a D-Link DIR-615 router since around six months. My internet connection is VPN (PPTP) based, i.e. I have been given a username and password from my ISP and my IP address is dynamic. Since a few days I am experiencing a serious problem. My router connects normally (I can see the yellow light), but my computer is giving me a "DNS not responding" error. I have tried everything (reset, reboot etc.) but no success.

    Read the article

  • LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

    - by Peter Mounce
    I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

    - by Peter Mounce
    Crossposted from here I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • COMPAQ Tower No Signal to monitor

    - by Lancelot
    I received a Compaq tower: Compaq Presario SR1224NX Onboard VGA Windows XP SP2 from a friend. My plan was to turn this into an Ubuntu Server. It booted up with no problems even with the Ubuntu live disc. After a normal shutdown (not unplugging the power cord and not doing a hard shutdown with the power button), it would not restart even after SEVERAL attempts. I realized the light next to the power supply would flash very rapidly. I researched and found out it was one of two things: a dead power supply or the cables to the motherboard and to the disks might be faulty, etc. Thus, I checked to ensure the cables were fine(and they were). I purchased a Power Supply (this one has 400 watts, the initial had 250) and installed it. The tower was able to boot into the live disk and everything. After a normal shutdown, it now restarts but is not sending signal to my monitor. I have tried several monitors in which I know work perfectly but not with this tower (I recall that it did show display after replacing the power supply). The monitors are ACER. This is different than most "no Signal" problems since I am not using an external Video Card, this is onboard VGA.

    Read the article

  • Finding a private (NAT) host's IP using historic destination data

    - by l0c0b0x
    The issue: An unknown private (NAT) client is infected with malware and it's trying to access a Bot server at random times/dates. How we know about this: We receive bot traffic notices/alerts from REN-ISAC. Unfortunately, we don't receive those until the next day after it has happened. What they provide to us is: The source address (of the firewall) The destination addresses (it varies, but they're going to network subnet allocated to a German ISP) The source port (which varies--dynamic ports). Question: What would be the best approach to finding this internal host (historically) with a Cisco ASA as firewall? I'm guessing blocking anything to the destination address(es), and logging that type of traffic/access might allow me to find the source host, but I'm not sure which tool/command would be the most useful. I've seen Netflow thrown into a few responses when it comes to logging, but I'm confused with it's association of Logging, NAL, and nBAR, and how they relate to Netflow.

    Read the article

  • Disable RAID to JBOD in server IBM x3400 M2

    - by BanKtsu
    Hi I just wanna disable the default RAID in my server IBM System X3400 M2 Server(7837-24X),i have 3 disk drives SAS. I want to make them a JBOD "Just a Bunch Of Disks", because I want to install in the drive 0 CentOS, and the other two make them cache files for a squid server. I disable the RAID in the BIOS: System Settings/Adapters and UEFI drivers/LSI Logic Fusion MPT SAS Driver -PciRoot(0x0)/Pci(0x3,0X0)/Pci(0x0,0x0) LSI Logic MPT Setup Utility RAID Properties/Delete Array Later I boot the CentOS live CD and install the OS in the drive 0, and the others 2 mounted like this: *LVM Volume Groups vg_proxyserver 139508 lv_root 51200 / ext4 lv_home 84276 /home ext4 lv_swap 4032 Hard Drive sdb(/dev/sdb) free 140011 sdc(/dev/sdc) free 140011 sdd(/dev/sdd) sdd1 500 /boot ext4 sdd2 139512 vg_proxyserver physical volume(LVM) But when I restart the server give me the error: Boot failed Hard Disk 0 UEFI PXE PciRoot(0x0)/Pci(0x1,0X0)/Pci(0x0,0x0)/MAC(001A64B15130,0X0)) ........PXE-E18:Server response timeout. UEFI PXE PciRoot(0x0)/Pci(0x1,0X0)/Pci(0x0,0x0)/MAC(001A64B15132,0X0)) ........PXE-E18:Server response timeout. and the OS not start. The IBM force me to do a RAID?,why?

    Read the article

  • How to find out what is causing a slow down of the application on this server?

    - by Jan P.
    This is not the typical serverfault question, but I'm out of ideas and don't know where else to go. If there are better places to ask this, just point me there in the comments. Thanks. Situation We have this web application that uses Zend Framework, so runs in PHP on an Apache web server. We use MySQL for data storage and memcached for object caching. The application has a very unique usage and load pattern. It is a mobile web application where every full hour a cronjob looks through the database for users that have some information waiting or action to do and sends this information to a (external) notification server, that pushes these notifications to them. After the users get these notifications, the go to the app and use it, mostly for a very short time. An hour later, same thing happens. Problem In the last few weeks usage of the application really started to grow. In the last few days we encountered very high load and doubling of application response times during and after the sending of these notifications (so basically every hour). The server doesn't crash or stop responding to requests, it just gets slower and slower and often takes 20 minutes to recover - until the same thing starts again at the full hour. We have extensive monitoring in place (New Relic, collectd) but I can't figure out what's wrong; I can't find the bottlekneck. That's where you come in: Can you help me figure out what's wrong and maybe how to fix it? Additional information The server is a 16 core Intel Xeon (8 cores with hyperthreading, I think) and 12GB RAM running Ubuntu 10.04 (Linux 3.2.4-20120307 x86_64). Apache is 2.2.x and PHP is Version 5.3.2-1ubuntu4.11. If any configuration information would help analyze the problem, just comment and I will add it. Graphs info phpinfo() apc status memcache status collectd Processes CPU Apache Load MySQL Vmem Disk New Relic Application performance Server overview Processes Network Disks (Sorry the graphs are gifs and not the same time period, but I think the most important info is in there)

    Read the article

  • Does SQLIO lie when run from a Hyper-V guest on a VHD?

    - by ScottStonehouse
    SQLIO seems like a useful tool. I thought it would be interesting to try to measure the speed difference between a physical disk and a VHD. So I ran SQLIO on the Hyper-V host on the physical drive. Results seemed reasonable. Then I ran it from the guest to test the vhd (on the same physical disk). I expected it to be a bit slower. But instead it was way faster - like 0ms average latency. So I'm trying to learn something here. It seems like hyper-v is fooling SQLIO somehow but I don't understand it well enough to figure it out. It's a dynamic vhd, no snapshots or anything, and the vhd is the only file on the disk. The physical disk is actually a two SAS drive RAID 1.

    Read the article

  • vmware esxi 5, cant create snapshots and consolidate fails, how to delete old or consolidate redo logs?

    - by Scott Szretter
    I have a VM that seems to be working ok, but when VMWare DR (or I) tries to create a snap shot, it fails, and when I view the summary page of the VM it has a warning at the top showing that the disks need to be consolidated. So I go to snapshot manager for the VM and choose consolidate (in snapshot manager, there are no snapshots actually listed by the way). If fails with this error: This virtual machine has 255 or more redo logs in a single branch of its snapshot tree. The maximum supported limit has been reached, creating new snapshots will not be allowed. To create new snapshots, please delete old snapshots or consolidate the redo logs. If I browse the data store (which has plenty of free space, 2 TB and this vm is under 40gb), in the vm folder, I do in fact see a bunch of files, numbered all the way to 0255: myvm-000255-ctk.vmdk myvm-000255-delta.vmdk myvm-000255.vmdk How can I clean all this up? Is there an SSH command line command or can I delete some of the files safely? Thanks!

    Read the article

< Previous Page | 211 212 213 214 215 216 217 218 219 220 221 222  | Next Page >